This patchset enables the ethtool layer to program n-tuple
filters to an underlying device. The idea is to allow capable
hardware to have static rules applied that can assist steering
flows into appropriate queues.
Hardware that is known to support these types of filters today
are ixgbe and niu.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the vlan and macvlan drivers, the start_xmit function forwards
data to the dev_queue_xmit function for another device, which may
potentially belong to a different namespace.
To make sure that classification stays within a single namespace,
this resets the potentially critical fields.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces three macros to work with uc list from net drivers.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid checking twice whether skb needs to be linearized, if one
skb_linearize was already done.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The contents of /proc/net/dev is annoying to parse, because
it changes whether there is a space after the "ethX:" or not.
It depends upon the size of the "Receive bytes" counter,
if the number is below 7 digits, then there is whitespaces
else if the number is 8 digits or above there is no space
between the ":" and the number.
This patch changes the output to assure there is always a space
between the ":" and the number. Given that all existing userspace
application already need to handle the whitespaces, I see
no breakage of existing tools.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Wed, Jan 06, 2010 at 10:10:03PM +0100, Eric Dumazet wrote:
> Le 06/01/2010 19:38, Eric Dumazet a écrit :
> >
> > (net-next-2.6 doesnt work well on my bond/vlan setup, I suspect I need a bisection)
>
> David, I had to revert 1f3c8804ac
> (bonding: allow arp_ip_targets on separate vlans to use arp validation)
>
> Or else, my vlan devices dont work (unfortunatly I dont have much time
> these days to debug the thing)
>
> My config :
>
> +---------+
> vlan.103 -----+ bond0 +--- eth1 (bnx2)
> | +
> vlan.825 -----+ +--- eth2 (tg3)
> +---------+
>
> $ cat /proc/net/bonding/bond0
> Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
>
> Bonding Mode: fault-tolerance (active-backup)
> Primary Slave: None
> Currently Active Slave: eth2
> MII Status: up
> MII Polling Interval (ms): 100
> Up Delay (ms): 0
> Down Delay (ms): 0
>
> Slave Interface: eth1 (bnx2)
> MII Status: down
> Link Failure Count: 1
> Permanent HW addr: 00:1e:0b:ec:d3:d2
>
> Slave Interface: eth2 (tg3)
> MII Status: up
> Link Failure Count: 0
> Permanent HW addr: 00:1e:0b:92:78:50
>
This patch fixes up a problem with found with commit
1f3c8804ac. The original change
overloaded null_or_orig, but doing that prevented any packet handlers
that were not tied to a specific device (i.e. ptype->dev == NULL) from
ever receiving any frames.
The null_or_orig variable cannot be overloaded, and must be kept as NULL
to prevent the frame from being ignored by packet handlers designed to
accept frames on any interface.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows a bond device to specify an arp_ip_target as a host that is
not on the same vlan as the base bond device and still use arp
validation. A configuration like this, now works:
BONDING_OPTS="mode=active-backup arp_interval=1000 arp_ip_target=10.0.100.1 arp_validate=3"
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
8: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
inet6 fe80::213:21ff:febe:33e9/64 scope link
valid_lft forever preferred_lft forever
9: bond0.100@bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
inet 10.0.100.2/24 brd 10.0.100.255 scope global bond0.100
inet6 fe80::213:21ff:febe:33e9/64 scope link
valid_lft forever preferred_lft forever
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth1
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
ARP Polling Interval (ms): 1000
ARP IP target/s (n.n.n.n form): 10.0.100.1
Slave Interface: eth1
MII Status: up
Link Failure Count: 1
Permanent HW addr: 00:40:05:30:ff:30
Slave Interface: eth0
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:13:21:be:33:e9
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Non-GSO code drops dst entry for performance reasons, but
the same is missing for GSO code. Drop dst while cache-hot
for GSO case too.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I received some bug reports about userspace programs having problems
because after RTM_NEWLINK was received they could not immediate access
files under /proc/sys/net/ because they had not been registered yet.
The original problem was trivially fixed by moving the userspace
notification from rtnetlink_event() to the end of
register_netdevice().
When testing that change I discovered I was still getting RTM_NEWLINK
events before I could access proc and I was also getting RTM_NEWLINK
events after I was seeing RTM_DELLINK. Things practically guaranteed
to confuse userspace.
After a little more investigation these extra notifications proved to
be from the new notifiers NETDEV_POST_INIT and NETDEV_UNREGISTER_BATCH
hitting the default case in rtnetlink_event, and triggering
unnecessary RTM_NEWLINK messages.
rtnetlink_event now explicitly handles NETDEV_UNREGISTER_BATCH and
NETDEV_POST_INIT to avoid sending the incorrect userspace
notifications.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two problems:
1. If unregister_netdevice_many() is called with both registered
and unregistered devices, rollback_registered_many() bails out
when it reaches the first unregistered device. The processing
of the prior registered devices is unfinished, and the
remaining devices are skipped, and possible registered netdev's
are leaked/unregistered.
2. System hangs or panics depending on how the devices are passed,
since when netdev_run_todo() runs, some devices were not fully
processed.
Tested by passing intermingled unregistered and registered vlan
devices to unregister_netdevice_many() as follows:
1. dev, fake_dev1, fake_dev2: hangs in run_todo
("unregister_netdevice: waiting for eth1.100 to become
free. Usage count = 1")
2. fake_dev1, dev, fake_dev2: failure during de-registration
and next registration, followed by a vlan driver Oops
during subsequent registration.
Confirmed that the patch fixes both cases.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide common routine for the transition of operational state for a leaf
device during a root device transition.
Signed-off-by: Patrick Mullaney <pmullaney@novell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move network device exit batching from a special case in
net_namespace.c to using common mechanisms in dev.c
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Defer dellink to net_cleanup() allowing for batching.
- Fix comment.
- Use for_each_netdev_safe again as dev_change_net_namespace touches
at most one network device (unlike veth dellink).
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The motivation for an additional notifier in batched netdevice
notification (rt_do_flush) only needs to be called once per batch not
once per namespace.
For further batching improvements I need a guarantee that the
netdevices are unregistered in order allowing me to unregister an all
of the network devices in a network namespace at the same time with
the guarantee that the loopback device is really and truly
unregistered last.
Additionally it appears that we moved the route cache flush after
the final synchronize_net, which seems wrong and there was no
explanation. So I have restored the original location of the final
synchronize_net.
Cc: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not including net/atm/
Compiled tested x86 allyesconfig only
Added a > 80 column line or two, which I ignored.
Existing checkpatch plaints willfully, cheerfully ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The veth driver contains code to forward an skb
from the start_xmit function of one network
device into the receive path of another device.
Moving that code into a common location lets us
reuse the code for direct forwarding of data
between macvlan ports, and possibly in other
drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generated with the following semantic patch
@@
struct net *n1;
struct net *n2;
@@
- n1 == n2
+ net_eq(n1, n2)
@@
struct net *n1;
struct net *n2;
@@
- n1 != n2
+ !net_eq(n1, n2)
applied over {include,net,drivers/net}.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following htmldocs warning:
Warning(net/core/dev.c:5378): bad line:
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu a écrit :
> On Tue, Nov 17, 2009 at 04:26:04AM -0800, David Miller wrote:
>> Really, the link watch stuff is just due for a redesign. I don't
>> think a simple hack is going to cut it this time, sorry Eric :-)
>
> I have no objections against any redesigns, but since the only
> caller of linkwatch_forget_dev runs in process context with the
> RTNL, it could also legally emit those events.
Thanks guys, here an updated version then, before linkwatch surgery ?
In this version, I force the event to be sent synchronously.
[PATCH net-next-2.6] linkwatch: linkwatch_forget_dev() to speedup device dismantle
time ip link del eth3.103 ; time ip link del eth3.104 ; time ip link del eth3.105
real 0m0.266s
user 0m0.000s
sys 0m0.001s
real 0m0.770s
user 0m0.000s
sys 0m0.000s
real 0m1.022s
user 0m0.000s
sys 0m0.000s
One problem of current schem in vlan dismantle phase is the
holding of device done by following chain :
vlan_dev_stop() ->
netif_carrier_off(dev) ->
linkwatch_fire_event(dev) ->
dev_hold() ...
And __linkwatch_run_queue() runs up to one second later...
A generic fix to this problem is to add a linkwatch_forget_dev() method
to unlink the device from the list of watched devices.
dev->link_watch_next becomes dev->link_watch_list (and use a bit more memory),
to be able to unlink device in O(1).
After patch :
time ip link del eth3.103 ; time ip link del eth3.104 ; time ip link del eth3.105
real 0m0.024s
user 0m0.000s
sys 0m0.000s
real 0m0.032s
user 0m0.000s
sys 0m0.001s
real 0m0.033s
user 0m0.000s
sys 0m0.000s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new event is called once for each unique net namespace in batched
unregister operations (with the argument set to a random device from
that namespace) and once per device in non-batched unregister
operations.
It allows us to factorize some device unregister work such as clearing the
routing cache.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers ndo_get_stats() method need to perform txqueue stats folding.
Move folding from dev_get_stats() to a new dev_txq_stats_fold() function
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: Fix the rollback test in dev_change_name()
In dev_change_name() an err variable is used for storing the original
call_netdevice_notifiers() errno (negative) and testing for a rollback
error later, but the test for non-zero is wrong, because the err might
have positive value as well - from dev_alloc_name(). It means the
rollback for a netdevice with a number > 0 will never happen. (The err
test is reordered btw. to make it more readable.)
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes in the TX error propagation require additional checking
and masking of values returned from hard_start_xmit(), mainly to
separate cases where skb was consumed. This aim can be simplified by
changing the order of NETDEV_TX and NET_XMIT codes, because the latter
are treated similarly to negative (ERRNO) values.
After this change much simpler dev_xmit_complete() is also used in
sch_direct_xmit(), so it is moved to netdevice.h.
Additionally NET_RX definitions in netdevice.h are moved up from
between TX codes to avoid confusion while reading the TX comment.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the return value of ndo_select_queue(). If the value isn't smaller
than the real_num_tx_queues, print a warning message, and reset it to zero.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
----
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ->ndo_hard_start_xmit() callbacks are only permitted to return
one of the NETDEV_TX codes. This prevents any kind of error propagation for
virtual devices, like queue congestion of the underlying device in case of
layered devices, or unreachability in case of tunnels.
This patches changes the NET_XMIT codes to avoid clashes with the NETDEV_TX
codes and changes the two callers of dev_hard_start_xmit() to expect either
errno codes, NET_XMIT codes or NETDEV_TX codes as return value.
In case of qdisc_restart(), all non NETDEV_TX codes are mapped to NETDEV_TX_OK
since no error propagation is possible when using qdiscs. In case of
dev_queue_xmit(), the error is propagated upwards.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The full_name_hash function does not produce well distributed values in
the lower bits, so most code uses hash_32() to fold it. This is really
a bug introduced when name hashing was added, back in 2.5 when I added
name hashing.
hash_32 is all that is needed since full_name_hash returns unsigned int
which is only 32 bits on 64 bit platforms.
Also, there is no point in using hash_32 on ifindex, because the is naturally
sequential and usually well distributed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds RCU management to the list of netdevices.
Convert some for_each_netdev() users to RCU version, if
it can avoid read_lock-ing dev_base_lock
Ie:
read_lock(&dev_base_loack);
for_each_netdev(net, dev)
some_action();
read_unlock(&dev_base_lock);
becomes :
rcu_read_lock();
for_each_netdev_rcu(net, dev)
some_action();
rcu_read_unlock();
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All ioctls() implemented by dev_ifsioc_locked() :
SIOCGIFFLAGS, SIOCGIFMETRIC, SIOCGIFMTU, SIOCGIFHWADDR,
SIOCGIFSLAVE, SIOCGIFMAP, SIOCGIFINDEX & SIOCGIFTXQLEN
can use RCU lock instead of dev_base_lock rwlock
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I tested the recent unregister many changes and got a weird,
nasty and seemingly unrelasted kernel oops. Changing
unregister_netdevice_queue to use list_move_tail fixes
the problem for me.
ip link add type veth
rmmod veth
ls /sys/class/net/
showed one of the veth devices still present.
A subsequent ip link oopsed the box.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some workloads hit dev_base_lock rwlock pretty hard.
We can use RCU lookups to avoid touching this rwlock
(and avoid touching netdevice refcount)
netdevices are already freed after a RCU grace period, so this patch
adds no penalty at device dismantle time.
However, it adds a synchronize_rcu() call in dev_change_name()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Small cleanup of __dev_get_by_name() and __dev_get_by_index()
to use hlist_for_each_entry() : They'll look like their _rcu variant.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow drivers to adjust their receive path dynamically
based on whether GRO is being applied successfully.
Currently all in-tree callers ignore the return values of these
functions and do not need to be changed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This clarifies which return and parameter types are GRO result codes
and not RX result codes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some workloads hit dev_base_lock rwlock pretty hard.
We can use RCU lookups to avoid touching this rwlock.
netdevices are already freed after a RCU grace period, so this patch
adds no penalty at device dismantle time.
dev_ifname() converted to dev_get_by_index_rcu()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use unregister_netdevice_many() to speedup master device unregister.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a list_head parameter to rtnl_link_ops->dellink() methods
allow us to queue devices on a list, in order to dismantle
them all at once.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce rollback_registered_many() and unregister_netdevice_many()
rollback_registered_many() is able to perform necessary steps at device dismantle
time, factorizing two expensive synchronize_net() calls.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchs adds an unreg_list anchor to struct net_device, and
introduces an unregister_netdevice_queue() function, able to queue
a net_device to a list instead of immediately unregister it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently use a 16 bit field (vlan_tci) to store VLAN ID/PRIO on a skb.
Null value is used as a special value, meaning vlan tagging not enabled.
This forbids use of null vlan ID.
As pointed by David, some drivers use the 3 high order bits (PRIO)
As VLAN ID is 12 bits, we can use the remaining bit (CFI) as a flag, and
allow null VLAN ID.
In case future code really wants to use VLAN_CFI_MASK, we'll have to use
a bit outside of vlan_tci.
#define VLAN_PRIO_MASK 0xe000 /* Priority Code Point */
#define VLAN_PRIO_SHIFT 13
#define VLAN_CFI_MASK 0x1000 /* Canonical Format Indicator */
#define VLAN_TAG_PRESENT VLAN_CFI_MASK
#define VLAN_VID_MASK 0x0fff /* VLAN Identifier */
Reported-by: Gertjan Hofman <gertjan_hofman@yahoo.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling large number of netdevice, rtnl_dump_ifinfo()
is very slow because it has O(N^2) complexity.
