Move block I/O operations to a separate file. It is because it will
be used later not only by the swap writer.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Remove support of reads with offset. This means snapshot_read/write_next
now does not accept count parameter. It allows to clean up the functions
and snapshot handle which no longer needs to care about offsets.
/dev/snapshot handler is converted to simple_{read_from,write_to}_buffer
which take care of offsets.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
When CONFIG_DEBUG_BLOCK_EXT_DEVT is set we decode the device
improperly by old_decode_dev and it results in an error while
hibernating with s2disk.
All users already pass the new device number, so switch to
new_decode_dev().
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-and-tested-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
When the cgroup freezer is used to freeze tasks we do not want to thaw
those tasks during resume. Currently we test the cgroup freezer
state of the resuming tasks to see if the cgroup is FROZEN. If so
then we don't thaw the task. However, the FREEZING state also indicates
that the task should remain frozen.
This also avoids a problem pointed out by Oren Ladaan: the freezer state
transition from FREEZING to FROZEN is updated lazily when userspace reads
or writes the freezer.state file in the cgroup filesystem. This means that
resume will thaw tasks in cgroups which should be in the FROZEN state if
there is no read/write of the freezer.state file to trigger this
transition before suspend.
NOTE: Another "simple" solution would be to always update the cgroup
freezer state during resume. However it's a bad choice for several reasons:
Updating the cgroup freezer state is somewhat expensive because it requires
walking all the tasks in the cgroup and checking if they are each frozen.
Worse, this could easily make resume run in N^2 time where N is the number
of tasks in the cgroup. Finally, updating the freezer state from this code
path requires trickier locking because of the way locks must be ordered.
Instead of updating the freezer state we rely on the fact that lazy
updates only manage the transition from FREEZING to FROZEN. We know that
a cgroup with the FREEZING state may actually be FROZEN so test for that
state too. This makes sense in the resume path even for partially-frozen
cgroups -- those that really are FREEZING but not FROZEN.
Reported-by: Oren Ladaan <orenl@cs.columbia.edu>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Cc: stable@kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
show_state will dump all tasks state, so if freezer failed to freeze
any task, kernel will dump all tasks state and flood the dmesg log.
This patch makes freezer only show state of tasks refusing to freeze.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
There are quite a few GFP_KERNEL memory allocations made during
suspend/hibernation and resume that may cause the system to hang, because
the I/O operations they depend on cannot be completed due to the
underlying devices being suspended.
Avoid this problem by clearing the __GFP_IO and __GFP_FS bits in
gfp_allowed_mask before suspend/hibernation and restoring the original
values of these bits in gfp_allowed_mask durig the subsequent resume.
[akpm@linux-foundation.org: fix CONFIG_PM=n linkage]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The hibernate memory preallocation code allocates memory to push some
user space data out of physical RAM, so that the hibernation image is
not too large. It allocates more memory than necessary for creating
the image, so it has to release some pages to make room for
allocations made while suspending devices and disabling nonboot CPUs,
or the system will hang due to the lack of free pages to allocate
from. Unfortunately, the function used for freeing these pages,
free_unnecessary_pages(), contains a bug that prevents it from doing
the job on all systems without highmem.
Fix this problem, which is a regression from the 2.6.30 kernel, by
using the right condition for the termination of the loop in
free_unnecessary_pages().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Alan Jenkins <sourcejedi.lkml@googlemail.com>
Cc: stable@kernel.org
Its contents and entry in Makefile were already removed in
8e60c6a134
(Shift remaining code from swsusp.c to hibernate.c)
but somehow it remained in-place (rjw: which most likely was my
mistake).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Remove a trailing space from a message in swsusp_save().
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
It will never reach here if the sws_resume_bdev is erratic.
swsusp_read() is called only from software_resume(), but after
swsusp_check() which would catch the error state.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
They were deprecated and removed from exported headers more than 2
years ago. Inform users about their removal in the future now.
(Switch cases needed to be reorderded for an easy fall through.)
And add an entry to feature-removal-schedule.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add configuration switch CONFIG_PM_ADVANCED_DEBUG for compiling in
extra PM debugging/testing code allowing one to access some
PM-related attributes of devices from the user space via sysfs.
If CONFIG_PM_ADVANCED_DEBUG is set, add sysfs attribute power/async
for every device allowing the user space to access the device's
power.async_suspend flag and modify it, if desired.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add sysfs attribute /sys/power/pm_async allowing the user space to
disable/enable asynchronous suspend/resume of devices.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Introduce run-time PM callbacks for the PCI bus type. Make the new
callbacks work in analogy with the existing system sleep PM
callbacks, so that the drivers already converted to struct dev_pm_ops
can use their suspend and resume routines for run-time PM without
modifications.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The kernel offers with TIOCL_GETKMSGREDIRECT ioctl() the possibility to
redirect the kernel messages to a specific console.
However, since it's not possible to switch to the kernel message console
after a panic(), it would be nice if the kernel would print the panic
message on the current console.
This patch series adds a new interface to access the global kmsg_redirect
variable by a function to be able to use it in code where
CONFIG_VT_CONSOLE is not set (kernel/panic.c).
This patch:
Instead of using and exporting a global value kmsg_redirect, introduce a
function vt_kmsg_redirect() that both can set and return the console where
messages are printed.
Change all users of kmsg_redirect (the VT code itself and kernel/power.c)
to the new interface.
The main advantage is that vt_kmsg_redirect() can also be used when
CONFIG_VT_CONSOLE is not set.
Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1306) exports the PM runtime workqueue for use by
loadable modules.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Use KERN_CONT in save_image() for printks, so that anybody won't
try to add a loglevel.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Shift the remaining declaration of the variable in_suspend and the
function swsusp_show_speed from swsusp.c to hibernate.c, and delete
swsusp.c.
Signed-off-by: Nigel Cunningham <nigel@tuxonice.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Move hibernation code's functions for allocating and freeing swap
from swsusp.c to swap.c, which is where you'd expect to find them.
Signed-off-by: Nigel Cunningham <nigel@tuxonice.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Finish a line by \n when load_image fails in the middle of loading.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
There are too many retval variables in save_image(). Thus error return
value from snapshot_read_next() may be ignored and only part of the
snapshot (successfully) written.
Remove 'error' variable, invert the condition in the do-while loop
and convert the loop to use only 'ret' variable.
Switch the rest of the function to consider only 'ret'.
