Move capture PCM pin from PCM4 to PCM0 for Broadwell/Haswell.
This will allow us to integrate with pulseaudio better for
usually default device is set to 0.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The xmax volume should be corrected to ARRAY_SIZE(volume_map)-1, otherwise,
the xmax value will be mapped to 0 wrongly.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
User can pass snoop option to enable/disable the snoop behavior, but
currently azx_check_snoop_available() always turns it off for some
devices. For better debuggability, change the parameter as bint, and
allow user to enable/disable forcibly the snoop when specified via the
module option.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new driver_caps bit, AZX_DCAPS_SNOOP_OFF, to set the snoop off
as default. This new bit is used for the checks in
azx_check_snoop_available(). Most of case-switches are replaced with
the new dcaps in each entry.
While working on it, for avoiding to spend more bits, combine three
bits AZX_DCAPS_SNOOP_SCH, AZX_DCAPS_SNOOP_ATI and
AZX_DCAPS_SNOOP_NVIDIA bits into a flat type of two bits. This
reduces the bits usages, and assign AZX_DCAPS_OFF to this empty bit
now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to the sgtl5000 datasheet the MCLK frequency range restriction of
8 to 27 MHz only applies when the PLL is used - synchronous SYS_MCLK input mode.
mxs-sgtl5000 machine sets the codec as slave, and mx28 generates MCLK in the
range of 256*fs, 384*fs or 512*fs, which is called asynchronous SYS_MCLK
input.
In asynchronous SYS_MCLK we cannot have the 8 to 27 MHz check because if we
want to play a 8KHz sample rate track, with a MCLK of 8k * 512 = 4.096MHz the
current check would return -EINVAL, which is not correct.
Remove the 8 to 27MHz frequency check, since this only applies to the
synchronous SYS_MCLK input case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When trying to play a 8kHz file with codec in slave mode we get the following
error on a mx28evk:
$ aplay -Dhw:0,0 stereo_8k.wav
Playing WAVE 'stereo_8k.wav' : Signed 16 bit Little Endian, Rate 8000 Hz, Stereo
[ 21.218647] sgtl5000 0-000a: PLL not supported in slave mode
[ 21.224559] sgtl5000 0-000a: 128 ratio is not supported. SYS_MCLK needs to be 256, 384 or 512 * fs
[ 21.233687] sgtl5000 0-000a: ASoC: can't set sgtl5000 hw params: -22
aplay: set_params:1123: Unable to install hw params:
This error happens because we are using 'sys_fs' instead of 'frame_rate' in the
valid ratio check.
Use the real'frame_rate' so that the ratio is correctly calculated and the
playback can run.
sgtl5000 codec manual states that in 'Synchronous SYS_MCLK input' mode that the
following SYS_CLK frequencies are allowed: 256*fs, 384*fs, 512*fs.
, where fs is the sampling frequency, which can be in the range of:
8, 11.025, 16, 22.5, 32, 44.1, 48, 96 kHz.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the sgtl5000 datasheet the MCLK frequency range restriction of
8 to 27 MHz only applies when the PLL is used - synchronous SYS_MCLK input mode.
When running the codec as slave, the master should generate MCLK in the range of
256*fs, 384*fs or 512*fs, which is called asynchronous SYS_MCLK input mode.
In asynchronous SYS_MCLK we cannot have the 8 to 27 MHz check because if we
want to play a 8KHz sample rate track, with a MCLK of 8k * 512 = 4.096MHz the
current check would return -EINVAL, which is not correct.
Remove the 8 to 27MHz frequency check, since this only applies to the
synchronous SYS_MCLK input case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the manual transition back to SND_SOC_BIAS_STANDBY in resume. This
is already be automatically handled by the ASoC core.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed. While we are at it also remove the unused codec field from
the cq93vc struct so the whole probe function can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
While two of the fields in the cq93vc driver state struct are initialized
none of them are ever acutally read again. So remove the whole struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Broadwell, the ADSP FW don't support loopback record volume tuning,
so here remove this control.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "changed" variable should be set to false at the start.
Fixes: a35daac77a ('ASoC: sigmadsp: Add support for fw v2')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
We must ensure that the clocking configuration is valid as rapidly as possible.
And do software reset before the others registers updates, or the registers
will be reset to the default state.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In olden times the snd_hda_param_read() function always set "*start_id"
but in 2007 we introduced a new return and it causes uninitialized data
bugs in a couple of the callers: print_codec_info() and
hdmi_parse_codec().
Fixes: e8a7f136f5 ('[ALSA] hda-intel - Improve HD-audio codec probing robustness')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adding machine driver to instantiate I2S based realtek's ALC5631
sound card on Arndale board.
There are other variants of Audio Daughter Cards for Arndale
Board for which support already exists but there is no support for
Realtek's alc5631 codec hence support for ALC5631 based machine
driver is being added.
This patch also documents the device tree binding for the Arndale
board based machine driver.
Signed-off-by: Claude Youn <claude.youn@gmail.com>
Signed-off-by: Krishna Mohan Dani <krishna.md@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If regmap is disabled there will be no users of the ASoC regmap helpers.
Furthermore regmap_exit() will no be defined causing the following compile
error:
sound/soc/soc-core.c: In function 'snd_soc_component_exit_regmap':
sound/soc/soc-core.c:2645:2: error: implicit declaration of function
'regmap_exit' [-Werror=implicit-function-declaration]
So disable the helpers if regmap is disabled.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 20feb88198 ASoC: Add helper functions for deferred regmap setup")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pass flags to gpiod_get() to automatically configure the GPIOs. This is shorter
and not passing any flags to gpiod_get() will eventually no longer be supported.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The device node pointer 'cpu' is not used in the function
asoc_simple_card_parse_daifmt().
