commit 22a85e4cd5 (spi/imx: add device tree probe support) broke spi-imx usage
when the SPI chipselect is the one internal to the controller.
On a mx31pdk board the following error is seen:
Registering mxc_nand as whole device
------------[ cut here ]------------
WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x4c/0xf4()
autorequest GPIO-0
Modules linked in:
[<c0014410>] (unwind_backtrace+0x0/0xf4) from [<c0025754>] (warn_slowpath_common+0x4c/0x64)
[<c0025754>] (warn_slowpath_common+0x4c/0x64) from [<c0025800>] (warn_slowpath_fmt+0x30/0x40)
[<c0025800>] (warn_slowpath_fmt+0x30/0x40) from [<c0198688>] (gpio_ensure_requested+0x4c/0xf4)
[<c0198688>] (gpio_ensure_requested+0x4c/0xf4) from [<c01988c8>] (gpio_direction_output+0xa0/0x138)
[<c01988c8>] (gpio_direction_output+0xa0/0x138) from [<c01ed198>] (spi_imx_setup+0x38/0x4c)
[<c01ed198>] (spi_imx_setup+0x38/0x4c) from [<c01eb5d0>] (spi_setup+0x38/0x50)
[<c01eb5d0>] (spi_setup+0x38/0x50) from [<c01eb85c>] (spi_add_device+0x94/0x124)
[<c01eb85c>] (spi_add_device+0x94/0x124) from [<c01eb960>] (spi_new_device+0x74/0xac)
[<c01eb960>] (spi_new_device+0x74/0xac) from [<c01eb9b8>] (spi_match_master_to_boardinfo+0x20/0x40)
[<c01eb9b8>] (spi_match_master_to_boardinfo+0x20/0x40) from [<c01eba88>] (spi_register_master+0xb0/0x104)
[<c01eba88>] (spi_register_master+0xb0/0x104) from [<c01ec0b4>] (spi_bitbang_start+0x104/0x17c)
[<c01ec0b4>] (spi_bitbang_start+0x104/0x17c) from [<c02c2c4c>] (spi_imx_probe+0x2fc/0x404)
[<c02c2c4c>] (spi_imx_probe+0x2fc/0x404) from [<c01c2498>] (platform_drv_probe+0x18/0x1c)
[<c01c2498>] (platform_drv_probe+0x18/0x1c) from [<c01c1058>] (driver_probe_device+0x78/0x174)
[<c01c1058>] (driver_probe_device+0x78/0x174) from [<c01c11e0>] (__driver_attach+0x8c/0x90)
[<c01c11e0>] (__driver_attach+0x8c/0x90) from [<c01c0860>] (bus_for_each_dev+0x60/0x8c)
[<c01c0860>] (bus_for_each_dev+0x60/0x8c) from [<c01c0088>] (bus_add_driver+0xa0/0x288)
[<c01c0088>] (bus_add_driver+0xa0/0x288) from [<c01c179c>] (driver_register+0x78/0x18c)
[<c01c179c>] (driver_register+0x78/0x18c) from [<c0008490>] (do_one_initcall+0x34/0x178)
[<c0008490>] (do_one_initcall+0x34/0x178) from [<c03a5204>] (kernel_init+0x74/0x118)
[<c03a5204>] (kernel_init+0x74/0x118) from [<c000f65c>] (kernel_thread_exit+0x0/0x8)
---[ end trace 759f924b30fd5a44 ]---
Fix this issue by using the original chip select logic and make spi-imx to work again.
Tested on a mx31pdk that uses the hardware SPI chipselect pins and also
on a mx27pdk that uses GPIO as SPI chipselect.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It adds device tree probe support for spi-imx driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It copies gpio number passed via platform data embedded pointer into
driver private data, so that we do not need to refer to this embedded
pointer passed by platform data after probe function exits.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Software defined version number is not stable enough to be used
in device type naming scheme. The patch changes it to use implicit
soc name for spi device type definition. In this way, we can easily
align the naming scheme with device tree binding, which comes later.
It removes fifosize from spi_imx_data and adds devtype there, so that
fifosize can be set in an inline function according to devtype.
Also, cpu_is_mx can be replaced by inline functions checking devtype.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The only difference between SPI_IMX_VER_0_7 and SPI_IMX_VER_0_4 is
.config function. The patch uses cpu_is_mx35 (to be removed) as the
temporary solution to consolidate functions spi_imx0_4_config and
spi_imx0_7_config into mx31_config. As a result, type SPI_IMX_VER_0_7
can be merged into SPI_IMX_VER_0_4.
It also renames function spi_imx0_4_reset to mx31_reset to keep
consistency with other function naming.
A couple of redundant macros, MX3_CSPISTAT and MX3_CSPISTAT_RR,
together with the useless type SPI_IMX_VER_0_5 also get cleaned up.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It's confusing to use spi_imx2_3 to name SPI_IMX_VER_2_3 function
and macro, as it easily make people think of imx2 and imx3. It's
better to use specific soc name just like what other SPI_IMX_VER
do. For SPI_IMX_VER_2_3 case, it will be mx51. To distinguish it
from CSPI on mx51, mx51_ecspi might be a good choice.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
SPI_IMX_VER_0_0 covers i.mx21 and i.mx27. It makes more sense to
use mx21 rather than mx27 to name SPI_IMX_VER_0_0 function and
macro, since i.mx21 comes out ealier than i.mx27.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
spi_imx_devtype_data has already been driver private data. There is
really no need to make a copy in spi_imx_data. Instead, a reference
pointer works perfectly fine.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Sort the SPI makefile and enforce the naming convention spi_*.c for
spi drivers.
This change also rolls the contents of atmel_spi.h into the .c file
since there is only one user of that particular include file.
v2: - Use 'spi-' prefix instead of 'spi_' to match what seems to be
be the predominant pattern for subsystem prefixes.
- Clean up filenames in Kconfig and header comment blocks
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Fabio Estevam
Shawn Guo
Grant Likely