cycle:
Core changes:
- Device links can optionally be added between a pin control
producer and its consumers. This will affect how the system
power management is handled: a pin controller will not suspend
before all of its consumers have been suspended. This was
necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense
to make this default in the long run. Right now it is
opt-in per driver.
- Drive strength can be specified in microamps. With decreases
in silicon technology, milliamps isn't granular enough, let's
make it possible to select drive strengths in microamps. Right
now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a
product line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in
addition to muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken
aside and not usable for users. This is used in ACPI systems
to take out some GPIO lines used by the BIOS so that
noone else (neither kernel nor userspace) will play with them
by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board
management controllers for servers) in preparation for the
new Aspeed AST2600 SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=Wdw1
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.3 kernel cycle:
Core changes:
- Device links can optionally be added between a pin control producer
and its consumers. This will affect how the system power management
is handled: a pin controller will not suspend before all of its
consumers have been suspended.
This was necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense to make
this default in the long run.
Right now it is opt-in per driver.
- Drive strength can be specified in microamps. With decreases in
silicon technology, milliamps isn't granular enough, let's make it
possible to select drive strengths in microamps.
Right now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a product
line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in addition to
muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken aside and
not usable for users. This is used in ACPI systems to take out some
GPIO lines used by the BIOS so that noone else (neither kernel nor
userspace) will play with them by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board management
controllers for servers) in preparation for the new Aspeed AST2600
SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes"
* tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits)
pinctrl: aspeed: Strip moved macros and structs from private header
pinctrl: aspeed: Fix missed include
pinctrl: baytrail: Use GENMASK() consistently
pinctrl: baytrail: Re-use data structures from pinctrl-intel.h
pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux()
pinctrl: qcom: Add SM8150 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding
dt-bindings: pinctrl: qcom: Document missing gpio nodes
pinctrl: aspeed: Add implementation-related documentation
pinctrl: aspeed: Split out pinmux from general pinctrl
pinctrl: aspeed: Clarify comment about strapping W1C
pinctrl: aspeed: Correct comment that is no longer true
MAINTAINERS: Add entry for ASPEED pinctrl drivers
dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema
dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema
dt-bindings: pinctrl: aspeed: Split bindings document in two
pinctrl: qcom: Add irq_enable callback for msm gpio
pinctrl: madera: Fixup SPDX headers
pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard
pinctrl: tegra: Add bitmask support for parked bits
...
During suspend/resume, mtk_eint_mask may be called while
wake_mask is active. For example, this happens if a wake-source
with an active interrupt handler wakes the system:
irq/pm.c:irq_pm_check_wakeup would disable the interrupt, so
that it can be handled later on in the resume flow.
However, this may happen before mtk_eint_do_resume is called:
in this case, wake_mask is loaded, and cur_mask is restored
from an older copy, re-enabling the interrupt, and causing
an interrupt storm (especially for level interrupts).
Step by step, for a line that has both wake and interrupt enabled:
1. cur_mask[irq] = 1; wake_mask[irq] = 1; EINT_EN[irq] = 1 (interrupt
enabled at hardware level)
2. System suspends, resumes due to that line (at this stage EINT_EN
== wake_mask)
3. irq_pm_check_wakeup is called, and disables the interrupt =>
EINT_EN[irq] = 0, but we still have cur_mask[irq] = 1
4. mtk_eint_do_resume is called, and restores EINT_EN = cur_mask, so
it reenables EINT_EN[irq] = 1 => interrupt storm as the driver
is not yet ready to handle the interrupt.
This patch fixes the issue in step 3, by recording all mask/unmask
changes in cur_mask. This also avoids the need to read the current
mask in eint_do_suspend, and we can remove mtk_eint_chip_read_mask
function.
The interrupt will be re-enabled properly later on, sometimes after
mtk_eint_do_resume, when the driver is ready to handle it.
Fixes: 58a5e1b64b ("pinctrl: mediatek: Implement wake handler and suspend resume")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Before suspending, mtk-eint would set the interrupt mask to the
one in wake_mask. However, some of these interrupts may not have a
corresponding interrupt handler, or the interrupt may be disabled.
On resume, the eint irq handler would trigger nevertheless,
and irq/pm.c:irq_pm_check_wakeup would be called, which would
try to call irq_disable. However, if the interrupt is not enabled
(irqd_irq_disabled(&desc->irq_data) is true), the call does nothing,
and the interrupt is left enabled in the eint driver.
Especially for level-sensitive interrupts, this will lead to an
interrupt storm on resume.
If we detect that an interrupt is only in wake_mask, but not in
cur_mask, we can just mask it out immediately (as mtk_eint_resume
would do anyway at a later stage in the resume sequence, when
restoring cur_mask).
Fixes: bf22ff45be ("genirq: Avoid unnecessary low level irq function calls")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting this up will configure wake from suspend properly,
and wake only for the interrupts that are setup in wake_mask,
not all interrupts.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl variants that include pinctrl-paris.h (and not
pinctrl-mtk-common.h) also need to use pm_ops to setup
wake mask properly, so copy over the pm_ops from common
to paris variant.
