HP 6730b laptop has an ethernet NIC connected to one of the PCIe root
ports. The root ports themselves are native PCIe hotplug capable. Now,
during boot after PCI devices are scanned the BIOS triggers ACPI bus check
directly to the NIC:
ACPI: \_SB_.PCI0.RP06.NIC_: Bus check in hotplug_event()
It is not clear why it is sending bus check but regardless the ACPI hotplug
notify handler calls enable_slot() directly (instead of going through
acpiphp_check_bridge() as there is no bridge), which ends up handling
special case for non-hotplug bridges with native PCIe hotplug. This
results a crash of some kind but the reporter only sees black screen so it
is hard to figure out the exact spot and what actually happens. Based on
a few fix proposals it was tracked to crash somewhere inside
pci_assign_unassigned_bridge_resources().
In any case we should not really be in that special branch at all because
the ACPI notify happened to a slot that is not a PCI bridge (it is just a
regular PCI device).
Fix this so that we only go to that special branch if we are calling
enable_slot() for a bridge (e.g., the ACPI notification was for the
bridge).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201127
Fixes: 84c8b58ed3 ("ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug")
Reported-by: Peter Anemone <peter.anemone@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org # v4.18+
If both hot-add and power fault were observed in a single interrupt, we
handled the hot-add first, then the power fault, in this path:
pciehp_ist
if (events & (PDC | DLLSC))
pciehp_handle_presence_or_link_change
case OFF_STATE:
pciehp_enable_slot
__pciehp_enable_slot
board_added
pciehp_power_on_slot
ctrl->power_fault_detected = 0
pcie_write_cmd(ctrl, PCI_EXP_SLTCTL_PWR_ON, PCI_EXP_SLTCTL_PCC)
pciehp_green_led_on(p_slot) # power LED on
pciehp_set_attention_status(p_slot, 0) # attention LED off
if ((events & PFD) && !ctrl->power_fault_detected)
ctrl->power_fault_detected = 1
pciehp_set_attention_status(1) # attention LED on
pciehp_green_led_off(slot) # power LED off
This left the attention indicator on (even though the hot-add succeeded)
and the power indicator off (even though the slot power was on).
Fix this by checking for power faults before checking for new devices.
Prior to 0e94916e60, this was successful because everything was chained
through work queues and the order was:
INT_PRESENCE_ON -> INT_POWER_FAULT -> ENABLE_REQ
The ENABLE_REQ cleared the power fault at the end, but now everything is
handled inline with the interrupt thread, such that the work ENABLE_REQ was
doing happens before power fault handling now.
Fixes: 0e94916e60 ("PCI: pciehp: Handle events synchronously")
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
- To avoid bus errors, enable PASID only if entire path supports End-End
TLP prefixes (Sinan Kaya)
- Unify slot and bus reset functions and remove hotplug knowledge from
callers (Sinan Kaya)
- Add Function-Level Reset quirks for Intel and Samsung NVMe devices to
fix guest reboot issues (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD Controller
(Bjorn Helgaas)
* pci/virtualization:
PCI: Add function 1 DMA alias quirk for Marvell 88SS9183
PCI: Delay after FLR of Intel DC P3700 NVMe
PCI: Disable Samsung SM961/PM961 NVMe before FLR
PCI: Export pcie_has_flr()
PCI: Rename pci_try_reset_bus() to pci_reset_bus()
PCI: Deprecate pci_reset_bus() and pci_reset_slot() functions
PCI: Unify try slot and bus reset API
PCI: Hide pci_reset_bridge_secondary_bus() from drivers
IB/hfi1: Use pci_try_reset_bus() for initiating PCI Secondary Bus Reset
PCI: Handle error return from pci_reset_bridge_secondary_bus()
PCI/IOV: Tidy pci_sriov_set_totalvfs()
PCI: Enable PASID only if entire path supports End-End TLP prefixes
# Conflicts:
# drivers/pci/hotplug/pciehp_hpc.c
- Mark fall-through switch cases before enabling -Wimplicit-fallthrough
(Gustavo A. R. Silva)
- Move DMA-debug PCI init from arch code to PCI core (Christoph Hellwig)
- Fix pci_request_irq() usage of IRQF_ONESHOT when no handler is supplied
(Heiner Kallweit)
- Unify PCI and DMA direction #defines (Shunyong Yang)
- Add PCI_DEVICE_DATA() macro (Andy Shevchenko)
- Check for VPD completion before checking for timeout (Bert Kenward)
- Limit Netronome NFP5000 config space size to work around erratum (Jakub
Kicinski)
* pci/misc:
PCI: Limit config space size for Netronome NFP5000
PCI/VPD: Check for VPD access completion before checking for timeout
PCI: Add PCI_DEVICE_DATA() macro to fully describe device ID entry
PCI: Unify PCI and normal DMA direction definitions
PCI: Use IRQF_ONESHOT if pci_request_irq() called with no handler
PCI: Call dma_debug_add_bus() for pci_bus_type from PCI core
PCI: Mark fall-through switch cases before enabling -Wimplicit-fallthrough
# Conflicts:
# drivers/pci/hotplug/pciehp_ctrl.c
On driver probe and on resume from system sleep, pciehp checks the
Presence Detect State bit in the Slot Status register to bring up an
occupied slot or bring down an unoccupied slot. Both code paths are
identical, so deduplicate them per Mika's request.
On probe, an additional check is performed to disable power of an
unoccupied slot. This can e.g. happen if power was enabled by BIOS.
It cannot happen once pciehp has taken control, hence is not necessary
on resume: The Slot Control register is set to the same value that it
had on suspend by pci_restore_state(), so if the slot was occupied,
power is enabled and if it wasn't, power is disabled. Should occupancy
have changed during the system sleep transition, power is adjusted by
bringing up or down the slot per the paragraph above.
