These devices have accelerometers. To report accelerometer coordinates, a new
property, INPUT_PROP_ACCELEROMETER, is added.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
After PAD moved to its own interface, there were duplicated statements in
wacom_setup_pentouch_input_capabilities. Merge them together to reduce future
maintenance effort.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
stylus_in_proximity is used to make sure no touch event is sent while pen is in
proximity. touch_down is used to make sure a touch up event is sent when pen
comes into proximity while touch is down.
Two touch routines didn't store touch_down. One touch routine forgot to check
stylus_in_proximity before sending touch events. This patch fixes those issues.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The FF2 driver (usbhid/hid-pidff.c) sends commands to the stick during ff_init.
However, this is called inside a block where driver_input_lock is locked, so
the results of these initial commands are discarded. This behavior is the
"killer", without this nothing else works.
ff_init issues commands using "hid_hw_request". This eventually goes to
hid_input_report, which returns -EBUSY because driver_input_lock is locked. The
change is to delay the ff_init call in hid-core.c until after this lock has
been released.
Calling hid_device_io_start() releases the lock so the device can be
configured. We also need to call hid_device_io_stop() on exit for the lock to
remain locked while ending the init of the drivers.
[ benjamin.tissoires@redhat.com: imrpoved the changelog a lot ]
Signed-off-by: Jim Keir <jimkeir@oracledbadirect.com>
Reviewed-by: Benjamin.tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The return type of wait_for_completion_timeout is unsigned long not
int. This patch fixes up the declarations only.
Patch was compile tested only for x86_64_defconfig + CONFIG_X86_VSMP=y
CONFIG_HYPERV=m, CONFIG_HID_HYPERV_MOUSE=m
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It appears that the Cintiq Companion Hybrid does not send an ABS_MISC event to
userspace when any of its ExpressKeys are pressed. This is not strictly
necessary now that the pad exists on its own device, but should be fixed for
consistency's sake.
Traditionally both the stylus and pad shared the same device node, and
xf86-input-wacom would use ABS_MISC for disambiguation. Not sending this causes
the Hybrid to behave incorrectly with xf86-input-wacom beginning with its
8f44f3 commit.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use <driver>-$(CONFIG_FOO) syntax to build multipart objects with
optional parts, since all the config options are bool. Also, delete the
obvious comments in the usbhid Makefile.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Microchip Pick16F1454 is exported as a HID device and is used by for
example the Yepkit YKUSH three-port switchable USB hub. However, it is not an
actual HID-device. On the Yepkit, it is used to power up/down the ports on the
hub. The HID driver should ignore this device.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the DEVICE_ATTR_RW macro to reduce boiler plate and move the
attribute declaration to get rid of function signatures.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no reason to set the range attribute executable to the user and
group, and writable to the group. Fix the permission to 0644.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some Cintiq and Intuos tablets report In Range event. This event is sent before
valid data is reported when tool enters proximity; or before out of proximity
event is reported when tool exits.
While entering proximity, In Range means a pen is detected. This information
can be used for palm/touch rejection on both pen and touch enabled devices.
While exiting, it means the tool has reached its maximum detectable distance.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Users may use unsupported tools on Cintiq or Intuos. When invalid tools or data
are detected, they should be ignored. That is, no event from those tools should
be reported.
Consolidating that code in wacom_intuos_inout simplifies the logic and make it
easier for future code change.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Have hid-rmi handle all of the Razer Blade HID devices that are part of the
composite USB device. This will allow hid-rmi to operate the touchpad in rmi
mode while passing events from the other devices to hid-input.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The external buttons on HID touchpads are connected as pass through devices and
button events are not reported in the rmi registers. As a result on these
devices we need to allow the HID generic desktop button events to be processed
by hid-input. Unfortunately, there is no way to query the touchpad to determine
that it has pass through buttons so the RMI_DEVICE_HAS_PHYS_BUTTONS should be
set manually when adding the device to rmi_id[].
