commit 5260bd6d36 upstream.
This reverts commit d5af729dc2.
d5af729dc2 ("PCI: Mark NVIDIA T4 GPUs to avoid bus reset") avoided
Secondary Bus Reset on the T4 because the reset seemed to not work when the
T4 was directly attached to a Root Port.
But NVIDIA thinks the issue is probably related to some issue with the Root
Port, not with the T4. The T4 provides neither PM nor FLR reset, so
masking bus reset compromises this device for assignment scenarios.
Revert d5af729dc2 as requested by Wu Zongyong. This will leave SBR
broken in the specific configuration Wu tested, as it was in v6.5, so Wu
will debug that further.
Link: https://lore.kernel.org/r/ZPqMCDWvITlOLHgJ@wuzongyong-alibaba
Link: https://lore.kernel.org/r/20230908201104.GA305023@bhelgaas
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdb50033dd upstream.
A 32-bit mask was used on the 64-bit PCI address used for mapping MSIs.
This would result in the upper 32 bits being unintentionally zeroed and
MSIs getting mapped to incorrect PCI addresses if the address had any
of the upper bits set.
Replace 32-bit mask by appropriate 64-bit mask.
[kwilczynski: use GENMASK_ULL() over GENMASK() for 32-bit compatibility]
Fixes: dc73ed0f1b ("PCI: rockchip: Fix window mapping and address translation for endpoint")
Closes: https://lore.kernel.org/linux-pci/8d19e5b7-8fa0-44a4-90e2-9bb06f5eb694@moroto.mountain
Link: https://lore.kernel.org/linux-pci/20230703085845.2052008-1-rick.wertenbroek@gmail.com
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 17cf8661ee ]
The endpoint controller loses the Maximum Link Width and Supported Link Speed
value from the Link Capabilities Register - initially configured by the Reset
Configuration Word (RCW) - during a link-down or hot reset event.
Address this issue in the endpoint event handler.
Link: https://lore.kernel.org/r/20230720135834.1977616-2-Frank.Li@nxp.com
Fixes: a805770d8a ("PCI: layerscape: Add EP mode support")
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 061cbfab09 ]
Layerscape has PME interrupt, which can be used as linkup notifier. Set
CFG_READY bit of PEX_PF0_CONFIG to enable accesses from root complex when
linkup detected.
Link: https://lore.kernel.org/r/20230515151049.2797105-1-Frank.Li@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Stable-dep-of: 17cf8661ee ("PCI: layerscape: Add workaround for lost link capabilities during reset")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a37beefbde ]
Factor out this pattern:
if (!pci->ops || !pci->ops->start_link)
return -EINVAL;
return pci->ops->start_link(pci);
into a new dw_pcie_start_link() wrapper and do the same for the stop_link()
method.
Note that dw_pcie_ep_start() previously returned -EINVAL if there was no
platform start_link() method, which didn't make much sense since that is
not an error. It will now return 0 in that case.
As a side-effect, drop the empty start_link() and dummy dw_pcie_ops
instances from the generic DW PCIe and Layerscape EP platform drivers.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143428.8334-14-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Stable-dep-of: 17cf8661ee ("PCI: layerscape: Add workaround for lost link capabilities during reset")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e09060b3b6 ]
Don't assume that the device is fully under the control of ASPM and use RMW
capability accessors which do proper locking to avoid losing concurrent
updates to the register values.
If configuration fails in pcie_aspm_configure_common_clock(), the
function attempts to restore the old PCI_EXP_LNKCTL_CCC settings. Store
only the old PCI_EXP_LNKCTL_CCC bit for the relevant devices rather
than the content of the whole LNKCTL registers. It aligns better with
how pcie_lnkctl_clear_and_set() expects its parameter and makes the
code more obvious to understand.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Fixes: 2a42d9dba7 ("PCIe: ASPM: Break out of endless loop waiting for PCI config bits to switch")
Fixes: 7d715a6c1a ("PCI: add PCI Express ASPM support")
Link: https://lore.kernel.org/r/20230717120503.15276-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f75f96c61 ]
As hotplug is not the only driver touching LNKCTL, use the RMW capability
accessor which handles concurrent changes correctly.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Fixes: 7f822999e1 ("PCI: pciehp: Add Disable/enable link functions")
Link: https://lore.kernel.org/r/20230717120503.15276-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5af729dc2 ]
NVIDIA T4 GPUs do not work with SBR. This problem is found when the T4 card
is direct attached to a Root Port only. Avoid bus reset by marking T4 GPUs
PCI_DEV_FLAGS_NO_BUS_RESET.
Fixes: 4c207e7121 ("PCI: Mark some NVIDIA GPUs to avoid bus reset")
Link: https://lore.kernel.org/r/2dcebea53a6eb9bd212ec6d8974af2e5e0333ef6.1681129861.git.wuzongyong@linux.alibaba.com
Signed-off-by: Wu Zongyong <wuzongyong@linux.alibaba.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d473a5a26 ]
The SEC and DED interrupt bits are laid out the wrong way round so the SEC
interrupt handler attempts to mask, unmask, and clear the DED interrupt
and vice versa. Correct the bit offsets so that each interrupt handler
operates properly.
Link: https://lore.kernel.org/r/20230728131401.1615724-2-daire.mcnamara@microchip.com
Fixes: 6f15a9c9f9 ("PCI: microchip: Add Microchip PolarFire PCIe controller driver")
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cc22522fd5 upstream.
40613da52b ("PCI: acpiphp: Reassign resources on bridge if necessary")
changed acpiphp hotplug to use pci_assign_unassigned_bridge_resources()
which depends on bridge being available, however enable_slot() can be
called without bridge associated:
1. Legitimate case of hotplug on root bus (widely used in virt world)
2. A (misbehaving) firmware, that sends ACPI Bus Check notifications to
non existing root ports (Dell Inspiron 7352/0W6WV0), which end up at
enable_slot(..., bridge = 0) where bus has no bridge assigned to it.
acpihp doesn't know that it's a bridge, and bus specific 'PCI
subsystem' can't augment ACPI context with bridge information since
the PCI device to get this data from is/was not available.
