This fixes a bit error in the U8500 clock implementation: the
unused p2_pclk12 registered at bit 12 in periphereral group 6
was defined as using bit 11 rather than bit 12.
When walking over and disabling the unused clocks in the tree
at late init time, p2_pclk12 was disabled, by effectively
clearing the but for p2_pclk11 instead of bit 12 as it should
have, thus disabling gpio block 6 and 7.
Reported-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Philippe Begnic <philippe.begnic@st.com>
Cc: stable@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
When a clock, C is initialised any orphan clocks listing C as
a possible parent are reparented to it regardless of the
parent requested by the orphan's get_parent() operation.
This means that multiplexers registered before their parents
are reparented to the first parent subsequently declared,
regardless of the selection made by the hardware registers.
For example:
static const char *sel[] = { "srcA", "srcB", "dummy", "srcC" };
child = clk_register_mux(NULL, "child", sel, ARRAY_SIZE(sel), ...);
clk_register_fixed(NULL, "dummy", ...);
clk_register_fixed(NULL, "srcA", ...);
clk_register_fixed(NULL, "srcB", ...);
clk_register_fixed(NULL, "srcC", ...);
Causes child's parent to always be "dummy".
To fix this, when an orphanned clock has a get_parent() operation,
only reparent to the clock indicated by get_parent().
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: improve $SUBJECT]
The abx500 clock driver is a platform driver which will be initialized
during arch init. The platform device shall be added from the ab-core
driver as a mfd child device to maintain correct boot sequence.
Depending on what ab version we use, different clock definitions will
be added.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Dummy clocks were added for ARM platforms, so that clk_get() for interface clk
doesn't fail for amba devices from amba_probe(). Because there is no amba device
for SPEAr that doesn't have a valid clock with dev_id for SPEAr, we don't need
these dummy clocks. Hence, remove them.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The patch corrects the case when the rate table is being scanned for a
given frequency, and the search frequency is beyond the maximum
frequency indexed in the table.
By default, the system should be set at max frequency present in the
rate table. This patch correctly returns the corresponding index value.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Flag CLK_SET_RATE_PARENT is required for a clock, where we want to
propagate clk_set_rate to its parent. This patch adds this to multiple clocks.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Vijay Kumar Mishra <vijay.kumar@st.com>
Signed-off-by: Vijay Kumar Mishra <vijay.kumar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch updates mux clock names of multiple clocks. It updates _clk with
_mclk to make it more readable.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
dev_id & con_id names of multiple clocks are incorrect. This patch fixes these
names with the names that come via DT.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Bhavna Yadav <bhavna.yadav@st.com>
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The ARM IM-PD1 add-on module has a few clock of its own, let's
move also these down to the drivers/clk/versatile driver dir
and get rid of any remaining oldschool Integrator clocks.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
It turns out that all platforms using the ICST VCO are really
just touching two registers, and in the same way as well: one
register with the VCO configuration as such, and one lock register
that makes it possible to write to the VCO.
Factor this register read/write into the ICST driver so we can
reuse it in the IM-PD1 driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The GPLv2 headers were missing and the subsystem maintainer likes
them so put them in. I am the copyright holder, so explicitly
licensing these under the GPLv2.
Reported-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Use a better name for the USB PHY clock.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This fixes compile error if one of SPEAr3xx implementations is not selected.
CC drivers/clk/spear/spear3xx_clock.o
drivers/clk/spear/spear3xx_clock.c: In function 'spear3xx_clk_init':
drivers/clk/spear/spear3xx_clock.c:599:3: error: implicit declaration of function 'spear300_clk_init' [-Werror=implicit-function-declaration]
drivers/clk/spear/spear3xx_clock.c:601:3: error: implicit declaration of function 'spear310_clk_init' [-Werror=implicit-function-declaration]
drivers/clk/spear/spear3xx_clock.c:603:3: error: implicit declaration of function 'spear320_clk_init' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [drivers/clk/spear/spear3xx_clock.o] Error 1
make[2]: *** [drivers/clk/spear] Error 2
make[1]: *** [drivers/clk] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In case of error, the function clk_register() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
At the same time the prcc bit for the kclk is corrected to
bit 8 instead of 3.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds some additional handling for the SDMMC special case
in round_rate and set_rate which results in invalid divisor messages
at boot time.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In case of error, the function clk_register_fixed_rate() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Using the armss clk to update the frequency makes the driver no more
directly dependant on the prmcu API.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The new armss clk is a prcmu_scalable_rate clk which represents
the ARMSS clk. This then makes it possible to convert the smp_twd
clk to a fixed factor clock type, using a fixed divider of 2 and
with the armss clk as parent.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The prcmu_scalable_rate clock can change rate but is not gateable.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
ARMSS clk directly maps it's frequency towards the cpufreq table.
