Pull late ARM updates from Russell King:
"Here is the late set of ARM updates for this merge window; in here is:
- The ARM parts of the broadcast timer support, core parts merged
through tglx's tree. This was left over from the previous merge to
allow the dependency on tglx's tree to be resolved.
- A fix to the VFP code which shows up on Raspberry Pi's, as well as
fixing the fallout from a previous commit in this area.
- A number of smaller fixes scattered throughout the ARM tree"
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: Fix broken commit 0cc41e4a21 corrupting kernel messages
ARM: fix scheduling while atomic warning in alignment handling code
ARM: VFP: fix emulation of second VFP instruction
ARM: 7656/1: uImage: Error out on build of multiplatform without LOADADDR
ARM: 7640/1: memory: tegra_ahb_enable_smmu() depends on TEGRA_IOMMU_SMMU
ARM: 7654/1: Preserve L_PTE_VALID in pte_modify()
ARM: 7653/2: do not scale loops_per_jiffy when using a constant delay clock
ARM: 7651/1: remove unused smp_timer_broadcast #define
Commit 0cc41e4a21 (arch: remove direct definitions of KERN_<LEVEL>
uses) is broken - not enough thought was put into changing:
.asciz "string"
to
.asciz "string1" "string2"
The problem is that each string gets _separately_ NUL terminated, so
the result is a string containing:
"string1\0string2\0"
rather than:
"string1string2\0"
With our new printk levels, this ends up as - eg, KERN_DEBUG "string":
0x01 0x00 0x07 0x00 "string" 0x00
which produces lots of \x01 in the kernel log.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This series contains changes for the Marvell EBU platforms (mvebu,
orion, kirkwood, dove) that were not part of the first set of pull
requests because of dependencies on the MMC tree, and being submitted
a little late.
Notable changes are:
* More devices get moved out of board files into device tree
descriptions. The remaining devices listed in there have patches
that will get sent for 3.10, after which we can remove a lot of the
board files entirely. We are doing the pinctrl and mmc drivers here,
ethernet and PCI still remain.
* SMP support for mvebu is improved with support for the
local interrupt controller.
* The Guruplug board file gets replaced with a DT description.
Unfortunately, the dependency on the MMC tree turned out to be a much
larger problem than expected, when the MMC maintainer rebased the patches
in his tree that all of the patches in this branch are based on, which
caused merge conflicts between the new and old versions of those patches.
To work around the merge conflicts, this branch rebases all patches
on top of the respective MMC patches that did get merged into 3.9.
The patches are all identical to the versions that were part of
linux-next, but have a new commit date.
Merge conflicts:
* in board-nsa310.c, the gpio.h inclusion was removed prematurely and
put back as a bug fix earlier. With this series it is really not needed
any more.
* The patch to add rtc support was already applied by Andrew Morton,
and conflicts with a second copy that was in this series, which adds
a lot of other devices to arch/arm/boot/dts/armada-370-xp.dtsi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7l0+
-----END PGP SIGNATURE-----
Merge tag 'late-mvebu-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC mvebu platform changes from Olof Johansson:
"This series contains changes for the Marvell EBU platforms (mvebu,
orion, kirkwood, dove) that were not part of the first set of pull
requests because of dependencies on the MMC tree, and being submitted
a little late.
Notable changes are:
- More devices get moved out of board files into device tree
descriptions. The remaining devices listed in there have patches
that will get sent for 3.10, after which we can remove a lot of the
board files entirely. We are doing the pinctrl and mmc drivers
here, ethernet and PCI still remain.
- SMP support for mvebu is improved with support for the local
interrupt controller.
- The Guruplug board file gets replaced with a DT description.
Unfortunately, the dependency on the MMC tree turned out to be a much
larger problem than expected, when the MMC maintainer rebased the
patches in his tree that all of the patches in this branch are based
on, which caused merge conflicts between the new and old versions of
those patches.
To work around the merge conflicts, this branch rebases all patches on
top of the respective MMC patches that did get merged into 3.9. The
patches are all identical to the versions that were part of
linux-next, but have a new commit date."