Instead of scanning one single list, we can use the 256 sub lists
of the dev_index hash table.
This considerably speedups "ip link" operations
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For connected sockets, the first run of dev_pick_tx saves the
calculated txq in sk_tx_queue_mapping. This is not saved if
either the device has a queue select or the socket is not
connected. Next iterations of dev_pick_tx uses the cached value
of sk_tx_queue_mapping.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that software UFO is supported, UFO can be enabled on master
devices like bridge, bond even though the attached device doesn't
support this feature in hardware.
This allows UFO to be used between KVM host and guest even when a
physical interface attached to the bridge doesn't support UFO.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
For various purposes including a wireless extensions
bugfix, we need to hook into the netdev creation before
before netdev_register_kobject(). This will also ease
doing the dev type assignment that Marcel was working
on for cfg80211 drivers w/o touching them all.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 9b22ea5609
( net: fix packet socket delivery in rx irq handler )
We lost rx timestamping of packets received on accelerated vlans.
Effect is that tcpdump on real dev can show strange timings, since it gets rx timestamps
too late (ie at skb dequeueing time, not at skb queueing time)
14:47:26.986871 IP 192.168.20.110 > 192.168.20.141: icmp 64: echo request seq 1
14:47:26.986786 IP 192.168.20.141 > 192.168.20.110: icmp 64: echo reply seq 1
14:47:27.986888 IP 192.168.20.110 > 192.168.20.141: icmp 64: echo request seq 2
14:47:27.986781 IP 192.168.20.141 > 192.168.20.110: icmp 64: echo reply seq 2
14:47:28.986896 IP 192.168.20.110 > 192.168.20.141: icmp 64: echo request seq 3
14:47:28.986780 IP 192.168.20.141 > 192.168.20.110: icmp 64: echo reply seq 3
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes commit e36b9d16c6. The approach
there is to call dev_close()/dev_open() whenever the device type is changed in
order to remap the device IP multicast addresses to HW multicast addresses.
This approach suffers from 2 drawbacks:
*. It assumes tha the device is UP when calling dev_close(), or otherwise
dev_close() has no affect. It is worth to mention that initscripts (Redhat)
and sysconfig (Suse) doesn't act the same in this matter.
*. dev_close() has other side affects, like deleting entries from the routing
table, which might be unnecessary.
The fix here is to directly remap the IP multicast addresses to HW multicast
addresses for a bonding device that changes its type, and nothing else.
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
The only valid usage for the bridge frame hooks are by a
GPL components (such as the bridge module).
The kernel should not leave a crack in the door for proprietary
networking stacks to slip in.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a debugging aid I accidently left in previous 'cleanup' patch
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch compiled and 32 simultaneous netperf testing ran fine.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are not maste devices in mac802154 anymore, so drop
ARPHRD_IEEE802154_PHY definition.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
The networking code checks CAP_SYS_MODULE before using request_module() to
try to load a kernel module. While this seems reasonable it's actually
weakening system security since we have to allow CAP_SYS_MODULE for things
like /sbin/ip and bluetoothd which need to be able to trigger module loads.
CAP_SYS_MODULE actually grants those binaries the ability to directly load
any code into the kernel. We should instead be protecting modprobe and the
modules on disk, rather than granting random programs the ability to load code
directly into the kernel. Instead we are going to gate those networking checks
on CAP_NET_ADMIN which still limits them to root but which does not grant
those processes the ability to load arbitrary code into the kernel.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Paul Moore <paul.moore@hp.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Morris <jmorris@namei.org>
dev_queue_xmit enqueue's a skb and calls qdisc_run which
dequeue's the skb and xmits it. In most cases, the skb that
is enqueue'd is the same one that is dequeue'd (unless the
queue gets stopped or multiple cpu's write to the same queue
and ends in a race with qdisc_run). For default qdiscs, we
can remove the redundant enqueue/dequeue and simply xmit the
skb since the default qdisc is work-conserving.
The patch uses a new flag - TCQ_F_CAN_BYPASS to identify the
default fast queue. The controversial part of the patch is
incrementing qlen when a skb is requeued - this is to avoid
checks like the second line below:
+ } else if ((q->flags & TCQ_F_CAN_BYPASS) && !qdisc_qlen(q) &&
>> !q->gso_skb &&
+ !test_and_set_bit(__QDISC_STATE_RUNNING, &q->state)) {
Results of a 2 hour testing for multiple netperf sessions (1,
2, 4, 8, 12 sessions on a 4 cpu system-X). The BW numbers are
aggregate Mb/s across iterations tested with this version on
System-X boxes with Chelsio 10gbps cards:
----------------------------------
Size | ORG BW NEW BW |
----------------------------------
128K | 156964 159381 |
256K | 158650 162042 |
----------------------------------
Changes from ver1:
1. Move sch_direct_xmit declaration from sch_generic.h to
pkt_sched.h
2. Update qdisc basic statistics for direct xmit path.
3. Set qlen to zero in qdisc_reset.
4. Changed some function names to more meaningful ones.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
String literals are constant, and usually, we can also tag the array
of pointers const too, moving it to the .rodata section.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a path when an assetion in dev_unicast_sync() appears.
igmp6_group_added -> dev_mc_add -> __dev_set_rx_mode ->
-> vlan_dev_set_rx_mode -> dev_unicast_sync
Therefore we cannot protect this list with rtnl. This patch restores the
original protecting this list with spinlock.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make cfg80211/nl80211 aware of network namespaces,
we have to do the following things:
* del_virtual_intf method takes an interface index rather
than a netdev pointer - simply change this
* nl80211 uses init_net a lot, it changes to use the sender's
network namespace
* scan requests use the interface index, hold a netdev pointer
and reference instead
* we want a wiphy and its associated virtual interfaces to be
in one netns together, so
- we need to be able to change ns for a given interface, so
export dev_change_net_namespace()
- for each virtual interface set the NETIF_F_NETNS_LOCAL
flag, and clear that flag only when the wiphy changes ns,
to disallow breaking this invariant
* when a network namespace goes away, we need to reparent the
wiphy to init_net
* cfg80211 users that support creating virtual interfaces must
create them in the wiphy's namespace, currently this affects
only mac80211
The end result is that you can now switch an entire wiphy into
a different network namespace with the new command
iw phy#<idx> set netns <pid>
and all virtual interfaces will follow (or the operation fails).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For mac80211, with the master netdev removal, we need to be
able to sync a multicast address list onto another list that
is not tracked within a netdev, so we need access to the
functions doing that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts the remaining occurences of raw return values to their
symbolic counterparts in ndo_start_xmit() functions that were missed by the
previous automatic conversion.
Additionally code that assumed the symbolic value of NETDEV_TX_OK to be zero
is changed to explicitly use NETDEV_TX_OK.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NAPI is disabled while we're in net_rx_action, we end up
calling __napi_complete without flushing GRO packets. This is
a bug as it would cause the GRO packets to linger, of course it
also literally BUGs to catch error like this :)
This patch changes it to napi_complete, with the obligatory IRQ
reenabling. This should be safe because we've only just disabled
IRQs and it does not materially affect the test conditions in
between.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to get the tun driver to account packets, we need to be
able to receive packets with destructors set. To be on the safe
side, I added an skb_orphan call for all protocols by default since
some of them (IP in particular) cannot handle receiving packets
destructors properly.
Now it seems that at least one protocol (CAN) expects to be able
to pass skb->sk through the rx path without getting clobbered.
So this patch attempts to fix this properly by moving the skb_orphan
call to where it's actually needed. In particular, I've added it
to skb_set_owner_[rw] which is what most users of skb->destructor
call.
This is actually an improvement for tun too since it means that
we only give back the amount charged to the socket when the skb
is passed to another socket that will also be charged accordingly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Oliver Hartkopp <olver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is inspired by patch recently posted by Johannes Berg. Basically what
my patch does is to group list and a count of addresses into newly introduced
structure netdev_hw_addr_list. This brings us two benefits:
1) struct net_device becames a bit nicer.
2) in the future there will be a possibility to operate with lists independently
on netdevices (with exporting right functions).
I wanted to introduce this patch before I'll post a multicast lists conversion.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 4 +-
drivers/net/e1000/e1000_main.c | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/mv643xx_eth.c | 2 +-
drivers/net/niu.c | 4 +-
drivers/net/virtio_net.c | 10 ++--
drivers/s390/net/qeth_l2_main.c | 2 +-
include/linux/netdevice.h | 17 +++--
net/core/dev.c | 130 ++++++++++++++++++--------------------
9 files changed, 89 insertions(+), 90 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes FDB entry check for ATM LANE bridge integration.
There's no point in holding a FDB entry around SKB building.
br_fdb_get()/br_fdb_put() pair are changed into single br_fdb_test_addr()
hook that checks if the addr has FDB entry pointing to other port
to the one the request arrived on.
FDB entry refcounting is removed as it's not used anywhere else.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b00055aacd " [NET] core: add
RFC2863 operstate" defined new interface flag values. Its
documentation specified that these flags could be accessed from user
space via SIOCGIFFLAGS. However, this does not work because the new
flags do not fit in that ioctl's argument width.
Change the documentation to match the code's behavior. Also change
the source to explicitly show the truncation. This _should_ have no
effect on executable code, and did not with gcc 4.2.4 generating x86
code.
A new ioctl could be defined to return all interface flags to user
space. However, since this has been broken for three years with no
one complaining, there doesn't seem much need. They are still
accessible via netlink.
Reported-by: "Fredrik Arnerup" <fredrik.arnerup@edgeware.tv>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.15.4 stack requires several constants to be defined/adjusted.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit f001fde5ea
(net: introduce a list of device addresses dev_addr_list (v6))
added one regression Vegard Nossum found in its testings.
With kmemcheck help, Vegard found some uninitialized memory
was read and reported to user, potentialy leaking kernel data.
( thread can be found on http://lkml.org/lkml/2009/5/30/177 )
dev_addr_init() incorrectly uses sizeof() operator. We were
initializing one byte instead of MAX_ADDR_LEN bytes.
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETDEV_UP is called after the device is set UP, but sometimes
it is useful to be able to veto the device UP. Introduce a
new NETDEV_PRE_UP notifier that can be used for exactly this.
The first use case will be cfg80211 denying interfaces to be
set UP if the device is known to be rfkill'ed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).
I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.
The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 13 +--
drivers/net/e1000/e1000_main.c | 24 +++--
drivers/net/ixgbe/ixgbe_common.c | 14 ++--
drivers/net/ixgbe/ixgbe_common.h | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/ixgbe/ixgbe_type.h | 4 +-
drivers/net/macvlan.c | 11 +-
drivers/net/mv643xx_eth.c | 11 +-
drivers/net/niu.c | 7 +-
drivers/net/virtio_net.c | 7 +-
drivers/s390/net/qeth_l2_main.c | 6 +-
drivers/scsi/fcoe/fcoe.c | 16 ++--
include/linux/netdevice.h | 18 ++--
net/8021q/vlan.c | 4 +-
net/8021q/vlan_dev.c | 10 +-
net/core/dev.c | 195 +++++++++++++++++++++++++++-----------
net/dsa/slave.c | 10 +-
net/packet/af_packet.c | 4 +-
18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ALIGN() and PTR_ALIGN() macros instead of handcoding them.
Get rid of NETDEV_ALIGN_CONST ugly define
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we know the only packets which need the final pskb_may_pull
are completely non-linear, and have all the required bits in
frag0, we can perform a straight memcpy instead of going through
pskb_may_pull and doing skb_copy_bits.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the overwhelming majority of cases, skb_gro_header's return
value cannot be NULL. Yet we must check it because of its current
form. This patch splits it up into multiple functions in order
to avoid this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
By caching frag0_len, we can avoid checking both frag0 and the
length separately in skb_gro_header. This helps as skb_gro_header
is called four times per packet which amounts to a few million
times at 10Gb/s.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently skb_gro_header is used for packets which put the hardware
header in skb->data with the rest in frags. Since the drivers that
need this optimisation all provide completely non-linear packets,
we can gain extra optimisations by only performing the frag0
optimisation for completely non-linear packets.
In particular, we can simply test frag0 (instead of skb_headlen)
to see whether the optimisation is in force.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function skb_gro_header is called four times per packet which
quickly adds up at 10Gb/s. This patch inlines it to allow better
optimisations.
Some architectures perform multiplication for page_address, which
is done by each skb_gro_header invocation. This patch caches that
value in skb->cb to avoid the unnecessary multiplications.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We would like to get rid of netdev->trans_start = jiffies; that about all net
drivers have to use in their start_xmit() function, and use txq->trans_start
instead.
This can be done generically in core network, as suggested by David.
Some devices, (particularly loopback) dont need trans_start update, because
they dont have transmit watchdog. We could add a new device flag, or rely
on fact that txq->tran_start can be updated is txq->xmit_lock_owner is
different than -1. Use a helper function to hide our choice.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers are already converted to new net_device_ops API
and nobody uses old API anymore.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch to add the ability to detect drops in hardware interfaces via dropwatch.
Adds a tracepoint to net_rx_action to signal everytime a napi instance is
polled. The dropmon code then periodically checks to see if the rx_frames
counter has changed, and if so, adds a drop notification to the netlink
protocol, using the reserved all-0's vector to indicate the drop location was in
hardware, rather than somewhere in the code.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
include/linux/net_dropmon.h | 8 ++
include/trace/napi.h | 11 +++
net/core/dev.c | 5 +
net/core/drop_monitor.c | 124 ++++++++++++++++++++++++++++++++++++++++++--
net/core/net-traces.c | 4 +
net/core/netpoll.c | 2
6 files changed, 149 insertions(+), 5 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
One point of contention in high network loads is the dst_release() performed
when a transmited skb is freed. This is because NIC tx completion calls
dev_kree_skb() long after original call to dev_queue_xmit(skb).
CPU cache is cold and the atomic op in dst_release() stalls. On SMP, this is
quite visible if one CPU is 100% handling softirqs for a network device,
since dst_clone() is done by other cpus, involving cache line ping pongs.
It seems right place to release dst is in dev_hard_start_xmit(), for most
devices but ones that are virtual, and some exceptions.
David Miller suggested to define a new device flag, set in alloc_netdev_mq()
(so that most devices set it at init time), and carefuly unset in devices
which dont want a NULL skb->dst in their ndo_start_xmit().
List of devices that must clear this flag is :
- loopback device, because it calls netif_rx() and quoting Patrick :
"ip_route_input() doesn't accept loopback addresses, so loopback packets
already need to have a dst_entry attached."
