Граф коммитов

59 Коммитов

Автор SHA1 Сообщение Дата
Bartlomiej Zolnierkiewicz 97100fc816 ide: add device flags
Add 'unsigned long dev_flags' to ide_drive_t and convert bitfields
to IDE_DFLAG_* flags.

While at it:
- IDE_DFLAG_ADDRESSING -> IDE_DFLAG_LBA48
- fixup some comments
- remove needless g->flags zeroing from ide*_probe()

There should be no functional changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-10-13 21:39:36 +02:00
Bartlomiej Zolnierkiewicz 3ceca727fe ide: include <linux/hdreg.h> only when needed
* Include <linux/ata.h> directly in <linux/ide.h>
  instead of through <linux/hdreg.h>.

* Include <linux/hdreg.h> only when needed.

Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-10-10 22:39:27 +02:00
Bartlomiej Zolnierkiewicz 3a7d24841a ide: use ATA_* defines instead of *_STAT and *_ERR ones
* ERR_STAT   -> ATA_ERR
* INDEX_STAT -> ATA_IDX
* ECC_STAT   -> ATA_CORR
* DRQ_STAT   -> ATA_DRQ
* SEEK_STAT  -> ATA_DSC
* WRERR_STAT -> ATA_DF
* READY_STAT -> ATA_DRDY
* BUSY_STAT  -> ATA_BUSY

* MARK_ERR   -> ATA_AMNF
* TRK0_ERR   -> ATA_TRK0NF
* ABRT_ERR   -> ATA_ABORTED
* MCR_ERR    -> ATA_MCR
* ID_ERR     -> ATA_IDNF
* MC_ERR     -> ATA_MC
* ECC_ERR    -> ATA_UNC
* ICRC_ERR   -> ATA_ICRC

* BBD_ERR    -> ATA_BBK

Also:

* ILI_ERR    -> ATAPI_ILI
* EOM_ERR    -> ATAPI_EOM
* LFS_ERR    -> ATAPI_LFS

* CD         -> ATAPI_COD
* IO         -> ATAPI_IO

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-10-10 22:39:21 +02:00
Bartlomiej Zolnierkiewicz 48fb2688aa ide: remove drive->driveid
* Factor out HDIO_[OBSOLETE,GET]_IDENTITY ioctls handling
  to ide_get_identity_ioctl().

* Use temporary buffer in ide_get_identity_ioctl() instead
  of accessing drive->id directly.

* Add ide_id_to_hd_driveid() inline to convert raw id into
  struct hd_driveid format (needed on big-endian).

* Use ide_id_to_hd_driveid() in ide_get_identity_ioctl(),
  cleanup ide_fix_driveid() and switch ide to use use raw id.

* Remove no longer needed drive->driveid.

  This leaves us with 3 users of struct hd_driveid in tree:
  - arch/um/drivers/ubd_kern.c
  - drivers/block/xsysace.c
  - drivers/usb/storage/isd200.c

While at it:

* Use ata_id_u{32,64}() and ata_id_has_{dma,lba,iordy}() macros.

There should be no functional changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-10-10 22:39:19 +02:00
Bartlomiej Zolnierkiewicz 4dde4492d8 ide: make drive->id an union (take 2)
Make drive->id an unnamed union so id can be accessed either by using
'u16 *id' or 'struct hd_driveid *driveid'.  Then convert all existing
drive->id users accordingly (using 'u16 *id' when possible).

This is an intermediate step to make ide 'struct hd_driveid'-free.

While at it:

- Add missing KERN_CONTs in it821x.c.

- Use ATA_ID_WORDS and ATA_ID_*_LEN defines.

- Remove unnecessary checks for drive->id.

- s/drive_table/table/ in ide_in_drive_list().

- Cleanup ide_config_drive_speed() a bit.

- s/drive1/dev1/ & s/drive0/dev0/ in ide_undecoded_slave().

v2:
Fix typo in drivers/ide/ppc/pmac.c. (From Stephen Rothwell)

There should be no functional changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-10-10 22:39:19 +02:00
Bartlomiej Zolnierkiewicz 374e042c3e ide: add struct ide_tp_ops (take 2)
* Add struct ide_tp_ops for transport methods.

* Add 'const struct ide_tp_ops *tp_ops' to struct ide_port_info
  and ide_hwif_t.

