This is a left over of how we used to wait for ordered extents, which was to
grab the inode and then run filemap flush on it. However if we have an ordered
extent then we already are holding a ref on the inode, and we just use
btrfs_start_ordered_extent anyway, so there is no reason to have an extra ref on
the inode to start work on the ordered extent. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
We currently have this problem where you can truncate pages that have not yet
been written for an ordered extent. We do this because the truncate will be
coming behind to clean us up anyway so what's the harm right? Well if truncate
fails for whatever reason we leave an orphan item around for the file to be
cleaned up later. But if the user goes and truncates up the file and tries to
read from the area that had been discarded previously they will get a csum error
because we never actually wrote that data out.
This patch fixes this by allowing us to either discard the ordered extent
completely, by which I mean we just free up the space we had allocated and not
add the file extent, or adjust the length of the file extent we write. We do
this by setting the length we truncated down to in the ordered extent, and then
we set the file extent length and ram bytes to this length. The total disk
space stays unchanged since we may be compressed and we can't just chop off the
disk space, but at least this way the file extent only points to the valid data.
Then when the file extent is free'd the extent and csums will be freed normally.
This patch is needed for the next series which will give us more graceful
recovery of failed truncates. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
u64 is "unsigned long long" on all architectures now, so there's no need to
cast it when formatting it using the "ll" length modifier.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
I added a patch where we started taking the ordered operations mutex when we
waited on ordered extents. We need this because we splice the list and process
it, so if a flusher came in during this scenario it would think the list was
empty and we'd usually get an early ENOSPC. The problem with this is that this
lock is used in transaction committing. So we end up with something like this
Transaction commit
-> wait on writers
Delalloc flusher
-> run_ordered_operations (holds mutex)
->wait for filemap-flush to do its thing
flush task
-> cow_file_range
->wait on btrfs_join_transaction because we're commiting
some other task
-> commit_transaction because we notice trans->transaction->flush is set
-> run_ordered_operations (hang on mutex)
We need to disentangle the ordered operations flushing from the delalloc
flushing, since they are separate things. This solves the deadlock issue I was
seeing. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Using the structure btrfs_sector_sum to keep the checksum value is
unnecessary, because the extents that btrfs_sector_sum points to are
continuous, we can find out the expected checksums by btrfs_ordered_sum's
bytenr and the offset, so we can remove btrfs_sector_sum's bytenr. After
removing bytenr, there is only one member in the structure, so it makes
no sense to keep the structure, just remove it, and use a u32 array to
store the checksum value.
By this change, we don't use the while loop to get the checksums one by
one. Now, we can get several checksum value at one time, it improved the
performance by ~74% on my SSD (31MB/s -> 54MB/s).
test command:
# dd if=/dev/zero of=/mnt/btrfs/file0 bs=1M count=1024 oflag=sync
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
The reason we introduce per-subvolume ordered extent list is the same
as the per-subvolume delalloc inode list.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
It is very likely that there are several blocks in bio, it is very
inefficient if we get their csums one by one. This patch improves
this problem by getting the csums in batch.
According to the result of the following test, the execute time of
__btrfs_lookup_bio_sums() is down by ~28%(300us -> 217us).
# dd if=<mnt>/file of=/dev/null bs=1M count=1024
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
We need to hold the ordered_operations mutex while waiting on ordered extents
since we splice and run the ordered extents list. We need to make sure anybody
else who wants to wait on ordered extents does actually wait for them to be
completed. This will keep us from bailing out of flushing in case somebody is
already waiting on ordered extents to complete. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Miao made the ordered operations stuff run async, which introduced a
deadlock where we could get somebody (sync) racing in and committing the
transaction while a commit was already happening. The new committer would
try and flush ordered operations which would hang waiting for the commit to
finish because it is done asynchronously and no longer inherits the callers
trans handle. To fix this we need to make the ordered operations list a per
transaction list. We can get new inodes added to the ordered operation list
by truncating them and then having another process writing to them, so this
makes it so that anybody trying to add an ordered operation _must_ start a
transaction in order to add itself to the list, which will keep new inodes
from getting added to the ordered operations list after we start committing.
