The various types of tunnels running over IPv4 can ask to set the DF
bit to do PMTU discovery. However, PMTU discovery is subject to the
threshold set by the net.ipv4.route.min_pmtu sysctl, and is also
disabled on routes with "mtu lock". In those cases, we shouldn't set
the DF bit.
This patch makes setting the DF bit conditional on the route's MTU
locking state.
This issue seems to be older than git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No changes in refcount semantics -- key init is false; replace
static_key_slow_inc|dec with static_branch_inc|dec
static_key_false with static_branch_unlikely
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switches and modern SR-IOV enabled NICs may multiplex traffic from Port
representators and control messages over single set of hardware queues.
Control messages and muxed traffic may need ordered delivery.
Those requirements make it hard to comfortably use TC infrastructure today
unless we have a way of attaching metadata to skbs at the upper device.
Because single set of queues is used for many netdevs stopping TC/sched
queues of all of them reliably is impossible and lower device has to
retreat to returning NETDEV_TX_BUSY and usually has to take extra locks on
the fastpath.
This patch attempts to enable port/representative devs to attach metadata
to skbs which carry port id. This way representatives can be queueless and
all queuing can be performed at the lower netdev in the usual way.
Traffic arriving on the port/representative interfaces will be have
metadata attached and will subsequently be queued to the lower device for
transmission. The lower device should recognize the metadata and translate
it to HW specific format which is most likely either a special header
inserted before the network headers or descriptor/metadata fields.
Metadata is associated with the lower device by storing the netdev pointer
along with port id so that if TC decides to redirect or mirror the new
netdev will not try to interpret it.
This is mostly for SR-IOV devices since switches don't have lower netdevs
today.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass extack arg down to lwtunnel_build_state and the build_state callbacks.
Add messages for failures in lwtunnel_build_state, and add the extarg to
nla_parse where possible in the build_state callbacks.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the new extended ACK reporting struct to all of the generic
netlink parsing functions. For now, pass NULL in almost all callers
(except for some in the core.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing about lwt state requires a device reference, so remove the
input argument.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modules implementing lwtunnel ops should not be allowed to unload
while there is state alive using those ops, so specify the owning
module for all lwtunnel ops.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some configurations (e.g. geneve interface with default
MTU of 1500 over an ethernet interface with 1500 MTU) result
in the transmission of packets that exceed the configured MTU.
While this should be considered to be a "bad" configuration,
it is still allowed and should not result in the sending
of packets that exceed the configured MTU.
Fix by dropping the assumption in ip_finish_output_gso() that
locally originated gso packets will never need fragmentation.
Basic testing using iperf (observing CPU usage and bandwidth)
have shown no measurable performance impact for traffic not
requiring fragmentation.
Fixes: c7ba65d7b6 ("net: ip: push gso skb forwarding handling down the stack")
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb has a valid l4 hash, there is no point clearing hash and force
a further flow dissection when a tunnel encapsulation is added.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In b8247f095e,
"net: ip_finish_output_gso: If skb_gso_network_seglen exceeds MTU, allow segmentation for local udp tunneled skbs"
gso skbs arriving from an ingress interface that go through UDP
tunneling, are allowed to be fragmented if the resulting encapulated
segments exceed the dst mtu of the egress interface.
This aligned the behavior of gso skbs to non-gso skbs going through udp
encapsulation path.
However the non-gso vs gso anomaly is present also in the following
cases of a GRE tunnel:
- ip_gre in collect_md mode, where TUNNEL_DONT_FRAGMENT is not set
(e.g. OvS vport-gre with df_default=false)
- ip_gre in nopmtudisc mode, where IFLA_GRE_IGNORE_DF is set
In both of the above cases, the non-gso skbs get fragmented, whereas the
gso skbs (having skb_gso_network_seglen that exceeds dst mtu) get dropped,
as they don't go through the segment+fragment code path.
Fix: Setting IPSKB_FRAG_SEGS if the tunnel specified IP_DF bit is NOT set.
Tunnels that do set IP_DF, will not go to fragmentation of segments.
This preserves behavior of ip_gre in (the default) pmtudisc mode.