* Set the default hwif->tp_ops in ide_init_port_data().

* Set host driver specific hwif->tp_ops in ide_init_port().

* Export ide_exec_command(), ide_read_status(), ide_read_altstatus(),
  ide_read_sff_dma_status(), ide_set_irq(), ide_tf_{load,read}()
  and ata_{in,out}put_data().

* Convert host drivers and core code to use struct ide_tp_ops.

* Remove no longer needed default_hwif_transport().

* Cleanup ide_hwif_t from methods that are now in struct ide_tp_ops.

While at it:

* Use struct ide_port_info in falconide.c and q40ide.c.

* Rename ata_{in,out}put_data() to ide_{in,out}put_data().

v2:

* Fix missing convertion in ns87415.c.

There should be no functional changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-07-23 19:55:56 +02:00
Bartlomiej Zolnierkiewicz 3b2a5c7149 ide: filter out "default" transfer mode values in set_xfer_rate()
* Filter out "default" transfer mode values (0x00 - default PIO mode,
  0x01 - default PIO mode w/ IORDY disabled) in write handler for obsoleted
  /proc/ide/hd?/settings:current_speed setting.

  Allowing "default" transfer mode values is a dangerous thing to do as
  we don't support programming controller to the "default" transfer mode
  and devices often use different values for the default and maximum PIO
  mode (i.e. PIO2 default and PIO4 maximum) so the controller will stay
  programmed for higher PIO mode while device will use the lower PIO mode.

  There is no functionality loss as by using special IOCTLs device can
  still be programmed to "default" transfer modes (it is only useful for
  debugging/testing purposes anyway).

* Remove no longer needed IDE_HFLAG_ABUSE_SET_DMA_MODE host flag, it was
  previously used by few host drivers to program the controller to PIO0
  timings for "default" transfer mode == 0x01 (although some host drivers
  would program invalid PIO timings instead).

* Cleanup ide_set_xfer_rate() and add BUG_ON().

Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-07-23 19:55:56 +02:00
Bartlomiej Zolnierkiewicz 9ad5409375 ide: move PIO blacklist to ide-pio-blacklist.c
Move PIO blacklist to ide-pio-blacklist.c.

While at it:

- fix comment

- fix whitespace damage

There should be no functional changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-07-16 20:33:39 +02:00
Bartlomiej Zolnierkiewicz 3e153cfb5e ide: remove no longer used ide_pio_timings[]
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-07-16 20:33:39 +02:00
Bartlomiej Zolnierkiewicz c9d6c1a237 ide: move ide_pio_cycle_time() to ide-timings.c
All ide_pio_cycle_time() users already select CONFIG_IDE_TIMINGS
so move the function from ide-lib.c to ide-timings.c.

While at it:

- convert ide_pio_cycle_time() to use ide_timing_find_mode()

- cleanup ide_pio_cycle_time() a bit

There should be no functional changes caused by this patch.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-07-16 20:33:39 +02:00
Bartlomiej Zolnierkiewicz e4e8d02f56 ide: remove needless includes from ide-lib.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-07-16 20:33:35 +02:00
Bartlomiej Zolnierkiewicz 94cd5b62ff ide: add ->tf_load and ->tf_read methods
* Add ->tf_load and ->tf_read methods to ide_hwif_t and set the default
  methods in default_hwif_transport().

* Use ->tf_{load,read} instead o calling ide_tf_{load,read}() directly.

* Make ide_tf_{load,read}() static.

There should be no functional changes caused by this patch.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-28 23:44:40 +02:00
Harvey Harrison eb63963a55 ide: replace remaining __FUNCTION__ occurrences
__FUNCTION__ is gcc-specific, use __func__

[bart: fix checkpatch.pl errors in ide-lib.c and ppc/mpc8xx.c while at it]

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-26 22:25:20 +02:00
Bartlomiej Zolnierkiewicz ac95beedf8 ide: add struct ide_port_ops (take 2)
* Move hooks for port/host specific methods from ide_hwif_t to
  'struct ide_port_ops'.

* Add 'const struct ide_port_ops *port_ops' to 'struct ide_port_info'
  and ide_hwif_t.

* Update host drivers and core code accordingly.