This should fix the deadlock and also keeps us from doing a lot more work
than we need to during commit. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
btrfs_run_ordered_operations() needn't traverse the ordered operation list
repeatedly, it is because the transaction commiter will invoke it again when
there is no other writer in this transaction, it can ensure that no one can
add new objects into the ordered operation list.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Since we don't actually copy the extent information from the source tree in
the fast case we don't need to wait for ordered io to be completed in order
to fsync, we just need to wait for the io to be completed. So when we're
logging our file just attach all of the ordered extents to the log, and then
when the log syncs just wait for IO_DONE on the ordered extents and then
write the super. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
We specifically do not update the disk i_size if there are ordered extents
outstanding for any area between the current disk_i_size and our ordered
extent so that we do not expose stale data. The problem is the check we
have only checks if the ordered extent starts at or after the current
disk_i_size, which doesn't take into account an ordered extent that starts
before the current disk_i_size and ends past the disk_i_size. Fix this by
checking if the extent ends past the disk_i_size. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
If we have an ordered extent before the ordered extent we are currently
completing that is after the current disk_i_size we will put our i_size
update into that ordered extent so that we do not expose stale data. The
problem is that if our disk i_size is updated past the previous ordered
extent we won't update the i_size with the pending i_size update. So check
the pending i_size update and if its above the current disk i_size we need
to go ahead and try to update. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Though the process of the ordered extents is a bit different with the delalloc inode
flush, but we can see it as a subset of the delalloc inode flush, so we also handle
them by flush workers.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
The process of the ordered operations is similar to the delalloc inode flush, so
we handle them by flush workers.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
The ordered extent allocation is in the fast path of the IO, so use a slab
to improve the speed of the allocation.
"Size of the struct is 280, so this will fall into the size-512 bucket,
giving 8 objects per page, while own slab will pack 14 objects into a page.
Another benefit I see is to check for leaked objects when the module is
removed (and the cache destroy takes place)."
-- David Sterba
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
If a snapshot is created while we are writing some data into the file,
the i_size of the corresponding file in the snapshot will be wrong, it will
be beyond the end of the last file extent. And btrfsck will report:
root 256 inode 257 errors 100
Steps to reproduce:
# mkfs.btrfs <partition>
# mount <partition> <mnt>
# cd <mnt>
# dd if=/dev/zero of=tmpfile bs=4M count=1024 &
# for ((i=0; i<4; i++))
> do
> btrfs sub snap . $i
> done
This because the algorithm of disk_i_size update is wrong. Though there are
some ordered extents behind the current one which we use to update disk_i_size,
it doesn't mean those extents will be dealt with in the same transaction. So
We shouldn't use the offset of those extents to update disk_i_size. Or we will
get the wrong i_size in the snapshot.
We fix this problem by recording the max real i_size. If we find there is a
ordered extent which is in front of the current one and doesn't complete, we
will record the end of the current one into that ordered extent. Surely, if
the current extent holds the end of other extent(it must be greater than
the current one because it is behind the current one), we will record the
number that the current extent holds. In this way, we can exclude the ordered
extents that may not be dealth with in the same transaction, and be easy to
know the real disk_i_size.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
The pdflush thread is long gone, so this patch removes references to pdflush
from btrfs comments.
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: linux-btrfs@vger.kernel.org
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
I removed this in an earlier commit and I was wrong. Because compression
can return from filemap_fdatawrite() without having actually set any of it's
pages as writeback() it can make filemap_fdatawait() do essentially nothing,
and then we won't find any ordered extents because they may not have been
created yet. So not only does this make fsync() completely useless, but it
will also screw up if you truncate on a non-page aligned offset since we
zero out the end and then wait on ordered extents and then call drop caches.