Also make sure we end printed line by \n if an error occurs.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
While cruising through the swsusp code I found few blkdev reference
leaks of resume_bdev.
swsusp_read: remove blkdev_put altogether. Some fail paths do
not do that.
swsusp_check: make sure we always put a reference on fail paths
software_resume: all fail paths between swsusp_check and swsusp_read
omit swsusp_close. Add it in those cases. And since
swsusp_read doesn't drop the reference anymore, do
it here unconditionally.
[rjw: Fixed a small coding style issue.]
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Freezing isn't exactly the most latency sensitive operation and
there's no reason to burn cpu cycles and power waiting for it to
complete. msleep(10) instead of yield(). This should improve
reliability of emergency hibernation.
[rjw: Modified the comment next to the msleep(10).]
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Increase TEST_SUSPEND_SECONDS to 10 so the warning in
suspend_test_finish() doesn't annoy the users of slower systems so much.
Also, make the warning print the suspend-resume cycle time, so that we
know why the warning actually triggered.
Patch prepared during the hacking session at the Kernel Summit in Tokyo.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* remove asm/atomic.h inclusion from linux/utsname.h --
not needed after kref conversion
* remove linux/utsname.h inclusion from files which do not need it
NOTE: it looks like fs/binfmt_elf.c do not need utsname.h, however
due to some personality stuff it _is_ needed -- cowardly leave ELF-related
headers and files alone.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since alloc_bootmem() will never return inaccessible (via virtual
addressing) memory anyway, using the ..._low() variant only makes sense
when the physical address range of the allocated memory must fulfill
further constraints, espacially since on 64-bits (or more generally in all
cases where the pools the two variants allocate from are than the full
available range.
Probably the use in alloc_tce_table() could also be eliminated (based on
code inspection of pci-calgary_64.c), but that seems too risky given I
know nothing about that hardware and have no way to test it.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the past someone gratuitiously borrowed chunks of kernel internal vt
code and dumped them in kernel/power. They have all sorts of deep relations
with the vt code so put them in the vt tree instead
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the definition of BM_BITS_PER_BLOCK and kerneldoc
description of create_bm_block_list().
[rjw: Added changelog.]
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Use for_each_populated_zone() instead of for_each_zone() in hibernation
code. This fixes a bug on s390, where we allow both config options
HIBERNATION and MEMORY_HOTPLUG, so that we also have a ZONE_MOVABLE
here. We only allow hibernation if no memory hotplug operation was
performed, so in fact both features can only be used exclusively, but
this way we don't need 2 differently configured (distribution) kernels.
If we have an unpopulated ZONE_MOVABLE, we allow hibernation but run
into a BUG_ON() in memory_bm_test/set/clear_bit() because hibernation
code iterates through all zones, not only the populated zones, in
several places. For example, swsusp_free() does for_each_zone() and
then checks for pfn_valid(), which is true even if the zone is not
populated, resulting in a BUG_ON() later because the pfn cannot be
found in the memory bitmap.
Replacing all occurences of for_each_zone() in hibernation code with
for_each_populated_zone() would fix this issue.
[rjw: Rebased on top of linux-next hibernation patches.]
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
We want to avoid attempting to free too much memory too hard during
hibernation, so estimate the minimum size of the image to use as the
lower limit for preallocating memory.
The approach here is based on the (experimental) observation that we
can't free more page frames than the sum of:
* global_page_state(NR_SLAB_RECLAIMABLE)
* global_page_state(NR_ACTIVE_ANON)
* global_page_state(NR_INACTIVE_ANON)
* global_page_state(NR_ACTIVE_FILE)
* global_page_state(NR_INACTIVE_FILE)
minus
* global_page_state(NR_FILE_MAPPED)
Namely, if this number is subtracted from the number of saveable
pages in the system, we get a good estimate of the minimum reasonable
size of a hibernation image.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Since the hibernation code is now going to use allocations of memory
to make enough room for the image, it can also use the page frames
allocated at this stage as image page frames. The low-level
hibernation code needs to be rearranged for this purpose, but it
allows us to avoid freeing a great number of pages and allocating
these same pages once again later, so it generally is worth doing.
[rev. 2: Take highmem into account correctly.]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Rework swsusp_shrink_memory() so that it calls shrink_all_memory()
just once to make some room for the image and then allocates memory
to apply more pressure to the memory management subsystem, if
necessary.
Unfortunately, we don't seem to be able to drop shrink_all_memory()
entirely just yet, because that would lead to huge performance
regressions in some test cases.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Although the same label name is used somewhere else in the file, this
particular label was consistently typoed in all of its uses.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Introduce a core framework for run-time power management of I/O
devices. Add device run-time PM fields to 'struct dev_pm_info'
and device run-time PM callbacks to 'struct dev_pm_ops'. Introduce
a run-time PM workqueue and define some device run-time PM helper
functions at the core level. Document all these things.
Special thanks to Alan Stern for his help with the design and
multiple detailed reviews of the pereceding versions of this patch
and to Magnus Damm for testing feedback.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@igel.co.jp>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, the following scenario appears to be possible in theory:
* Tasks are frozen for hibernation or suspend.
* Free pages are almost exhausted.
* Certain piece of code in the suspend code path attempts to allocate
some memory using GFP_KERNEL and allocation order less than or
equal to PAGE_ALLOC_COSTLY_ORDER.
* __alloc_pages_internal() cannot find a free page so it invokes the
OOM killer.
* The OOM killer attempts to kill a task, but the task is frozen, so
it doesn't die immediately.
* __alloc_pages_internal() jumps to 'restart', unsuccessfully tries
to find a free page and invokes the OOM killer.
* No progress can be made.
Although it is now hard to trigger during hibernation due to the memory
shrinking carried out by the hibernation code, it is theoretically
possible to trigger during suspend after the memory shrinking has been
removed from that code path. Moreover, since memory allocations are
going to be used for the hibernation memory shrinking, it will be even
more likely to happen during hibernation.
To prevent it from happening, introduce the oom_killer_disabled switch
that will cause __alloc_pages_internal() to fail in the situations in
which the OOM killer would have been called and make the freezer set
this switch after tasks have been successfully frozen.
[akpm@linux-foundation.org: be nicer to the namespace]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Fengguang Wu <fengguang.wu@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The *_nvs_* routines in swsusp.c make use of the io*map()
functions, which are only provided for HAS_IOMEM, thus
breaking compilation if HAS_IOMEM is not set. Fix this
by moving the *_nvs_* routines into hibernate_nvs.c, which
is only compiled if HAS_IOMEM is set.