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch exports a core function which handles the DT description
of multi-codec links (as: "sound-dai = <&hdmi 0>, <&spdif_codec>;")
and creates a CODEC component array in the DAI link.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
The volume setting control for capture stream doesn't take effect on intel
Broadwell platform. Root cause it at 2 points:
1. set stream volume with channel=2 is wrongly bapassed;
2. the saved stream volume should be restored after stream is commit.
Here correct these 2 items to fix the stream volume set issue.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ESAI may need to use fixed slot width to comply with external
CODEC. So this set_tdm_slot() call will allow the ESAI driver
to override its default dynamic slot width policy.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver previously used 32-bit fixed slot width as default.
In result, ESAI might use 32-bit length to capture 16-bit width
audio slot from CODEC side when ESAI is running as DAI slave.
So this patch just removes the default slot_width so as to use
dynamic slot width. If there comes a specific situation that
needs a fixed width, the machine driver shall set slot_width
via set_tdm_slot() so as to let the ESAI driver replace the
dynamic width policy with the fixed value.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the patch "ASoC: rt5677: Use specific r/w function for DSP mode", the
regmap_range "rt5677_ranges" was not registered in rt5677_regmap_physical, and
it caused that the regmap_range "rt5677_ranges" cannot be accessed by the
specific r/w function. The patch fixes this issue.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch will enable ASRC for DMIC if ASRC is useable.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To use ASRC, the sysclk should be faster than 384 times sample rate of I2S1.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are 3 JD modes in RT5645. This patch configure register
values according to platform data.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/sigmadsp.c:656:1-4: WARNING: end returns can be simpified and declaration on line 636 can be dropped
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, CONFIG_SND_SOC_ROCKCHIP_I2S could also be selected
without having CONFIG_SND_SOC_ROCKCHIP enabled.
As this makes no sense, a Kconfig dependency is added to
CONFIG_SND_SOC_ROCKCHIP_I2S. This will make the item visible only if
CONFIG_SND_SOC_ROCKCHIP is enabled.
Additionally, as the code connected to CONFIG_SND_SOC_ROCKCHIP_I2S
depends on CONFIG_SND_SOC_GENERIC_DMAENGINE_PCM, the dependency
is moved to reflect this more clearly.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix off by one read beyond the end of a table.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend. This makes the code a bit shorter and cleaner.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner. Also remove the regcache_mark_dirty()
from the suspend handler since it is already called by the ASoC core.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner. Also remove the regcache_mark_dirty()
from the suspend handler since this is already done by the ASoC core.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed. Also remove the unused codec field from the wm8903_priv
struct so we can remove the whole probe callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner. Also remove the extra write that sets
the WM8711_ACTIVE register to 0x00 in the suspend handler since this write
is already done when transitioning to SND_SOC_BIAS_OFF.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual asynchronous transition to SND_SOC_BIAS_STANDBY at the end of
CODEC probe() can also be removed as the core will automatically do this
after the CODEC has been probed. Also running this asynchronously has the
problem of potential race conditions with the core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner. Also remove the manual sequencing back
to SND_SOC_BIAS_ON in resume as this is already handled by the ASoC core.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to its documentation the is_powered_on_standby field of the
uda134x platform data is supposed to prevent the the driver from shutting
down the ADC and DAC in standby mode. This behavior was broken in commit
commit f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support")
almost 5 years ago and all the flag does now is cause the driver to go to
SND_SOC_BIAS_ON in probe, just for the ASoC core to put it back into
SND_SOC_BIAS_STANDBY right after probe.
Apparently the intended behavior has not been missed, so just remove
is_powered_on_standby from the platform data struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is right not left sidetone which goes to "DACR".
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 5fe5b767dc ("ASoC: dapm: Do not pretend to support controls for non
mixer/mux widgets") revealed ill-defined control in a route between
"STENL Mux" and DACs in max98090.c:
max98090 i2c-193C9890:00: Control not supported for path STENL Mux -> [NULL] -> DACL
max98090 i2c-193C9890:00: ASoC: no dapm match for STENL Mux --> NULL --> DACL
max98090 i2c-193C9890:00: ASoC: Failed to add route STENL Mux -> NULL -> DACL
max98090 i2c-193C9890:00: Control not supported for path STENL Mux -> [NULL] -> DACR
max98090 i2c-193C9890:00: ASoC: no dapm match for STENL Mux --> NULL --> DACR
max98090 i2c-193C9890:00: ASoC: Failed to add route STENL Mux -> NULL -> DACR
Since there is no control between "STENL Mux" and DACs the control name must
be NULL not "NULL".
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Commit e409dfbfcc ("ASoC: dapm: Add a few supply widget sanity checks")
broke digital microphone support in max98090.c:
max98090 i2c-193C9890:00: Conditional paths are not supported for supply widgets (DMICL_ENA -> [DMIC] -> DMIC Mux)
max98090 i2c-193C9890:00: ASoC: no dapm match for DMICL_ENA --> DMIC --> DMIC Mux
max98090 i2c-193C9890:00: ASoC: Failed to add route DMICL_ENA -> DMIC -> DMIC Mux
max98090 i2c-193C9890:00: Conditional paths are not supported for supply widgets (DMICR_ENA -> [DMIC] -> DMIC Mux)
max98090 i2c-193C9890:00: ASoC: no dapm match for DMICR_ENA --> DMIC --> DMIC Mux
max98090 i2c-193C9890:00: ASoC: Failed to add route DMICR_ENA -> DMIC -> DMIC Mux
Problem is partially caused by commit f69e3caa9e ("ASoC: max98090: Enable
both DMIC channels also when using mono configuration") which connects
"DMICL_ENA" and "DMICR_ENA" supply widgets to "DMIC Mux".