* tag 'late-mvebu-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (90 commits)
arm: mvebu: enable the SD card slot on Armada 370 Reference Design board
ARM: kirkwood: topkick: init mvsdio via DT
ARM: kirkwood: nsa310: convert to pinctrl
ARM: Kirkwood: topkick: Enable i2c bus.
ARM: kirkwood: topkick: convert to pinctrl
ARM: dove: convert serial DT nodes to clocks property
arm: mvebu: Add SPI flash on Armada 370 DB board
arm: mvebu: Add SPI flash on Armada XP-DB board
arm: mvebu: Add SPI flash on Armada XP-GP board
arm: mvebu: Add support for SPI controller in Armada 370/XP
clocksource: update and move armada-370-xp-timer documentation to timer directory
arm: mvebu: update DT to support local timers
ARM: Dove: convert usb host controller to DT
arm: mvebu: Enable USB controllers on Armada 370/XP boards
arm: mvebu: Add support for USB host controllers in Armada 370/XP
arm: mvebu: add button for OpenBlocks AX3-4
ARM: Kirkwood: Convert NS2 to gpio-poweroff.
ARM: Kirkwood: Convert NSA310 I2C to device tree
ARM: Kirkwood: Convert NSA310 to use gpio-poweroff driver
ARM: Kirkwood: Convert NSA310 to DT based regulators.
...
This branch contains changes for OMAP that came in late during the release
staging, close to when the merge window opened.
It contains, among other things:
- OMAP PM fixes and some patches for audio device integration
- OMAP clock fixes related to common clock conversion
- A set of patches cleaning up WFI entry and blocking.
- A set of fixes and IP block support for PM on TI AM33xx SoCs (Beaglebone, etc)
- A set of smaller fixes and cleanups around AM33xx restart and revision
detection, as well as removal of some dead code (CONFIG_32K_TIMER_HZ)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=/vBT
-----END PGP SIGNATURE-----
Merge tag 'late-omap' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late OMAP changes from Olof Johansson:
"This branch contains changes for OMAP that came in late during the
release staging, close to when the merge window opened.
It contains, among other things:
- OMAP PM fixes and some patches for audio device integration
- OMAP clock fixes related to common clock conversion
- A set of patches cleaning up WFI entry and blocking.
- A set of fixes and IP block support for PM on TI AM33xx SoCs
(Beaglebone, etc)
- A set of smaller fixes and cleanups around AM33xx restart and
revision detection, as well as removal of some dead code
(CONFIG_32K_TIMER_HZ)"
* tag 'late-omap' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: omap2: include linux/errno.h in hwmod_reset
ARM: OMAP2+: fix some omap_device_build() calls that aren't compiled by default
ARM: OMAP4: hwmod data: Enable AESS hwmod device
ARM: OMAP4: hwmod data: Update AESS data with memory bank area
ARM: OMAP4+: AESS: enable internal auto-gating during initial setup
ASoC: TI AESS: add autogating-enable function, callable from architecture code
ARM: OMAP2+: hwmod: add enable_preprogram hook
ARM: OMAP4: clock data: Add missing clkdm association for dpll_usb
ARM: OMAP2+: PM: Fix the dt return condition in pm_late_init()
ARM: OMAP2: am33xx-hwmod: Fix "register offset NULL check" bug
ARM: OMAP2+: AM33xx: hwmod: add missing HWMOD_NO_IDLEST flags
ARM: OMAP: AM33xx hwmod: Add parent-child relationship for PWM subsystem
ARM: OMAP: AM33xx hwmod: Corrects PWM subsystem HWMOD entries
ARM: DTS: AM33XX: Add nodes for OCMC RAM and WKUP-M3
ARM: OMAP2+: AM33XX: Update the hardreset API
ARM: OMAP2+: AM33XX: hwmod: Update the WKUP-M3 hwmod with reset status bit
ARM: OMAP2+: AM33XX: hwmod: Fixup cpgmac0 hwmod entry
ARM: OMAP2+: AM33XX: hwmod: Update TPTC0 hwmod with the right flags
ARM: OMAP2+: AM33XX: hwmod: Register OCMC RAM hwmod
ARM: OMAP2+: AM33XX: CM/PRM: Use __ASSEMBLER__ macros in header files
...