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that hid_report_len is in hid.h we can use this function instead of
duplicating the code which computes it.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is a static checker fix. We write some binary settings to the
sysfs file. One of the settings is the "->startup_profile". There
isn't any checking to make sure it fits into the
pyra->profile_settings[] array in the profile_activated() function.
I added a check to pyra_sysfs_write_settings() in both places because
I wasn't positive that the other callers were correct.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a disconnect occurs while getting the actual name of the device
(which can take several HID transactions), the name of the device will
be the hid name, provided by the Unifying Receiver.
This means that in some cases, the user space will see a different
name that what it usually sees when there is no disconnect.
We should store the name of the device in the struct hidpp. That way,
if a disconnect occurs while we are accessing the name,
hidpp_connect_event() can fail, and the input node is not created.
The input node will be created only if we have a connection which
lasts long enough to retrieve all the requested information:
name, protocol, and specific configuration.
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Based on code for the US Surface Type Cover 3
from commit be3b16341d
("HID: add support for MS Surface Pro 3 Type Cover"):
Signed-off-by: Alan Wu <alan.c.wu@gmail.com>
Tested-by: Karlis Dreizis <karlisdreizis@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ignore check that got added in 6ce901eb61 ("HID: input: fix confusion
on conflicting mappings") needs to properly check for VARIABLE reports
as well (ARRAY reports should be ignored), otherwise legitimate keyboards
might break.
Cc: <stable@vger.kernel.org>
Fixes: 6ce901eb61 ("HID: input: fix confusion on conflicting mappings")
Reported-by: Fredrik Hallenberg <megahallon@gmail.com>
Reported-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On an PC-101/103/104 keyboard (American layout) the 'Enter' key and its
neighbours look like this:
+---+ +---+ +-------+
| 1 | | 2 | | 5 |
+---+ +---+ +-------+
+---+ +-----------+
| 3 | | 4 |
+---+ +-----------+
On a PC-102/105 keyboard (European layout) it looks like this:
+---+ +---+ +-------+
| 1 | | 2 | | |
+---+ +---+ +-+ 4 |
+---+ +---+ | |
| 3 | | 5 | | |
+---+ +---+ +-----+
(Note that the number of keys is the same, but key '5' is moved down and
the shape of key '4' is changed. Keys '1' to '3' are exactly the same.)
The keys 1-4 report the same scan-code in HID in both layouts, even though
the keysym they produce is usually different depending on the XKB-keymap
used by user-space.
However, key '5' (US 'backslash'/'pipe') reports 0x31 for the upper layout
and 0x32 for the lower layout, as defined by the HID spec. This is highly
confusing as the linux-input API uses a single keycode for both.
So far, this was never a problem as there never has been a keyboard with
both of those keys present at the same time. It would have to look
something like this:
+---+ +---+ +-------+
| 1 | | 2 | | x31 |
+---+ +---+ +-------+
+---+ +---+ +-----+
| 3 | |x32| | 4 |
+---+ +---+ +-----+
HID can represent such a keyboard, but the linux-input API cannot.
Furthermore, any user-space mapping would be confused by this and,
luckily, no-one ever produced such hardware.
Now, the HID input layer fixed this mess by mapping both 0x31 and 0x32 to
the same keycode (KEY_BACKSLASH==0x2b). As only one of both physical keys
is present on a hardware, this works just fine.
Lets introduce hardware-vendors into this:
------------------------------------------
Unfortunately, it seems way to expensive to produce a different device for
American and European layouts. Therefore, hardware-vendors put both keys,
(0x31 and 0x32) on the same keyboard, but only one of them is hooked up
to the physical button, the other one is 'dead'.
This means, they can use the same hardware, with a different button-layout
and automatically produce the correct HID events for American *and*
European layouts. This is unproblematic for normal keyboards, as the
'dead' key will never report any KEY-DOWN events. But RollOver keyboards
send the whole matrix on each key-event, allowing n-key roll-over mode.
This means, we get a 0x31 and 0x32 event on each key-press. One of them
will always be 0, the other reports the real state. As we map both to the
same keycode, we will get spurious key-events, even though the real
key-state never changed.
The easiest way would be to blacklist 'dead' keys and never handle those.