To allow for deduplication of the presence check, move the power check
to pcie_init(). This seems safer anyway, because right now it is
performed while interrupts are already enabled, and although I can't
think of a scenario where pciehp_power_off_slot() and the IRQ thread
collide, it does feel brittle.
However this means that pcie_init() may now write to the Slot Control
register before the IRQ is requested. If both the CCIE and HPIE bits
happen to be set, pcie_wait_cmd() will wait for an interrupt (instead
of polling the Command Completed bit) and eventually emit a timeout
message. Additionally, if a level-triggered INTx interrupt is used,
the user may see a spurious interrupt splat. Avoid by disabling
interrupts before disabling power. (Normally the HPIE and CCIE bits
should be clear on probe, but conceivably they may already have been
set e.g. by BIOS.)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Per Mika's request, add an explicit break to the last case of switch
statements everywhere in pciehp to be more defensive towards future
amendments.
Per Gustavo's request, mark all non-empty implicit fallthroughs with a
comment to silence warnings triggered by -Wimplicit-fallthrough=2.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
When a PCI device is detected, pdev->is_added is set to 1 and proc and
sysfs entries are created.
When the device is removed, pdev->is_added is checked for one and then
device is detached with clearing of proc and sys entries and at end,
pdev->is_added is set to 0.
is_added and is_busmaster are bit fields in pci_dev structure sharing same
memory location.
A strange issue was observed with multiple removal and rescan of a PCIe
NVMe device using sysfs commands where is_added flag was observed as zero
instead of one while removing device and proc,sys entries are not cleared.
This causes issue in later device addition with warning message
"proc_dir_entry" already registered.
Debugging revealed a race condition between the PCI core setting the
is_added bit in pci_bus_add_device() and the NVMe driver reset work-queue
setting the is_busmaster bit in pci_set_master(). As these fields are not
handled atomically, that clears the is_added bit.
Move the is_added bit to a separate private flag variable and use atomic
functions to set and retrieve the device addition state. This avoids the
race because is_added no longer shares a memory location with is_busmaster.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200283
Signed-off-by: Hari Vyas <hari.vyas@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Ensure accessibility of a hotplug port's config space when accessed via
sysfs by resuming its parent to D0.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
pciehp's IRQ thread ensures accessibility of the port by runtime resuming
its parent to D0. However when the slot is enabled/disabled, the port
itself needs to be in D0 because its secondary bus is accessed in:
pciehp_check_link_status(),
pciehp_configure_device() (both called from board_added())
and
pciehp_unconfigure_device() (called from remove_board()).
Thus, acquire a runtime PM ref on enable/disablement of the slot.
Yinghai Lu additionally discovered that some SkyLake servers feature a
Power Controller for their PCIe hotplug ports (PCIe r3.1, sec 6.7.1.8)
which requires the port to be in D0 when invoking
pciehp_power_on_slot() (likewise called from board_added()).
If slot power is turned on while in D3hot, link training later fails:
https://lkml.kernel.org/r/20170205073454.GA253@wunner.de
The spec is silent about such a requirement, but it seems prudent to
assume that any hotplug port with a Power Controller may need this.
The present commit holds a runtime PM ref whenever slot power is turned
on and off, but it doesn't keep the port in D0 as long as slot power is
on. If vendors determine that's necessary, they need to amend pciehp to
acquire a runtime PM ref in pciehp_power_on_slot() and release one in
pciehp_power_off_slot().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
If a hotplug port is able to send an interrupt, one would naively assume
that it is accessible at that moment. After all, if it wouldn't be
accessible, i.e. if its parent is in D3hot and the link to the hotplug
port is thus down, how should an interrupt come through?
It turns out that assumption is wrong at least for Thunderbolt: Even
though its parents are in D3hot, a Thunderbolt hotplug port is able to
signal interrupts. Because the port's config space is inaccessible and
resuming the parents may sleep, the hard IRQ handler has to defer
runtime resuming the parents and reading the Slot Status register to the
IRQ thread.
If the hotplug port uses a level-triggered INTx interrupt, it needs to
be masked until the IRQ thread has cleared the signaled events. For
simplicity, this commit also masks edge-triggered MSI/MSI-X interrupts.
Note that if the interrupt is shared (which can only happen for INTx),
other devices are starved from receiving interrupts until the IRQ thread
is scheduled, has runtime resumed the hotplug port's parents and has
read and cleared the Slot Status register.
That delay is dominated by the 10 ms D3hot->D0 transition time of each
parent port. The worst case is a Thunderbolt downstream port at the
end of a daisy chain: There may be up to six Thunderbolt controllers
in-between it and the root port, each comprising an upstream and
downstream port, plus its own upstream port. That's 13 x 10 = 130 ms.
Possible mitigations are polling the interrupt while it's disabled or
reducing the d3_delay of Thunderbolt ports if possible.
Open code masking of the interrupt instead of requesting it with the
IRQF_ONESHOT flag to minimize the period during which it is masked.
(IRQF_ONESHOT unmasks the IRQ only after the IRQ thread has finished.)
PCIe r4.0 sec 6.7.3.4 states that "If wake generation is required by the
associated form factor specification, a hotplug capable Downstream Port
must support generation of a wakeup event (using the PME mechanism) on
hotplug events that occur when the system is in a sleep state or the
Port is in device state D1, D2, or D3Hot."
