Christoph Hellwig suggests we should to make APST work out of the box.
Hence relax the the default max latency to make them able to enter
deepest power state on default.
Here are id-ctrl excerpts from two high latency NVMes:
vid : 0x14a4
ssvid : 0x1b4b
mn : CX2-GB1024-Q11 NVMe LITEON 1024GB
ps 3 : mp:0.1000W non-operational enlat:5000 exlat:5000 rrt:3 rrl:3
rwt:3 rwl:3 idle_power:- active_power:-
ps 4 : mp:0.0100W non-operational enlat:50000 exlat:100000 rrt:4 rrl:4
rwt:4 rwl:4 idle_power:- active_power:-
vid : 0x15b7
ssvid : 0x1b4b
mn : A400 NVMe SanDisk 512GB
ps 3 : mp:0.0500W non-operational enlat:51000 exlat:10000 rrt:0 rrl:0
rwt:0 rwl:0 idle_power:- active_power:-
ps 4 : mp:0.0055W non-operational enlat:1000000 exlat:100000 rrt:0 rrl:0
rwt:0 rwl:0 idle_power:- active_power:-
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When a NVMe is in non-op states, the latency is exlat.
The latency will be enlat + exlat only when the NVMe tries to transit
from operational state right atfer it begins to transit to
non-operational state, which should be a rare case.
Therefore, as Andy Lutomirski suggests, use exlat only when deciding power
states to trainsit to.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The failure case, of a create controller request, called
nvme_uninit_ctrl() but didn't do a put to allow the nvme
controller to be deleted.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Per FC-NVME, when lldd or transport detects an i/o error, the
connection must be terminated, which in turn requires the association
to be termianted. Currently the transport simply creates a nvme
completion status of transport error and returns the io. The FC-NVME
spec makes the mandate as initiator and host, depending on the error,
can get out of sync on outstanding io counts (sqhd/sqtail).
Implement the association teardown on lldd or transport detected
errors.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
When we encounter an transport/controller errors, error recovery
kicks in which performs:
1. stops io/admin queues
2. moves transport queues out of LIVE state
3. fast fail pending io
4. schedule periodic reconnects.
But we also need to fast fail incoming IO taht enters after we
already scheduled. Given that our queue is not LIVE anymore, simply
restart the request queues to fail in .queue_rq
Reported-by: Alex Turin <alex@vastdata.com>
Reported-by: shahar.salzman <shahar.salzman@gmail.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
We need to start admin queues too in nvme_kill_queues()
for avoiding hang in remove path[1].
This patch is very similar with 806f026f9b901eaf(nvme: use
blk_mq_start_hw_queues() in nvme_kill_queues()).
[1] hang stack trace
[<ffffffff813c9716>] blk_execute_rq+0x56/0x80
[<ffffffff815cb6e9>] __nvme_submit_sync_cmd+0x89/0xf0
[<ffffffff815ce7be>] nvme_set_features+0x5e/0x90
[<ffffffff815ce9f6>] nvme_configure_apst+0x166/0x200
[<ffffffff815cef45>] nvme_set_latency_tolerance+0x35/0x50
[<ffffffff8157bd11>] apply_constraint+0xb1/0xc0
[<ffffffff8157cbb4>] dev_pm_qos_constraints_destroy+0xf4/0x1f0
[<ffffffff8157b44a>] dpm_sysfs_remove+0x2a/0x60
[<ffffffff8156d951>] device_del+0x101/0x320
[<ffffffff8156db8a>] device_unregister+0x1a/0x60
[<ffffffff8156dc4c>] device_destroy+0x3c/0x50
[<ffffffff815cd295>] nvme_uninit_ctrl+0x45/0xa0
[<ffffffff815d4858>] nvme_remove+0x78/0x110
[<ffffffff81452b69>] pci_device_remove+0x39/0xb0
[<ffffffff81572935>] device_release_driver_internal+0x155/0x210
[<ffffffff81572a02>] device_release_driver+0x12/0x20
[<ffffffff815d36fb>] nvme_remove_dead_ctrl_work+0x6b/0x70
[<ffffffff810bf3bc>] process_one_work+0x18c/0x3a0
[<ffffffff810bf61e>] worker_thread+0x4e/0x3b0
[<ffffffff810c5ac9>] kthread+0x109/0x140
[<ffffffff8185800c>] ret_from_fork+0x2c/0x40
[<ffffffffffffffff>] 0xffffffffffffffff
Fixes: c5552fde102fc("nvme: Enable autonomous power state transitions")
Reported-by: Rakesh Pandit <rakesh@tuxera.com>
Tested-by: Rakesh Pandit <rakesh@tuxera.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
They have known firmware bugs. A fix is apparently in the works --
once fixed firmware is available, someone from Intel (Hi, Keith!)
can adjust the quirk accordingly.