This branch contains of devicetree changes for the Freescale i.MX platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process since
every line of the file is touched.
On top of that are a handful of the regular changes; enabling more boards
as DT-based instead of legacy board files (mx25pdk), enabling another
driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other platforms
in the future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=72aL
-----END PGP SIGNATURE-----
Merge tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC i.MX DT changes from Olof Johansson:
"This branch contains of devicetree changes for the Freescale i.MX
platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process
since every line of the file is touched.
On top of that are a handful of the regular changes; enabling more
boards as DT-based instead of legacy board files (mx25pdk), enabling
another driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other
platforms in the future."
* tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: dts: add dtsi for imx6q and imx6dl
ARM: dts: rename imx6q.dtsi to imx6qdl.dtsi
ARM: dts: i.MX6: Add regulator delay support
ARM: dts: Add device tree entry for onewire master on i.MX53
ARM: i.MX53: Add clocks for i.mx53 onewire master.
W1: Add device tree support to MXC onewire master.
ARM: imx: enable imx6q-cpufreq support
ARM: dts: Add apf51 basic support
ARM i.MX6: change mxs usbphy clock usage
ARM: dts: imx6q: Remove silicon version from SDMA firmware
ARM i.MX53: dts: add oftree for MBa53 baseboard
ARM i.MX53: add dts for the TQ tqma53 module
ARM: dts: imx53: pinctrl update
ARM i.MX51 babbage: Add keypad support
ARM: dts: imx: Add imx51 KPP entry
ARM: dts: imx25-karo-tx25: Put status entry in the end
ARM: mx25pdk: Add device tree support
ARM: dts: imx: use nodes label in board dts
ARM: dts: add missing imx dtb targets
ARM: boot: dts: Add an entry for imx27-pdk.dtb
...
The Armada 370 Reference Design board has one SD card slot, directly
connected to the SDIO IP of the SoC, so we enable this IP. there are no
GPIOs for card-detect and write-protect so we do not specify any.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
of_serial now has support for using clocks property and we have
a DT clock provider. This patch replaces the hard coded clock-frequency
property with a clocks phandle to tclk.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch add support for the SPI flash MX25l25635E which is present
on the Armada 370 DB board. This flash stores the bootloader and its
environment.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch add support for the SPI flash M25P64 which is present on
the Armada XP DB board. This flash stores the bootloader and its
environment.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds an SPI master device node for Armada XP-GP board.
This master node is an SPI flash controller 'n25q128a13'.
Since there is no 'partitions' node declared, one full sized
partition named as the device will be created.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Tested-by: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 370 and Armada XP SoC has an SPI controller.
This patch adds support for this controller in Armada 370
and Armada XP SoC common device tree files.
Note that the Armada XP SPI register length is 0x50 bytes,
while Armada 370 SPI register length is 0x28 bytes,
so we choose the smaller of the two.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Acked-by: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the time-armada-370-xp support local timers, updated the
device tree to take it into account.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With DT support for orion-ehci also convert Dove to it and
remove the legacy calls and clock aliases.
This patch is based on "ARM: Dove: split legacy and DT setup"
applied to mvebu/boards recently.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch activates every USB port provided by each SoC.
Except for Armada XP Openblocks AX3-4 board,
where we enable only the first two USB ports
until we have more information on the third one usage.
Cc: Lior Amsalem <alior@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 370 and Armada XP SoC has an Orion EHCI USB controller.
This patch adds support for this controller in Armada 370
and Armada XP SoC common device tree files.
Cc: Lior Amsalem <alior@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The OpenBlocks AX3-4 board has one software-controlled button on the
front side, labeled "INIT", so we add minimal support for this button
in the kernel.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Remove C code and add a Device Tree node in its place.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add a sub-node into the I2C node to represent the adt7476 device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Remove the C code and add a Device Tree node for gpio-poweroff.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
CuBox needs to enable USB power on a gpio pin. Add a fixed regulator
to always enable usb power on boot.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
gpio-leds has support for pinctrl allocation, make use of it.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The 88f6282 has one more TWSI(TWSI1). This add the information to enable
pinctl of TWSI1.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds a pinmux option, pmx_sdio, to enable the muxing of
the SDIO interface on the 88F6282 SoC from Marvell.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the mvsdio driver has a Device Tree binding, and the SDIO
controller is declared in kirkwood.dtsi, migrate the mplcec4 board to
use the Device Tree to probe the SDIO controller and to mux the pins
of the SDIO interface correctly.