Fix the breakage by reverting f69e3caa9e and then by adding additional
"DMICR_ENA" to "DMICL" and "DMICL_ENA" to "DMICR" cross-connections. This
disconnects these supply widgets from the mux and makes sure that both DMIC
data channels are still enabled together.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A number of radeon cards have a HW limitation causing them to be
unable to generate the full 64-bit of address bits for MSIs. This
breaks MSIs on some platforms such as POWER machines.
We used to have a powerpc specific quirk to address that on a
single card, but this doesn't scale very well, this is better
put under control of the drivers who know precisely what a given
HW revision can do.
We now have a generic quirk in the PCI code. We should set it
appropriately for all radeon's from the audio driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
CC: <stable@vger.kernel.org>
AMD/ATI HDMI controller chip models, we already have a filter to lower
to 32bit DMA, but the rest are supposed to be working with 64bit
although the hardware doesn't really work with 63bit but only with 40
or 48bit DMA. In this patch, we take 40bit DMA for safety for the
AMD/ATI controllers as the graphics drivers does.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Only determining if low latency mode is enabled. Failure
indicates adapter has no modes
Signed-off-by: Eliot Blennerhassett <eliot@blennerhassett.gen.nz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some cards have a so-called low-latency mode, in which they present
a single multichannel stream with no mixing or samplerate conversion.
In this mode the card can generate an interrupt per internal processing
block (typically 32 or 64 frames)
Signed-off-by: Eliot Blennerhassett <eliot@blennerhassett.gen.nz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Audio cards wth have AVB or BLU Link IO.
Tuner card with DAB receiver
Signed-off-by: Eliot Blennerhassett <eliot@blennerhassett.gen.nz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"devc" can't be NULL here so there is no need to check. Also I removed
the "devc = NULL" assignment because devc is stored on stack so it's
a no-op.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/soc/intel/sst/sst_acpi.c:135:26: sparse: symbol 'chv_platform_data' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Skip dpcm path checking for playback or capture, if corresponding FE
doesn't support playback or capture, or currently is not ready. It
can reduce the unnecessary cost to search connected widgets.
[Tweaked comments for clarity -- broonie]
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch add ACPI device ID and platform data for two Cherryview-based
platforms, Cherrytrail and Braswell. Also reuse mfld driver ops in sst driver.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add machine driver for two Intel Cherryview-based platforms, Cherrytrail and
Braswell, with RT5672 codec.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The functions release_and_free_resource() and snd_util_memhdr_free() test
whether their argument is NULL and then return immediately.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The release_and_free_resource() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The functions snd_seq_oss_timer_delete() and vunmap() perform also input
parameter validation. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the device tree binding for the WM8960 codec, and modify the
driver to extract the platform data from device tree, if present.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to always convert the firmware data to local endianness before
using it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: a35daac77a ("ASoC: sigmadsp: Add support for fw v2")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
To be able to read back data from the DSP parameter memory the register
range needs to be marked as readable. At the same time we do not want them
to e.g. appear in debugfs output so mark them as precious as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
While we are at it also replace dev_get_drvdata() with snd_soc_codec_get_drvdata().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the i2s_set_sysclk() callback we are currently clearing all bits
of the IISMOD register in i2s_set_sysclk. It's due to an incorrect
mask used for the AND operation which is introduced in commit
a5a56871f8 (ASoC: samsung:
add support for exynos7 I2S controller) and also adds the missing
break statement.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/intel/sst/sst_acpi.c:124:26: sparse: symbol 'byt_rvp_platform_data' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes XMOS DSD sample format to DSD_U32_BE and also adds
DSD_U16_BE and DSD_U32_BE sample formats.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Acked-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Scarlett driver uses almost compatible usb_mixer_elem_info struct, so
we just need to add a couple of simple resume callbacks to handle them
accordingly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the previous fixes, the mixer accessors are converted to use
usb_mixer_elem_list objects. In addition, the proper shutdown check
are put in get and put callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few FTU mixer controls have the own value handling, so they have to
be rewritten to follow the support for resume callbacks. This ended
up in a fair amount of refactoring. Its own struct is now removed,
instead the values are embedded in kctl private_value totally.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The changes at this time are a bit more wider than previous ones.
Firstly, the NI controls didn't cache the values, so I had to
implement the caching. It's stored in bit 24 of private_value.
In addition to that, the initial values have to be read from
registers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This time it's about Xonar U1: add the proper resume support for
"Digital Playback Switch" element.
Also, the status is moved into kcontrol private_value from
usb_mixer_interface struct field. One more cut.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar as the previous fix, this adds the proper resume support to
Emu0202 "Front Jack Channels" enum mixer element.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rewrite the code to handle LEDs on audigy2nx and co for supporting the
proper resume. A new internal helper function
add_single_ctl_with_resume() is introduced to manage the
usb_mixer_elem_list more easily.
Also while we're at it, move audigy2nx_leds[] in usb_mixer_interface
struct into the private_value of each kctl, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, we blindly assumed that the all usb-audio mixer elements
follow the standard and apply the standard resume method for the
registered elements in the id_elems[] list. However, some quirks
really need the own resume and it's incomplete for now.
This patch enhances the resume handling in two folds:
- split some fields in struct usb_mixer_elem_info into a smaller
header struct (usb_mixer_elem_list) for keeping the minimal
information in the linked-list; the usb_mixer_elem_info embeds this
header struct instead
- add resume and dump callbacks to usb_mixer_elem_list struct to allow
quirks providing the own methods
For the standard mixer elements, these new callbacks are set to the
standard ones as default, thus there is no functional change by this
patch yet.
The dump and resume callbacks are typedef'ed for ease of later patches
using arrays of such function pointers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The machine originally use the quirk ALC269_FIXUP_HP_GPIO_MIC1_LED,
but the LED doesn't work at all.
After this change, the machine will change to use
ALC269_FIXUP_HP_MUTE_LED_MIC1 through pin_fixup_tbl[], and the LED
works well.