Cc: stable@vger.kernel.org # v4.11
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently only the PCIe driver supports metadata, so we should not claim
integrity support for the other drivers. This prevents nasty crashes
with targets that advertise metadata support on fabrics.
Also use the opportunity to factor out some code into a separate helper
that isn't even compiled if CONFIG_BLK_DEV_INTEGRITY is disabled.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
So that we can have more flags for transport-specific behavior.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
This is what most of the code already does and gives much more useful
prefixes than the device embedded in the pci_dev.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
fix extra controller reference taken on reconnect by moving
reference to initial controller create
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
correct nvme status set on abort. Patch that changed status to being actual
nvme status crossed in the night with the patch that added abort values.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Per the review by Sagi on:
http://lists.infradead.org/pipermail/linux-nvme/2017-April/009261.html
Looked at existing warn vs info vs err dev_xxx levels for the messages
printed on reconnects and deletes:
- Resets due to error and resets transitioned to deletes are dev_warn
- Other reset/disconnect messages are dev_info
- Removed chatty io queue related messages
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Per the recommendation by Sagi on:
http://lists.infradead.org/pipermail/linux-nvme/2017-April/009261.html
An extra reference was pointed out. There's no issue with the
references, but rather a literal interpretation of what the comment
is saying.
Reword the comment to avoid confusion.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Sync with Sagi's recent addition of ctrl_loss_tmo in the core fabrics
layer.
Remove local connect limits and connect_attempts variable.
Use fabrics new nr_connects variable and use of nvmf_should_reconnect()
Refactor duplicate reconnect failure code.
Addresses review comment by Sagi on controller reset support:
http://lists.infradead.org/pipermail/linux-nvme/2017-April/009261.html
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Remove the local copy of reconnect_delay.
Use the value in the controller options directly.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
NVMe may add request into requeue list simply and not kick off the
requeue if hw queues are stopped. Then blk_mq_abort_requeue_list()
is called in both nvme_kill_queues() and nvme_ns_remove() for
dealing with this issue.
Unfortunately blk_mq_abort_requeue_list() is absolutely a
race maker, for example, one request may be requeued during
the aborting. So this patch just calls blk_mq_kick_requeue_list() in
nvme_kill_queues() to handle this issue like what nvme_start_queues()
does. Now all requests in requeue list when queues are stopped will be
handled by blk_mq_kick_requeue_list() when queues are restarted, either
in nvme_start_queues() or in nvme_kill_queues().
Cc: stable@vger.kernel.org
Reported-by: Zhang Yi <yizhan@redhat.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Inside nvme_kill_queues(), we have to start hw queues for
draining requests in sw queues, .dispatch list and requeue list,
so use blk_mq_start_hw_queues() instead of blk_mq_start_stopped_hw_queues()
which only run queues if queues are stopped, but the queues may have
been started already, for example nvme_start_queues() is called in reset work
function.
blk_mq_start_hw_queues() run hw queues in current context, instead
of running asynchronously like before. Given nvme_kill_queues() is
run from either remove context or reset worker context, both are fine
to run hw queue directly. And the mutex of namespaces_mutex isn't a
problem too becasue nvme_start_freeze() runs hw queue in this way
already.
Cc: stable@vger.kernel.org
Reported-by: Zhang Yi <yizhan@redhat.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In the case of small NVMe-oF queue size (<32) we may enter a deadlock
caused by the fact that the IB completions aren't sent waiting for 32
and the send queue will fill up.
The error is seen as (using mlx5):
[ 2048.693355] mlx5_0:mlx5_ib_post_send:3765:(pid 7273):
[ 2048.693360] nvme nvme1: nvme_rdma_post_send failed with error code -12
This patch changes the way the signaling is done so that it depends on
the queue depth now. The magic define has been removed completely.