It is not easy to merge the 2 copies (or move
mtk_eint_suspend/resume to mtk-eint.c), as we need to
dereference pctrl->eint, and struct mtk_pinctrl *pctl has a
different structure definition for v1 and v2 (which is
what paris variant uses).
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds the pinctrl driver for the MediaTek's MT8516 SoC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch provides the advanced drive for I2C used pins on MT8183.
The detail strength specification description of the I2C pin:
When E1=0/E0=0, the strength is 0.125mA.
When E1=0/E0=1, the strength is 0.25mA.
When E1=1/E0=0, the strength is 0.5mA.
When E1=1/E0=1, the strength is 1mA.
For I2C pins, there are existing generic driving setup and the above
specific driving setup. I2C pins can only support 2/4/6/8/10/12/14/16mA
driving adjustment in generic driving setup. But in specific driving
setup, they can support 0.125/0.25/0.5/1mA adjustment.
If we enable specific driving setup for I2C pins,
the existing generic driving setup will be disabled.
For some special features, we need the I2C pins specific driving setup.
The specific driving setup is controlled by E1E0EN.
So we need add extra vendor driving preperty instead of the generic
driving property. We can add "mediatek,drive-strength-adv = <XXX>;"
to describe the specific driving setup property.
"XXX" means the value of E1E0EN. So the valid arguments of
"mediatek,drive-strength-adv" are from 0 to 7.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
on i386 or x86_64:
Lots of build errors for drivers/pinctrl/mediatek/pinctrl-moore.c when
CONFIG_OF is not enabled (but COMPILE_TEST is).
first this:
WARNING: unmet direct dependencies detected for PINCTRL_MTK_MOORE
Depends on [n]: PINCTRL [=y] && (ARCH_MEDIATEK || COMPILE_TEST [=y])
&& OF [=n]
Selected by [y]:
- PINCTRL_MT7623 [=y] && PINCTRL [=y] &&
(ARCH_MEDIATEK || COMPILE_TEST [=y]) && (MACH_MT7623 || COMPILE_TEST [=y])
and then:
../drivers/pinctrl/mediatek/pinctrl-moore.c:22:44: error: array type has
incomplete element type
static const struct pinconf_generic_params mtk_custom_bindings[] = {
(etc)
Fixes: b5af33df50 ("pinctrl: mediatek: improve Kconfig dependencies")
Cc: stable@vger.kernel.org
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Virtual gpio only used inside SOC and not being exported to outside SOC.
Some modules use virtual gpio as eint and doesn't need SMT.
So this patch add EINT support to virtual GPIOs.
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove prompts to make all pinctrl cores to non-visible symbols and
make sure the target SoCs would be coupled with the corresponding
cores.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com
Acked-by: Sean Wang <sean.wang@kernel.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-mediatek@lists.infradead.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds MT7629 pinctrl driver based on MediaTek pinctrl-moore core.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Trivial fix to clean up indentation issues, add one level of
indentation on two if statements.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For SoC's which lacks EINT support, U16_MAX is assigned to both eint_m
and eint_n through macro NO_EINT_SUPPORT. This will generate integer
overflow warning because eint_m is declared as u8 type. Hence modify
the eint_m type to u16.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Removing the linux/gpio.h include means we no longer have a declaration
of gpiochip_lock_as_irq() when CONFIG_GPIOLIB is disabled:
drivers/pinctrl/mediatek/mtk-eint.c: In function 'mtk_eint_irq_request_resources':
drivers/pinctrl/mediatek/mtk-eint.c:247:8: error: implicit declaration of function 'gpiochip_lock_as_irq'; did you mean 'spin_lock_irq'? [-Werror=implicit-function-declaration]
drivers/pinctrl/mediatek/mtk-eint.c: In function 'mtk_eint_irq_release_resources':
drivers/pinctrl/mediatek/mtk-eint.c:272:2: error: implicit declaration of function 'gpiochip_unlock_as_irq'; did you mean 'spin_unlock_irq'? [-Werror=implicit-function-declaration]
Select it explictly instead.
Fixes: 1c5fb66afa ("pinctrl: Include <linux/gpio/driver.h> nothing else")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mtk_eint_set_debounce and mtk_eint_find_irq are defined as stub functions
in a header file, but without marking them as 'static inline', we get
a copy for each file that includes the header:
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.o: In function `mtk_eint_set_debounce':
pinctrl-mtk-common-v2.c:(.text+0x134): multiple definition of `mtk_eint_set_debounce'
drivers/pinctrl/mediatek/pinctrl-moore.o:pinctrl-moore.c:(.text+0x7d0): first defined here
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.o: In function `mtk_eint_find_irq':
pinctrl-mtk-common-v2.c:(.text+0x13c): multiple definition of `mtk_eint_find_irq'
Fixes: e46df235b4 ("pinctrl: mediatek: refactor EINT related code for all MediaTek pinctrl can fit")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, the check on desc->eint.eint_n == EINT_NA is always false
because this is comparing a u16 to -1 which can never be true. Fix
this by casting EINT_NA to u16.