BugLink: https://bugs.launchpad.net/bugs/1389497
Tested-by: TieFu Chen <tienfu.chen@canonical.com>
Cc: Kailang Yang <kailang@realtek.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New HP machine supported output mute led and input mute led.
ALC286:
GPIO1 to control output mute led.
GPIO5 to control input mute led.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce an internal helper macro for avoiding many open codes.
The only slight behavior change is in a couple of get ballcks where
the value is reset at error no matter whether ignore_ctl_error is set
or not. Actually this is even safer than before.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_nativeinstruments_control_get() uses a stack as a buffer for
usb_control_msg(), but it's basically not allowed. Replace the call
with a safer helper, snd_usb_ctl_msg(), instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are a few duplicated codes handling the mute and mic-mute LEDs
via GPIO pins. Let's consolidate to single helpers. Here we
introduced two new fields to alc_spec, gpio_mute_led_mask and
gpio_mic_led_mask, to contain the bit mask to set/clear. Also,
mute_led_polarity is evaluated as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The safeload feature allows to load up to 5 parameter memory registers
atomically. This is helpful for switching between e.g. filter settings
without causing any glitches.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the v2 version of the SigmaDSP firmware file
format. The new format has support for having different program and
parameter settings for different samplerates. In addition it stores metadata
describing the firmware. This metadata includes the set of supported
samplerates which will be used to restrict the samplerates that can be
selected by userspace. Also included is information about the modifiable
parameters. Those will be exposed as ALSA controls so they can be changed at
runtime.
The new format is based on a binary type-length-value structure that makes
it both forward and backwards compatible.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The v2 file format of the SigmaDSP takes a more declarative style compared
to the imperative style of the v1 format. In addition some features that are
supported with v2 require the driver to keep state around for the firmware.
This requires a bit of restructuring of both the firmware loader itself and
the drivers making use of the firmware loader.
Instead of loading and executing the firmware in place when the DSP is
configured the firmware is now loaded at driver probe time. This is required
since the new firmware format will in addition to the firmware data itself
contain meta information describing the firmware and its requirements and
capabilities. Those will for example be used to restrict the supported
samplerates advertised by the driver to userspace to the list of samplerates
supported for the firmware.
This only does the restructuring required by the v2 format, but does not
yet add support for the new format itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The official firmware generation tool never emitted any SIGMA_ACTION_DELAY
instructions. Keeping support for it with the new restructured loader that
also supports v2 will be difficult, so drop support for it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to check the version field of the firmware header to make sure to
not accidentally try to parse a firmware file with a different layout.
Trying to do so can result in loading invalid firmware code to the device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For ACPI we missed to pm_runtime_enable() call which is required to tell PM
core that runtime on this device is enabled now. Since this is common to
both PCI and APCI move it out. Also for ACPI we do not require
pm_runtime_allow() call, so remove that
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the regmap conversion ac97_read/ac97_write are just simple wrappers
around snd_soc_read/snd_soc_write. Use those instead directly and remove the
wrappers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch converts the ad1980 driver to use regmap for its IO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some drivers (most notably the AC'97 drivers) do not have access to their
regmap struct when the component/codec is registered. For those drivers the
automatic regmap setup will not work and needs to be done manually,
typically from the component/CODEC drivers probe callback.
This patch adds a set of helper function to handle deferred regmap
initialization as well as early regmap tear-down.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the slow charge of the vref in the end of the power sequences
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Follow the gpio naming rule to rename the irq function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many firmwares do not wait for the start bit before they begin
processing audio, whilst this is a bug on the firmware side there are
too many such firmwares in the wild to ignore the situation. This patch
moves the core enable to happen at same time as the start, the firmware
looses the ability to overlap its own startup with the audio path bring
up but we ensure that all firmwares behave.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Complete missing parameters, correct wrong reference, and add an explaination
about the differences between the latest specification and our implementation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: JS Park <aitdark.park@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
while building we were getting the following build warning:
Section mismatch in reference from the function rt286_i2c_probe()
to the variable .init.data:force_combo_jack_table
The function rt286_i2c_probe() references
the variable __initdata force_combo_jack_table.
This is often because rt286_i2c_probe lacks a __initdata
annotation or the annotation of force_combo_jack_table is wrong.
we were getting the warning as force_combo_jack_table was marked
with __initdata
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the ASoC core no longer needs a handle to the AC'97 device that is
associated with a CODEC we can remove it from the snd_soc_codec struct and
push it into the individual driver state structs like we do for other
communication buses. Doing so creates a clean separation between the AC'97
bus support and the ASoC core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting the ac97_control field on a CPU DAI tells the ASoC core that this
DAI in addition to audio data also transports control data to the CODEC.
This causes the core to suspend the DAI after the CODEC and resume it before
the CODEC so communication to the CODEC is still possible. This is not
necessarily something that is specific to AC'97 and can be used by other
buses with the same requirement. This patch renames the flag from
ac97_control to bus_control to make this explicit.
While we are at it also change the type from int to bool.
The following semantich patch was used for automatic conversion of the
drivers:
// <smpl>
@@
identifier drv;
@@
struct snd_soc_dai_driver drv = {
- .ac97_control
+ .bus_control
=
- 1
+ true
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is no longer necessary as there is no code anymore that uses this for
CODEC DAIs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have all the information and dependencies we need to initialize and
register the device available in snd_soc_new_ac97_codec(). So there is no
need to delay the device registration until after the card itself as been
registered.
This makes the code significantly simpler and also makes it possible to use
the AC'97 device in the CODECs probe function. The later will be required to
be able to convert the AC'97 CODEC drivers to regmap.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This has no users since commit f0fba2ad1b ("ASoC: multi-component - ASoC
Multi-Component Support") which was almost 5 years ago. Given that this runs
after CODEC probe functions have been run it also doesn't seem to be that
useful.
