When we free a vmapped buffer, we need to ensure the vmap address
and length we free is the same as when it was allocated. In various
places in the log code we change the memory the buffer is pointing
to before issuing IO, but we never reset the buffer to point back to
it's original memory (or no memory, if that is the case for the
buffer).
As a result, when we free the buffer it points to memory that is
owned by something else and attempts to unmap and free it. Because
the range does not match any known mapped range, it can trigger
BUG_ON() traps in the vmap code, and potentially corrupt the vmap
area tracking.
Fix this by always resetting these buffers to their original state
before freeing them.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Convert the xfs log operations to use the new error logging
interfaces. This removes the xlog_{warn,panic} wrappers and makes
almost all errors emit the device they belong to instead of just
refering to "XFS".
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
We currently have a global error message buffer in cmn_err that is
protected by a spin lock that disables interrupts. Recently there
have been reports of NMI timeouts occurring when the console is
being flooded by SCSI error reports due to cmn_err() getting stuck
trying to print to the console while holding this lock (i.e. with
interrupts disabled). The NMI watchdog is seeing this CPU as
non-responding and so is triggering a panic. While the trigger for
the reported case is SCSI errors, pretty much anything that spams
the kernel log could cause this to occur.
Realistically the only reason that we have the intemediate message
buffer is to prepend the correct kernel log level prefix to the log
message. The only reason we have the lock is to protect the global
message buffer and the only reason the message buffer is global is
to keep it off the stack. Hence if we can avoid needing a global
message buffer we avoid needing the lock, and we can do this with a
small amount of cleanup and some preprocessor tricks:
1. clean up xfs_cmn_err() panic mask functionality to avoid
needing debug code in xfs_cmn_err()
2. remove the couple of "!" message prefixes that still exist that
the existing cmn_err() code steps over.
3. redefine CE_* levels directly to KERN_*
4. redefine cmn_err() and friends to use printk() directly
via variable argument length macros.
By doing this, we can completely remove the cmn_err() code and the
lock that is causing the problems, and rely solely on printk()
serialisation to ensure that we don't get garbled messages.
A series of followup patches is really needed to clean up all the
cmn_err() calls and related messages properly, but that results in a
series that is not easily back portable to enterprise kernels. Hence
this initial fix is only to address the direct problem in the lowest
impact way possible.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
log->l_tail_lsn is currently protected by the log grant lock. The
lock is only needed for serialising readers against writers, so we
don't really need the lock if we make the l_tail_lsn variable an
atomic. Converting the l_tail_lsn variable to an atomic64_t means we
can start to peel back the grant lock from various operations.
Also, provide functions to safely crack an atomic LSN variable into
it's component pieces and to recombined the components into an
atomic variable. Use them where appropriate.
This also removes the need for explicitly holding a spinlock to read
the l_tail_lsn on 32 bit platforms.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
log->l_last_sync_lsn is updated in only one critical spot - log
buffer Io completion - and is protected by the grant lock here. This
requires the grant lock to be taken for every log buffer IO
completion. Converting the l_last_sync_lsn variable to an atomic64_t
means that we do not need to take the grant lock in log buffer IO
completion to update it.
This also removes the need for explicitly holding a spinlock to read
the l_last_sync_lsn on 32 bit platforms.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Prepare for switching the grant heads to atomic variables by
combining the two 32 bit values that make up the grant head into a
single 64 bit variable. Provide wrapper functions to combine and
split the grant heads appropriately for calculations and use them as
necessary.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
We now have two copies of AIL insert operations that are mostly
duplicate functionality. The single log item updates can be
implemented via the bulk updates by turning xfs_trans_ail_update()
into a simple wrapper. This removes all the duplicate insert
functionality and associated helpers.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
EFI/EFD interactions are protected from races by the AIL lock. They
are the only type of log items that require the the AIL lock to
serialise internal state, so they need to be separated from the AIL
lock before we can do bulk insert operations on the AIL.
To acheive this, convert the counter of the number of extents in the
EFI to an atomic so it can be safely manipulated by EFD processing
without locks. Also, convert the EFI state flag manipulations to use
atomic bit operations so no locks are needed to record state
changes. Finally, use the state bits to determine when it is safe to
free the EFI and clean up the code to do this neatly.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Dispatch to a different helper for phase1 vs phase2 in
xlog_recover_commit_trans instead of doing it in all the
low-level functions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Merge the call to xlog_recover_reorder_trans and the loop over the
recovery items from xlog_recover_do_trans into xlog_recover_commit_trans,
and keep the switch statement over the log item types as a separate helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
XFS used to support different types of buffer log items long time
ago. Remove the switch statements checking the log item type in
various buffer recovery helpers that were left over from those days
and the rather useless xlog_recover_do_buffer_pass2 wrapper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Stop having two different names for many buffer functions and use
the more descriptive xfs_buf_* names directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Each buffer contains both a buftarg pointer and a mount pointer. If
we add a mount pointer into the buftarg, we can avoid needing the
b_mount field in every buffer and grab it from the buftarg when
needed instead. This shrinks the xfs_buf by 8 bytes.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
xfs_buf_get_nodaddr() is really used to allocate a buffer that is
uncached. While it is not directly assigned a disk address, the fact
that they are not cached is a more important distinction. With the
upcoming uncached buffer read primitive, we should be consistent
with this disctinction.