- appletalk/ipddp.c : needs skb->dst in its xmit function
- And all devices that call again dev_queue_xmit() from their xmit function
(as some classifiers need skb->dst) : bonding, vlan, macvlan, eql, ifb, hdlc_fr
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
offsetof(struct net_device, features)=0x44
offsetof(struct net_device, stats.tx_packets)=0x54
offsetof(struct net_device, stats.tx_bytes)=0x5c
offsetof(struct net_device, stats.tx_dropped)=0x6c
Network drivers that touch dev->stats.tx_packets/stats.tx_bytes in their
tx path can slow down SMP operations, since they dirty a cache line
that should stay shared (dev->features is needed in rx and tx paths)
We could move away stats field in net_device but it wont help that much.
(Two cache lines dirtied in tx path, we can do one only)
Better solution is to add tx_packets/tx_bytes/tx_dropped in struct
netdev_queue because this structure is already touched in tx path and
counters updates will then be free (no increase in size)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missed checking of dev_addr_init return value in alloc_netdev_mq.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
net/core/dev.c | 15 ++++++++++++---
1 files changed, 12 insertions(+), 3 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
v5 -> v6 (current):
-removed so far unused static functions
-corrected dev_addr_del_multiple to call del instead of add
v4 -> v5:
-added device address type (suggested by davem)
-removed refcounting (better to have simplier code then safe potentially few
bytes)
v3 -> v4:
-changed kzalloc to kmalloc in __hw_addr_add_ii()
-ASSERT_RTNL() avoided in dev_addr_flush() and dev_addr_init()
v2 -> v3:
-removed unnecessary rcu read locking
-moved dev_addr_flush() calling to ensure no null dereference of dev_addr
v1 -> v2:
-added forgotten ASSERT_RTNL to dev_addr_init and dev_addr_flush
-removed unnecessary rcu_read locking in dev_addr_init
-use compare_ether_addr_64bits instead of compare_ether_addr
-use L1_CACHE_BYTES as size for allocating struct netdev_hw_addr
-use call_rcu instead of rcu_synchronize
-moved is_etherdev_addr into __KERNEL__ ifdef
This patch introduces a new list in struct net_device and brings a set of
functions to handle the work with device address list. The list is a replacement
for the original dev_addr field and because in some situations there is need to
carry several device addresses with the net device. To be backward compatible,
dev_addr is made to point to the first member of the list so original drivers
sees no difference.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based almost entirely upon a patch by Eric Dumazet.
The common case is to have num-tx-queues <= num_rx_queues
and even if num_tx_queues is larger it will not be significantly
larger.
Therefore, a subtraction loop is always going to be faster than
modulus.
Signed-off-by: David S. Miller <davem@davemloft.net>
When skb_rx_queue_recorded() is true, we dont want to use jash distribution
as the device driver exactly told us which queue was selected at RX time.
jhash makes a statistical shuffle, but this wont work with 8 static inputs.
Later improvements would be to compute reciprocal value of real_num_tx_queues
to avoid a divide here. But this computation should be done once,
when real_num_tx_queues is set. This needs a separate patch, and a new
field in struct net_device.
Reported-by: Andrew Dickinson <andrew@whydna.net>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb_gro_* code fails to handle the case where a header starts
in the linear area but ends in the frags area. Since the goal
of skb_gro_* is to optimise the case of completely non-linear
packets, we can simply bail out if we have anything in the linear
area.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This loop over fragments in napi_fraginfo_skb() was "interesting".
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Sidorenko reported:
"while experimenting with 'netem' we have found some strange behaviour. It
seemed that ingress delay as measured by 'ping' command shows up on some
hosts but not on others.
After some investigation I have found that the problem is that skbuff->tstamp
field value depends on whether there are any packet sniffers enabled. That
is:
- if any ptype_all handler is registered, the tstamp field is as expected
- if there are no ptype_all handlers, the tstamp field does not show the delay"
This patch prevents unnecessary update of tstamp in dev_queue_xmit_nit()
on ingress path (with act_mirred) adding a check, so minimal overhead on
the fast path, but only when sniffers etc. are active.
Since netem at ingress seems to logically emulate a network before a host,
tstamp is zeroed to trigger the update and pretend delays are from the
outside.
Reported-by: Alex Sidorenko <alexandre.sidorenko@hp.com>
Tested-by: Alex Sidorenko <alexandre.sidorenko@hp.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that copying a 16-byte area at ~800k times a second
can be really expensive :) This patch redesigns the frags GRO
interface to avoid copying that area twice.
The two disciples of the frags interface have been converted.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since everybody has been focusing on baremetal GRO performance
no one noticed when I added a bug that zapped gso_size for all
GRO packets. This only gets picked up when you forward the skb
out of an interface.
Thanks to Mark Wagner for noticing this bug when testing kvm.
Reported-by: Mark Wagner <mwagner@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netif_device_attach/detach are only stopping one queue. They
should be starting and stopping all the queues on a given device.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO assumes that there is a one-to-one relationship between NAPI
structure and network device. Some devices like sky2 share multiple
devices on a single interrupt so only have one NAPI handler. Rather than
split GRO from NAPI, just have GRO assume if device changes that
it is a different flow.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I fixed the GRO crash in the legacy receive path I used
napi_complete to replace __napi_complete. Unfortunately they're
not the same when NETPOLL is enabled, which may result in us
not calling __napi_complete at all.
What's more, we really do need to keep the __napi_complete call
within the IRQ-off section since in theory an IRQ can occur in
between and fill up the backlog to the maximum, causing us to
lock up.
Since we can't seem to find a fix that works properly right now,
this patch reverts all the GRO support from the netif_rx path.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no gain using prefetch() in dev_hard_start_xmit(), since
we already had to read ops->ndo_select_queue pointer in dev_pick_tx(),
and both pointers are probably located in the same cache line.
This prefetch call slows down fast path because of a stall in address
computation.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor changes to queue hashing:
1. Use const on accessor functions
2. Export skb_tx_hash for use in drivers (see ixgbe)
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct sk_buff pointers should be freed with kfree_skb.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the legacy netif_rx path, I incorrectly tried to optimise
the napi_complete call by using __napi_complete before we reenable
IRQs. This simply doesn't work since we need to flush the held
GRO packets first.
This patch fixes it by doing the obvious thing of reenabling
IRQs first and then calling napi_complete.
Reported-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As my netpoll fix for net doesn't really work for net-next, we
need this update to move the checks into the right place. As it
stands we may pass freed skbs to netpoll_receive_skb.
This patch also introduces a netpoll_rx_on function to avoid GRO
completely if we're invoked through netpoll. This might seem
paranoid but as netpoll may have an external receive hook it's
better to be safe than sorry. I don't think we need this for
2.6.29 though since there's nothing immediately broken by it.
This patch also moves the GRO_* return values to netdevice.h since
VLAN needs them too (I tried to avoid this originally but alas
this seems to be the easiest way out). This fixes a bug in VLAN
where it continued to use the old return value 2 instead of the
correct GRO_DROP.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add FC CRC offload check for ETH_P_FCOE.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As analyzed by Patrick McHardy, vlan needs to reset it's
netdev_ops pointer in it's ->init() function but this
leaves the compat method pointers stale.
Add a netdev_resync_ops() and call it from the vlan code.
Any other driver which changes ->netdev_ops after register_netdevice()
will need to call this new function after doing so too.
With help from Patrick McHardy.
Tested-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that net_alive is unnecessary, and the original problem
that led to it being added was simply that the icmp code thought
it was a network device and wound up being unable to handle packets
while there were still packets in the network namespace.
Now that icmp and tcp have been fixed to properly register themselves
this problem is no longer present and we have a stronger guarantee
that packets will not arrive in a network namespace then that provided
by net_alive in netif_receive_skb. So remove net_alive allowing
packet reception run a little faster.
Additionally document the strong reason why network namespace cleanup
is safe so that if something happens again someone else will have
a chance of figuring it out.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netpoll entry checks are required to ensure that we don't
receive normal packets when invoked via netpoll. Unfortunately
it only ever worked for the netif_receive_skb/netif_rx entry
points. The VLAN (and subsequently GRO) entry point didn't
have the check and therefore can trigger all sorts of weird
problems.
This patch adds the netpoll check to all entry points.
I'm still uneasy with receiving at all under netpoll (which
apparently is only used by the out-of-tree kdump code). The
reason is it is perfectly legal to receive all data including
headers into highmem if netpoll is off, but if you try to do
that with netpoll on and someone gets a printk in an IRQ handler
you're going to get a nice BUG_ON.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that net_alive is unnecessary, and the original problem
that led to it being added was simply that the icmp code thought
it was a network device and wound up being unable to handle packets
while there were still packets in the network namespace.
Now that icmp and tcp have been fixed to properly register themselves
this problem is no longer present and we have a stronger guarantee
that packets will not arrive in a network namespace then that provided
by net_alive in netif_receive_skb. So remove net_alive allowing
packet reception run a little faster.
Additionally document the strong reason why network namespace cleanup
is safe so that if something happens again someone else will have
a chance of figuring it out.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of the TX software time stamping fallback is
faulty because it accesses the skb after ndo_start_xmit() returns
successfully. This patch removes the fallback, which fixes kernel panics
seen during stress tests. Hardware time stamping is not affected by this
removal.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize skb_tx_hash() by eliminating a comparison that executes for
every packet. skb_tx_hashrnd initialization is moved to a later part of
the startup sequence, namely after the "random" driver is initialized.
Rebooted the system three times and verified that the code generates
different random numbers each time.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The additional per-packet information (16 bytes for time stamps, 1
byte for flags) is stored for all packets in the skb_shared_info
struct. This implementation detail is hidden from users of that
information via skb_* accessor functions. A separate struct resp.
union is used for the additional information so that it can be
stored/copied easily outside of skb_shared_info.
Compared to previous implementations (reusing the tstamp field
depending on the context, optional additional structures) this
is the simplest solution. It does not extend sk_buff itself.
TX time stamping is implemented in software if the device driver
doesn't support hardware time stamping.
The new semantic for hardware/software time stamping around
ndo_start_xmit() is based on two assumptions about existing
network device drivers which don't support hardware time
stamping and know nothing about it:
- they leave the new skb_shared_tx unmodified
- the keep the connection to the originating socket in skb->sk
alive, i.e., don't call skb_orphan()
Given that skb_shared_tx is new, the first assumption is safe.
The second is only true for some drivers. As a result, software
TX time stamping currently works with the bnx2 driver, but not
with the unmodified igb driver (the two drivers this patch series
was tested with).
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch optimises the Ethernet header comparison to use 2-byte
and 4-byte xors instead of memcmp. In order to facilitate this,
the actual comparison is now carried out by the callers of the
shared dev_gro_receive function.
This has a significant impact when receiving 1500B packets through
10GbE.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares for the move of the same_flow checks out of
dev_gro_receive. As such we need to remember the number of held
packets since doing a loop just to count them every time is silly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a patch from Atsushi Nemoto <anemo@mba.ocn.ne.jp>
--------------------
The commit 649274d993 ("net_dma:
acquire/release dma channels on ifup/ifdown") added unconditional call
of dmaengine_get() to net_dma. The API should be called only if
NET_DMA was enabled.
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Dan Williams <dan.j.williams@intel.com>
The previous fix ad0f990444 (gro:
Fix handling of imprecisely split packets) only fixed the case
of frags merging, frag_list merging in the same circumstances
were still broken.
In particular, the packet headers end up in the data stream.
This patch fixes this plus another issue where an imprecisely
split packet header may be read incorrectly (this is mostly
harmless since it'll simply cause the packet to not match and
be rejected for GRO).
Thanks to Emil Tantilov and Jeff Kirsher for helping to track
this down.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it currently stands, skb destructors are forbidden on the
receive path because the protocol end-points will overwrite
any existing destructor with their own.
This is the reason why we have to call skb_orphan in the loopback
driver before we reinject the packet back into the stack, thus
creating a period during which loopback traffic isn't charged
to any socket.
With virtualisation, we have a similar problem in that traffic
is reinjected into the stack without being associated with any
socket entity, thus providing no natural congestion push-back
for those poor folks still stuck with UDP.
Now had we been consistent in telling them that UDP simply has
no congestion feedback, I could just fob them off. Unfortunately,
we appear to have gone to some length in catering for this on
the standard UDP path, with skb/socket accounting so that has
created a very unhealthy dependency.
Alas habits are difficult to break out of, so we may just have
to allow skb destructors on the receive path.
It turns out that making skb destructors useable on the receive path
isn't as easy as it seems. For instance, simply adding skb_orphan
to skb_set_owner_r isn't enough. This is because we assume all
over the IP stack that skb->sk is an IP socket if present.
The new transparent proxy code goes one step further and assumes
that skb->sk is the receiving socket if present.
Now all of this can be dealt with by adding simple checks such
as only treating skb->sk as an IP socket if skb->sk->sk_family
matches. However, it turns out that for bridging at least we
don't need to do all of this work.
This is of interest because most virtualisation setups use bridging
so we don't actually go through the IP stack on the host (with
the exception of our old nemesis the bridge netfilter, but that's
easily taken care of).
So this patch simply adds skb_orphan to the point just before we
enter the IP stack, but after we've gone through the bridge on the
receive path. It also adds an skb_orphan to the one place in
netfilter that touches skb->sk/skb->destructor, that is, tproxy.
One word of caution, because of the internal code structure, anyone
wishing to deploy this must use skb_set_owner_w as opposed to
skb_set_owner_r since many functions that create a new skb from
an existing one will invoke skb_set_owner_w on the new skb.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 89a1b249edcf9be884e71f92df84d48355c576aa (gro: Avoid
copying headers of unmerged packets) only worked for packets
which are either completely linear, completely non-linear, or
packets which exactly split at the boundary between headers and
payload.
Anything else would cause bits in the header to go missing if
the packet is held by GRO.
This may have broken drivers such as ixgbe.
This patch fixes the places that assumed or only worked with
the above cases.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch optimises napi_fraginfo_skb to only copy the bits
necessary. We also open-code the memcpy so that the alignment
information is always available to gcc.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately simplicity isn't always the best. The fraginfo
interface turned out to be suboptimal. The problem was quite
obvious. For every packet, we have to copy the headers from
the frags structure into skb->head, even though for 99% of the
packets this part is immediately thrown away after the merge.
LRO didn't have this problem because it directly read the headers
from the frags structure.
This patch attempts to address this by creating an interface
that allows GRO to access the headers in the first frag without
having to copy it. Because all drivers that use frags place the
headers in the first frag this optimisation should be enough.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently VLAN still has a bit of common code handling the aftermath
of GRO that's shared with the common path. This patch moves them
into shared helpers to reduce code duplication.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now only TX hash on pre-computed SKB properties.
The thinking is:
1) High performance routing and firewalling setups will
have a multiqueue capable card used for receive, and
therefore would have RX queue recordings made into
the SKB which can be used for the TX side hash.