While at it:

* Rename ata66_*() cable detect functions to *_cable_detect() to match
  the standard naming. (Suggested by Sergei Shtylyov)

v2:
* Fix build for bast-ide. (Noticed by Andrew Morton)

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-26 22:25:14 +02:00
Bartlomiej Zolnierkiewicz 784506cbdd ide: sanitize handling of IDE_HFLAG_NO_SET_MODE host flag
* Check for IDE_HFLAG_NO_SET_MODE host flag in ide_set_pio(),
  ide_set_[pio,dma]_mode(), ide_set_xfer_rate() and set_pio_mode().

* Remove no longer needed IDE_HFLAG_NO_SET_MODE host flag checking
  from ide_tune_dma().

* Remove superfluous ->set_pio_mode checking from do_special().

This is a part of preparations for adding 'struct ide_port_ops'.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-26 17:36:43 +02:00
Bartlomiej Zolnierkiewicz 078fdf789c ide: remove PIO "downgrade" quirk
No need for it nowadays so remove quirk code from ide_get_best_pio_mode()
and IDE_HFLAG_PIO_DOWNGRADE host flag.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-26 17:36:36 +02:00
Bartlomiej Zolnierkiewicz 37ff9f3953 ide: remove commented out entries from ide_pio_blacklist[]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-03-22 16:40:20 +01:00
Bartlomiej Zolnierkiewicz 467390a2a5 ide: remove stale comment from ide-lib.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-11 00:32:15 +01:00
Bartlomiej Zolnierkiewicz 64a57fe439 ide: add ide_read_error() inline helper
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-06 02:57:51 +01:00
Bartlomiej Zolnierkiewicz 36501650ec ide: keep pointer to struct device instead of struct pci_dev in ide_hwif_t
Keep pointer to struct device instead of struct pci_dev in ide_hwif_t.

While on it:
* Use *dev->dma_mask instead of pci_dev->dma_mask in ide_toggle_bounce().

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-01 23:09:31 +01:00
Bartlomiej Zolnierkiewicz 7267c33774 ide: remove REQ_TYPE_ATA_CMD
Based on the earlier work by Tejun Heo.

All users are gone so we can finally remove it.

Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-26 20:13:13 +01:00
Bartlomiej Zolnierkiewicz 4db90a1452 ide: add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag
* Add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag and use it to decide
  what to do with transfer modes < XFER_PIO_0 in ide_set_xfer_rate().

* Set IDE_HFLAG_ABUSE_SET_DMA_MODE in host drivers that need it
  (aec62xx, amd74xx, cs5520, cs5535, hpt34x, hpt366, pdc202xx_old,
  serverworks, tc86c001 and via82cxxx) and cleanup ->set_dma_mode
  methods in host drivers that don't (IDE core code guarantees that
  ->set_dma_mode will be called only for modes which are present
  in SWDMA/MWDMA/UDMA masks).

While at it:

* Add IDE_HFLAGS_HPT34X/HPT3XX/PDC202XX/SVWKS define in
  hpt34x/hpt366/pdc202xx_old/serverworks host driver.

There should be no functionality changes caused by this patch.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-25 22:17:18 +01:00
Bartlomiej Zolnierkiewicz e62925dd26 ide: kill duplicate code in ide_dump_{ata,atapi}_status()
* Move the common code from ide_dump_{ata,atapi}_status() to
  ide_dump_status().

* ide_dump_{ata,atapi}_status() -> ide_dump_{ata,atapi}_error().

There should be no functionality changes caused by this patch.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-25 22:17:17 +01:00
Bartlomiej Zolnierkiewicz a501633c7d ide-disk: use ide_get_lba_addr()
* Export ide_get_lba_addr().

* Convert idedisk_{read_native,set}_max_address() to use ide_get_lba_addr().

* Remove incorrect comment from idedisk_read_native_max_address()
  (noticed by Sergei).

There should be no functionality changes caused by this patch.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-25 22:17:17 +01:00
Andrew Morton 1c904fcfbb ide: printk fix
power4:

drivers/ide/ide-lib.c: In function `ide_dump_sector':
drivers/ide/ide-lib.c:516: warning: long long unsigned int format, u64 arg (arg 2)

We don't know what type is used to implement u64 hence it must always be cast
when printed.

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-25 22:17:17 +01:00
Bartlomiej Zolnierkiewicz c2b57cdc1d ide: add ide_tf_read() helper
* Factor out code reading taskfile registers from ide_end_drive_cmd()
  to the new ide_tf_read() helper.