While there, make page allocation in xfs_buf_get_nodaddr() safe
against memory reclaim re-entrancy into the filesystem by allowing
a flags parameter to be passed.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
By making this member a void pointer we can get rid of a lot of pointless
casts.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Dmapi support was never merged upstream, but we still have a lot of hooks
bloating XFS for it, all over the fast pathes of the filesystem.
This patch drops over 700 lines of dmapi overhead. If we'll ever get HSM
support in mainline at least the namespace events can be done much saner
in the VFS instead of the individual filesystem, so it's not like this
is much help for future work.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
The block number comes from bulkstat based inode lookups to shortcut
the mapping calculations. We ar enot able to trust anything from
bulkstat, so drop the block number as well so that the correct
lookups and mappings are always done.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Add suggested cleanups to commit 29db3370a1369541d58d692fbfb168b8a0bd7f41
from review that didn't end up being commited.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Clean up the buffer log format (XFS_BLI_*) flags because they have a
polluted namespace. They XFS_BLI_ prefix is used for both in-memory
and on-disk flag feilds, but have overlapping values for different
flags. Rename the buffer log format flags to use the XFS_BLF_*
prefix to avoid confusing them with the in-memory XFS_BLI_* prefixed
flags.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
There remains only one user of the l_sectbb_mask field in the log
structure. Just kill it off and compute the mask where needed from
the power-of-2 sector size.
(Only update from last post is to accomodate the changes in the
previous patch in the series.)
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Change struct log so it keeps track of the size (in basic blocks) of
a log sector in l_sectBBsize rather than the log-base-2 of that
value (previously, l_sectbb_log). The name was chosen for
consistency with the other fields in the structure that represent
a number of basic blocks.
(Updated so that a variable used in computing and verifying a log's
sector size is named "log2_size". Also added the "BB" to the
structure field name, based on feedback from Eric Sandeen. Also
dropped some superfluous parentheses.)
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
This can't be enabled through the build system and has been dead for
ages. Note that the CRC patches add back log checksumming, but the
code is quite different from the version removed here anyway.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Odds and ends in "xfs_log_recover.c". This patch just contains some
minor things that didn't seem to warrant their own individual
patches:
- In xlog_bread_noalign(), drop an assertion that a pointer is
non-null (the crash will tell us it was a bad pointer).
- Add a more descriptive header comment for xlog_find_verify_cycle().
- Make a few additions to the comments in xlog_find_head(). Also
rearrange some expressions in a few spots to produce the same
result, but in a way that seems more clear what's being computed.
(Updated in response to Dave's review comments. Note I did not
split this patch like I said I would.)
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In xlog_find_cycle_start() use a local variable for some repeated
operations rather than constantly accessing the memory location
whose address is passed in.
(This version drops an assertion that a pointer is non-null.)
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Rename a label used in xlog_find_head() that I thought was poorly
chosen. Also combine two adjacent labels xlog_find_tail() into a
single label, and give it a more generic name.
(Now using Dave's suggested "validate_head" name for first label.)
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
There are a number of places where a log sector size of 1 uses
special case code. The round_up() and round_down() macros
produce the correct result even when the log sector size is 1, and
this eliminates the need for treating this as a special case.
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Define a function that encapsulates checking the validity of a log
block count.
(Updated from previous version--no longer includes error reporting in the
encapsulated validation function.)
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
XLOG_SECTOR_ROUNDUP_BBCOUNT() and XLOG_SECTOR_ROUNDDOWN_BLKNO()
are now fairly simple macro translations. Just get rid of them in
favor of the round_up() and round_down() macro calls they represent.
Also, in spots in xlog_get_bp() and xlog_write_log_records(),
round_up() was being called with value 1, which just evaluates
to the macro's second argument; so just use that instead.
In the latter case, make use of that value, as long as it's
already been computed.
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
XLOG_SECTOR_ROUNDUP_BBCOUNT() is defined in "fs/xfs/xfs_log_recover.c"
in an overly-complicated way. It is basically roundup(), but that
is not at all clear from its definition. (Actually, there is
another macro round_up() that applies for power-of-two-based masks
which I'll be using here.)
The operands in XLOG_SECTOR_ROUNDUP_BBCOUNT() are basically the
block number (bbs) and the log sector basic block mask
(log->l_sectbb_mask). I'll call them B and M for this discussion.
The macro computes is value this way:
M && (B & M) ? (B + M + 1) & ~M : B
Put another way, we can break it into 3 cases:
1) ! M -> B # 0 mask, no effect
2) ! (B & M) -> B # sector aligned
3) M && (B & M) -> (B + M + 1) & ~M # round up otherwise
The round_up() macro is cleverly defined using a value, v, and a
power-of-2, p, and the result is the nearest multiple of p greater
than or equal to v. Its value is computed something like this:
((v - 1) | (p - 1)) + 1
Let's consider using this in the context of the 3 cases above.
