Clean up the following includecheck warning:
./drivers/watchdog/dw_wdt.c: linux/kernel.h is included more than once.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1620904182-74107-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200713205821.38223-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
For the sake of the easier device-driver debug procedure, we added a
DebugFS file with the controller registers state. It's available only if
kernel is configured with DebugFS support.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200530073557.22661-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
DW Watchdog can rise an interrupt in case if IRQ request mode is enabled
and timer reaches the zero value. In this case the IRQ lane is left
pending until either the next watchdog kick event (watchdog restart) or
until the WDT_EOI register is read or the device/system reset. This
interface can be used to implement the pre-timeout functionality
optionally provided by the Linux kernel watchdog devices.
IRQ mode provides a two stages timeout interface. It means the IRQ is
raised when the counter reaches zero, while the system reset occurs only
after subsequent timeout if the timer restart is not performed. Due to
this peculiarity the pre-timeout value is actually set to the achieved
hardware timeout, while the real watchdog timeout is considered to be
twice as much of it. This applies a significant limitation on the
pre-timeout values, so current implementation supports either zero value,
which disables the pre-timeout events, or non-zero values, which imply
the pre-timeout to be at least half of the current watchdog timeout.
Note that we ask the interrupt controller to detect the rising-edge
pre-timeout interrupts to prevent the high-level-IRQs flood, since
if the pre-timeout happens, the IRQ lane will be left pending until
it's cleared by the timer restart.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200530073557.22661-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
DW Watchdog IP core can be synthesised with asynchronous timer/APB
clocks support (WDT_ASYNC_CLK_MODE_ENABLE == 1). In this case
separate clock signals are supposed to be used to feed watchdog timer
and APB interface of the device. Currently the driver supports
the synchronous mode only. Since there is no way to determine which
mode was actually activated for device from its registers, we have to
rely on the platform device configuration data. If optional "pclk"
clock source is supplied, we consider the device working in asynchronous
mode, otherwise the driver falls back to the synchronous configuration.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200530073557.22661-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
In case if the DW Watchdog IP core is synthesised with
WDT_USE_FIX_TOP == false, the TOP interval indexes make the device
to load a custom periods to the counter. These periods are hardwired
at the IP synthesis stage and can be within [2^8, 2^(WDT_CNT_WIDTH - 1)].
Alas their values can't be detected at runtime and must be somehow
supplied to the driver so one could properly determine the watchdog
timeout intervals. For this purpose we suggest to have a vendor-
specific dts property "snps,watchdog-tops" utilized, which would
provide an array of sixteen counter values. At device probe stage they
will be used to initialize the watchdog device timeouts determined
from the array values and current clocks source rate.
In order to have custom TOP values supported the driver must be
altered in the following way. First of all the fixed-top values
ready-to-use array must be determined for compatibility with currently
supported devices, which were synthesised with WDT_USE_FIX_TOP == true.
It will be used if either fixed TOP feature is detected being enabled or
no custom TOPs are fetched from the device dt node. Secondly at the probe
stage we must initialize an array of the watchdog timeouts corresponding
to the detected TOPs list and the reference clock rate. For generality the
procedure of initialization is designed in a way to support the TOPs array
with no limitations on the items order or value. Finally the watchdog
period search methods should be altered to support the new timeouts data
structure.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200530073557.22661-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Currently on an rk3288 SoC when trying to use the watchdog the SoC will
instantly reset. This is due to the watchdog countdown counter being set
to its initial value of 0x0. Reset the watchdog counter before start in
order to correctly start the countdown timer from the right position.
Signed-off-by: Jack Mitchell <ml@embed.me.uk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200107155155.278521-1-ml@embed.me.uk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
watchdog_dev.c provides means to allow users to set bigger timeout value
than HW can support, make DesignWare watchdog align with this.
Signed-off-by: Peng Wang <peng.1.wang@nokia-sbell.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/8fa54e92c6cd4544a7a3eb60a373ac43@nokia-sbell.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When switch to watchdog infrastructure, pr_* usage is removed, so
there's no any users of the pr_fmt, remove it.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Some platforms lose this state in suspend. It should be safe to do this
unconditionally.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
RK3399 has rst_pulse_length in CONTROL_REG[4:2], determining the length
of pulse to issue for system reset. We shouldn't clobber this value,
because that might make the system reset ineffective. On RK3399, we're
seeing that a value of 000b (meaning 2 cycles) yields an unreliable
(partial?) reset, and so we only fully reset after the watchdog fires a
second time. If we retain the system default (010b, or 8 clock cycles),
then the watchdog reset is much more reliable.
