Before this commit sensor_hub_input_attr_get_raw_value() failed to take
the signedness of 16 and 8 bit values into account, returning e.g.
65436 instead of -100 for the z-axis reading of an accelerometer.
This commit adds a new is_signed parameter to the function and makes all
callers pass the appropriate value for this.
While at it, this commit also fixes up some neighboring lines where
statements were needlessly split over 2 lines to improve readability.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add GPLv2+ SPDX identifier and update email for author's drivers.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The old code was based on a DHT11 datasheet which specifies a measurement
range of 20%-90% RH. Turns out the sensor actually reports values outside
this range, so we should support it as far as possible.
Reported-by: Edward Attfield <edward@attfield.ca>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove unnecessary unaligned access routine in hts221_read_oneshot() and
the related include
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce regmap API support to access to i2c/spi bus instead of
using a custom support.
Remove lock mutex since concurrency is already managed by regmap API
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove following sparse warnings in hts221_parse_temp_caldata() and in
hts221_parse_rh_caldata():
drivers/iio/humidity/hts221_core.c:302:19: warning: cast to
restricted __le16
drivers/iio/humidity/hts221_core.c:314:18: warning: cast to
restricted __le16
drivers/iio/humidity/hts221_core.c:320:18: warning: cast to
restricted __le16
drivers/iio/humidity/hts221_core.c:355:18: warning: cast to
restricted __le16
drivers/iio/humidity/hts221_core.c:361:18: warning: cast to
restricted __le16
Fixes: e4a70e3e7d ("iio: humidity: add support to hts221 rh/temp combo device")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd atomisp
cleanups (take the media tree's version).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
g3ioPBqmqC/2DSbldr2o
=/ebw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Move data-ready configuration in hts221_buffer.c since it is only related
to trigger logic
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add open drain support in order to share requested IRQ line between
hts221 device and other peripherals
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for active low interrupts (IRQF_TRIGGER_LOW and
IRQF_TRIGGER_FALLING). Configure the device as active high or low
according to the requested irq line.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Configure sensor ODR just in hts221_write_raw() in order to avoid
to set device sample rate multiple times.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
GENMASK(6, 3) in CTRL_REG1 and GENMASK(6, 2) in CTRL_REG2 are marked
reserved. Do not changed the original value (not declared in the
datasheet) during power-down/suspend routines.
Fixes: e4a70e3e7d (iio: humidity: add support to hts221 rh/temp device)
Fixes: b7079eeac5 (iio: humidity: hts221: add power management support)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable Block Data Update in hts221_probe() in order to avoid to reconfigure
it every time the sensor is enabled
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move bit-shift in hts221_write_with_mask() instead of coding
the shift depth in the configured value. That change will be necessary
to fix an issue in device power-down procedure.
Simplify hts221_avg_list table management
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add of_match_table for Measurement-Specialties htu21 temperature & humidity sensor and humidity part of MS8607 sensor
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add of_match_table and point it to a list of compatible device tree
device id's.
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Include datasheet links, add i2c_device_id entries, and update
kconfig help for compatible HDC10xx devices: HDC1000, HDC1008,
HDC1010, HDC1050, and HDC1080.
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add system sleep power management support to hts221 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
attrs filed of iio_info structure. As the attrs field of iio_info
structures is constant, so these attribute_group structures can also be
declared constant.
Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
File size before:
text data bss dec hex filename
3459 488 0 3947 f6b drivers/iio/humidity/hdc100x.o
File size after:
text data bss dec hex filename
3507 424 0 3931 f5b drivers/iio/humidity/hdc100x.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Environmental humidity sensor is a hid defined sensor,
it shows raw humidity measurement of air.
More information can be found in:
http://www.usb.org/developers/hidpage/HUTRR39b.pdf
According to IIO ABI definition, humidityrelative data output unit is
milli percent. Add the unit convert from percent to milli percent.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This resolves the merge errors that were reported in linux-next and it
picks up the staging and IIO fixes that we need/want in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DHT22 (AM2302) datasheet specifies that the LOW start pulse should not
exceed 20ms. However, observations with an oscilloscope of an RPi Model 2B
(rev 1.1) communicating with a DHT22 sensor showed that the driver was
consistently sending start pulses longer than 20ms:
Kernel 4.7.10-v7+ (n=132):
Minimum pulse length: 20.20ms
Maximum: 29.84ms
Mean: 24.96ms
StDev: 2.82ms
Sensor response rate: 100%
Read success rate: 76%
On kernel 4.8, the start pulse was so long that the sensor would not even
respond 97% of the time:
Kernel 4.8.16-v7+ (n=100):
Minimum pulse length: 30.4ms
Maximum: 74.4ms
Mean: 39.3ms
StDev: 10.2ms
Sensor response rate: 3%
Read success rate: 3%
The driver would return ETIMEDOUT and write log messages like this:
[ 51.430987] dht11 dht11@0: Only 1 signal edges detected
[ 66.311019] dht11 dht11@0: Only 0 signal edges detected
Replacing msleep(18) with usleep_range(18000, 20000) made the pulse length
sane again and restored responsiveness:
Kernel 4.8.16-v7+ with usleep_range (n=123):
Minimum pulse length: 18.16ms
Maximum: 20.20ms
Mean: 19.85ms
StDev: 0.51ms
Sensor response rate: 100%
Read success rate: 84%
Cc: stable@vger.kernel.org
Signed-off-by: John Brooks <john@fastquake.com>
Reviewed-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Support driver probe by reading unique HID on systems based on ACPI instead
of DT compatible strings.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds devicetree support for the si7020 iio driver. Since it works
well without requiring any additional property, its compatible string is
added to the trivial i2c devices bindings list.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Triggered buffer support uses the HDC100X's dual acquisition mode
to read both humidity and temperature in one shot.