[rjw: Change the name of the new file to hibernate_nvs.c, add the
license line to the header comment.]
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Change the name of kernel/power/disk.c to kernel/power/hibernate.c
in analogy with the file names introduced by the changes that
separated the suspend to RAM and standby funtionality from the
common PM functions.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Move the suspend to RAM and standby code from kernel/power/main.c
to two separate files, kernel/power/suspend.c containing the basic
functions and kernel/power/suspend_test.c containing the automatic
suspend test facility based on the RTC clock alarm.
There are no changes in functionality related to these modifications.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
A future patch is going to modify the memory shrinking code so that
it will make memory allocations to free memory instead of using an
artificial memory shrinking mechanism for that. For this purpose it
is convenient to move swsusp_shrink_memory() from
kernel/power/swsusp.c to kernel/power/snapshot.c, because the new
memory-shrinking code is going to use things that are local to
kernel/power/snapshot.c .
[rev. 2: Make some functions static and remove their headers from
kernel/power/power.h]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Remove the shrinking of memory from the suspend-to-RAM code, where
it is not really necessary.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
This patch (as1241) renames a bunch of functions in the PM core.
Rather than go through a boring list of name changes, suffice it to
say that in the end we have a bunch of pairs of functions:
device_resume_noirq dpm_resume_noirq
device_resume dpm_resume
device_complete dpm_complete
device_suspend_noirq dpm_suspend_noirq
device_suspend dpm_suspend
device_prepare dpm_prepare
in which device_X does the X operation on a single device and dpm_X
invokes device_X for all devices in the dpm_list.
In addition, the old dpm_power_up and device_resume_noirq have been
combined into a single function (dpm_resume_noirq).
Lastly, dpm_suspend_start and dpm_resume_end are the renamed versions
of the former top-level device_suspend and device_resume routines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Rename the functions performing "_noirq" dev_pm_ops
operations from device_power_down() and device_power_up()
to device_suspend_noirq() and device_resume_noirq().
The new function names are chosen to show that the functions
are responsible for calling the _noirq() versions to finalize
the suspend/resume operation. The current function names do
not perform power down/up anymore so the names may be misleading.
Global function renames:
- device_power_down() -> device_suspend_noirq()
- device_power_up() -> device_resume_noirq()
Static function renames:
- suspend_device_noirq() -> __device_suspend_noirq()
- resume_device_noirq() -> __device_resume_noirq()
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Len Brown <lenb@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
We shouldn't hold dpm_list_mtx while executing
[disable|enable]_nonboot_cpus(), because theoretically this may lead
to a deadlock as shown by the following example (provided by Johannes
Berg):
CPU 3 CPU 2 CPU 1
suspend/hibernate
something:
rtnl_lock() device_pm_lock()
-> mutex_lock(&dpm_list_mtx)
mutex_lock(&dpm_list_mtx)
linkwatch_work
-> rtnl_lock()
disable_nonboot_cpus()
-> flush CPU 3 workqueue
Fortunately, device drivers are supposed to stop any activities that
might lead to the registration of new device objects way before
disable_nonboot_cpus() is called, so it shouldn't be necessary to
hold dpm_list_mtx over the entire late part of device suspend and
early part of device resume.
Thus, during the late suspend and the early resume of devices acquire
dpm_list_mtx only when dpm_list is going to be traversed and release
it right after that.
This patch is reported to fix the regressions tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=13245.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Miles Lane <miles.lane@gmail.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Check the return value of sysdev_suspend(). I think this was a typo.
Without this change, the following "if" check is always false.
I also changed the error message so it's distinguishable from the
similar message a few lines above.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Commit c751085943 ("PM/Hibernate: Wait for
SCSI devices scan to complete during resume") added a call to
scsi_complete_async_scans() to software_resume(), so that it waited for
the SCSI scanning to complete, but the call was added at a wrong place.
Namely, it should have been added after wait_for_device_probe(), which
is called only if the image partition hasn't been specified yet. Also,
it's reasonable to check if the image partition is present and only wait
for the device probing and SCSI scanning to complete if it is not the
case.
Additionally, since noresume is checked right at the beginning of
software_resume() and the function returns immediately if it's set, it
doesn't make sense to check it once again later.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 900af0d973 (PM: Change suspend
code ordering) changed the ordering of suspend code in such a way
that the platform .prepare() callback is now executed after the
device drivers' late suspend callbacks have run. Unfortunately, this
turns out to break ARM platforms that need to talk via I2C to power
control devices during the .prepare() callback.
For this reason introduce two new platform suspend callbacks,
.prepare_late() and .wake(), that will be called just prior to
disabling non-boot CPUs and right after bringing them back on line,
respectively, and use them instead of .prepare() and .finish() for
ACPI suspend. Make the PM core execute the .prepare() and .finish()
platform suspend callbacks where they were executed previously (that
is, right after calling the regular suspend methods provided by
device drivers and right before executing their regular resume
methods, respectively).
It is not necessary to make analogous changes to the hibernation
code and data structures at the moment, because they are only used
by ACPI platforms.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Len Brown <len.brown@intel.com>
There is a race between resume from hibernation and the asynchronous
scanning of SCSI devices and to prevent it from happening we need to
call scsi_complete_async_scans() during resume from hibernation.
In addition, if the resume from hibernation is userland-driven, it's
better to wait for all device probes in the kernel to complete before
attempting to open the resume device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
Make the following header file changes:
- remove arch ifdefs and asm/suspend.h from linux/suspend.h
- add asm/suspend.h to disk.c (for arch_prepare_suspend())
- add linux/io.h to swsusp.c (for ioremap())
- x86 32/64 bit compile fixes
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: cleanup
In almost cases, for_each_zone() is used with populated_zone(). It's
because almost function doesn't need memoryless node information.
Therefore, for_each_populated_zone() can help to make code simplify.
This patch has no functional change.
[akpm@linux-foundation.org: small cleanup]
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the ordering of the hibernation core code so that the platform
"prepare" callbacks are executed and the nonboot CPUs are disabled
after calling device drivers' "late suspend" methods.
This change (along with the previous analogous change of the suspend
core code) will allow us to rework the PCI PM core so that the power
state of devices is changed in the "late" phase of suspend (and
analogously in the "early" phase of resume), which in turn will allow
us to avoid the race condition where a device using shared interrupts
is put into a low power state with interrupts enabled and then an
interrupt (for another device) comes in and confuses its driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Change the ordering of the suspend core code so that the platform
"prepare" callback is executed and the nonboot CPUs are disabled
after calling device drivers' "late suspend" methods.
