Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Introduce configfs support for unlocked configfs_depend_item()
(krzysztof + andrezej)
- Conversion of usb-gadget target driver to new function registration
interface (andrzej + sebastian)
- Enable qla2xxx FC target mode support for Extended Logins (himansu +
giridhar)
- Enable qla2xxx FC target mode support for Exchange Offload (himansu +
giridhar)
- Add qla2xxx FC target mode irq affinity notification + selective
command queuing. (quinn + himanshu)
- Fix iscsi-target deadlock in se_node_acl configfs deletion (sagi +
nab)
- Convert se_node_acl configfs deletion + se_node_acl->queue_depth to
proper se_session->sess_kref + target_get_session() usage. (hch +
sagi + nab)
- Fix long-standing race between se_node_acl->acl_kref get and
get_initiator_node_acl() lookup. (hch + nab)
- Fix target/user block-size handling, and make sure netlink reaches
all network namespaces (sheng + andy)
Note there is an outstanding bug-fix series for remote I_T nexus port
TMR LUN_RESET has been posted and still being tested, and will likely
become post -rc1 material at this point"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (56 commits)
scsi: qla2xxxx: avoid type mismatch in comparison
target/user: Make sure netlink would reach all network namespaces
target: Obtain se_node_acl->acl_kref during get_initiator_node_acl
target: Convert ACL change queue_depth se_session reference usage
iscsi-target: Fix potential dead-lock during node acl delete
ib_srpt: Convert acl lookup to modern get_initiator_node_acl usage
tcm_fc: Convert acl lookup to modern get_initiator_node_acl usage
tcm_fc: Wait for command completion before freeing a session
target: Fix a memory leak in target_dev_lba_map_store()
target: Support aborting tasks with a 64-bit tag
usb/gadget: Remove set-but-not-used variables
target: Remove an unused variable
target: Fix indentation in target_core_configfs.c
target/user: Allow user to set block size before enabling device
iser-target: Fix non negative ERR_PTR isert_device_get usage
target/fcoe: Add tag support to tcm_fc
qla2xxx: Check for online flag instead of active reset when transmitting responses
qla2xxx: Set all queues to 4k
qla2xxx: Disable ZIO at start time.
qla2xxx: Move atioq to a different lock to reduce lock contention
...
The num_node_acls member in struct se_portal_group is modified
by several functions but is never read. Hence remove it.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
queue work element to specific process lessen cache miss
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This change sets the LBPRZ flag in EVPD page b2h and READ CAPACITY (16)
based on a new unmap_zeroes_data device attribute. This flag is set
automatically for iblock based on underlying block device queue's
discard_zeroes_data flag.
Signed-off-by: Jamie Pocas <jamie.pocas@emc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a race + use after free where the first
stage of COMPARE_AND_WRITE in compare_and_write_callback()
is rescheduled after the backend sends the secondary WRITE,
resulting in second stage compare_and_write_post() callback
completing in target_complete_ok_work() before the first
can return.
Because current code depends on checking se_cmd->se_cmd_flags
after return from se_cmd->transport_complete_callback(),
this results in first stage having SCF_COMPARE_AND_WRITE_POST
set, which incorrectly falls through into second stage CAW
processing code, eventually triggering a NULL pointer
dereference due to use after free.
To address this bug, pass in a new *post_ret parameter into
se_cmd->transport_complete_callback(), and depend upon this
value instead of ->se_cmd_flags to determine when to return
or fall through into ->queue_status() code for CAW.
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"This series contains HCH's changes to absorb configfs attribute
->show() + ->store() function pointer usage from it's original
tree-wide consumers, into common configfs code.
It includes usb-gadget, target w/ drivers, netconsole and ocfs2
changes to realize the improved simplicity, that now renders the
original include/target/configfs_macros.h CPP magic for fabric drivers
and others, unnecessary and obsolete.
And with common code in place, new configfs attributes can be added
easier than ever before.
