cycle:
Core changes:
- Device links can optionally be added between a pin control
producer and its consumers. This will affect how the system
power management is handled: a pin controller will not suspend
before all of its consumers have been suspended. This was
necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense
to make this default in the long run. Right now it is
opt-in per driver.
- Drive strength can be specified in microamps. With decreases
in silicon technology, milliamps isn't granular enough, let's
make it possible to select drive strengths in microamps. Right
now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a
product line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in
addition to muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken
aside and not usable for users. This is used in ACPI systems
to take out some GPIO lines used by the BIOS so that
noone else (neither kernel nor userspace) will play with them
by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board
management controllers for servers) in preparation for the
new Aspeed AST2600 SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=Wdw1
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.3 kernel cycle:
Core changes:
- Device links can optionally be added between a pin control producer
and its consumers. This will affect how the system power management
is handled: a pin controller will not suspend before all of its
consumers have been suspended.
This was necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense to make
this default in the long run.
Right now it is opt-in per driver.
- Drive strength can be specified in microamps. With decreases in
silicon technology, milliamps isn't granular enough, let's make it
possible to select drive strengths in microamps.
Right now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a product
line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in addition to
muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken aside and
not usable for users. This is used in ACPI systems to take out some
GPIO lines used by the BIOS so that noone else (neither kernel nor
userspace) will play with them by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board management
controllers for servers) in preparation for the new Aspeed AST2600
SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes"
* tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits)
pinctrl: aspeed: Strip moved macros and structs from private header
pinctrl: aspeed: Fix missed include
pinctrl: baytrail: Use GENMASK() consistently
pinctrl: baytrail: Re-use data structures from pinctrl-intel.h
pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux()
pinctrl: qcom: Add SM8150 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding
dt-bindings: pinctrl: qcom: Document missing gpio nodes
pinctrl: aspeed: Add implementation-related documentation
pinctrl: aspeed: Split out pinmux from general pinctrl
pinctrl: aspeed: Clarify comment about strapping W1C
pinctrl: aspeed: Correct comment that is no longer true
MAINTAINERS: Add entry for ASPEED pinctrl drivers
dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema
dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema
dt-bindings: pinctrl: aspeed: Split bindings document in two
pinctrl: qcom: Add irq_enable callback for msm gpio
pinctrl: madera: Fixup SPDX headers
pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard
pinctrl: tegra: Add bitmask support for parked bits
...
Now all Renesas pin control drivers have been converted to use the new
non-GPIO helper macros, SH_PFC_PIN_NAMED() and SH_PFC_PIN_NAMED_CFG()
are no longer used. Remove them.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the SH-Mobile AG5 pin control driver to use the new macros for
describing pins without GPIO functionality. This replaces the use of
physical pin numbers on the SH-Mobile AG5 SoC (in 34x34 BGA package) by
symbolic enum values, referring to signal names.
Note that the user-visible names of these pins are still based on pin
numbers instead of signal names, to preserve DT backwards compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the R-Car E3 pin control driver to use the new macros for
describing pins without GPIO functionality. This replaces the use of
physical pin numbers on the R-Car E3 SoC (in 25x25 FCBGA package) by
symbolic enum values, referring to signal names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the R-Car M3-N pin control driver to use the new macros for
describing pins without GPIO functionality. This replaces the use of
physical pin numbers on the R-Car M3-N SiP (in 39x39 BGA package) by
symbolic enum values, referring to signal names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the R-Car M3-W pin control driver to use the new macros for
describing pins without GPIO functionality. This replaces the use of
physical pin numbers on the R-Car M3-W SiP (in 39x39 BGA package) by
symbolic enum values, referring to signal names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the R-Car H3 ES2.0 and later pin control driver to use the new
macros for describing pins without GPIO functionality. This replaces
the use of physical pin numbers on the R-Car H3 ES2.0 SiP (in 39x39
BGA package) by symbolic enum values, referring to signal names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the R-Car H3 ES1.x pin control driver to use the new macros for
describing pins without GPIO functionality. This replaces the use of
physical pin numbers on the R-Car H3 ES1.x SiP (in 39x39 BGA package) by
symbolic enum values, referring to signal names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the R-Car H2 pin control driver to use the new macros for
describing pins without GPIO functionality. This replaces the use of
physical pin numbers on the R-Car H2 SoC (in 31x31 FCBGA package) by
symbolic enum values, referring to signal names.