This change will allow us to rework the PCI PM core so that the power
state of devices is changed in the "late" phase of suspend (and
analogously in the "early" phase of resume), which in turn will allow
us to avoid the race condition where a device using shared interrupts
is put into a low power state with interrupts enabled and then an
interrupt (for another device) comes in and confuses its driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Use the functions introduced in by the previous patch,
suspend_device_irqs(), resume_device_irqs() and check_wakeup_irqs(),
to rework the handling of interrupts during suspend (hibernation) and
resume. Namely, interrupts will only be disabled on the CPU right
before suspending sysdevs, while device drivers will be prevented
from receiving interrupts, with the help of the new helper function,
before their "late" suspend callbacks run (and analogously during
resume).
In addition, since the device interrups are now disabled before the
CPU has turned all interrupts off and the CPU will ACK the interrupts
setting the IRQ_PENDING bit for them, check in sysdev_suspend() if
any wake-up interrupts are pending and abort suspend if that's the
case.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Move the sysdev_suspend/resume from the callee to the callers, with
no real change in semantics, so that we can rework the disabling of
interrupts during suspend/hibernation.
This is based on an earlier patch from Linus.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* hibernate:
PM: Fix suspend_console and resume_console to use only one semaphore
PM: Wait for console in resume
PM: Fix pm_notifiers during user mode hibernation
swsusp: clean up shrink_all_zones()
swsusp: dont fiddle with swappiness
PM: fix build for CONFIG_PM unset
PM/hibernate: fix "swap breaks after hibernation failures"
PM/resume: wait for device probing to finish
Consolidate driver_probe_done() loops into one place
Avoids later waking up to a blinking cursor if the device woke up and
returned to sleep before the console switch happened.
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Snapshot device is opened with O_RDONLY during suspend and O_WRONLY durig
resume. Make sure we also call notifiers with correct parameter telling
them what we are really doing.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Compilation of kprobes.c with CONFIG_PM unset is broken due to some broken
config dependncies. Fix that.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
the resume code does not currently wait for device probing to finish.
Even without async function calls this is dicey and not correct,
but with async function calls during the boot sequence this is going
to get hit more...
This patch adds the synchronization using the newly introduced helper.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: fix deadlock in blk_abort_queue() for drivers that readd to timeout list
block: fix booting from partitioned md array
block: revert part of 18ce3751cc
cciss: PCI power management reset for kexec
paride/pg.c: xs(): &&/|| confusion
fs/bio: bio_alloc_bioset: pass right object ptr to mempool_free
block: fix bad definition of BIO_RW_SYNC
bsg: Fix sense buffer bug in SG_IO
Compilation of kprobes.c with CONFIG_PM unset is broken due to some broken
config dependncies. Fix that.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can't OR shift values, so get rid of BIO_RW_SYNC and use BIO_RW_SYNCIO
and BIO_RW_UNPLUG explicitly. This brings back the behaviour from before
213d9417fe.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Introduce boolean function system_entering_hibernation() returning
'true' during the last phase of hibernation, in which devices are
being put into low power states and the sleep state (for example,
ACPI S4) is finally entered.
Some device drivers need such a function to check if the system is
in the final phase of hibernation. In particular, some SATA drivers
are going to use it for blacklisting systems in which the disks
should not be spun down during the last phase of hibernation (the
BIOS will do that anyway).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reorder the code in kernel/power/main.c to fix compilation warning
triggered by unsetting CONFIG_SUSPEND.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Freezer fails to compile if with the following configuration
settings:
CONFIG_CGROUPS=y
CONFIG_CGROUP_FREEZER=y
CONFIG_MODULES=y
CONFIG_FREEZER=y
CONFIG_PM=y
CONFIG_PM_SLEEP=n
Fix this by making process.o compilation depend on CONFIG_FREEZER.
Reported-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Impact: Reduce stack usage, use new cpumask API.
Mainly changing cpumask_t to 'struct cpumask' and similar simple API
conversion. Two conversions worth mentioning:
1) we use cpumask_any_but to avoid a temporary in kernel/softlockup.c,
2) Use cpumask_var_t in taskstats_user_cmd().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Replace one evaluation of pfn_to_page() in copy_data_pages() with
the value of a local variable containing the right number already.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
It has been requested to make hibernation work with memory
hotplugging enabled and for this purpose the hibernation code has to
be reworked to take the possible overlapping of zones into account.
Thus, rework the hibernation memory bitmaps code to prevent
duplication of PFNs from occuring and add checks to make sure that
one page frame will not be marked as saveable many times.
Additionally, use list.h lists instead of open-coded lists to
implement the memory bitmaps.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
During resume from hibernation using the userland interface image
data are being passed from the used space process to the kernel.
These data need not be valid, but currently the kernel sometimes
oopses if it gets invalid image data, which is wrong. Make the
kernel return error codes to the user space in such cases.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
According to the ACPI Specification 3.0b, Section 15.3.2,
"OSPM will call the _PTS control method some time before entering a
sleeping state, to allow the platform's AML code to update this
memory image before entering the sleeping state. After the system
awakes from an S4 state, OSPM will restore this memory area and call
the _WAK control method to enable the BIOS to reclaim its memory
image." For this reason, implement a mechanism allowing us to save
the NVS memory during hibernation and to restore it during the
subsequent resume.
Based on a patch by Zhang Rui.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Call platform_begin() before swsusp_shrink_memory() so that we can
always allocate enough memory to save the ACPI NVS region from
platform_begin().
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
it had been put there to mark the call of blkdev_put() that
needed proper argument propagated to it; later patch in the
same series had done just that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Impact: widen function-tracing to suspend+resume (and hibernation) sequences
Now that the ftrace kernel thread is gone, we can allow tracing
during suspend/resume again.
So revert these two commits:
f42ac38c5 "ftrace: disable tracing for suspend to ram"
41108eb10 "ftrace: disable tracing for hibernation"
This should be tested very carefully, as it could interact with
altneratives instruction patching, etc.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
By using WARN(), kerneloops.org can collect which component is causing
the delay and make statistics about that. suspend_test_finish() is
currently the number 2 item but unless we can collect who's causing
it we're not going to be able to fix the hot topic ones..
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Insufficient dependency - we really want CONFIG_RTC_CLASS=y there.