We could simply read the 'country' tag of USB devices and blacklist either
key according to the layout. But... hardware vendors... want the same
device for all countries and thus many of them set 'country' to 0 for all
devices. Meh..
So we have to deal with this properly. As we cannot know which of the keys
is 'dead', we either need a heuristic and track those keys, or we simply
make use of our value-tracking for HID fields. We simply ignore HID events
for absolute data if the data didn't change. As HID tracks events on the
HID level, we haven't done the keycode translation, yet. Therefore, the
'dead' key is tracked independently of the real key, therefore, any events
on it will be ignored.
This patch simply discards any HID events for absolute data if it didn't
change compared to the last report. We need to ignore relative and
buffered-byte reports for obvious reasons. But those cannot be affected by
this bug, so we're fine.
Preferably, we'd do this filtering on the HID-core level. But this might
break a lot of custom drivers, if they do not follow the HID specs.
Therefore, we do this late in hid-input just before we inject it into the
input layer (which does the exact same filtering, but on the keycode
level).
If this turns out to break some devices, we might have to limit filtering
to EV_KEY events. But lets try to do the Right Thing first, and properly
filter any absolute data that didn't change.
This patch is tagged for 'stable' as it fixes a lot of n-key RollOver
hardware. We might wanna wait with backporting for a while, before we know
it doesn't break anything else, though.
Cc: <stable@vger.kernel.org>
Reported-by: Adam Goode <adam@spicenitz.org>
Reported-by: Fredrik Hallenberg <megahallon@gmail.com>
Tested-by: Fredrik Hallenberg <megahallon@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Bamboo Pads are using the generic processing but their report descriptors
differ from the ISDv* line. The pen fields are marked with the .physical
as Digitizer_Pen, which makes also sense.
Add this field to the checks and enable for free Bamboo Pads.
Reported-by: Josep Sanchez Ferreres <josep.sanchez.ferreres@est.fib.upc.edu>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We introduced nice macros in wacom_wac.c to check whether a field is
a pen or a touch one.
wacom_usage_mapping() still uses it's own tests, which are not in sync with
the wacom_wac tests (.application is not checked).
That means that some legitimate fields might be filtered out from the
usage mapping, and thus will not be used properly while receiving the
events.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
New Genius MousePen i608X devices have a new id 0x501a instead of the
old 0x5011 so add a new #define with "_2" appended and change required
places.
The remaining two checkpatch warnings about line length
being over 80 characters are present in the original files too and this
patch was made in the same style (no line break).
Just adding a new id and changing the required places should make the
new device work without any issues according to the bug report in the
following url.
This patch was made according to and fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=67111
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit fc38a8a66e ("HID: add BETOP game controller force feedback support")
is missing the actual addition of drivers/hid/hid-betopff.c due to my
mistake (I forgot to add the file after fixing conflicts).
Fixes: fc38a8a66e ("HID: add BETOP game controller force feedback support")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds force feedback support for BETOP USB game controllers.
These devices are mass produced in China.
Signed-off-by: Huang Bo <huangbobupt@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allowing hid-rmi to bind to non rmi devices allows us to support composite USB
devices which contain several HID devices one of which is a HID touchpad.
Since all of the devices have the same VID and PID we can add the device
to the hid_have_special_driver list and have hid-rmi handle all of the devices.
Then hid-rmi's probe can look for the rmi specific HID report IDs and decide if
it should handle the device as a rmi device or simply report that the events
needs additional processing.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current names are reported as "K750", "M705", and it can be misleading
for the users when they look at their input device list.
Prefixing the names with "Logitech " makes things better.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a return to avoid a fall-through. Introduced in commit
57ac86cf52 ("HID: logitech-hidpp: add
support of the first Logitech Wireless Touchpad").
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Devices speaking HID++ 2.0 report a different error code (0xff). Detect
these errors too to avoid 5 second delays when the device reports an
error. Caught by... well, a bug in the QEMU emulation of this receiver.
Renamed fap to rap for HID++ 1.0 errors because it is more logical,
it has no functional difference.