* Add IDE_TFLAG_IN_* taskfile flags to indicate the need to load
  particular IDE taskfile register in ide_tf_read().

* Update ide_end_drive_cmd() to set respective IDE_TFLAG_IN_* taksfile flags.

* Add ide_get_lba_addr() for getting LBA sector address from taskfile struct.

* Factor out code getting sector address from ide_dump_ata_status()
  to the new ide_dump_sector() function.

* Convert ide_dump_sector() to use ide_tf_read() and ide_get_lba_addr().

* Remove no longer needed ide_read_24().

The only change in functionality caused by this patch is that
ide_dump_ata_status() no longer prints "high"/"low" parts of LBA48
sector address (of course LBA48 sector address is still printed).

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-25 22:17:17 +01:00
Bartlomiej Zolnierkiewicz d32444771b ide: fix registers loading order in ide_dump_ata_status()
Fix registers loading order in ide_dump_ata_status()/ide_read_24().

Load registers in this order:
* IDE_SECTOR_REG
* IDE_LCYL_REG
* IDE_HCYL_REG
* IDE_SELECT_REG

It shouldn't affect anything (just a usual paranoia to separate changes
which change the way in which hardware is accessed from code cleanups).

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-25 22:17:17 +01:00
Bartlomiej Zolnierkiewicz 0e38a66a1e ide: remove atapi_error_t (take 2)
Remove atapi_error_t.

While at it:
* replace 'HWIF(drive)' by 'drive->hwif'

v2:
* Add {ILI,EOM,LFS}_ERR defines to <linux/hdreg.h>.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-25 22:17:12 +01:00
Bartlomiej Zolnierkiewicz 22c525b976 ide: remove ata_status_t and atapi_status_t
Remove ata_status_t (unused) and atapi_status_t.

While at it:
* replace 'HWIF(drive)' by 'drive->hwif' (or just 'hwif' where possible)

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-25 22:17:11 +01:00
Bartlomiej Zolnierkiewicz 29ed2a5f8c ide: remove REQ_TYPE_ATA_TASK
Based on the earlier work by Tejun Heo.

All users are gone so we can finally remove it.

Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-25 22:17:11 +01:00
Bartlomiej Zolnierkiewicz 650d841d9e ide: add struct ide_taskfile (take 2)
* Don't set write-only ide_task_t.hobRegister[6] and ide_task_t.hobRegister[7]
  in idedisk_set_max_address_ext().

* Add struct ide_taskfile and use it in ide_task_t instead of tfRegister[]
  and hobRegister[].

* Remove no longer needed IDE_CONTROL_OFFSET_HOB define.

* Add #ifndef/#endif __KERNEL__ around definitions of {task,hob}_struct_t.

While at it:

* Use ATA_LBA define for LBA bit (0x40) as suggested by Tejun Heo.

v2:
* Add missing newlines. (Noticed by Sergei)

* Use ~ATA_LBA instead of 0xBF. (Noticed by Sergei)

* Use unnamed unions for error/feature and status/command.
  (Suggested by Sergei).

There should be no functionality changes caused by this patch.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-25 22:17:06 +01:00
Bartlomiej Zolnierkiewicz 3ab7efe8e2 ide: DMA reporting and validity checking fixes (take 3)
* ide_xfer_verbose() fixups:
  - beautify returned mode names
  - fix PIO5 reporting
  - make it return 'const char *'

* Change printk() level from KERN_DEBUG to KERN_INFO in ide_find_dma_mode().

* Add ide_id_dma_bug() helper based on ide_dma_verbose() to check for invalid
  DMA info in identify block.

* Use ide_id_dma_bug() in ide_tune_dma() and ide_driveid_update().

  As a result DMA won't be tuned or will be disabled after tuning if device
  reports inconsistent info about enabled DMA mode (ide_dma_verbose() does the
  same checks while the IDE device is probed by ide-{cd,disk} device driver).

* Remove no longer needed ide_dma_verbose().