This would seem to imply that PME needs to be enabled on the hotplug
port when it is runtime suspended. pci_enable_wake() currently doesn't
enable PME on bridges, it may be necessary to add an exemption for
hotplug bridges there. On "Light Ridge" Thunderbolt controllers, the
PME_Status bit is not set when an interrupt occurs while the hotplug
port is in D3hot, even if PME is enabled. (I've tested this on a Mac
and we hardcode the OSC_PCI_EXPRESS_PME_CONTROL bit to 0 on Macs in
negotiate_os_control(), modifying it to 1 didn't change the behavior.)
(Side note: Section 6.7.3.4 also states that "PME and Hot-Plug Event
interrupts (when both are implemented) always share the same MSI or
MSI-X vector". That would only seem to apply to Root Ports, however
the section never mentions Root Ports, only Downstream Ports. This is
explained in the definition of "Downstream Port" in the "Terms and
Acronyms" section of the PCIe Base Spec: "The Ports on a Switch that
are not the Upstream Port are Downstream Ports. All Ports on a Root
Complex are Downstream Ports.")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Upon resume from system sleep, the Slot Control register is written via:
pci_pm_resume_noirq()
pci_pm_default_resume_early()
pci_restore_state()
pci_restore_pcie_state()
PCIe r4.0, sec 6.7.3.2 says that after "issuing a write transaction that
targets any portion of the Port's Slot Control register, [...] software
must wait for [the] command to complete before issuing the next command".
pciehp currently fails to enforce that rule after the above-mentioned
write. Fix it.
(Moving restoration of the Slot Control register to pciehp doesn't seem
to make sense because the other PCIe hotplug drivers may need it as
well.)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Thunderbolt hotplug ports that were occupied before system sleep resume
with their downstream link in "off" state. Only after the Thunderbolt
controller has reestablished the PCIe tunnels does the link go up.
As a result, a spurious Presence Detect Changed and/or Data Link Layer
State Changed event occurs.
The events are not immediately acted upon because tunnel reestablishment
happens in the ->resume_noirq phase, when interrupts are still disabled.
Also, notification of events may initially be disabled in the Slot
Control register when coming out of system sleep and is reenabled in the
->resume_noirq phase through:
pci_pm_resume_noirq()
pci_pm_default_resume_early()
pci_restore_state()
pci_restore_pcie_state()
It is not guaranteed that the events are acted upon at all: PCIe r4.0,
sec 6.7.3.4 says that "a port may optionally send an MSI when there are
hot-plug events that occur while interrupt generation is disabled, and
interrupt generation is subsequently enabled." Note the "optionally".
If an MSI is sent, pciehp will gratuitously turn the slot off and back
on once the ->resume_early phase has commenced.
If an MSI is not sent, the extant, unacknowledged events in the Slot
Status register will prevent future notification of presence or link
changes.
Commit 13c65840fe ("PCI: pciehp: Clear Presence Detect and Data Link
Layer Status Changed on resume") fixed the latter by clearing the events
in the ->resume phase. Move this to the ->resume_noirq phase to also
fix the gratuitous disable/enablement of the slot.
The commit further restored the Slot Control register in the ->resume
phase, but that's dispensable because as shown above it's already been
done in the ->resume_noirq phase.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
The ->reset_slot callback introduced by commits:
2e35afaefe ("PCI: pciehp: Add reset_slot() method") and
06a8d89af5 ("PCI: pciehp: Disable link notification across slot reset")
disables notification of Presence Detect Changed and Data Link Layer
State Changed events for the duration of a secondary bus reset.
However a bus reset not only triggers these events, but may also clear
the Presence Detect State bit in the Slot Status register and the Data
Link Layer Link Active bit in the Link Status register momentarily.
According to Sinan Kaya:
"I know for a fact that bus reset clears the Data Link Layer Active bit
as soon as link goes down. It gets set again following link up.
Presence detect depends on the HW implementation. QDT root ports
don't change presence detect for instance since nobody actually
removed the card. If an implementation supports in-band presence
detect, the answer is yes. As soon as the link goes down, presence
detect bit will get cleared until recovery."
https://lkml.kernel.org/r/42e72f83-3b24-f7ef-e5bc-290fae99259a@codeaurora.org
In-band presence detect is also covered in Table 4-15 in PCIe r4.0,
sec 4.2.6.
pciehp should therefore ensure that any parts of the driver that access
those bits do not run concurrently to a bus reset. The only precaution
the commits took to that effect was to halt interrupt polling. They
made no effort to drain the slot workqueue, cancel an outstanding
Attention Button work, or block slot enable/disable requests via sysfs
and in the ->probe hook.
Now that pciehp is converted to enable/disable the slot exclusively from
the IRQ thread, the only places accessing the two above-mentioned bits
are the IRQ thread and the ->probe hook. Add locking to serialize them
with a bus reset. This obviates the need to halt interrupt polling.
Do not add locking to the ->get_adapter_status sysfs callback to afford
users unfettered access to that bit. Use an rw_semaphore in lieu of a
regular mutex to allow parallel execution of the non-reset code paths
accessing the critical bits, i.e. the IRQ thread and the ->probe hook.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rajat Jain <rajatja@google.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Sinan Kaya <okaya@kernel.org>
Per PCIe r4.0, sec 6.7.3.4, a "port may optionally send an MSI when
there are hot-plug events that occur while interrupt generation is
disabled, and interrupt generation is subsequently enabled."
On probe, we currently clear all event bits in the Slot Status register
with the notable exception of the Presence Detect Changed bit. Thereby
we seek to receive an interrupt for an already occupied slot once event
notification is enabled.
But because the interrupt is optional, users may have to specify the
pciehp_force parameter on the command line, which is inconvenient.
