Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.7. Here's the summary of
the changes:
- ATH79: Support for DTB passuing using the UHI boot protocol
- ATH79: Remove support for builtin DTB.
- ATH79: Add zboot debug serial support.
- ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
and DPT-Module.
- ATH79: Update devicetree clock support for AR9132 and AR9331.
- ATH79: Cleanup the DT code.
- ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
- ATH79: Fix regression in PCI window initialization.
- BCM47xx: Move SPROM driver to drivers/firmware/
- BCM63xx: Enable partition parser in defconfig.
- BMIPS: BMIPS5000 has I cache filing from D cache
- BMIPS: BMIPS: Add cpu-feature-overrides.h
- BMIPS: Add Whirlwind support
- BMIPS: Adjust mips-hpt-frequency for BCM7435
- BMIPS: Remove maxcpus from BCM97435SVMB DTS
- BMIPS: Add missing 7038 L1 register cells to BCM7435
- BMIPS: Various tweaks to initialization code.
- BMIPS: Enable partition parser in defconfig.
- BMIPS: Cache tweaks.
- BMIPS: Add UART, I2C and SATA devices to DT.
- BMIPS: Add BCM6358 and BCM63268support
- BMIPS: Add device tree example for BCM6358.
- BMIPS: Improve Improve BCM6328 and BCM6368 device trees
- Lantiq: Add support for device tree file from boot loader
- Lantiq: Allow build with no built-in DT.
- Loongson 3: Reserve 32MB for RS780E integrated GPU.
- Loongson 3: Fix build error after ld-version.sh modification
- Loongson 3: Move chipset ACPI code from drivers to arch.
- Loongson 3: Speedup irq processing.
- Loongson 3: Add basic Loongson 3A support.
- Loongson 3: Set cache flush handlers to nop.
- Loongson 3: Invalidate special TLBs when needed.
- Loongson 3: Fast TLB refill handler.
- MT7620: Fallback strategy for invalid syscfg0.
- Netlogic: Fix CP0_EBASE redefinition warnings
- Octeon: Initialization fixes
- Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
- Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
- Octeon: Correctly handle endian-swapped initramfs images.
- Octeon: Support CN73xx, CN75xx and CN78xx.
- Octeon: Remove dead code from cvmx-sysinfo.
- Octeon: Extend number of supported CPUs past 32.
- Octeon: Remove some code limiting NR_IRQS to 255.
- Octeon: Simplify octeon_irq_ciu_gpio_set_type.
- Octeon: Mark some functions __init in smp.c
- Octeon: Octeon: Add Octeon III CN7xxx interface detection
- PIC32: Add serial driver and bindings for it.
- PIC32: Add PIC32 deadman timer driver and bindings.
- PIC32: Add PIC32 clock timer driver and bindings.
- Pistachio: Determine SoC revision during boot
- Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
- Sibyte: Strip redundant comments from bcm1480_regs.h.
- Panic immediately if panic_on_oops is set.
- module: fix incorrect IS_ERR_VALUE macro usage.
- module: Make consistent use of pr_*
- Remove no longer needed work_on_cpu() call.
- Remove CONFIG_IPV6_PRIVACY from defconfigs.
- Fix registers of non-crashing CPUs in dumps.
- Handle MIPSisms in new vmcore_elf32_check_arch.
- Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
- Allow RIXI to be used on non-R2 or R6 cores.
- Reserve nosave data for hibernation
- Fix siginfo.h to use strict POSIX types.
- Don't unwind user mode with EVA.
- Fix watchpoint restoration
- Ptrace watchpoints for R6.
- Sync icache when it fills from dcache
- I6400 I-cache fills from dcache.
- Various MSA fixes.
- Cleanup MIPS_CPU_* definitions.
- Signal: Move generic copy_siginfo to signal.h
- Signal: Fix uapi include in exported asm/siginfo.h
- Timer fixes for sake of KVM.
- XPA TLB refill fixes.
- Treat perf counter feature
- Update John Crispin's email address
- Add PIC32 watchdog and bindings.
- Handle R10000 LL/SC bug in set_pte()
- cpufreq: Various fixes for Longson1.