2) Locally generated packets will have an attached socket
and thus a valid sk->sk_hash to make use of.
Signed-off-by: David S. Miller <davem@davemloft.net>
The idea is that drivers which implement multiqueue RX
pre-seed the SKB by recording the RX queue selected by
the hardware.
If such a seed is found on TX, we'll use that to select
the outgoing TX queue.
This helps get more consistent load balancing on router
and firewall loads.
Signed-off-by: David S. Miller <davem@davemloft.net>
When a frag is shorter than an Ethernet header, we'd return a
zeroed packet instead of aborting. This patch fixes that.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm trying to track down why people're hitting the checksum warning
in skb_gso_segment. As the problem seems to be hitting lots of
people and I can't reproduce it or locate the bug, here is a patch
to print out more details which hopefully should help us to track
this down.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an init_dummy_netdev() function that gets a network device
structure (allocation and lifetime entirely under caller's control) and
initialize the minimum amount of fields so it can be used to schedule
NAPI polls without registering a full blown interface. This is to be
used by drivers that need to tie several hardware interfaces to a single
NAPI poll scheduler due to HW limitations.
It also updates the ibm_newemac driver to use that, this fixing the
oops on 2.6.29 due to passing NULL as "dev" to netif_napi_add()
Symbol is exported GPL only a I don't think we want binary drivers doing
that sort of acrobatics (if we want them at all).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an skb with page frags is merged into an existing one, we
cannibalise its reference count. This is OK when the skb is
reused because we set nr_frags to zero in that case. However,
for the case where the skb is freed through kfree_skb, we didn't
clear nr_frags which causes the page to be freed prematurely.
This is fixed by moving the skb resetting into skb_gro_receive.
Reported-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As GRO cannot be applied to packets with frag_list we need to
make sure that we reject such packets if they are fed to us,
e.g., through a tunnel device.
Also there is no point in applying GRO on GSO packets so they
too should be rejected. This allows GRO to be used in virtio-net
which may produce GSO packets directly but may still benefit
from GRO if the other end of it doesn't support GSO.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent dmaengine rework removed the capability to remove dma device
driver modules while net_dma is active. Rather than notify
dmaengine-clients that channels are trying to be removed, we now rely on
clients to notify dmaengine when they no longer have a need for
channels. Teach net_dma to release channels by taking dmaengine
references at netdevice open and dropping references at netdevice close.
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (22 commits)
ioat: fix self test for multi-channel case
dmaengine: bump initcall level to arch_initcall
dmaengine: advertise all channels on a device to dma_filter_fn
dmaengine: use idr for registering dma device numbers
dmaengine: add a release for dma class devices and dependent infrastructure
ioat: do not perform removal actions at shutdown
iop-adma: enable module removal
iop-adma: kill debug BUG_ON
iop-adma: let devm do its job, don't duplicate free
dmaengine: kill enum dma_state_client
dmaengine: remove 'bigref' infrastructure
dmaengine: kill struct dma_client and supporting infrastructure
dmaengine: replace dma_async_client_register with dmaengine_get
atmel-mci: convert to dma_request_channel and down-level dma_slave
dmatest: convert to dma_request_channel
dmaengine: introduce dma_request_channel and private channels
net_dma: convert to dma_find_channel
dmaengine: provide a common 'issue_pending_all' implementation
dmaengine: centralize channel allocation, introduce dma_find_channel
dmaengine: up-level reference counting to the module level
...
Previously GRO's only entry point from the outside is through
napi_gro_receive and napi_gro_frags. These interfaces are for
device drivers.
This patch rearranges things to provide a new set of interfaces
for VLANs. These interfaces are for internal use only. The
VLAN code itself can then provide a set of entry points for
device drivers.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users have been converted to either the general-purpose allocator,
dma_find_channel, or dma_request_channel.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that clients no longer need to be notified of channel arrival
dma_async_client_register can simply increment the dmaengine_ref_count.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use the general-purpose channel allocation provided by dmaengine.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
async_tx and net_dma each have open-coded versions of issue_pending_all,
so provide a common routine in dmaengine.
The implementation needs to walk the global device list, so implement
rcu to allow dma_issue_pending_all to run lockless. Clients protect
themselves from channel removal events by holding a dmaengine reference.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch allows GRO to merge page frags (skb_shinfo(skb)->frags)
in one skb, rather than using the less efficient frag_list.
It also adds a new interface, napi_gro_frags to allow drivers
to inject page frags directly into the stack without allocating
an skb. This is intended to be the GRO equivalent for LRO's
lro_receive_frags interface.
The existing GSO interface can already handle page frags with
or without an appended frag_list so nothing needs to be changed
there.
The merging itself is rather simple. We store any new frag entries
after the last existing entry, without checking whether the first
new entry can be merged with the last existing entry. Making this
check would actually be easy but since no existing driver can
produce contiguous frags anyway it would just be mental masturbation.
If the total number of entries would exceed the capacity of a
single skb, we simply resort to using frag_list as we do now.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow GRO packets without frag_list at all, we need to
store the MSS in the packet itself. The obvious place is gso_size.
The only thing to watch out for is if the packet ends up not being
GRO then we need to clear gso_size before pushing the packet into
the stack.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
During network namespace teardown we either move or delete
all of the network devices associated with a network namespace.
In the case of veth devices deleting one will also delete it's
pair device. If both devices are in the same network namespace
then for_each_netdev_safe is insufficient as next may point
to the second veth device we have deleted.
To avoid problems I do what we do in __rtnl_kill_links and
restart the scan of the device list, after we have deleted
a device.
Currently dev_change_netnamespace does not appear to suffer from
this problem, but wireless devices are also paired and likely
should be moved between network namespaces together. So I have
errored on the side of caution and restart the scan of the network
devices in that case as well.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
The initial skb may have been freed after napi_gro_complete in
napi_gro_receive if it was merged into an existing packet. Thus
we cannot check same_flow (which indicates whether it was merged)
after calling napi_gro_complete.
This patch fixes this by saving the same_flow status before the
call to napi_gro_complete.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent GRO patches introduced the NAPI removal of devices in
free_netdev. For drivers that can change the number of queues during
driver operation, the NAPI infrastructure doesn't allow the freeing and
re-addition of NAPI entities without reloading the driver.
This change reinitializes the dev_list in each NAPI struct on delete,
instead of just deleting it (and assigning the list pointers to POISON).
Drivers that wish to remove/re-add NAPI will need to re-initialize the
netdev napi_list after removing all NAPI instances, before re-adding NAPI
devices again.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A command like this: "brctl addif br1 eth1" issued as a user gave me
an oops when bridge module wasn't loaded. It's caused by using a dev
pointer before checking for NULL.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A separate xmit lock class supports GPRS over a Phonet pipe over a TUN
device (type ARPHRD_NONE).
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also leave some room for more 802.11 types.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the top-level GRO (Generic Receive Offload) infrastructure.
This is pretty similar to LRO except that this is protocol-independent.
Instead of holding packets in an lro_mgr structure, they're now held in
napi_struct.
For drivers that intend to use this, they can set the NETIF_F_GRO bit and
call napi_gro_receive instead of netif_receive_skb or just call netif_rx.
The latter will call napi_receive_skb automatically. When napi_gro_receive
is used, the driver must either call napi_complete/napi_rx_complete, or
call napi_gro_flush in softirq context if the driver uses the primitives
__napi_complete/__napi_rx_complete.
Protocols will set the gro_receive and gro_complete function pointers in
order to participate in this scheme.
In addition to the packet, gro_receive will get a list of currently held
packets. Each packet in the list has a same_flow field which is non-zero
if it is a potential match for the new packet. For each packet that may
match, they also have a flush field which is non-zero if the held packet
must not be merged with the new packet.
Once gro_receive has determined that the new skb matches a held packet,
the held packet may be processed immediately if the new skb cannot be
merged with it. In this case gro_receive should return the pointer to
the existing skb in gro_list. Otherwise the new skb should be merged into
the existing packet and NULL should be returned, unless the new skb makes
it impossible for any further merges to be made (e.g., FIN packet) where
the merged skb should be returned.
Whenever the skb is merged into an existing entry, the gro_receive
function should set NAPI_GRO_CB(skb)->same_flow. Note that if an skb
merely matches an existing entry but can't be merged with it, then
this shouldn't be set.
If gro_receive finds it pointless to hold the new skb for future merging,
it should set NAPI_GRO_CB(skb)->flush.
Held packets will be flushed by napi_gro_flush which is called by
napi_complete and napi_rx_complete.
Currently held packets are stored in a singly liked list just like LRO.
The list is limited to a maximum of 8 entries. In future, this may be
expanded to use a hash table to allow more flows to be held for merging.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows GSO to handle frag_list in a limited way for the
purposes of allowing packets merged by GRO to be refragmented on
output.
Most hardware won't (and aren't expected to) support handling GRO
frag_list packets directly. Therefore we will perform GSO in
software for those cases.
However, for drivers that can support it (such as virtual NICs) we
may not have to segment the packets at all.
Whether the added overhead of GRO/GSO is worthwhile for bridges
and routers when weighed against the benefit of potentially
increasing the MTU within the host is still an open question.
However, for the case of host nodes this is undoubtedly a win.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the last shoot of this series.
After I removing all directly reference of netdev->priv, I am killing
"priv" of "struct net_device" and fixing relative comments/docs.
Anyone will not be allowed to reference netdev->priv directly.
If you want to reference the memory of private data, use netdev_priv()
instead.
If the private data is not allocted when alloc_netdev(), use
netdev->ml_priv to point that memory after you creating that private
data.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the network device ops get_stats call to be immutable, the handling
of the default internal network device stats block has to be changed. Add a new
helper function which replaces the old use of internal_get_stats.
Note: change return code to make it clear that the caller should not
go changing the returned statistics.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the network device internal API to move adminstrative
operations out of the network device structure and into a separate structure.
This patch involves some hackery to maintain compatablity between the
new and old model, so all 300+ drivers don't have to be changed at once.
For drivers that aren't converted yet, the netdevice_ops virt function list
still resides in the net_device structure. For old protocols, the new
net_device_ops are copied out to the old net_device pointers.
After the transistion is completed the nag message can be changed to
an WARN_ON, and the compatiablity code can be made configurable.
Some function pointers aren't moved:
* destructor can't be in net_device_ops because
it may need to be referenced after the module is unloaded.
* neighbor setup is manipulated in a couple of places that need special
consideration
* hard_start_xmit is in the fast path for transmit.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Technically, patch changes format for modules, but I think nobody cares.
-86dd :ipv6:ipv6_rcv+0x0
+86dd ipv6_rcv+0x0/0x400 [ipv6]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
security/keys/internal.h
security/keys/process_keys.c
security/keys/request_key.c
Fixed conflicts above by using the non 'tsk' versions.
Signed-off-by: James Morris <jmorris@namei.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: netdev@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
I was recently hunting a bug that occurred in network namespace
cleanup. In looking at the code it became apparrent that we have
and will continue to have cases where if we have anything going
on in a network namespace there will be assumptions that the
loopback device is present. Things like sending igmp unsubscribe
messages when we bring down network devices invokes the routing
code which assumes that at least the loopback driver is present.
Therefore to avoid magic initcall ordering hackery that is hard
to follow and hard to get right insert a call to register the
loopback device directly from net_dev_init(). This guarantes
that the loopback device is the first device registered and
the last network device to go away.
But do it carefully so we register the loopback device after
we clear dev_boot_phase.
Signed-off-by: Eric W. Biederman <ebiederm@maxwell.aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have been tracking for a while a case where when the
network namespace exits the cleanup gets stck in an
endless precessess of:
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
It turns out that if you listen on a multicast address an unsubscribe
packet is sent when the network device goes down. If you shutdown
the network namespace without carefully cleaning up this can trigger
the unsubscribe packet to be sent over the loopback interface while
the network namespace is going down.
All of which is fine except when we drop the packet and forget to
free it leaking the skb and the dst entry attached to. As it
turns out the dst entry hold a reference to the idev which holds
the dev and keeps everything from being cleaned up. Yuck!
By fixing my earlier thinko and add the needed kfree_skb and everything
cleans up beautifully.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was recently hunting a bug that occurred in network namespace
cleanup. In looking at the code it became apparrent that we have
and will continue to have cases where if we have anything going
on in a network namespace there will be assumptions that the
loopback device is present. Things like sending igmp unsubscribe
messages when we bring down network devices invokes the routing
code which assumes that at least the loopback driver is present.
Therefore to avoid magic initcall ordering hackery that is hard
to follow and hard to get right insert a call to register the
loopback device directly from net_dev_init(). This guarantes
that the loopback device is the first device registered and
the last network device to go away.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When physical devices are inside of network namespace and that
network namespace terminates we can not make them go away. We
have to keep them and moving them to the initial network namespace
is the best we can do.
For virtual devices left in a network namespace that is exiting
we have no need to preserve them and we now have the infrastructure
that allows us to delete them. So delete virtual devices when we
exit a network namespace. Keeping the necessary user space clean up
after a network namespace exits much more tractable.
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The changes to deliver hardware accelerated VLAN packets to packet
sockets (commit bc1d0411) caused a warning for non-NAPI drivers.
The __vlan_hwaccel_rx() function is called directly from the drivers
RX function, for non-NAPI drivers that means its still in RX IRQ
context:
[ 27.779463] ------------[ cut here ]------------
[ 27.779509] WARNING: at kernel/softirq.c:136 local_bh_enable+0x37/0x81()
...
[ 27.782520] [<c0264755>] netif_nit_deliver+0x5b/0x75
[ 27.782590] [<c02bba83>] __vlan_hwaccel_rx+0x79/0x162
[ 27.782664] [<f8851c1d>] atl1_intr+0x9a9/0xa7c [atl1]
[ 27.782738] [<c0155b17>] handle_IRQ_event+0x23/0x51
[ 27.782808] [<c015692e>] handle_edge_irq+0xc2/0x102
[ 27.782878] [<c0105fd5>] do_IRQ+0x4d/0x64
Split hardware accelerated VLAN reception into two parts to fix this:
- __vlan_hwaccel_rx just stores the VLAN TCI and performs the VLAN
device lookup, then calls netif_receive_skb()/netif_rx()
- vlan_hwaccel_do_receive(), which is invoked by netif_receive_skb()
in softirq context, performs the real reception and delivery to
packet sockets.
Reported-and-tested-by: Ramon Casellas <ramon.casellas@cttc.es>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gets about 1.25% back on tbench regression.