So drop it altogether to make the code simpler.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
soc_{un,}register_ac97_codec() is just a simple wrapper around
soc_ac97_dev_{un,}register(). There is no need to split these up into two
different sets of functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We always pass soc_ac97_ops to snd_soc_new_ac97_codec(). So instead of
allocating a snd_ac97_bus in snd_soc_new_ac97_codec() just use a static one
that gets initialized when snd_soc_set_ac97_ops() is called.
Also drop the device number parameter from snd_soc_new_ac97_codec(). We
currently only support one device per bus and all drivers pass 0 for the
device number. And if we should ever support multiple devices per bus it
wouldn't be up to individual AC'97 device drivers to pick their number, but
rather either the AC'97 adapter driver or the core code will assign them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the AC'97 support is splattered all throughout soc-core.c. Some
parts are #ifdef'd some parts are not. This patch moves the AC'97 support to
its own file, this should make the code a bit more clearer and also makes it
possible to easily not compile it into the kernel when not needed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The memory that a struct device is contained in must not be freed except
from within the device's release callback. The ASoC code currently does not
adhere to this rule for the AC'97 device. This patch fixes it by moving the
freeing of the AC'97 to the release callback and splitting up the
registration and unregistration of the device into separate steps for
getting/putting the reference to the device and adding/removing it to the
device hierarchy.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mpc5200_dma overwrites the private_data field of the CODEC's AC'97
device with the DMA drivers private data, but never actually reads it again.
Given that the private_data field is supposed to be owned by the AC'97
driver, overwriting it may cause undefined behavior. This patch removes the
code that overwrites the field from the driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mpc5200_psc_ac97 driver puts a snd_ac97 device on the stack in the
driver probe function, initializes the private data member of the device and
the never uses the device again. It should be safe to remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fix following errors while "make htmldocs" on
linux-next-20141110.
Warning(.//sound/soc/soc-jack.c:126): No description found for
parameter 'zones'
Warning(.//sound/soc/soc-jack.c:126): Excess function parameter
'zone' description in 'snd_soc_jack_add_zones'
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The microphone mute led on the Latitude E5550 can't work. We need to
apply DELL_WMI_MIC_MUTE_LED quirk to this machine.
The machine uses alc293 codec and already applied the quirk
ALC293_FIXUP_DELL1_MIC_NO_PRESENCE through pin_fixup_tbl[].
Here we just let DELL_WMI_MIC_MUTE_LED be chained to
ALC269_FIXUP_HEADSET_MODE, then the machine will have these
quirks ALC293_FIXUP_DELL1_MIC_NO_PRESENCE-->
ALC269_FIXUP_HEADSET_MODE-->ALC255_FIXUP_DELL_WMI_MIC_MUTE_LED.
BugLink: https://bugs.launchpad.net/bugs/1381856
Reported-and-tested-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have one more Dell machine needs DELL_WMI_MIC_MUTE_LED quirk, but
the machine uses alc293 instead of alc255. So if
DELL_WMI_MIC_MUTE_LED still chain ALC255_FIXUP_DELL1_MIC_NO_PRESENCE,
the machine can't use this quirk.
To change this situation, let the DELL_WMI_MIC_MUTE_LED to be a
standalone quirk, and let other quirks chain it.
After this change, this quirk can be chained to any existing quirks,
and as a result, it is possible that this quirk is applied to
a non-Dell machine or a Dell machine without mic mute led on it, but
it is still safe since alc_fixup_dell_wmi() will return an error in
these situations.
And remove the quirk for machine with subsystem id 0x6010 and 0x601f,
these two machines will fall back to the quirk
ALC255_FIXUP_DELL1_MIC_NO_PRESENCE-->ALC255_FIXUP_HEADSET_MODE-->
ALC255_FIXUP_DELL_WMI_MIC_MUTE_LED through pin_fixup_tbl[].
BugLink: https://bugs.launchpad.net/bugs/1381856
Reported-and-tested-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current driver can also run in I2S master mode, so remove the old comment.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify the default value of the MX-8E[4] to 1 for ASRC function. It could
prevent the pop noise with ASRC function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As well as the usual driver fixes there's a few other things here:
One is a fix for a race in DPCM which is unfortuantely a rather large
diffstat, this is the result of growing usage of the mainline code and
hence more detailed testing so I'm relatively happy.
The other is a fix for non-DT machine driver matching following some of
the componentization work which is much more focused.
Both have had a while to cook in -next.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUaifFAAoJECTWi3JdVIfQ9V0H/iE0R+vu2VyvTPt9PXcWNn2N
zCwwljFEc9p2tAKqCHXkq2JDZZDIUQBxQPMJF7m43iQ+JGg/6BjPnPCdNJsi7hZV
/prLtMUPhdExxRL/mdfvIS26FTHF3GhOZvE4ePAw/jJWlCCMWGt3iEruuoeDzbxg
TwHTlgVqBKcdDAAMe1kTkBCTcamt8SaLYOaAgICICJtwO6AFpf8UYrYnT4Y9l1XK
jOAPjfLNOtuIh0IKp7NBJlIdV3PZPpnx7l1wg8DN+63kwLStFrQjYvueu1UAArh8
Y65oQpkIxgqlJOvy59fY3J3F5HF9u6dWjtQv5wMOJm0Fr4y2GP+EsaHBlPYM0co=
=8pIU
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.18
As well as the usual driver fixes there's a few other things here:
One is a fix for a race in DPCM which is unfortuantely a rather large
diffstat, this is the result of growing usage of the mainline code and
hence more detailed testing so I'm relatively happy.
The other is a fix for non-DT machine driver matching following some of
the componentization work which is much more focused.
Both have had a while to cook in -next.
Fixes the following compilation warning:
Warning: 'rt5631_i2c_dt_ids' defined but not used - when DT is not used.