- R6: Fix R2 emulation.
- mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
- ELF: ABI and FP fixes.
- Allow for relocatable kernel and use that to support KASLR.
- Fix CPC_BASE_ADDR mask
- Plenty fo smp-cps, CM, R6 and M6250 fixes.
- Make reset_control_ops const.
- Fix kernel command line handling of leading whitespace.
- Cleanups to cache handling.
- Add brcm, bcm6345-l1-intc device tree bindings.
- Use generic clkdev.h header
- Remove CLK_IS_ROOT usage.
- Misc small cleanups.
- CM: Fix compilation error when !MIPS_CM
- oprofile: Fix a preemption issue
- Detect DSP ASE v3 support:1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
MIPS: pic32mzda: fix getting timer clock rate.
MIPS: ath79: fix regression in PCI window initialization
MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
MIPS: Fix VZ probe gas errors with binutils <2.24
MIPS: perf: Fix I6400 event numbers
MIPS: DEC: Export `ioasic_ssr_lock' to modules
MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
MIPS: CM: Fix compilation error when !MIPS_CM
MIPS: Fix genvdso error on rebuild
USB: ohci-jz4740: Remove obsolete driver
MIPS: JZ4740: Probe OHCI platform device via DT
MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
MIPS: pistachio: Determine SoC revision during boot
MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
MIPS: Prevent "restoration" of MSA context in non-MSA kernels
MIPS: cevt-r4k: Dynamically calculate min_delta_ns
MIPS: malta-time: Take seconds into account
MIPS: malta-time: Start GIC count before syncing to RTC
MIPS: Force CPUs to lose FP context during mode switches
...
Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons. For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to
get done.
Finally, reset controller handling as always gets merged through here
as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=x+iD
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons.
For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to get
done.
Finally, reset controller handling as always gets merged through here
as well"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
arm-ccn: Enable building as module
soc/tegra: pmc: Add generic PM domain support
usb: xhci: tegra: Add Tegra210 support
usb: xhci: Add NVIDIA Tegra XUSB controller driver
dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
PCI: tegra: Support per-lane PHYs
dt-bindings: pci: tegra: Update for per-lane PHYs
phy: tegra: Add Tegra210 support
phy: Add Tegra XUSB pad controller support
dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
phy: core: Allow children node to be overridden
clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
drivers: firmware: psci: make two helper functions inline
soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
...
Since commit 3b9d6da67e ("cpu/hotplug: Fix rollback during error-out
in __cpu_disable()") it is ensured that callbacks of CPU_ONLINE and
CPU_DOWN_PREPARE are processed on the hotplugged CPU. Due to this
work_on_cpu() calls are no longer required.
Replace work_on_cpu() with a direct call of mips_cdmm_bus_up() or
mips_cdmm_bus_down(). Description of those functions are adapted.
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: rt@linutronix.de
Patchwork: https://patchwork.linux-mips.org/patch/13197/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS kernels allow platforms to invoke a custom Bus Error handler, add the
necessary code to do this for Broadcom SoCs where the GISB bus error handler can be used.
We may get a bus error from an address decoded outside of the GISB bus space,
so we need to check the validity of such a capture before printing anything.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: cernekee@gmail.com
Cc: arnd@arndb.de
Cc: jaedon.shin@gmail.com
Cc: pgynther@google.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12284/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arm-ccn driver uses irq_set_affinity, which is not exported and
hence cannot be built as a module, eventhough we have all the
bits ready. This patch makes use of the exported helper
irq_set_affinity_hint() instead. Also, the __free_irq expects
the affinity_hint to be NULL when we free the irq. So set the
affinity_hint to NULL at clean up.
