Add trace event to monitor the performance value changes which is
controlled by cpu governors.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
AMD P-State is the AMD CPU performance scaling driver that introduces a
new CPU frequency control mechanism on AMD Zen based CPU series in Linux
kernel. The new mechanism is based on Collaborative processor
performance control (CPPC) which is finer grain frequency management
than legacy ACPI hardware P-States. Current AMD CPU platforms are using
the ACPI P-states driver to manage CPU frequency and clocks with
switching only in 3 P-states. AMD P-State is to replace the ACPI
P-states controls, allows a flexible, low-latency interface for the
Linux kernel to directly communicate the performance hints to hardware.
AMD P-State leverages the Linux kernel governors such as *schedutil*,
*ondemand*, etc. to manage the performance hints which are provided by CPPC
hardware functionality. The first version for AMD P-State is to support one
of the Zen3 processors, and we will support more in future after we verify
the hardware and SBIOS functionalities.
There are two types of hardware implementations for AMD P-State: one is full
MSR support and another is shared memory support. It can use
X86_FEATURE_CPPC feature flag to distinguish the different types.
Using the new AMD P-State method + kernel governors (*schedutil*,
*ondemand*, ...) to manage the frequency update is the most appropriate
bridge between AMD Zen based hardware processor and Linux kernel, the
processor is able to adjust to the most efficiency frequency according to
the kernel scheduler loading.
Please check the detailed CPU feature and MSR register description in
Processor Programming Reference (PPR) for AMD Family 19h Model 51h,
Revision A1 Processors:
https://www.amd.com/system/files/TechDocs/56569-A1-PUB.zip
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce cpufreq HW driver which can support
CPU frequency adjust in MT6779 platform.
Signed-off-by: Hector.Yuan <hector.yuan@mediatek.com>
[ Viresh: Massaged the patch and cleaned some stuff. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Drop support for depercated platforms using SFI, drop the entire
support for SFI that has been long deprecated too and make some
janitorial changes on top of that (Andy Shevchenko).
-----BEGIN PGP SIGNATURE-----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=jlPz
-----END PGP SIGNATURE-----
Merge tag 'sfi-removal-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull Simple Firmware Interface (SFI) support removal from Rafael Wysocki:
"Drop support for depercated platforms using SFI, drop the entire
support for SFI that has been long deprecated too and make some
janitorial changes on top of that (Andy Shevchenko)"
* tag 'sfi-removal-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
x86/platform/intel-mid: Update Copyright year and drop file names
x86/platform/intel-mid: Remove unused header inclusion in intel-mid.h
x86/platform/intel-mid: Drop unused __intel_mid_cpu_chip and Co.
x86/platform/intel-mid: Get rid of intel_scu_ipc_legacy.h
x86/PCI: Describe @reg for type1_access_ok()
x86/PCI: Get rid of custom x86 model comparison
sfi: Remove framework for deprecated firmware
cpufreq: sfi-cpufreq: Remove driver for deprecated firmware
media: atomisp: Remove unused header
mfd: intel_msic: Remove driver for deprecated platform
x86/apb_timer: Remove driver for deprecated platform
x86/platform/intel-mid: Remove unused leftovers (vRTC)
x86/platform/intel-mid: Remove unused leftovers (msic)
x86/platform/intel-mid: Remove unused leftovers (msic_thermal)
x86/platform/intel-mid: Remove unused leftovers (msic_power_btn)
x86/platform/intel-mid: Remove unused leftovers (msic_gpio)
x86/platform/intel-mid: Remove unused leftovers (msic_battery)
x86/platform/intel-mid: Remove unused leftovers (msic_ocd)
x86/platform/intel-mid: Remove unused leftovers (msic_audio)
platform/x86: intel_scu_wdt: Drop mistakenly added const
SFI-based platforms are gone. So does this driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The tango platform is getting removed, so the driver is no
longer needed.