This patch should fix the following problem with out-of-sync IDE messages
reported by Nick Warne:

       hdd: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache<7>hdd:
       skipping word 93 validity check
        , UDMA(66)

and later debugged by Mark Lord to be caused by:

        ide_dma_verbose()
                printk( ... "2048kB Cache");
        eighty_ninty_three()
                printk(KERN_DEBUG "%s: skipping word 93 validity check\n");
        ide_dma_verbose()
                printk(", UDMA(66)"

Please note that as a result ide-{cd,disk} device drivers won't report the
DMA speed used but this is intended since now DMA mode being used is always
reported by IDE core code.

v2:
* fixes suggested by Randy:
  - use KERN_CONT for printk()-s in ide-{cd,disk}.c
  - don't remove argument name from ide_xfer_verbose() declaration

v3:
* Remove incorrect check for (id->field_valid & 1) from ide_id_dma_bug()
  (spotted by Sergei).

* "XFER SLOW" -> "PIO SLOW" in ide_xfer_verbose() (suggested by Sergei).

* Fix ide_find_dma_mode() to report the correct mode ('mode' after being
  limited by 'req_mode').

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Nick Warne <nick@ukfsn.org>
Cc: Mark Lord <lkml@rtr.ca>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-12-12 23:31:58 +01:00
Bartlomiej Zolnierkiewicz 12eda14f89 ide: add missing HOB bit clearing to ide_dump_ata_status()
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-11-13 22:09:15 +01:00
Bartlomiej Zolnierkiewicz 65c9cd23ca ide: remove ide_use_fast_pio()
Remove ide_use_fast_pio() and just re-tune PIO unconditionally if DMA tuning
has failed in ->ide_dma_check.  All host drivers using ide_use_fast_pio() set
drive->autotune so PIO is always tuned anyway and in some cases we _really_
need to re-tune PIO because PIO and DMA timings are shared.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-16 22:29:54 +02:00
Bartlomiej Zolnierkiewicz 88b2b32bab ide: move ide_config_drive_speed() calls to upper layers (take 2)
* Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.

* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program 
  the host for the transfer mode after programming the device.  Set it
  in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
  and via82cxxx host drivers.

* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
  skip programming of host/device for the transfer mode ("smart" hosts).
  Set it in it821x host driver and check it in ide_tune_dma().

* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
  direct ->set_pio_mode/->speedproc users to use these helpers.

* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
  methods to callers.

* Rename ->speedproc method to ->set_dma_mode, make it void and update
  all implementations accordingly.

* Update ide_set_xfer_rate() comments.

* Unexport ide_config_drive_speed().

v2:
* Fix issues noticed by Sergei:
  - export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
    to setting DMA modes from sc1200_set_pio_mode() to do_special()
  - check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
  - check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
  - check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
  - return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
  - don't set ->set_{pio,dma}_mode on it821x in "smart" mode
  - fix build problem in pmac.c
  - minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
  - improve patch description

Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
  PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
  the device (not really an issue since 0x00 is not supported correctly by
  any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-13 17:47:51 +02:00
Bartlomiej Zolnierkiewicz 8f4dd2e426 ide: use only ->set_pio_mode method for programming PIO modes (take 2)
Use ->set_pio_mode method to program PIO modes in ide_set_xfer_rate()
(the only place which used ->speedproc to program PIO modes) and remove
handling of PIO modes from all ->speedproc implementations.

v2:
* Fix pmac_ide_tune_chipset() comment.

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-11 23:54:02 +02:00
Bartlomiej Zolnierkiewicz 26bcb879c0 ide: add ide_set{_max}_pio() (take 4)
* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
  and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.

* Add set_pio_mode_abuse() for checking if host driver has a non-standard
  ->tuneproc() implementation and use it in do_special().

* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
  the maximum PIO mode supported by the host), also add ide_set_max_pio()
  wrapper for ide_set_pio() to use for auto-tuning.  Convert users of
  ->tuneproc to use ide_set{_max}_pio() where possible.  This leaves only
  do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
  a direct users of ->tuneproc.

* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
  reporting PIO mode selected from ->tuneproc implementations.

* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.

* Remove stale comment from ide_config_drive_speed().

v2:
* Fix "ata_" prefix (Noticed by Jeff).

v3:
* Minor cleanups/fixups per Sergei's suggestions.

v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
  (Noticed by Andrew Morton).

* Improve some ->set_pio_mode comments.

Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-11 23:54:00 +02:00
Bartlomiej Zolnierkiewicz f212ff28f0 ide: move ide_rate_filter() calls to the upper layer (take 2)
* Move ide_rate_filter() calls from host drivers to IDE core.