Fixes: b8247f095e ("net: ip_finish_output_gso: If skb_gso_network_seglen exceeds MTU, allow segmentation for local udp tunneled skbs")
Reported-by: wenxu <wenxu@ucloud.cn>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Tested-by: wenxu <wenxu@ucloud.cn>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given:
- tap0 and vxlan0 are bridged
- vxlan0 stacked on eth0, eth0 having small mtu (e.g. 1400)
Assume GSO skbs arriving from tap0 having a gso_size as determined by
user-provided virtio_net_hdr (e.g. 1460 corresponding to VM mtu of 1500).
After encapsulation these skbs have skb_gso_network_seglen that exceed
eth0's ip_skb_dst_mtu.
These skbs are accidentally passed to ip_finish_output2 AS IS.
Alas, each final segment (segmented either by validate_xmit_skb or by
hardware UFO) would be larger than eth0 mtu.
As a result, those above-mtu segments get dropped on certain networks.
This behavior is not aligned with the NON-GSO case:
Assume a non-gso 1500-sized IP packet arrives from tap0. After
encapsulation, the vxlan datagram is fragmented normally at the
ip_finish_output-->ip_fragment code path.
The expected behavior for the GSO case would be segmenting the
"gso-oversized" skb first, then fragmenting each segment according to
dst mtu, and finally passing the resulting fragments to ip_finish_output2.
'ip_finish_output_gso' already supports this "Slowpath" behavior,
according to the IPSKB_FRAG_SEGS flag, which is only set during ipv4
forwarding (not set in the bridged case).
In order to support the bridged case, we'll mark skbs arriving from an
ingress interface that get udp-encaspulated as "allowed to be fragmented",
causing their network_seglen to be validated by 'ip_finish_output_gso'
(and fragment if needed).
Note the TUNNEL_DONT_FRAGMENT tun_flag is still honoured (both in the
gso and non-gso cases), which serves users wishing to forbid
fragmentation at the udp tunnel endpoint.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add encap_hlen and ip_tunnel_encap structure to ip6_tnl. Add functions
for getting encap hlen, setting up encap on a tunnel, performing
encapsulation operation.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate all the ip_tunnel_encap definitions in one spot in the
header file. Also, move ip_encap_hlen and ip_tunnel_encap from
ip_tunnel.c to ip_tunnels.h so they call be called without a dependency
on ip_tunnel module. Similarly, move iptun_encaps to ip_tunnel_core.c.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Locally generated TCP GSO packets having to go through a GRE/SIT/IPIP
tunnel have to go through an expensive skb_unclone()
Reallocating skb->head is a lot of work.
Test should really check if a 'real clone' of the packet was done.
TCP does not care if the original gso_type is changed while the packet
travels in the stack.
This adds skb_header_unclone() which is a variant of skb_clone()
using skb_header_cloned() check instead of skb_cloned().
This variant can probably be used from other points.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_data() is now aligned on a 64-bit area.
A temporary version (nla_put_be64_32bit()) is added for nla_put_net64().
This function is removed in the next patch.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the IP tunnel core function iptunnel_handle_offloads so
that we return an int and do not free the skb inside the function. This
actually allows us to clean up several paths in several tunnels so that we
can free the skb at one point in the path without having to have a
secondary path if we are supporting tunnel offloads.
In addition it should resolve some double-free issues I have found in the
tunnels paths as I believe it is possible for us to end up triggering such
an event in the case of fou or gue.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow calling of iptunnel_pull_header without special casing ETH_P_TEB inner
protocol.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since nla_get_in_addr and nla_put_in_addr were implemented,
so use them appropriately.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a route with IPv6 encapsulation, the traffic class and hop limit
values are interchanged when returned to userspace by the kernel.
For example, see below.
># ip route add 192.168.0.1 dev eth0.2 encap ip6 dst 0x50 tc 0x50 hoplimit 100 table 1000
># ip route show table 1000
192.168.0.1 encap ip6 id 0 src :: dst fe83::1 hoplimit 80 tc 100 dev eth0.2 scope link
Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a packet is either locally encapsulated or processed through GRO
it is marked with the offloads that it requires. However, when it is
decapsulated these tunnel offload indications are not removed. This
means that if we receive an encapsulated TCP packet, aggregate it with
GRO, decapsulate, and retransmit the resulting frame on a NIC that does
not support encapsulation, we won't be able to take advantage of hardware
offloads even though it is just a simple TCP packet at this point.