Issue is easy to reproduce with QEMU's 'pc' machine, which supports PCI
hotplug on hostbridge slots. To reproduce, boot kernel at commit
40613da52b in VM started with following CLI (assuming guest root fs is
installed on sda1 partition):
# qemu-system-x86_64 -M pc -m 1G -enable-kvm -cpu host \
-monitor stdio -serial file:serial.log \
-kernel arch/x86/boot/bzImage \
-append "root=/dev/sda1 console=ttyS0" \
guest_disk.img
Once guest OS is fully booted at qemu prompt:
(qemu) device_add e1000
(check serial.log) it will cause NULL pointer dereference at:
void pci_assign_unassigned_bridge_resources(struct pci_dev *bridge)
{
struct pci_bus *parent = bridge->subordinate;
BUG: kernel NULL pointer dereference, address: 0000000000000018
? pci_assign_unassigned_bridge_resources+0x1f/0x260
enable_slot+0x21f/0x3e0
acpiphp_hotplug_notify+0x13d/0x260
acpi_device_hotplug+0xbc/0x540
acpi_hotplug_work_fn+0x15/0x20
process_one_work+0x1f7/0x370
worker_thread+0x45/0x3b0
The issue was discovered on Dell Inspiron 7352/0W6WV0 laptop with following
sequence:
1. Suspend to RAM
2. Wake up with the same backtrace being observed:
3. 2nd suspend to RAM attempt makes laptop freeze
Fix it by using __pci_bus_assign_resources() instead of
pci_assign_unassigned_bridge_resources() as we used to do, but only in case
when bus doesn't have a bridge associated (to cover for the case of ACPI
event on hostbridge or non existing root port).
That lets us keep hotplug on root bus working like it used to and at the
same time keeps resource reassignment usable on root ports (and other 1st
level bridges) that was fixed by 40613da52b.
Fixes: 40613da52b ("PCI: acpiphp: Reassign resources on bridge if necessary")
Link: https://lore.kernel.org/r/20230726123518.2361181-2-imammedo@redhat.com
Reported-by: Woody Suwalski <terraluna977@gmail.com>
Tested-by: Woody Suwalski <terraluna977@gmail.com>
Tested-by: Michal Koutný <mkoutny@suse.com>
Link: https://lore.kernel.org/r/11fc981c-af49-ce64-6b43-3e282728bd1a@gmail.com
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 40613da52b ]
When using ACPI PCI hotplug, hotplugging a device with large BARs may fail
if bridge windows programmed by firmware are not large enough.
Reproducer:
$ qemu-kvm -monitor stdio -M q35 -m 4G \
-global ICH9-LPC.acpi-pci-hotplug-with-bridge-support=on \
-device id=rp1,pcie-root-port,bus=pcie.0,chassis=4 \
disk_image
wait till linux guest boots, then hotplug device:
(qemu) device_add qxl,bus=rp1
hotplug on guest side fails with:
pci 0000:01:00.0: [1b36:0100] type 00 class 0x038000
pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x03ffffff]
pci 0000:01:00.0: reg 0x14: [mem 0x00000000-0x03ffffff]
pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00001fff]
pci 0000:01:00.0: reg 0x1c: [io 0x0000-0x001f]
pci 0000:01:00.0: BAR 0: no space for [mem size 0x04000000]
pci 0000:01:00.0: BAR 0: failed to assign [mem size 0x04000000]
pci 0000:01:00.0: BAR 1: no space for [mem size 0x04000000]
pci 0000:01:00.0: BAR 1: failed to assign [mem size 0x04000000]
pci 0000:01:00.0: BAR 2: assigned [mem 0xfe800000-0xfe801fff]
pci 0000:01:00.0: BAR 3: assigned [io 0x1000-0x101f]
qxl 0000:01:00.0: enabling device (0000 -> 0003)
Unable to create vram_mapping
qxl: probe of 0000:01:00.0 failed with error -12
However when using native PCIe hotplug
'-global ICH9-LPC.acpi-pci-hotplug-with-bridge-support=off'
it works fine, since kernel attempts to reassign unused resources.
Use the same machinery as native PCIe hotplug to (re)assign resources.
Link: https://lore.kernel.org/r/20230424191557.2464760-1-imammedo@redhat.com
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 205b3d02d5 ]
Add check to fix the possible array out of bounds violation by
making speed equal to GEN1_CORE_CLK_FREQ when its value is more
than the size of "pcie_gen_freq" array. This array has size of
four but possible speed (CLS) values are from "0 to 0xF". So,
"speed - 1" values are "-1 to 0xE".
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Link: https://lore.kernel.org/lkml/72b9168b-d4d6-4312-32ea-69358df2f2d0@nvidia.com/
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a52587e0be ]
The RK3399 PCIe endpoint controller cannot generate MSI-X IRQs.
This is documented in the RK3399 technical reference manual (TRM)
section 17.5.9 "Interrupt Support".
MSI-X capability should therefore not be advertised. Remove the
MSI-X capability by editing the capability linked-list. The
previous entry is the MSI capability, therefore get the next
entry from the MSI-X capability entry and set it as next entry
for the MSI capability. This in effect removes MSI-X from the list.
Linked list before : MSI cap -> MSI-X cap -> PCIe Device cap -> ...
Linked list now : MSI cap -> PCIe Device cap -> ...
Link: https://lore.kernel.org/r/20230418074700.1083505-11-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc73ed0f1b ]
The RK3399 PCI endpoint core has 33 windows for PCIe space, now in the
driver up to 32 fixed size (1M) windows are used and pages are allocated
and mapped accordingly. The driver first used a single window and allocated
space inside which caused translation issues (between CPU space and PCI
space) because a window can only have a single translation at a given
time, which if multiple pages are allocated inside will cause conflicts.
Now each window is a single region of 1M which will always guarantee that
the translation is not in conflict.