This patch depends on
447136effbf4 ("iio: humidity: hdc100x: fix sensor data reads of
temp and humidity")
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support to STM HTS221 humidity + temperature sensor
http://www.st.com/resource/en/datasheet/hts221.pdf
- continuous mode support
- i2c support
- spi support
- trigger mode support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
hdc100x supports Texas Instruments HDC1000 and HDC1008 relative
humidity and temperature sensors. Add these product names to
Kconfig.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the i2c_smbus_read_byte commmands used to retrieve the sensor
data with an i2c_master_recv command.
The smbus read byte method fails because the device does not expect a
stop condition after sending the first byte. When we issue the second
read, we are getting the first byte again. Net effect is that of the 14
bits used for the measurement, the 8 most significant bits are correct,
the lower 6 are not.
None of the smbus read protocols follow the pattern this device requires
(S Addr Rd [A] Data [A] Data NA P), hence the switch to an i2c receive
transaction.
Applicable from original introduction of this driver, but will require
backporting due to churn in the code.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Select IIO_BUFFER and IIO_TRIGGERED_BUFFER to compile.
Remove IIO_TRIGGER if present since IIO_BUFFER selects it.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the iio_pollfunc_store_time parameter during triggered buffer
set-up to get valid timestamps.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-By: Tiberiu Breana <tiberiu.a.breana@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We want the fixes in here, and we can resolve a merge issue in
drivers/iio/industrialio-trigger.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shifting sensor data to the right 2 bits was incorrect and caused the
scaling values + offsets to be invalid.
Reported-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Tested-by: Alison Schofield <amsfield22@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IIO_TEMP channel was being incorrectly reported back as Celsius when it
should have been milliCelsius. This is via an incorrect scale value being
returned to userspace.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The I2C drivers have an i2c_device_id array but that information isn't
exported to the modules using the MODULE_DEVICE_TABLE() macro. So the
modules autoloading won't work if the I2C device is registered using
OF or legacy board files due missing alias information in the modules.
The issue was found using Kieran Bingham's coccinelle semantic patch:
https://lkml.org/lkml/2016/5/10/520
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We haven't taken the lock yet so we don't need to unlock here.
Fixes: 0d96d5ead3 ('iio: humidity: Add triggered buffer support for AM2315')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Apply the correct mask to enable all available humidity integration
times. Currently, the driver defaults to 6500 and all is okay with that.
However, if 3850 is selected we get a stuck bit and can't change back
to 6500 or select 2500. (Verified with HDC1008)
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Matt Ranostay <mranostay@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add basic support for the Aosong AM2315 relative humidity
and ambient temperature sensor.
Includes support for raw readings and ACPI detection.
Datasheet:
http://www.aosong.com/asp_bin/Products/en/AM2315.pdf
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* Unify log messages
* Add more DEBUG messages
Apparently this driver is working unreliably on some platforms that I can't
test. Therefore I want an easy way for bug reporters to provide useful
information without making the driver too chatty by default.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Previously most drivers that used a i2c_check_functionality() check
condition required various error codes on failure. This patchset
converts to a standard of -EOPNOTSUPP
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Wall time obtained from ktime_get_real_ns is susceptible to sudden jumps due to
user setting the time or due to NTP. Boot time is constantly increasing time
better suited for comparing two timestamps.
Signed-off-by: Abhilash Jindal <klock.android@gmail.com>
Reviewed-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Hans de Goede
Matt Ranostay
Harald Geyer
Lorenzo Bianconi
Linus Torvalds
Greg Kroah-Hartman
Jonathan Cameron
Lorenzo Bianconi
Manivannan Sadhasivam
Michael Stecklein
simran singhal
Song Hongyan
John Brooks
Shrirang Bagul
Paul Kocialkowski
Wei Yongjun
Alison Schofield
Matt Ranostay
Javier Martinez Canillas
Dan Carpenter
Tiberiu Breana
Abhilash Jindal