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allows for HID_BATTERY_STRENGTH config be enabled without the need for HID
module to be built-in, prior to this HID and POWER_SUPPLY had to be equal, and
now we only select POWER_SUPPLY and depend on the HID module.
Signed-off-by: Daniel Nicoletti <dantti12@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current names are reported as "K750", "M705", and it can be misleading
for the users when they look at their input device list.
Prefixing the names with "Logitech " makes things better.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When a hid driver that uses i2c-hid as transport is unloaded, the hid core
will call i2c_hid_stop() which releases all the buffers associated with the
device. This includes also the command buffer.
Now, when the i2c-hid driver itself is unloaded it tries to power down the
device by sending it PWR_SLEEP command. Since the command buffer is already
released we get following crash:
[ 79.691459] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 79.691532] IP: [<ffffffffa05bc049>] __i2c_hid_command+0x49/0x310 [i2c_hid]
...
[ 79.693467] Call Trace:
[ 79.693494] [<ffffffff810424e1>] ? __unmask_ioapic+0x21/0x30
[ 79.693537] [<ffffffff81042855>] ? unmask_ioapic+0x25/0x40
[ 79.693581] [<ffffffffa05bc35b>] ? i2c_hid_set_power+0x4b/0xa0 [i2c_hid]
[ 79.693632] [<ffffffffa05bc3cf>] ? i2c_hid_runtime_resume+0x1f/0x30 [i2c_hid]
[ 79.693689] [<ffffffff814c08fb>] ? __rpm_callback+0x2b/0x70
[ 79.693733] [<ffffffff814c0961>] ? rpm_callback+0x21/0x90
[ 79.693776] [<ffffffff814c0dec>] ? rpm_resume+0x41c/0x600
[ 79.693820] [<ffffffff814c1e1c>] ? __pm_runtime_resume+0x4c/0x80
[ 79.693868] [<ffffffff814b8588>] ? __device_release_driver+0x28/0x100
[ 79.693917] [<ffffffff814b8d90>] ? driver_detach+0xa0/0xb0
[ 79.693959] [<ffffffff814b82cc>] ? bus_remove_driver+0x4c/0xb0
[ 79.694006] [<ffffffff810d1cfd>] ? SyS_delete_module+0x11d/0x1d0
[ 79.694054] [<ffffffff8165f107>] ? int_signal+0x12/0x17
[ 79.694095] [<ffffffff8165ee69>] ? system_call_fastpath+0x12/0x17
Fix this so that we only free buffers when the i2c-hid driver itself is
removed.
Fixes: 34f439e4af ("HID: i2c-hid: add runtime PM support")
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On composite HID devices there may be multiple HID devices on separate
interfaces, but hid-rmi should only bind to the touchpad. The previous version
simply checked that the interface protocol was set to mouse. Unfortuately, it
is not always the case that the touchpad has the mouse interface protocol set.
This patch takes a different approach and scans the report descriptor looking
for the Generic Desktop Pointer usage and the Vendor Specific Top Level
Collection needed by the hid-rmi driver to interface with the device.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If wtp_connect() fails, that means most of the time that the device has
been disconnected. Subsequent attempts to contact the device will fail
too, so it's simpler to bail out earlier.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Apple bluetooth wireless keyboard (sold in UK) has always reported zero
for battery strength no matter what condition the batteries are actually
in. With this patch applied (applying same quirk as other Apple
keyboards), the battery strength is now correctly reported.
Signed-off-by: Karl Relton <karllinuxtest.relton@ntlworld.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
By default the middle button is in a compatibility mode, and generates
standard wheel events when dragging with the middle trackpoint button.
Unfortunately this is buggy:
* The middle button comes up before starting wheel events, causing a middle
click on whatever the mouse cursor was sitting on
* The USB keyboard always generates the "native" horizontal wheel event,
regardless of mode.
Instead, enable the "native" mode the Windows driver uses, and add support
for the custom events this generates. This fixes the USB keyboard wheel
events, and the middle-click up event comes after the wheel events.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The trackpoint sensitivity can also be controlled, expose this via
sysfs.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously wtp_raw_event would be called through
hidpp_raw_hidpp_event (for the touchpad report) and hidpp_raw_event
(for the mouse report).