My change to NAPI for multiqueue support changed the time limit on
network receive processing. Under sustained loads like tbench, this
can cause the receiver to reschedule prematurely.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make testing of the network namespace simpler allow
the network namespace code and the sysfs code to be
compiled and run at the same time. To do this only
virtual devices are allowed in the additional network
namespaces and those virtual devices are not placed
in the kobject tree.
Since virtual devices don't actually do anything interesting
hardware wise that needs device management there should
be no loss in keeping them out of the kobject tree and
by implication sysfs. The gain in ease of testing
and code coverage should be significant.
Changelog:
v2: As pointed out by Benjamin Thery it only makes sense to call
device_rename in the initial network namespace for now.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Tested-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My change
commit e2a6b85247
net: Enable TSO if supported by at least one device
didn't do what was intended because the netdev_compute_features
function was designed for conjunctions. So what happened was that
it would simply take the TSO status of the last constituent device.
This patch extends it to support both conjunctions and disjunctions
under the new name of netdev_increment_features.
It also adds a new function netdev_fix_features which does the
sanity checking that usually occurs upon registration. This ensures
that the computation doesn't result in an illegal combination
since this checking is absent when the change is initiated via
ethtool.
The two users of netdev_compute_features have been converted.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If changename notifier returns an error code, it gets incorrectly
cleared during rollback so the error is never returned to the user.
Found while testing similar code for MTU changes.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some code here depends on CONFIG_KMOD to not try to load
protocol modules or similar, replace by CONFIG_MODULES
where more than just request_module depends on CONFIG_KMOD
and and also use try_then_request_module in ebtables.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Thery tracked down a bug that explains many instances
of the error
unregister_netdevice: waiting for %s to become free. Usage count = %d
It turns out that netdev_run_todo can dead-lock with itself if
a second instance of it is run in a thread that will then free
a reference to the device waited on by the first instance.
The problem is really quite silly. We were trying to create
parallelism where none was required. As netdev_run_todo always
follows a RTNL section, and that todo tasks can only be added
with the RTNL held, by definition you should only need to wait
for the very ones that you've added and be done with it.
There is no need for a second mutex or spinlock.
This is exactly what the following patch does.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer <hawk@comx.dk> reported a bug when setting a VLAN
device down that is in promiscous mode:
When the VLAN device is set down, the promiscous count on the real
device is decremented by one by vlan_dev_stop(). When removing the
promiscous flag from the VLAN device afterwards, the promiscous
count on the real device is decremented a second time by the
vlan_change_rx_flags() callback.
The root cause for this is that the ->change_rx_flags() callback is
invoked while the device is down. The synchronization is meant to mirror
the behaviour of the ->set_rx_mode callbacks, meaning the ->open function
is responsible for doing a full sync on open, the ->close() function is
responsible for doing full cleanup on ->stop() and ->change_rx_flags()
is meant to do incremental changes while the device is UP.
Only invoke ->change_rx_flags() while the device is UP to provide the
intended behaviour.
Tested-by: Jesper Dangaard Brouer <jdb@comx.dk>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add more docbook comments to network device functions and cleanup
the comments.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_change_name and netdev_drivername should use const char on
parameters that are read-only input values. The strcpy to newname is
not needed since newname is not used later in function.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the potentially allocated ifalias when the (new) given alias is empty.
E.g. when setting
echo "" > /sys/class/net/eth0/ifalias
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for keeping an additional character alias
associated with an network interface. This is useful for maintaining
the SNMP ifAlias value which is a user defined value. Routers use this
to hold information like which circuit or line it is connected to. It
is just an arbitrary text label on the network device.
There are two exposed interfaces with this patch, the value can be
read/written either via netlink or sysfs.
This could be maintained just by the snmp daemon, but it is more
generally useful for other management tools, and the kernel is good
place to act as an agreed upon interface to store it.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently simple_tx_hash is hashing inside of udp fragments. As a result
packets are getting getting sent to all queues when they shouldn't be.
This causes a serious performance regression which can be seen by sending
UDP frames larger than mtu on multiqueue devices. This change will make
it so that fragments are hashed only as IP datagrams w/o any protocol
information.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it stands users of netdev_compute_features (e.g., bridges/bonding)
will only enable TSO if all consituent devices support it. This
is unnecessarily pessimistic since even on devices that do not
support hardware TSO and SG, emulated TSO still performs to a par
with TSO off.
This patch enables TSO if at least on constituent device supports
it in hardware.
The direct beneficiaries will be virtualisation that uses bridging
since this means that TSO will always be enabled for communication
from the host to the guests.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_tx_action() can skip __QDISC_STATE_SCHED bit clearing while qdisc
is neither ran nor rescheduled, which may cause endless loop in
dev_deactivate().
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Tested-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If dev_deactivate() is trying to quiesce the queue, it
is theoretically possible for another cpu to livelock
trying to process that queue. This happens because
dev_deactivate() grabs the queue spinlock as it checks
the queue state, whereas net_tx_action() does a trylock
and reschedules the qdisc if it hits the lock.
This breaks the livelock by adding a check on
__QDISC_STATE_DEACTIVATED to net_tx_action() when
the trylock fails.
Based upon feedback from Herbert Xu and Jarek Poplawski.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change handling of the __QDISC_STATE_SCHED flag in net_tx_action() to
enable proper control in dev_deactivate(). Now, if this flag is seen
as unset under root_lock means a qdisc can't be netif_scheduled.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new state lets dev_deactivate() mark a qdisc as having been
deactivated.
dev_queue_xmit() and ing_filter() check for this bit and do not
try to process the qdisc if the bit is set.
dev_deactivate() polls the qdisc after setting the bit, waiting
for both __QDISC_STATE_RUNNING and __QDISC_STATE_SCHED to clear.
This isn't perfect yet, but subsequent changesets will make it so.
This part is just one piece of the puzzle.
Signed-off-by: David S. Miller <davem@davemloft.net>
If a packet_type specifies an active slave to bonding and not just any
interface, allow it to receive frames that came in on that interface.
Signed-off-by: Joe Eykholt <jre@nuovasystems.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Allow a packet_type that specifies the exact device to receive
even on an inactive bonding slave devices. This is important for some
L2 protocols such as LLDP and FCoE. This can eventually be used
for the bonding special cases as well.
Signed-off-by: Joe Eykholt <jre@nuovasystems.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Otherwise subsequent changes need multiple return values.
Signed-off-by: Joe Eykholt <jre@nuovasystems.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Patrick McHardy <kaber@trash.net> noticed that it would be nice to
handle NET_XMIT_BYPASS by NET_XMIT_SUCCESS with an internal qdisc flag
__NET_XMIT_BYPASS and to remove the mapping from dev_queue_xmit().
David Miller <davem@davemloft.net> spotted a serious bug in the first
version of this patch.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the overhead of atomic increment/decrement on each received packet.
This helps performance of non-NAPI devices (like loopback).
Use cleanup function to walk queue on each cpu and clean out any
left over packets.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a netdevice does not support hardware GSO, allowing the stack to
use GSO anyway and then splitting the GSO skb into MSS-sized pieces
as it is handed to the netdevice for transmitting is likely still
a win as far as throughput and/or CPU usage are concerned, since it
reduces the number of trips through the output path.
This patch enables the use of GSO on any netdevice that supports SG.
If a GSO skb is then sent to a netdevice that supports SG but does not
support hardware GSO, net/core/dev.c:dev_hard_start_xmit() will take
care of doing the necessary GSO segmentation in software.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a bug report by Jeff Kirsher.
Don't use qdisc_root_lock() in these cases as the root
qdisc could have been changed, and we'd thus lock the
wrong object.
Tested by Emil S Tantilov who confirms that this seems
to fix the problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
When support for multiple TX queues were added, the
netif_tx_lock() routines we converted to iterate over
all TX queues and grab each queue's spinlock.
This causes heartburn for lockdep and it's not a healthy
thing to do with lots of TX queues anyways.
So modify this to use a top-level lock and a "frozen"
state for the individual TX queues.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug report from Steven Jan Springl:
Issuing the following command causes a kernel oops:
tc qdisc add dev eth0 handle ffff: ingress
The problem mostly stems from all of the special case handling of
ingress qdiscs.
So, to fix this, do the grafting operation the same way we do for TX
qdiscs. Which means that dev_activate() and dev_deactivate() now do
the "qdisc_sleeping <--> qdisc" transitions on dev->rx_queue too.
Future simplifications are possible now, mainly because it is
impossible for dev_queue->{qdisc,qdisc_sleeping} to be NULL. There
are NULL checks all over to handle the ingress qdisc special case
that used to exist before this commit.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netns: fix ip_rt_frag_needed rt_is_expired
netfilter: nf_conntrack_extend: avoid unnecessary "ct->ext" dereferences
netfilter: fix double-free and use-after free
netfilter: arptables in netns for real
netfilter: ip{,6}tables_security: fix future section mismatch
selinux: use nf_register_hooks()
netfilter: ebtables: use nf_register_hooks()
Revert "pkt_sched: sch_sfq: dump a real number of flows"
qeth: use dev->ml_priv instead of dev->priv
syncookies: Make sure ECN is disabled
net: drop unused BUG_TRAP()
net: convert BUG_TRAP to generic WARN_ON
drivers/net: convert BUG_TRAP to generic WARN_ON
Removes legacy reinvent-the-wheel type thing. The generic
machinery integrates much better to automated debugging aids
such as kerneloops.org (and others), and is unambiguous due to
better naming. Non-intuively BUG_TRAP() is actually equal to
WARN_ON() rather than BUG_ON() though some might actually be
promoted to BUG_ON() but I left that to future.
I could make at least one BUILD_BUG_ON conversion.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
pkt_sched: sch_sfq: dump a real number of flows
atm: [fore200e] use MODULE_FIRMWARE() and other suggested cleanups
netfilter: make security table depend on NETFILTER_ADVANCED
tcp: Clear probes_out more aggressively in tcp_ack().
e1000e: fix e1000_netpoll(), remove extraneous e1000_clean_tx_irq() call
net: Update entry in af_family_clock_key_strings
netdev: Remove warning from __netif_schedule().
sky2: don't stop queue on shutdown
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
NR_CPUS: Replace NR_CPUS in speedstep-centrino.c
cpumask: Provide a generic set of CPUMASK_ALLOC macros, FIXUP
NR_CPUS: Replace NR_CPUS in cpufreq userspace routines
NR_CPUS: Replace per_cpu(..., smp_processor_id()) with __get_cpu_var
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genapic_flat_64.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genx2apic_uv_x.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/proc.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/mcheck/mce_64.c
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c, fix
cpumask: Use optimized CPUMASK_ALLOC macros in the centrino_target
cpumask: Provide a generic set of CPUMASK_ALLOC macros
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c
cpumask: Optimize cpumask_of_cpu in kernel/time/tick-common.c
cpumask: Optimize cpumask_of_cpu in drivers/misc/sgi-xp/xpc_main.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/ldt.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/io_apic_64.c
cpumask: Replace cpumask_of_cpu with cpumask_of_cpu_ptr
Revert "cpumask: introduce new APIs"
cpumask: make for_each_cpu_mask a bit smaller
net: Pass reference to cpumask variable in net/sunrpc/svc.c
...
Fix up trivial conflicts in drivers/cpufreq/cpufreq.c manually
It isn't helping anything and we aren't going to be able to change all
the drivers that do queue wakeups in strange situations.
Just letting a noop_qdisc get scheduled will work because when
qdisc_run() executes via net_tx_work() it will simply find no packets
pending when it makes the ->dequeue() call in qdisc_restart.
Signed-off-by: David S. Miller <davem@davemloft.net>
The new address list lock needs to handle the same device layering
issues that the _xmit_lock one does.
This integrates work done by Patrick McHardy.
Signed-off-by: David S. Miller <davem@davemloft.net>
The function header comments have to go with the functions
they are documenting, or things go horribly wrong when we
try to process them with the docbook tools.
Warning(include/linux/netdevice.h:1006): No description found for parameter 'dev_queue'
Warning(include/linux/netdevice.h:1033): No description found for parameter 'dev_queue'
Warning(include/linux/netdevice.h:1067): No description found for parameter 'dev_queue'
Warning(include/linux/netdevice.h:1093): No description found for parameter 'dev_queue'
Warning(include/linux/netdevice.h:1474): No description found for parameter 'txq'
Error(net/core/dev.c:1674): cannot understand prototype: 'u32 simple_tx_hashrnd; '
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Dave:
This patch adds a function to get the driver name from a struct net_device,
and consequently uses this in the watchdog timeout handler to print as
part of the message.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor nit, use size_t for allocation size and kcalloc to allocate
an array. Probably makes no actual code difference.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon feedback from Eric Dumazet and Andi Kleen.
Cure several deficiencies in simple_tx_hash() by using
jhash + reciprocol multiply.
1) Eliminates expensive modulus operation.
2) Makes hash less attackable by using random seed.
3) Eliminates endianness hash distribution issues.
Signed-off-by: David S. Miller <davem@davemloft.net>
Idea is from Patrick McHardy.
Instead of managing the list of qdiscs on the device level, manage it
in the root qdisc of a netdev_queue. This solves all kinds of
visibility issues during qdisc destruction.
The way to iterate over all qdiscs of a netdev_queue is to visit
the netdev_queue->qdisc, and then traverse it's list.
The only special case is to ignore builting qdiscs at the root when
dumping or doing a qdisc_lookup(). That was not needed previously
because builtin qdiscs were not added to the device's qdisc_list.
Signed-off-by: David S. Miller <davem@davemloft.net>
When we have shared qdiscs, packets come out of the qdiscs
for multiple transmit queues.
Therefore it doesn't make any sense to schedule the transmit
queue when logically we cannot know ahead of time the TX
queue of the SKB that the qdisc->dequeue() will give us.
Just for sanity I added a BUG check to make sure we never
get into a state where the noop_qdisc is scheduled.
Signed-off-by: David S. Miller <davem@davemloft.net>
It just xor hashes over IPv4/IPv6 addresses and ports of transport.
The only assumption it makes is that skb_network_header() is set
correctly.
With bug fixes from Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
Devices or device layers can set this to control the queue selection
performed by dev_pick_tx().
This function runs under RCU protection, which allows overriding
functions to have some way of synchronizing with things like dynamic
->real_num_tx_queues adjustments.
This makes the spinlock prefetch in dev_queue_xmit() a little bit
less effective, but that's the price right now for correctness.
Signed-off-by: David S. Miller <davem@davemloft.net>
This effectively "flips the switch" by making the core networking
and multiqueue-aware drivers use the new TX multiqueue structures.
Non-multiqueue drivers need no changes. The interfaces they use such
as netif_stop_queue() degenerate into an operation on TX queue zero.
So everything "just works" for them.
