Граф коммитов

48 Коммитов

Автор SHA1 Сообщение Дата
Luca Ceresoli a26d84633c rtc: max77686: Rename day-of-month defines
RTC_DATE and REG_RTC_DATE are used for the registers holding the day of
month. Rename these constants to mean what they mean.

Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2022-03-07 13:54:24 +00:00
Krzysztof Kozlowski 215e50b086 mfd: max77686: Do not enforce (incorrect) interrupt trigger type
Interrupt line can be configured on different hardware in different way,
even inverted.  Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.

The Maxim 77686 datasheet describes the interrupt line as active low
with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.

The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races.  With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210602110445.33536-2-krzysztof.kozlowski@canonical.com
2021-11-05 14:40:06 +00:00
Krzysztof Kozlowski 608a475857 mfd: max77686: Drop of_match_ptr from of_device_id table
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here).  This fixes
compile warning (!CONFIG_OF on x86_64):

  drivers/mfd/max77686.c:148:34: warning: ‘max77686_pmic_dt_match’ defined but not used [-Wunused-const-variable=]

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2020-11-27 08:02:19 +00:00
Krzysztof Kozlowski d7d8d7a240 mfd: maxim: Add SPDX license identifiers
Replace GPL v2.0+ license statements with SPDX license identifiers.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2018-10-23 08:58:34 +01:00
Javier Martinez Canillas 644b2ee06d mfd: max77686: Remove I2C device ID table
The driver is only used in DT platforms so there's no need to
have an i2c_device_id table.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-02-13 09:29:43 +00:00
Javier Martinez Canillas be1bb2355b mfd: max77686: Use the struct i2c_driver .probe_new instead of .probe
If a driver is only used in DT platforms, there's no need to get the
i2c_device_id as an argument of the probe function. Since this data
can be get from the matching of_device_id.

There's a temporary .probe_new field in struct i2c_driver that can be
used as probe callback for the case when i2c_device_id won't be used.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-02-13 09:29:43 +00:00
Javier Martinez Canillas 68e61f75ab mfd: max77686: Use of_device_get_match_data() helper
Use the generic helper to get the matched of_device_id .data, instead of
open coding it.

The driver was checking if matching the OF node with the driver's OF table
was failing, but this doesn't make too much sense since this can't happen
in practice. The fact the probe function was called, means OF registered a
device with a valid compatible string so a of_device_get_match_data() call
will always succeed. So just remove this unneeded check.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-02-13 09:29:43 +00:00
Javier Martinez Canillas 17ee971f03 mfd: max77686: Don't attempt to get i2c_device_id .data
The driver is only used in platforms that have DT support so always the
I2C device .data will be get from the matched OF node and never will be
from the I2C device ID table.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-02-13 09:29:43 +00:00
Laxman Dewangan 1a5422c9e5 mfd: max77686: Use devm_mfd_add_devices and devm_regmap_add_irq_chip
Use devm_mfd_add_devices() for adding MFD child devices and
devm_regmap_add_irq_chip() for IRQ chip registration.

This reduces the error code path and .remove callback for removing
MFD child devices and deleting IRQ chip data.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-05-09 13:27:20 +01:00
Javier Martinez Canillas 8a0aee4a7c mfd: max77686: Use module_i2c_driver() instead of subsys initcall
The driver's init and exit function don't do anything besides adding and
deleting the I2C driver so the module_i2c_driver() macro could be used.