This patch has not been tested, it remains to be tested by a person
having access to the hardware.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Stefan Peter <s.peter@mpl.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the mvsdio driver has a Device Tree binding, and the SDIO
controller is declared in kirkwood.dtsi, migrate the dreamplug board
to use the Device Tree to probe the SDIO controller and to mux this
interface properly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the SDIO controller has a Device Tree binding, let's use it
in kirkwood.dtsi.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Globalscale Mirabox uses the SDIO interface of the Armada 370 to
connect to a Wifi/Bluetooth SD8787 chip, so we enable the SDIO
interface of this board in its Device Tree file.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP DB evaluation board has one SD card slot, directly
connected to the SDIO IP of the SoC, so we add a device tree
description for it.
However, in the default configuration of the board, the SD card slot
is not usable: the connector plugged into CON40 must be changed
against a different one, provided with the board by the
manufacturer. Since such a manual modification of the hardware is
needed, we did not enable the SDIO interface by default, and left it
to the board user to modify the Device Tree if needed. Since this
board is really only an evaluation board for developers and not a
final product, it is not too bad.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP DB evaluation board has one SD card slot, directly
connected to the SDIO IP of the SoC, so we enable this
IP. Unfortunately, there are no GPIOs for card-detect and
write-protect.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The SDIO interface is only available on pins MPP30/31/32/33/34/35 on
the various Armada XP variants, so we provide a pin muxing option for
this in the Armada XP .dtsi files.
Even though those muxing options are the same for MV78230, MV78260 and
MV78460, we keep them in each .dtsi file, because the number of pins,
and therefore the declaration of the pinctrl node, is different for
each SoC variant.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The SDIO interface is available either on pins MPP9/11/12/13/14/15 or
MPP47/48/49/50/51/52 on the Armada 370. Even though all combinations
are potentially possible, those two muxing options are the most
probable ones, so we provide those at the SoC level .dtsi file.
In practice, in turns out the Armada 370 DB board uses the former,
while the Armada 370 Mirabox uses the latter.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the mvsdio MMC driver has a Device Tree binding, we add the
Device Tree informations to describe the SDIO interface available in
the Armada 370/XP SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 370 and Armada XP Socs have the same controller that the
one used in the orion platforms. This patch updates the device tree
for these SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Some of the mvebu boards (mainly the development board) come with
plug-in RAM modules. This patch allows to let the bootloaders which
have no support for DTS to give the real amount of memory available on
the board.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP DB-MV784MP-GP board has an SPI flash device.
These options allow to access that device over MTD.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is the new Armada XP evaluation board from Marvell. It comes with
a RS232 port over USB, a SATA link, an internal SSD, 4 Ethernet
Gigabit links.
Support for USB (Host and device), SDIO, PCIe will be added as drivers
when they become available for Armada XP in mainline.
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that we have support for local timers, enable it by default
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
MPIC allows the use of private interrupt for each CPUs. The 28th first
interrupts are per-cpu. This patch adds support to use them.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add a device tree entry for the Guruplug Server Plus board. This port
was based both on the work done on the dreamplug and the dockstar.
It builds, boots and works on my Guruplug Server Plus.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds the DTS file to support the Marvell RD-A370-A1
(Reference Design board) also known as RD-88F6710 board. It is almost
entirely similar to the DB-A370 board except that the first Ethernet PHY
is SGMII-wired and the second is a switch which is RGMII-wired.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Linus Torvalds
Russell King
Florian Fainelli
Jason Cooper
Andrew Lunn
Sebastian Hesselbarth
Gregory CLEMENT
Ezequiel Garcia
Thomas Petazzoni
Nobuhiro Iwamatsu
Willy Tarreau