When trying to associate to an AP support 180 or 80+80 MHz on 6 GHz with a
STA that only has 80 Mhz support the cf2 field inside the chandef will get
set causing the association to fail when trying to validate the chandef.
Fix this by checking the support flags prior to setting cf2.
Fixes: 57fa5e85d5 ("mac80211: determine chandef from HE 6 GHz operation")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200918115304.1135693-1-john@phrozen.org
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When converting from struct ieee80211_tx_rate to ieee80211_rx_status,
there was one check missing to fill in the bandwidth for 160 MHz
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20200915085945.3782-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The unit of the return value of ieee80211_get_rate_duration is nanoseconds, not
microseconds. Adjust the duration checks to account for that.
For higher data rates, allow larger estimated aggregation sizes, and add some
values for HE as well, which can use much larger aggregates.
Since small packets with high data rates can now lead to duration values too
small for info->tx_time_est, return a minimum of 4us.
Fixes: f01cfbaf9b ("mac80211: improve AQL aggregation estimation for low data rates")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20200915085945.3782-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When running a large number of packets per second with a high data rate
and long A-MPDUs, the packet loss threshold can be reached very quickly
when the link conditions change. This frequently shows up as spurious
disconnects.
Mitigate false positives by using a similar logic for regular stations
as the one being used for TDLS, though with a more aggressive timeout.
Packet loss events are only reported if no ACK was received for a second.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200808172542.41628-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Links with low data rates use much smaller aggregates and are much more
sensitive to latency added by bufferbloat.
Tune the assumed aggregation length based on the tx rate duration.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20200821163045.62140-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will be used to enhance AQL estimated aggregation length
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20200821163045.62140-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since ieee80211_tx_info does not have enough room to encode HE rates, HE
drivers use status->rate to provide rate info.
Store it in struct sta_info and use it for AQL.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20200821163045.62140-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As said by Linus:
A symmetric naming is only helpful if it implies symmetries in use.
Otherwise it's actively misleading.
In "kzalloc()", the z is meaningful and an important part of what the
caller wants.
In "kzfree()", the z is actively detrimental, because maybe in the
future we really _might_ want to use that "memfill(0xdeadbeef)" or
something. The "zero" part of the interface isn't even _relevant_.
The main reason that kzfree() exists is to clear sensitive information
that should not be leaked to other future users of the same memory
objects.
Rename kzfree() to kfree_sensitive() to follow the example of the recently
added kvfree_sensitive() and make the intention of the API more explicit.
In addition, memzero_explicit() is used to clear the memory to make sure
that it won't get optimized away by the compiler.
The renaming is done by using the command sequence:
git grep -w --name-only kzfree |\
xargs sed -i 's/kzfree/kfree_sensitive/'
followed by some editing of the kfree_sensitive() kerneldoc and adding
a kzfree backward compatibility macro in slab.h.
[akpm@linux-foundation.org: fs/crypto/inline_crypt.c needs linux/slab.h]
[akpm@linux-foundation.org: fix fs/crypto/inline_crypt.c some more]
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Joe Perches <joe@perches.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: "Jason A . Donenfeld" <Jason@zx2c4.com>
Link: http://lkml.kernel.org/r/20200616154311.12314-3-longman@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mac80211.h says: Beacon filter support is advertised with the
IEEE80211_VIF_BEACON_FILTER interface capability. The driver needs to
enable beacon filter support whenever power save is enabled, that is
IEEE80211_CONF_PS is set. When power save is enabled, the stack will
not check for beacon loss and the driver needs to notify about loss
of beacons with ieee80211_beacon_loss().
Some controllers may want to dynamically enable the beacon filter
capabilities on power save entry (CONF_PS) and disable it on exit.
This is the case for the wcn36xx driver which only supports beacon
filtering in PS mode (no CONNECTION_MONITOR support).
When the mac80211 beacon monitor timer expires, the beacon filter
flag must be checked again in case it as been changed in between
(e.g. vif moved to PS mode).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1592471863-31402-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sparse showed up with the following error.
net/mac80211/agg-rx.c:480:43: warning: Using plain integer as NULL pointer
Fixes: 2ab4587675 (mac80211: add support for the ADDBA extension element)
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200803084540.179908-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SAE authentication has been extended with H2E (IEEE 802.11 REVmd) and PK
(WFA) options. Those extensions use special status code values in the
SAE commit messages (Authentication frame with transaction sequence
number 1) to identify which extension is in use. mac80211 was
interpreting those new values as the AP denying authentication and that
resulted in failure to complete SAE authentication in some cases.