Note, there are further improvements in-flight from other folks for
v4.5 code in configfs land, plus number of target fixes for post -rc1
code"
In the meantime, a new user of the now-removed old configfs API came in
through the char/misc tree in commit 7bd1d4093c ("stm class: Introduce
an abstraction for System Trace Module devices").
This merge resolution comes from Alexander Shishkin, who updated his stm
class tracing abstraction to account for the removal of the old
show_attribute and store_attribute methods in commit 517982229f
("configfs: remove old API") from this pull. As Alexander says about
that patch:
"There's no need to keep an extra wrapper structure per item and the
awkward show_attribute/store_attribute item ops are no longer needed.
This patch converts policy code to the new api, all the while making
the code quite a bit smaller and easier on the eyes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>"
That patch was folded into the merge so that the tree should be fully
bisectable.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (23 commits)
configfs: remove old API
ocfs2/cluster: use per-attribute show and store methods
ocfs2/cluster: move locking into attribute store methods
netconsole: use per-attribute show and store methods
target: use per-attribute show and store methods
spear13xx_pcie_gadget: use per-attribute show and store methods
dlm: use per-attribute show and store methods
usb-gadget/f_serial: use per-attribute show and store methods
usb-gadget/f_phonet: use per-attribute show and store methods
usb-gadget/f_obex: use per-attribute show and store methods
usb-gadget/f_uac2: use per-attribute show and store methods
usb-gadget/f_uac1: use per-attribute show and store methods
usb-gadget/f_mass_storage: use per-attribute show and store methods
usb-gadget/f_sourcesink: use per-attribute show and store methods
usb-gadget/f_printer: use per-attribute show and store methods
usb-gadget/f_midi: use per-attribute show and store methods
usb-gadget/f_loopback: use per-attribute show and store methods
usb-gadget/ether: use per-attribute show and store methods
usb-gadget/f_acm: use per-attribute show and store methods
usb-gadget/f_hid: use per-attribute show and store methods
...
This also allows to remove the target-specific old configfs macros, and
gets rid of the target_core_fabric_configfs.h header which only had one
function declaration left that could be moved to a better place.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Acked-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a DF_READ_ONLY flag that is used by IBLOCK to
signal when a backend has been set to read-only mode, in order
to propigate read-only status up to core_tpg_add_lun() for all
future LUN fabric exports.
With this is place, existing emulation for reporting read-only
in spc_emulate_modesense() and normal transport_lookup_cmd_lun()
TCM_WRITE_PROTECTED status checking just works as expected.
Reported-by: Joeue Deng <joeue404@gmail.com>
Reported-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
On x86-64, these changes reduce the struct size from 528 bytes to 496
bytes. We save a cacheline and get under 512 bytes for better packing.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
For every command, we set se_ordered_id by doing atomic_inc_return on
dev->dev_ordered_id for the corresponding device. However, the only
places this value gets used are in pr_debug() calls, which doesn't
seem worth an extra atomic op per IO.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
From: Chris Zankel <czankel@purestorage.com>
The initiatorname field in se_acl_lun is only a copy of the same field
in se_node_acl, so remove it and use the version in se_node_acl where
needed (it's actually only used for pr_debug)
Signed-off-by: Chris Zankel <czankel@purestorage.com>
Signed-off-by: Spencer Baugh <spencer.baugh@purestorage.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The lun_flags field is not used, so drop it.
Signed-off-by: Chris Zankel <czankel@purestorage.com>
Signed-off-by: Spencer Baugh <spencer.baugh@purestorage.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Its not a good idea to keep target specific definition of
the same t10-pi tuple.
(Fix v4.2-rc1 patch fuzz - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"It's been a busy development cycle for target-core in a number of
different areas.
The fabric API usage for se_node_acl allocation is now within
target-core code, dropping the external API callers for all fabric
drivers tree-wide.