Set the translation register addresses for physical function. As documented
in the technical reference manual (TRM) section 17.5.5 "PCIe Address
Translation" and section 17.6.8 "Address Translation Registers Description"
Link: https://lore.kernel.org/r/20230418074700.1083505-9-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92a9c57c32 ]
Remove write accesses to registers that are marked "unused" (and
therefore read-only) in the technical reference manual (TRM)
(see RK3399 TRM 17.6.8.1)
Link: https://lore.kernel.org/r/20230418074700.1083505-2-rick.wertenbroek@gmail.com
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Stable-dep-of: dc73ed0f1b ("PCI: rockchip: Fix window mapping and address translation for endpoint")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7e3975636 ]
PCIe r6.0.1, sec 7.5.3.7, recommends setting the link control parameters,
then waiting for the Link Training bit to be clear before setting the
Retrain Link bit.
This avoids a race where the LTSSM may not use the updated parameters if it
is already in the midst of link training because of other normal link
activity.
Wait for the Link Training bit to be clear before toggling the Retrain Link
bit to ensure that the LTSSM uses the updated link control parameters.
[bhelgaas: commit log, return 0 (success)/-ETIMEDOUT instead of bool for
both pcie_wait_for_retrain() and the existing pcie_retrain_link()]
Suggested-by: Lukas Wunner <lukas@wunner.de>
Fixes: 7d715a6c1a ("PCI: add PCI Express ASPM support")
Link: https://lore.kernel.org/r/20230502083923.34562-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5297a01ee ]
"pcie_retrain_link" is not a question with a true/false answer, so "bool"
isn't quite the right return type. Return 0 for success or -ETIMEDOUT if
the retrain failed. No functional change intended.
[bhelgaas: based on Ilpo's patch below]
Link: https://lore.kernel.org/r/20230502083923.34562-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Stable-dep-of: e7e3975636 ("PCI/ASPM: Avoid link retraining race")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7e6689b34a upstream.
The address translation unit of the rockchip EP controller does not use
the lower 8 bits of a PCIe-space address to map local memory. Thus we
must set the align feature field to 256 to let the user know about this
constraint.
Link: https://lore.kernel.org/r/20230418074700.1083505-12-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8962b2cb39 upstream.
Previously u16 variables were used to access 32-bit registers, this
resulted in not all of the data being read from the registers. Also
the left shift of more than 16-bits would result in moving data out
of the variable. Use u32 variables to access 32-bit registers
Link: https://lore.kernel.org/r/20230418074700.1083505-10-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 166e89d99d upstream.
Fix legacy IRQ generation for RK3399 PCIe endpoint core according to
the technical reference manual (TRM). Assert and deassert legacy
interrupt (INTx) through the legacy interrupt control register
("PCIE_CLIENT_LEGACY_INT_CTRL") instead of manually generating a PCIe
message. The generation of the legacy interrupt was tested and validated
with the PCIe endpoint test driver.
Link: https://lore.kernel.org/r/20230418074700.1083505-8-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9dd3c7c4c8 upstream.
The RK3399 PCIe controller should wait until the PHY PLLs are locked.
Add poll and timeout to wait for PHY PLLs to be locked. If they cannot
be locked generate error message and jump to error handler. Accessing
registers in the PHY clock domain when PLLs are not locked causes hang
The PHY PLLs status is checked through a side channel register.
This is documented in the TRM section 17.5.8.1 "PCIe Initialization
Sequence".
Link: https://lore.kernel.org/r/20230418074700.1083505-5-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f1c42ece1 upstream.
Write PCI Device ID (DID) to the correct register. The Device ID was not
updated through the correct register. Device ID was written to a read-only
register and therefore did not work. The Device ID is now set through the
correct register. This is documented in the RK3399 TRM section 17.6.6.1.1
Link: https://lore.kernel.org/r/20230418074700.1083505-3-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f397fd4ac1 upstream.
Assert PCI Configuration Enable bit after probe. When this bit is left to
0 in the endpoint mode, the RK3399 PCIe endpoint core will generate
configuration request retry status (CRS) messages back to the root complex.
Assert this bit after probe to allow the RK3399 PCIe endpoint core to reply
to configuration requests from the root complex.
This is documented in section 17.5.8.1.2 of the RK3399 TRM.
Link: https://lore.kernel.org/r/20230418074700.1083505-4-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a33d700e8e upstream.
In the post init sequence of v2.9.0, write access to read only registers
are not disabled after updating the registers. Fix it by disabling the
access after register update.
Link: https://lore.kernel.org/r/20230619150408.8468-2-manivannan.sadhasivam@linaro.org
Fixes: 5d76117f07 ("PCI: qcom: Add support for IPQ8074 PCIe controller")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c60738de85 ]
Smatch reported:
1. drivers/pci/controller/pci-ftpci100.c:526 faraday_pci_probe() warn:
'clk' from clk_prepare_enable() not released on lines: 442,451,462,478,512,517.
2. drivers/pci/controller/pci-ftpci100.c:526 faraday_pci_probe() warn:
'p->bus_clk' from clk_prepare_enable() not released on lines: 451,462,478,512,517.
The clock resource is obtained by devm_clk_get(), and then
clk_prepare_enable() makes the clock resource ready for use. After that,
clk_disable_unprepare() should be called to release the clock resource
when it is no longer needed. However, while doing some error handling
in faraday_pci_probe(), clk_disable_unprepare() is not called to release
clk and p->bus_clk before returning. These return lines are exactly 442,
451, 462, 478, 512, 517.
Fix this warning by replacing devm_clk_get() with devm_clk_get_enabled(),
which is equivalent to devm_clk_get() + clk_prepare_enable(). And with
devm_clk_get_enabled(), the clock will automatically be disabled,
unprepared and freed when the device is unbound from the bus.