To be able to update the ARMSS clk rate, a new set_rate function for
the ARMSS clk is added, which also will trigger a corresponding ARM
OPP request. Additionally an ARMSS clk round_rate function is added
to fetch valid cpufreq frequencies.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
By fetching the table as platform data we do not need the internally
hardcoded cpufreq table anymore.
Moreover the corresponding arm_opp idx2opp table, used for mapping
frequency to correct opp bits is also removed. This due to that the
opp bits is put directly in the index field of the cpufreq table.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
To fetch the mfd child device we register the cpufreq driver
as a platform driver.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The cpufreq table needs dynamically update due to what the PRCMU
firmware is supporting. The table is then provided through to the
mfd child device as platform data.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Move this driver to use devm_clk_register() to simplify some
error paths and reduce lines of code.
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some clock drivers can be simplified if devres takes care of
unregistering any registered clocks along error paths. Introduce
devm_clk_register() so that clock drivers get unregistration for
free along with simplified error paths.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_register() returns an ERR_PTR upon failure, not NULL. Fix
these error paths.
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds a DT and non-DT based implementation of
the common clock infrastructure for Versatile Express
platform. It registers (statically or using DT) all
required fixed clocks, initialises motherboard's SP810
cell (that provides clocks for SP804 timers) and
explicitly registers VE "osc" driver, to make the
clock generators available early.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This driver provides a common clock framework hardware driver
for Versatile Express clock generators (a.k.a "osc") controlled
via the config bus.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
On OMAP4+ platforms the functional clock for the McPDM IP is suplied by
the twl6040 codec (bit clock on the PDM bus).
This common clock driver for twl6040 will register the mcpdm_fclk clock to
be used by the McPDM driver to make sure that the needed clocks are
available when needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In case of error, the function clk_register() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In case of error, the function clk_register_fixed_rate() returns
ERR_PTR() not NULL pointer. The NULL test in the return value
check should be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
For u8500 and using 100MHz as the frequency also requires the ape opp 100
voltage, thus use the prcmu_opp_volt_scalable clock type.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some scalable prcmu clocks needs to be handled in conjuction with the
ape opp 100 voltage. A new prcmu clock type clk_prcmu_opp_volt_scalable
is implemented to handle this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This function needs to be exported to let clients be able to
request the ape opp 100 voltage.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some of the helper functions return negative error codes if
passed a NULL clock. This can lead to confusing behavior when the
expected return value is unsigned. Fix up these accessors so that
they return unsigned values (or bool in the case of is_enabled).
This way we can't interpret NULL clocks as having valid and
interesting values.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Currently we are getting following warning for SPEAr clk-vco-pll.
"warning: i is used uninitialized in this function."
This is because we are getting value of i by passing its pointer to another
routine.
The variables here are really not used uninitialized.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
These fixes are both pretty minor ones and are driver local.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=3xEy
-----END PGP SIGNATURE-----
Merge tag 'spi-mxs' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull minor spi MXS fixes from Mark Brown:
"These fixes are both pretty minor ones and are driver local."
* tag 'spi-mxs' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
spi: mxs: Terminate DMA in case of DMA timeout
spi: mxs: Assign message status after transfer finished
Pull networking fixes from David Miller:
"This is what we usually expect at this stage of the game, lots of
little things, mostly in drivers. With the occasional 'oops didn't
mean to do that' kind of regressions in the core code."
1) Uninitialized data in __ip_vs_get_timeouts(), from Arnd Bergmann
2) Reject invalid ACK sequences in Fast Open sockets, from Jerry Chu.
3) Lost error code on return from _rtl_usb_receive(), from Christian
Lamparter.
4) Fix reset resume on USB rt2x00, from Stanislaw Gruszka.
5) Release resources on error in pch_gbe driver, from Veaceslav Falico.
6) Default hop limit not set correctly in ip6_template_metrics[], fix
from Li RongQing.
7) Gianfar PTP code requests wrong kind of resource during probe, fix
from Wei Yang.
8) Fix VHOST net driver on big-endian, from Michael S Tsirkin.
9) Mallenox driver bug fixes from Jack Morgenstein, Or Gerlitz, Moni
Shoua, Dotan Barak, and Uri Habusha.
10) usbnet leaks memory on TX path, fix from Hemant Kumar.
11) Use socket state test, rather than presence of FIN bit packet, to
determine FIONREAD/SIOCINQ value. Fix from Eric Dumazet.
12) Fix cxgb4 build failure, from Vipul Pandya.