There is a new conversion to RCU hlists for se_node_acl and
se_portal_group LUN mappings, that turns fast-past LUN lookup into a
completely lockless code-path. It also removes the original
hard-coded limitation of 256 LUNs per fabric endpoint.
The configfs attributes for backends can now be shared between core
and driver code, allowing existing drivers to use common code while
still allowing flexibility for new backend provided attributes.
The highlights include:
- Merge sbc_verify_dif_* into common code (sagi)
- Remove iscsi-target support for obsolete IFMarker/OFMarker
(Christophe Vu-Brugier)
- Add bidi support in target/user backend (ilias + vangelis + agover)
- Move se_node_acl allocation into target-core code (hch)
- Add crc_t10dif_update common helper (akinobu + mkp)
- Handle target-core odd SGL mapping for data transfer memory
(akinobu)
- Move transport ID handling into target-core (hch)
- Move task tag into struct se_cmd + support 64-bit tags (bart)
- Convert se_node_acl->device_list[] to RCU hlist (nab + hch +
paulmck)
- Convert se_portal_group->tpg_lun_list[] to RCU hlist (nab + hch +
paulmck)
- Simplify target backend driver registration (hch)
- Consolidate + simplify target backend attribute implementations
(hch + nab)
- Subsume se_port + t10_alua_tg_pt_gp_member into se_lun (hch)
- Drop lun_sep_lock for se_lun->lun_se_dev RCU usage (hch + nab)
- Drop unnecessary core_tpg_register TFO parameter (nab)
- Use 64-bit LUNs tree-wide (hannes)
- Drop left-over TARGET_MAX_LUNS_PER_TRANSPORT limit (hannes)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (76 commits)
target: Bump core version to v5.0
target: remove target_core_configfs.h
target: remove unused TARGET_CORE_CONFIG_ROOT define
target: consolidate version defines
target: implement WRITE_SAME with UNMAP bit using ->execute_unmap
target: simplify UNMAP handling
target: replace se_cmd->execute_rw with a protocol_data field
target/user: Fix inconsistent kmap_atomic/kunmap_atomic
target: Send UA when changing LUN inventory
target: Send UA upon LUN RESET tmr completion
target: Send UA on ALUA target port group change
target: Convert se_lun->lun_deve_lock to normal spinlock
target: use 'se_dev_entry' when allocating UAs
target: Remove 'ua_nacl' pointer from se_ua structure
target_core_alua: Correct UA handling when switching states
xen-scsiback: Fix compile warning for 64-bit LUN
target: Remove TARGET_MAX_LUNS_PER_TRANSPORT
target: use 64-bit LUNs
target: Drop duplicate + unused se_dev_check_wce
target: Drop unnecessary core_tpg_register TFO parameter
...
Instead of leaking this SBC read/write implementation detail just add an
opaqueue protocol specific pointer to struct se_cmd that we can assign
the sbc_ops vector to.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
LUN allocation is now fully dynamic, so there is no need to
artificially restrain the number of exported LUNs.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As we're now using a list to hold the LUNs the target core
can now converted to use 64-bit LUNs internally.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Only include SCSI initiator header files in target code that needs
these header files, namely the SCSI pass-through code and the tcm_loop
driver. Change SCSI_SENSE_BUFFERSIZE into TRANSPORT_SENSE_BUFFER in
target code because the former is intended for initiator code and the
latter for target code. With this patch the only initiator include
directives in target code that remain are as follows:
$ git grep -nHE 'include .scsi/(scsi.h|scsi_host.h|scsi_device.h|scsi_cmnd.h)' drivers/target drivers/infiniband/ulp/{isert,srpt} drivers/usb/gadget/legacy/tcm_*.[ch] drivers/{vhost,xen} include/{target,trace/events/target.h}
drivers/target/loopback/tcm_loop.c:29:#include <scsi/scsi.h>
drivers/target/loopback/tcm_loop.c:31:#include <scsi/scsi_host.h>
drivers/target/loopback/tcm_loop.c:32:#include <scsi/scsi_device.h>
drivers/target/loopback/tcm_loop.c:33:#include <scsi/scsi_cmnd.h>
drivers/target/target_core_pscsi.c:39:#include <scsi/scsi_device.h>
drivers/target/target_core_pscsi.c:40:#include <scsi/scsi_host.h>
drivers/xen/xen-scsiback.c:52:#include <scsi/scsi_host.h> /* SG_ALL */
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Correct the comment above the definition of TCM_MAX_COMMAND_SIZE.