That will give us CONFIG_RTC_LIB=y, so the old dependency can be
simply replaced.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* get rid of fake struct file/struct dentry in __blkdev_get()
* merge __blkdev_get() and do_open()
* get rid of flags argument of blkdev_get()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When a system is resumed after a suspend, it will also unfreeze frozen
cgroups.
This patchs modifies the resume sequence to skip the tasks which are part
of a frozen control group.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Tested-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements a new freezer subsystem in the control groups
framework. It provides a way to stop and resume execution of all tasks in
a cgroup by writing in the cgroup filesystem.
The freezer subsystem in the container filesystem defines a file named
freezer.state. Writing "FROZEN" to the state file will freeze all tasks
in the cgroup. Subsequently writing "RUNNING" will unfreeze the tasks in
the cgroup. Reading will return the current state.
* Examples of usage :
# mkdir /containers/freezer
# mount -t cgroup -ofreezer freezer /containers
# mkdir /containers/0
# echo $some_pid > /containers/0/tasks
to get status of the freezer subsystem :
# cat /containers/0/freezer.state
RUNNING
to freeze all tasks in the container :
# echo FROZEN > /containers/0/freezer.state
# cat /containers/0/freezer.state
FREEZING
# cat /containers/0/freezer.state
FROZEN
to unfreeze all tasks in the container :
# echo RUNNING > /containers/0/freezer.state
# cat /containers/0/freezer.state
RUNNING
This is the basic mechanism which should do the right thing for user space
task in a simple scenario.
It's important to note that freezing can be incomplete. In that case we
return EBUSY. This means that some tasks in the cgroup are busy doing
something that prevents us from completely freezing the cgroup at this
time. After EBUSY, the cgroup will remain partially frozen -- reflected
by freezer.state reporting "FREEZING" when read. The state will remain
"FREEZING" until one of these things happens:
1) Userspace cancels the freezing operation by writing "RUNNING" to
the freezer.state file
2) Userspace retries the freezing operation by writing "FROZEN" to
the freezer.state file (writing "FREEZING" is not legal
and returns EIO)
3) The tasks that blocked the cgroup from entering the "FROZEN"
state disappear from the cgroup's set of tasks.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: export thaw_process]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Tested-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the TIF_FREEZE flag is available in all architectures, extract
the refrigerator() and freeze_task() from kernel/power/process.c and make
it available to all.
The refrigerator() can now be used in a control group subsystem
implementing a control group freezer.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Tested-by: Matt Helsley <matthltc@us.ibm.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We currently use a PM notifier to disable user mode helpers before suspend
and hibernation and to re-enable them during resume. However, this is not
an ideal solution, because if any drivers want to upload firmware into
memory before suspend, they have to use a PM notifier for this purpose and
there is no guarantee that the ordering of PM notifiers will be as
expected (ie. the notifier that disables user mode helpers has to be run
after the driver's notifier used for uploading the firmware).
For this reason, it seems better to move the disabling and enabling of
user mode helpers to separate functions that will be called by the PM core
as necessary.
[akpm@linux-foundation.org: remove unneeded ifdefs]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In accordance with commit f42ac38c59
("ftrace: disable tracing for suspend to ram"), disable tracing
around the suspend code in hibernation code paths.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I've been painstakingly debugging the issue with suspend to ram and
ftraced. The 2.6.28 code does not have this issue, but since the mcount
recording is not going to be in 27, this must be solved for the ftrace
daemon version.
The resume from suspend to ram would reboot because it was triple
faulting. Debugging further, I found that calling the mcount function
itself was not an issue, but it would fault when it incremented
preempt_count. preempt_count is on the tasks info structure that is on the
low memory address of the task's stack. For some reason, it could not
write to it. Resuming out of suspend to ram does quite a lot of funny
tricks to get to work, so it is not surprising at all that simply doing a
preempt_disable() would cause a fault.
Thanks to Rafael for suggesting to add a "while (1);" to find the place in
resuming that is causing the fault. I would place the loop somewhere in
the code, compile and reboot and see if it would either reboot (hit the
fault) or simply hang (hit the loop). Doing this over and over again, I
narrowed it down that it was happening in enable_nonboot_cpus.
At this point, I found that it is easier to simply disable tracing around
the suspend code, instead of searching for the particular function that
can not handle doing a preempt_disable.
This patch disables the tracer as it suspends and reenables it on resume.
I tested this patch on my Laptop, and it can resume fine with the patch.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements devices state save/restore before after kexec.
This patch together with features in kexec_jump patch can be used for
following:
- A simple hibernation implementation without ACPI support. You can kexec a
hibernating kernel, save the memory image of original system and shutdown
the system. When resuming, you restore the memory image of original system
via ordinary kexec load then jump back.
- Kernel/system debug through making system snapshot. You can make system
snapshot, jump back, do some thing and make another system snapshot.
- Cooperative multi-kernel/system. With kexec jump, you can switch between
several kernels/systems quickly without boot process except the first time.
This appears like swap a whole kernel/system out/in.
- A general method to call program in physical mode (paging turning
off). This can be used to invoke BIOS code under Linux.
The following user-space tools can be used with kexec jump:
- kexec-tools needs to be patched to support kexec jump. The patches
and the precompiled kexec can be download from the following URL:
source: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec-tools-src_git_kh10.tar.bz2
patches: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec-tools-patches_git_kh10.tar.bz2
binary: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec_git_kh10
- makedumpfile with patches are used as memory image saving tool, it
can exclude free pages from original kernel memory image file. The
patches and the precompiled makedumpfile can be download from the
following URL:
source: http://khibernation.sourceforge.net/download/release_v10/makedumpfile/makedumpfile-src_cvs_kh10.tar.bz2
patches: http://khibernation.sourceforge.net/download/release_v10/makedumpfile/makedumpfile-patches_cvs_kh10.tar.bz2
binary: http://khibernation.sourceforge.net/download/release_v10/makedumpfile/makedumpfile_cvs_kh10
- An initramfs image can be used as the root file system of kexeced
kernel. An initramfs image built with "BuildRoot" can be downloaded
from the following URL:
initramfs image: http://khibernation.sourceforge.net/download/release_v10/initramfs/rootfs_cvs_kh10.gz
All user space tools above are included in the initramfs image.
Usage example of simple hibernation:
1. Compile and install patched kernel with following options selected:
CONFIG_X86_32=y
CONFIG_RELOCATABLE=y
CONFIG_KEXEC=y
CONFIG_CRASH_DUMP=y
CONFIG_PM=y
CONFIG_HIBERNATION=y
CONFIG_KEXEC_JUMP=y
2. Build an initramfs image contains kexec-tool and makedumpfile, or
download the pre-built initramfs image, called rootfs.gz in
following text.