Currently is not being used because the driver is initialized at subsys
initcall level, claiming that this is done to allow consumers devices to
use the resources provided by this driver. But dependencies are in DT so
manual ordering of init calls is not necessary any more.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-04-19 07:59:28 +01:00
Krzysztof Kozlowski 630fd98c0a mfd: max77686/max77693: Fix misspelled Samsung address
Correct smasung.com into samsung.com.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-04-19 07:59:14 +01:00
Linus Torvalds 12e7b0a627 - New Drivers
- Freescale Touch Screen ADC
    - X-Powers AXP PMIC with RSB
    - TI TPS65086 Power Management IC (PMIC)
  - New Device Support
    - Supply device PCI IDs for Intel Broxton
  - Fix-ups
    - Move to clkdev_create() API; intel_quark_i2c_gpio
    - Complete re-write of TI's TPS65912 Power Management IC (PMIC)
    - Remove unnecessary function argument; axp20x
    - Separate out bus related code; axp20x
    - Coding Style changes; axp20x
    - Allow more drivers to be compiled as modules
    - Work around false positive 'used uninitialised' warning; db8500-prcmu
  - Bug Fixes
    - Remove do_div(); fsl-imx25-gcq
    - Fix driver init when built-in; tps65010
    - Fix clock-unregister leak; intel-lpss
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJW6+LJAAoJEFGvii+H/Hdh8kQP/2AKYzPZiw9fhLufsDPvXO5m
 BVdLYVyA11oQjQk7/Bh+5Rjz8mR5Tfv4uAJUReC3FOIfC/oJNBfBxYJLDV/P8S0/
 KaCEaZrpNmecKrsy+TjmFYtcRa51THAdjlWEUKRks/ZBjwP4YsNnh5reWe+wB7bS
 NFbCNhpXFvYXaDGH8MRhKqdChzZkxi+lgOBcFCKvUYO5/o6g/ZRUD/0TXUItJDwh
 F8ps5jImHC1imHeRIKWPNrrZqcYasKmObIhvOKMDcwNQPnjrAWq5QuFH4LFhGQ7d
 7NMQrBpaGvZyUNBVtL7ZF1xCJ68wAg/ZvZUkKVkax9ubLbSgf6VXYLQEbq+lyFn7
 H9A79xPAGN2nC9HsGnCqW0c0qgTOz0DIkbpuaxAGlzBt0zooc19i3cuUd7LX0NG8
 ttLaIP1hX6rgvXSFnF0Ihe3iN5A90LTT3ldbn3A8awyS42vEAbUVL9ivRL21BUbB
 ilSTO2W05a9HlIVe43o2euytaGvDYX7RbL/g3WcJLF1pA01RCIDQAI5usMpgF3bf
 fJ7cszll0OVTTb5UzbfrNsxAn4oNtbwMIspMMFe17pbmxqh+4oomM3CkuTrMVQfB
 pA7Uv0jh/mLCV6P52ZEsNiecn0/l0rID8d/DCHjunr2xBWIOrglzZ7n+vLTJMNJ6
 72GVBkYRMLbRm+eph1Tp
 =gTBA
 -----END PGP SIGNATURE-----

Merge tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull MFD updates from Lee Jones:
 "New Drivers:
   - Freescale Touch Screen ADC
   - X-Powers AXP PMIC with RSB
   - TI TPS65086 Power Management IC (PMIC)

  New Device Support:
   - Supply device PCI IDs for Intel Broxton

  Fix-ups:
   - Move to clkdev_create() API; intel_quark_i2c_gpio
   - Complete re-write of TI's TPS65912 Power Management IC (PMIC)
   - Remove unnecessary function argument; axp20x
   - Separate out bus related code; axp20x
   - Coding Style changes; axp20x
   - Allow more drivers to be compiled as modules
   - Work around false positive 'used uninitialised' warning; db8500-prcmu

  Bug Fixes:
   - Remove do_div(); fsl-imx25-gcq
   - Fix driver init when built-in; tps65010
   - Fix clock-unregister leak; intel-lpss"

* tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits)
  mfd: intel-lpss: Pass I2C configuration via properties on BXT
  mfd: imx6sx: Add PCIe register definitions for iomuxc gpr
  mfd: ipaq-micro: Use __maybe_unused to hide pm functions
  mfd: max77686: Add max77802 to I2C device ID table
  mfd: max77686: Export OF module alias information
  mfd: max77686: Allow driver to be built as a module
  mfd: stmpe: Add the proper PWM resources
  mfd: tps65090: Set regmap config reg counts properly
  mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled
  mfd: as3711: Set regmap config reg counts properly
  mfd: rc5t583: Set regmap config reg counts properly
  gpio: tps65086: Add GPO driver for the TPS65086 PMIC
  mfd: mt6397: Add platform device ID table
  mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists
  mfd: mt6397: Add MT6323 support to MT6397 driver
  mfd: mt6397: Add support for different Slave types
  mfd: mt6397: int_con and int_status may vary in location
  dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC
  mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists
  mfd: Add documentation for ACT8945A DT bindings
  ...
2016-03-18 10:15:11 -07:00
Javier Martinez Canillas 95a6f715bc mfd: max77686: Add max77802 to I2C device ID table
The max77686 MFD driver supports both the Maxim 77686 and Maxim 77802
PMICs but only the OF device table contains entries for both devices.

The max77802 entry is missing in the I2C device ID table which isn't
a problem currently since the driver only supports DT but it will be
needed if the driver is changed to be built as a module since the I2C
core always reports a I2C modalias uevent so auto-load will not work.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-03-16 08:50:40 +00:00
Javier Martinez Canillas 7f8ada1a84 mfd: max77686: Export OF module alias information
When the device is registered via OF, the OF table is used to match the
driver instead of the I2C device ID table but the entries in the latter
are used as aliasses to load the module if the driver was not built-in.

This is because the I2C core always reports an I2C module alias instead
of an OF one but that could change so it is better to always export it.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-03-16 08:50:39 +00:00
Laxman Dewangan f3937549a9 rtc: max77686: move initialisation of rtc regmap, irq chip locally
To make RTC block of MAX77686/MAX77802 as independent driver,
move the registration of i2c device, regmap for register access
and irq_chip for interrupt support inside the RTC driver.
Removed the same initialisation from MFD driver.

Having this change will allow to reuse this driver for different
PMIC/devices from Maxim Semiconductor if they kept same RTC IP on
different PMIC. Some of examples as PMIC MAX77620, MAX20024 where
same RTC IP used and hence driver for these chips will use this
driver only for RTC support.

Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-03-14 17:08:13 +01:00
Laxman Dewangan 08e37ef17d mfd: max77686: do not set i2c client data for rtc i2c client
There is different RTC I2C address for RTC block in MAX77686.
Driver is creating dummy i2c client for this address to access
the register of this IP block.

As there is no call to i2c_get_clientdata() for rtc_i2c client,
there is no need to store pointer and hence removing the call
to set client data for rtc i2c client.

Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-03-14 17:08:12 +01:00
Geliang Tang 1b5420e1f5 mfd: Use to_i2c_client() instead of open-coding it
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-01-14 08:43:50 +00:00
Krzysztof Kozlowski 0e777366fb mfd: Drop owner assignment from i2c_drivers
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-08-11 15:08:48 +01:00
Krzysztof Kozlowski 2b50635ea3 mfd: max77686/802: Remove support for board files
The driver is used only on Exynos based boards with DTS support.
After removal of board file support from max77686 and max77802 regulator
drivers, the MFD driver can be converted to DTS-only version. This
simplifies a little the code:
1. No dead (unused) entries in platform_data structure.
2. More code removed.
3. Regulator driver does not depend on allocated memory
   from MFD driver.
4. It makes also easier extending the regulator driver.

Add to the max77686 MFD driver dependency on CONFIG_OF because without
DTS the regulator drivers (max77686 and max77802) won't bind.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-01-22 16:03:55 +00:00
Krzysztof Kozlowski 68be231ccf mfd: max77686: Constify struct regmap_config
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-01-22 15:56:14 +00:00
Lee Jones b87d9a0fed mfd: max77686: Remove check which is always true
As 'reg' is unsigned, it can't be less than 0, so checking if it is
greater than or equal to 0 will always result in a true condition.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:32 +01:00
Lee Jones ec8bd56699 mfd: max77686: Ensure device type IDs are architecture agnostic
Extinguishes:

../drivers/mfd/max77686.c: In function ‘max77686_i2c_probe’:
../drivers/mfd/max77686.c:254:20:
	warning: cast from pointer to integer of different size

Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-25 15:31:48 +01:00
Javier Martinez Canillas a259f3896a mfd: max77686: Add Maxim 77802 PMIC support
Maxim MAX77802 is a power management chip that contains 10 high
efficiency Buck regulators, 32 Low-dropout (LDO) regulators used
to power up application processors and peripherals, a 2-channel
32kHz clock outputs, a Real-Time-Clock (RTC) and a I2C interface
to program the individual regulators, clocks outputs and the RTC.