Moreover, now that pciehp's event handling has become resilient to
missed events, a Presence Detect Changed interrupt for a slot which is
powered on is interpreted as removal of the card. If the slot has
already been brought up by the BIOS, receiving such an interrupt on
probe causes the slot to be powered off and immediately back on, which
is likewise undesirable.
Avoid both issues by making the behavior of pciehp_force the default and
clearing the Presence Detect Changed bit on probe.
Note that the stated purpose of pciehp_force per the MODULE_PARM_DESC
("Force pciehp, even if OSHP is missing") seems nonsensical because the
OSHP control method is only relevant for SHCP slots according to the
PCI Firmware specification r3.0, sec 4.8.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
A hotplug port's Slot Status register does not count how often each type
of event occurred, it only records the fact *that* an event has occurred.
Previously pciehp queued a work item for each event. But if it missed
an event, e.g. removal of a card in-between two back-to-back insertions,
it queued up the wrong work item or no work item at all. Commit
fad214b0aa ("PCI: pciehp: Process all hotplug events before looking
for new ones") sought to improve the situation by shrinking the window
during which events may be missed.
But Stefan Roese reports unbalanced Card present and Link Up events,
suggesting that we're still missing events if they occur very rapidly.
Bjorn Helgaas responds that he considers pciehp's event handling
"baroque" and calls for its simplification and rationalization:
https://lkml.kernel.org/r/20180202192045.GA53759@bhelgaas-glaptop.roam.corp.google.com
It gets worse once a hotplug port is runtime suspended: The port can
signal an interrupt while it and its parents are in D3hot, i.e. while
it is inaccessible. By the time we've runtime resumed all parents to D0
and read the port's Slot Status register, we may have missed an arbitrary
number of events. Event handling therefore needs to be reworked to
become resilient to missed events.
Assume that a Presence Detect Changed event has occurred.
Consider the following truth table:
- Slot is in OFF_STATE and is currently empty. => Do nothing.
(The event is trailing a Link Down or we've
missed an insertion and subsequent removal.)
- Slot is in OFF_STATE and is currently occupied. => Turn the slot on.
- Slot is in ON_STATE and is currently empty. => Turn the slot off.
- Slot is in ON_STATE and is currently occupied. => Turn the slot off,
(Be cautious and assume the card in then back on.
the slot isn't the same as before.)
This leads to the following simple algorithm:
1 If the slot is in ON_STATE, turn it off unconditionally.
2 If the slot is currently occupied, turn it on.
Because those actions are now carried out synchronously, rather than by
scheduled work items, pciehp reacts to the *current* situation and
missed events no longer matter.
Data Link Layer State Changed events can be handled identically to
Presence Detect Changed events. Note that in the above truth table,
a Link Up trailing a Card present event didn't have to be accounted for:
It is filtered out by pciehp_check_link_status().
As for Attention Button Pressed events, PCIe r4.0, sec 6.7.1.5 says:
"Once the Power Indicator begins blinking, a 5-second abort interval
exists during which a second depression of the Attention Button cancels
the operation." In other words, the user can only expect the system to
react to a button press after it starts blinking. Missed button presses
that occur in-between are irrelevant.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mayurkumar Patel <mayurkumar.patel@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
When a device is hotplugged, Presence Detect and Link Up events often do
not occur simultaneously, but with a lag of a few milliseconds. Only
the first event received is relevant, the other one can be disregarded.
Moreover, Stefan Roese reports that on certain platforms, Link State and
Presence Detect may flap for up to 100 ms before stabilizing, suggesting
that such events should be disregarded for at least this long:
https://lkml.kernel.org/r/20180130084121.18653-1-sr@denx.de
On slot enablement, pciehp_check_link_status() waits for 100 ms per
PCIe r4.0, sec 6.7.3.3, then probes the hotplugged device's vendor
register for up to 1 second.
If this succeeds, the link is definitely up, so ignore any Presence
Detect or Link State events that occurred up to this point.
pciehp_check_link_status() then checks the Link Training bit in the
Link Status register. This is the final opportunity to detect
inaccessibility of the device and abort slot enablement. Any link
or presence change that occurs afterwards will cause the slot to be
disabled again immediately after attempting to enable it.
The astute reviewer may appreciate that achieving this behavior would be
more complicated had pciehp not just been converted to enable/disable
the slot exclusively from the IRQ thread: When the slot is enabled via
sysfs, each link or presence flap would otherwise cause the IRQ thread
to run and it would have to sense that those events are belonging to a
concurrent slot enablement operation and disregard them. It would be
much more difficult than this mere 3 line change.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Stefan Roese <sr@denx.de>
No callers of pciehp_enable/disable_slot() outside of pciehp_ctrl.c
remain, so declare the functions static. For now this requires forward
declarations. Those can be eliminated by reshuffling functions once the
ongoing effort to refactor the driver has settled.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously slot enablement and disablement could happen concurrently.
But now it's under the exclusive control of the IRQ thread, rendering
the locking obsolete. Drop it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Besides the IRQ thread, there are several other places in the driver
which enable or disable the slot:
- pciehp_probe() enables the slot if it's occupied and the pciehp_force
module parameter is used.
- pciehp_resume() enables or disables the slot after system sleep.
- pciehp_queue_pushbutton_work() enables or disables the slot after the
5 second delay following an Attention Button press.
- pciehp_sysfs_enable_slot() and pciehp_sysfs_disable_slot() enable or
disable the slot on sysfs write.
This requires locking and complicates pciehp's state machine.
A simplification can be achieved by enabling and disabling the slot
exclusively from the IRQ thread.