Code that really wants to do "X" to all TX queues now invokes a
routine that does so, such as netif_tx_wake_all_queues(),
netif_tx_stop_all_queues(), etc.
pktgen and netpoll required a little bit more surgery than the others.
In particular the pktgen changes, whilst functional, could be largely
improved. The initial check in pktgen_xmit() will sometimes check the
wrong queue, which is mostly harmless. The thing to do is probably to
invoke fill_packet() earlier.
The bulk of the netpoll changes is to make the code operate solely on
the TX queue indicated by by the SKB queue mapping.
Setting of the SKB queue mapping is entirely confined inside of
net/core/dev.c:dev_pick_tx(). If we end up needing any kind of
special semantics (drops, for example) it will be implemented here.
Finally, we now have a "real_num_tx_queues" which is where the driver
indicates how many TX queues are actually active.
With IGB changes from Jeff Kirsher.
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_netdev_mq() now allocates an array of netdev_queue
structures for TX, based upon the queue_count argument.
Furthermore, all accesses to the TX queues are now vectored
through the netdev_get_tx_queue() and netdev_for_each_tx_queue()
interfaces. This makes it easy to grep the tree for all
things that want to get to a TX queue of a net device.
Problem spots which are not really multiqueue aware yet, and
only work with one queue, can easily be spotted by grepping
for all netdev_get_tx_queue() calls that pass in a zero index.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a specific lock to protect the network
device unicast and multicast lists, remove extraneous
grabs of the TX lock in cases where the code only needs
address list protection.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_addr_{lock,unlock}{,_bh}() helpers.
Use them to protect operations that operate on or read
the network device unicast and multicast address lists.
Also use them in cases where the code simply wants to
block calls into the driver's ->set_rx_mode() and
->set_multicast_list() methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used to protect the per-device unicast and multicast
address lists, as well as the callbacks into the drivers which
configure such state such as ->set_rx_mode() and ->set_multicast_list().
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN header stripping is used, packets currently bypass packet
sockets (and other network taps) completely. For locally existing
VLANs, they appear directly on the VLAN device, for unknown VLANs
they are silently dropped.
Add a new function netif_nit_deliver() to deliver incoming packets
to all network interface taps and use it in __vlan_hwaccel_rx() to
make VLAN packets visible on the underlying device.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'core/softirq' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
softirq: remove irqs_disabled warning from local_bh_enable
softirq: remove initialization of static per-cpu variable
Remove argument from open_softirq which is always NULL
Accesses are mostly structured such that when there are multiple TX
queues the code transformations will be a little bit simpler.
Signed-off-by: David S. Miller <davem@davemloft.net>
Only plain netif_schedule() remains taking a net_device, mostly as a
compatability item while we transition the rest of these interfaces.
Everything else calls netif_schedule_queue() or __netif_schedule(),
both of which take a netdev_queue pointer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that our qdisc management is bi-directional, per-queue, and fully
orthogonal, there is no reason to have a special ingress qdisc pointer
in struct net_device.
Signed-off-by: David S. Miller <davem@davemloft.net>
Every qdisc is assosciated with a queue, and in the case of ingress
qdiscs that will now be netdev->rx_queue so using that queue's lock is
the thing to do.
Signed-off-by: David S. Miller <davem@davemloft.net>
The lock is now an attribute of the device queue.
One thing to notice is that "suspicious" places
emerge which will need specific training about
multiple queue handling. They are so marked with
explicit "netdev->rx_queue" and "netdev->tx_queue"
references.
Signed-off-by: David S. Miller <davem@davemloft.net>
A netdev_queue is an entity managed by a qdisc.
Currently there is one RX and one TX queue, and a netdev_queue merely
contains a backpointer to the net_device.
The Qdisc struct is augmented with a netdev_queue pointer as well.
Eventually the 'dev' Qdisc member will go away and we will have the
resulting hierarchy:
net_device --> netdev_queue --> Qdisc
Also, qdisc_alloc() and qdisc_create_dflt() now take a netdev_queue
pointer argument.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dad9b335 (netdevice: Fix promiscuity and allmulti overflow) broke
dev_set_promiscuity() by returning on success without reprogramming the
device.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
v1->v2: Use strlcpy() to ensure s[i].name be null-termination.
1. In netdev_boot_setup_add(), a long name will leak.
ex. : dev=21,0x1234,0x1234,0x2345,eth123456789verylongname.........
2. In netdev_boot_setup_check(), mismatch will happen if s[i].name
is a substring of dev->name.
ex. : dev=...eth1 dev=...eth11
[ With feedback from Ben Hutchings. ]
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Large Receive Offload (LRO) is only appropriate for packets that are
destined for the host, and should be disabled if received packets may be
forwarded. It can also confuse the GSO on output.
Add dev_disable_lro() function which uses the appropriate ethtool ops to
disable LRO if enabled.
Add calls to dev_disable_lro() in br_add_if() and functions that enable
IPv4 and IPv6 forwarding.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Max of promiscuity and allmulti plus positive @inc can cause overflow.
Fox example: when allmulti=0xFFFFFFFF, any caller give dev_set_allmulti() a
positive @inc will cause allmulti be off.
This is not what we want, though it's rare case.
The fix is that only negative @inc will cause allmulti or promiscuity be off
and when any caller makes the counters touch the roof, we return error.
Change of v2:
Change void function dev_set_promiscuity/allmulti to return int.
So callers can get the overflow error.
Caller's fix will be done later.
Change of v3:
1. Since we return error to caller, we don't need to print KERN_ERROR,
KERN_WARNING is enough.
2. In dev_set_promiscuity(), if __dev_set_promiscuity() failed, we
return at once.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NETDEV_BONDING_FAILOVER event to be used in a successive patch
by bonding to announce fail-over for the active-backup mode through the
netdev events notifier chain mechanism. Such an event can be of use for the
RDMA CM (communication manager) to let native RDMA ULPs (eg NFS-RDMA, iSER)
always be aligned with the IP stack, in the sense that they use the same
ports/links as the stack does. More usages can be done to allow monitoring
tools based on netlink events being aware to bonding fail-over.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Selected device feature bits can be propagated to VLAN devices, so we
can make use of TX checksum offload and TSO on VLAN-tagged packets.
However, if the physical device does not do VLAN tag insertion or
generic checksum offload then the test for TX checksum offload in
dev_queue_xmit() will see a protocol of htons(ETH_P_8021Q) and yield
false.
This splits the checksum offload test into two functions:
- can_checksum_protocol() tests a given protocol against a feature bitmask
- dev_can_checksum() first tests the skb protocol against the device
features; if that fails and the protocol is htons(ETH_P_8021Q) then
it tests the encapsulated protocol against the effective device
features for VLANs
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As git-grep shows, open_softirq() is always called with the last argument
being NULL
block/blk-core.c: open_softirq(BLOCK_SOFTIRQ, blk_done_softirq, NULL);
kernel/hrtimer.c: open_softirq(HRTIMER_SOFTIRQ, run_hrtimer_softirq, NULL);
kernel/rcuclassic.c: open_softirq(RCU_SOFTIRQ, rcu_process_callbacks, NULL);
kernel/rcupreempt.c: open_softirq(RCU_SOFTIRQ, rcu_process_callbacks, NULL);
kernel/sched.c: open_softirq(SCHED_SOFTIRQ, run_rebalance_domains, NULL);
kernel/softirq.c: open_softirq(TASKLET_SOFTIRQ, tasklet_action, NULL);
kernel/softirq.c: open_softirq(HI_SOFTIRQ, tasklet_hi_action, NULL);
kernel/timer.c: open_softirq(TIMER_SOFTIRQ, run_timer_softirq, NULL);
net/core/dev.c: open_softirq(NET_TX_SOFTIRQ, net_tx_action, NULL);
net/core/dev.c: open_softirq(NET_RX_SOFTIRQ, net_rx_action, NULL);
This observation has already been made by Matthew Wilcox in June 2002
(http://www.cs.helsinki.fi/linux/linux-kernel/2002-25/0687.html)
"I notice that none of the current softirq routines use the data element
passed to them."
and the situation hasn't changed since them. So it appears we can safely
remove that extra argument to save 128 (54) bytes of kernel data (text).
Signed-off-by: Carlos R. Mafra <crmafra@ift.unesp.br>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change references from for_each_cpu_mask to for_each_cpu_mask_nr
where appropriate
Reviewed-by: Paul Jackson <pj@sgi.com>
Reviewed-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Am I just being particularly dim today, or can the call to
dev->change_rx_flags(dev, IFF_MULTICAST) in dev_change_flags() never
happen?
We've just set dev->flags = flags & IFF_MULTICAST, effectively. So the
condition '(dev->flags ^ flags) & IFF_MULTICAST' is _never_ going to be
true.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
device_rename can fail with -EEXIST or -ENOMEM, so handle any
problems.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_open() and dev_close() must be called holding the RTNL, since they
call device functions and netdevice notifiers that are promised the RTNL.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a net namespace is destroyed, some devices (those, not killed
on ns stop explicitly) are moved back to init_net.
The problem, is that this net_ns change has one point of failure -
the __dev_alloc_name() may be called if a name collision occurs (and
this is easy to trigger). This allocator performs a likely-to-fail
GFP_ATOMIC allocation to find a suitable number. Other possible
conditions that may cause error (for device being ns local or not
registered) are always false in this case.
So, when this call fails, the device is unregistered. But this is
*not* the right thing to do, since after this the device may be
released (and kfree-ed) improperly. E. g. bridges require more
actions (sysfs update, timer disarming, etc.), some other devices
want to remove their private areas from lists, etc.
I. e. arbitrary use-after-free cases may occur.
The proposed fix is the following: since the only reason for the
dev_change_net_namespace to fail is the name generation, we may
give it a unique fall-back name w/o %d-s in it - the dev<ifindex>
one, since ifindexes are still unique.
So make this change, raise the failure-case printk loglevel to
EMERG and replace the unregister_netdevice call with BUG().
[ Use snprintf() -DaveM ]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a netdev is moved across namespaces with the
'dev_change_net_namespace' function, the 'device_rename' function is
used to fixup kobject and refresh the sysfs tree. The device_rename
function will call kobject_rename and this one will check if there is
an object with the same name and this is the case because we are
renaming the object with the same name.
The use of 'device_rename' seems for me wrong because we usually don't
rename it but just move it across namespaces. As we just want to do a
mini "netdev_[un]register", IMO the functions
'netdev_[un]register_kobject' should be used instead, like an usual
network device [un]registering.
This patch replace device_rename by netdev_unregister_kobject,
followed by netdev_register_kobject.
The netdev_register_kobject will call device_initialize and will raise
a warning indicating the device was already initialized. In order to
fix that, I split the device initialization into a separate function
and use it together with 'netdev_register_kobject' into
register_netdevice. So we can safely call 'netdev_register_kobject' in
'dev_change_net_namespace'.
This fix will allow to properly use the sysfs per namespace which is
coming from -mm tree.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the fixed size channels[NR_CPUS] array in net/core/dev.c and
dynamically allocate array based on nr_cpu_ids.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers have duplicated unlikely() macros. IS_ERR() already has
unlikely() in itself.
This patch cleans up such pointless code.
Signed-off-by: Hirofumi Nakagawa <hnakagawa@miraclelinux.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch effectively reverts commit d0498d9ae1
aka "[NET]: Do not allocate unneeded memory for dev->priv alignment."
It was found to be buggy because of final unconditional += NETDEV_ALIGN_CONST
removal.
For example, for sizeof(struct net_device) being 2048 bytes, "alloc_size"
was also 2048 bytes, but allocator with debugging options turned on started
giving out !32-byte aligned memory resulting in redzones overwrites.
Patch does small optimization in ->priv'less case: bumping size to next
32-byte boundary was always done to ensure ->priv will also be aligned.
But, no ->priv, no need to do that.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The alloc_netdev_mq() tries to produce 32-bytes alignment for both
the net_device itself and its private data. The second alignment is
achieved by adding the NETDEV_ALIGN_CONST to the whole size of
the memory to be allocated.
However, for those devices that do not need the private area, this
addition just makes the net_device weight 1024 + 32 = 1068 bytes,
i.e. consume twice as much memory.
Since loopback device is such (sizeof_priv == 0 for it), and each
net namespace creates one, this can save a noticeable amount of
memory for kernel with net namespaces turned on.
After this set the lo device is actually allocated from a size-1024
kmem cache on i386 box even with NETPOLL and WIRELESS_EXT turned on.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_set_net is called for
- just allocated devices
- devices moving from one namespace to another
release_net has proper check inside to distinguish these cases.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIOCADDMULTI/SIOCDELMULTI check whether the driver has a set_multicast_list
method to determine whether it supports multicast. Drivers implementing
secondary unicast support use set_rx_mode however.
Check for both dev->set_multicast_mode and dev->set_rx_mode to determine
multicast capabilities.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an inline net_eq() to compare two namespaces.
Without CONFIG_NET_NS, since no namespace other than &init_net
exists, it is always 1.
We do not need to convert 1) inline vs inline and
2) inline vs &init_net comparisons.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Introduce per-net_device inlines: dev_net(), dev_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
This file displays the registered packet types, but some of them
(packet sockets creates such) can be bound to a net device and showing
them in a wrong namespace is not correct.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update: My mailer ate one of Jarek's feedback mails... Fixed the
parameter in netif_set_gso_max_size() to be u32, not u16. Fixed the
whitespace issue due to a patch import botch. Changed the types from
u32 to unsigned int to be more consistent with other variables in the
area. Also brought the patch up to the latest net-2.6.26 tree.
Update: Made gso_max_size container 32 bits, not 16. Moved the
location of gso_max_size within netdev to be less hotpath. Made more
consistent names between the sock and netdev layers, and added a
define for the max GSO size.
Update: Respun for net-2.6.26 tree.
Update: changed max_gso_frame_size and sk_gso_max_size from signed to
unsigned - thanks Stephen!
This patch adds the ability for device drivers to control the size of
the TSO frames being sent to them, per TCP connection. By setting the
netdevice's gso_max_size value, the socket layer will set the GSO
frame size based on that value. This will propogate into the TCP
layer, and send TSO's of that size to the hardware.
This can be desirable to help tune the bursty nature of TSO on a
per-adapter basis, where one may have 1 GbE and 10 GbE devices
coexisting in a system, one running multiqueue and the other not, etc.
This can also be desirable for devices that cannot support full 64 KB
TSO's, but still want to benefit from some level of segmentation
offloading.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
[NETFILTER]: fix ebtable targets return
[IP_TUNNEL]: Don't limit the number of tunnels with generic name explicitly.
[NET]: Restore sanity wrt. print_mac().
[NEIGH]: Fix race between neighbor lookup and table's hash_rnd update.