Now that we can build it as a module, update the Kconfig to
reflect the change.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Justin adds a soc_dev driver to properly report to user-space the Broadcom
STB SoC family, product and revision
- Florian reworks how the brcmstb_gisb driver dependency is done to enable it
on Broadcom STB MIPS-based SoCs and remove a select in
arch/arm/mach-bcm/Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OJuu
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.7/drivers' of http://github.com/Broadcom/stblinux into next/drivers
Merge "Broadcom ARM-based SoCs drivers changes" from Florian Fainelli:
- Justin adds a soc_dev driver to properly report to user-space the Broadcom
STB SoC family, product and revision
- Florian reworks how the brcmstb_gisb driver dependency is done to enable it
on Broadcom STB MIPS-based SoCs and remove a select in
arch/arm/mach-bcm/Kconfig
* tag 'arm-soc/for-4.7/drivers' of http://github.com/Broadcom/stblinux:
bus: brcmstb_gisb: Rework dependencies
soc: brcmstb: add SoC driver to brcmstb
Do not have the machine Kconfig entry point need to select
BRCMSTB_GISB_ARB, instead, just let it be default ARCH_BRCMSTB which is
a better way to deal with this. While at it, also make it default
BMIPS_GENERIC so the legacy MIPS-based STB platforms can benefit from
the same thing.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
- fix USB adress register for Linksys Armada 388 based boards
- fix build warning in mvebu-mbus
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlcGmgAACgkQCwYYjhRyO9WmLACgkLHkRxw3Xmp5/g3tSgBzh06A
Qb4An2adegesOnsQzbVwWeaCaJxdEbk/
=sMxU
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.6-1' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 4.6 (part 1)
- fix USB adress register for Linksys Armada 388 based boards
- fix build warning in mvebu-mbus
* tag 'mvebu-fixes-4.6-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Correct unit address for linksys
bus: mvebu-mbus: use %pa to print phys_addr_t
Signed-off-by: Olof Johansson <olof@lixom.net>
A recent change to the mbus driver added a warning printk that
prints a phys_addr_t using the %x format string, which fails in
case we build with 64-bit phys_addr_t:
drivers/bus/mvebu-mbus.c: In function 'mvebu_mbus_get_dram_win_info':
drivers/bus/mvebu-mbus.c:975:9: error: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'phys_addr_t {aka long long unsigned int}' [-Werror=format=]
This uses the special %pa format string instead, so we always
print the correct type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f2900acea8 ("bus: mvebu-mbus: provide api for obtaining IO and DRAM window information")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- Initial support for ARMv8.1 CPU PMUs
- Support for the CPU PMU in Cavium ThunderX
- CPU PMU support for systems running 32-bit Linux in secure mode
- Support for the system PMU in ARM CCI-550 (Cache Coherent Interconnect)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJW794rAAoJELescNyEwWM0O5IH/0ejoUjip3n4dFZnSzAbQQZe
VxCy3DXW5gS8YaswwX2dFw9K772/BpHlazq8AIJIhaR+b+Zzl5t0iOc12HluDilV
pMvi0JTCxwJhsEiKZnP0cVAU9HM6MAgtMOEegkd/YNESKQey30NeDtIcz/pQfTUV
28AF71+w5VPj/1EpHEEhHQsASRIx7eDbKzThzdlb8PnDS0o23QJhL9HjVTNIAlB8
BGxrUBKtBu0eH2Hx33vNjc7UYx1WZQlCk5cAaXevA8mbFXzYaMQI2Cel2nbNMO9i
eu5zPkDUCG7dq16PxK6IgM4AsDCtmmDuckLdN6UEQWYxkLbb2qHNRKtj0bKB8Sk=
=E4PE
-----END PGP SIGNATURE-----
Merge tag 'arm64-perf' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm[64] perf updates from Will Deacon:
"I have another mixed bag of ARM-related perf patches here.
It's about 25% CPU and 75% interconnect, but with drivers/bus/
languishing without an obvious maintainer or tree, Olof and I agreed
to keep all of these PMU patches together. I suspect a whole load of
code from drivers/bus/arm-* can be moved under drivers/perf/, so
that's on the radar for the future.