3. Prepare a partition to save memory image of original kernel, called
hibernating partition in following text.
4. Boot kernel compiled in step 1 (kernel A).
5. In the kernel A, load kernel compiled in step 1 (kernel B) with
/sbin/kexec. The shell command line can be as follow:
/sbin/kexec --load-preserve-context /boot/bzImage --mem-min=0x100000
--mem-max=0xffffff --initrd=rootfs.gz
6. Boot the kernel B with following shell command line:
/sbin/kexec -e
7. The kernel B will boot as normal kexec. In kernel B the memory
image of kernel A can be saved into hibernating partition as
follow:
jump_back_entry=`cat /proc/cmdline | tr ' ' '\n' | grep kexec_jump_back_entry | cut -d '='`
echo $jump_back_entry > kexec_jump_back_entry
cp /proc/vmcore dump.elf
Then you can shutdown the machine as normal.
8. Boot kernel compiled in step 1 (kernel C). Use the rootfs.gz as
root file system.
9. In kernel C, load the memory image of kernel A as follow:
/sbin/kexec -l --args-none --entry=`cat kexec_jump_back_entry` dump.elf
10. Jump back to the kernel A as follow:
/sbin/kexec -e
Then, kernel A is resumed.
Implementation point:
To support jumping between two kernels, before jumping to (executing)
the new kernel and jumping back to the original kernel, the devices
are put into quiescent state, and the state of devices and CPU is
saved. After jumping back from kexeced kernel and jumping to the new
kernel, the state of devices and CPU are restored accordingly. The
devices/CPU state save/restore code of software suspend is called to
implement corresponding function.
Known issues:
- Because the segment number supported by sys_kexec_load is limited,
hibernation image with many segments may not be load. This is
planned to be eliminated by adding a new flag to sys_kexec_load to
make a image can be loaded with multiple sys_kexec_load invoking.
Now, only the i386 architecture is supported.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cope with a quirk of some RTCs (notably ACPI ones) which aren't guaranteed
to implement oneshot behavior when they woke the system from sleeep:
forcibly disable the alarm, just in case.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix try_to_freeze_tasks()'s use of do_div() on an s64 by making
elapsed_csecs64 a u64 instead and dividing that.
Possibly this should be guarded lest the interval calculation turn up
negative, but the possible negativity of the result of the division is
cast away anyway.
This was introduced by patch 438e2ce68d.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
schedule sysrq poweroff on boot cpu.
sysrq poweroff needs to disable nonboot cpus, and we need to run this on boot
cpu to avoid any recursion. http://bugzilla.kernel.org/show_bug.cgi?id=10897
[kosaki.motohiro@jp.fujitsu.com: build fix]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Rus <harbour@sfinx.od.ua>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch simplifies the memory bitmap manipulations.
- remove the member size in struct bm_block
It is not necessary for struct bm_block to have the number of bit chunks that
can be calculated by using end_pfn and start_pfn.
- use find_next_bit() for memory_bm_next_pfn
No need to invent the bitmap library only for the memory bitmap.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Boot-time test for system suspend states (STR or standby). The generic
RTC framework triggers wakeup alarms, which are used to exit those states.
- Measures some aspects of suspend time ... this uses "jiffies" until
someone converts it to use a timebase that works properly even while
timer IRQs are disabled.
- Triggered by a command line parameter. By default nothing even
vaguely troublesome will happen, but "test_suspend=mem" will give
you a brief STR test during system boot. (Or you may need to use
"test_suspend=standby" instead, if your hardware needs that.)
This isn't without problems. It fires early enough during boot that for
example both PCMCIA and MMC stacks have misbehaved. The workaround in
those cases was to boot without such media cards inserted.
[matthltc@us.ibm.com: fix compile failure in boot time suspend selftest]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Pavel Machek <pavel@suse.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Xen save/restore needs bits of code enabled by PM_SLEEP, and PM_SLEEP
depends on PM. So make XEN_SAVE_RESTORE depend on PM and PM_SLEEP
depend on XEN_SAVE_RESTORE.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
Revert "x86/PCI: ACPI based PCI gap calculation"
PCI: remove unnecessary volatile in PCIe hotplug struct controller
x86/PCI: ACPI based PCI gap calculation
PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
PCI PM: Fix pci_prepare_to_sleep
x86/PCI: Fix PCI config space for domains > 0
Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
PCI: Simplify PCI device PM code
PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
PCI ACPI: Rework PCI handling of wake-up
ACPI: Introduce new device wakeup flag 'prepared'
ACPI: Introduce acpi_device_sleep_wake function
PCI: rework pci_set_power_state function to call platform first
PCI: Introduce platform_pci_power_manageable function
ACPI: Introduce acpi_bus_power_manageable function
PCI: make pci_name use dev_name
PCI: handle pci_name() being const
PCI: add stub for pci_set_consistent_dma_mask()
PCI: remove unused arch pcibios_update_resource() functions
PCI: fix pci_setup_device()'s sprinting into a const buffer
...
Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
We can avoid taking the BKL in snapshot_ioctl() if pm_mutex is used to prevent
the ioctls from being executed concurrently.
In addition, although it is only possible to open /dev/snapshot once, the task
which has done that may spawn a child that will inherit the open descriptor,
so in theory they can call snapshot_write(), snapshot_read() and
snapshot_release() concurrently. pm_mutex can also be used for mutual
exclusion in such cases.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Push BKL down into ioctl handlers - snapshot device.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
The freezer currently attempts to distinguish kernel threads from
user space tasks by checking if their mm pointer is unset and it
does not send fake signals to kernel threads. However, there are
kernel threads, mostly related to networking, that behave like
user space tasks and may want to be sent a fake signal to be frozen.
Introduce the new process flag PF_FREEZER_NOSIG that will be set
by default for all kernel threads and make the freezer only send
fake signals to the tasks having PF_FREEZER_NOSIG unset. Provide
the set_freezable_with_signal() function to be called by the kernel
threads that want to be sent a fake signal for freezing.
This patch should not change the freezer's observable behavior.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit 6fbbec428c8e7bb617da2e8a589af2e97bcf3bc4.
Rafael doesnt like it - it breaks various assumptions.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Xen save/restore requires PM_SLEEP to be set without requiring
SUSPEND or HIBERNATION.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
ACPI PM: Add possibility to change suspend sequence
There are some systems out there that don't work correctly with
our current suspend/hibernation code ordering. Provide a workaround
for these systems allowing them to pass 'acpi_sleep=old_ordering' in
the kernel command line so that it will use the pre-ACPI 2.0 ("old")
suspend code ordering.