Fix this by adding exceptions for the new status code values 126 and
127.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200731183830.18735-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ben Greear has repeatedly reported in the past (for a few years
probably) that this triggers repeatedly in certain scenarios.
Make this a macro so that each callsite can trigger the warning
only once - that will still give us an idea of what's going on
and what paths can reach it, but avoids being too noisy.
Link: https://lore.kernel.org/r/20200730155212.06fd3a95dbfb.I0b16829aabfaf5f642bce401502a29d16e2dd444@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is in fact 'disabled' in the spec, but there it's in a
place where that actually makes sense. In our internal data
structures, it doesn't really make sense, and in fact the
previous commit just fixed a bug in that area.
Make this safer by inverting the polarity from 'disabled' to
'enabled'.
Link: https://lore.kernel.org/r/20200730130051.5d8399545bd9.Ie62fdcd1a6cd9c969315bc124084a494ca6c8df3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be used to run mac80211 rx processing on a batch of frames in NAPI
poll before passing them to the network stack in a large batch.
This can improve icache footprint, or it can be used to pass frames via
netif_receive_skb_list.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200726110611.46886-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Already parse the radiotap header in ieee80211_monitor_select_queue.
In a subsequent commit this will allow us to add a radiotap flag that
influences the queue on which injected packets will be sent.
This also fixes the incomplete validation of the injected frame in
ieee80211_monitor_select_queue: currently an out of bounds memory
access may occur in in the called function ieee80211_select_queue_80211
if the 802.11 header is too small.
Note that in ieee80211_monitor_start_xmit the radiotap header is parsed
again, which is necessairy because ieee80211_monitor_select_queue is not
always called beforehand.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-6-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the IEEE80211_TX_CTRL_NO_SEQNO flag in ieee80211_tx_info to mark
probe requests whose sequence number must not be overwritten. This
provides consistency with the radiotap flag that can be set to indicate
that the sequence number of an injected frame should not be overwritten.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-4-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check if the Tx control flag is set to prevent sequence number overwrites,
and if so, do not assign a new sequence number to the transmitted frame.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-3-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The radiotap specification contains a flag to indicate that the sequence
number of an injected frame should not be overwritten. Parse this flag
and define and set a corresponding Tx control flag.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-2-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_tx_dequeue there is a check to see if the dequeued frame
is allowed in the current state. Injected frames that are normally
not allowed are being be dropped here. Fix this by checking if a
frame was injected and if so always allowing it.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-1-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding bss-color configuration is only valid in HE mode.
Earlier we have enabled it by default, irrespective of
capabilities/mode. Fix that.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Link: https://lore.kernel.org/r/1594262781-21444-1-git-send-email-ppranees@codeaurora.org
[fix up commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
AQL does not take into account that most HT/VHT/HE traffic is A-MPDU aggregated.
Because of that, the per-packet airtime overhead is vastly overestimated.
Improve it by assuming an average aggregation length of 16 for non-legacy
traffic if not using the VO AC queue.
This should improve performance with high data rates, especially with multiple
stations
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200724182816.18678-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Besides information about num of peerings and gate connectivity,
the mesh formation byte also contains a flag for authentication
server connectivity, that currently cannot be set in the mesh conf.
This patch adds this capability, which is necessary to implement
802.1X authentication in mesh mode.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200611140238.427461-1-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, before being able to forward a packet between two 802.11s
nodes, both a PLINK handshake is performed upon receiving a beacon and
then later a PREQ/PREP exchange for path discovery is performed on
demand upon receiving a data frame to forward.
When running a mesh protocol on top of an 802.11s interface, like
batman-adv, we do not need the multi-hop mesh routing capabilities of
802.11s and usually set mesh_fwding=0. However, even with mesh_fwding=0
the PREQ/PREP path discovery is still performed on demand. Even though
in this scenario the next hop PREQ/PREP will determine is always the
direct 11s neighbor node.