This patch removes one calling surface, making a clearer distinction
between "generic HID++ processing" (matching internal reports) and
device-specific event processing.
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Malicious USB devices can send bogus reports smaller than the expected
buffer size. Ensure that the length for WTP reports is valid to avoid
reading out of bounds.
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Malicious USB devices can send bogus reports smaller than the expected
buffer size. Ensure that the length is valid to avoid reading out of
bounds.
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID updates from Jiri Kosina:
- i2c-hid race condition fix from Jean-Baptiste Maneyrol
- Logitech driver now supports vendor-specific HID++ protocol, allowing
us to deliver a full multitouch support on wider range of Logitech
touchpads. Written by Benjamin Tissoires
- MS Surface Pro 3 Type Cover support added by Alan Wu
- RMI touchpad support improvements from Andrew Duggan
- a lot of updates to Wacom driver from Jason Gerecke and Ping Cheng
- various small fixes all over the place
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (56 commits)
HID: rmi: The address of query8 must be calculated based on which query registers are present
HID: rmi: Check for additional ACM registers appended to F11 data report
HID: i2c-hid: prevent buffer overflow in early IRQ
HID: logitech-hidpp: disable io in probe error path
HID: logitech-hidpp: add boundary check for name retrieval
HID: logitech-hidpp: check name retrieval return code
HID: logitech-hidpp: do not return the name length
HID: wacom: Report input events for each finger on generic devices
HID: wacom: Initialize MT slots for generic devices at post_parse_hid
HID: wacom: Update maximum X/Y accounding to outbound offset
HID: wacom: Add support for DTU-1031X
HID: wacom: add defines for new Cintiq and DTU outbound tracking
HID: wacom: fix freeze on open when autosuspend is on
HID: wacom: re-add accidentally dropped Lenovo PID
HID: make hid_report_len as a static inline function in hid.h
HID: wacom: Consult the application usage when determining field type
HID: wacom: PAD is independent with pen/touch
HID: multitouch: Add quirk for VTL touch panels
HID: i2c-hid: fix race condition reading reports
HID: wacom: Add angular resolution data to some ABS axes
...
If a touchpad does not report relative data then query 6 will not be present and the address
of query 8 will be one less. This patches calculates the location of query 8 instead of
hardcoding the offset.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a touchpad reports the F11 data40 register then this indicates that the touchpad reports
additional ACM (Accidental Contact Mitigation) data after the F11 data in the HID attention
report. These additional bytes shift the position of the F30 button data causing the driver
to incorrectly report button state when this functionality is present. This patch accounts
for the additional data in the report.
Fixes:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1398533
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Before ->start() is called, bufsize size is set to HID_MIN_BUFFER_SIZE,
64 bytes. While processing the IRQ, we were asking to receive up to
wMaxInputLength bytes, which can be bigger than 64 bytes.
Later, when ->start is run, a proper bufsize will be calculated.
Given wMaxInputLength is said to be unreliable in other part of the
code, set to receive only what we can even if it results in truncated
reports.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Balance a hid_device_io_start() call with hid_device_io_stop() in the
error path. This avoids processing of HID reports when the probe fails
which possibly leads to invalid memory access in hid_device_probe() as
report_enum->report_id_hash might already be freed via
hid_close_report().
hid_set_drvdata() is called before wtp_allocate, be consistent and clear
drvdata too on the error path of wtp_allocate.
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jiri Kosina
Ping Cheng
Jim Keir
Nicholas Mc Guire
Jason Gerecke
Michal Marek
Kristian Evensen
Vivien Didelot
Andrew Duggan
Dan Carpenter
Benjamin Tissoires
Alan Wu
Ross Skaliotis
Geert Uytterhoeven
David Herrmann
Giedrius Statkevičius
Huang Bo
Peter Wu
Daniel Nicoletti
Mika Westerberg
Karl Relton
Jamie Lentin
Linus Torvalds
Gwendal Grignou