Signed-off-by: Claude Youn <claude.youn@gmail.com>
Signed-off-by: Krishna Mohan Dani <krishna.md@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should not free any buffers associated with writing out coefficients
to the DSP until all the async writes have completed. This patch updates
the out of memory path when allocating a new buffer to include a call to
regmap_async_complete.
Reported-by: JS Park <aitdark.park@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Specified in section 5.2.5.6.1 of the USB Audio Class 2.0 definition.
Solves the following error for C-Media 6632A (Asus Xonar U7):
[ 8219.676164] cannot get ctl value: req = 0x81, wValue = 0x0, wIndex = 0x1400, type = 3
Signed-off-by: Johan Rastén <johan@oljud.se>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pci_dev_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The release_firmware() function tests whether its argument is NULL and then
return immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The vfree() function performs also input parameter validation. Thus the test
around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd_ac97_resume() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The functions kfree() and release_firmware() test whether their argument
is NULL and then return immediately. Thus the test around the call
is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change clk_enable/disable() calls to clk_prepare_enable() and
clk_disable_unrepapre().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ACPI device table will generate the driver module alias for
Intel audio devices enumerated from ACPI.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a USB control message delay quirk for a few specific Marantz/Denon
devices. Without the delay the DACs will not work properly and produces the
following type of messages:
Nov 15 10:09:21 orwell kernel: [ 91.342880] usb 3-13: clock source 41 is not valid, cannot use
Nov 15 10:09:21 orwell kernel: [ 91.343775] usb 3-13: clock source 41 is not valid, cannot use
There are likely other Marantz/Denon devices using the same USB module which exhibit the
same problems. But as this cannot be verified I limited the patch to the devices
I could test.
The following two devices are covered by this path:
- Marantz SA-14S1
- Marantz HD-DAC1
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use vmalloc to allocate the buffer for firmware/coefficient download and
rely on the SPI core to split this up into DMA-able chunks. This should
give better performance and means we no longer need to manually split
the download into page size chunks to avoid allocating overly large
continuous memory regions.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
earlier we were ignoring the return value of snd_ak4114_create and
always returning 0.
now we are returning the actual status. revo_init is calling this
function, and revo_init is checking the return value.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
buf_size was initialized with snd_pcm_lib_buffer_bytes,
but never used. and so it is safe to be deleted.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
the functions:
snd_ice1712_akm4xxx_build_controls
snd_ice1712_build_pro_mixer
snd_ctl_add
snd_ak4114_build
prodigy192_ak4114_init
snd_ak4113_build
are all returning either 0 or a negetive error value.
so we can easily remove the check for a negative value and return
the value instead.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patah separate bias level off to standby and off. The standby
level will provide the necessary power for JD and push button
functions.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the last ACPI module support which also uses core module like the PCI
part
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TS3A227E is an autonomous audio accessory detection and
configuration switch that detects 3-pole or 4-pole audio accessories
and configures internal switches to route the signals accordingly.
This chip also has built-in support for the new button standard
described in the Android "Wired audio headset specification" v1.0.
These buttons will be reported on the jack as buttons 0-3 mapped to
KEY_MEDIA, KEY_VOLUMEUP, KEY_VOLUMEDOWN, and KEY_VOICE_COMMAND.
This will be added as an aux_dev and have the jack passed in from the
machine driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On a mx28evk with a sgtl5000 codec we notice a loud 'click' sound to happen
5 seconds after the end of a playback.
The SMALL_POP bit should fix this, but its definition is incorrect:
according to the sgtl5000 manual it is bit 0 of CHIP_REF_CTRL register, not
bit 1.
Fix the definition accordingly and enable the bit as intended per the code
comment.
After applying this change, no loud 'click' sound is heard after playback
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch adds the ACPI match ID for rt5670/5672 codec.
So on Intel CherryTrail/Braswell platforms, the codec can be enumerated from
ACPI and depends on ACPI to get platform-specific info and power saving.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Reviewed-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the inline function instead of directly indexing the array.
This allows some architectures with hardware instructions
for bit reversals to eliminate the array.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We need to set extra register to avoid a recording issue in TDM
mode.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lenovo Ideapad Z560 has a mute LED that is controlled via EAPD pin
0x1b on CX20585 codec. (EAPD bit on corresponds to mute LED on.)
The machine doesn't need other EAPD, so the fixup concentrates on
controlling EAPD 0x1b following the vmaster state (but inversely).
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=665315
Reported-by: Szymon Kowalczyk <fazerxlo@o2.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This code contains the Scarlett mixer interface code that was originally
written by Tobias Hoffman and Robin Gareus. Because the device doesn't
properly implement UAC2 this code adds a mixer quirk for the device.
Changes from the original code include removing the metering code along with
dead code and comments. Compiler warnings were fixed. The code to initialize
the sampling rate was causing a crash this was fixed as discussed on the
mailing list. Error, and info messages were convered to dev_err and dev_info
interfaces. The custom scarlett_mixer_elem_info struct was replaced with the
more generic usb_mixer_elem_info to be able to recycle more code from mixer.c.
This patch also makes additional modifications based on upstream comments.
Individual control creation functions are removed and a generic
function is no used. Macros for function calls are removed to improve
readability. Hardcoded control initialization is removed. Save to HW
functionality has been removed. Strings for enums are created dynamically for
the mixer. Strings used for controls are now SNDRV_CTL_ELEM_ID_NAME_MAXLEN
length.
Signed-off-by: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make the functions set_cur_mix_value and get_cur_mix_value accessible by files
that include mixer.h. In addition make usb_mixer_elem_free accessible.
This allows reuse of these functions by mixers that may require quirks.
The following summarizes the renamed functions:
- set_cur_mix_value -> snd_usb_set_cur_mix_value
- get_cur_mix_value -> snd_usb_get_cur_mix_value
- usb_mixer_elem_free -> snd_usb_mixer_elem_free
Signed-off-by: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a private_data pointer to usb_mixer_elem_info to allow other mixer
implementations to extend the structure as necessary.