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[ Viresh: Update cpufreq-dt-platdev.c as well ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Pull ARM cpufreq driver changes for v5.9-rc1 from Viresh Kumar:
"Here are the details:
- Adaptive voltage scaling (AVS) support and minor cleanups for
brcmstb driver (Florian Fainelli and Markus Mayer).
- A new tegra driver and cleanup for the existing one (Sumit Gupta and
Jon Hunter).
- Bandwidth level support for Qcom driver along with OPP changes (Sibi
Sankar).
- Cleanups to sti, cpufreq-dt, ap806, CPPC drivers (Viresh Kumar, Lee
Jones, Ivan Kokshaysky, Sven Auhagen, and Xin Hao).
- Make schedutil default governor for ARM (Valentin Schneider).
- Fix dependency issues for imx (Walter Lozano).
- Cleanup around cached_resolved_idx in cpufreq core (Viresh Kumar)."
* 'cpufreq/arm/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: make schedutil the default for arm and arm64
cpufreq: cached_resolved_idx can not be negative
cpufreq: Add Tegra194 cpufreq driver
dt-bindings: arm: Add NVIDIA Tegra194 CPU Complex binding
cpufreq: imx: Select NVMEM_IMX_OCOTP
cpufreq: sti-cpufreq: Fix some formatting and misspelling issues
cpufreq: tegra186: Simplify probe return path
cpufreq: CPPC: Reuse caps variable in few routines
cpufreq: ap806: fix cpufreq driver needs ap cpu clk
cpufreq: cppc: Reorder code and remove apply_hisi_workaround variable
cpufreq: dt: fix oops on armada37xx
cpufreq: brcmstb-avs-cpufreq: send S2_ENTER / S2_EXIT commands to AVS
cpufreq: brcmstb-avs-cpufreq: Support polling AVS firmware
cpufreq: brcmstb-avs-cpufreq: more flexible interface for __issue_avs_command()
cpufreq: qcom: Disable fast switch when scaling DDR/L3
cpufreq: qcom: Update the bandwidth levels on frequency change
OPP: Add and export helper to set bandwidth
cpufreq: blacklist SC7180 in cpufreq-dt-platdev
cpufreq: blacklist SDM845 in cpufreq-dt-platdev
Add support for CPU frequency scaling on Tegra194. The frequency
of each core can be adjusted by writing a clock divisor value to
a MSR on the core. The range of valid divisors is queried from
the BPMP.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The unicore32 port is removed from the kernel.
There is no point to keep stale cpufreq driver for this architecture.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
arm_big_little cpufreq driver was designed as a generic big little
driver that could be used by any platform and make use of bL switcher.
Over years alternate solutions have been designed and merged to deal
with bL/HMP systems like EAS.
Also since no other driver made use of generic arm_big_little cpufreq
driver except Vexpress SPC, we can merge them together as vexpress-spc
driver used only on Vexpress TC2(CA15_CA7) platform.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The kryo cpufreq driver reads the nvmem cell and uses that data to
populate the opps. There are other qcom cpufreq socs like krait which
does similar thing. Except for the interpretation of the read data,
rest of the driver is same for both the cases. So pull the common things
out for reuse.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
[niklas.cassel@linaro.org: split dt-binding into a separate patch and
do not rename the compatible string. Update MAINTAINERS file.]
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Ilia Lin <ilia.lin@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
For some SoCs, the CPU frequency subset and voltage value of each OPP
varies based on the silicon variant in use. The sun50i-cpufreq-nvmem
driver reads the efuse value from the SoC to provide the OPP framework
with required information.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Raspberry Pi's firmware offers and interface though which update it's
performance requirements. It allows us to request for specific runtime
frequencies, which the firmware might or might not respect, depending on
the firmware configuration and thermals.
As the maximum and minimum frequencies are configurable in the firmware
there is no way to know in advance their values. So the Raspberry Pi
cpufreq driver queries them, builds an opp frequency table to then
launch cpufreq-dt.