Amend the functions listed above to request slot enable/disablement from
the IRQ thread by either synthesizing a Presence Detect Changed event or,
in the case of a disable user request (via sysfs or an Attention Button
press), submitting a newly introduced force disable request. The latter
is needed because the slot shall be forced off despite being occupied.
For this force disable request, avoid colliding with Slot Status register
bits by using a bit number greater than 16.
For synchronous execution of requests (on sysfs write), wait for the
request to finish and retrieve the result. There can only ever be one
sysfs write in flight due to the locking in kernfs_fop_write(), hence
there is no risk of returning the result of a different sysfs request to
user space.
The POWERON_STATE and POWEROFF_STATE is now no longer entered by the
above-listed functions, but solely by the IRQ thread when it begins a
power transition. Afterwards, it moves to STATIC_STATE. The same
applies to canceling the Attention Button work, it likewise becomes an
IRQ thread only operation.
An immediate consequence is that the POWERON_STATE and POWEROFF_STATE is
never observed by the IRQ thread itself, only by functions called in a
different context, such as pciehp_sysfs_enable_slot(). So remove
handling of these states from pciehp_handle_button_press() and
pciehp_handle_link_change() which are exclusively called from the IRQ
thread.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
handle_button_press_event() currently determines whether the slot has
been turned on or off by looking at the Power Controller Control bit in
the Slot Control register. This assumes that an attention button
implies presence of a power controller even though that's not mandated
by the spec. Moreover the Power Controller Control bit is unreliable
when a power fault occurs (PCIe r4.0, sec 6.7.1.8). This issue has
existed since the driver was introduced in 2004.
Fix by replacing STATIC_STATE with ON_STATE and OFF_STATE and tracking
whether the slot has been turned on or off. This is also a required
ingredient to make pciehp resilient to missed events, which is the
object of an upcoming commit.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI hotplug core has just been refactored to separate slot
initialization for in-kernel use from publication to user space.
Take advantage of it in pciehp by publishing to user space last on
probe. This will allow enable/disablement of the slot exclusively from
the IRQ thread because the IRQ is requested after initialization for
in-kernel use (thereby getting its unique name needed by the IRQ thread)
but before user space is able to submit enable/disable requests.
On teardown, the order is the same in reverse: The user space interface
is removed prior to freeing the IRQ and destroying the slot.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When a hotplug driver calls pci_hp_register(), all steps necessary for
registration are carried out in one go, including creation of a kobject
and addition to sysfs. That's a problem for pciehp once it's converted
to enable/disable the slot exclusively from the IRQ thread: The thread
needs to be spawned after creation of the kobject (because it uses the
kobject's name), but before addition to sysfs (because it will handle
enable/disable requests submitted via sysfs).
pci_hp_deregister() does offer a ->release callback that's invoked
after deletion from sysfs and before destruction of the kobject. But
because pci_hp_register() doesn't offer a counterpart, hotplug drivers'
->probe and ->remove code becomes asymmetric, which is error prone
as recently discovered use-after-free bugs in pciehp's ->remove hook
have shown.
In a sense, this appears to be a case of the midlayer antipattern:
"The core thesis of the "midlayer mistake" is that midlayers are
bad and should not exist. That common functionality which it is
so tempting to put in a midlayer should instead be provided as
library routines which can [be] used, augmented, or ignored by
each bottom level driver independently. Thus every subsystem
that supports multiple implementations (or drivers) should
provide a very thin top layer which calls directly into the
bottom layer drivers, and a rich library of support code that
eases the implementation of those drivers. This library is
available to, but not forced upon, those drivers."
-- Neil Brown (2009), https://lwn.net/Articles/336262/
The presence of midlayer traits in the PCI hotplug core might be ascribed
to its age: When it was introduced in February 2002, the blessings of a
library approach might not have been well known:
https://git.kernel.org/tglx/history/c/a8a2069f432c
For comparison, the driver core does offer split functions for creating
a kobject (device_initialize()) and addition to sysfs (device_add()) as
an alternative to carrying out everything at once (device_register()).
This was introduced in October 2002:
https://git.kernel.org/tglx/history/c/8b290eb19962
The odd ->release callback in the PCI hotplug core was added in 2003:
https://git.kernel.org/tglx/history/c/69f8d663b595
Clearly, a library approach would not force every hotplug driver to
implement a ->release callback, but rather allow the driver to remove
the sysfs files, release its data structures and finally destroy the
kobject. Alternatively, a driver may choose to remove everything with
pci_hp_deregister(), then release its data structures.
To this end, offer drivers pci_hp_initialize() and pci_hp_add() as a
split-up version of pci_hp_register(). Likewise, offer pci_hp_del()
and pci_hp_destroy() as a split-up version of pci_hp_deregister().
Eliminate the ->release callback and move its code into each driver's
teardown routine.
Declare pci_hp_deregister() void, in keeping with the usual kernel
pattern that enablement can fail, but disablement cannot. It only
returned an error if the caller passed in a NULL pointer or a slot which
has never or is no longer registered or is sharing its name with another
slot. Those would be bugs, so WARN about them. Few hotplug drivers
actually checked the return value and those that did only printed a
useless error message to dmesg. Remove that.
For most drivers the conversion was straightforward since it doesn't
matter whether the code in the ->release callback is executed before or
after destruction of the kobject. But in the case of ibmphp, it was
unclear to me whether setting slot_cur->ctrl and slot_cur->bus_on to
NULL needs to happen before the kobject is destroyed, so I erred on
the side of caution and ensured that the order stays the same. Another
nontrivial case is pnv_php, I've found the list and kref logic difficult
to understand, however my impression was that it is safe to delete the
list element and drop the references until after the kobject is
destroyed.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # drivers/platform/x86
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Scott Murray <scott@spiteful.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Corentin Chary <corentin.chary@gmail.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Previously the slot workqueue was used to handle events and enable or
disable the slot. That's no longer the case as those tasks are done
synchronously in the IRQ thread. The slot workqueue is thus merely used
to handle a button press after the 5 second delay and only one such work
item may be in flight at any given time. A separate workqueue isn't
necessary for this simple task, so use the system workqueue instead.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Up until now, pciehp's IRQ handler schedules a work item for each event,
which in turn schedules a work item to enable or disable the slot. This
double indirection was necessary because sleeping wasn't allowed in the
IRQ handler.