[RTNL]: Validate hardware and broadcast address attribute for RTM_NEWLINK
tg3: ethtool phys_id default
[BNX2]: Update version to 1.7.4.
[BNX2]: Disable parallel detect on an HP blade.
[BNX2]: More 5706S link down workaround.
ssb: Fix support for PCI devices behind a SSB->PCI bridge
zd1211rw: fix sparse warnings
rtl818x: fix sparse warnings
ssb: Fix pcicore cardbus mode
ssb: Make the GPIO API reentrancy safe
ssb: Fix the GPIO API
ssb: Fix watchdog access for devices without a chipcommon
ssb: Fix serial console on new bcm47xx devices
ath5k: Fix build warnings on some 64-bit platforms.
WDEV, ath5k, don't return int from bool function
WDEV: ath5k, fix lock imbalance
...
Commit a0a400d79e ("[NET]: dev_mcast:
add multicast list synchronization helpers") from you introduced a new
field "da_synced" to struct dev_addr_list that is not properly
initialized to 0. So when any of the current users (8021q, macvlan,
mac80211) calls dev_mc_sync/unsync they mess the address list for both
devices.
The attached patch fixed it for me and avoid future problems.
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (82 commits)
[NET]: Make sure sockets implement splice_read
netconsole: avoid null pointer dereference at show_local_mac()
[IPV6]: Fix reversed local_df test in ip6_fragment
[XFRM]: Avoid bogus BUG() when throwing new policy away.
[AF_KEY]: Fix bug in spdadd
[NETFILTER] nf_conntrack_proto_tcp.c: Mistyped state corrected.
net: xfrm statistics depend on INET
[NETFILTER]: make secmark_tg_destroy() static
[INET]: Unexport inet_listen_wlock
[INET]: Unexport __inet_hash_connect
[NET]: Improve cache line coherency of ingress qdisc
[NET]: Fix race in dev_close(). (Bug 9750)
[IPSEC]: Fix bogus usage of u64 on input sequence number
[RTNETLINK]: Send a single notification on device state changes.
[NETLABLE]: Hide netlbl_unlabel_audit_addr6 under ifdef CONFIG_IPV6.
[NETLABEL]: Don't produce unused variables when IPv6 is off.
[NETLABEL]: Compilation for CONFIG_AUDIT=n case.
[GENETLINK]: Relax dances with genl_lock.
[NETLABEL]: Fix lookup logic of netlbl_domhsh_search_def.
[IPV6]: remove unused method declaration (net/ndisc.h).
...
Move networking (core and drivers) docbook to its own networking book.
Fix a few kernel-doc errors in header and source files.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fastcall always expands to empty, remove it.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a race in Linux kernel file net/core/dev.c, function dev_close.
The function calls function dev_deactivate, which calls function
dev_watchdog_down that deletes the watchdog timer. However, after that, a
driver can call netif_carrier_ok, which calls function
__netdev_watchdog_up that can add the watchdog timer again. Function
unregister_netdevice calls function dev_shutdown that traps the bug
!timer_pending(&dev->watchdog_timer). Moving dev_deactivate after
netif_running() has been cleared prevents function netif_carrier_on
from calling __netdev_watchdog_up and adding the watchdog timer again.
Signed-off-by: Matti Linnanvuori <mattilinnanvuori@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes the ANOM_PROMISCUOUS message to include uid and gid fields,
making it consistent with other AUDIT_ANOM_ messages and in the
format the userspace is expecting.
Signed-off-by: Klaus Heinrich Kiwi <klausk@br.ibm.com>
Acked-by: Eric Paris <eparis@redhat.com>
In order to correlate audit records to an individual login add a session
id. This is incremented every time a user logs in and is included in
almost all messages which currently output the auid. The field is
labeled ses= or oses=
Signed-off-by: Eric Paris <eparis@redhat.com>
Reuse the existing logic for multicast list synchronization for the
unicast address list. The core of dev_mc_sync/unsync are split out as
__dev_addr_sync/unsync and moved from dev_mcast.c to dev.c. These are
then used to implement dev_unicast_sync/unsync as well.
I'm working on cleaning up Intel's FCoE stack, which generates new MAC
addresses from the fibre channel device id assigned by the fabric as
per the current draft specification in T11. When using such a
protocol in a VLAN environment it would be nice to not always be
forced into promiscuous mode, assuming the underlying Ethernet driver
supports multiple unicast addresses as well.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Add __acquires() and __releases() annotations to suppress some sparse
warnings.
example of warnings :
net/ipv4/udp.c:1555:14: warning: context imbalance in 'udp_seq_start' - wrong
count at exit
net/ipv4/udp.c:1571:13: warning: context imbalance in 'udp_seq_stop' -
unexpected unlock
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller must hold the RTNL so let's check it in unregister_netdevice.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
single list_head variable initialized with LIST_HEAD_INIT could almost
always can be replaced with LIST_HEAD declaration, this shrinks the code
and looks better.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently this size is 16, but as the comment says this
is so only because all the chains (except one) has the
length 1. I think, that some day this may change, so
growing this hash will be much easier.
Besides, symbolic names are read better than magic constants.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This finally adds the code in net_rx_action() to break out of the
->poll()'ing loop when a napi_disable() is found to be pending.
Now, even if a device is being flooded with packets it can be cleanly
brought down.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some return value comments for void functions.
Fixed it.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fcc5a03ac42564e9e255c1134dda47442289e466:
[NET]: Allow netdev REGISTER/CHANGENAME events to fail
makes the register_netdevice_notifier() handle the error from the
NETDEV_REGISTER event, sent to the registering block.
The bad news is that in this case the notifier block is
not removed from the list, but the error is returned to the
caller. In case the caller is in module init function and
handles this error this can abort the module loading. The
notifier block will be then removed from the kernel, but
will be left in the list. Oops :(
I think that the notifier block should be removed from the
chain in case of error, regardless whether this error is
handled by the caller or not. In the worst case (the error
is _not_ handled) module will not receive the events any
longer.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts Eric's commit 2b008b0a8e
It diets .text & .data section of the kernel if CONFIG_NET_NS is not set.
This is safe after list operations cleanup.
Signed-of-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* it already statically initialized
* reinitializing live global spinlock every time netns is
setup is also wrong
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation updates for network interfaces.
1. Add doc for netif_napi_add
2. Remove doc for unused returns from netif_rx
3. Add doc for netif_receive_skb
[ Incorporated minor mods from Randy Dunlap -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Point 1:
The unregistering of a network device schedule a netdev_run_todo.
This function calls dev->destructor when it is set and the
destructor calls free_netdev.
Point 2:
In the case of an initialization of a network device the usual code
is:
* alloc_netdev
* register_netdev
-> if this one fails, call free_netdev and exit with error.
Point 3:
In the register_netdevice function at the later state, when the device
is at the registered state, a call to the netdevice_notifiers is made.
If one of the notification falls into an error, a rollback to the
registered state is done using unregister_netdevice.
Conclusion:
When a network device fails to register during initialization because
one network subsystem returned an error during a notification call
chain, the network device is freed twice because of fact 1 and fact 2.
The second free_netdev will be done with an invalid pointer.
Proposed solution:
The following patch move all the code of unregister_netdevice *except*
the call to net_set_todo, to a new function "rollback_registered".
The following functions are changed in this way:
* register_netdevice: calls rollback_registered when a notification fails
* unregister_netdevice: calls rollback_register + net_set_todo, the call
order to net_set_todo is changed because it is the
latest now. Since it justs add an element to a list
that should not break anything.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netpoll_poll_lock() synchronizes the ->poll() invocation
code paths, but once we have the lock we have to make
sure that NAPI_STATE_SCHED is still set. Otherwise we
get:
cpu 0 cpu 1
net_rx_action() poll_napi()
netpoll_poll_lock() ... spin on ->poll_lock
->poll()
netif_rx_complete
netpoll_poll_unlock() acquire ->poll_lock()
->poll()
netif_rx_complete()
CRASH
Based upon a bug report from Tina Yang.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not safe to to place struct pernet_operations in a special section.
We need struct pernet_operations to last until we call unregister_pernet_subsys.
Which doesn't happen until module unload.
So marking struct pernet_operations is a disaster for modules in two ways.
- We discard it before we call the exit method it points to.
- Because I keep struct pernet_operations on a linked list discarding
it for compiled in code removes elements in the middle of a linked
list and does horrible things for linked insert.
So this looks safe assuming __exit_refok is not discarded
for modules.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent error/backtrace from dev_rename() when changing
name of network device to the same name. This is a common
situation with udev and other scripts that bind addr to device.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inconsistent prototype and real type for functions may have worse
consequences, than those for variables, so move them into a header.
Since they are used privately in net/core, make this file reside in
the same place.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many places get the queue_mapping field from skb to pass it to the
netif_subqueue_stopped() which will be 0 in any case.
Make the helper that works with sk_buff
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's already such a helper to initialize this field. Use it.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP packets all have writable heads, that is, even though it's cloned, it is
writable up to the end of the TCP header. This patch makes skb_checksum_help
aware of this fact by using skb_clone_writable and avoiding a copy for TCP.
I've also modified the BUG_ON tests to be unsigned. The only case where this
makes a difference is if csum_start points to a location before skb->data.
Since skb->data should always include the header where the checksum field
is (and all currently callers adhere to that), this change is safe and may
uncover bugs later.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it is we always invoke pt_prev before ing_filter, even if there are no
ingress filters attached. This can cause unnecessary cloning in pt_prev.
This patch changes it so that we only invoke pt_prev if there are ingress
filters attached.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix networking code kernel-doc for newly added parameters.
Warning(linux-2.6.23-git2//net/core/sock.c:879): No description found for parameter 'net'
Warning(linux-2.6.23-git2//net/core/dev.c:570): No description found for parameter 'net'
Warning(linux-2.6.23-git2//net/core/dev.c:594): No description found for parameter 'net'
Warning(linux-2.6.23-git2//net/core/dev.c:617): No description found for parameter 'net'
Warning(linux-2.6.23-git2//net/core/dev.c:641): No description found for parameter 'net'
Warning(linux-2.6.23-git2//net/core/dev.c:667): No description found for parameter 'net'
Warning(linux-2.6.23-git2//net/core/dev.c:722): No description found for parameter 'net'
Warning(linux-2.6.23-git2//net/core/dev.c:959): No description found for parameter 'net'
Warning(linux-2.6.23-git2//net/core/dev.c:1195): No description found for parameter 'dev'
Warning(linux-2.6.23-git2//net/core/dev.c:2105): No description found for parameter 'n'
Warning(linux-2.6.23-git2//net/core/dev.c:3272): No description found for parameter 'net'
Warning(linux-2.6.23-git2//net/core/dev.c:3445): No description found for parameter 'net'
Warning(linux-2.6.23-git2//include/linux/netdevice.h:1301): No description found for parameter 'cpu'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The unregister_netdevice() and dev_change_net_namespace()
both check for dev->flags to be IFF_UP before calling the
dev_close(), but the dev_close() checks for IFF_UP itself,
so remove those unneeded checks.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the net namespaces many code leaved the __init section,
thus making the kernel occupy more memory than it did before.
Since we have a config option that prohibits the namespace
creation, the functions that initialize/finalize some netns
stuff are simply not needed and can be freed after the boot.
Currently, this is almost not noticeable, since few calls
are no longer in __init, but when the namespaces will be
merged it will be possible to free more code. I propose to
use the __net_init, __net_exit and __net_initdata "attributes"
for functions/variables that are not used if the CONFIG_NET_NS
is not set to save more space in memory.
The exiting functions cannot just reside in the __exit section,
as noticed by David, since the init section will have
references on it and the compilation will fail due to modpost
checks. These references can exist, since the init namespace
never dies and the exit callbacks are never called. So I
introduce the __exit_refok attribute just like it is already
done with the __init_refok.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This always bugged me: dev_ioctl() called dev_ifsioc() either inside
read_lock(dev_base_lock) or rtnl_lock(), depending on the ioctl being
executed.
This change moves the ioctls executed inside dev_base_lock to a new
function, dev_ifsioc_locked(). Now the locking context is completely
clear to the reader.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bunch of sparse warnings. Mostly about 0 used as
NULL pointer, and shadowed variable declarations.
One notable case was that hash size should have been unsigned.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hardware header operations are part of the protocol class
not the device instance, make them into a separate object and
save memory.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sysfs support is compiled out the kernel still keeps and maintains
the kobject tree. So it is not safe to skip our kobject reference counting or
to avoid becoming members of the kobject tree. It is safe to not add
the networking specific sysfs attributes.
This patch removes the sysfs special cases from net/core/dev.c
renames functions from netdev_sysfs_xxxx to netdev_kobject_xxxx
and always compiles in net-sysfs.c
net-sysfs.c is modified with a CONFIG_SYSFS guard around the parts
that are actually sysfs specific.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call_netdev_notifiers routine can successfully be used in
the net/core_dev.c itself.
This will save 6 lines of code and 62 ;) bytes of .text section.
62 is rather small, but I have one more patch saving ~30 bytes
from netns code (sent to Eric), so altogether they can save
some more noticeable amount.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_name_hash and the dev_index_hash are now booth kmalloc-ed
(and each element is properly initialized as usually) so I think
it's worth consolidating this code making it look nicer (and
saving 28 bytes of .text section ;) )
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces the void * parameter with a struct net_device * which
is what is actually required.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HARD_TX_LOCK micro is a nice aggregation that could be used
in other spots. move it to netdevice.h
Also makes sure the previously superflous cpu arguement is used.
Thanks to DaveM for the suggestions.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem: proc_net files remember which network namespace the are
against but do not remember hold a reference count (as that would pin
the network namespace). So we currently have a small window where
the reference count on a network namespace may be incremented when opening
a /proc file when it has already gone to zero.
To fix this introduce maybe_get_net and get_proc_net.
maybe_get_net increments the network namespace reference count only if it is
greater then zero, ensuring we don't increment a reference count after it
has gone to zero.
get_proc_net handles all of the magic to go from a proc inode to the network
namespace instance and call maybe_get_net on it.
PROC_NET the old accessor is removed so that we don't get confused and use
the wrong helper function.
Then I fix up the callers to use get_proc_net and handle the case case
where get_proc_net returns NULL. In that case I return -ENXIO because
effectively the network namespace has already gone away so the files
we are trying to access don't exist anymore.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces NETIF_F_NETNS_LOCAL a flag to indicate
a network device is local to a single network namespace and
should never be moved. Useful for pseudo devices that we
need an instance in each network namespace (like the loopback
device) and for any device we find that cannot handle multiple
network namespaces so we may trap them in the initial network
namespace.