We can drop the cache before the io completes and then we try to unpin the
extent we just wrote we won't find it and everything goes sideways. So fix
this by putting it back and put a giant comment there to keep me from trying
to remove it in the future. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
We noticed that the ordered extent completion doesn't really rely on having
a page and that it could be done independantly of ending the writeback on a
page. This patch makes us not do the threaded endio stuff for normal
buffered writes and direct writes so we can end page writeback as soon as
possible (in irq context) and only start threads to do the ordered work when
it is actually done. Compression needs to be reworked some to take
advantage of this as well, but atm it has to do a find_get_page in its endio
handler so it must be done in its own thread. This makes direct writes
quite a bit faster. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
We are checking delalloc to see if it is ok to update the i_size. There are
2 cases it stops us from updating
1) If there is delalloc between our current disk_i_size and this ordered
extent
2) If there is delalloc between our current ordered extent and the next
ordered extent
These tests are racy however since we can set delalloc for these ranges at
any time. Also for the first case if we notice there is delalloc between
disk_i_size and our ordered extent we will not update disk_i_size and assume
that when that delalloc bit gets written out it will update everything
properly. However if we crash before that we will have file extents outside
of our i_size, which is not good, so this test is dangerous as well as racy.
Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
In btrfs_wait_ordered_range we have been calling filemap_fdata_write() twice
because compression does strange things and then waiting. Then we look up
ordered extents and if we find any we will always schedule_timeout(); once
and then loop back around and do it all again. We will even check to see if
there is delalloc pages on this range and loop again. So this patch gets
rid of the multipe fdata_write() calls and just does
filemap_write_and_wait(). In the case of compression we will still find the
ordered extents and start those individually if we need to so that is ok,
but in the normal buffered case we avoid all this weird overhead.
Then in the case of the schedule_timeout(1), we don't need it. All callers
either 1) don't care, they just want to make sure what they just wrote maeks
it to disk or 2) are doing the lock()->lookup ordered->unlock->flush thing
in which case it will lock and check for ordered extents _anyway_ so get
back to them as quickly as possible. The delaloc check is simply not
needed, this only catches the case where we write to the file again since
doing the filemap_write_and_wait() and if the caller truly cares about that
it will take care of everything itself. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
The ordered data and relocation trees have BUG_ONs to protect against
bad tree operations.
This patch replaces them with a panic that will report the problem.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Tracepoints can provide insight into why btrfs hits bugs and be greatly
helpful for debugging, e.g
dd-7822 [000] 2121.641088: btrfs_inode_request: root = 5(FS_TREE), gen = 4, ino = 256, blocks = 8, disk_i_size = 0, last_trans = 8, logged_trans = 0
dd-7822 [000] 2121.641100: btrfs_inode_new: root = 5(FS_TREE), gen = 8, ino = 257, blocks = 0, disk_i_size = 0, last_trans = 0, logged_trans = 0
btrfs-transacti-7804 [001] 2146.935420: btrfs_cow_block: root = 2(EXTENT_TREE), refs = 2, orig_buf = 29368320 (orig_level = 0), cow_buf = 29388800 (cow_level = 0)
btrfs-transacti-7804 [001] 2146.935473: btrfs_cow_block: root = 1(ROOT_TREE), refs = 2, orig_buf = 29364224 (orig_level = 0), cow_buf = 29392896 (cow_level = 0)
btrfs-transacti-7804 [001] 2146.972221: btrfs_transaction_commit: root = 1(ROOT_TREE), gen = 8
flush-btrfs-2-7821 [001] 2155.824210: btrfs_chunk_alloc: root = 3(CHUNK_TREE), offset = 1103101952, size = 1073741824, num_stripes = 1, sub_stripes = 0, type = DATA
flush-btrfs-2-7821 [001] 2155.824241: btrfs_cow_block: root = 2(EXTENT_TREE), refs = 2, orig_buf = 29388800 (orig_level = 0), cow_buf = 29396992 (cow_level = 0)
flush-btrfs-2-7821 [001] 2155.824255: btrfs_cow_block: root = 4(DEV_TREE), refs = 2, orig_buf = 29372416 (orig_level = 0), cow_buf = 29401088 (cow_level = 0)
flush-btrfs-2-7821 [000] 2155.824329: btrfs_cow_block: root = 3(CHUNK_TREE), refs = 2, orig_buf = 20971520 (orig_level = 0), cow_buf = 20975616 (cow_level = 0)
btrfs-endio-wri-7800 [001] 2155.898019: btrfs_cow_block: root = 5(FS_TREE), refs = 2, orig_buf = 29384704 (orig_level = 0), cow_buf = 29405184 (cow_level = 0)
btrfs-endio-wri-7800 [001] 2155.898043: btrfs_cow_block: root = 7(CSUM_TREE), refs = 2, orig_buf = 29376512 (orig_level = 0), cow_buf = 29409280 (cow_level = 0)
Here is what I have added:
1) ordere_extent:
btrfs_ordered_extent_add
btrfs_ordered_extent_remove
btrfs_ordered_extent_start
btrfs_ordered_extent_put
These provide critical information to understand how ordered_extents are
updated.