When p = 2^0 = 1, the result boils down to ((v - 1) | 0) + 1, so it
just translates any value v to itself. That handles case (1) above.
When p = 2^n, n > 0, we know that (p - 1) will be a mask with all n
bits 0..n-1 set. The condition in this case occurs when none of
those mask bits is set in the value v provided. If that is the
case, subtracting 1 from v will have 1's in all those lower bits (at
least). Therefore, OR-ing the mask with that decremented value has
no effect, so adding the 1 back again will just translate the v to
itself. This handles case (2).
Otherwise, the value v is greater than some multiple of p, and
decrementing it will produce a result greater than or equal to that
multiple. OR-ing in the mask will produce a value 1 less than the
next multiple of p, so finally adding 1 back will result in the
desired rounded-up value. This handles case (3).
Hopefully this is convincing.
While I was at it, I converted XLOG_SECTOR_ROUNDDOWN_BLKNO() to use
the round_down() macro.
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
This fixes a bug in two places that I found by inspection. In
xlog_find_verify_cycle() and xlog_write_log_records(), the code
attempts to allocate a buffer to hold as many blocks as possible.
It gives up if the number of blocks to be allocated gets too small.
Right now it uses log->l_sectbb_log as that lower bound, but I'm
sure it's supposed to be the actual log sector size instead. That
is, the lower bound should be (1 << log->l_sectbb_log).
Also define a simple macro xlog_sectbb(log) to represent the number
of basic blocks in a sector for the given log.
(No change from original submission; I have implemented Christoph's
suggestion about storing l_sectsize rather than l_sectbb_log in
a new, separate patch in this series.)
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Currently there is no tracing in log recovery, so it is difficult to
determine what is going on when something goes wrong.
Add tracing for log item recovery to provide visibility into the log
recovery process. The tracing added shows regions being extracted
from the log transactions and added to the transaction hash forming
recovery items, followed by the reordering, cancelling and finally
recovery of the items.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Remove the XFS_LOG_FORCE argument which was always set, and the
XFS_LOG_URGE define, which was never used.
Split xfs_log_force into a two helpers - xfs_log_force which forces
the whole log, and xfs_log_force_lsn which forces up to the
specified LSN. The underlying implementations already were entirely
separate, as were the users.
Also re-indent the new _xfs_log_force/_xfs_log_force which
previously had a weird coding style.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Currently we define aliases for the buffer flags in various
namespaces, which only adds confusion. Remove all but the XBF_
flags to clean this up a bit.
Note that we still abuse XFS_B_ASYNC/XBF_ASYNC for some non-buffer
uses, but I'll clean that up later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Remove the roll-your-own linked list operations.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Just minor housekeeping, a lot more functions can be trivially made
static; others could if we reordered things a bit...
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Alex Elder <aelder@sgi.com>
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: event tracing support
xfs: change the xfs_iext_insert / xfs_iext_remove
xfs: cleanup bmap extent state macros
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Alex Elder <aelder@sgi.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert the old xfs tracing support that could only be used with the
out of tree kdb and xfsidbg patches to use the generic event tracer.
To use it make sure CONFIG_EVENT_TRACING is enabled and then enable
all xfs trace channels by:
echo 1 > /sys/kernel/debug/tracing/events/xfs/enable
or alternatively enable single events by just doing the same in one
event subdirectory, e.g.
echo 1 > /sys/kernel/debug/tracing/events/xfs/xfs_ihold/enable
or set more complex filters, etc. In Documentation/trace/events.txt
all this is desctribed in more detail. To reads the events do a
cat /sys/kernel/debug/tracing/trace
Compared to the last posting this patch converts the tracing mostly to
the one tracepoint per callsite model that other users of the new
tracing facility also employ. This allows a very fine-grained control
of the tracing, a cleaner output of the traces and also enables the
perf tool to use each tracepoint as a virtual performance counter,
allowing us to e.g. count how often certain workloads git various
spots in XFS. Take a look at
http://lwn.net/Articles/346470/
for some examples.
Also the btree tracing isn't included at all yet, as it will require
additional core tracing features not in mainline yet, I plan to
deliver it later.