However it is now that pciehp has been converted to threaded IRQ handling
and polling, so handle events synchronously in pciehp_ist() and remove
the work item infrastructure (with the exception of work items to handle
a button press after the 5 second delay).
For link or presence change events, move the register read to determine
the current link or presence state behind acquisition of the slot lock
to prevent it from becoming stale while the lock is contended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the attention button is pressed to power on the slot AND the user
powers on the slot via sysfs before 5 seconds have elapsed AND powering
on the slot fails because either the slot is unoccupied OR the latch is
open, we neglect turning off the green LED so it keeps on blinking.
That's because the error path of pciehp_sysfs_enable_slot() doesn't call
pciehp_green_led_off(), unlike pciehp_power_thread() which does.
The bug has been present since 2004 when the driver was introduced.
Fix by deduplicating common code in pciehp_sysfs_enable_slot() and
pciehp_power_thread() into a wrapper function pciehp_enable_slot() and
renaming the existing function to __pciehp_enable_slot(). Same for
pciehp_disable_slot(). This will also simplify the upcoming rework of
pciehp's event handling.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We've just converted pciehp to threaded IRQ handling, but still cannot
sleep in pciehp_ist() because the function is also called in poll mode,
which runs in softirq context (from a timer).
Convert poll mode to a kthread so that pciehp_ist() always runs in task
context.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
pciehp's IRQ handler queues up a work item for each event signaled by
the hardware. A more modern alternative is to let a long running
kthread service the events. The IRQ handler's sole job is then to check
whether the IRQ originated from the device in question, acknowledge its
receipt to the hardware to quiesce the interrupt and wake up the kthread.
One benefit is reduced latency to handle the IRQ, which is a necessity
for realtime environments. Another benefit is that we can make pciehp
simpler and more robust by handling events synchronously in process
context, rather than asynchronously by queueing up work items. pciehp's
usage of work items is a historic artifact, it predates the introduction
of threaded IRQ handlers by two years. (The former was introduced in
2007 with commit 5d386e1ac4 ("pciehp: Event handling rework"), the
latter in 2009 with commit 3aa551c9b4 ("genirq: add threaded interrupt
handler support").)
Convert pciehp to threaded IRQ handling by retrieving the pending events
in pciehp_isr(), saving them for later consumption by the thread handler
pciehp_ist() and clearing them in the Slot Status register.
By clearing the Slot Status (and thereby acknowledging the events) in
pciehp_isr(), we can avoid requesting the IRQ with IRQF_ONESHOT, which
would have the unpleasant side effect of starving devices sharing the
IRQ until pciehp_ist() has finished.
pciehp_isr() does not count how many times each event occurred, but
merely records the fact *that* an event occurred. If the same event
occurs a second time before pciehp_ist() is woken, that second event
will not be recorded separately, which is problematic according to
commit fad214b0aa ("PCI: pciehp: Process all hotplug events before
looking for new ones") because we may miss removal of a card in-between
two back-to-back insertions. We're about to make pciehp_ist() resilient
to missed events. The present commit regresses the driver's behavior
temporarily in order to separate the changes into reviewable chunks.
This doesn't affect regular slow-motion hotplug, only plug-unplug-plug
operations that happen in a timespan shorter than wakeup of the IRQ
thread.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Mayurkumar Patel <mayurkumar.patel@intel.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Document the driver's data structures to lower the barrier to entry for
contributors.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since commit 0f4bd8014d ("PCI: hotplug: Drop checking of PCI_BRIDGE_
CONTROL in *_unconfigure_device()"), pciehp_unconfigure_device() can no
longer fail, so declare it and its sole caller remove_board() void, in
keeping with the usual kernel pattern that enablement can fail, but
disablement cannot. No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
pciehp_disable_slot() checks if the ctrl attribute of the slot is NULL
and bails out if so. However the function is not called prior to the
attribute being set in pcie_init_slot(), and pcie_init_slot() is not
called if ctrl is NULL. So the check is unnecessary. Drop it.
It has been present ever since the driver was introduced in 2004, but it
was already unnecessary back then:
https://git.kernel.org/tglx/history/c/c16b4b14d980
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit b440bde74f ("PCI: Add pci_ignore_hotplug() to ignore hotplug
events for a device") iterates over the devices on a hotplug port's
subordinate bus in pciehp's IRQ handler without acquiring pci_bus_sem.
It is thus possible for a user to cause a crash by concurrently
manipulating the device list, e.g. by disabling slot power via sysfs
on a different CPU or by initiating a remove/rescan via sysfs.
This can't be fixed by acquiring pci_bus_sem because it may sleep.
The simplest fix is to avoid the list iteration altogether and just
check the ignore_hotplug flag on the port itself. This works because
pci_ignore_hotplug() sets the flag both on the device as well as on its
parent bridge.
We do lose the ability to print the name of the device blocking hotplug
in the debug message, but that's probably bearable.
