A few PHY drivers have the GPLv2 license text. They then either have
a MODULE_LICENSE() of GPLv2+, or an SPDX tag of GPLv2+.
Since the license text is much easier to understand than either the
SPDX tag or the MODULE_LICENSE, use it as the definitive source of the
licence, and fixup with others when there are contradictions.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Laurent Pinchart <laurentp@cse-semaphore.com>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 6390 Ethernet switch family does not perform MDIO
turnaround correctly. Many hardware MDIO bus masters don't care about
this, but the bitbangging implementation in Linux does by default. Add
phy_ignore_ta_mask to the platform data so that the bitbangging code
can be told which devices are known to get TA wrong.
v2
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is sometimes necessary to instantiate a bit-banging MDIO bus as a
platform device, without the aid of device tree.
When device tree is being used, the bus is not scanned for devices,
only those devices which are in device tree are probed. Without device
tree, by default, all addresses on the bus are scanned. This may then
find a device which is not a PHY, e.g. a switch. And the switch may
have registers containing values which look like a PHY. So during the
scan, a PHY device is wrongly created.
After the bus has been registered, a search is made for
mdio_board_info structures which indicates devices on the bus, and the
driver which should be used for them. This is typically used to
instantiate Ethernet switches from platform drivers. However, if the
scanning of the bus has created a PHY device at the same location as
indicated into the board info for a switch, the switch device is not
created, since the address is already busy.
This can be avoided by setting the phy_mask of the mdio bus. This mask
prevents addresses on the bus being scanned.
v2
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until commit 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod
functions where possible"), the _cansleep variants of the gpio_ API was
used. After that commit and the change to gpiod_ API, the _cansleep()
was dropped. This then results in WARN_ON() when used with GPIO
devices which do sleep. Add back the _cansleep() to avoid this.
Fixes: 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod functions where possible")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit re-enables support for slow GPIO pins. It was initially
introduced by commit 2d6c9091ab ("net: mdio-gpio: support access that
may sleep") and got lost by commit 7e5fbd1e07 ("net: mdio-gpio:
Convert to use gpiod functions where possible").
Also add a warning about slow GPIO pins like it is done in i2c-gpio.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO MDIO driver now needs only <linux/gpio/consumer.h>
so cut the legacy <linux/gpio.h> and <linux/of_gpio.h>
includes that are no longer used.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers have the following pattern:
if (np)
of_mdiobus_register()
else
mdiobus_register()
which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform data header file is now unused. Remove it, but add
an extra include which it brought in.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIOs are described in device tree using a list, without names.
Add defines to indicate what each index in the list means. These
defines should also be used by platform devices passing GPIOs via a
GPIO lookup table.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same parsing code can be used for both OF and platform devices, if
the platform device uses a gpiod_lookup_table. Parse these properties
directly into the bitbang structure, rather than use an intermediate
platform data structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving the allocation of this structure to the probe function is a
step towards making it the core data structure of the driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies the code, removing the need to handle active low
flags, etc.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
No current devices use IRQs in platform data, so remove support for
it. The MDIO core will also initialise the new bus such that all
addresses are polled, so remove the unneeded re-initialisation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not needed any more by devices using platform data, so remove
it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not needed any more by devices using platform data, so remove
it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform data can contain a function to call to reset
the bit banging interface. It is not used, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make this const as it is only stored in a const field of a
mdiobb_ctrl structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
gpiod functions support handling low-active pins, so we can move
thos code out of this driver into the gpio subsystem and simplify
the code a bit.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using gpiod functions lets us use functionality which is not available
with gpio functions.
There is no gpiod function to match devm_gpio_request_one, so leave it
in place and use gpio_to_desc() to convert absolute pin numbers to gpio
descriptors.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using devm_gpio_request_one lets us request gpio pins with initial state
in one go.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This header file only contains the platform data structure definition,
so move it to the include/linux/platform_data/ directory.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also changes mii_bus.phy_mask to u32 for consistency.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bus id was supplied via a struct platform_device, the driver wasn't
handling -1 to mean an unspecified id of the only instance of this driver,
as the platform spec requires.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some systems using mdio-gpio may use gpio on message based busses, which
require sleeping (e.g. gpio from an I2C I/O expander).
Since this driver does not use IRQ handler, it is safe to use the
_cansleep suffixed gpio accessors.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a sane default bus id (rather than -ENODEV) and print a warning when
the bus alias id is missing.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is for a system with fixed assignments of input and output pins
(various variants of Kontron COMe).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some systems using mdio-gpio may use active-low gpio pins
(eg with inverters or FETs connected to all or some of the
gpio pins).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies error path and deinit/removal functions.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_platform_driver macro removes some boilerplate and
simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.
Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the mdio-gpio driver is probed via device trees, the platform
device id is set as -1, However the pdev->id is re-used as bus-id for
while creating mdio gpio bus.
So
For device tree case the mdio-gpio bus name appears as "gpio-ffffffff"
where as
for non-device tree case the bus name appears as "gpio-<bus-num>"
Which means the bus_id is fixed in device tree case, so we can't have
two mdio gpio buses via device trees. Assigning a logical bus number
via device tree solves the problem and the bus name is much consistent
with non-device tree bus name.
Without this patch
1. we can't support two mdio-gpio buses via device trees.
2. we should always pass gpio-ffffffff as bus name to phy_connect, very
different to non-device tree bus name.
So, setting up the bus_id via aliases from device tree is the right
solution and other drivers do similar thing.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the way device tree support is added in mdio-gpio
driver. I found lot of code duplication which is not necessary.
Also strangely a new platform driver was also introduced for device tree
support. All this forced me to do this cleanup patch.
After this patch, the driver probe checks the of_node pointer to get the
data from device tree.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the x86-specific definition of irq_domain and replaces
it with the common implementation.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
This patch adds phy reset functionality to mdio-gpio driver. Now
mdio_gpio_platform_data has new member as function pointer which can be
filled at the bsp level for a callback from phy infrastructure. Also the
mdio-bitbang driver fills-in the reset function of mii_bus structure.
Without this patch the bsp level code has to takecare of the reseting
PHY's on the bus, which become bit hacky for every bsp and
phy-infrastructure is ignored aswell.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
"7488876... dt/net: Eliminate users of of_platform_{,un}register_driver"
there are two platform drivers named "mdio-gpio" registered.
I renamed the of variant to "mdio-ofgpio".
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of users of of_platform_driver in drivers/net. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This fixes the following warning:
WARNING: drivers/net/phy/built-in.o(.devexit.text+0x70): Section mismatch in reference from the function .mdio_gpio_bus_destroy() to the function .devinit.text:.mdio_gpio_bus_deinit()
The function __devexit .mdio_gpio_bus_destroy() references
a function __devinit .mdio_gpio_bus_deinit().
This is often seen when error handling in the exit function
uses functionality in the init path.
The fix is often to remove the __devinit annotation of
.mdio_gpio_bus_deinit() so it may be used outside an init section.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn
Martin Schiller
David S. Miller
Linus Walleij
Florian Fainelli
Bhumika Goyal
Guenter Roeck
Vivien Didelot
Luis de Bethencourt
Bert Vermeulen
Fabian Frederick
Wolfram Sang
Johan Hovold
Paul Gortmaker
Jingoo Han
Sachin Kamat
Greg Kroah-Hartman
Bill Pemberton
Srinivas Kandagatla
Grant Likely
Florian Fainelli
Dirk Eibach
Stephen Rothwell