Summary:
- Initial support for ARMv8.1 CPU PMUs
- Support for the CPU PMU in Cavium ThunderX
- CPU PMU support for systems running 32-bit Linux in secure mode
- Support for the system PMU in ARM CCI-550 (Cache Coherent Interconnect)"
* tag 'arm64-perf' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (26 commits)
drivers/perf: arm_pmu: avoid NULL dereference when not using devicetree
arm64: perf: Extend ARMV8_EVTYPE_MASK to include PMCR.LC
arm-cci: remove unused variable
arm-cci: don't return value from void function
arm-cci: make private functions static
arm-cci: CoreLink CCI-550 PMU driver
arm-cci500: Rearrange PMU driver for code sharing with CCI-550 PMU
arm-cci: CCI-500: Work around PMU counter writes
arm-cci: Provide hook for writing to PMU counters
arm-cci: Add helper to enable PMU without synchornising counters
arm-cci: Add routines to save/restore all counters
arm-cci: Get the status of a counter
arm-cci: write_counter: Remove redundant check
arm-cci: Delay PMU counter writes to pmu::pmu_enable
arm-cci: Refactor CCI PMU enable/disable methods
arm-cci: Group writes to counter
arm-cci: fix handling cpumask_any_but return value
arm-cci: simplify sysfs attr handling
drivers/perf: arm_pmu: implement CPU_PM notifier
arm64: dts: Add Cavium ThunderX specific PMU
...
Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons:
- Rockchip rk3368 gains power domain support
- Small updates for the ARM spmi driver
- The Atmel PMC driver saw a larger rework, touching both
arch/arm/mach-at91 and drivers/clk/at91
- All reset controller driver changes alway get merged through
arm-soc, though this time the largest change is the addition
of a MIPS pistachio reset driver
- One bugfix for the NXP (formerly Freescale) i.MX weim bus driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HS4G
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons:
- Rockchip rk3368 gains power domain support
- Small updates for the ARM spmi driver
- The Atmel PMC driver saw a larger rework, touching both
arch/arm/mach-at91 and drivers/clk/at91
- All reset controller driver changes alway get merged through
arm-soc, though this time the largest change is the addition of a
MIPS pistachio reset driver
- One bugfix for the NXP (formerly Freescale) i.MX weim bus driver"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
bus: imx-weim: Take the 'status' property value into account
clk: at91: remove useless includes
clk: at91: pmc: remove useless capacities handling
clk: at91: pmc: drop at91_pmc_base
usb: gadget: atmel: access the PMC using regmap
ARM: at91: remove useless includes and function prototypes
ARM: at91: pm: move idle functions to pm.c
ARM: at91: pm: find and remap the pmc
ARM: at91: pm: simply call at91_pm_init
clk: at91: pmc: move pmc structures to C file
clk: at91: pmc: merge at91_pmc_init in atmel_pmc_probe
clk: at91: remove IRQ handling and use polling
clk: at91: make use of syscon/regmap internally
clk: at91: make use of syscon to share PMC registers in several drivers
hwmon: (scpi) add energy meter support
firmware: arm_scpi: add support for 64-bit sensor values
firmware: arm_scpi: decrease Tx timeout to 20ms
firmware: arm_scpi: fix send_message and sensor_get_value for big-endian
reset: sti: Make reset_control_ops const
reset: zynq: Make reset_control_ops const
...
This commit enables finding appropriate mbus window and obtaining its
target id and attribute for given physical address in two separate
routines, both for IO and DRAM windows. This functionality
is needed for Armada XP/38x Network Controller's Buffer Manager and
PnC configuration.
[gregory.clement@free-electrons.com: Fix size test for
mvebu_mbus_get_dram_win_info]
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
[DRAM window information reference in LKv3.10]
Signed-off-by: Evan Wang <xswang@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we have an incorrect behaviour when multiple devices
are present under the weim node. For example:
&weim {
...
status = "okay";
sram@0,0 {
...
status = "okay";
};
mram@0,0 {
...
status = "disabled";
};
};
In this case only the 'sram' device should be probed and not 'mram'.
However what happens currently is that the status variable is ignored,
causing the 'sram' device to be disabled and 'mram' to be enabled.
Change the weim_parse_dt() function to use
for_each_available_child_of_node()so that the devices marked with
'status = disabled' are not probed.