This patch introduces the function dev_change_net_namespace
a function used to move a network device from one network
namespace to another. To the network device nothing
special appears to happen, to the components of the network
stack it appears as if the network device was unregistered
in the network namespace it is in, and a new device
was registered in the network namespace the device
was moved to.
This patch sets up a namespace device destructor that
upon the exit of a network namespace moves all of the
movable network devices to the initial network namespace
so they are not lost.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When forcibly changing the network namespace of a device
I need something that can generate a name for the device
in the new namespace without overwriting the old name.
__dev_alloc_name provides me that functionality.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes most of the generic device layer network
namespace safe. This patch makes dev_base_head a
network namespace variable, and then it picks up
a few associated variables. The functions:
dev_getbyhwaddr
dev_getfirsthwbytype
dev_get_by_flags
dev_get_by_name
__dev_get_by_name
dev_get_by_index
__dev_get_by_index
dev_ioctl
dev_ethtool
dev_load
wireless_process_ioctl
were modified to take a network namespace argument, and
deal with it.
vlan_ioctl_set and brioctl_set were modified so their
hooks will receive a network namespace argument.
So basically anthing in the core of the network stack that was
affected to by the change of dev_base was modified to handle
multiple network namespaces. The rest of the network stack was
simply modified to explicitly use &init_net the initial network
namespace. This can be fixed when those components of the network
stack are modified to handle multiple network namespaces.
For now the ifindex generator is left global.
Fundametally ifindex numbers are per namespace, or else
we will have corner case problems with migration when
we get that far.
At the same time there are assumptions in the network stack
that the ifindex of a network device won't change. Making
the ifindex number global seems a good compromise until
the network stack can cope with ifindex changes when
you change namespaces, and the like.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for carefully selected pseudo devices all network
interfaces should start out in the initial network namespace.
Ultimately it will be register_netdev that examines what
dev->nd_net is set to and places a device in a network namespace.
This patch modifies alloc_netdev to initialize the network
namespace a device is in with the initial network namespace.
This gets it right for the vast majority of devices so their
drivers need not be modified and for those few pseudo devices
that need something different they can change this parameter
before calling register_netdevice.
The network namespace parameter on a network device is not
reference counted as the devices are inside of a network namespace
and cannot remain in that namespace past the lifetime of the
network namespace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes /proc/net per network namespace. It modifies the global
variables proc_net and proc_net_stat to be per network namespace.
The proc_net file helpers are modified to take a network namespace argument,
and all of their callers are fixed to pass &init_net for that argument.
This ensures that all of the /proc/net files are only visible and
usable in the initial network namespace until the code behind them
has been updated to be handle multiple network namespaces.
Making /proc/net per namespace is necessary as at least some files
in /proc/net depend upon the set of network devices which is per
network namespace, and even more files in /proc/net have contents
that are relevant to a single network namespace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.
In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.
The signature of the ->poll() call back goes from:
int foo_poll(struct net_device *dev, int *budget)
to
int foo_poll(struct napi_struct *napi, int budget)
The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract). The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.
The napi_struct is to be embedded in the device driver private data
structures.
Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler. Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.
With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.
Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.
[ Ported to current tree and all drivers converted. Integrated
Stephen's follow-on kerneldoc additions, and restored poll_list
handling to the old style to fix mutual exclusion issues. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
http://bugzilla.kernel.org/show_bug.cgi?id=8797 shows that the
bonding driver may produce bogus combinations of the checksum
flags and SG/TSO.
For example, if you bond devices with NETIF_F_HW_CSUM and
NETIF_F_IP_CSUM you'll end up with a bonding device that
has neither flag set. If both have TSO then this produces
an illegal combination.
The bridge device on the other hand has the correct code to
deal with this.
In fact, the same code can be used for both. So this patch
moves that logic into net/core/dev.c and uses it for both
bonding and bridging.
In the process I've made small adjustments such as only
setting GSO_ROBUST if at least one constituent device
supports it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to allow errors to be passed up from event
handlers of NETDEV_REGISTER and NETDEV_CHANGENAME. It also adds
the notifier_from_errno/notifier_to_errnor helpers to pass the
errno value up to the notifier caller.
If an error is detected when a device is registered, it causes
that operation to fail. A NETDEV_UNREGISTER will be sent to
all event handlers.
Similarly if NETDEV_CHANGENAME fails the original name is restored
and a new NETDEV_CHANGENAME event is sent.
As such all event handlers must be idempotent with respect to
these events.
When an event handler is registered NETDEV_REGISTER events are
sent for all devices currently registered. Should any of them
fail, we will send NETDEV_GOING_DOWN/NETDEV_DOWN/NETDEV_UNREGISTER
events to that handler for the devices which have already been
registered with it. The handler registration itself will fail.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we added name-based hashing the dev_base_lock was designated as the
lock to take when changing the name hash list. Unfortunately, because
it was a preexisting lock that just happened to be taken in the right
spots we neglected to take it in dev_change_name.
The race can affect calles of __dev_get_by_name that do so without taking
the RTNL. They may end up walking down the wrong hash chain and end up
missing the device that they're looking for.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes register_netdevice call dev->uninit if the regsitration
fails after dev->init has completed successfully. Very few drivers use
the init/uninit calls but at least one (drivers/net/wan/sealevel.c) may
leak without this change.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc omissions in net/:
Warning(linux-2.6.23-rc1//net/core/dev.c:2728): No description found for parameter 'addr'
Warning(linux-2.6.23-rc1//net/core/dev.c:2752): No description found for parameter 'addr'
Warning(linux-2.6.23-rc1//net/core/dev.c:3839): No description found for parameter 'net_dma'
Warning(linux-2.6.23-rc1//net/core/dev.c:3877): No description found for parameter 'state'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this two functions could share the dev->_xmit_lock acquired context.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because this function is only called by unregister_netdevice,
this moving could make this non-global function static,
and also remove its declaration in netdevice.h;
Any further, function __dev_addr_discard is also just called by
dev_mc_discard and dev_unicast_discard, keeping this two functions
both in one c file could make __dev_addr_discard also static
and remove its declaration in netdevice.h;
Futhermore, the sequential call to dev_unicast_discard and then
dev_mc_discard in unregister_netdevice have a similar mechanism that:
(netif_tx_lock_bh / __dev_addr_discard / netif_tx_unlock_bh),
they should merged into one to eliminate duplicates in acquiring and
releasing the dev->_xmit_lock, this would be done in my following patch.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add macvlan driver, which allows to create virtual ethernet devices
based on MAC address.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the set_multicast_list (and set_rx_mode) callbacks are
responsible for configuring the device according to the IFF_PROMISC,
IFF_MULTICAST and IFF_ALLMULTI flags and the mc_list (and uc_list in
case of set_rx_mode).
These callbacks can be invoked from BH context without the rtnl_mutex
by dev_mc_add/dev_mc_delete, which makes reading the device flags and
promiscous/allmulti count racy. For real hardware drivers that just
commit all changes to the hardware this is not a real problem since
the stack guarantees to call them for every change, so at least the
final call will not race and commit the correct configuration to the
hardware.
For software devices that want to synchronize promiscous and multicast
state to an underlying device however this can cause corruption of the
underlying device's flags or promisc/allmulti counts.
When the software device is concurrently put in promiscous or allmulti
mode while set_multicast_list is invoked from bottem half context, the
device might synchronize the change to the underlying device without
holding the rtnl_mutex, which races with concurrent changes to the
underlying device.
Add a dev->change_rx_flags hook that is invoked when any of the flags
that affect rx filtering change (under the rtnl_mutex), which allows
drivers to perform synchronization immediately and only synchronize
the address lists in set_multicast_list/set_rx_mode.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'ioat-md-accel-for-linus' of git://lost.foo-projects.org/~dwillia2/git/iop: (28 commits)
ioatdma: add the unisys "i/oat" pci vendor/device id
ARM: Add drivers/dma to arch/arm/Kconfig
iop3xx: surface the iop3xx DMA and AAU units to the iop-adma driver
iop13xx: surface the iop13xx adma units to the iop-adma driver
dmaengine: driver for the iop32x, iop33x, and iop13xx raid engines
md: remove raid5 compute_block and compute_parity5
md: handle_stripe5 - request io processing in raid5_run_ops
md: handle_stripe5 - add request/completion logic for async expand ops
md: handle_stripe5 - add request/completion logic for async read ops
md: handle_stripe5 - add request/completion logic for async check ops
md: handle_stripe5 - add request/completion logic for async compute ops
md: handle_stripe5 - add request/completion logic for async write ops
md: common infrastructure for running operations with raid5_run_ops
md: raid5_run_ops - run stripe operations outside sh->lock
raid5: replace custom debug PRINTKs with standard pr_debug
raid5: refactor handle_stripe5 and handle_stripe6 (v3)
async_tx: add the async_tx api
xor: make 'xor_blocks' a library routine for use with async_tx
dmaengine: make clients responsible for managing channels
dmaengine: refactor dmaengine around dma_async_tx_descriptor
...
The current implementation assumes that a channel will only be used by one
client at a time. In order to enable channel sharing the dmaengine core is
changed to a model where clients subscribe to channel-available-events.
Instead of tracking how many channels a client wants and how many it has
received the core just broadcasts the available channels and lets the
clients optionally take a reference. The core learns about the clients'
needs at dma_event_callback time.
In support of multiple operation types, clients can specify a capability
mask to only be notified of channels that satisfy a certain set of
capabilities.
Changelog:
* removed DMA_TX_ARRAY_INIT, no longer needed
* dma_client_chan_free -> dma_chan_release: switch to global reference
counting only at device unregistration time, before it was also happening
at client unregistration time
* clients now return dma_state_client to dmaengine (ack, dup, nak)
* checkpatch.pl fixes
* fixup merge with git-ioat
Cc: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
When a reference to an existing address is increased or decreased without
hitting zero, the address count is incorrectly adjusted.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the multiqueue hardware device support API to the core network
stack. Allow drivers to allocate multiple queues and manage them at
the netdev level if they choose to do so.
Added a new field to sk_buff, namely queue_mapping, for drivers to
know which tx_ring to select based on OS classification of the flow.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a boolean error in the new TX checksum check
that causes bogus TSO packets to be generated.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring secondary unicast addresses on network
devices. To support this devices capable of filtering multiple
unicast addresses need to change their set_multicast_list function
to configure unicast filters as well and assign it to dev->set_rx_mode
instead of dev->set_multicast_list. Other devices are put into promiscous
mode when secondary unicast addresses are present.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce struct dev_addr_list and list maintenance functions
based on dev_mc_list and the related functions. This will be
used by follow-up patches for both multicast and secondary
unicast addresses.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing model for checksum offload does not correctly handle
devices that can offload IPV4 and IPV6 only. The NETIF_F_HW_CSUM flag
implies device can do any arbitrary protocol.
This patch:
* adds NETIF_F_IPV6_CSUM for those devices
* fixes bnx2 and tg3 devices that need it
* add NETIF_F_IPV6_CSUM to ipv6 output (incl GSO)
* fixes assumptions about NETIF_F_ALL_CSUM in nat
* adjusts bridge union of checksumming computation
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves the local_irq_enable() call in net_rx_action() to before
calling the CONFIG_NET_DMA's dma_async_memcpy_issue_pending() rather
than after. This shortens the irq disabled window and allows for DMA
drivers that need to do their own irq hold.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing the link state from userspace not affecting any other
flags. Two duplicate notification are being sent, once as action
in the NETDEV_UP/NETDEV_DOWN notification chain and a second time
when comparing old and new device flags after the change has been
completed. Although harmless, the duplicates should be avoided.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kenji Kaneshige found this race between device removal and
registration. On unregister it is possible for the old device to
exist, because sysfs file is still open. A new device with 'eth%d'
will select the same name, but sysfs kobject register will fial.
The following changes the shutdown order slightly. It hold a removes
the sysfs entries earlier (on unregister_netdevice), but holds a
kobject reference. Then when todo runs the actual last put free
happens.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After initializing dev->_xmit_lock register_netdevice()
sets lockdep class according to dev->type.
Idea of this patch - by David Miller.
Reported & tested by: "Yuriy N. Shkandybin" <jura@netams.com>
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since nonboot CPUs are now disabled after tasks and devices have been
frozen and the CPU hotplug infrastructure is used for this purpose, we need
special CPU hotplug notifications that will help the CPU-hotplug-aware
subsystems distinguish normal CPU hotplug events from CPU hotplug events
related to a system-wide suspend or resume operation in progress. This
patch introduces such notifications and causes them to be used during
suspend and resume transitions. It also changes all of the
CPU-hotplug-aware subsystems to take these notifications into consideration
(for now they are handled in the same way as the corresponding "normal"
ones).
[oleg@tv-sign.ru: cleanups]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter P Waskiewicz Jr
Arnd Bergmann
Jiri Pirko
Krishna Kumar
David S. Miller
Jesper Dangaard Brouer
Andy Gospodarek
Eric W. Biederman
Patrick Mullaney
Joe Perches
Octavian Purdila
Jaswinder Singh Rajput
Eric Dumazet
Jarek Poplawski
Patrick McHardy
stephen hemminger
Ben Hutchings
Sridhar Samudrala
Johannes Berg
Moni Shoua
Linus Torvalds
Dmitry Eremin-Solenikov
Eric Paris
Jan Engelhardt
Ingo Molnar
Herbert Xu
Michał Mirosław
John Dykstra
Sergey Lapin
Alexander Beregalov
Neil Horman
Eric Dumazet
Marcin Slusarz
Alexander Duyck
Roel Kluin
Yi Zou
Eric W. Biederman
Patrick Ohly
Benjamin Herrenschmidt
Dan Williams
Rémi Denis-Courmont
Wang Chen
Alexey Dobriyan
James Morris
David Howells
Eric W. Biederman
Oliver Hartkopp
Arnaldo Carvalho de Melo
Joe Eykholt
Lennert Buytenhek
Ilpo Järvinen
Dave Jones
Arjan van de Ven
Jussi Kivilinna
Or Gerlitz
Carlos R. Mafra
Mike Travis
David Woodhouse
Pavel Emelyanov
Daniel Lezcano
Hirofumi Nakagawa
Alexey Dobriyan
Denis V. Lunev
YOSHIFUJI Hideaki
Linus Torvalds
Jorge Boncompte [DTI2]
Randy Dunlap
Harvey Harrison
Matti Linnanvuori
Klaus Heinrich Kiwi
Al Viro
Chris Leech
Denis Cheng
Stephen Hemminger
David S. Miller
Jeff Garzik
Jamal Hadi Salim
David S. Miller
Shannon Nelson
Thomas Graf
Jarek Poplawski
Rafael J. Wysocki