And the really nice thing about this patch is that it actually removes
many lines of code while adding this nice functionality:
fs/xfs/Makefile | 8
fs/xfs/linux-2.6/xfs_acl.c | 1
fs/xfs/linux-2.6/xfs_aops.c | 52 -
fs/xfs/linux-2.6/xfs_aops.h | 2
fs/xfs/linux-2.6/xfs_buf.c | 117 +--
fs/xfs/linux-2.6/xfs_buf.h | 33
fs/xfs/linux-2.6/xfs_fs_subr.c | 3
fs/xfs/linux-2.6/xfs_ioctl.c | 1
fs/xfs/linux-2.6/xfs_ioctl32.c | 1
fs/xfs/linux-2.6/xfs_iops.c | 1
fs/xfs/linux-2.6/xfs_linux.h | 1
fs/xfs/linux-2.6/xfs_lrw.c | 87 --
fs/xfs/linux-2.6/xfs_lrw.h | 45 -
fs/xfs/linux-2.6/xfs_super.c | 104 ---
fs/xfs/linux-2.6/xfs_super.h | 7
fs/xfs/linux-2.6/xfs_sync.c | 1
fs/xfs/linux-2.6/xfs_trace.c | 75 ++
fs/xfs/linux-2.6/xfs_trace.h | 1369 +++++++++++++++++++++++++++++++++++++++++
fs/xfs/linux-2.6/xfs_vnode.h | 4
fs/xfs/quota/xfs_dquot.c | 110 ---
fs/xfs/quota/xfs_dquot.h | 21
fs/xfs/quota/xfs_qm.c | 40 -
fs/xfs/quota/xfs_qm_syscalls.c | 4
fs/xfs/support/ktrace.c | 323 ---------
fs/xfs/support/ktrace.h | 85 --
fs/xfs/xfs.h | 16
fs/xfs/xfs_ag.h | 14
fs/xfs/xfs_alloc.c | 230 +-----
fs/xfs/xfs_alloc.h | 27
fs/xfs/xfs_alloc_btree.c | 1
fs/xfs/xfs_attr.c | 107 ---
fs/xfs/xfs_attr.h | 10
fs/xfs/xfs_attr_leaf.c | 14
fs/xfs/xfs_attr_sf.h | 40 -
fs/xfs/xfs_bmap.c | 507 +++------------
fs/xfs/xfs_bmap.h | 49 -
fs/xfs/xfs_bmap_btree.c | 6
fs/xfs/xfs_btree.c | 5
fs/xfs/xfs_btree_trace.h | 17
fs/xfs/xfs_buf_item.c | 87 --
fs/xfs/xfs_buf_item.h | 20
fs/xfs/xfs_da_btree.c | 3
fs/xfs/xfs_da_btree.h | 7
fs/xfs/xfs_dfrag.c | 2
fs/xfs/xfs_dir2.c | 8
fs/xfs/xfs_dir2_block.c | 20
fs/xfs/xfs_dir2_leaf.c | 21
fs/xfs/xfs_dir2_node.c | 27
fs/xfs/xfs_dir2_sf.c | 26
fs/xfs/xfs_dir2_trace.c | 216 ------
fs/xfs/xfs_dir2_trace.h | 72 --
fs/xfs/xfs_filestream.c | 8
fs/xfs/xfs_fsops.c | 2
fs/xfs/xfs_iget.c | 111 ---
fs/xfs/xfs_inode.c | 67 --
fs/xfs/xfs_inode.h | 76 --
fs/xfs/xfs_inode_item.c | 5
fs/xfs/xfs_iomap.c | 85 --
fs/xfs/xfs_iomap.h | 8
fs/xfs/xfs_log.c | 181 +----
fs/xfs/xfs_log_priv.h | 20
fs/xfs/xfs_log_recover.c | 1
fs/xfs/xfs_mount.c | 2
fs/xfs/xfs_quota.h | 8
fs/xfs/xfs_rename.c | 1
fs/xfs/xfs_rtalloc.c | 1
fs/xfs/xfs_rw.c | 3
fs/xfs/xfs_trans.h | 47 +
fs/xfs/xfs_trans_buf.c | 62 -
fs/xfs/xfs_vnodeops.c | 8
70 files changed, 2151 insertions(+), 2592 deletions(-)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Currently the low-level buffer cache interfaces are highly confusing
as we have a _flags variant of each that does actually respect the
flags, and one without _flags which has a flags argument that gets
ignored and overriden with a default set. Given that very few places
use the default arguments get rid of the duplication and convert all
callers to pass the flags explicitly. Also remove the now confusing
_flags postfix.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Summary of problem:
If a journal record wraps at the physical end of the journal, it has to be
read in two parts in xlog_do_recovery_pass(): a read at the physical end and a
read at the physical beginning. If xlog_bread() has to re-align the first
read, the second read request does not take that re-alignment into account.
If the first read was re-aligned, the second read over-writes the end of the
data from the first read, effectively corrupting it. This can happen either
when reading the record header or reading the record data.
The first sanity check in xlog_recover_process_data() is to check for a valid
clientid, so that is the error reported.
Summary of fix:
If there was a first read at the physical end, XFS_BUF_PTR() returns where the
data was requested to begin. Conversely, because it is the result of
xlog_align(), offset indicates where the requested data for the first read
actually begins - whether or not xlog_bread() has re-aligned it.
Using offset as the base for the calculation of where to place the second read
data ensures that it will be correctly placed immediately following the data
from the first read instead of sometimes over-writing the end of it.
The attached patch has resolved the reported problem of occasional inability
to recover the journal (reporting "bad clientid").
Signed-off-by: Andy Poling <andy@realbig.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Hi,
I was hit by a bug in linux 2.6.31 when XFS is not able to recover the
log after a crash if fs was mounted with quotas. Gory details in XFS
bugzilla: http://oss.sgi.com/bugzilla/show_bug.cgi?id=855.