2) extent_map:
btrfs_get_extent
extent_map is used in both read and write cases, and it is useful for tracking
how btrfs specific IO is running.
3) writepage:
__extent_writepage
btrfs_writepage_end_io_hook
Pages are cirtical resourses and produce a lot of corner cases during writeback,
so it is valuable to know how page is written to disk.
4) inode:
btrfs_inode_new
btrfs_inode_request
btrfs_inode_evict
These can show where and when a inode is created, when a inode is evicted.
5) sync:
btrfs_sync_file
btrfs_sync_fs
These show sync arguments.
6) transaction:
btrfs_transaction_commit
In transaction based filesystem, it will be useful to know the generation and
who does commit.
7) back reference and cow:
btrfs_delayed_tree_ref
btrfs_delayed_data_ref
btrfs_delayed_ref_head
btrfs_cow_block
Btrfs natively supports back references, these tracepoints are helpful on
understanding btrfs's COW mechanism.
8) chunk:
btrfs_chunk_alloc
btrfs_chunk_free
Chunk is a link between physical offset and logical offset, and stands for space
infomation in btrfs, and these are helpful on tracing space things.
9) reserved_extent:
btrfs_reserved_extent_alloc
btrfs_reserved_extent_free
These can show how btrfs uses its space.
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This one isn't really an uninit variable, but for pretty
obscure reasons. Let's make it clearly correct.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Make the code aware of compression type, instead of always assuming
zlib compression.
Also make the zlib workspace function as common code for all
compression types.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
The new DIO bio splitting code has problems when the bio
spans more than one ordered extent. This will happen as the
generic DIO code merges our get_blocks calls together into
a bigger single bio.
This fixes things by walking forward in the ordered extent
code finding all the overlapping ordered extents and completing them
all at once.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
These are all the cases where a variable is set, but not read which are
not bugs as far as I can see, but simply leftovers.
Still needs more review.
Found by gcc 4.6's new warnings
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This provides basic DIO support for reading and writing. It does not do the
work to recover from mismatching checksums, that will come later. A few design
changes have been made from Jim's code (sorry Jim!)
1) Use the generic direct-io code. Jim originally re-wrote all the generic DIO
code in order to account for all of BTRFS's oddities, but thanks to that work it
seems like the best bet is to just ignore compression and such and just opt to
fallback on buffered IO.
2) Fallback on buffered IO for compressed or inline extents. Jim's code did
it's own buffering to make dio with compressed extents work. Now we just
fallback onto normal buffered IO.
3) Use ordered extents for the writes so that all of the
lock_extent()
lookup_ordered()
type checks continue to work.
4) Do the lock_extent() lookup_ordered() loop in readpage so we don't race with
DIO writes.
I've tested this with fsx and everything works great. This patch depends on my
dio and filemap.c patches to work. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Introduce metadata reservation context for delayed allocation
and update various related functions.