A quote from Christoph:
There aren't any legacy issues, we just decided to handle >
16 byte CDBs in the slow path.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
With se_port_t and t10_alua_tg_pt_gp_member being absored into se_lun,
there is no need for an extra atomic_t based reference count for PR
ALL_TG_PT=1 and ALUA access state transition.
Go ahead and use the existing percpu se_lun->lun_ref instead, and
convert the two special cases to percpu_ref_tryget_live() to avoid
se_lun if transport_clear_lun_ref() has already been invoked to
shutdown the se_lun.
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
With se_port and t10_alua_tg_pt_gp_member being absored into se_lun,
there is no need for an extra lock to protect se_lun->lun_se_dev
assignment.
This patch also converts backend drivers to use call_rcu() release
to allow any se_device readers to complete. The call_rcu() instead
of kfree_rcu() is required here because se_device is embedded into
the backend driver specific structure.
Also, convert se_lun->lun_stats to use atomic_long_t within the
target_complete_ok_work() completion callback, and add FIXME for
transport_lookup_tmr_lun() with se_lun->lun_ref.
Finally, update sbp_update_unit_directory() special case usage with
proper rcu_dereference_raw() and configfs symlink comment.
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Chris Boot <bootc@bootc.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch eliminates all se_port + t10_alua_tg_pt_gp_member usage,
and converts current users to direct se_lun pointer dereference.
This includes the removal of core_export_port(), core_release_port()
core_dev_export() and core_dev_unexport(). Along with conversion
of special case se_lun pointer dereference within PR ALL_TG_PT=1
and ALUA access state transition UNIT_ATTENTION handling.
Also, update core_enable_device_list_for_node() to reference the
new per se_lun->lun_deve_list when creating a new entry, or
replacing an existing one via RCU.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of starting a thread from transport_clear_lun_ref() that
waits for LUN shutdown, wait in that function for LUN shutdown
to finish. Additionally, change the return type of
transport_clear_lun_ref() from int to void.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Rewrite the backend driver registration based on what we did to the fabric
drivers: introduce a read-only struct target_bakckend_ops that the driver
registers, which is then instanciate as a struct target_backend by the
core. This allows the ops vector to be smaller and allows us to mark it
const. At the same time the registration function can set up the
configfs attributes, avoiding the need to add additional boilerplate code
for that to the drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that se_portal_group->tpg_lun_hlist is a RCU protected hlist,
go ahead and drop the left-over lun->lun_status usage.
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts se_tpg->acl_node_lock to struct mutex, so that
->acl_node_acl walkers in core_clear_lun_from_tpg() can block when
calling core_disable_device_list_for_node().
It also updates core_dev_add_lun() to hold ->acl_node_mutex when
calling core_tpg_add_node_to_devs() to build ->lun_entry_hlist
for dynamically generated se_node_acl.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts the fixed size se_portal_group->tpg_lun_list[]
to use modern RCU with hlist_head in order to support an arbitary
number of se_lun ports per target endpoint.
It includes dropping core_tpg_alloc_lun() from core_dev_add_lun(),
and calling it directly from target_fabric_make_lun() to allocate
a new se_lun. And add a new target_fabric_port_release() configfs
item callback to invoke kfree_rcu() to release memory during
se_lun->lun_group shutdown.