Cc: <stable@vger.kernel.org>
Suggested-by: Wolfgang Netbal <wolfgang.netbal@sigmatek.at>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Some minor fixes for the RSB and SRAM controller drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5Ffk
-----END PGP SIGNATURE-----
Merge tag 'sunxi-drivers-for-4.6' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/drivers
Merge "Allwinner drivers changes for 4.6" from Maxime Ripard:
Some minor fixes for the RSB and SRAM controller drivers
* tag 'sunxi-drivers-for-4.6' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
drivers: soc: sunxi: Fix mask generation for SRAM mapping
drivers: sunxi-rsb: fix error output type
cci_pmu_sync_counters and pmu_event_set_period are internal functions
to the CCI PMU driver, so make them static to avoid polluting the kernel
namespace.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add ARM CoreLink CCI-550 cache coherent interconnect PMU
driver support. The CCI-550 PMU shares all the attributes of CCI-500
PMU, except for an additional master interface (MI-6 - 0xe).
CCI-550 requires the same work around as for CCI-500 to
write to the PMU counter.
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
CCI-550 PMU shares most of the CCI-500 PMU attributes including the
event format, PMU event codes. The only difference is an additional
master interface (MI6 - 0xe). Hence we share the driver code for both,
except for a model specific event validate method.
This patch renames the common CCI500 symbols to CCI5xx, including the
Kconfig symbol.
No functional changes to the PMU driver.
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The CCI PMU driver sets the event counter to the half of the maximum
value(2^31) it can count before we start the counters via
pmu_event_set_period(). This is done to give us the best chance to
handle the overflow interrupt, taking care of extreme interrupt latencies.
However, CCI-500 comes with advanced power saving schemes, which
disables the clock to the event counters unless the counters are enabled to
count (PMCR.CEN). This prevents the driver from writing the period to the
counters before starting them. Also, there is no way we can reset the
individual event counter to 0 (PMCR.RST resets all the counters, losing
their current readings). However the value of the counter is preserved and
could be read back, when the counters are not enabled.
So we cannot reliably use the counters and compute the number of events
generated during the sampling period since we don't have the value of the
counter at start.
This patch works around this issue by changing writes to the counter
with the following steps.
1) Disable all the counters (remembering any counters which were enabled)
2) Enable the PMU, now that all the counters are disabled.
For each counter to be programmed, repeat steps 3-7
3) Save the current event and program the target counter to count an
invalid event, which by spec is guaranteed to not-generate any events.
4) Enable the target counter.
5) Write to the target counter.
6) Disable the target counter
7) Restore the event back on the target counter.
8) Disable the PMU
9) Restore the status of the all the counters
Cc: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add a hook for writing to CCI PMU counters. This callback
can be used for CCI models which requires some extra work
to program the PMU counter values. To accommodate group writes
and single counter writes, the call back accepts a bitmask
of the counter indices which need to be programmed with the
given value.
Cc: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
On CCI-500 writing to a counter requires turning the PMU on. So,
synchronising the counter state should not be performed for such special cases,
while turning the PMU on. This patch adds a helper, __cci_pmu_enable_nosync(),
without flushing the counter states.
Cc: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Adds helper routines to disable the counter controls for
all the counters on the CCI PMU and restore it back, by
preserving the original state in caller provided mask.
Cc: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add helper routines to check if the counter is enabled or not.
Cc: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
pmu_write_counter() is now only called from pmu_write_counters(),
which does so for each set index in the given mask, bounded by
cci_pmu->num_cntrs. So, there is no need for an extra check to
make sure the given counter is valid inside pmu_write_counter.
This patch gets rid of that.
Cc: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
CCI PMU driver always reprograms the counters to a safe value (half of the
counter max, = 2^31) before starting the profiling to account for extreme
interrupt latencies. Also, the cost of writing to a PMU counter could be
very costly on some PMUs(e.g, CCI-500). In order to ammortise the cost of
programming the counters, this patch delays the counter writes to pmu::pmu_enable().
We use the PER_HES_ARCH flag to keep track of the counters which need to
be programmed. Before turning on the PMU, we go through the counters that
were marked for write, and perform the operation in a batch.