Signed-off-by: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 1762a59d8e.
This quirk is not needed because support for the Scarlett mixers will be added.
Signed-off-by: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit a1253ef6d3 ("ASoC: cs42l51: split i2c from codec driver"),
the I2C part of the CS42L51 was moved to a separate file, but the
definition of the of_device_id array was left in the driver file
itself, no longer connected to the platform_driver structure using the
.of_match_table pointer.
This commit exports the of_device_id array in cs42l51, and uses it as
.of_match_able in cs42l51-i2c.c. This solution was suggested by Brian
Austin.
Fixes: a1253ef6d3 ("ASoC: cs42l51: split i2c from codec driver")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The new IPs supports a new lower frequency 768kHz DMIC operation
add support for this into the OSR control.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
An underrun (playback) event occurs when the serializer transfer
data from the XRBUF buffer to the XRSR shift register, but the
XRBUF hasn't been filled. Similarly, the overrun (capture) event
occurs when data from the XRSR shift register is transferred to
the XRBUF but it hasn't been read yet.
These events are handled as XRUN events that cause the pcm to stop.
The stream has to be explicitly restarted by the userspace which
ensures that after stopping/starting McASP the data transfer is
aligned with DMA. The other possibility was to internally stop and
start McASP without DMA even knowing about it.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This will fix no sound in Linux system after reboot from windows.
Change log:
- alc662_fill_coef() is replaced with alc_fill_eapd_coef_idx()
and move into alc_auto_init_amp().
- For ALC262, ALC267, ALC268, ALC269, ALC233, ALC255, ALC280, ALC282,
ALC283, ALC284, ALC285, ALC286, ALC288, ALC290, ALC292, ALC293, ALC294,
ALC668, ALC888VC, ALC888VD, ALC891, ALC892, ALC898 and ALC1150, add update
COEF control for EAPD setting.
- Remove alc269_fill_coef() for update EAPD control line.
ADDITIONAL NOTE:
Many Realtek cdoecs have a COEF bit to switch the master amp control
between COEF and EAPD. Windows drivers seem using COEF while we use
EAPD, which is more standard. As a result, some system suffer from
the silent output when booting after Windows. This patch sets the
COEF bits on the relevant codecs properly to switch to EAPD control.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=87771
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
M-audio FastTrack Ultra quirk doesn't release the kzalloc'ed memory.
This patch adds the private_free callback to release it properly.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch provides duplex support for the Digidesign Mbox 1 sound
card and has been a work in progress for about a year.
Users have confirmed on my website that previous versions of this patch
have worked on the hardware and I have been testing extensively.
It also enables the mixer control for providing clock source
selector based on the previous patch.
The sample rate has been hardcoded to 48kHz because it works better with
the S/PDIF sync mode when the sample rate is locked. This is the
highest rate that the device supports and no loss of functionality
is observed by restricting the sample rate apart from the inability to selec
a lower rate.
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch provides the infrastructure for the Digidesign Mbox 1
to have a mixer control for selecting the clock source.
Valid options are Internal and S/PDIF external sync.
A non-documented command is sent to the device to enable this feature
found by reverse engineering and bus snooping.
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Output driver has two parameters that can be configured to reduce
pop noise: power-on delay and ramp-up step time. Two new kcontrols
have been added to set these parameters.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is easier to find the relevant enums in the code. Use the
SOC_ENUM_*_DECL macro for the individual items.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove rt5645_clk_sel_put function since it is never used.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5672 is very similar to rt5670. Therefore we use one codec driver
to support both codecs. The difference between rt5670 and rt5672 is
there is some difference in their dapm routing table.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Needed due to some important regression fixes at RC core.
* commit 'v3.18-rc4': (587 commits)
Linux 3.18-rc4
ARM: dts: zynq: Enable PL clocks for Parallella
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
USB: Update default usb-storage delay_use value in kernel-parameters.txt
sysfs: driver core: Fix glue dir race condition by gdp_mutex
MIPS: Fix build with binutils 2.24.51+
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
USB: cdc-acm: add quirk for control-line state requests
tty: Fix pty master poll() after slave closes v2
MIPS: R3000: Fix debug output for Virtual page number
...
Conflicts:
drivers/media/rc/rc-main.c
Instead of registering the irq name with the driver name, it's better to pass
the device name so that we have a more explicit indication as to what saif
instance the irq is related:
$ cat /proc/interrupts
CPU0
...
214: 4 - 59 80042000.saif
215: 0 - 58 80046000.saif
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8962 uses the snd_soc_codec mutex to protect the wm8962_dsp2_ena_put()
function from concurrent execution. This patch moves that lock to the driver
level. This will allow us to eventually remove the snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8958 driver uses the snd_soc_codec mutex to protect the various
firmware pointers from concurrent assignment. This patch moves this lock to
the driver level. This will allow us to eventually remove the snd_soc_codec
mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8903 uses the snd_soc_codec mutex to protect its deemph settings from
concurrent access. This patch moves this lock to the driver level. This will
allow us to eventually remove the snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8731 uses the snd_soc_codec mutex to protect its deemph settings from
concurrent access. This patch moves this lock to the driver level. This will
allow us to eventually remove the snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm5102 driver currently uses the snd_soc_codec mutex to protect its
ultrasonic response settings from concurrent access. This patch moves this
lock to the driver level. This will allow us to eventually remove the
snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max98095 uses the snd_soc_codec mutex to protect against concurrent
access in some of its control put handlers. Move this mutex to the driver
level so we can eventually remove the snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ab8500 driver uses a driver specific lock to protect concurrent access
to some of the control put/get handlers and uses the snd_soc_codec mutex for
some others. This patch updates the driver to consistently use the driver
specific lock for all controls. This will allow us to eventually remove the
snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to cast the cpu_of_node or codec_of_node of the
dai_links when calling of_put_node.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Volume Ramp to Renesas sound driver.
amixer set "DVC Out" 100%
amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
amixer set "DVC Out Ramp" on
aplay xxx.wav &
amixer set "DVC Out" 80% // Volume Down
amixer set "DVC Out" 100% // Volume Up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Active slots count depends on the number of channels in the stream
and the number of active serializers. Each serializer will handle
at most the number of channels specified via 'tdm-slots' parameter
in DT.