Also now that se_node_acl->lun_entry_hlist is using RCU, convert
existing tpg_lun_lock to struct mutex so core_tpg_add_node_to_devs()
can perform RCU updater logic without releasing ->tpg_lun_mutex.
Also, drop core_tpg_clear_object_luns() and it's single consumer
in iscsi-target, which is duplicating TPG LUN shutdown logic and
is current code results in a NOP.
Finally, sbp-target and xen-scsiback fabric driver conversions are
included, which are required due to the non-standard way they use
->tpg_lun_hlist.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Chris Boot <bootc@bootc.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes __core_scsi3_do_alloc_registration() code to
drop pr_reg->pr_reg_tg_pt_lun pointer usage in favor of a new
pr_reg RPTI + existing pr_reg->pr_aptpl_target_lun used by
APTPL metadata logic.
It also includes changes to REGISTER, REGISTER_AND_MOVE and APTPL
feature bit codepaths to use rcu_dereference_check() with the
expected non-zero se_dev_entry->pr_kref reference held.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts the core_scsi3_pr_seq_non_holder() check for non
reservation holding registrations to use an atomic bitop in ->deve_flags
to determine if a registration is currently active.
It also includes associated a set_bit() in __core_scsi3_add_registration()
and clear_bit() in __core_scsi3_free_registration(), if se_dev_entry still
exists, and has not already been released via se_dev_entry shutdown path
in core_disable_device_list_for_node().
Also, clear_bit in core_disable_device_list_for_node as well to ensure
the read-critical path in core_scsi3_pr_seq_non_holder() picks up the
new state, preceeding the final kfree_rcu() call.
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts se_node_acl->device_list[] table for mappedluns
to modern RCU hlist_head usage in order to support an arbitrary number
of node_acl lun mappings.
It converts transport_lookup_*_lun() fast-path code to use RCU read path
primitives when looking up se_dev_entry. It adds a new hlist_head at
se_node_acl->lun_entry_hlist for this purpose.
For transport_lookup_cmd_lun() code, it works with existing per-cpu
se_lun->lun_ref when associating se_cmd with se_lun + se_device.
Also, go ahead and update core_create_device_list_for_node() +
core_free_device_list_for_node() to use ->lun_entry_hlist.
It also converts se_dev_entry->pr_ref_count access to use modern
struct kref counting, and updates core_disable_device_list_for_node()
to kref_put() and block on se_deve->pr_comp waiting for outstanding PR
special-case PR references to drop, then invoke kfree_rcu() to wait
for the RCU grace period to complete before releasing memory.
So now that se_node_acl->lun_entry_hlist fast path access uses RCU
protected pointers, go ahead and convert remaining non-fast path
RCU updater code using ->lun_entry_lock to struct mutex to allow
callers to block while walking se_node_acl->lun_entry_hlist.
Finally drop the left-over core_clear_initiator_node_from_tpg() that
originally cleared lun_access during se_node_acl shutdown, as post
RCU conversion it now becomes duplicated logic.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simplify target core and target drivers by storing the task tag
a.k.a. command identifier inside struct se_cmd.
For several transports (e.g. SRP) tags are 64 bits wide.
Hence add support for 64-bit tags.
(Fix core_tmr_abort_task conversion spec warnings - nab)
(Fix up usb-gadget to use 16-bit tags - HCH + bart)
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove the unneeded fabric_ptr argument, and change the type argument
to pass in a SPC protocol identifier.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Even if the device backend is initialized with protection info is
enabled, some requests don't have the protection info attached for
WRITE SAME command issued by block device helpers, WRITE command with
WRPROTECT=0 by SG_IO ioctl, etc.
So when TCM loopback fabric module is used, se_cmd->t_prot_sg is NULL
for these requests and performing WRITE_INSERT of PI using software
emulation by sbc_dif_generate() causes kernel crash.