The new mesh_nolearn parameter allows to skip the PREQ/PREP exchange in
this scenario, leading to a reduced delay, reduced packet buffering and
simplifies HWMP in general.
mesh_nolearn is still rather conservative in that if the packet destination
is not a direct 11s neighbor, it will fall back to PREQ/PREP path
discovery.
For normal, multi-hop 802.11s mesh routing it is usually not advisable
to enable mesh_nolearn as a transmission to a direct but distant neighbor
might be worse than reaching that same node via a more robust /
higher throughput etc. multi-hop path.
Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Link: https://lore.kernel.org/r/20200617073034.26149-1-linus.luessing@c0d3.blue
[fix nl80211 policy to range 0/1 only]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently rates_idx is being initialized with the value -1 and this
value is never read so the initialization is redundant and can be
removed. The next time the variable is used it is assigned a value
that is returned a few statements later. Just return i - 1 and
remove the need for rates_idx.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200722153830.959010-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This warning can trigger if there is a mismatch between frames that were
sent with the sta pointer set vs tx status frames reported for the sta address.
This can happen due to race conditions on re-creating stations, or even
in the case of .sta_add/remove being used instead of .sta_state, which can cause
frames to be sent to a station that has not been uploaded yet.
If there is an actual underflow issue, it should show up in the device airtime
warning below, so it is better to remove this one.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200725084533.13829-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allocated ack_frame id from local->ack_status_frames is not really
stored in the tx_info for 802.3 Tx path. Due to this, tx ack status
is not reported and ack_frame id is not freed for the buffers requiring
tx ack status. Also move the memset to 0 of tx_info before
IEEE80211_TX_CTL_REQ_TX_STATUS flag assignment.
Fixes: 50ff477a86 ("mac80211: add 802.11 encapsulation offloading support")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Link: https://lore.kernel.org/r/1595427617-1713-1-git-send-email-vthiagar@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The commit 24a2042cb2 ("mac80211: add HE 6 GHz Band Capability
element") failed to check device capability before adding HE 6 GHz
capability element. Below warning is reported in 11ac device in mesh.
Fix that by checking device capability at HE 6 GHz cap IE addition
in mesh beacon and association request.
WARNING: CPU: 1 PID: 1897 at net/mac80211/util.c:2878
ieee80211_ie_build_he_6ghz_cap+0x149/0x150 [mac80211]
[ 3138.720358] Call Trace:
[ 3138.720361] ieee80211_mesh_build_beacon+0x462/0x530 [mac80211]
[ 3138.720363] ieee80211_start_mesh+0xa8/0xf0 [mac80211]
[ 3138.720365] __cfg80211_join_mesh+0x122/0x3e0 [cfg80211]
[ 3138.720368] nl80211_join_mesh+0x3d3/0x510 [cfg80211]
Fixes: 24a2042cb2 ("mac80211: add HE 6 GHz Band Capability element")
Reported-by: Markus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Link: https://lore.kernel.org/r/1593656424-18240-1-git-send-email-rmanohar@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Simple fixes which require no deep knowledge of the code.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch, eapol frames cannot be received in mesh
mode, when 802.1X should be used. Initially only a MGTK is
defined, which is found and set as rx->key, when there are
no other keys set. ieee80211_drop_unencrypted would then
drop these eapol frames, as they are data frames without
encryption and there exists some rx->key.
Fix this by differentiating between mesh eapol frames and
other data frames with existing rx->key. Allow mesh mesh
eapol frames only if they are for our vif address.
With this patch in-place, ieee80211_rx_h_mesh_fwding continues
after the ieee80211_drop_unencrypted check and notices, that
these eapol frames have to be delivered locally, as they should.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200625104214.50319-1-markus.theil@tu-ilmenau.de
[small code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using 802.1X over mesh networks, at first an ordinary
mesh peering is established, then the 802.1X EAPOL dialog
happens, afterwards an authenticated mesh peering exchange
(AMPE) happens, finally the peering is complete and we can
set the STA authorized flag.