Also, as the firmware interface might be configured as a module, making
the cpu clock unavailable during init, this implements a full fledged
driver, as opposed to most drivers registering cpufreq-dt, which only
make use of an init routine.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Right now in upstream imx8m cpufreq support just lists a common subset
of OPPs because the higher ones should only be attempted after checking
speed grading in fuses.
Add a small driver which checks speed grading from nvmem cells before
registering cpufreq-dt.
This driver allows unlocking all frequencies for imx8mm and imx8mq and
could be applied to other chips like imx7d
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Add cpufreq driver for Marvell AP-806 found on Aramda 8K.
The AP-806 has DFS (Dynamic Frequency Scaling) with coupled
clock domain for two clusters, so this driver will directly
use generic cpufreq-dt driver as backend.
Based on the work of Omri Itach <omrii@marvell.com>.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The CPUfreq HW present in some QCOM chipsets offloads the steps necessary
for changing the frequency of CPUs. The driver implements the cpufreq
driver interface for this hardware engine.
Signed-off-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the ARM platforms used cpufreq-dt driver irrespective of
whether it's big-little(HMP) or SMP system. This arm_big_little_dt is
not used actively at all.
So let's remove the driver, so that it need not be maintained.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors,
the CPU frequency subset and voltage value of each OPP varies
based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables
defines the voltage and frequency value based on the msm-id in SMEM
and speedbin blown in the efuse combination.
The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
to provide the OPP framework with required information.
This is used to determine the voltage and frequency value for each OPP of
operating-points-v2 table when it is parsed by the OPP framework.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The main addition this time around is the new ARM "SCMI" framework,
which is the latest in a series of standards coming from ARM to do power
management in a platform independent way. This has been through many
review cycles, and it relies on a rather interesting way of using the
mailbox subsystem, but in the end I agreed that Sudeep's version was
the best we could do after all.
Other changes include:
- the ARM CCN driver is moved out of drivers/bus into drivers/perf,
which makes more sense. Similarly, the performance monitoring
portion of the CCI driver are moved the same way and cleaned up
a little more.
- a series of updates to the SCPI framework
- support for the Mediatek mt7623a SoC in drivers/soc
- support for additional NVIDIA Tegra hardware in drivers/soc
- a new reset driver for Socionext Uniphier
- lesser bug fixes in drivers/soc, drivers/tee, drivers/memory, and
drivers/firmware and drivers/reset across platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Pmsx
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The main addition this time around is the new ARM "SCMI" framework,
which is the latest in a series of standards coming from ARM to do
power management in a platform independent way.
This has been through many review cycles, and it relies on a rather
interesting way of using the mailbox subsystem, but in the end I
agreed that Sudeep's version was the best we could do after all.
Other changes include:
- the ARM CCN driver is moved out of drivers/bus into drivers/perf,
which makes more sense. Similarly, the performance monitoring
portion of the CCI driver are moved the same way and cleaned up a
little more.
- a series of updates to the SCPI framework
- support for the Mediatek mt7623a SoC in drivers/soc
- support for additional NVIDIA Tegra hardware in drivers/soc
- a new reset driver for Socionext Uniphier
- lesser bug fixes in drivers/soc, drivers/tee, drivers/memory, and
drivers/firmware and drivers/reset across platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (87 commits)
reset: uniphier: add ethernet reset control support for PXs3
reset: stm32mp1: Enable stm32mp1 reset driver
dt-bindings: reset: add STM32MP1 resets
reset: uniphier: add Pro4/Pro5/PXs2 audio systems reset control
reset: imx7: add 'depends on HAS_IOMEM' to fix unmet dependency
reset: modify the way reset lookup works for board files
reset: add support for non-DT systems
clk: scmi: use devm_of_clk_add_hw_provider() API and drop scmi_clocks_remove
firmware: arm_scmi: prevent accessing rate_discrete uninitialized
hwmon: (scmi) return -EINVAL when sensor information is unavailable
amlogic: meson-gx-socinfo: Update soc ids
soc/tegra: pmc: Use the new reset APIs to manage reset controllers
soc: mediatek: update power domain data of MT2712
dt-bindings: soc: update MT2712 power dt-bindings
cpufreq: scmi: add thermal dependency
soc: mediatek: fix the mistaken pointer accessed when subdomains are added
soc: mediatek: add SCPSYS power domain driver for MediaTek MT7623A SoC
soc: mediatek: avoid hardcoded value with bus_prot_mask
dt-bindings: soc: add header files required for MT7623A SCPSYS dt-binding
dt-bindings: soc: add SCPSYS binding for MT7623 and MT7623A SoC
...