To fix this, introduce SCF_PASSTHROUGH_PROT_SG_TO_MEM_NOALLOC for
se_cmd_flags, which is used to determine that se_cmd->t_prot_sg needs
to be allocated or use pre-allocated protection information by scsi
mid-layer.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: target-devel@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Drivers may override the WCE flag, in which case the DPOFUA flag in
MODE SENSE might differ from the check used to reject invalid FUA
bits in sbc_check_dpofua. Also now that we reject invalid FUA
bits early there is no need to duplicate the same buggy check
down in the fileio code.
As the DPOFUA flag controls th support for FUA bits on read and
write commands as well as DPO key off all the checks off a single
helper, and deprecate the emulate_dpo and emulate_fua_read attributs.
This fixes various failures in the libiscsi testsuite.
Personally I'd prefer to also remove the emulate_fua_write attribute
as there is no good reason to disable it, but I'll leave that for
a separate discussion.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The following incremental patch saves the current sess_prot_type into
se_node_acl, and will always reset sess_prot_type if a previous saved
value exists. So the PI setting for the fabric's session with backend
devices not supporting PI is persistent across session restart.
(Fix se_node_acl dereference for discovery sessions - DanCarpenter)
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The flag SCF_ACK_KREF is only set but never tested. Hence remove
this flag.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug for COMPARE_AND_WRITE handling with
fabrics using SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC.
It adds the missing allocation for cmd->t_bidi_data_sg within
transport_generic_new_cmd() that is used by COMPARE_AND_WRITE
for the initial READ payload, even if the fabric is already
providing a pre-allocated buffer for cmd->t_data_sg.
Also, fix zero-length COMPARE_AND_WRITE handling within the
compare_and_write_callback() and target_complete_ok_work()
to queue the response, skipping the initial READ.
This fixes COMPARE_AND_WRITE emulation with loopback, vhost,
and xen-backend fabric drivers using SG_TO_MEM_NOALLOC.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of calling target_fabric_configfs_init() +
target_fabric_configfs_register() / target_fabric_configfs_deregister()
target_fabric_configfs_free() from every target driver, rewrite the API
so that we have simple register/unregister functions that operate on
a const operations vector.
This patch also fixes a memory leak in several target drivers. Several
target drivers namely called target_fabric_configfs_deregister()
without calling target_fabric_configfs_free().
A large part of this patch is based on earlier changes from
Bart Van Assche <bart.vanassche@sandisk.com>.
(v2: Add a new TF_CIT_SETUP_DRV macro so that the core configfs code
can declare attributes as either core only or for drivers)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a new target_core_fabric_ops callback for allowing fabric
drivers to expose a TPG attribute for signaling when a T10-PI protected
fabric wants to function with an un-protected device without T10-PI.
This specifically is to allow LIO to perform WRITE_STRIP + READ_INSERT
operations when functioning with non T10-PI enabled devices, seperate
from any available hw offloads the fabric supports.
This is done using a new se_sess->sess_prot_type that is set at fabric
session creation time based upon the TPG attribute. It currently cannot
be changed for individual sessions after initial creation.
Also, update existing target_core_sbc.c code to honor sess_prot_type when
setting up cmd->prot_op + cmd->prot_type assignments.