Cc: stable@vger.kernel.org
Signed-off-by: Marta Rybczynska <marta.rybczynska@kalray.eu>
Signed-off-by: Samuel Jones <sjones@kalray.eu>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Pull block fixes from Jens Axboe:
"A small collection of fixes that should go into this cycle.
- a pull request from Christoph for NVMe, which ended up being
manually applied to avoid pulling in newer bits in master. Mostly
fibre channel fixes from James, but also a few fixes from Jon and
Vijay
- a pull request from Konrad, with just a single fix for xen-blkback
from Gustavo.
- a fuseblk bdi fix from Jan, fixing a regression in this series with
the dynamic backing devices.
- a blktrace fix from Shaohua, replacing sscanf() with kstrtoull().
- a request leak fix for drbd from Lars, fixing a regression in the
last series with the kref changes. This will go to stable as well"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvmet: release the sq ref on rdma read errors
nvmet-fc: remove target cpu scheduling flag
nvme-fc: stop queues on error detection
nvme-fc: require target or discovery role for fc-nvme targets
nvme-fc: correct port role bits
nvme: unmap CMB and remove sysfs file in reset path
blktrace: fix integer parse
fuseblk: Fix warning in super_setup_bdi_name()
block: xen-blkback: add null check to avoid null pointer dereference
drbd: fix request leak introduced by locking/atomic, kref: Kill kref_sub()
On rdma read errors, release the sq ref that was taken
when the req was initialized. This avoids a hang in
nvmet_sq_destroy() when the queue is being freed.
Signed-off-by: Vijay Immanuel <vijayi@attalasystems.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Per the recommendation by Sagi on:
http://lists.infradead.org/pipermail/linux-nvme/2017-April/009261.html
Rather than waiting for reset work thread to stop queues and abort the ios,
immediately stop the queues on error detection. Reset thread will restop
the queues (as it's called on other paths), but it does not appear to have
a side effect.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
In order to create an association, the remoteport must be
serving either a target role or a discovery role.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
CMB doesn't get unmapped until removal while getting remapped on every
reset. Add the unmapping and sysfs file removal to the reset path in
nvme_pci_disable to match the mapping path in nvme_pci_enable.
Fixes: 202021c1a ("nvme : Add sysfs entry for NVMe CMBs when appropriate")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Reviewed-By: Stephen Bates <sbates@raithlin.com>
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block fixes from Jens Axboe:
"A smaller collection of fixes that should go into -rc1. This contains:
- A fix from Christoph, fixing a regression with the WRITE_SAME and
partial completions. Caused a BUG() on ppc.
- Fixup for __blk_mq_stop_hw_queues(), it should be static. From
Colin.
- Removal of dmesg error messages on elevator switching, when invoked
from sysfs. From me.
- Fix for blk-stat, using this_cpu_ptr() in a section only protected
by rcu_read_lock(). This breaks when PREEMPT_RCU is enabled. From
me.
- Two fixes for BFQ from Paolo, one fixing a crash and one updating
the documentation.
- An error handling lightnvm memory leak, from Rakesh.
- The previous blk-mq hot unplug lock reversal depends on the CPU
hotplug rework that isn't in mainline yet. This caused a lockdep
splat when people unplugged CPUs with blk-mq devices. From Wanpeng.
- A regression fix for DIF/DIX on blk-mq. From Wen"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: handle partial completions for special payload requests
blk-mq: NVMe 512B/4K+T10 DIF/DIX format returns I/O error on dd with split op
blk-stat: don't use this_cpu_ptr() in a preemptable section
elevator: remove redundant warnings on IO scheduler switch
block, bfq: stress that low_latency must be off to get max throughput
block, bfq: use pointer entity->sched_data only if set
nvme: lightnvm: fix memory leak
blk-mq: make __blk_mq_stop_hw_queues static
lightnvm: remove unused rq parameter of nvme_nvm_rqtocmd() to kill warning
block/mq: fix potential deadlock during cpu hotplug
Free up kmalloc allocated memory if failure happens while handling L2P
table transfer in nvme_nvm_get_l2p_tbl.