To unify all the counter writes to pmu_enable(), this patch also makes sure that
we disable-and-enable the PMU in the irq handler to program any counters that
overflowed.
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch refactors the CCI PMU driver code a little bit to
make it easier share the code for enabling/disabling the CCI
PMU. This will be used by the hooks to work around the special cases
where writing to a counter is not always that easy(e.g, CCI-500)
No functional changes.
Cc: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add a helper to group the writes to PMU counter, this will be
used to delay setting the event period to pmu::pmu_enable()
Cc: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
cpumask_any_but returns value >= nr_cpu_ids if there are no more CPUs.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There's no need to dynamically initialise attribute pointers when we can
get the compiler to do it for us. We also don't need a dev_ext_attribute
for the cpumask, as the drvdata for a PMU device is a pointer to struct
pmu.
Cc: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
At first, commit 4b7f48d395 ("bus: uniphier-system-bus: add UniPhier
System Bus driver") introduced this driver as a tristate one.
Then, commit 326ea45aa8 ("bus: uniphier: allow only built-in
driver") temporarily made it boolean in order to fix a link error
in case it is compiled as a module.
The root cause was fixed by commit b80443c221 ("of/platform: export
of_default_bus_match_table").
Now this driver can really be a module.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
for_each_compatible_node performs an of_node_get on each iteration, so
to break out of the loop an of_node_put is required.
Found using Coccinelle. The semantic patch used for this is as follows:
// <smpl>
@@
expression e;
local idexpression n;
@@
for_each_compatible_node(n, ...) {
... when != of_node_put(n)
when != e = n
(
return n;
+ of_node_put(n);
? return ...;
)
...
}
// </smpl>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
"len" is actually a size_t in this function here, so properly annotate
the dev_err printf type to allow compilation for 64-bit architectures.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Driver updates for ARM SoCs. Some for SoC-family code under drivers/soc,
but also some other driver updates that don't belong anywhere else. We also
bring in the drivers/reset code through arm-soc.
Some of the larger updates:
- Qualcomm support for SMEM, SMSM, SMP2P. All used to communicate with other
parts of the chip/board on these platforms, all proprietary protocols that
don't fit into other subsystems and live in drivers/soc for now.
- System bus driver for UniPhier
- Driver for the TI Wakeup M3 IPC device
- Power management for Raspberry PI
+ Again a bunch of other smaller updates and patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=khZ5
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs. Some for SoC-family code under
drivers/soc, but also some other driver updates that don't belong
anywhere else. We also bring in the drivers/reset code through
arm-soc.
Some of the larger updates:
- Qualcomm support for SMEM, SMSM, SMP2P. All used to communicate
with other parts of the chip/board on these platforms, all
proprietary protocols that don't fit into other subsystems and live
in drivers/soc for now.
- System bus driver for UniPhier
- Driver for the TI Wakeup M3 IPC device
- Power management for Raspberry PI
+ Again a bunch of other smaller updates and patches"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: uniphier: allow only built-in driver
ARM: bcm2835: clarify RASPBERRYPI_FIRMWARE dependency
MAINTAINERS: Drop Kumar Gala from QCOM
bus: uniphier-system-bus: add UniPhier System Bus driver
ARM: bcm2835: add rpi power domain driver
dt-bindings: add rpi power domain driver bindings
ARM: bcm2835: Define two new packets from the latest firmware.
drivers/soc: make mediatek/mtk-scpsys.c explicitly non-modular
soc: mediatek: SCPSYS: Add regulator support
MAINTAINERS: Change QCOM entries
soc: qcom: smd-rpm: Add existing platform support
memory/tegra: Add number of TLB lines for Tegra124
reset: hi6220: fix modular build
soc: qcom: Introduce WCNSS_CTRL SMD client
ARM: qcom: select ARM_CPU_SUSPEND for power management
MAINTAINERS: Add rules for Qualcomm dts files
soc: qcom: enable smsm/smp2p modular build
serial: msm_serial: Make config tristate
soc: qcom: smp2p: Qualcomm Shared Memory Point to Point
soc: qcom: smsm: Add driver for Qualcomm SMSM
...