This fixes the problem by stripping off encapsulation offload indications
when packets are decapsulated.
The performance impacts of this bug are significant. In a test where a
Geneve encapsulated TCP stream is sent to a hypervisor, GRO'ed, decapsulated,
and bridged to a VM performance is improved by 60% (5Gbps->8Gbps) as a
result of avoiding unnecessary segmentation at the VM tap interface.
Reported-by: Ramu Ramamurthy <sramamur@linux.vnet.ibm.com>
Fixes: 68c33163 ("v4 GRE: Add TCP segmentation offload for GRE")
Signed-off-by: Jesse Gross <jesse@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
eBPF defines this as BPF_TUNLEN_MAX and OVS just uses the hard-coded
value inside struct sw_flow_key. Thus, add and use IP_TUNNEL_OPTS_MAX
for this, which makes the code a bit more generic and allows to remove
BPF_TUNLEN_MAX from eBPF code.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of skb_scrub_packet was open coded in iptunnel_pull_header. Let it call
skb_scrub_packet directly instead.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users now pass false, so we can remove it, and remove the code that
was conditional upon it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The arithmetic properties of the ones-complement checksum mean that a
correctly checksummed inner packet, including its checksum, has a ones
complement sum depending only on whatever value was used to initialise
the checksum field before checksumming (in the case of TCP and UDP,
this is the ones complement sum of the pseudo header, complemented).
Consequently, if we are going to offload the inner checksum with
CHECKSUM_PARTIAL, we can compute the outer checksum based only on the
packed data not covered by the inner checksum, and the initial value of
the inner checksum field.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate endianness mismatch warnings (reported by sparse) in this file by
using appropriate nla_put_*()/nla_get_*() calls.
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By moving stats update into iptunnel_xmit(), we can simplify
iptunnel_xmit() usage. With this change there is no need to
call another function (iptunnel_xmit_stats()) to update stats
in tunnel xmit code path.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like many files are including mroute.h unnecessarily, so remove
the include. Most importantly remove it from ipv6.
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store net in a variable in ip_tunnel_xmit so it does not need
to be recomputed when it is used again.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is confusing and silly hiding a parameter so modify all of
the callers to pass in the appropriate socket or skb->sk if
no socket is known.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP tunnel config is asymmetric wrt. to the ports used. The source and
destination ports from one direction of the tunnel are not related to the
ports of the other direction. We need to be able to respond to ARP requests
using the correct ports without involving routing.
As the consequence, UDP ports need to be fixed property of the tunnel
interface and cannot be set per route. Remove the ability to set ports per
route. This is still okay to do, as no kernel has been released with these
attributes yet.
Note that the ability to specify source and destination ports is preserved
for other users of the lwtunnel API which don't use routes for tunnel key
specification (like openvswitch).
If in the future we rework ARP handling to allow port specification, the
attributes can be added back.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using ip lwtunnels, the additional data for xmit (basically, the actual
tunnel to use) are carried in ip_tunnel_info either in dst->lwtstate or in
metadata dst. When replying to ARP requests, we need to send the reply to
the same tunnel the request came from. This means we need to construct
proper metadata dst for ARP replies.
We could perform another route lookup to get a dst entry with the correct
lwtstate. However, this won't always ensure that the outgoing tunnel is the
same as the incoming one, and it won't work anyway for IPv4 duplicate
address detection.
The only thing to do is to "reverse" the ip_tunnel_info.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was already done a long time ago in
commit 64194c31a0 ("inet: Make tunnel RX/TX byte counters more consistent")
but tx path was broken (at least since 3.10).
Before the patch the gre header was included on tx.
After the patch:
$ ping -c1 192.168.0.121 ; ip -s l ls dev gre1
PING 192.168.0.121 (192.168.0.121) 56(84) bytes of data.
64 bytes from 192.168.0.121: icmp_req=1 ttl=64 time=2.95 ms
--- 192.168.0.121 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 2.955/2.955/2.955/0.000 ms
7: gre1@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1468 qdisc noqueue state UNKNOWN mode DEFAULT group default
link/gre 10.16.0.249 peer 10.16.0.121
RX: bytes packets errors dropped overrun mcast
84 1 0 0 0 0
TX: bytes packets errors dropped carrier collsns
84 1 0 0 0 0
Reported-by: Julien Meunier <julien.meunier@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tun-info options pointer is used in few cases to
pass options around. But tunnel options can be accessed using
ip_tunnel_info_opts() API without using the pointer. Following
patch removes the redundant pointer and consistently make use
of API.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's currently nothing preventing directing packets with IPv6
encapsulation data to IPv4 tunnels (and vice versa). If this happens,
IPv6 addresses are incorrectly interpreted as IPv4 ones.