This patch also introduces EXTENT_FIRST_DELALLOC control bit for
set/clear_extent_bit. It tells set/clear_bit_hook whether they
are processing the first extent_state with EXTENT_DELALLOC bit
set. This change is important if set/clear_extent_bit involves
multiple extent_state.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: add check for changed leaves in setup_leaf_for_split
Btrfs: create snapshot references in same commit as snapshot
Btrfs: fix small race with delalloc flushing waitqueue's
Btrfs: use add_to_page_cache_lru, use __page_cache_alloc
Btrfs: fix chunk allocate size calculation
Btrfs: kill max_extent mount option
Btrfs: fail to mount if we have problems reading the block groups
Btrfs: check btrfs_get_extent return for IS_ERR()
Btrfs: handle kmalloc() failure in inode lookup ioctl
Btrfs: dereferencing freed memory
Btrfs: Simplify num_stripes's calculation logical for __btrfs_alloc_chunk()
Btrfs: Add error handle for btrfs_search_slot() in btrfs_read_chunk_tree()
Btrfs: Remove unnecessary finish_wait() in wait_current_trans()
Btrfs: add NULL check for do_walk_down()
Btrfs: remove duplicate include in ioctl.c
Fix trivial conflict in fs/btrfs/compression.c due to slab.h include
cleanups.
As Yan pointed out, theres not much reason for all this complicated math to
account for file extents being split up into max_extent chunks, since they are
likely to all end up in the same leaf anyway. Since there isn't much reason to
use max_extent, just remove the option altogether so we have one less thing we
need to test.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
When finishing io we run btrfs_dec_test_ordered_pending, and then immediately
run btrfs_lookup_ordered_extent, but btrfs_dec_test_ordered_pending does that
already, so we're searching twice when we don't have to. This patch lets us
pass a btrfs_ordered_extent in to btrfs_dec_test_ordered_pending so if we do
complete io on that ordered extent we can just use the one we found then instead
of having to do another btrfs_lookup_ordered_extent. This made my fio job with
the other patch go from 24 mb/s to 29 mb/s.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The ordered tree used to need a mutex, but currently all we use it for is to
protect the rb_tree, and a spin_lock is just fine for that. Using a spin_lock
instead makes dbench run a little faster, 58 mb/s instead of 51 mb/s, and have
less latency, 3445.138 ms instead of 3820.633 ms.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Some callers of btrfs_ordered_update_i_size can now pass in
a NULL for the ordered extent to update against. This makes
sure we properly align the offset they pass in when deciding
how much to bump the on disk i_size.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
iput() can trigger new transactions if we are dropping the
final reference, so calling it in btrfs_commit_transaction
may end up deadlock. This patch adds delayed iput to avoid
the issue.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
There are some cases file extents are inserted without involving
ordered struct. In these cases, we update disk_i_size directly,
without checking pending ordered extent and DELALLOC bit. This
patch extends btrfs_ordered_update_i_size() to handle these cases.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix file clone ioctl for bookend extents
Btrfs: fix uninit compiler warning in cow_file_range_nocow
Btrfs: constify dentry_operations
Btrfs: optimize back reference update during btrfs_drop_snapshot
Btrfs: remove negative dentry when deleting subvolumne
Btrfs: optimize fsync for the single writer case
Btrfs: async delalloc flushing under space pressure
Btrfs: release delalloc reservations on extent item insertion
Btrfs: delay clearing EXTENT_DELALLOC for compressed extents
Btrfs: cleanup extent_clear_unlock_delalloc flags
Btrfs: fix possible softlockup in the allocator
Btrfs: fix deadlock on async thread startup
This patch fixes an issue with the delalloc metadata space reservation
code. The problem is we used to free the reservation as soon as we
allocated the delalloc region. The problem with this is if we are not
inserting an inline extent, we don't actually insert the extent item until
after the ordered extent is written out. This patch does 3 things,
1) It moves the reservation clearing stuff into the ordered code, so when
we remove the ordered extent we remove the reservation.
2) It adds a EXTENT_DO_ACCOUNTING flag that gets passed when we clear
delalloc bits in the cases where we want to clear the metadata reservation
when we clear the delalloc extent, in the case that we do an inline extent
or we invalidate the page.