Building the newly added uniphier system bus driver as a module
causes a link error, so let's only allow it to be built-in for
now, to fix allmodconfig:
ERROR: "of_default_bus_match_table" [drivers/bus/uniphier-system-bus.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
0x4e is the runtime address normally associated with perihperal ICs.
0x45 is not a valid runtime address.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The primary PMICs use 0x3a3 as their hardware address, not 0x3e3.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The UniPhier System Bus is an external bus that connects on-board
devices to the UniPhier SoC. Each bank (chip select) is dynamically
mapped to the CPU-viewed address base via the bus controller. The
bus controller must be configured before any access to the bus.
This driver parses the "ranges" property of the System Bus node and
initialized the bus controller. After the bus becomes ready, devices
below it are populated.
Note:
Each bank can be mapped anywhere in the supported address space;
there is nothing preventing us from assigning bank 0 on 0x42000000,
0x43000000, or anywhere as long as such region is not used by others.
So, the "ranges" is just one possible software configuration, which
does not seem to fit in device tree because device tree is a hardware
description language. However, of_translate_address() requires
"ranges" in every bus node between CPUs and device mapped on the CPU
address space. In other words, "ranges" properties must be statically
defined in device tree. After some discussion, I decided the dynamic
address reassignment by the driver is too bothersome. Instead, the
device tree should provide a reasonable translation setup that the OS
can rely on.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Two patches, one to fix the touchscreen axis on one Allwinner board, and
the other one fixing a mutex unlocking issue on one error path in the RSB
driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9lSI
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner fixes for 4.4" from Maxime Ripard:
Allwinner fixes for 4.4
Two patches, one to fix the touchscreen axis on one Allwinner board, and
the other one fixing a mutex unlocking issue on one error path in the RSB
driver.
* tag 'sunxi-fixes-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
bus: sunxi-rsb: unlock on error in sunxi_rsb_read()
ARM: dts: sunxi: sun6i-a31s-primo81.dts: add touchscreen axis swapping property
Don't forget to unlock before returning an error code.
Fixes: d787dcdb9c ('bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As we've enabled multiplatform kernels on ARM, and greatly done away with
the contents under arch/arm/mach-*, there's still need for SoC-related
drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate
with power management blocks on these SoCs for use by clock, regulator and
bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be confused with
PSCI (Power State Coordination Interface). SCPI is used to communicate with
the assistant embedded cores doing power management, and we have yet to see
how many of them will implement this for their hardware vs abstracting in
other ways (or not at all like in the past).
- To make confusion between SCPI and PSCI more likely, this release also
includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dm+I
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
Reduced Serial Bus (RSB) is an Allwinner proprietery interface
used to communicate with PMICs and other peripheral ICs.
RSB is a two-wire push-pull serial bus that supports 1 master
device and up to 15 active slave devices.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
When PMU context is migrating between CPUs, interrupt affinity is set as
well. Only this should not happen when the CCN interrupt is not being
used at all (the driver is using a hrtimer tick instead).
Fixed now.
Cc: <stable@vger.kernel.org> # 4.2+
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When migrating events the driver picks another cpu using
cpumask_any_but() function, which returns value >= nr_cpu_ids
when there is none available, not a negative value as the code
assumed. Fixed now.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove extra space between platform prefix and driver name in MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Disable building CCI-500 PMU driver by default.
Reported-by: Russell King <linux@arm.linux.org.uk>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: arm@kernel.org
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds
Anna-Maria Gleixner
Florian Fainelli
Suzuki K Poulose
Arnd Bergmann
Olof Johansson
Kunihiko Hayashi
Simon Horman
Marcin Wojtas
Fabio Estevam
Will Deacon
Andrzej Hajda
Mark Rutland
Masahiro Yamada
Amitoj Kaur Chawla
Andre Przywara
Chen-Yu Tsai
Kevin Hilman
Dan Carpenter
Tony Lindgren
Pawel Moll
Axel Lin