Track whether the given ip_tunnel_key contains IPv4 or IPv6 data. Store this
in ip_tunnel_info. Reject packets at appropriate places if they are supposed
to be encapsulated into an incompatible protocol.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cfg and family arguments to lwt build state functions. cfg is a void
pointer and will either be a pointer to a fib_config or fib6_config
structure. The family parameter indicates which one (either AF_INET
or AF_INET6).
LWT encpasulation implementation may use the fib configuration to build
the LWT state.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow specification of per route IP tunnel instructions also for IPv6.
This complements commit 3093fbe7ff ("route: Per route IP tunnel metadata
via lightweight tunnel").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
CC: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the ipv4_tos and ipv4_ttl fields to just 'tos' and 'ttl', as they'll
be used with IPv6 tunnels, too.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the IPv6 addresses as an union with IPv4 ones. When using IPv4, the
newly introduced padding after the IPv4 addresses needs to be zeroed out.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, two routes going through the same tunnel interface are considered
the same even when they are routed to a different host after encapsulation.
This causes all routes added after the first one to have incorrect
encapsulation parameters.
This is nicely visible by doing:
# ip r a 192.168.1.2/32 dev vxlan0 tunnel dst 10.0.0.2
# ip r a 192.168.1.3/32 dev vxlan0 tunnel dst 10.0.0.3
# ip r
[...]
192.168.1.2/32 tunnel id 0 src 0.0.0.0 dst 10.0.0.2 [...]
192.168.1.3/32 tunnel id 0 src 0.0.0.0 dst 10.0.0.2 [...]
Implement the missing comparison function.
Fixes: 3093fbe7ff ("route: Per route IP tunnel metadata via lightweight tunnel")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have IFLA_IPTUN_ netlink attributes. The IP_TUN_ attributes look
very similar, yet they serve very different purpose. This is confusing for
anyone trying to implement a user space tool supporting lwt.
As the IP_TUN_ attributes are used only for the lightweight tunnels, prefix
them with LWTUNNEL_IP_ instead to make their purpose clear. Also, it's more
logical to have them in lwtunnel.h together with the encap enum.
Fixes: 3093fbe7ff ("route: Per route IP tunnel metadata via lightweight tunnel")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the module_init() to a invocation from inet_init() since
ip_tunnel_core is part of the INET built-in.
Fixes: 3093fbe7ff ("route: Per route IP tunnel metadata via lightweight tunnel")
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This add the ability to select a routing table based on the tunnel
id which allows to maintain separate routing tables for each virtual
tunnel network.
ip rule add from all tunnel-id 100 lookup 100
ip rule add from all tunnel-id 200 lookup 200
A new static key controls the collection of metadata at tunnel level
upon demand.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a new IP tunnel lightweight tunnel type which allows
to specify IP tunnel instructions per route. Only IPv4 is supported
at this point.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_dropped stat wasn't being reported when ip_tunnel_get_stats64 was
called. This was leading to some confusing results in my debug as I was
seeing rx_errors increment but no other value which pointed me toward the
type of error being seen.
This change corrects that by using netdev_stats_to_stats64 to copy all
available dev stats instead of just the few that were hand picked.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "ntohs(proto) >= ETH_P_802_3_MIN" w/ eth_proto_is_802_3(proto).
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller
Sabrina Dubroca
Michał Mirosław
Davidlohr Bueso
Jakub Kicinski
David Ahern
Johannes Berg
David Ahern
Robert Shearman
stephen hemminger
Lance Richardson
Eric Dumazet
Shmulik Ladkani
Tom Herbert
Nicolas Dichtel
Alexander Duyck
Jiri Benc
Haishuang Yan
Quentin Armitage
Jesse Gross
Daniel Borkmann
Edward Cree
Pravin B Shelar
Nikolay Aleksandrov
Eric W. Biederman
Thomas Graf
Alexander Duyck