* Make ide_rate_filter() static.

* Make 'speed' argument of ->speedproc const.

v2:
* Fix it8213_tune_chipset() comment.

There should be no functionality changes caused by this patch.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-11 23:53:59 +02:00
Bartlomiej Zolnierkiewicz 7670df73fb ide: mode limiting fixes for user requested speed changes
* Add an extra argument to ide_max_dma_mode() for passing requested transfer
  mode.  Use it as an upper limit when finding the best DMA for device/host.

* Rename ide_max_dma_mode() to ide_find_dma_mode() and at the same time add
  ide_max_dma_mode() wrapper which passes XFER_UDMA_6 as a requested mode to
  ide_find_dma_mode().  Also add inline ide_find_dma_mode() version for
  CONFIG_BLK_DEV_IDEDMA=n case.

* Pass requested transfer mode from ide_find_dma_mode() to ide_get_mode_mask()
  to avoid false warning from eighty_ninty_three().

* Use ide_find_dma_mode() to limit the user requested transfer mode in
  ide_rate_filter().  Also limit the requested mode by host max PIO mode.


Above changes make ide_rate_filter() to:

* Clip desired transfer mode down if it is invalid (values 0x0F, 0x13-0x19
  and 0x25-0x39, values > 0x46 were already clipped down, same for values
  0x25-0x39 but iff UDMA was not supported by the host).

* Clip desired transfer mode down if it is currently unsupported by IDE core
  (PIO6 and MWDMA3-4, the latter were already clipped down but iff UDMA was
  not supported by the host).

* Clip desired transfer mode down according to the host capabilities
  (UDMA modes were already clipped down but MWDMA/SWDMA/PIO weren't,
  also ->atapi_dma flag was not respected).

* Clip desired transfer mode down according to the device capabilities
  (except PIO modes for now which require mode work) - shouldn't be a
  problem since ide_set_xfer_rate() is called _after_ device has accepted
  given transfer mode.

and also result in a number of host driver specific bugfixes:

* icside
  - clip unsupported PIO5 mode down
  - fix unsupported/invalid modes being set in drive->current_speed

* ide-cris
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices
  - fix BUG() on unsupported/invalid modes

* au1xxx-ide
  - clip unsupported PIO5, SWDMA0-2 and MWDMA0-2
    (if BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA=n) modes down

* aec62xx
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices
  - fix 0x00 being programmed as PIO timing for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* alim15x3
  - clip DMA modes down for ATAPI devices (chipset revision == 0x20 only)
  - fix theoretical OOPS for 0x0F mode
  - fix unsupported/invalid modes being set on the device

* amd74xx
  - clip unsupported SWDMA0-2 (on COBRA_7401 revs <= 7) modes down
  - fix random PIO timings being set for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* atiixp
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix cached MWDMA mode being cleared for unsupported/invalid modes
  - fix PIO{0,2} timings being programmed for unsupported/invalid modes
  - fix theoretical OOPS for PIO5-6 and 0x0F modes
  - fix unsupported/invalid modes being set on the device

* cmd64x
  - clip unsupported SWDMA0-2 modes down

* cs5530
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device
  - fix BUG() on unsupported/invalid modes
    (which happened if the device accepted the setting)

* cs5535
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device
  - fix theoretical OOPS for PIO5-6 and 0x0F modes

* hpt34x
  - clip DMA modes down for ATAPI devices
  - fix invalid timings being programmed for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* hpt366
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix PIO0 timings being programmed for unsupported/invalid modes
  - fix DMA timings being cleared for MWDMA3-4 and 0x25-0x39 modes
  - fix unsupported/invalid modes being set on the device

* it8213
  - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down

* it821x
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices
    (chipset in smart mode and revision 0x10 in pass-through mode)

* jmicron
  - clip unsupported SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device

* pdc202xx_new
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device

* pdc202xx_old
  - clip unsupported PIO5 mode down
  - fix incorrect timings being set for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* piix
  - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down

* sc1200
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device
  - fix BUG() on unsupported/invalid modes
    (which happened if the device accepted the setting)

* scc_pata
  - clip unsupported PIO5, SWDMA0-2 and MWDMA0-2 modes down

* serverworks
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix DMA/UDMA timings/settings being cleared for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* siimage
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices (SATA chipsets)