Read-modify-write retains the system value and improves reset
reliability.
It seems we were intentionally clobbering the response mode previously,
to ensure we performed a system reset (we don't support an interrupt
notification), so retain that explicitly.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The only way of stopping the watchdog is by resetting it.
Add the watchdog op for stopping the device and reset if
a reset line is provided.
At same time WDOG_HW_RUNNING should be remove from dw_wdt_start.
As commented by Guenter Roeck:
dw_wdt sets WDOG_HW_RUNNING in its open function. Result is
that the kref_get() in watchdog_open() won't be executed. But then
kref_put() in close will be called since the watchdog now does stop.
This causes the imbalance.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The dw_wdt has an external reset line, that can keep the device in reset
and therefore rendering it useless and also is the only way of stopping
the watchdog once it was started.
Get the reset lines for this core from the devicetree. As these lines are
optional, use devm_reset_control_get_optional_shared. If the reset line
is not specified in the devicetree, the reset framework will just skip
deasserting and continue.
This way all users of the driver will continue to function without
any harm, even if the reset line is not specified in the devicetree.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Coverity reports:
divide_by_zero: In expression readl(dw_wdt->regs + 8) /
clk_get_rate(dw_wdt->clk), division by expression clk_get_rate(dw_wdt->clk)
which may be zero has undefined behavior.
The clock used for the watchdog timer won't change its rate, so read it
only once during probe. Also validate it and abort the probe function
with an error if it is 0.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Convert driver to use watchdog infrastructure. This includes
infrastructure support to handle watchdog keepalive if the watchdog
is running while the watchdog device is closed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On 64bit platforms, "(1 << (16 + top)) / clk_get_rate(dw_wdt.clk)" is
sign-extended to 64bit then converted to unsigned 64bit, finally divide
the clk rate. If the top is the maximum TOP i.e 15, "(1 << (16 +15))"
will be sign-extended to 0xffffffff80000000, then converted to unsigned
0xffffffff80000000, which is a huge number, thus the final result is
wrong.
We fix this issue by giving usigned value(1U in this case) at first.
Let's assume clk rate is 25MHZ,
Before the patch:
dw_wdt_top_in_seconds(15) = -864612050
After the patch:
dw_wdt_top_in_seconds(15) = 85
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If you've got code that does this in a tight loop
1. Open watchdog
2. Send 'expect close'
3. Close watchdog
...you'll eventually trigger a watchdog reset. You can reproduce this
by using daisydog (1) and running:
while true; do daisydog -c > /dev/null; done
The problem is that each time you write to the watchdog for 'expect
close' it moves the timer .5 seconds out. The timer thus never fires
and never pats the watchdog for you.
1: http://git.chromium.org/gitweb/?p=chromiumos/third_party/daisydog.git
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Right now the dw_wdt uses a spinlock to protect dw_wdt_open(). The
problem is that while holding the spinlock we call:
-> dw_wdt_set_top()
-> dw_wdt_top_in_seconds()
-> clk_get_rate()
-> clk_prepare_lock()
-> mutex_lock()
Locking a mutex while holding a spinlock is not allowed and leads to
warnings like "BUG: spinlock wrong CPU on CPU#1", among other
problems.
There's no reason to use a spinlock. Only dw_wdt_open() was protected
and the test_and_set_bit() at the start of that function protects us
anyway.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The dw_wdt_set_top() function takes in a value in seconds. In
dw_wdt_open() we were calling it with a value that's supposed to
represent the maximum value programmed into the "top" register with a
comment saying that we were trying to set the watchdog to its maximum
value. Instead we ended up setting the watchdog to ~15 seconds.
Let's fix this. However, setting things to the "max" gives me an 86
second watchdog in the system I'm looking at. 86 seconds feels a
little too long. We'll explicitly choose 30 seconds as a more
reasonable value.
NOTE: Ideally this driver should be transitioned to be a real watchdog
driver. Then we could use "watchdog_init_timeout" and let the timeout
be specified in a number of ways (device tree, module parameter, etc).
This patch should be considered a bit of a stopgap solution.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On some dw_wdt implementations the "top" register may be initted to 0
at bootup. In such a case, each "pat" of the watchdog will reset the
timer to 0xffff. That's pretty short.
The input clock of the wdt can be any of a wide range of values. On
an rk3288 system, I've seen the wdt clock be 24.75 MHz. That means
each tick is ~40ns and we'll count to 0xffff in ~2.6ms.