Unfortunately, this requires us to add a platform hook to the
resuming of devices for recovering the platform in case one of the
device drivers' .suspend() routines returns error code. Namely,
ACPI 1.0 specifies that _PTS should be called before suspending
devices, but _WAK still should be called before resuming them in
order to undo the changes made by _PTS. However, if there is an
error during suspending devices, they are automatically resumed
without returning control to the PM core, so the _WAK has to be
called from within device_resume() in that cases.
The patch also reorders and refactors the ACPI suspend/hibernation
code to avoid duplication as far as reasonably possible.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce 'struct pm_ops' and 'struct pm_ext_ops' ('ext' meaning
'extended') representing suspend and hibernation operations for bus
types, device classes, device types and device drivers.
Modify the PM core to use 'struct pm_ops' and 'struct pm_ext_ops'
objects, if defined, instead of the ->suspend(), ->resume(),
->suspend_late(), and ->resume_early() callbacks (the old callbacks
will be considered as legacy and gradually phased out).
The main purpose of doing this is to separate suspend (aka S2RAM and
standby) callbacks from hibernation callbacks in such a way that the
new callbacks won't take arguments and the semantics of each of them
will be clearly specified. This has been requested for multiple
times by many people, including Linus himself, and the reason is that
within the current scheme if ->resume() is called, for example, it's
difficult to say why it's been called (ie. is it a resume from RAM or
from hibernation or a suspend/hibernation failure etc.?).
The second purpose is to make the suspend/hibernation callbacks more
flexible so that device drivers can handle more than they can within
the current scheme. For example, some drivers may need to prevent
new children of the device from being registered before their
->suspend() callbacks are executed or they may want to carry out some
operations requiring the availability of some other devices, not
directly bound via the parent-child relationship, in order to prepare
for the execution of ->suspend(), etc.
Ultimately, we'd like to stop using the freezing of tasks for suspend
and therefore the drivers' suspend/hibernation code will have to take
care of the handling of the user space during suspend/hibernation.
That, in turn, would be difficult within the current scheme, without
the new ->prepare() and ->complete() callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Prior to suspend, we allocate and switch to a new VT; after suspend, we switch
back to the original VT. This can be slow, and is completely unnecessary if
the framebuffer we're using can restore video properly.
This adds a hook that allows drivers to select whether or not to do this vt
switch, and changes the gxfb driver to call this hook. It also adds a module
param to gxfb to allow controlling of the vt switch (defaulting to no switch).
(Note: I'm not convinced that console_sem is the best way to protect this, but
we should probably have some form of locking..)
[akpm@linux-foundation.org: build fix]
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
AFAICT pm_send_all is a nop when noone uses pm_register...
Hmm.. can we just force CONFIG_PM_LEGACY=n, and see what happens?
Or maybe this is better idea? It may break build somewhere, but it
should be easy to fix... (it builds here, i386 and x86-64).
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Move 00-INDEX entries to power/00-INDEX (and add entry for
pm_qos_interface.txt).
Update references to moved filenames.
Fix some trailing whitespace.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There is a problem in the hibernation code that triggers on some NUMA
systems on which pfn_valid() returns 'true' for some PFNs that don't
belong to any zone. Namely, there is a BUG_ON() in
memory_bm_find_bit() that triggers for PFNs not belonging to any
zone and passing the pfn_valid() test. On the affected systems it
triggers when we mark PFNs reported by the platform as not saveable,
because the PFNs in question belong to a region mapped directly using
iorepam() (i.e. the ACPI data area) and they pass the pfn_valid()
test.
Modify memory_bm_find_bit() so that it returns an error if given PFN
doesn't belong to any zone instead of crashing the kernel and ignore
the result returned by it in mark_nosave_pages(), while marking the
"nosave" memory regions.
This doesn't affect the hibernation functionality, as we won't touch
the PFNs in question anyway.
http://bugzilla.kernel.org/show_bug.cgi?id=9966 .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This changes the "freezer" code used by suspend/hibernate in its treatment
of tasks in TASK_STOPPED (job control stop) and TASK_TRACED (ptrace) states.
As I understand it, the intent of the "freezer" is to hold all tasks
from doing anything significant. For this purpose, TASK_STOPPED and
TASK_TRACED are "frozen enough". It's possible the tasks might resume
from ptrace calls (if the tracer were unfrozen) or from signals
(including ones that could come via timer interrupts, etc). But this
doesn't matter as long as they quickly block again while "freezing" is
in effect. Some minor adjustments to the signal.c code make sure that
try_to_freeze() very shortly follows all wakeups from both kinds of
stop. This lets the freezer code safely leave stopped tasks unmolested.
Changing this fixes the longstanding bug of seeing after resuming from
suspend/hibernate your shell report "[1] Stopped" and the like for all
your jobs stopped by ^Z et al, as if you had freshly fg'd and ^Z'd them.
It also removes from the freezer the arcane special case treatment for
ptrace'd tasks, which relied on intimate knowledge of ptrace internals.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the last step of hibernation in the "platform" mode (with the
help of ACPI) we use the suspend code, including the devices'
->suspend() methods, to prepare the system for entering the ACPI S4
system sleep state.
But at least for some devices the operations performed by the
->suspend() callback in that case must be different from its operations
during regular suspend.
For this reason, introduce the new PM event type PM_EVENT_HIBERNATE and
pass it to the device drivers' ->suspend() methods during the last phase
of hibernation, so that they can distinguish this case and handle it as
appropriate. Modify the drivers that handle PM_EVENT_SUSPEND in a
special way and need to handle PM_EVENT_HIBERNATE in the same way.
These changes are necessary to fix a hibernation regression related
to the i915 driver (ref. http://lkml.org/lkml/2008/2/22/488).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make hibernation work with CONFIG_DEBUG_PAGEALLOC set on x86, by
checking if the pages to be copied are marked as present in the
kernel mapping and temporarily marking them as present if that's not
the case. No functional modifications are introduced if
CONFIG_DEBUG_PAGEALLOC is unset.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
resume_file[] and create_image() can become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Add comments explaing how drain_pages() works.
- Eliminate useless functions
- Rename drain_all_local_pages to drain_all_pages(). It does drain
all pages not only those of the local processor.