The cris architecture is getting removed, including the artpec3
and etraxfs SoCs, so these cpufreq drivers are now unused.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The blackfin architecture is getting removed, so this driver is
now obsolete.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control including CPU DVFS. SCMI Message Protocol is used to
communicate with the SCP.
This patch adds a cpufreq driver for such systems using SCMI interface
to drive CPU DVFS.
Cc: linux-pm@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Since AVR32 arch was removed, at32ap-cpufreq is useless.
Remove this driver.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds DVFS support for the Armada 37xx SoCs
There are up to four CPU frequency loads for Armada 37xx controlled by
the hardware.
This driver associates the CPU load level to a frequency, then the
hardware will switch while selecting a load level.
The hardware also can associate a voltage for each level (AVS support)
but it is not yet supported
Tested-by: Andre Heider <a.heider@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have moved the Ux500 over to use the generic DT based
cpufreq driver, so delete the old custom driver.
At the same time select CPUFREQ_DT from the machine's
Kconfig in order to satisfy the "default ARCH_U8500"
selection on the old driver.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On tango platforms, firmware configures the CPU clock, and Linux is
then only allowed to use the cpu_clk_divider to change the frequency.
Build the OPP table dynamically at init, in order to support whatever
firmware throws at us.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
MT2701/MT7623 is a 32-bit ARMv7 based quad-core (4 * Cortex-A7) with
single cluster and this hardware is also compatible with the existing
driver through enabling CPU frequency feature with operating-points-v2
bindings. Also, this driver actually supports all MediaTek SoCs, the
Kconfig menu entry and file name itself should be updated with more
generic name to drop "MT8173"
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Moving the cooling code into the cpufreq driver caused a possible build failure
when the cpu_thermal helper code is a loadable module or disabled:
drivers/cpufreq/dbx500-cpufreq.o: In function `dbx500_cpufreq_ready':
dbx500-cpufreq.c:(.text.dbx500_cpufreq_ready+0x4): undefined reference to `cpufreq_cooling_register'
This adds the same dependency that we have in other cpufreq drivers,
forcing the driver to be disabled when we can't possibly link it.
Fixes: 19678ffb9f (cpufreq: dbx500: Manage cooling device from cpufreq driver)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a new cpufreq driver for Tegra186 (and likely later).
The CPUs are organized into two clusters, Denver and A57,
with two and four cores respectively. CPU frequency can be
adjusted by writing the desired rate divisor and a voltage
hint to a special per-core register.
The frequency of each core can be set individually; however,
this is just a hint as all CPUs in a cluster will run at
the maximum rate of non-idle CPUs in the cluster.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some TI SoCs, like those in the AM335x, AM437x, DRA7x, and AM57x families,
have different OPPs available for the MPU depending on which specific
variant of the SoC is in use. This can be determined through use of the
revision and an eFuse register present in the silicon. Introduce a
ti-cpufreq driver that can read the aformentioned values and provide
them as version matching data to the opp framework. Through this the
opp-supported-hw dt binding that is part of the operating-points-v2
table can be used to indicate availability of OPPs for each device.