It looks like wrong struct is used in buffer length check, and the following
patch should fix the problem.
xfs_dqblk_t has a size of 104+32 bytes, while xfs_disk_dquot_t is 104 bytes
long, and this is exactly what I see in system logs - "XFS: dquot too small
(104) in xlog_recover_do_dquot_trans."
Signed-off-by: Jan Rekorajski <baggins@sith.mimuw.edu.pl>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
A lot more functions could be made static, but they need
forward declarations; this does some easy ones, and also
found a few unused functions in the process.
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Arkadiusz has seen really strange crashes in xfs_qm_dqcheck that
I can only explain by a log item being too smal to actually fit the
xfs_dqblk_t we're dereferencing all over xfs_qm_dqcheck. So add
graceful checks for NULL or too small quota items to the log recovery
code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Most callers of xlog_bread need to call xlog_align to get the actual offset.
Consolidate that call into the main xlog_bread and provide a _xlog_bread
for those few that don't want the actual offset.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Change the big if-elsif-else block handling the different item types
into a more natural switch, remove assignments in conditionals and
remove an out of place comment from centuries ago on IRIX.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
There's another little snipplet of code left from the handling of the old
inode log item format in xlog_recover_do_inode_trans. Kill it as it
can't be reached anymore.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Andras Korn reported an oops on log replay causes by a corrupted
xfs_inode_log_format_t passing a 0 size to kmem_zalloc. This patch handles
to small or too large numbers of log regions gracefully by rejecting the
log replay with a useful error message.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Andras Korn <korn-sgi.com@chardonnay.math.bme.hu>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Just another set of types obsfucating the code, remove them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Before trying to obtain, read or write a buffer,
check that the buffer length is actually valid. If
it is not valid, then something read in the recovery
process has been corrupted and we should abort
recovery.
Reported-by: Eric Sesterhenn <snakebyte@gmx.de>
Tested-by: Eric Sesterhenn <snakebyte@gmx.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Replace the b_fspriv pointer and it's ugly accessors with a properly types
xfs_mount pointer. Also switch log reocvery over to it instead of using
b_fspriv for the mount pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
If we fail after xfs_iget we have to drop the reference count, spotted
by Dave Chinner. Also remove some useless asserts and stop trying to
deal with di_mode == 0 inodes because never gets those without passing
the IGET_CREATE flag to xfs_iget.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Most uses of struct xfs_imap are to map and inode to a buffer. To avoid
copying around the inode location information we should just embedd a
strcut xfs_imap into the xfs_inode. To make sure it doesn't bloat an
inode the im_len is changed to a ushort, which is fine as that's what
the users exepect anyway.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
We have removed the support for old-style inode items a while ago and
xlog_recover_do_inode_trans is now only called for XFS_LI_INODE items.
That means we can remove the call to xfs_imap there and with it the
XFS_IMAP_LOOKUP that is set by all other callers. We can also mark
xfs_imap static now.
(First sent on October 21st)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
The only caller of xfs_itobp that doesn't have i_blkno setup is now
the initial inode read. It needs access to the whole xfs_imap so using
xfs_inotobp is not an option. Instead opencode the buffer lookup in
xfs_iread and kill all the functionality for the initial map from
xfs_itobp.
(First sent on October 21st)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Split out the body of the main loop into a separate helper to make the
code readable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Now that we have a separate xfs_icdinode_t for the in-core inode which
gets logged there is no need anymore for the xfs_dinode vs xfs_dinode_core
split - the fact that part of the structure gets logged through the inode
log item and a small part not can better be described in a comment.
All sizeof operations on the dinode_core either really wanted the
icdinode and are switched to that one, or had already added the size
of the agi unlinked list pointer. Later both will be replaced with
helpers once we get the larger CRC-enabled dinode.
Removing the data and attribute fork unions also has the advantage that
xfs_dinode.h doesn't need to pull in every header under the sun.
While we're at it also add some more comments describing the dinode
structure.
(First sent on October 7th)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Move all fields from xlog_iclog_fields_t into xlog_in_core_t instead of having
them in a substructure and the using #defines to make it look like they were
directly in xlog_in_core_t. Also document that xlog_in_core_2_t is grossly
misnamed, and make all references to it typesafe.
(First sent on Semptember 15th)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Add a helper to read the AGF header and perform basic verification.
Based on hunks from a larger patch from Dave Chinner.
(First sent on Juli 23rd)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Add a helper to read the AGI header and perform basic verification.
Based on hunks from a larger patch from Dave Chinner.
(First sent on Juli 23rd)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
When we are about to add a new item to a transaction in recovery, we need
to check that it is valid first. Currently we just assert that header
magic number matches, but in production systems that is not present and we
add a corrupted transaction to the list to be processed. This results in a
kernel oops later when processing the corrupted transaction.
Instead, if we detect a corrupted transaction, abort recovery and leave
the user to clean up the mess that has occurred.