Note that the user-visible names of these pins are still based on pin
numbers instead of signal names, to preserve DT backwards compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the R-Car M1A pin control driver to use the new macros for
describing pins without GPIO functionality. This replaces the use of
physical pin numbers on the R-Car M1A SoC (in 25x25 FCBGA package) by
symbolic enum values, referring to signal names.
Note that the user-visible names of these pins are still based on pin
numbers instead of signal names, to preserve DT backwards compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the EMMA Mobile EV2 pin control driver to use the new macros for
describing pins without GPIO functionality. This replaces the use of
physical pin numbers on the EMMA Mobile EV2 SoC (in 23x23 BGA package)
by symbolic enum values, referring to signal names.
Note that the user-visible names of these pins are still based on pin
numbers instead of signal names, to preserve DT backwards compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Add new macros for describing pins without GPIO functionality:
- NOGP_ALL() expands to a list of PIN_id values, to be used for
generating symbolic enum values,
- PINMUX_NOGP_ALL() expands to a list of sh_pfc_pin entries, to
list all pins and their capabilities.
Both macros depend on an SoC-specific CPU_ALL_NOGP() macro, to be
provided by each individual SoC pin control driver.
The new macros offer two advantages over the existing SH_PFC_PIN_NAMED()
and SH_PFC_PIN_NAMED_CFG() macros:
1. They do not rely on PIN_NUMBER() macros and physical pin numbering,
hence do not suffer from pin numbering confusion among different
SoC/SiP packages.
2. They are similar in spirit to the existing scheme for handling pins
with GPIO functionality.
Note that internal to the driver, non-GPIO pins use a sequential
numbering scheme which starts after the highest GPIO pin number in use.
This value is calculated automatically, using two new helper macros, for
systems with either 32-port bank (GP port style) or linear (PORT style)
pin space. Sample expansion:
GP_LAST = sizeof(union {
char dummy[0] __attribute__((deprecated, deprecated));
char GP_0_0[(0 * 32) + 0] __attribute__((deprecated, deprecated));
char GP_0_1[(0 * 32) + 1] __attribute__((deprecated, deprecated));
...
char GP_7_3[(7 * 32) + 3] __attribute__((deprecated, deprecated));
})
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Prior to the adoption of SPDX, it was difficult for tools to determine
the correct license due to incomplete or badly formatted license text.
The SPDX solves this issue, assuming people can correctly spell
"SPDX-License-Identifier" although this assumption is broken in some
places.
Since scripts/spdxcheck.py parses only lines that exactly matches to
the correct tag, it cannot (should not) detect this kind of error.
If the correct tag is missing, scripts/checkpatch.pl warns like this:
WARNING: Missing or malformed SPDX-License-Identifier tag in line *
So, people should notice it before the patch submission, but in reality
broken tags sometimes slip in. The checkpatch warning is not useful for
checking the committed files globally since large number of files still
have no SPDX tag.
Also, I am not sure about the legal effect when the SPDX tag is broken.
Anyway, these typos are absolutely worth fixing. It is pretty easy to
find suspicious lines by grep.
$ git grep --not -e SPDX-License-Identifier --and -e SPDX- -- \
:^LICENSES :^scripts/spdxcheck.py :^*/license-rules.rst
arch/arm/kernel/bugs.c:// SPDX-Identifier: GPL-2.0
drivers/phy/st/phy-stm32-usbphyc.c:// SPDX-Licence-Identifier: GPL-2.0
drivers/pinctrl/sh-pfc/pfc-r8a77980.c:// SPDX-Lincense-Identifier: GPL 2.0
lib/test_stackinit.c:// SPDX-Licenses: GPLv2
sound/soc/codecs/max9759.c:// SPDX-Licence-Identifier: GPL-2.0
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of the custom PORT_GP_PUP_27() macro by using the common
PORT_GP_CFG_27() macro instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This follows the style of the existing PORT_GP_X macros, and will be
used by a follow-up patch for the r8a7778 SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add pins, groups and functions for the 16-Bit Timer Pulse Unit outputs
on the R-Car M3-N SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add pins, groups and functions for the 16-Bit Timer Pulse Unit outputs
on the R-Car M3-W and RZ/G2M SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add pins, groups and functions for the 16-Bit Timer Pulse Unit outputs
on revisions ES2.x and later of the R-Car H3 SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add pins, groups and functions for the 16-Bit Timer Pulse Unit outputs
on revision ES1.x of the R-Car H3 SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Hardware Manual Errata for rev. 1.50 of March 26, 2019 removed the bit
definitions for MMC_CD and MMC_WP in the documentation for the IPSR6 and
IPSR7 registers, as these pin functionalities do not exist on R-Car
V3M.