Because of the above two facts, it's a really good idea to pat the
watchdog after initting the "top" register properly and before
enabling the watchdog. If you don't then there's no way we'll get the
next heartbeat in time.
Jisheng Zhang fixed this problem on some dw_wdt versions by using the
TOP_INIT feature. However, the dw_wdt on rk3288 doesn't have TOP_INIT
so it's a good idea to also pat the watchdog manually.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The kernel core now provides an API to trigger a system restart.
Register with it to support restarting the system via. watchdog.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The TOP_INIT, ie bit 4-7 of the WDOG_TIMEOUT_RANGE_REG_OFFSET register
may be zero, so the timeout period may be very short after initialization
is done, thus the system may be reset soon after enabling. We fix this
problem by also initialising the TOP_INIT when setting TOP in function
dw_wdt_set_top().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
devm_ioremap_resource() checks for valid resource.
Remove the un-necessary check after platform_get_resource().
Signed-off-by: George Cherian <george.cherian@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is nothing ARM specific in this driver, and we intend to use it on the
Xtensa architecture. Also, clk.h now includes stubs for !CONFIG_HAVE_CLK, so
the driver should build anyway.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
I just can't find any value in MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR)
and MODULE_ALIAS_MISCDEV(TEMP_MINOR) statements.
Either the device is enumerated and the driver already has a module
alias (e.g. PCI, USB etc.) that will get the right driver loaded
automatically.
Or the device is not enumerated and loading its driver will lead to
more or less intrusive hardware poking. Such hardware poking should be
limited to a bare minimum, so the user should really decide which
drivers should be tried and in what order. Trying them all in
arbitrary order can't do any good.
On top of that, loading that many drivers at once bloats the kernel
log. Also many drivers will stay loaded afterward, bloating the output
of "lsmod" and wasting memory. Some modules (cs5535_mfgpt which gets
loaded as a dependency) can't even be unloaded!
If defining char-major-10-130 is needed then it should happen in
user-space.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Cc: Jim Cromie <jim.cromie@gmail.com>
This is necessary to make the driver work with platforms using the
common clock framework.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The dw_wdt only provides PM_SLEEP operations, so convert the driver
to use SIMPLE_DEV_PM_OPS instead of populating the struct manually.
This has the added effect of simplifying the CONFIG_PM ifdefs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
'dw_wdt_write' is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use devm_clk_get() to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the current logging styles.
Make sure all output has a prefix.
Add missing newlines.
Remove now unnecessary PFX, NAME, and miscellaneous other #defines.
Coalesce formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Reimplement a call to devm_request_mem_region followed by a call to ioremap
or ioremap_nocache by a call to devm_request_and_ioremap.
The semantic patch that makes this transformation is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@nm@
expression myname;
identifier i;
@@
struct platform_driver i = { .driver = { .name = myname } };
@@
expression dev,res,size;
expression nm.myname;
@@
-if (!devm_request_mem_region(dev, res->start, size,
- \(res->name\|dev_name(dev)\|myname\))) {
- ...
- return ...;
-}
... when != res->start
(
-devm_ioremap(dev,res->start,size)
+devm_request_and_ioremap(dev,res)
|
-devm_ioremap_nocache(dev,res->start,size)
+devm_request_and_ioremap(dev,res)
)
... when any
when != res->start
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch converts the drivers in drivers/watchdog/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Nicolas Thill <nico@openwrt.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Marc Zyngier <maz@misterjones.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alejandro Cabrera <aldaya@gmail.com>
Cc: "George G. Davis" <gdavis@mvista.com>
Cc: Sylver Bruneau <sylver.bruneau@googlemail.com>
Cc: Vitaly Wool <vital@embeddedalley.com>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Cc: Timo Kokkonen <timo.t.kokkonen@nokia.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Synopsys DesignWare watchdog is found in several ARM based systems
and provides a choice of 16 timeout periods depending on the clock
input. The watchdog cannot be disabled once started.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Jiapeng Chong
Alexander A. Klimov
Serge Semin
Jack Mitchell
Wang, Peng 1. (NSB - CN/Hangzhou)
Thomas Gleixner
Guenter Roeck
Jisheng Zhang
Brian Norris
Oleksij Rempel
Steffen Trumtrar
Jisheng Zhang
Doug Anderson
Greg Kroah-Hartman
Wolfram Sang
George Cherian
Baruch Siach
Dinh Nguyen
Jean Delvare
Jingoo Han
Heiko Stübner
Sachin Kamat
Thierry Reding
Bill Pemberton
Wim Van Sebroeck
Joe Perches
Julia Lawall
Axel Lin
Jamie Iles