There are two possible scenarios:
- Single serializer: channel count fits in the max slots supported by
McASP serializers, active slots is same as channel count
- Multiple serializers: channel count is bigger than max slots supported
by a serializer. Channel count determines how many serializers are
needed at their max slot count configuration
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In IIS (I2S, TDM, etc) mode the maximum number of allowed channels for
either direction can be:
number of serializers for the direction * tdm_slots.
This constraint applicable for the first stream, while consequent stream
should not have more channels then the first stream.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of validating the tdm_slots parameter every time at hw_params we
can do it once during probe. If the parameter is not valid (<2 or >32)
print an error and fix it up.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the bus is configured to have more BCLK then the data type demands we
need to use the rotation to move the data to correct place.
Reported-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In IIS mode the tx and rx configuration is symmetric, the BCLK and FSYNC is
shared.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas R-Car sound driver probe will be failed
if it try to use DMA mode and it couldn't use for some reasons.
But PIO mode works even though in such case.
This patch try to fallback to PIO mode if DMA mode probing was failed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas R-Car sound driver debug message
is using random format
(ex "ssi0: xxx" / "SSI0 xxx" / "ssi[0]: xxx")
and confusable timing
("xxx probe failed" and "xxx probed" are shown in same time)
This patch fixes these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If probe fails then we need to call pm_runtime_disable() to balance
out the previous pm_runtime_enable() call.
Signed-off-by: Anil Kumar <anilk4.v@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With device tree, it is possible (and encouraged) to build N900
kernels without CONFIG_MACH_NOKIA_RX51. Update config file to enable
the driver build in this case.
This makes sound work on my n900 under 3.18-rc1.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
TDM support is achieved using DSP transfer mode and setting a
programmable offset which specifies where data begins with
respect to the frame sync.
It requires 256-clock mode if CODEC is master (not currently
supported in the driver). No additional dependency if CODEC
is slave.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The quirk argument itself was used as iterator, so it cannot be taken
back to the original value, obviously.
Fixes: d4b8fc66f7 ('ALSA: usb-audio: Allow multiple entries for the same iface in composite quirk')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a copy & paste error:
Warning(sound/core/pcm_native.c:1112): Excess function parameter 'state' description in 'snd_pcm_stop_xrun'
The state argument was dropped from snd_pcm_stop_xrun().
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the composite quirk doesn't work when multiple entries are
assigned to the same interface because it marks the interface as
claimed then checks whether the interface has been already claimed for
the secondary entry. But, if you look at the code, you'll notice that
multiple entries are allowed if the entry is the current interface;
i.e. the current behavior is anyway inconsistent, and this is an
unintended shortcoming.
This patch fixes the problem by marking the relevant interfaces as
claimed after applying the all composite entries. This fix will be
needed for the upcoming enhancements for Digidesign Mbox 1 quirks.
Reviewed-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new helper function snd_pcm_stop_xrun() to the standard sequnce
lock/snd_pcm_stop(XRUN)/unlock by a single call, and replace the
existing open codes with this helper.
The function checks the PCM running state to prevent setting the wrong
state, too, for more safety.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This function has no more non regmap user, which means we can remove the
implementation of the function and associated functions and structure
fields.
For convenience we keep a static inline version of the function that
forwards calls to regcache_sync() unconditionally.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
For convenience for drivers that do not want to keep their own pointer to
regmap struct around forward calls to snd_soc_cache_sync() to
regcache_sync() if the driver is using regmap. This is similar to what we do
for snd_soc_read()/snd_soc_write().
This patch also fixes drivers which already have been converted to regmap,
but still use snd_soc_cache_sync() for trying to the sync the cache.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm9712/wm9713 has separate mixers for the left and the right channel,
but the inputs to the mixers are enabled/disabled by the same control.
Currently this is implemented by the driver by registering two virtual
controls for each physical control, one for the left mixer and one for the
right mixer.
Using virtual registers will no longer work when the driver has
been converted to regmap. This patch converts the driver to use controls
with custom put/get callbacks instead which implement the logic making sure
that the physical control is unmuted when either the left or the right
control is unmuted.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We want to know the offset for the id that was passed to the function, not
the offset of the first id of the control (which is always 0).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jie Yang
Takashi Iwai
Fabio Estevam
Lars-Peter Clausen
Dan Carpenter
Zidan Wang
Krishna Mohan Dani
Jean-Francois Moine
Nicolin Chen
Oder Chiou
Bard Liao
kbuild test robot
Andreas Ruprecht
Jyri Sarha
Jarkko Nikula
Benjamin Herrenschmidt
Eliot Blennerhassett
Qiao Zhou
Mengdong Lin
Markus Elfring
Padmavathi Venna
Jussi Laako
Hui Wang
Kailang Yang
Subhransu S. Prusty
Vinod Koul
Mark Brown
Charles Keepax
Takashi Sakamoto
JS Park
Sudip Mukherjee
Masanari Iida
Johan Rastén
Dmitry Eremin-Solenikov
Jurgen Kramer
Dylan Reid
Joe Perches
Chris J Arges
Richard Fitzgerald
Thomas Petazzoni
Misael Lopez Cruz
Damien Zammit
Peter Ujfalusi
Mauro Carvalho Chehab
Kuninori Morimoto
Anil Kumar
Pavel Machek
Peter Rosin
Devin Ryles