* sis5513
  - clip unsupported PIO5 mode down
  - fix BUG() on unsupported/invalid modes

* sl82c105
  - clip unsupported SWDMA0-2 modes down

* slc90e66
  - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down

* tc86c001
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix PIO0 timings being programmed for PIO5/0x0F/SWDMA0-2/0x13-0x19 modes
  - fix invalid 0x00 DMA timing being programmed for MWDMA3-4/0x25-0x39 modes
  - fix unsupported/invalid modes being set on the device

* triflex
  - clip unsupported PIO5 mode down

* via82cxxx
  - fix random PIO timings being set for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* pmac
  - clip unsupported PIO5 and SWDMA0-2 modes down

* cmd640/ht6560b
  - clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
  - fix PIO5 being clipped to PIO4 (if CONFIG_BLK_DEV_IDEDMA=n)

* opti621
  - clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
  - clip unsupported PIO4 to PIO3 (if CONFIG_BLK_DEV_IDEDMA=n)


While at it:

* Use ide_rate_filter() in cs5520.c::cs5520_tune_chipset().

* Remove no longer needed checks from hpt366.c::hpt3{6,7}x_tune_chipset().

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-10-11 23:53:59 +02:00
Bartlomiej Zolnierkiewicz 6a824c92db ide: remove ide_find_best_pio_mode()
* Add ->host_flags to ide_hwif_t to store ide_pci_device_t.host_flags,
  assign it in setup-pci.c:ide_pci_setup_ports().

* Add IDE_HFLAG_PIO_NO_{BLACKLIST,DOWNGRADE} to ide_pci_device_t.host_flags
  and teach ide_get_best_pio_mode() about them.  Also remove needless
  !drive->id check while at it (drive->id is always present).

* Convert amd74xx, via82cxxx and ide-timing.h to use ide_get_best_pio_mode()
  and then remove no longer needed ide_find_best_pio_mode().

There should be no functionality changes caused by this patch.

Acked-by: Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:58 +02:00
Bartlomiej Zolnierkiewicz 2134758d2a ide: drop "PIO data" argument from ide_get_best_pio_mode()
* Drop no longer needed "PIO data" argument from ide_get_best_pio_mode()
  and convert all users accordingly.

* Remove no longer needed ide_pio_data_t.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:58 +02:00
Bartlomiej Zolnierkiewicz 7dd00083b1 ide: add ide_pio_cycle_time() helper (take 2)
* Add ide_pio_cycle_time() helper.

* Use it in ali14xx/ht6560b/qd65xx/cmd64{0,x}/sl82c105 and pmac host drivers
  (previously cycle time given by the device was only used for "pio" == 255).

* Remove no longer needed ide_pio_data_t.cycle_time field.

v2:
* Fix "ata_" prefix (Noticed by Jeff).

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:56 +02:00
Bartlomiej Zolnierkiewicz 2229833c13 ide: add ide_dev_has_iordy() helper (take 4)
* Add ide_dev_has_iordy() helper and use it sl82c105 host driver.

* Remove no longer needed ide_pio_data_t.use_iordy field.

v2/v3:
* Fix issues noticed by Sergei:
  - correct patch description
  - fix comment in ide_get_best_pio_mode()

v4:
* Fix "ata_" prefix (Noticed by Jeff).

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:55 +02:00
Bartlomiej Zolnierkiewicz 342cdb6d47 ide: make ide_get_best_pio_mode() print info if overriding PIO mode
* Print info about overriding PIO mode in ide_get_best_pio_mode().

* Remove info about overriding PIO mode from cmd64{0,x} host drivers.

* Remove no longer needed ide_pio_data_t.overridden field.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:55 +02:00
Bartlomiej Zolnierkiewicz 4728d546d7 ide: remove ide_dma_enable()
* check ->speedproc return value in ide_tune_dma()
* use ide_tune_dma() in cmd64x/cs5530/sc1200/siimage/sl82c105/scc_pata drivers
* remove no longer needed ide_dma_enable()

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:46 +02:00
Bartlomiej Zolnierkiewicz 7f8f48af08 ide: cable detection fixes (take 2)
Tejun's recent eighty_ninty_three() fix has inspired me to do more thorough
review of the cable detection code...