Remove the definitions, and the corrresponding pins and groups.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Several drivers have identical definitions for PIN_NONE.
Provide a definition with a SH_PFC_ prefix for general use in sh_pfc.h,
and convert all drivers over to use it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
It is very common for a pin to support both pull-up and pull-down
functionality. Hence add a shorthand SH_PFC_PIN_CFG_PULL_UP_DOWN.
This not only reduces typing, but also avoids the need for several line
breaks, and makes many overly long lines shorter, improving
readability.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
There are two variants of the CPU_ALL_PORT() macro in use:
1. A three-parameter variant, to be provided for SoCs with a linear
GPIO pin space ("PORT style"),
2. A two-parameter variant, to be provided for SoCs with 32-port GPIO
banks ("GP port style").
Rename the 2-parameter variant to CPU_ALL_GP(), to avoid confusion, and
to increase naming consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Extend the run-time debug code with checks to ensure there are no
conflicting pin names, numbers, or enumeration values.
This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The pinmux groups and functions arrays may contain two parts, to ease
supporting SoCs that expose pin subsets of other related SoCs. Both
parts need to be declared with explicit sizes, which thus need to be
updated when adding support for more groups and functions.
If a size is too small, the compiler will detect this at build time
("excess elements in array initializer").
If a size is too large, this may go undetected (for pin groups), lead to
pin controller registration failures (for pin functions: "pinmux ops has
no name for functionN"), or crash the optional run-time debug code (for
pin groups).
Extend the run-time debug code with checks to detect this, to help
catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
All run-time debug code is called from sh_pfc_init(), which is __init.
Fixes: 6161b39a14 ("pinctrl: sh-pfc: Validate pinmux tables at runtime when debugging")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Improve wording while at it.
Fixes: 6161b39a14 ("pinctrl: sh-pfc: Validate pinmux tables at runtime when debugging")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds I2C{0,3,5} pins, groups and functions to the R8A7796 SoC.
These pins are physically muxed with other pins. Therefore, setup of
MOD_SEL is needed for exclusive control with other pins.
[takeshi.kihara.df: add blank lines after function declarations]
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[uli: use standard macros PINMUX_IPSR_PHYS and PINMUX_IPSR_PHYS_MSEL]
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Pin data for I2C controllers 0, 3 and 5 is properly defined already.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of Feb
12, 2019, the sel_ndfc MOD_SEL register bit is renamed to sel_ndf.
Update the pin control drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car E3]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 0.80 of Dec
22, 2017, and the Errata for Rev 1.50 of Dec 25, 2018, MOD_SEL0 register
bits 3, 4, 17, and 18 are renamed from SEL_ADG_{A,B,C} to
SEL_ADG{A,B,C}. Update the pin control drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of
Feb 12, 2019, the RTS{0,1,3,4}_#/TANS pin names defined in the GPSR and
IPSR registers are renamed to RTS{0,1,3,4}_#.
This patch updates the pin control drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car H3 ES1.x, V3M, V3H, and D3]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Jun 4, 2018, the CC5_OSCOUT pin is removed. Update the pin control
drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car V3M, V3H]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The HDMI CEC function is not supported by the R-Car Gen3 Hardware Manual
Rev 1.00. Therefore, delete the corresponding pin groups and functions,
and rename the HDMI[01]_CEC definitions to match their GPIO
functionality.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Squashed several commits]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, there is no need to configure MOD_SEL1 bit30 when the
SSI_SCK2_{A,B} or SSI_WS2_{A,B} pin functions are selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Remove now unused definitions, mark MOD_SEL1 bit30 reserved]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Aug 24, 2018, there is no need to configure MOD_SEL1 bit31 when the
SIM0_D_{A,B} pin function is selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Remove now unused definitions, mark MOD_SEL1 bit31 reserved]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, the MOD_SEL0 bit16 must be set to 0 when the NFALE_A and
NFRB_N_A pin functions are selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
- The IPSR field is meant for documentation only,
- The function name refers to the pin function, not to the IPSR
field.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Add a run-time check to the PINMUX_CFG_REG_VAR() macro, to ensure the
number of provided enum IDs is correct. This cannot be done at build
time, as the number of values depends on the variable-width fields in
the config register.