(Add unlikely and !! boolean conversion in sbc_check_prot - Sagi)
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Doug Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Update vhost-scsi to support F_ANY_LAYOUT using mm/iov_iter.c
logic, and signal VERSION_1 support (MST + Viro + nab)
- Fix iscsi/iser-target to remove problematic active_ts_set usage
(Gavin Guo)
- Update iscsi/iser-target to support multi-sequence sendtargets
(Sagi)
- Fix original PR_APTPL_BUF_LEN 8k size limitation (Martin Svec)
- Add missing WRITE_SAME end-of-device sanity check (Bart)
- Check for LBA + sectors wrap-around in sbc_parse_cdb() (nab)
- Other various minor SPC/SBC compliance fixes based upon Ronnie
Sahlberg test suite (nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (32 commits)
target: Set LBPWS10 bit in Logical Block Provisioning EVPD
target: Fail UNMAP when emulate_tpu=0
target: Fail WRITE_SAME w/ UNMAP=1 when emulate_tpws=0
target: Add sanity checks for DPO/FUA bit usage
target: Perform PROTECT sanity checks for WRITE_SAME
target: Fail I/O with PROTECT bit when protection is unsupported
target: Check for LBA + sectors wrap-around in sbc_parse_cdb
target: Add missing WRITE_SAME end-of-device sanity check
iscsi-target: Avoid IN_LOGOUT failure case for iser-target
target: Fix PR_APTPL_BUF_LEN buffer size limitation
iscsi-target: Drop problematic active_ts_list usage
iscsi/iser-target: Support multi-sequence sendtargets text response
iser-target: Remove duplicate function names
vhost/scsi: potential memory corruption
vhost/scsi: Global tcm_vhost -> vhost_scsi rename
vhost/scsi: Drop left-over scsi_tcq.h include
vhost/scsi: Set VIRTIO_F_ANY_LAYOUT + VIRTIO_F_VERSION_1 feature bits
vhost/scsi: Add ANY_LAYOUT support in vhost_scsi_handle_vq
vhost/scsi: Add ANY_LAYOUT iov -> sgl mapping prerequisites
vhost/scsi: Change vhost_scsi_map_to_sgl to accept iov ptr + len
...
This patch addresses the original PR_APTPL_BUF_LEN = 8k limitiation
for write-out of PR APTPL metadata that Martin has recently been
running into.
It changes core_scsi3_update_and_write_aptpl() to use vzalloc'ed
memory instead of kzalloc, and increases the default hardcoded
length to 256k.
It also adds logic in core_scsi3_update_and_write_aptpl() to double
the original length upon core_scsi3_update_aptpl_buf() failure, and
retries until the vzalloc'ed buffer is large enough to accommodate
the outgoing APTPL metadata.
Reported-by: Martin Svec <martin.svec@zoner.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that fabric_max_sectors is no longer used to enforce the maximum
I/O size, go ahead and drop it's left-over usage in target-core and
associated backend drivers.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
For SPI drivers use the message definitions from scsi.h, and for target
drivers introduce a new TCM_*_TAG namespace.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
This patch adds a force_pr_aptpl device attribute used to force SPC-3 PR
Activate Persistence across Target Power Loss (APTPL) operation. This
makes PR metadata write-out occur during state change regardless if new
PERSISTENT_RESERVE_OUT CDBs have their APTPL feature bit set.
This is useful during H/A failover in active/passive setups where all PR
state is being re-created on a different node, driven by configfs backend
device + export layout and pre-loaded $DEV/pr/res_aptpl_metadata.
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The target code has a rather generous helping of smp_mb__after_atomic()
throughout the code base. Most atomic operations were followed by one
and none were preceded by smp_mb__before_atomic(), nor accompanied by a
comment explaining the need for a barrier.
Instead of trying to prove for every case whether or not it is needed,
this patch introduces atomic_inc_mb() and atomic_dec_mb(), which
explicitly include the memory barriers before and after the atomic
operation. For now they are defined in a target header, although they
could be of general use.
Most of the existing atomic/mb combinations were replaced by the new
helpers. In a few cases the atomic was sandwiched in
spin_lock/spin_unlock and I simply removed the barrier.
I suspect that in most cases the correct conversion would have been to
drop the barrier. I also suspect that a few cases exist where a) the
barrier was necessary and b) a second barrier before the atomic would
have been necessary and got added by this patch.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Linus Torvalds
Bart Van Assche
Quinn Tran
Jamie Pocas
Nicholas Bellinger
Christoph Hellwig
Roland Dreier
Chris Zankel
Sagi Grimberg
Hannes Reinecke
Akinobu Mita
Christoph Hellwig
Joern Engel