- Eliminate useless interrupt off / on sequences. drain_pages()
disables interrupts on its own. The execution thread is
pinned to processor by the caller. So there is no need to
disable interrupts.
- Put drain_all_pages() declaration in gfp.h and remove the
declarations from suspend.h and from mm/memory_hotplug.c
- Make software suspend call drain_all_pages(). The draining
of processor local pages is may not the right approach if
software suspend wants to support SMP. If they call drain_all_pages
then we can make drain_pages() static.
[akpm@linux-foundation.org: fix build]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Following the recent change in the suspend code path, switch consoles before
calling PM notifiers during hibernation.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
In order to fix APM emulation it is necessary to enable apm-emulation
notifications for suspends triggered in various ways via the suspend
notifiers. However, this will cause the systems using APM emulation
to lock up between X being needed to switch away from the VT and X
already waiting for resume in the APM ioctl.
This patch moves the console switch (if enabled) before the suspend
notification (and after the resume notification) to avoid this issue.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch makes the freezer optional for suspend to allow the
system to work (or not work) like the original PMU suspend.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce global hibernation callback .end() and rename global
hibernation callback .start() to .begin(), in analogy with the
recent modifications of the global suspend callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
On ACPI systems the target state set by acpi_pm_set_target() is
reset by acpi_pm_finish(), but that need not be called if the
suspend fails. All platforms that use the .set_target() global
suspend callback are affected by analogous issues.
For this reason, we need an additional global suspend callback that
will reset the target state regardless of whether or not the suspend
is successful. Also, it is reasonable to rename the .set_target()
callback, since it will be used for a different purpose on ACPI
systems (due to ACPI 1.0x code ordering requirements).
Introduce the global suspend callback .end() to be executed at the
end of the suspend sequence and rename the .set_target() global
suspend callback to .begin().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
kernel/power/main.c:488: error: ‘pm_test_attr’ undeclared here (not in a function)
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This cleans up the suspend Kconfig and removes the need to
declare centrally which architectures support suspend. All
architectures that currently support suspend are modified
accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This cleans up the hibernation Kconfig and removes the need to
declare centrally which architectures support hibernation. All
architectures that currently support hibernation are modified
accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Make hibernation messages start with one common prefix "PM: " and use
the word "hibernation" in the messages as a synonym of "suspend to
disk".
Turn some KERN_INFO messages into debug ones.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Make suspend messages start with one common prefix "PM: ".
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove the unnecessary extern declaration of resume_file[]
from kernel/power/swap.c .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix a comment in kernel/power/disk.c so that it doesn't contain lines
longer that 80 characters.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix a comment in kernel/power/main.c so that it doesn't contain lines
longer that 80 characters.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Move the low level restore code to kernel/power/disk.c , since the
corresponding low level hibernation code is already there.
Make restore fail if device_power_down(PMSG_PRETHAW) returns an
error.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Suspend: Make debug facility depend on CONFIG_SUSPEND
Make the new suspend debug facility code depend on CONFIG_SUSPEND,
as appropriate, to remove the compiler warning printed when CONFIG_PM is set
and CONFIG_SUSPEND is not set.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch (as1008b) converts the PM notifier routines from inline
calls to out-of-line code. It also prevents pm_chain_head from
being created when CONFIG_PM_SLEEP isn't enabled, and EXPORTs the
notifier registration and unregistration routines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
When trying to debug a suspend failure I started implementing
PM_TRACE for powerpc. I then noticed that I'm debugging a suspend
failure and so PM_TRACE isn't useful at all, but thought that
nonetheless this could be useful in the future.
Basically, to support PM_TRACE, you add a Kconfig option that
selects PM_TRACE and provides the infrastructure as per the
help text of PM_TRACE.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Make it possible to test the hibernation core code with the help of the
/sys/power/pm_test attribute introduced for suspend testing in the previous
patch.
Writing an appropriate string to this file causes the hibernation code to work
in one of the test modes defined as follows:
freezer
- test the freezing of processes
devices
- test the freezing of processes and suspending of devices
platform
- test the freezing of processes, suspending of devices and platform global
control methods(*)
processors
- test the freezing of processes, suspending of devices, platform global
control methods(*) and the disabling of nonboot CPUs
core
- test the freezing of processes, suspending of devices, platform global
control methods(*), the disabling of nonboot CPUs and suspending of
platform/system devices
(*) - the platform global control methods are only available on ACPI systems
and are only tested if the hibernation mode is set to "platform"
Then, if a hibernation is started by normal means, the hibernation core will
perform its normal operations up to the point indicated by given test level.
Next, it will wait for 5 seconds and carry out the resume operations needed to
transition the system back to the fully functional state.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce sysfs attribute /sys/power/pm_test allowing one to test the suspend
core code. Namely, writing one of the strings:
freezer
devices
platform
processors
core
to this file causes the suspend code to work in one of the test modes defined as
follows:
freezer
- test the freezing of processes
devices
- test the freezing of processes and suspending of devices
platform
- test the freezing of processes, suspending of devices and platform global
control methods(*)
processors
- test the freezing of processes, suspending of devices, platform global
control methods and the disabling of nonboot CPUs
core
- test the freezing of processes, suspending of devices, platform global
control methods, the disabling of nonboot CPUs and suspending of
platform/system devices
(*) These are ACPI global control methods on ACPI systems
Then, if a suspend is started by normal means, the suspend core will perform
its normal operations up to the point indicated by given test level. Next, it
will wait for 5 seconds and carry out the resume operations needed to transition
the system back to the fully functional state.
Writing "none" to /sys/power/pm_test turns the testing off.
When open for reading, /sys/power/pm_test contains a space-separated list of all
available tests (including "none" that represents the normal functionality) in
which the current test level is indicated by square brackets.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Add PM_RESTORE_PREPARE and PM_POST_RESTORE notifiers to the PM core, to be used
in analogy with the existing PM_HIBERNATION_PREPARE and PM_POST_HIBERNATION
notifiers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch moves the prototypes of count_highmem_pages() and
restore_highmem() to kernel/power/power.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Move the definitions of hibernation ioctls to a separate header file in
include/linux, which can be exported to the user space.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Three ioctl numbers belonging to the hibernation userland interface,
SNAPSHOT_ATOMIC_SNAPSHOT, SNAPSHOT_AVAIL_SWAP, SNAPSHOT_GET_SWAP_PAGE,
are defined in a wrong way (eg. not portable). Provide new ioctl numbers for
these ioctls and mark the existing ones as deprecated.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>