This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add build-time checks to the PINMUX_CFG_REG() and PINMUX_DATA_REG()
macros, to ensure the number of provided enum IDs is correct.
This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently the PINMUX_DATA_REG() macro must be followed by initialization
data, specifying all enum IDs. Hence the macro itself does not know
anything about the enum IDs, preventing the macro from performing any
validation on it.
Make the macro accept the enum IDs as a parameter, and update all users.
Note that array data enclosed by curly braces cannot be passed to a
macro as a parameter, hence the enum IDs are wrapped using the GROUP()
macro.
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently the PINMUX_CFG_REG_VAR() macro must be followed by
initialization data, specifying all enum IDs. Hence the macro itself
does not know anything about the enum IDs, preventing the macro from
performing any validation on it.
Make the macro accept the enum IDs as a parameter, and update all users.
Note that array data enclosed by curly braces cannot be passed to a
macro as a parameter, hence both the register field widths and the enum
IDs are wrapped using the GROUP() macro.
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently the PINMUX_CFG_REG() macro must be followed by initialization
data, specifying all enum IDs. Hence the macro itself does not know
anything about the enum IDs, preventing the macro from performing any
validation on it.
Make the macro accept the enum IDs as a parameter, and update all users.
Note that array data enclosed by curly braces cannot be passed to a
macro as a parameter, hence the enum IDs are wrapped using a new macro
GROUPS().
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable compile-testing of all Renesas SuperH and ARM pin control
drivers, in a similar way as was done before for clock and SoC drivers
in commits 371dd373c6 ("clk: renesas: Allow compile-testing of all
(sub)drivers") and 8be381a131 ("soc: renesas: Rework Kconfig and
Makefile logic").
The SuperH pin control drivers need specific include files, hence make
sure they are always found when compile-testing.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Source files using -Exxx error codes should include <linux/errno.h>.
On ARM, this header file is included indirectly; on SuperH, it is not,
leading to "error: ‘EINVAL’ undeclared" failures when enabling
compile-testing later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Pinctrl drivers for SuperH platforms use legacy function GPIOs.
Currently this support is compiled in based on the SUPERH platform
dependency, which hinders the introduction of compile-testing support
for the affected pinctrl drivers.
Introduce a new Kconfig symbol PINCTRL_SH_FUNC_GPIO, which is
auto-selected when needed. This symbol in turn selects
PINCTRL_SH_PFC_GPIO, to reduce the number of per-driver selects.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Perform some basic sanity checks on all built-in pinmux tables when
DEBUG is defined, to help catching bugs early.
For now the following checks are included:
- Check register and field widths in descriptors for config registers
with variable-width fields,
- Check relations between pin groups and functions:
- All pin functions must refer to existing pin groups,
- All pin groups must be referred to by a pin function,
- Warn if a pin group is referred to by multiple pin functions
(which is OK for backwards-compatibility aliases),
- Provide suggestions for reducing table sizes: reserved fields of
more than 3 bits can better be split in smaller subfields, as the
storage need is proportional to the square of the width of the
(sub)field,
Note that a dummy non-matching entry is added to the DT match table for
checking r8a7795es1_pinmux_info, as R-Car H3 ES1.0 is matched using
soc_device_match() in r8a7795_pinmux_init(), instead of by the DT match
table.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The TDSELCTRL register is responsible for configuring the SDHI/MMC clock
return path delay and may be adjusted by the bootloader. Retain the value
across suspend/resume to prevent hardware instability after resume.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
CANFD is found also on the R8A774C0, therefore move CANFD pin
groups and functions to "common".
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Linus Torvalds
Geert Uytterhoeven
Masahiro Yamada
Takeshi Kihara
Ulrich Hecht
Marek Vasut
Fabrizio Castro