Fixes: 8e79b5cb ("lightnvm: move block provisioning to targets")
Signed-off-by: Rakesh Pandit <rakesh@tuxera.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=eE4D
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add framework for supporting PCIe devices in Endpoint mode (Kishon
Vijay Abraham I)
- use non-postable PCI config space mappings when possible (Lorenzo
Pieralisi)
- clean up and unify mmap of PCI BARs (David Woodhouse)
- export and unify Function Level Reset support (Christoph Hellwig)
- avoid FLR for Intel 82579 NICs (Sasha Neftin)
- add pci_request_irq() and pci_free_irq() helpers (Christoph Hellwig)
- short-circuit config access failures for disconnected devices (Keith
Busch)
- remove D3 sleep delay when possible (Adrian Hunter)
- freeze PME scan before suspending devices (Lukas Wunner)
- stop disabling MSI/MSI-X in pci_device_shutdown() (Prarit Bhargava)
- disable boot interrupt quirk for ASUS M2N-LR (Stefan Assmann)
- add arch-specific alignment control to improve device passthrough by
avoiding multiple BARs in a page (Yongji Xie)
- add sysfs sriov_drivers_autoprobe to control VF driver binding
(Bodong Wang)
- allow slots below PCI-to-PCIe "reverse bridges" (Bjorn Helgaas)
- fix crashes when unbinding host controllers that don't support
removal (Brian Norris)
- add driver for MicroSemi Switchtec management interface (Logan
Gunthorpe)
- add driver for Faraday Technology FTPCI100 host bridge (Linus
Walleij)
- add i.MX7D support (Andrey Smirnov)
- use generic MSI support for Aardvark (Thomas Petazzoni)
- make Rockchip driver modular (Brian Norris)
- advertise 128-byte Read Completion Boundary support for Rockchip
(Shawn Lin)
- advertise PCI_EXP_LNKSTA_SLC for Rockchip root port (Shawn Lin)
- convert atomic_t to refcount_t in HV driver (Elena Reshetova)
- add CPU IRQ affinity in HV driver (K. Y. Srinivasan)
- fix PCI bus removal in HV driver (Long Li)
- add support for ThunderX2 DMA alias topology (Jayachandran C)
- add ThunderX pass2.x 2nd node MCFG quirk (Tomasz Nowicki)
- add ITE 8893 bridge DMA alias quirk (Jarod Wilson)
- restrict Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
(Manish Jaggi)
* tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (146 commits)
PCI: Don't allow unbinding host controllers that aren't prepared
ARM: DRA7: clockdomain: Change the CLKTRCTRL of CM_PCIE_CLKSTCTRL to SW_WKUP
MAINTAINERS: Add PCI Endpoint maintainer
Documentation: PCI: Add userguide for PCI endpoint test function
tools: PCI: Add sample test script to invoke pcitest
tools: PCI: Add a userspace tool to test PCI endpoint
Documentation: misc-devices: Add Documentation for pci-endpoint-test driver
misc: Add host side PCI driver for PCI test function device
PCI: Add device IDs for DRA74x and DRA72x
dt-bindings: PCI: dra7xx: Add DT bindings to enable unaligned access
PCI: dwc: dra7xx: Workaround for errata id i870
dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode
PCI: dwc: dra7xx: Add EP mode support
PCI: dwc: dra7xx: Facilitate wrapper and MSI interrupts to be enabled independently
dt-bindings: PCI: Add DT bindings for PCI designware EP mode
PCI: dwc: designware: Add EP mode support
Documentation: PCI: Add binding documentation for pci-test endpoint function
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: imx6: Fix spelling mistake: "contol" -> "control"
...
With gcc 4.1.2:
drivers/nvme/host/lightnvm.c: In function ‘nvme_nvm_submit_io’:
drivers/nvme/host/lightnvm.c:498: warning: ‘rq’ is used uninitialized in this function
Indeed, since commit 2e13f33a24 ("lightnvm: create cmd before
allocating request"), the request is passed to nvme_nvm_rqtocmd() before
it is allocated.
Fortunately, as of commit 91276162de ("lightnvm: refactor end_io
functions for sync"), nvme_nvm_rqtocmd () no longer uses the passed
request, so this warning is a false positive.
Drop the unused parameter to clean up the code and kill the warning.