As 802.1X is an intermediate step here and key material is
not yet exchanged for stations we have to skip mesh path lookup
for these EAPOL frames. Otherwise the already configure mesh
group encryption key would be used to send a mesh path request
which no one can decipher, because we didn't already establish
key material on both peers, like with SAE and directly using AMPE.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200617082637.22670-2-markus.theil@tu-ilmenau.de
[remove pointless braces, remove unnecessary local variable,
the list can only process one such frame (or its fragments)]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Broadcast pkts like arp are getting dropped in 'ieee80211_8023_xmit'.
Fix this by replacing is_valid_ether_addr api with is_zero_ether_addr.
Fixes: 50ff477a86 ("mac80211: add 802.11 encapsulation offloading support")
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Link: https://lore.kernel.org/r/1591697754-4975-1-git-send-email-seevalam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The initial control port tx status patch assumed, that
we have IEEE 802.11 frames, but actually ethernet frames
are stored in the ack skb. Fix this by checking for the
correct ethertype and skb protocol 802.3.
Also allow tx status reports for ETH_P_PREAUTH, as preauth
frames can also be send over the nl80211 control port.
Fixes: a7528198ad ("mac80211: support control port TX status reporting")
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20200622123542.173695-1-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
1) Fix cfg80211 deadlock, from Johannes Berg.
2) RXRPC fails to send norigications, from David Howells.
3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
Geliang Tang.
4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.
5) The ucc_geth driver needs __netdev_watchdog_up exported, from
Valentin Longchamp.
6) Fix hashtable memory leak in dccp, from Wang Hai.
7) Fix how nexthops are marked as FDB nexthops, from David Ahern.
8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.
9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.
10) Fix link speed reporting in iavf driver, from Brett Creeley.
11) When a channel is used for XSK and then reused again later for XSK,
we forget to clear out the relevant data structures in mlx5 which
causes all kinds of problems. Fix from Maxim Mikityanskiy.
12) Fix memory leak in genetlink, from Cong Wang.
13) Disallow sockmap attachments to UDP sockets, it simply won't work.
From Lorenz Bauer.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: ethernet: ti: ale: fix allmulti for nu type ale
net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
net: atm: Remove the error message according to the atomic context
bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
libbpf: Support pre-initializing .bss global variables
tools/bpftool: Fix skeleton codegen
bpf: Fix memlock accounting for sock_hash
bpf: sockmap: Don't attach programs to UDP sockets
bpf: tcp: Recv() should return 0 when the peer socket is closed
ibmvnic: Flush existing work items before device removal
genetlink: clean up family attributes allocations
net: ipa: header pad field only valid for AP->modem endpoint
net: ipa: program upper nibbles of sequencer type
net: ipa: fix modem LAN RX endpoint id
net: ipa: program metadata mask differently
ionic: add pcie_print_link_status
rxrpc: Fix race between incoming ACK parser and retransmitter
net/mlx5: E-Switch, Fix some error pointer dereferences
net/mlx5: Don't fail driver on failure to create debugfs
net/mlx5e: CT: Fix ipv6 nat header rewrite actions
...
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
In the files:
- net/mac80211/rx.c
- net/wireless/Kconfig
the wiki url is still the old "wireless.kernel.org"
instead of the new "wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Link: https://lore.kernel.org/r/20200605154112.16277-10-f.suligoi@asem.it
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Dan points out that if ieee80211_chandef_he_6ghz_oper() succeeds,
we don't initialize 'ret'. Initialize it to 0 in this case, since
everything went fine and nothing has to be disabled.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 57fa5e85d5 ("mac80211: determine chandef from HE 6 GHz operation")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200603111500.bd2a5ff37b83.I2c3f338ce343b581db493eb9a0d988d1b626c8fb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John Crispin
Felix Fietkau
Wen Gong
Aloka Dixit
Waiman Long
Loic Poulain
Johannes Berg
Miaohe Lin
Jouni Malinen
David S. Miller
Mathy Vanhoef
P Praneesh
Markus Theil
Linus Lüssing
Gustavo A. R. Silva
Colin Ian King
Thomas Pedersen
Vasanthakumar Thiagarajan
Remi Pommarel
Rajkumar Manoharan
Andrew Lunn
Seevalamuthu Mariappan
Pavel Machek
Linus Torvalds
Masahiro Yamada
Flavio Suligoi