Fixes: b440bde74f ("PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
When pciehp is unbound (e.g. on unplug of a Thunderbolt device), the
hotplug_slot struct is deregistered and thus freed before freeing the
IRQ. The IRQ handler and the work items it schedules print the slot
name referenced from the freed structure in various informational and
debug log messages, each time resulting in a quadruple dereference of
freed pointers (hotplug_slot -> pci_slot -> kobject -> name).
At best the slot name is logged as "(null)", at worst kernel memory is
exposed in logs or the driver crashes:
pciehp 0000:10:00.0:pcie204: Slot((null)): Card not present
An attacker may provoke the bug by unplugging multiple devices on a
Thunderbolt daisy chain at once. Unplugging can also be simulated by
powering down slots via sysfs. The bug is particularly easy to trigger
in poll mode.
It has been present since the driver's introduction in 2004:
https://git.kernel.org/tglx/history/c/c16b4b14d980
Fix by rearranging teardown such that the IRQ is freed first. Run the
work items queued by the IRQ handler to completion before freeing the
hotplug_slot struct by draining the work queue from the ->release_slot
callback which is invoked by pci_hp_deregister().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.4
If addition of sysfs files fails on registration of a hotplug slot, the
struct pci_slot as well as the entry in the slot_list is leaked. The
issue has been present since the hotplug core was introduced in 2002:
https://git.kernel.org/tglx/history/c/a8a2069f432c
Perhaps the idea was that even though sysfs addition fails, the slot
should still be usable. But that's not how drivers use the interface,
they abort probe if a non-zero value is returned.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.4.15+
Cc: Greg Kroah-Hartman <greg@kroah.com>
Ten years ago, commit 58319b802a ("PCI: Hotplug core: remove 'name'")
dropped the name element from struct hotplug_slot but neglected to update
the skeleton driver.
That same year, commit f46753c5e3 ("PCI: introduce pci_slot") raised the
number of arguments to pci_hp_register() from one to four.
Fourteen years ago, historic commit 7ab60fc1b8e7 ("PCI Hotplug skeleton:
final cleanups") removed all usages of the retval variable from
pcihp_skel_init() but not the variable itself, provoking a compiler
warning: https://git.kernel.org/tglx/history/c/7ab60fc1b8e7
It seems fair to assume the driver hasn't been used as a template for a new
driver in a while. Per Bjorn's and Christoph's preference, delete it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Christoph Hellwig <hch@lst.de>
Rename pci_reset_bridge_secondary_bus() to pci_bridge_secondary_bus_reset()
and move the declaration from linux/pci.h to drivers/pci.h to be used
internally in PCI directory only.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 01fd61c0b9 ("PCI: Add a return type for
pci_reset_bridge_secondary_bus()") added a return value to the function to
return if a device is accessible following a reset. Callers are not
checking the value.
Pass error code up high in the stack if device is not accessible.
Fixes: 01fd61c0b9 ("PCI: Add a return type for pci_reset_bridge_secondary_bus()")
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The shpchp driver registers for all PCI bridge devices. Its probe method
should fail if either (1) the bridge doesn't have an SHPC or (2) the OS
isn't allowed to use it (the platform firmware may be operating the SHPC
itself).
Separate these two tests into:
- A new shpc_capable() that looks for the SHPC hardware and is applicable
on all systems (ACPI and non-ACPI), and
- A simplified acpi_get_hp_hw_control_from_firmware() that we call only
when we already know an SHPC exists and there may be ACPI methods to
either request permission to use it (_OSC) or transfer control to the
OS (OSHP).
acpi_get_hp_hw_control_from_firmware() is implemented when CONFIG_ACPI=y,
but does nothing if the current platform doesn't support ACPI.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
An SHPC can be operated either by platform firmware or by the OS. The OS
uses a host bridge ACPI _OSC method to negotiate for control of SHPC. If
firmware wants to prevent an OS from operating an SHPC, it must supply an
_OSC method that declines to grant SHPC ownership to the OS.
If acpi_pci_find_root() returns NULL, it means there's no ACPI host bridge
device (PNP0A03 or PNP0A08) and hence no _OSC method, so the OS is always
allowed to manage the SHPC.
Fix a NULL pointer dereference when CONFIG_ACPI=y but the current
hardware/firmware platform doesn't support ACPI. In that case,
acpi_get_hp_hw_control_from_firmware() is implemented but
acpi_pci_find_root() returns NULL.
Fixes: 90cc0c3cc7 ("PCI: shpchp: Add shpchp_is_native()")
Link: https://lkml.kernel.org/r/20180621164715.28160-1-marc.zyngier@arm.com
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
- fix use-before-set error in ibmphp (Dan Carpenter)
- fix pciehp timeouts caused by Command Completed errata (Bjorn Helgaas)
- fix refcounting in pnv_php hotplug (Julia Lawall)
- clear pciehp Presence Detect and Data Link Layer Status Changed on
resume so we don't miss hotplug events (Mika Westerberg)
- only request pciehp control if we support it, so platform can use ACPI
hotplug otherwise (Mika Westerberg)
- convert SHPC to be builtin only (Mika Westerberg)
- request SHPC control via _OSC if we support it (Mika Westerberg)
- simplify SHPC handoff from firmware (Mika Westerberg)
* pci/hotplug:
PCI: Improve "partially hidden behind bridge" log message
PCI: Improve pci_scan_bridge() and pci_scan_bridge_extend() doc
PCI: Move resource distribution for single bridge outside loop
PCI: Account for all bridges on bus when distributing bus numbers
ACPI / hotplug / PCI: Drop unnecessary parentheses
ACPI / hotplug / PCI: Mark stale PCI devices disconnected
ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug
PCI: hotplug: Add hotplug_is_native()
PCI: shpchp: Add shpchp_is_native()
PCI: shpchp: Fix AMD POGO identification
PCI: shpchp: Use dev_printk() for OSHP-related messages
PCI: shpchp: Remove get_hp_hw_control_from_firmware() wrapper
PCI: shpchp: Remove acpi_get_hp_hw_control_from_firmware() flags
PCI: shpchp: Rely on previous _OSC results
PCI: shpchp: Request SHPC control via _OSC when adding host bridge
PCI: shpchp: Convert SHPC to be builtin only
PCI: pciehp: Make pciehp_is_native() stricter
PCI: pciehp: Rename host->native_hotplug to host->native_pcie_hotplug
PCI: pciehp: Request control of native hotplug only if supported
PCI: pciehp: Clear Presence Detect and Data Link Layer Status Changed on resume
PCI: pnv_php: Add missing of_node_put()
PCI: pciehp: Add quirk for Command Completed errata
PCI: Add Qualcomm vendor ID
PCI: ibmphp: Fix use-before-set in get_max_bus_speed()
# Conflicts:
# drivers/acpi/pci_root.c
Following PCIehp mark the unplugged PCI devices disconnected. This makes
sure PCI core code leaves the now missing hardware registers alone.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When acpiphp re-enumerates a PCI hierarchy because of an ACPI Notify()
event, we should skip bridges managed by native hotplug (pciehp or shpchp).