13) Provide a SYN_DATA_ACKED state to complement SYN_FASTOPEN in socket
info dumps. From Yuchung Cheng.
14) Fix leak of security path in kfree_skb_partial(). Fix from Eric
Dumazet.
15) Handle RX FIFO overflows more resiliently in pch_gbe driver, from
Veaceslav Falico.
16) Fix MAINTAINERS file pattern for networking drivers, from Jean
Delvare.
17) Add iPhone5 IDs to IPHETH driver, from Jay Purohit.
18) VLAN device type change restriction is too strict, and should not
trigger for the automatically generated vlan0 device. Fix from Jiri
Pirko.
19) Make PMTU/redirect flushing work properly again in ipv4, from
Steffen Klassert.
20) Fix memory corruptions by using kfree_rcu() in netlink_release().
From Eric Dumazet.
21) More qmi_wwan device IDs, from Bjørn Mork.
22) Fix unintentional change of SNAT/DNAT hooks in generic NAT
infrastructure, from Elison Niven.
23) Fix 3.6.x regression in xt_TEE netfilter module, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
tilegx: fix some issues in the SW TSO support
qmi_wwan/cdc_ether: move Novatel 551 and E362 to qmi_wwan
net: usb: Fix memory leak on Tx data path
net/mlx4_core: Unmap UAR also in the case of error flow
net/mlx4_en: Don't use vlan tag value as an indication for vlan presence
net/mlx4_en: Fix double-release-range in tx-rings
bas_gigaset: fix pre_reset handling
vhost: fix mergeable bufs on BE hosts
gianfar_ptp: use iomem, not ioports resource tree in probe
ipv6: Set default hoplimit as zero.
NET_VENDOR_TI: make available for am33xx as well
pch_gbe: fix error handling in pch_gbe_up()
b43: Fix oops on unload when firmware not found
mwifiex: clean up scan state on error
mwifiex: return -EBUSY if specific scan request cannot be honored
brcmfmac: fix potential NULL dereference
Revert "ath9k_hw: Updated AR9003 tx gain table for 5GHz"
ath9k_htc: Add PID/VID for a Ubiquiti WiFiStation
rt2x00: usb: fix reset resume
rtlwifi: pass rx setup error code to caller
...
Pull slave-dmaengine fixes from Vinod Koul:
"Three fixes for slave dmanegine.
Two are for typo omissions in sifr dmaengine driver and the last one
is for the imx driver fixing a missing unlock"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: sirf: fix a typo in moving running dma_desc to active queue
dmaengine: sirf: fix a typo in dma_prep_interleaved
dmaengine: imx-dma: fix missing unlock on error in imxdma_xfer_desc()
* Fix for a memory leak in acpi_bind_one() from Jesper Juhl.
* Fix for an error code path memory leak in pm_genpd_attach_cpuidle()
from Jonghwan Choi.
* Fix for smp_processor_id() usage in preemptible code in powernow-k8 from
Andreas Herrmann.
* Fix for a suspend-related memory leak in cpufreq stats from Xiaobing Tu.
* Freezer fix for failure to clear PF_NOFREEZE along with PF_KTHREAD
in flush_old_exec() from Oleg Nesterov.
* acpi_processor_notify() fix from Alan Cox.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8Tcc
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael J Wysocki:
- Fix for a memory leak in acpi_bind_one() from Jesper Juhl.
- Fix for an error code path memory leak in pm_genpd_attach_cpuidle()
from Jonghwan Choi.
- Fix for smp_processor_id() usage in preemptible code in powernow-k8
from Andreas Herrmann.
- Fix for a suspend-related memory leak in cpufreq stats from Xiaobing
Tu.
- Freezer fix for failure to clear PF_NOFREEZE along with PF_KTHREAD in
flush_old_exec() from Oleg Nesterov.
- acpi_processor_notify() fix from Alan Cox.
* tag 'pm+acpi-for-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: missing break
freezer: exec should clear PF_NOFREEZE along with PF_KTHREAD
Fix memory leak in cpufreq stats.
cpufreq / powernow-k8: Remove usage of smp_processor_id() in preemptible code
PM / Domains: Fix memory leak on error path in pm_genpd_attach_cpuidle
ACPI: Fix memory leak in acpi_bind_one()
Linus Walleij
Martin Fuzzey
Ulf Hansson
Vipul Kumar Samar
Deepak Sikri
Shiraz Hashim
Rajeev Kumar
Fabio Estevam
Axel Lin
Wei Yongjun
Tony Prisk
Stephen Boyd
Pawel Moll
Peter Ujfalusi
Viresh Kumar
Linus Torvalds