This driver also creates the "cpufreq-dt" platform_device after passing
the version matching data to the OPP framework so that the cpufreq-dt
handles the actual cpufreq implementation. Even without the necessary
data to pass the version matching data the driver will still create this
device to maintain backwards compatibility with operating-points v1
tables.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add the MIPS CPUfreq driver. This driver currently supports CPUfreq on
BMIPS5xxx-based SoCs.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This driver supports voltage and frequency scaling on Broadcom STB SoCs
using AVS firmware with DFS and DVFS support.
Actual frequency or voltage scaling is done exclusively by the AVS
firmware. The driver merely provides a standard CPUfreq interface to
other kernel components and userland, and instructs the AVS firmware to
perform frequency or voltage changes on its behalf.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After switching the core module clocks controlling the Integrator
clock frequencies to the common clock framework, defining the
operating points in the device tree, and activating the generic
DT-based CPUfreq driver, we can retire the old Integrator
cpufreq driver.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.7. Here's the summary of
the changes:
- ATH79: Support for DTB passuing using the UHI boot protocol
- ATH79: Remove support for builtin DTB.
- ATH79: Add zboot debug serial support.
- ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
and DPT-Module.
- ATH79: Update devicetree clock support for AR9132 and AR9331.
- ATH79: Cleanup the DT code.
- ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
- ATH79: Fix regression in PCI window initialization.
- BCM47xx: Move SPROM driver to drivers/firmware/
- BCM63xx: Enable partition parser in defconfig.
- BMIPS: BMIPS5000 has I cache filing from D cache
- BMIPS: BMIPS: Add cpu-feature-overrides.h
- BMIPS: Add Whirlwind support
- BMIPS: Adjust mips-hpt-frequency for BCM7435
- BMIPS: Remove maxcpus from BCM97435SVMB DTS
- BMIPS: Add missing 7038 L1 register cells to BCM7435
- BMIPS: Various tweaks to initialization code.
- BMIPS: Enable partition parser in defconfig.
- BMIPS: Cache tweaks.
- BMIPS: Add UART, I2C and SATA devices to DT.
- BMIPS: Add BCM6358 and BCM63268support
- BMIPS: Add device tree example for BCM6358.
- BMIPS: Improve Improve BCM6328 and BCM6368 device trees
- Lantiq: Add support for device tree file from boot loader
- Lantiq: Allow build with no built-in DT.
- Loongson 3: Reserve 32MB for RS780E integrated GPU.
- Loongson 3: Fix build error after ld-version.sh modification
- Loongson 3: Move chipset ACPI code from drivers to arch.
- Loongson 3: Speedup irq processing.
- Loongson 3: Add basic Loongson 3A support.
- Loongson 3: Set cache flush handlers to nop.
- Loongson 3: Invalidate special TLBs when needed.
- Loongson 3: Fast TLB refill handler.
- MT7620: Fallback strategy for invalid syscfg0.
- Netlogic: Fix CP0_EBASE redefinition warnings
- Octeon: Initialization fixes
- Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
- Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
- Octeon: Correctly handle endian-swapped initramfs images.
- Octeon: Support CN73xx, CN75xx and CN78xx.
- Octeon: Remove dead code from cvmx-sysinfo.
- Octeon: Extend number of supported CPUs past 32.
- Octeon: Remove some code limiting NR_IRQS to 255.
- Octeon: Simplify octeon_irq_ciu_gpio_set_type.
- Octeon: Mark some functions __init in smp.c
- Octeon: Octeon: Add Octeon III CN7xxx interface detection
- PIC32: Add serial driver and bindings for it.
- PIC32: Add PIC32 deadman timer driver and bindings.
- PIC32: Add PIC32 clock timer driver and bindings.
- Pistachio: Determine SoC revision during boot
- Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
- Sibyte: Strip redundant comments from bcm1480_regs.h.
- Panic immediately if panic_on_oops is set.
- module: fix incorrect IS_ERR_VALUE macro usage.
- module: Make consistent use of pr_*
- Remove no longer needed work_on_cpu() call.
- Remove CONFIG_IPV6_PRIVACY from defconfigs.
- Fix registers of non-crashing CPUs in dumps.
