As we have already detected something attached to the chip during
initialisation, always report the LVDS connector status as connected
during probing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The IPS driver is designed to be able to run detached from i915 and
just not enable GPU turbo in that case, in order to avoid module
dependencies between the two drivers. This means that we don't know
what the load order between the two is going to be, and we had
previously only supported IPS after (optionally) i915, but not i915
after IPS. If the wrong order was chosen, you'd get no GPU turbo, and
something like half the possible graphics performance.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
It's required by the specs, but we don't know why. Let's not find out
why.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Always useful to know just which connector was polled and had its
status updated.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We were using the lockup struct from the wrong union.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On resume, we were attemping to unblank the displays before the
timing and plls had be reprogrammed which led to atom timeouts
waiting for things that are not yet programmed. Re-program
the mode first, then reset the dpms state.
This fixes the infamous atombios timeouts on resume.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes module reloading and resume as the gfx block seems to
be left in a bad state in some cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only reset the grbm blocks, srbm tends to lock the GPU
if not done properly and in most cases is not necessary.
Also, no need to call asic init after reset the grbm blocks.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 541cc96691.
Wei Yonjun reported this caused a regression against Intel VGA hotplug
on his G33 hw.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Without this, we attempt the handover too late, the firmware fb
might be accessing the chip simultaneously to us re-initializing
various parts of it, which might frighten babies or cause all sort
of nasty psychologic trauma to kitten.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[danvet: add cc: stable, forward ported and compile-fixed for X86]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[airlied: move to even earlier in module load.]
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make sure vram changes hit memory. This mirrors the
6xx/7xx behavior.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are too many strange corner cases triggered in old userspace
drivers out there to that it's nearly impossible to not break some
obscure app.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Seems to cause problems on certain laptops
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=24462
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Tested-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-fixes' of /ssd/git/drm-next:
drm/i915/bios: Reverse order of 100/120 Mhz SSC clocks
agp/intel: Fix missed cached memory flags setting in i965_write_entry()
drm/i915/sdvo: Only use the SDVO pin if it is in the valid range
drm/i915/ringbuffer: Handle wrapping of the autoreported HEAD
drm/i915/dp: Fix I2C/EDID handling with active DisplayPort to DVI converter
Fixes the lack of output on the LVDS panel of the Lenovo U160.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31596
Reported-and-tested-by: Dirk Gouders <gouders@et.bocholt.fh-gelsenkirchen.de>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
BIOSes. Can't live without them (apparently), definitely can't live with
them.
Reported-by: Ben Gamari <bgamari@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=24312
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the tail advances beyond the autoreport HEAD value, then we need to
fallback to an uncached read of the HEAD register in order to ascertain
the correct amount of remaining space in the ringbuffer.
Reported-by: Fang, Xun <xunx.fang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32259
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
It should be required for all 7xx asics, but seems to cause
problems on some AGP 7xx chips.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=19002
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Reported-and-Tested-by: Duncan <1i5t5.duncan@cox.net>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The "e" pointer is either NULL or freed when we call
drm_vblank_put(dev, e->pipe) on the error path. Just pass the "pipe"
variable directly instead.
I changed another caller to use "pipe" as well for consistency.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Grub doesn't parse spaces in parameters correctly, so
this makes it impossible to force video= parameters
for kms on the grub kernel command line.
v2: shorten the names to make them easier to type.
Reported-by: Sergej Pupykin <ml@sergej.pp.ru>
Cc: Sergej Pupykin <ml@sergej.pp.ru>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DisplayPort standard (1.1a) states that:
The I2C-over-AUX Reply field is valid only when Native AUX CH Reply
field is AUX_ACK (00). When Native AUX CH Reply field is not 00, then,
I2C-over-AUX Reply field must be 00 and be ignored.
This fixes broken EDID reading when using an active DisplayPort to
duallink DVI converter. If the AUX CH replier chooses to defer the
transaction, a short read occurs and erroneous data is returned as
the i2c reply due to a lack of length checking and failure to check
for AUX ACK.
As a result, broken EDIDs can look like:
0 1 2 3 4 5 6 7 8 9 a b c d e f 0123456789abcdef
00: bc bc bc ff bc bc bc ff bc bc bc ac bc bc bc 45 ???.???.???????E
10: bc bc bc 10 bc bc bc 34 bc bc bc ee bc bc bc 4c ???????4???????L
20: bc bc bc 50 bc bc bc 00 bc bc bc 40 bc bc bc 00 ???P???.???@???.
30: bc bc bc 01 bc bc bc 01 bc bc bc a0 bc bc bc 40 ???????????????@
40: bc bc bc 00 bc bc bc 00 bc bc bc 00 bc bc bc 55 ???.???.???.???U
50: bc bc bc 35 bc bc bc 31 bc bc bc 20 bc bc bc fc ???5???1??? ????
60: bc bc bc 4c bc bc bc 34 bc bc bc 46 bc bc bc 00 ???L???4???F???.
70: bc bc bc 38 bc bc bc 11 bc bc bc 20 bc bc bc 20 ???8??????? ???
80: bc bc bc ff bc bc bc ff bc bc bc ff bc bc bc ff ???.???.???.???.