Fixes: 2e13f33a24 ("lightnvm: create cmd before allocating request")
Fixes: 91276162de ("lightnvm: refactor end_io functions for sync")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Create nvme command before allocating a request using
nvme_alloc_request, which uses the command direction. Up until now, the
command has been zeroized, so all commands have been allocated as a
read operation.
Signed-off-by: Javier González <javier@cnexlabs.com>
Reviewed-by: Matias Bjørling <matias@cnexlabs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Remove the request_idx parameter, which can't be used safely now that we
support I/O schedulers with blk-mq. Except for a superflous check in
mtip32xx it was unused anyway.
Also pass the tag_set instead of just the driver data - this allows drivers
to avoid some code duplication in a follow on cleanup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Christoph writes:
"A couple more updates for 4.12. The biggest pile is fc and lpfc
updates from James, but there are various small fixes and cleanups as
well."
Fixes up a few merge issues, and also a warning in
lpfc_nvmet_rcv_unsol_abort() if CONFIG_NVME_TARGET_FC isn't enabled.
Signed-off-by: Jens Axboe <axboe@fb.com>
This function just returns the same error code and sense data as
the default statement in the switch in the caller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
The current command submission code uses a sector-based value when
considering the maximum number of blocks per command. With a
4k-formatted namespace and a command exceeding max hardware limits, this
calculation doesn't split IOs which should be split and fails in the
nvme layer. This patch fixes that calculation and enables IO splitting
in these circumstances.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Do not call nvmf_free_options() from the nvme_fc_ctlr destructor if
nvme_fc_create_ctrl() returns an error, because nvmf_create_ctrl()
frees the options when an error is returned.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We're probably going to be stuck quirking APST off on an over-broad
range of devices for 4.11. Let's make it easy to override the quirk
for testing.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Debugging APST is currently a bit of a pain. This gives optional
simple log messages that describe the APST state.
The easiest way to use this is probably with the nvme_core.dyndbg=+p
module parameter.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
There was a typo in the description of the timeout heuristic.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Found by sparse.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Found by sparse.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
That's what it's used as.
Found by sparse.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
The passed in desc_len is a big endian value, so mark it as such.
Found by sparse.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Found by sparse.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Found by sparse.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
This patch actually does quite a few things. When looking to add
controller reset support, the organization modeled after rdma was
very fragmented. rdma duplicates the reset and teardown paths and does
different things to the block layer on the two paths. The code to build
up the controller is also duplicated between the initial creation and
the reset/error recovery paths. So I decided to make this sane.
I reorganized the controller creation and teardown so that there is a
connect path and a disconnect path. Initial creation obviously uses
the connect path. Controller teardown will use the disconnect path,
followed last access code. Controller reset will use the disconnect
path to stop operation, and then the connect path to re-establish
the controller.
Along the way, several things were fixed
- aens were not properly set up. They are allocated differently from
the per-request structure on the blk queues.
- aens were oddly torn down. the prior patch corrected to abort, but
we still need to dma unmap and free relative elements.
- missed a few ref counting points: in aen completion and on i/o's
that fail
- controller initial create failure paths were still confused vs teardown
before converting to ref counting vs after we convert to refcounting.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add abort support for aens. Commonized the op abort to apply to aen or
real ios (caused some reorg/routine movement). Abort path sets termination
flag in prep for next patch that will be watching i/o abort completion
before proceeding with controller teardown.
Now that we're aborting aens, the "exit" code that simply cleared out
their context no longer applies.
Also clarified how we detect an AEN vs a normal io - by a flag, not
by whether a rq exists or the a rqno is out of range.
Note: saw some interesting cases where if the queues are stopped and
we're waiting for the aborts, the core layer can call the complete_rq
callback for the io. So the io completion synchronizes link side completion
with possible blk layer completion under error.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The code validates the command_id in the response to the original
sqe command. But prior code was using the rq->rqno as the sqe command
id. The core layer overwrites what the transport set there originally.
Use the actual sqe content.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Kai-Heng Feng
James Smart
Sagi Grimberg
Rakesh Pandit
Ming Lei
Andy Lutomirski
Christoph Hellwig
Marta Rybczynska
Linus Torvalds
Vijay Immanuel
Jon Derrick
Geert Uytterhoeven
Javier González
Jens Axboe
Ewan D. Milne