- Handle MIPSisms in new vmcore_elf32_check_arch.
- Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
- Allow RIXI to be used on non-R2 or R6 cores.
- Reserve nosave data for hibernation
- Fix siginfo.h to use strict POSIX types.
- Don't unwind user mode with EVA.
- Fix watchpoint restoration
- Ptrace watchpoints for R6.
- Sync icache when it fills from dcache
- I6400 I-cache fills from dcache.
- Various MSA fixes.
- Cleanup MIPS_CPU_* definitions.
- Signal: Move generic copy_siginfo to signal.h
- Signal: Fix uapi include in exported asm/siginfo.h
- Timer fixes for sake of KVM.
- XPA TLB refill fixes.
- Treat perf counter feature
- Update John Crispin's email address
- Add PIC32 watchdog and bindings.
- Handle R10000 LL/SC bug in set_pte()
- cpufreq: Various fixes for Longson1.
- R6: Fix R2 emulation.
- mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
- ELF: ABI and FP fixes.
- Allow for relocatable kernel and use that to support KASLR.
- Fix CPC_BASE_ADDR mask
- Plenty fo smp-cps, CM, R6 and M6250 fixes.
- Make reset_control_ops const.
- Fix kernel command line handling of leading whitespace.
- Cleanups to cache handling.
- Add brcm, bcm6345-l1-intc device tree bindings.
- Use generic clkdev.h header
- Remove CLK_IS_ROOT usage.
- Misc small cleanups.
- CM: Fix compilation error when !MIPS_CM
- oprofile: Fix a preemption issue
- Detect DSP ASE v3 support:1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
MIPS: pic32mzda: fix getting timer clock rate.
MIPS: ath79: fix regression in PCI window initialization
MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
MIPS: Fix VZ probe gas errors with binutils <2.24
MIPS: perf: Fix I6400 event numbers
MIPS: DEC: Export `ioasic_ssr_lock' to modules
MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
MIPS: CM: Fix compilation error when !MIPS_CM
MIPS: Fix genvdso error on rebuild
USB: ohci-jz4740: Remove obsolete driver
MIPS: JZ4740: Probe OHCI platform device via DT
MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
MIPS: pistachio: Determine SoC revision during boot
MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
MIPS: Prevent "restoration" of MSA context in non-MSA kernels
MIPS: cevt-r4k: Dynamically calculate min_delta_ns
MIPS: malta-time: Take seconds into account
MIPS: malta-time: Start GIC count before syncing to RTC
MIPS: Force CPUs to lose FP context during mode switches
...
Move cpufreq bits for mvebu into drivers/cpufreq/ directory, that's
where they really belong to.
Compiled tested only.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Multiple platforms are using the generic cpufreq-dt driver now, and all
of them are required to create a platform device with name "cpufreq-dt",
in order to get the cpufreq-dt probed.
Many of them do it from platform code, others have special drivers just
to do that.
It would be more sensible to do this at a generic place, where all such
platform can mark their entries.
This patch adds a separate file to get this device created. Currently
the compat list of platforms that we support is empty, and will be
filled in as and when we move platforms to use it.
It always compiles as part of the kernel and so doesn't need a
module-exit operation.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move abstract code related to struct gov_attr_set to a separate (new)
file so it can be shared with (future) goverernors that won't share
more code with "ondemand" and "conservative".
No intentional functional changes.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The bootloader is charged with the responsibility to provide platform
specific Dynamic Voltage and Frequency Scaling (DVFS) information via
Device Tree. This driver takes the supplied configuration and
registers it with the new generic OPP framework, to then be used with
CPUFreq.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As we've enabled multiplatform kernels on ARM, and greatly done away with
the contents under arch/arm/mach-*, there's still need for SoC-related
drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate
with power management blocks on these SoCs for use by clock, regulator and
bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be confused with
PSCI (Power State Coordination Interface). SCPI is used to communicate with
the assistant embedded cores doing power management, and we have yet to see
how many of them will implement this for their hardware vs abstracting in
other ways (or not at all like in the past).