...
which can lead to:
[drm:drm_edid_block_valid] *ERROR* EDID checksum is invalid, remainder
[drm:drm_edid_block_valid] *ERROR* Raw EDID:
<3>30 30 30 30 30 30 30 32 38 32 30 32 63 63 31 61 000000028202cc1a
<3>28 00 02 8c 00 00 00 00 18 00 00 00 00 00 00 00 (...............
<3>20 4c 61 73 74 20 62 65 61 63 6f 6e 3a 20 33 32 Last beacon: 32
<3>32 30 6d 73 20 61 67 6f 46 00 05 8c 00 00 00 00 20ms agoF.......
<3>36 00 00 00 00 00 00 00 00 0c 57 69 2d 46 69 20 6.........Wi-Fi
<3>52 6f 75 74 65 72 01 08 82 84 8b 96 24 30 48 6c Router......$0Hl
<3>03 01 01 06 02 00 00 2a 01 00 2f 01 00 32 04 0c .......*../..2..
<3>12 18 60 dd 09 00 10 18 02 00 00 01 00 00 18 00 ..`.............
Signed-off-by: David Flynn <davidf@rd.bbc.co.uk>
[ickle: fix up some surrounding checkpatch warnings]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Avoid overflowing a 32 bit value.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Forbid allocating buffer bigger than visible VRAM or GTT, also
properly set lpfn field.
v2 - use max macro
- silence warning
v3 - don't explicitly set range limit
- use min macro
Cc: stable <stable@kernel.org>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Prevents code that assumes that the encoder is active when asked to be
disabled from dying a horrible death.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kristian Høgsberg <krh@bitplanet.net>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
As we may try to power down the link at various times, it is not
necessarily still coupled with an encoder and so we must be careful not
to depend upon an operation that is only valid when the link is still
attached to a pipe.
Fixes regression in 5bddd17.
Reported-and-tested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org [after applying 5bddd17]
In order for bos to retire eventually, a request must be sent down the
ring. This is expected, for example, by occlusion queries for which mesa
will wait upon (whilst running glean) before issuing more batches and so
the normal activity upon the ring is suspended and we need to emit a
request to clear the idle ring.
Reported-by: Jinjin, Wang <jinjin.wang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30380
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Linus Torvalds pointed out that our code was unbalanced when powering on
the panel with respect to the power off sequence in that we were failing
to restore the panel-fitter. The consequence of this would be that
across a simple DPMS off/on for a non-native mode, without an intervening
modeset, the panel fitter would remain disabled and the output would shift
on the panel.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There's not much we can do here but hope for the best. However the first
failure happens quite frequently and if often remedied by the second
attempt to reset HEAD. So only print the error if that attempt also
fails.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=19802
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Otherwise we can't really fix the abi-braindeadness of forcing
libva to manually wait for rendering when switching rings. Which
in turn makes implementing hw semaphores a pointless exercise
(at least for ironlake).
[Also added the relaxed fencing param to explain the jump in
numbering - relaxed fencing is in -next.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Fixes the modesetting on the secondary panel of the Libretto W100 and
presumably many more Ironlake laptops with SDVO LVDS displays.
Reported-and-tested-by: Matthew Willoughby <mattfredwill@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Use the hardware DDA to calculate the ratio with as much accuracy as is
possible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
If we leave the registers in a conflicting state then when we attempt
to teardown the active mode, we will not disable the pipes and planes
in the correct order -- leaving a plane reading from a disabled pipe and
possibly leading to undefined behaviour.
Reported-and-tested-by: Andy Whitcroft <apw@canonical.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32078
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
This workaround only applies to Ironlake.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
The pipe is always set to 8BPC, but here we were leaving whatever
previous bits were set by the BIOS in place.
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
6xx/7xx was hitting the wrong BUS_CNTL reg and bits.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-fixes' of /ssd/git/drm-next:
Revert "drm/i915/dp: use VBT provided eDP params if available"
drm/i915: Clear pfit registers when not used by any outputs
drm/i915: fix regression due to ba3d8d749b
This reverts commit 869184a675.
This is required for the Sony Vaio Jesse was working on at the time, but
breaks most other eDP machines - machines that were working in earlier
kernels.
Reported-and-tested-by: Dave Airlie <airlied@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31188
Tested-by: Zhao Jian <jian.j.zhao@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... otherwise the panel-fitter may be left enabled with random settings
and cause unintended filtering (i.e. blurring of native modes on external
panels).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31942
Reported-and-tested-by: Ben Kohler <bkohler@gmail.com>
Tested-by: Ciprian Docan <docan@eden.rutgers.edu>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In order to correctly report monitor connected status changes, the
previous monitor status must be recorded in the connector->status
value instead of being discarded.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When setting a new crtc configuration, force the DPMS state of all
connectors to ON. Otherwise, they'll be left at OFF and a future mode set
that disables the specified connector will not turn the connector off.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We don't track gpu flush request in any special way. So even with
obj->write_domain == 0, a gpu flush might be outstanding but no
yet executed. Even worse, the latest request might use the object
only for reading. So and unconditional call to object_wait_rendering
is needed for !pipelined.
Hence revert that patch fully and untangle the flushing from the
synchronization again.
Reported-by: Keith Packard <keithp@keithp.com>
Tested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Chris Wilson
Eric Anholt
Alex Deucher
Dave Airlie
Benjamin Herrenschmidt
Dan Carpenter
David Flynn
Jerome Glisse
Daniel Vetter
Keith Packard