Link: https://lore.kernel.org/r/20230508043641.23807-1-yejunyan@hust.edu.cn
Fixes: b3c433efb8 ("PCI: faraday: Fix wrong pointer passed to PTR_ERR()")
Fixes: 2eeb02b285 ("PCI: faraday: Add clock handling")
Fixes: 783a862563 ("PCI: faraday: Use pci_parse_request_of_pci_ranges()")
Fixes: d3c68e0a7e ("PCI: faraday: Add Faraday Technology FTPCI100 PCI Host Bridge driver")
Fixes: f1e8bd21e3 ("PCI: faraday: Convert IRQ masking to raw PCI config accessors")
Signed-off-by: Junyan Ye <yejunyan@hust.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8afd0d9fc ]
If a PCIe hotplug slot has an Attention Button, the normal hot-add flow is:
- Slot is empty and slot power is off
- User inserts card in slot and presses Attention Button
- OS blinks Power Indicator for 5 seconds
- After 5 seconds, OS turns on Power Indicator, turns on slot power, and
enumerates the device
Previously, if a user pressed the Attention Button on an *empty* slot,
pciehp logged the following messages and blinked the Power Indicator
until a second button press:
[0.000] pciehp: Button press: will power on in 5 sec
[0.001] # Power Indicator starts blinking
[5.001] # 5 second timeout; slot is empty, so we should cancel the
request to power on and turn off Power Indicator
[7.000] # Power Indicator still blinking
[8.000] # possible card insertion
[9.000] pciehp: Button press: canceling request to power on
The first button press incorrectly left the slot in BLINKINGON_STATE, so
the second was interpreted as a "cancel power on" event regardless of
whether a card was present.
If the slot is empty, turn off the Power Indicator and return from
BLINKINGON_STATE to OFF_STATE after 5 seconds, effectively canceling the
request to power on. Putting the slot in OFF_STATE also means the second
button press will correctly request a slot power on if the slot is
occupied.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20230512021518.336460-1-clementwei90@163.com
Fixes: d331710ea7 ("PCI: pciehp: Become resilient to missed events")
Suggested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rongguang Wei <weirongguang@kylinos.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 456d8aa37d ]
Struct pcie_link_state->downstream is a pointer to the pci_dev of function
0. Previously we retained that pointer when removing function 0, and
subsequent ASPM policy changes dereferenced it, resulting in a
use-after-free warning from KASAN, e.g.:
# echo 1 > /sys/bus/pci/devices/0000:03:00.0/remove
# echo powersave > /sys/module/pcie_aspm/parameters/policy
BUG: KASAN: slab-use-after-free in pcie_config_aspm_link+0x42d/0x500
Call Trace:
kasan_report+0xae/0xe0
pcie_config_aspm_link+0x42d/0x500
pcie_aspm_set_policy+0x8e/0x1a0
param_attr_store+0x162/0x2c0
module_attr_store+0x3e/0x80
PCIe spec r6.0, sec 7.5.3.7, recommends that software program the same ASPM
Control value in all functions of multi-function devices.
Disable ASPM and free the pcie_link_state when any child function is
removed so we can discard the dangling pcie_link_state->downstream pointer
and maintain the same ASPM Control configuration for all functions.
[bhelgaas: commit log and comment]
Debugged-by: Zongquan Qin <qinzongquan@sangfor.com.cn>
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Fixes: b5a0a9b59c ("PCI/ASPM: Read and set up L1 substate capabilities")
Link: https://lore.kernel.org/r/20230507034057.20970-1-dinghui@sangfor.com.cn
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b61cf04c49 ]
VMD driver can disable or enable MSI remapping by changing
VMCONFIG_MSI_REMAP register. This register needs to be set to the
default value during soft reboots. Drives failed to enumerate
when Windows boots after performing a soft reboot from Linux.
Windows doesn't support MSI remapping disable feature and stale
register value hinders Windows VMD driver initialization process.
Adding vmd_shutdown function to make sure to set the VMCONFIG
register to the default value.
Link: https://lore.kernel.org/r/20230224202811.644370-1-nirmal.patel@linux.intel.com
Fixes: ee81ee84f8 ("PCI: vmd: Disable MSI-X remapping when possible")
Signed-off-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Jon Derrick <jonathan.derrick@linux.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e12f83023 ]
The Link Retraining process is initiated to account for the Gen2 defect in
the Cadence PCIe controller in J721E SoC. The errata corresponding to this
is i2085, documented at:
https://www.ti.com/lit/er/sprz455c/sprz455c.pdf
The existing workaround implemented for the errata waits for the Data Link
initialization to complete and assumes that the link retraining process
at the Physical Layer has completed. However, it is possible that the
Physical Layer training might be ongoing as indicated by the
PCI_EXP_LNKSTA_LT bit in the PCI_EXP_LNKSTA register.
Fix the existing workaround, to ensure that the Physical Layer training
has also completed, in addition to the Data Link initialization.
Link: https://lore.kernel.org/r/20230315070800.1615527-1-s-vadapalli@ti.com
Fixes: 4740b969aa ("PCI: cadence: Retrain Link to work around Gen2 training defect")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 067d6ec7ed upstream.
In the case of fast device addition/removal, it's possible that
hv_eject_device_work() can start to run before create_root_hv_pci_bus()
starts to run; as a result, the pci_get_domain_bus_and_slot() in
hv_eject_device_work() can return a 'pdev' of NULL, and
hv_eject_device_work() can remove the 'hpdev', and immediately send a
message PCI_EJECTION_COMPLETE to the host, and the host immediately
unassigns the PCI device from the guest; meanwhile,
create_root_hv_pci_bus() and the PCI device driver can be probing the
dead PCI device and reporting timeout errors.