SGI-PV: 988145
SGI-Modid: xfs-linux-melb:xfs-kern:32356a
Signed-off-by: David Chinner <david@fromorbit.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Change all the remaining AIL API functions that are passed struct
xfs_mount pointers to pass pointers directly to the struct xfs_ail being
used. With this conversion, all external access to the AIL is via the
struct xfs_ail. Hence the operation and referencing of the AIL is almost
entirely independent of the xfs_mount that is using it - it is now much
more tightly tied to the log and the items it is tracking in the log than
it is tied to the xfs_mount.
SGI-PV: 988143
SGI-Modid: xfs-linux-melb:xfs-kern:32353a
Signed-off-by: David Chinner <david@fromorbit.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
When we need to go from the log to the AIL, we have to go via the
xfs_mount. Add a xfs_ail pointer to the log so we can go directly to the
AIL associated with the log.
SGI-PV: 988143
SGI-Modid: xfs-linux-melb:xfs-kern:32351a
Signed-off-by: David Chinner <david@fromorbit.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Bring the ail lock inside the struct xfs_ail. This means the AIL can be
entirely manipulated via the struct xfs_ail rather than needing both the
struct xfs_mount and the struct xfs_ail.
SGI-PV: 988143
SGI-Modid: xfs-linux-melb:xfs-kern:32350a
Signed-off-by: David Chinner <david@fromorbit.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
With the new cursor interface, it makes sense to make all the traversing
code use the cursor interface and make the old one go away. This means
more of the AIL interfacing is done by passing struct xfs_ail pointers
around the place instead of struct xfs_mount pointers.
We can replace the use of xfs_trans_first_ail() in xfs_log_need_covered()
as it is only checking if the AIL is empty. We can do that with a call to
xfs_trans_ail_tail() instead, where a zero LSN returned indicates and
empty AIL...
SGI-PV: 988143
SGI-Modid: xfs-linux-melb:xfs-kern:32348a
Signed-off-by: David Chinner <david@fromorbit.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
To replace the current generation number ensuring sanity of the AIL
traversal, replace it with an external cursor that is linked to the AIL.
Basically, we store the next item in the cursor whenever we want to drop
the AIL lock to do something to the current item. When we regain the lock.
the current item may already be free, so we can't reference it, but the
next item in the traversal is already held in the cursor.
When we move or delete an object, we search all the active cursors and if
there is an item match we clear the cursor(s) that point to the object.
This forces the traversal to restart transparently.
We don't invalidate the cursor on insert because the cursor still points
to a valid item. If the intem is inserted between the current item and the
cursor it does not matter; the traversal is considered to be past the
insertion point so it will be picked up in the next traversal.
Hence traversal restarts pretty much disappear altogether with this method
of traversal, which should substantially reduce the overhead of pushing on
a busy AIL.
Version 2 o add restart logic o comment cursor interface o minor cleanups
SGI-PV: 988143
SGI-Modid: xfs-linux-melb:xfs-kern:32347a
Signed-off-by: David Chinner <david@fromorbit.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
structures.
Always use the generic xfs_btree_block type instead of the short / long
structures. Add XFS_BTREE_SBLOCK_LEN / XFS_BTREE_LBLOCK_LEN defines for
the length of a short / long form block. The rationale for this is that we
will grow more btree block header variants to support CRCs and other RAS
information, and always accessing them through the same datatype with
unions for the short / long form pointers makes implementing this much
easier.
SGI-PV: 988146
SGI-Modid: xfs-linux-melb:xfs-kern:32300a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: David Chinner <david@fromorbit.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Clean up the way the maximum and minimum records for the btree blocks are
calculated. For the alloc and inobt btrees all the values are
pre-calculated in xfs_mount_common, and we switch the current loop around
the ugly generic macros that use cpp token pasting to generate type names
to two small helpers in normal C code. For the bmbt and bmdr trees these
helpers also exist, but can be called during runtime, too. Here we also
kill various macros dealing with them and inline the logic into the
get_minrecs / get_maxrecs / get_dmaxrecs methods in xfs_bmap_btree.c.
Note that all these new helpers take an xfs_mount * argument which will be
needed to determine the size of a btree block once we add support for
extended btree blocks with CRCs and other RAS information.
SGI-PV: 988146
SGI-Modid: xfs-linux-melb:xfs-kern:32292a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Remove all the useless flags and code keyed off it in xfs_mountfs.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31831a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
kmem_free() function takes (ptr, size) arguments but doesn't actually use
second one.
This patch removes size argument from all callsites.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31050a
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_buf_associate_memory() can fail, but the return is never checked.
Propagate the error through XFS_BUF_SET_PTR() so that failures are
detected.
SGI-PV: 980084
SGI-Modid: xfs-linux-melb:xfs-kern:30831a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Catch errors from xfs_imap() in log recovery when we might be trying to
map an invalid inode number due to a corrupted log.
SGI-PV: 980084
SGI-Modid: xfs-linux-melb:xfs-kern:30829a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfsbdstrat() is declared to return an error. That is never checked because
the error is propagated by the xfs_buf_t that is passed through the
function.
Mark xfsbdstrat() as returning void and comment the prototype on the
methods needed for error checking.