Detected by CoverityScan, CID#1473610 ("Operands don't affect result")
Fixes: fb5fa8dc15 ("pinctrl: mediatek: extend struct mtk_pin_desc to pinctrl-mtk-common-v2.c")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Just add eint support to MT6765 pinctrl driver as usual as
happens on the other SoCs.
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add MT6765 pinctrl driver based on MediaTek pinctrl-paris core.
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: ZH Chen <zh.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add NO_EINT_SUPPORT back to pinctrl-mtk-common-v2.h as the alias of
EINT_NA to indicate that some pin not capable of being controlled as eint
and that is required by pinctrl-paris based driver as old
pinctrl-mtk-common.h already had.
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case of error, the function devm_kmalloc_array() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: b7d7f9eeca ("pinctrl: mediatek: extend struct mtk_pin_desc which per-pin driver depends on")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes the following sparse warning:
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c:37:29: warning:
symbol 'mtk_drive' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case of error, the function devm_kmalloc_array() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 805250982b ("pinctrl: mediatek: add pinctrl-paris that implements the vendor dt-bindings")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Include only <linux/gpio/driver.h> since this is a driver,
not a consumer.
Cc: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Just add eint support to MT8183 pinctrl driver as usual as
happens on the other SoCs.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Almost all MediaTek SoCs apply the exact same logic to build eint, so move
the common functions into pinctrl-mtk-common-v2.c to allow each new pinctrl
driver to reuse them. Also, add a protection checker on hw->soc->eint_hw to
avoid invalid memory access when there's certain SoC not to define its
eint_hw properly in the code flow.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch provides the advanced pull for I2C used pins on MT8183.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Extend the advanced pull based on the legacy bias plus additional r0 and r1
to tweak the resistor level.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add MT8183 pinctrl driver based on MediaTek pinctrl-paris core.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl-paris core that implements vendor dt-binding which MediaTek
tablet, box and smartphone-based SoCs such as MT81xx, MT27xx, and MT67xx
SoCs really want to depend on. The driver is just completely rewritten
according to pinctrl-mtk-common.c but uses the new logic from
pinctrl-mtk-common-v2.c to have an elegant way to support new SoCs in the
future.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Because the pincrl-mtk-common.c is an implementation for per-pin binding,
its pin descriptor includes more information than pinctrl-mtk-common-v2
so far can support. So, we complement these data before writing a driver
using pincrl-mtk-common-v2.c for per-pin binding. By the way, the size of
struct mtk_pin_desc would be larger than struct pinctrl_pin_desc can hold,
so it's necessary to have a copy before the pins information is being
registered into the core.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's usual and not an error for there's some register not supported by a
certain SoC or a pin so that in the case we have to adjust the message to
print and the error code to get rid of unnecessary false alarm.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Certain SoC own multiple register base for accessing each pin groups,
it's easy to be done with extend struct mtk_pin_field_calc to support
the kind of SoC such as MT8183.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
all use pin descriptor instead in pinctrl-mtk-common-v2.c for the
consistency and extensibility.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adding MT7623 pinctrl driver based on generic pinctrl binding, that is
good example and demonstrates how to port any other MediaTek SoCs
pinctrl-moore core when people really would like to use the generic
pinctrl binding to support these MediaTek SoCs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Certain SoCs have to program an extra PULLEN, PULLSEL register to configure
bias related function so that we add it in the existing path.
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Certain SoCs have to program an extra IES register to configure input
enabled mode so that we add it in the existing path as an option.
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are some specific pins (i.e. MMC/SD) need specific registers to
turn on/off the 10K & 50k(75K) resistors when pull up/down.
Therefore, this patch adds the custom prarmeters so that the user could
control it through device tree.
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Put pull control support related functions to pinctrl-mtk-common-v2.c
as these operations might be different by chips and allow different
type of driver to reuse them.
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Certain SoCs have to program DRV register to configure driving
strength so that we add it in the existing path as an option.
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Put driving strength support related functions to pinctrl-mtk-common-v2.c
as these operations might be different by chips and allow different type
of driver to reuse them.
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add two parameters gpio_m and eint_m for configuring GPIO mode and EINT
mode, they might be varying depend on SoC.
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch introduces a data structure mtk_pin_desc, which is used to
provide information per pin characteristic such as driving current,
eint number and a driving index, that is used to lookup table describing
the details about the groups of driving current by which the pin is able
to adjust the driving strength so that the driver could get the
appropriate driving group when calls .pin_config_get()/set().
Signed-off-by: Ryder.Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Torvalds
Nicolas Boichat
Thomas Gleixner
Fabien Parent
Zhiyong Tao
Linus Walleij
Ryder Lee
chuanjia.liu
Rob Herring
Manivannan Sadhasivam
Olof Johansson
Colin Ian King
Arnd Bergmann
Mars Cheng
ZH Chen
Sean Wang
Wei Yongjun