Fix the issue by adding a per-bus mutex 'state_lock' and grabbing the
mutex before powering on the PCI bus in hv_pci_enter_d0(): when
hv_eject_device_work() starts to run, it's able to find the 'pdev' and call
pci_stop_and_remove_bus_device(pdev): if the PCI device driver has
loaded, the PCI device driver's probe() function is already called in
create_root_hv_pci_bus() -> pci_bus_add_devices(), and now
hv_eject_device_work() -> pci_stop_and_remove_bus_device() is able
to call the PCI device driver's remove() function and remove the device
reliably; if the PCI device driver hasn't loaded yet, the function call
hv_eject_device_work() -> pci_stop_and_remove_bus_device() is able to
remove the PCI device reliably and the PCI device driver's probe()
function won't be called; if the PCI device driver's probe() is already
running (e.g., systemd-udev is loading the PCI device driver), it must
be holding the per-device lock, and after the probe() finishes and releases
the lock, hv_eject_device_work() -> pci_stop_and_remove_bus_device() is
able to proceed to remove the device reliably.
Fixes: 4daace0d8c ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230615044451.5580-6-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2738d5ab79 upstream.
When the host tries to remove a PCI device, the host first sends a
PCI_EJECT message to the guest, and the guest is supposed to gracefully
remove the PCI device and send a PCI_EJECTION_COMPLETE message to the host;
the host then sends a VMBus message CHANNELMSG_RESCIND_CHANNELOFFER to
the guest (when the guest receives this message, the device is already
unassigned from the guest) and the guest can do some final cleanup work;
if the guest fails to respond to the PCI_EJECT message within one minute,
the host sends the VMBus message CHANNELMSG_RESCIND_CHANNELOFFER and
removes the PCI device forcibly.
In the case of fast device addition/removal, it's possible that the PCI
device driver is still configuring MSI-X interrupts when the guest receives
the PCI_EJECT message; the channel callback calls hv_pci_eject_device(),
which sets hpdev->state to hv_pcichild_ejecting, and schedules a work
hv_eject_device_work(); if the PCI device driver is calling
pci_alloc_irq_vectors() -> ... -> hv_compose_msi_msg(), we can break the
while loop in hv_compose_msi_msg() due to the updated hpdev->state, and
leave data->chip_data with its default value of NULL; later, when the PCI
device driver calls request_irq() -> ... -> hv_irq_unmask(), the guest
crashes in hv_arch_irq_unmask() due to data->chip_data being NULL.
Fix the issue by not testing hpdev->state in the while loop: when the
guest receives PCI_EJECT, the device is still assigned to the guest, and
the guest has one minute to finish the device removal gracefully. We don't
really need to (and we should not) test hpdev->state in the loop.
Fixes: de0aa7b2f9 ("PCI: hv: Fix 2 hang issues in hv_compose_msi_msg()")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230615044451.5580-3-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit add9195e69 upstream.
The hpdev->state is never really useful. The only use in
hv_pci_eject_device() and hv_eject_device_work() is not really necessary.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230615044451.5580-4-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a847234e24 upstream.
This reverts commit d6af2ed29c.
The statement "the hv_pci_bus_exit() call releases structures of all its
child devices" in commit d6af2ed29c is not true: in the path
hv_pci_probe() -> hv_pci_enter_d0() -> hv_pci_bus_exit(hdev, true): the
parameter "keep_devs" is true, so hv_pci_bus_exit() does *not* release the
child "struct hv_pci_dev *hpdev" that is created earlier in
pci_devices_present_work() -> new_pcichild_device().
The commit d6af2ed29c was originally made in July 2020 for RHEL 7.7,
where the old version of hv_pci_bus_exit() was used; when the commit was
rebased and merged into the upstream, people didn't notice that it's
not really necessary. The commit itself doesn't cause any issue, but it
makes hv_pci_probe() more complicated. Revert it to facilitate some
upcoming changes to hv_pci_probe().
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Wei Hu <weh@microsoft.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230615044451.5580-5-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 440b5e3663 upstream.
Since day 1 of the driver, there has been a race between
hv_pci_query_relations() and survey_child_resources(): during fast
device hotplug, hv_pci_query_relations() may error out due to
device-remove and the stack variable 'comp' is no longer valid;
however, pci_devices_present_work() -> survey_child_resources() ->
complete() may be running on another CPU and accessing the no-longer-valid
'comp'. Fix the race by flushing the workqueue before we exit from
hv_pci_query_relations().
Fixes: 4daace0d8c ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230615044451.5580-2-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c441b1e03d ]
During EDR recovery, the OS must clear error status of the port that
triggered DPC even if firmware retains control of DPC and AER (see the
implementation note in the PCI Firmware spec r3.3, sec 4.6.12).
Prior to 068c29a248 ("PCI/ERR: Clear PCIe Device Status errors only if
OS owns AER"), the port Device Status was cleared in this path:
edr_handle_event
dpc_process_error(dev) # "dev" triggered DPC
pcie_do_recovery(dev, dpc_reset_link)
dpc_reset_link # exit DPC
pcie_clear_device_status(dev) # clear Device Status
After 068c29a248, pcie_do_recovery() no longer clears Device Status when
firmware controls AER, so the error bit remains set even after recovery.
Per the "Downstream Port Containment configuration control" bit in the
returned _OSC Control Field (sec 4.5.1), the OS is allowed to clear error
status until it evaluates _OST, so clear Device Status in
edr_handle_event() if the error recovery was successful.
[bhelgaas: commit log]
Fixes: 068c29a248 ("PCI/ERR: Clear PCIe Device Status errors only if OS owns AER")
Link: https://lore.kernel.org/r/20230315235449.1279209-1-sathyanarayanan.kuppuswamy@linux.intel.com
Reported-by: Tsaur Erwin <erwin.tsaur@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f5ac460df ]
commit bb38919ec5 ("PCI: imx6: Add support for i.MX6 PCIe controller")
added a fault hook to this driver in the probe function. So it was only
installed if needed.
commit bde4a5a00e ("PCI: imx6: Allow probe deferral by reset GPIO")
moved it from probe to driver init which installs the hook unconditionally
as soon as the driver is compiled into a kernel.
When this driver is compiled as a module, the hook is not registered
until after the driver has been matched with a .compatible and
loaded.
commit 415b6185c5 ("PCI: imx6: Fix config read timeout handling")
extended the fault handling code.
commit 2d8ed461db ("PCI: imx6: Add support for i.MX8MQ")
added some protection for non-ARM architectures, but this does not
protect non-i.MX ARM architectures.