3) It adds another waitqueue to the space info so that when we start a fs
wide delalloc flush, anybody else who also hits that area will simply wait
for the flush to finish and then try to make their allocation.
This has been tested thoroughly to make sure we did not regress on
performance.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Use filemap_fdatawrite_range and filemap_fdatawait_range instead of
local copies of the functions. For filemap_fdatawait_range that
also means replacing the awkward old wait_on_page_writeback_range
calling convention with the regular filemap byte offsets.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Btrfs writes go through delalloc to the data=ordered code. This
makes sure that all of the data is on disk before the metadata
that references it. The tracking means that we have to make sure
each page in an extent is fully written before we add that extent into
the on-disk btree.
This was done in the past by setting the EXTENT_ORDERED bit for the
range of an extent when it was added to the data=ordered code, and then
clearing the EXTENT_ORDERED bit in the extent state tree as each page
finished IO.
One of the reasons we had to do this was because sometimes pages are
magically dirtied without page_mkwrite being called. The EXTENT_ORDERED
bit is checked at writepage time, and if it isn't there, our page become
dirty without going through the proper path.
These bit operations make for a number of rbtree searches for each page,
and can cause considerable lock contention.
This commit switches from the EXTENT_ORDERED bit to use PagePrivate2.
As pages go into the ordered code, PagePrivate2 is set on each one.
This is a cheap operation because we already have all the pages locked
and ready to go.
As IO finishes, the PagePrivate2 bit is cleared and the ordered
accoutning is updated for each page.
At writepage time, if the PagePrivate2 bit is missing, we go into the
writepage fixup code to handle improperly dirtied pages.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This changes the btrfs code to find delalloc ranges in the extent state
tree to use the new state caching code from set/test bit. It reduces
one of the biggest causes of rbtree searches in the writeback path.
test_range_bit is also modified to take the cached state as a starting
point while searching.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Part of reducing fsync/O_SYNC/O_DIRECT latencies is using WRITE_SYNC for
writes we plan on waiting on in the near future. This patch
mirrors recent changes in other filesystems and the generic code to
use WRITE_SYNC when WB_SYNC_ALL is passed and to use WRITE_SYNC for
other latency critical writes.
Btrfs uses async worker threads for checksumming before the write is done,
and then again to actually submit the bios. The bio submission code just
runs a per-device list of bios that need to be sent down the pipe.
This list is split into low priority and high priority lists so the
WRITE_SYNC IO happens first.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Renames and truncates are both common ways to replace old data with new
data. The filesystem can make an effort to make sure the new data is
on disk before actually replacing the old data.
This is especially important for rename, which many application use as
though it were atomic for both the data and the metadata involved. The
current btrfs code will happily replace a file that is fully on disk
with one that was just created and still has pending IO.
If we crash after transaction commit but before the IO is done, we'll end
up replacing a good file with a zero length file. The solution used
here is to create a list of inodes that need special ordering and force
them to disk before the commit is done. This is similar to the
ext3 style data=ordering, except it is only done on selected files.
Btrfs is able to get away with this because it does not wait on commits
very often, even for fsync (which use a sub-commit).
For renames, we order the file when it wasn't already
on disk and when it is replacing an existing file. Larger files
are sent to filemap_flush right away (before the transaction handle is
opened).
For truncates, we order if the file goes from non-zero size down to
zero size. This is a little different, because at the time of the
truncate the file has no dirty bytes to order. But, we flag the inode
so that it is added to the ordered list on close (via release method). We
also immediately add it to the ordered list of the current transaction
so that we can try to flush down any writes the application sneaks in
before commit.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef Bacik
Geert Uytterhoeven
Miao Xie
Liu Bo
Artem Bityutskiy
Josef Bacik
Jeff Mahoney
liubo
Chris Mason
Li Zefan
Andi Kleen
Yan, Zheng
Linus Torvalds
Tejun Heo
Yan, Zheng
Christoph Hellwig
Jens Axboe