We don't want to scan below a native hotplug bridge until the hotplug
controller generates a hot-add event.
A typical scenario is a Root Port leading to a Thunderbolt host router that
remains powered off until something is connected to it. See [1] for the
lspci details.
1. Before something is connected, only the Root Port exists. It has
PCI_EXP_SLTCAP_HPC set and pciehp is responsible for hotplug:
00:1b.0 Root Port (HotPlug+)
2. When a USB-C or Thunderbolt device is connected, the Switch in the
Thunderbolt host router is powered up, the Root Port signals a hotplug
add event and pciehp enumerates the Switch:
01:00.0 Switch Upstream Port to [bus 02-39]
02:00.0 Switch Downstream Port to [bus 03] (HotPlug-, to NHI)
02:01.0 Switch Downstream Port to [bus 04-38] (HotPlug+, to Thunderbolt connector)
02:02.0 Switch Downstream Port to [bus 39] (HotPlug-, to xHCI)
The 02:00.0 and 02:02.0 Ports lead to Endpoints that are not powered
up yet. The Ports have PCI_EXP_SLTCAP_HPC cleared, so pciehp doesn't
handle hotplug for them and we assign minimal resources to them.
The 02:01.0 Port has PCI_EXP_SLTCAP_HPC set, so pciehp handles native
hotplug events for it.
3. The BIOS powers up the xHCI controller. If a Thunderbolt device was
connected (not just a USB-C device), it also powers up the NHI. Then
it sends an ACPI Notify() to the Root Port, and acpiphp enumerates the
new device(s):
03:00.0 Thunderbolt Host Controller (NHI) Endpoint
39:00.0 xHCI Endpoint
4. If a Thunderbolt device was connected, the host router firmware uses
the NHI to set up Thunderbolt tunnels and triggers a native hotplug
event (via 02:01.0 in this example). Then pciehp enumerates the new
Thunderbolt devices:
04:00.0 Switch Upstream Port to [bus 05-38]
05:01.0 Switch Downstream Port to [bus 06-09] (HotPlug-)
05:04.0 Switch Downstream Port to [bus 0a-38] (HotPlug+)
In this example, 05:01.0 leads to another Switch and some NICs. This
subtree is static, so 05:01.0 doesn't support hotplug and has
PCI_EXP_SLTCAP_HPC cleared.
In step 3, acpiphp previously enumerated everything below the Root Port,
including things below the 02:01.0 Port. We don't want that because pciehp
expects to manage hotplug below that Port, and firmware on the host router
may be in the middle of configuring its Link so it may not be ready yet.
To make this work better with the native PCIe (pciehp) and standard PCI
(shpchp) hotplug drivers, we let them handle all slot management and
resource allocation for hotplug bridges and restrict ACPI hotplug to
non-hotplug bridges.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=199581#c5
Link: https://lkml.kernel.org/r/20180529160155.1738-1-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: changelog, use hotplug_is_native() instead of
dev->is_hotplug_bridge]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In the same way we do for pciehp, add shpchp_is_native(), which returns
true if the bridge should be handled by the native SHPC driver. Then
convert the driver to use this function.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The fix for an AMD POGO erratum related to SHPC incorrectly identified the
device. The workaround should be applied only for AMD POGO devices, but it
was instead applied to:
- all AMD bridges, and
- all devices from any vendor with device ID 0x7458
Fixes: 53044f3574 ("[PATCH] PCI Hotplug: shpchp: AMD POGO errata fix")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use dev_printk() for messages related to requesting control of SHPC hotplug
via the OSHP method.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
get_hp_hw_control_from_firmware() is a trivial wrapper around
acpi_get_hp_hw_control_from_firmware(), probably intended to be generic in
case other firmware needed similar OS/platform negotiation.
Remove get_hp_hw_control_from_firmware() and call
acpi_get_hp_hw_control_from_firmware() directly. Add a stub for
acpi_get_hp_hw_control_from_firmware() for the non-ACPI case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_get_hp_hw_control_from_firmware() no longer uses the flags parameter,
so remove it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If _OSC exists, we evaluated it when adding the ACPI host bridge, and we
requested SHPC control if the SHPC driver is present. Use the result of
that _OSC evaluation instead of evaluating it again.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Mika Westerberg
Keith Busch
Bjorn Helgaas
Lukas Wunner
Hari Vyas
Sinan Kaya
Gustavo A. R. Silva