SGI-PV: 980084
SGI-Modid: xfs-linux-melb:xfs-kern:30823a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_free_extent() can fail, but log recovery never bothers to check if it
successfully free the extent it was supposed to. This could lead to silent
corruption during log recovery. Abort log recovery if we fail to free an
extent.
SGI-PV: 980084
SGI-Modid: xfs-linux-melb:xfs-kern:30801a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_trans_commit() can return errors when there are problems in the
transaction subsystem. They are indicative that the entire transaction may
be incomplete, and hence the error should be propagated as there is a good
possibility that there is something fatally wrong in the filesystem. Catch
and propagate or warn about commit errors in the places where they are
currently ignored.
SGI-PV: 980084
SGI-Modid: xfs-linux-melb:xfs-kern:30795a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_trans_reserve() reports errors that should not be ignored. For
example, a shutdown filesystem will report errors through
xfs_trans_reserve() to prevent further changes from being attempted on a
damaged filesystem. Catch and propagate all error conditions from
xfs_trans_reserve().
SGI-PV: 980084
SGI-Modid: xfs-linux-melb:xfs-kern:30794a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Most VN_RELE calls either directly contain a XFS_ITOV or have the
corresponding xfs_inode already in scope. Use the IRELE helper instead of
VN_RELE to clarify the code. With a little more work we can kill VN_RELE
altogether and define IRELE in terms of iput directly.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30710a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
When pdflush is writing back inodes, it can get stuck on inode cluster
buffers that are currently under I/O. This occurs when we write data to
multiple inodes in the same inode cluster at the same time.
Effectively, delayed allocation marks the inode dirty during the data
writeback. Hence if the inode cluster was flushed during the writeback of
the first inode, the writeback of the second inode will block waiting for
the inode cluster write to complete before writing it again for the newly
dirtied inode.
Basically, we want to avoid this from happening so we don't block pdflush
and slow down all of writeback. Hence we introduce a non-blocking async
inode flush flag that pdflush uses. If this flag is set, we use
non-blocking operations (e.g. try locks) whereever we can to avoid
blocking or extra I/O being issued.
SGI-PV: 970925
SGI-Modid: xfs-linux-melb:xfs-kern:30501a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Remove macro-to-small-function indirection from xfs_sb.h, and remove some
which are completely unused.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30528a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
A problem was reported where a system panicked in log recovery due to a
corrupt log record. The cause of the corruption is not known but this
change will at least prevent a crash for this specific scenario. Log
recovery definitely needs some more work in this area.
SGI-PV: 974151
SGI-Modid: xfs-linux-melb:xfs-kern:30318a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Sparse trips over the locking order in xlog_recover_do_efd_trans() when
xfs_trans_delete_ail() drops the ail lock. Because the unlock is
conditional, we need to either annotate with a "fake unlock" or change the
structure of the code so sparse thinks the function always unlocks.
Reordering the code makes it simpler, so do that.
SGI-PV: 972755
SGI-Modid: xfs-linux-melb:xfs-kern:30003a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
These are mostly locking annotations, marking things static, casts where
needed and declaring stuff in header files.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:30002a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Mostly trivial conversion with one exceptions: h_num_logops was kept in
native endian previously and only converted to big endian in xlog_sync,
but we always keep it big endian now. With todays cpus fast byteswap
instructions that's not an issue but the new variant keeps the code clean
and maintainable.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:29821a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
- the various assign lsn macros are replaced by a single inline,
xlog_assign_lsn, which is equivalent to ASSIGN_ANY_LSN_HOST except
for a more sane calling convention. ASSIGN_LSN_DISK is replaced
by xlog_assign_lsn and a manual bytespap, and ASSIGN_LSN by the same,
except we pass the cycle and block arguments explicitly instead of a
log paramter. The latter two variants only had 2, respectively one
user anyway.
- the GET_CYCLE is replaced by a xlog_get_cycle inline with exactly the
same calling conventions.
- GET_CLIENT_ID is replaced by xlog_get_client_id which leaves away
the unused arch argument. Instead of conditional defintions
depending on host endianess we now do an unconditional swap and shift
then, which generates equal code.
- the unused XLOG_SET macro is removed.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:29820a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
- the various assign lsn macros are replaced by a single inline,
xlog_assign_lsn, which is equivalent to ASSIGN_ANY_LSN_HOST except
for a more sane calling convention. ASSIGN_LSN_DISK is replaced
by xlog_assign_lsn and a manual bytespap, and ASSIGN_LSN by the same,
except we pass the cycle and block arguments explicitly instead of a
log paramter. The latter two variants only had 2, respectively one
user anyway.
- the GET_CYCLE is replaced by a xlog_get_cycle inline with exactly the
same calling conventions.
- GET_CLIENT_ID is replaced by xlog_get_client_id which leaves away
the unused arch argument. Instead of conditional defintions
depending on host endianess we now do an unconditional swap and shift
then, which generates equal code.
- the unused XLOG_SET macro is removed.
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:29819a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Creates a new xfs_dsb_t that is __be annotated and keeps xfs_sb_t for the
incore one. xfs_xlatesb is renamed to xfs_sb_to_disk and only handles the
incore -> disk conversion. A new helper xfs_sb_from_disk handles the other
direction and doesn't need the slightly hacky table-driven approach
because we only ever read the full sb from disk.