Since fault handlers can be triggered on any architecture for different
reasons, there is no guarantee that they will be triggered only for the
assumed situation, leading to improper error handling (i.MX6-specific
imx6q_pcie_abort_handler) on foreign systems.
I had seen strange L3 imprecise external abort messages several times on
OMAP4 and OMAP5 devices and couldn't make sense of them until I realized
they were related to this unused imx6q driver because I had
CONFIG_PCI_IMX6=y.
Note that CONFIG_PCI_IMX6=y is useful for kernel binaries that are designed
to run on different ARM SoC and be differentiated only by device tree
binaries. So turning off CONFIG_PCI_IMX6 is not a solution.
Therefore we check the compatible in the init function before registering
the fault handler.
Link: https://lore.kernel.org/r/e1bcfc3078c82b53aa9b78077a89955abe4ea009.1678380991.git.hns@goldelico.com
Fixes: bde4a5a00e ("PCI: imx6: Allow probe deferral by reset GPIO")
Fixes: 415b6185c5 ("PCI: imx6: Fix config read timeout handling")
Fixes: 2d8ed461db ("PCI: imx6: Add support for i.MX8MQ")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2542e16c39 upstream.
Qcom PCIe IP version v2.7.0 and its derivatives don't contain the
PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT register. Instead, they have the new
PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 register. So fix the incorrect
register usage which is modifying a different register.
Also in this IP version, this register change doesn't depend on MSI
being enabled. So remove that check also.
Link: https://lore.kernel.org/r/20230316081117.14288-2-manivannan.sadhasivam@linaro.org
Fixes: ed8cc3b1fc ("PCI: qcom: Add support for SDM845 PCIe controller")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: <stable@vger.kernel.org> # 5.6+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5eff5591b upstream.
In 2013, commits
2e35afaefe ("PCI: pciehp: Add reset_slot() method")
608c388122 ("PCI: Add slot reset option to pci_dev_reset()")
amended PCIe hotplug to mask Presence Detect Changed events during a
Secondary Bus Reset. The reset thus no longer causes gratuitous slot
bringdown and bringup.
However the commits neglected to serialize reset with code paths reading
slot registers. For instance, a slot bringup due to an earlier hotplug
event may see the Presence Detect State bit cleared during a concurrent
Secondary Bus Reset.
In 2018, commit
5b3f7b7d06 ("PCI: pciehp: Avoid slot access during reset")
retrofitted the missing locking. It introduced a reset_lock which
serializes a Secondary Bus Reset with other parts of pciehp.
Unfortunately the locking turns out to be overzealous: reset_lock is
held for the entire enumeration and de-enumeration of hotplugged devices,
including driver binding and unbinding.
Driver binding and unbinding acquires device_lock while the reset_lock
of the ancestral hotplug port is held. A concurrent Secondary Bus Reset
acquires the ancestral reset_lock while already holding the device_lock.
The asymmetric locking order in the two code paths can lead to AB-BA
deadlocks.
Michael Haeuptle reports such deadlocks on simultaneous hot-removal and
vfio release (the latter implies a Secondary Bus Reset):
pciehp_ist() # down_read(reset_lock)
pciehp_handle_presence_or_link_change()
pciehp_disable_slot()
__pciehp_disable_slot()
remove_board()
pciehp_unconfigure_device()
pci_stop_and_remove_bus_device()
pci_stop_bus_device()
pci_stop_dev()
device_release_driver()
device_release_driver_internal()
__device_driver_lock() # device_lock()
SYS_munmap()
vfio_device_fops_release()
vfio_device_group_close()
vfio_device_close()
vfio_device_last_close()
vfio_pci_core_close_device()
vfio_pci_core_disable() # device_lock()
__pci_reset_function_locked()
pci_reset_bus_function()
pci_dev_reset_slot_function()
pci_reset_hotplug_slot()
pciehp_reset_slot() # down_write(reset_lock)
Ian May reports the same deadlock on simultaneous hot-removal and an
AER-induced Secondary Bus Reset:
aer_recover_work_func()
pcie_do_recovery()
aer_root_reset()
pci_bus_error_reset()
pci_slot_reset()
pci_slot_lock() # device_lock()
pci_reset_hotplug_slot()
pciehp_reset_slot() # down_write(reset_lock)
Fix by releasing the reset_lock during driver binding and unbinding,
thereby splitting and shrinking the critical section.
Driver binding and unbinding is protected by the device_lock() and thus
serialized with a Secondary Bus Reset. There's no need to additionally
protect it with the reset_lock. However, pciehp does not bind and
unbind devices directly, but rather invokes PCI core functions which
also perform certain enumeration and de-enumeration steps.
The reset_lock's purpose is to protect slot registers, not enumeration
and de-enumeration of hotplugged devices. That would arguably be the
job of the PCI core, not the PCIe hotplug driver. After all, an
AER-induced Secondary Bus Reset may as well happen during boot-time
enumeration of the PCI hierarchy and there's no locking to prevent that
either.
Exempting *de-enumeration* from the reset_lock is relatively harmless:
A concurrent Secondary Bus Reset may foil config space accesses such as
PME interrupt disablement. But if the device is physically gone, those
accesses are pointless anyway. If the device is physically present and
only logically removed through an Attention Button press or the sysfs
"power" attribute, PME interrupts as well as DMA cannot come through
because pciehp_unconfigure_device() disables INTx and Bus Master bits.
That's still protected by the reset_lock in the present commit.
Exempting *enumeration* from the reset_lock also has limited impact:
The exempted call to pci_bus_add_device() may perform device accesses
through pcibios_bus_add_device() and pci_fixup_device() which are now
no longer protected from a concurrent Secondary Bus Reset. Otherwise
there should be no impact.