This patch adds support for MAX77802 to the MAX77686 driver and is
based on a driver added to the Chrome OS kernel 3.8 by Simon Glass.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-25 15:31:48 +01:00
Lee Jones a31b0fa6cc mfd: max77686: Fix 'line over 80 chars' warning
This is part of an effort to clean-up the MFD subsystem.

+WARNING: line over 80 characters
+                                      &max77686_rtc_regmap_config);

total: 0 errors, 1 warnings, 299 lines checked

Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-21 16:58:26 +01:00
Javier Martinez Canillas 8a789b647d mfd: max77686: Remove unneeded OOM error message
There is no need to print out-of-memory errors since this is already
done by the memory management subsystem which even calls dump_stack().

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-21 16:54:31 +01:00
Javier Martinez Canillas c0e0fcdaa9 mfd: max77686: Make error checking consistent
Error checking across the driver is mostly consistent besides
a few exceptions, so change these exceptions for consistency.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-21 16:54:30 +01:00
Javier Martinez Canillas b452d7b69d mfd: max77686: Return correct error when pdata isn't found
When platform data is not found an -EIO (I/O error) code is returned.
This doesn't seem to be the correct error so better return -EINVAL
(Invalid argument) which is what most drivers do in this case.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-21 16:54:29 +01:00
Javier Martinez Canillas ede04c6164 mfd: max77686: Make platform data over-rule DT
The function max77802_i2c_parse_dt_pdata() should only be called
if there isn't already platform data for the device.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-21 16:54:28 +01:00
Javier Martinez Canillas 154409e450 mfd: max77686: Don't define dummy function if OF isn't enabled
When the CONFIG_OF option was not enabled, a dummy function
max77686_i2c_parse_dt_pdata() was defined since this is called
unconditionally on probe(). Just always define the real function
and conditionally call it if CONFIG_OF is enabled instead.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-21 16:54:28 +01:00
Javier Martinez Canillas 2b52b5d5f2 mfd: max77686: Add power management support
The driver doesn't have PM operations defined so add a suspend
and resume function handlers to allow the PMIC IRQ to wakeup
the system when it is put into a sleep state.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-21 16:54:27 +01:00
Javier Martinez Canillas 6f1c1e71d9 mfd: max77686: Convert to use regmap_irq
By using the generic IRQ support in the Register map API, it
is possible to get rid max77686-irq.c and simplify the code.

Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-21 16:54:26 +01:00
Krzysztof Kozlowski b68ece3d8e mfd: max77686: Make of_device_id array const
Array of struct of_device_id may be be const as expected by
of_match_table field.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-06-03 08:11:30 +01:00
Krzysztof Kozlowski b9e183a1d4 mfd: max77686: Fix possible NULL pointer dereference on i2c_new_dummy error
During probe the driver allocates dummy I2C device for RTC with
i2c_new_dummy() but it does not check the return value of this call.

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().

If i2c_new_dummy() fails for RTC device, fail also the probe for main
MFD driver.

Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-03-19 08:58:09 +00:00
Krzysztof Kozlowski 74142ffc0b mfd: max77686: Fix regmap resource leak on driver remove
The regmap used by max77686 MFD driver was not freed with regmap_exit()
on driver exit. This lead to leak of resources.

Replace regmap_init_i2c() call in driver probe with initialization of
managed register map so the regmap will be properly freed by the device
management code.

Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-01-21 08:28:13 +00:00
Geert Uytterhoeven 7c0517b171 mfd: maxim: Constify struct mfd_cell where possible
As of commit 03e361b25e ("mfd: Stop setting
refcounting pointers in original mfd_cell arrays"), the "cell" parameter of
mfd_add_devices() is "const" again. Hence make all cell data passed to
mfd_add_devices() const where possible.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-01-06 09:13:27 +00:00
Sachin Kamat 2a048d3b78 mfd: max77686: Include linux/of.h header
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid breakage in the future.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-10-23 16:22:23 +01:00
Jingoo Han 334a41ce9b mfd: Use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-07-31 13:01:29 +01:00
Lee Jones 742413a48f mfd: max77686: Convert to managed resources for allocating memory
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-06-13 12:11:45 +02:00
Olof Johansson c0fa7e104b mfd: max77687: Add registration of max77686-clk
The MAX77686 clock driver has been in-tree for over 6 months, but never
actually enabled through the MFD registration before.

Add it to the table so the device will probe and configure properly.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-06-11 19:36:59 +02:00
Sachin Kamat d1ac2c092d mfd: max77686: Use NULL instead of 0
'data' is a pointer and hence use NULL instead of 0.
Silences the following warning:
drivers/mfd/max77686.c:49:50: warning: Using plain integer as NULL pointer

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-04-08 11:47:15 +02:00
Axel Lin 136d982eca mfd: max77686: Init max77686->dev before using it
Current code uses max77686->dev in the dev_err call before setting it to
&i2c->dev. Fix it.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-01-22 03:02:21 +01:00
Bill Pemberton a9e9ce4c41 mfd: remove use of __devinitdata
CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-28 12:21:11 -08:00
Mark Brown 0848c94fb4 mfd: core: Push irqdomain mapping out into devices
Currently the MFD core supports remapping MFD cell interrupts using an
irqdomain but only if the MFD is being instantiated using device tree
and only if the device tree bindings use the pattern of registering IPs
in the device tree with compatible properties.  This will be actively
harmful for drivers which support non-DT platforms and use this pattern
for their DT bindings as it will mean that the core will silently change
remapping behaviour and it is also limiting for drivers which don't do
DT with this particular pattern.  There is also a potential fragility if
there are interrupts not associated with MFD cells and all the cells are
omitted from the device tree for some reason.

Instead change the code to take an IRQ domain as an optional argument,
allowing drivers to take the decision about the parent domain for their
interrupts.  The one current user of this feature is ab8500-core, it has
the domain lookup pushed out into the driver.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-09-15 23:22:04 +02:00
Axel Lin 2984fc0093 mfd: Guard max77686_pmic_dt_match with CONFIG_OF
This fixes below build warning if CONFIG_OF is not set.

  CC      drivers/mfd/max77686.o
drivers/mfd/max77686.c:37:42: warning: 'max77686_pmic_dt_match' defined but not used [-Wunused-variable]

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-07-10 11:00:37 +02:00
Yadwinder Singh Brar c1516f840d mfd: Add device tree support for max77686
This patch adds device tree support for mfd driver and adds
Documentation/devicetree/bindings/mfd/max77686.txt.
This patch also intialize max77686 pointer to NULL in max77686_i2c_probe
to silent a compile time warning.

Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-07-09 15:13:42 +02:00
Yadwinder Singh Brar 2b40459b7e mfd: Allow to specify max77686 interrupt through DT or platform file also
Presently driver expects irq_gpio pin in platform data and maps it to irq
itself. But we can also directly specify the interrupt in DT or platform file.

Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-07-09 15:13:42 +02:00
Axel Lin b874809611 mfd: Remove unused max77686 iolock mutex
Now this driver is using regmap API, the iolock mutex is not used and
can be removed.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-07-09 00:16:14 +02:00
Jonghwa Lee dae8a969d5 mfd: Add Maxim 77686 driver
This patch is device driver for MAX77686 chip.
MAX77686 is PMIC and includes regulator and rtc on it.
This driver is core of MAX77686 chip, so provides common support for
accessing on-chip devices. It uses irq_domain to manage irq and regmap
to read/write data to its register with i2c bus.

Signed-off-by: Chiwoong Byun <woong.byun@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-07-09 00:16:07 +02:00