- To make confusion between SCPI and PSCI more likely, this release also
includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dm+I
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
* pm-opp:
PM / OPP: passing NULL to PTR_ERR()
PM / OPP: Move cpu specific code to opp/cpu.c
PM / OPP: Move opp core to its own directory
PM / OPP: Prefix exported opp routines with dev_pm_opp_
PM / OPP: Rename opp init/free table routines
PM / OPP: reuse of_parse_phandle()
This driver utilizes the methods introduced in a previous
patch titled - "ACPI: Introduce CPU performance controls using CPPC"
and enables usage with existing CPUFreq governors.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Reviewed-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control including CPU DVFS. SCPI Message Protocol is used to
communicate with the SCPI.
This patch adds a interface driver for adding OPPs and registering
the arm_big_little cpufreq driver for such systems.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
OPP code is expanding and is already present in multiple directories
(cpufreq and power). Lets move it to its own directory, to manage it
better.
This also moves/renames the cpufreq_opp file to cpu.c, as it will
contain helpers for cpu device. Its not just about cpufreq, other
frameworks can use OPPs as well.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is a collection of a few late fixes and other misc. stuff that
had dependencies on things being merged from other trees.
The bulk of the changes are for samsung/exynos SoCs for some changes
that needed a few minor reworks so ended up a bit late. The others
are mainly for qcom SoCs: a couple fixes and some DTS updates.
There's one conflict with drivers/cpufreq/exynos-cpufreq.c because
it's now been completely removed, but there were some fixes that hit
mainline in the meantime.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=85Ck
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM SoC updates from Kevin Hilman:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The bulk of the changes are for samsung/exynos SoCs for some changes
that needed a few minor reworks so ended up a bit late. The others
are mainly for qcom SoCs: a couple fixes and some DTS updates"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: multi_v7_defconfig: Enable PBIAS regulator
soc: qcom: smd: Correct fBLOCKREADINTR handling
soc: qcom: smd: Use correct remote processor ID
soc: qcom: smem: Fix errant private access
ARM: dts: qcom: msm8974-sony-xperia-honami: Use stdout-path
ARM: dts: qcom: msm8960-cdp: Use stdout-path
ARM: dts: qcom: msm8660-surf: Use stdout-path
ARM: dts: qcom: ipq8064-ap148: Use stdout-path
ARM: dts: qcom: apq8084-mtp: Use stdout-path
ARM: dts: qcom: apq8084-ifc6540: Use stdout-path
ARM: dts: qcom: apq8074-dragonboard: Use stdout-path
ARM: dts: qcom: apq8064-ifc6410: Use stdout-path
ARM: dts: qcom: apq8064-cm-qs600: Use stdout-path
ARM: dts: qcom: Label serial nodes for aliasing and stdout-path
reset: ath79: Fix missing spin_lock_init
reset: Add (devm_)reset_control_get stub functions
ARM: EXYNOS: switch to using generic cpufreq driver for exynos4x12
cpufreq: exynos: Remove unselectable rule for arm-exynos-cpufreq.o
ARM: dts: add iommu property to JPEG device for exynos4
ARM: dts: enable SPI1 for exynos4412-odroidu3
...
Huang Rui
Hector.Yuan
Linus Torvalds
Andy Shevchenko
Arnd Bergmann
Rafael J. Wysocki
Sumit Gupta
Mike Rapoport
Sudeep Holla
Viresh Kumar
Sricharan R
Yangtao Li
Nicolas Saenz Julienne
Leonard Crestez
Gregory CLEMENT
Taniya Das
Krzysztof Kozlowski
Ilia Lin
Corentin LABBE
Gregory CLEMENT
Greg Kroah-Hartman
Linus Walleij
Marc Gonzalez
Sean Wang
Mikko Perttunen
Dave Gerlach
Markus Mayer
Kelvin Cheung
Lee Jones
Ashwin Chaugule