In essence, the present commit seeks to fix the AB-BA deadlocks while
still retaining a best-effort reset protection for enumeration and
de-enumeration of hotplugged devices -- until a general solution is
implemented in the PCI core.
Link: https://lore.kernel.org/linux-pci/CS1PR8401MB0728FC6FDAB8A35C22BD90EC95F10@CS1PR8401MB0728.NAMPRD84.PROD.OUTLOOK.COM
Link: https://lore.kernel.org/linux-pci/20200615143250.438252-1-ian.may@canonical.com
Link: https://lore.kernel.org/linux-pci/ce878dab-c0c4-5bd0-a725-9805a075682d@amd.com
Link: https://lore.kernel.org/linux-pci/ed831249-384a-6d35-0831-70af191e9bce@huawei.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215590
Fixes: 5b3f7b7d06 ("PCI: pciehp: Avoid slot access during reset")
Link: https://lore.kernel.org/r/fef2b2e9edf245c049a8c5b94743c0f74ff5008a.1681191902.git.lukas@wunner.de
Reported-by: Michael Haeuptle <michael.haeuptle@hpe.com>
Reported-by: Ian May <ian.may@canonical.com>
Reported-by: Andrey Grodzovsky <andrey2805@gmail.com>
Reported-by: Rahul Kumar <rahul.kumar1@amd.com>
Reported-by: Jialin Zhang <zhangjialin11@huawei.com>
Tested-by: Anatoli Antonovitch <Anatoli.Antonovitch@amd.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.19+
Cc: Dan Stein <dstein@hpe.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Alex Michon <amichon@kalrayinc.com>
Cc: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Sathyanarayanan Kuppuswamy <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08d0cc5f34 upstream.
pcie_aspm_pm_state_change() was introduced at the inception of PCIe ASPM
code, but it can cause some issues. For instance, when ASPM config is
changed via sysfs, those changes won't persist across power state change
because pcie_aspm_pm_state_change() overwrites them.
Also, if the driver restores L1SS [1] after system resume, the restored
state will also be overwritten by pcie_aspm_pm_state_change().
Remove pcie_aspm_pm_state_change(). If there's any hardware that really
needs it to function, a quirk can be used instead.
[1] https://lore.kernel.org/linux-pci/20220201123536.12962-1-vidyas@nvidia.com/
Link: https://lore.kernel.org/r/20220509073639.2048236-1-kai.heng.feng@canonical.com
[bhelgaas: remove additional pcie_aspm_pm_state_change() call in
pci_set_low_power_state(), added by
10aa5377fc ("PCI/PM: Split pci_raw_set_power_state()") and moved by
7957d20145 ("PCI/PM: Relocate pci_set_low_power_state()")]
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[manual backport: pci_set_low_power_state does not exist in v5.15]
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53b54ad074 upstream.
pci_bridge_wait_for_secondary_bus() is called after a Secondary Bus
Reset, but not after a DPC-induced Hot Reset.
As a result, the delays prescribed by PCIe r6.0 sec 6.6.1 are not
observed and devices on the secondary bus may be accessed before
they're ready.
One affected device is Intel's Ponte Vecchio HPC GPU. It comprises a
PCIe switch whose upstream port is not immediately ready after reset.
Because its config space is restored too early, it remains in
D0uninitialized, its subordinate devices remain inaccessible and DPC
recovery fails with messages such as:
i915 0000:8c:00.0: can't change power state from D3cold to D0 (config space inaccessible)
intel_vsec 0000:8e:00.1: can't change power state from D3cold to D0 (config space inaccessible)
pcieport 0000:89:02.0: AER: device recovery failed
Fix it.
Link: https://lore.kernel.org/r/9f5ff00e1593d8d9a4b452398b98aa14d23fca11.1673769517.git.lukas@wunner.de
Tested-by: Ravi Kishore Koppuravuri <ravi.kishore.koppuravuri@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac91e69805 upstream.
Sheng Bi reports that pci_bridge_secondary_bus_reset() may fail to wait
for devices on the secondary bus to become accessible after reset:
Although it does call pci_dev_wait(), it erroneously passes the bridge's
pci_dev rather than that of a child. The bridge of course is always
accessible while its secondary bus is reset, so pci_dev_wait() returns
immediately.
Sheng Bi proposes introducing a new pci_bridge_secondary_bus_wait()
function which is called from pci_bridge_secondary_bus_reset():
https://lore.kernel.org/linux-pci/20220523171517.32407-1-windy.bi.enflame@gmail.com/
However we already have pci_bridge_wait_for_secondary_bus() which does
almost exactly what we need. So far it's only called on resume from
D3cold (which implies a Fundamental Reset per PCIe r6.0 sec 5.8).
Re-using it for Secondary Bus Resets is a leaner and more rational
approach than introducing a new function.
That only requires a few minor tweaks:
- Amend pci_bridge_wait_for_secondary_bus() to await accessibility of
the first device on the secondary bus by calling pci_dev_wait() after
performing the prescribed delays. pci_dev_wait() needs two parameters,
a reset reason and a timeout, which callers must now pass to
pci_bridge_wait_for_secondary_bus(). The timeout is 1 sec for resume
(PCIe r6.0 sec 6.6.1) and 60 sec for reset (commit 821cdad5c4 ("PCI:
Wait up to 60 seconds for device to become ready after FLR")).
Introduce a PCI_RESET_WAIT macro for the 1 sec timeout.
- Amend pci_bridge_wait_for_secondary_bus() to return 0 on success or
-ENOTTY on error for consumption by pci_bridge_secondary_bus_reset().
- Drop an unnecessary 1 sec delay from pci_reset_secondary_bus() which
is now performed by pci_bridge_wait_for_secondary_bus(). A static
delay this long is only necessary for Conventional PCI, so modern
PCIe systems benefit from shorter reset times as a side effect.