* print user-friendly warning about limiting the maximum transfer speed
  to UDMA33 (and the reason behind it) when 80-wire cable is not detected,
  also while at it cleanup eighty_ninty_three() a bit

* use eighty_ninty_three() in ide_ata66_check(), this actually fixes 3 bugs:
  - bit 14 (word 93 validity check) == 1 && bit 13 (80-wire cable test) == 1
    were used as 80-wire cable present test for CONFIG_IDEDMA_IVB=n case
    (please see FIXME comment in eighty_ninty_three() for more details)
  - CONFIG_IDEDMA_IVB=y/n cases were interchanged
  - check for SATA devices was missing

* remove private cable warnings from pdc_202xx{old,new} drivers now that core
  code provides this functionality (plus, in pdc202xx_new case the test could
  give false warnings for ATAPI devices because pdc202xx_new driver doesn't
  even support ATAPI DMA)

Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:10 +02:00
Bartlomiej Zolnierkiewicz 2d5eaa6dd7 ide: rework the code for selecting the best DMA transfer mode (v3)
Depends on the "ide: fix UDMA/MWDMA/SWDMA masks" patch.

* add ide_hwif_t.udma_filter hook for filtering UDMA mask
  (use it in alim15x3, hpt366, siimage and serverworks drivers)
* add ide_max_dma_mode() for finding best DMA mode for the device
  (loosely based on some older libata-core.c code)
* convert ide_dma_speed() users to use ide_max_dma_mode()
* make ide_rate_filter() take "ide_drive_t *drive" as an argument instead
  of "u8 mode" and teach it to how to use UDMA mask to do filtering
* use ide_rate_filter() in hpt366 driver
* remove no longer needed ide_dma_speed() and *_ratemask()
* unexport eighty_ninty_three()

v2:
* rename ->filter_udma_mask to ->udma_filter
  [ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]

v3:
* updated for scc_pata driver (fixes XFER_UDMA_6 filtering for user-space
  originated transfer mode change requests when 100MHz clock is used)

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-10 00:01:08 +02:00
Sergei Shtylyov 81d368e0e2 ide: ide_get_best_pio_mode() returns incorrect IORDY setting (take 2)
The function ide_get_best_pio_mode() fails to return the correct IORDY setting
for the explicitly specified modes -- fix this along with the heading comment,
and also remove the long commented out code.

Also, while at it, correct the misliading comment about the PIO cycle time in
<linux/ide.h> -- it actually consists of only the active and recovery periods,
with only some chips also including the address setup time into equation...

[ bart: sl82c105 seems to be currently the only driver affected by this fix ]

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-03-03 17:48:53 +01:00
Bartlomiej Zolnierkiewicz 7569e8dc22 ide: add ide_use_fast_pio() helper (v3)
* add ide_use_fast_pio() helper for use by host drivers

* add DMA capability and hwif->autodma checks to ide_use_dma()

  - au1xxx-ide/it8213/it821x drivers didn't check for (id->capability & 1)

    [ for the IT8211/2 in SMART mode this check shouldn't be made but since
      in it821x_fixups() we set DMA bit explicitly:

               if(strstr(id->model, "Integrated Technology Express")) {
                       /* In raid mode the ident block is slightly buggy
                          We need to set the bits so that the IDE layer knows
                          LBA28. LBA48 and DMA ar valid */
                       id->capability |= 3;            /* LBA28, DMA */

       we are better off using generic helper if we can ]

  - ide-cris driver didn't set ->autodma

    [ before the patch hwif->autodma was only checked in the chipset specific
      hwif->ide_dma_check implementations, for ide-cris it is cris_dma_check()
      function so there no behavior change here ]

v2:
* updated patch description (thanks to Alan Cox for the feedback)

v3:
* updated for scc_pata driver

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-02-17 02:40:25 +01:00
Bartlomiej Zolnierkiewicz 056a697b73 ide: unexport ide_set_xfer_rate() (v2)
In cmd64x, siimage and scc_pata drivers:
* don't set drive->init_speed as it should be already
  set by successful execution of ide_set_xfer_rate()
* use hwif->speedproc functions directly

Above changes allows removal of EXPORT_SYMBOL_GPL(ide_set_xfer_rate).

v2:
* updated for scc_pata driver

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-02-17 02:40:24 +01:00