The handling of shared r/o filesystems has been buggy on little endian
system and fixing this required shuffling around of some code in that
area.
SGI-PV: 968563
SGI-Modid: xfs-linux-melb:xfs-kern:29477a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Biggest bit is duplicating the dinode structure so we have one annotated for
native endianess and one for disk endianess. The other significant change
is that xfs_xlate_dinode_core is split into one helper per direction to
allow for proper annotations, everything else is trivial.
As a sidenode splitting out the incore dinode means we can move it into
xfs_inode.h in a later patch and severely improving on the include hell in
xfs.
SGI-PV: 968563
SGI-Modid: xfs-linux-melb:xfs-kern:29476a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
The new xlog_recover_do_reg_buffer checks call be16_to_cpu on di_gen which
is a 32bit value so sparse rightly complains. Fortunately the warning is
harmless because we don't care for the value, but only whether it's
non-NULL. Due to that fact we can simply kill the endian swaps on this and
the previous di_mode check entirely.
SGI-PV: 969656
SGI-Modid: xfs-linux-melb:xfs-kern:29709a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Sparse now warns about comparing pointers to 0, so change all instance
where that happens to NULL instead.
SGI-PV: 968555
SGI-Modid: xfs-linux-melb:xfs-kern:29308a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
When we have a couple of hundred transactions on the fly at once, they all
typically modify the on disk superblock in some way.
create/unclink/mkdir/rmdir modify inode counts, allocation/freeing modify
free block counts.
When these counts are modified in a transaction, they must eventually lock
the superblock buffer and apply the mods. The buffer then remains locked
until the transaction is committed into the incore log buffer. The result
of this is that with enough transactions on the fly the incore superblock
buffer becomes a bottleneck.
The result of contention on the incore superblock buffer is that
transaction rates fall - the more pressure that is put on the superblock
buffer, the slower things go.
The key to removing the contention is to not require the superblock fields
in question to be locked. We do that by not marking the superblock dirty
in the transaction. IOWs, we modify the incore superblock but do not
modify the cached superblock buffer. In short, we do not log superblock
modifications to critical fields in the superblock on every transaction.
In fact we only do it just before we write the superblock to disk every
sync period or just before unmount.
This creates an interesting problem - if we don't log or write out the
fields in every transaction, then how do the values get recovered after a
crash? the answer is simple - we keep enough duplicate, logged information
in other structures that we can reconstruct the correct count after log
recovery has been performed.
It is the AGF and AGI structures that contain the duplicate information;
after recovery, we walk every AGI and AGF and sum their individual
counters to get the correct value, and we do a transaction into the log to
correct them. An optimisation of this is that if we have a clean unmount
record, we know the value in the superblock is correct, so we can avoid
the summation walk under normal conditions and so mount/recovery times do
not change under normal operation.
One wrinkle that was discovered during development was that the blocks
used in the freespace btrees are never accounted for in the AGF counters.
This was once a valid optimisation to make; when the filesystem is full,
the free space btrees are empty and consume no space. Hence when it
matters, the "accounting" is correct. But that means the when we do the
AGF summations, we would not have a correct count and xfs_check would
complain. Hence a new counter was added to track the number of blocks used
by the free space btrees. This is an *on-disk format change*.
As a result of this, lazy superblock counters are a mkfs option and at the
moment on linux there is no way to convert an old filesystem. This is
possible - xfs_db can be used to twiddle the right bits and then
xfs_repair will do the format conversion for you. Similarly, you can
convert backwards as well. At some point we'll add functionality to
xfs_admin to do the bit twiddling easily....
SGI-PV: 964999
SGI-Modid: xfs-linux-melb:xfs-kern:28652a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tim Shimmin <tes@sgi.com>
After filesystem recovery the superblock is re-read to bring in any
changes. If the per-cpu superblock counters are not re-initialized from
the superblock then the next time the per-cpu counters are disabled they
might overwrite the global counter with a bogus value.
SGI-PV: 957348
SGI-Modid: xfs-linux-melb:xfs-kern:27999a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
logged version of di_next_unlinked which is actually always stored in the
correct ondisk format. This was pointed out to us by Shailendra Tripathi.
And is evident in the xfs qa test of 121.
SGI-PV: 953263
SGI-Modid: xfs-linux-melb:xfs-kern:26044a
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
64bit kernels allow recovery to handle both versions and do the necessary
decoding
SGI-PV: 952214
SGI-Modid: xfs-linux-melb:xfs-kern:26011a
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Dave Chinner
Lucas De Marchi
Christoph Hellwig
Alex Elder
Dave Chinner
Eric Sandeen
Linus Torvalds
Joe Perches
Andy Poling
Jan Rekorajski
Christoph Hellwig
Denys Vlasenko
David Chinner
Harvey Harrison
Lachlan McIlroy
Donald Douwsma
Tim Shimmin
Utako Kusaka
Nathan Scott
Tim Shimmin
Eric Sandeen
Christoph Hellwig
Linus Torvalds