Fixes: 6b2f1351af ("PCI: Wait for device to become ready after secondary bus reset")
Link: https://lore.kernel.org/r/da77c92796b99ec568bd070cbe4725074a117038.1673769517.git.lukas@wunner.de
Reported-by: Sheng Bi <windy.bi.enflame@gmail.com>
Tested-by: Ravi Kishore Koppuravuri <ravi.kishore.koppuravuri@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ab90950985 ]
On s390 PCI functions may be hotplugged individually even when they
belong to a multi-function device. In particular on an SR-IOV device VFs
may be removed and later re-added.
In commit a50297cf82 ("s390/pci: separate zbus creation from
scanning") it was missed however that struct pci_bus and struct
zpci_bus's resource list retained a reference to the PCI functions MMIO
resources even though those resources are released and freed on
hot-unplug. These stale resources may subsequently be claimed when the
PCI function re-appears resulting in use-after-free.
One idea of fixing this use-after-free in s390 specific code that was
investigated was to simply keep resources around from the moment a PCI
function first appeared until the whole virtual PCI bus created for
a multi-function device disappears. The problem with this however is
that due to the requirement of artificial MMIO addreesses (address
cookies) extra logic is then needed to keep the address cookies
compatible on re-plug. At the same time the MMIO resources semantically
belong to the PCI function so tying their lifecycle to the function
seems more logical.
Instead a simpler approach is to remove the resources of an individually
hot-unplugged PCI function from the PCI bus's resource list while
keeping the resources of other PCI functions on the PCI bus untouched.
This is done by introducing pci_bus_remove_resource() to remove an
individual resource. Similarly the resource also needs to be removed
from the struct zpci_bus's resource list. It turns out however, that
there is really no need to add the MMIO resources to the struct
zpci_bus's resource list at all and instead we can simply use the
zpci_bar_struct's resource pointer directly.
Fixes: a50297cf82 ("s390/pci: separate zbus creation from scanning")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20230306151014.60913-2-schnelle@linux.ibm.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2b9b123cc ]
Wangxun has verified there is no peer-to-peer between functions for the
below selection of SFxxx, RP1000 and RP2000 NICS. They may be
multi-function devices, but the hardware does not advertise ACS capability.
Add an ACS quirk for these devices so the functions can be in independent
IOMMU groups.
Link: https://lore.kernel.org/r/20230207102419.44326-1-mengyuanlou@net-swift.com
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9db0b9b6a1 ]
A PCI bridge may reside on a bus with other devices as well. The resource
distribution code does not take this into account and therefore it expands
the bridge resource windows too much, not leaving space for the other
devices (or functions of a multifunction device). This leads to an issue
that Jonathan reported when running QEMU with the following topology (QEMU
parameters):
-device pcie-root-port,port=0,id=root_port13,chassis=0,slot=2 \
-device x3130-upstream,id=sw1,bus=root_port13,multifunction=on \
-device e1000,bus=root_port13,addr=0.1 \
-device xio3130-downstream,id=fun1,bus=sw1,chassis=0,slot=3 \
-device e1000,bus=fun1
The first e1000 NIC here is another function in the switch upstream port.
This leads to following errors:
pci 0000:00:04.0: bridge window [mem 0x10200000-0x103fffff] to [bus 02-04]
pci 0000:02:00.0: bridge window [mem 0x10200000-0x103fffff] to [bus 03-04]
pci 0000:02:00.1: BAR 0: failed to assign [mem size 0x00020000]
e1000 0000:02:00.1: can't ioremap BAR 0: [??? 0x00000000 flags 0x0]
Fix this by taking into account bridge windows, device BARs and SR-IOV PF
BARs on the bus (PF BARs include space for VF BARS so only account PF
BARs), including the ones belonging to bridges themselves if it has any.
Link: https://lore.kernel.org/linux-pci/20221014124553.0000696f@huawei.com/
Link: https://lore.kernel.org/linux-pci/6053736d-1923-41e7-def9-7585ce1772d9@ixsystems.com/
Link: https://lore.kernel.org/r/20230131092405.29121-3-mika.westerberg@linux.intel.com
Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reported-by: Alexander Motin <mav@ixsystems.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08f0a15ee8 ]
After division the extra resource space per hotplug bridge may not be
aligned according to the window alignment, so align it before passing it
down for further distribution.
Link: https://lore.kernel.org/r/20230131092405.29121-2-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b3517f88f ]
Except for isochronous-configured devices, software may set
Max_Read_Request_Size (MRRS) to any value up to 4096. If a device issues a
read request with size greater than the completer's Max_Payload_Size (MPS),
the completer is required to break the response into multiple completions.
Instead of correctly responding with multiple completions to a large read
request, some LS7A Root Ports respond with a Completer Abort. To prevent
this, the MRRS must be limited to an implementation-specific value.
The OS cannot detect that value, so rely on BIOS to configure MRRS before
booting, and quirk the Root Ports so we never set an MRRS larger than that
BIOS value for any downstream device.
N.B. Hot-added devices are not configured by BIOS, and they power up with
MRRS = 512 bytes, so these devices will be limited to 512 bytes. If the
LS7A limit is smaller, those hot-added devices may not work correctly, but
per [1], hotplug is not supported with this chipset revision.
[1] https://lore.kernel.org/r/073638a7-ae68-2847-ac3d-29e5e760d6af@loongson.cn
[bhelgaas: commit log]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216884
Link: https://lore.kernel.org/r/20230201043018.778499-3-chenhuacai@loongson.cn
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bjorn Helgaas
Rick Wertenbroek
Xiaowei Bao
Frank Li
Serge Semin
Ilpo Järvinen
Wu Zongyong
Daire McNamara
Igor Mammedov
Sumit Gupta
Damien Le Moal
Manivannan Sadhasivam
Robin Murphy
Ondrej Zary
Junyan Ye
Rongguang Wei
Ding Hui
Nirmal Patel
Siddharth Vadapalli
Dexuan Cui
Kuppuswamy Sathyanarayanan
H. Nikolaus Schaller
Lukas Wunner
Kai-Heng Feng
Niklas Schnelle
Mengyuan Lou
Huacai Chen
Mika Westerberg