Change the menu title to refer to "Renesas SoCs" instead of "SuperH", as
both SuperH and ARM SoCs are supported.
Since commit 9b5ba0df4e ("ARM: shmobile: Introduce ARCH_RENESAS")
is ARCH_RENESAS a more appropriate platform dependency for Renesas ARM
SoCs than the legacy ARCH_SHMOBILE, hence use the former.
Renesas SuperH SH-Mobile SoCs are still covered by the SUPERH
dependency.
This will allow to drop ARCH_SHMOBILE on ARM and ARM64 in the near
future.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SIU sound peripheral is used only on SuperH SH-Mobile platforms.
As both SUPERH and ARCH_SHMOBILE are set for these platforms, the SUPERH
dependency can be dropped.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is waiting udelay(50) x 1024 (= 50ms) for status check
in worst case, but it is overkill.
And we shouldn't use udelay() for 50us
(linux/Documentation/timers/timers-howto.txt)
Waiting maximum udelay(5) x 1024 (= 5ms) is very enough
for status check.
This patch fixes these issue.
Reported-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 4821d914fe ("ASoC: rsnd: use dma_sync_single_for_xxx() for
IOMMU") (= v1) which have been already reverted had supported IPMMU
support on rsnd driver.
Because memory allocating timing and DMAEngine access timing were
different, it used continuous memory and called dma map function by
itself.
OTOH, it is using DMA descriptor mode (= DMA cyclic mode), thus, there
was timing conflict between DMA sync/unsync and DMA transfer starting,
and it maked sound noise.
This patch supports IPMMU with coherent memory, and, it uses Audio DMAC
dev for allocating memory by snd_pcm_lib_preallocate_pages_for_all() to
indicate memory area to IPMMU.
One note is that Playback/Capture need each paired Audio DMAC dev.
Because of this, we need to keep each paired Audio DMAC dev when probing,
and use it when allocating each memory for IPMMU.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ssi.c is assuming below 2 things to probing HDMI node.
1) remote node is including "hdmi0" or "hdmi1" in node name
2) remote_ep->full_name is including full path name
But, these assumptions are broken by below
1) Node names should not use numerical suffixes
commit 6b5ac2f1cb ("arm64: dts: renesas: r8a7795: Drop bogus HDMI
node names suffixes")
2) node full_name no longer include full path name
commit a7e4cfb0a7 ("of/fdt: only store the device node basename
in full_name")
Because of these reasons, ssi.c can't probe HDMI on current kernel.
This patch probes HDMI0/1 by using its address.
Note is that we need to keep updating for this address for future
generation chip.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd driver is supporting Gen3. The difference between Gen1 and Gen2
were very big, but, between Gen2 and Gen3 are not so much.
Thus, it is assuming Gen2 and Gen3 have compatible, therefore,
there is no RSND_GEN3 and rsnd_is_gen3() macro.
But in the future, it will need Gen2 and Gen3 different operation,
and for Gen4.
This patch adds missing RSND_GEN3 and rsnd_is_gen3() macro.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_cmd_mod_get() is used from cmd.c only.
Let's makes it static function
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The suspend/resume callbacks are now optional, leading to a warning
when they are unused:
sound/soc/sh/rcar/core.c:1548:12: error: 'rsnd_resume' defined but not used [-Werror=unused-function]
static int rsnd_resume(struct device *dev)
^~~~~~~~~~~
sound/soc/sh/rcar/core.c:1539:12: error: 'rsnd_suspend' defined but not used [-Werror=unused-function]
static int rsnd_suspend(struct device *dev)
This marks the as __maybe_unused to avoid the warning.
Fixes: f8a9a29c4f ("ASoC: rsnd: set pm_ops in hibernate-compatible way")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use SET_SYSTEM_SLEEP_PM_OPS() macro instead of direct assignment to
.suspend and .resume fields.
This makes driver working after restore from hibernation.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dai_call() is using dev_dbg(), but its message is sometimes
blocks nessesary other messages. If RSND_DEBUG_NO_DAI_CALL was
defined it will be suppressed by this patch.
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI/SRC have under/over flow error handling, and its status is useful
for debuging. But sometimes it might be too much message,
and it might blocks necessity other information.
To avoid such situation, basically this patch indicates interrupt
status debug message if DEBUG was defined, but it will be suppressed
if RSND_DEBUG_NO_IRQ_STATUS was defined.
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BRGCKR should use 0x80770000, instead of 0x80FF0000.
R-Car Gen2 xxx_TIMSEL should use 0x0F1F,
R-Car Gen3 xxx_TIMSEL should use 0x1F1F.
Here, Gen3 doesn't support AVD, thus, both case can use 0x0F1F.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI had shared counting pointer position method between PIO/DMA mode
before. But now DMA mode is using DMAEngine feature to get it.
Thus, this counting pointer position method is needed for only PIO mode.
We don't need to share code anymore.
This patch names PIO related functions as rsnd_ssi_pio_xxx(), and
merged/cleanuped each feature.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is judging 16bit/24bit data by using
runtime->sample_bits, but it is indicating physical size,
not format size. This is confusable code.
This patch uses snd_pcm_format_width() to be more correct code.
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Renesas sound device, DALIGN which exchanges channel position
is needed because SW and HW are using defferent data order if
16bit data. It is not needed when 24bit data.
rsnd_get_dalign() returns necessary value, but it was confusable
code. This patch makes it more simple.
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
period_pos can always be calculated by byte_pos and
byte_per_period, there is no reason to maintain this
variable in rsnd_dai_stream.
This patch removes period_pos from rsnd_ssi and calculates
next_period_byte with consideration of actual byte_pos value.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently there is race condition between set of byte_pos and wrap
it around when new buffer starts. If .pointer is called in-between
it will result in inconsistent pointer position be returned
from .pointer callback.
This patch increments buffer pointer atomically to avoid this issue.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Reviewed-by: Takashi Sakamoto <takashi.sakamoto@miraclelinux.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA handler had needed to calculate pointer before, but it doesn't
need now. Thus, we can remove unnecessary spin lock from DMAC handler.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound needs 8ch clock if TDM 6ch mode, and needs 2ch clock for
6ch or 8ch sound if Multi SSI mode. And these are related to before/after
CTU (= Channel Transfer Unit).
To calculate these we already has rsnd_runtime_channel_for_ssi() which
returns runtime necessary channels.
But, it based on runtime->channels which is not yet set when hw refine.
We need to use hw_params instead of runtime->xxx when hw refine,
and it is not needed after runtime was set.
This patch adds new hw_params on rsnd_dai_stream, and it will be removed
on rsnd_hw_params().
This is very temporary durty code, but it seems no choice at this point.
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car sound driver should be stopped if unbinded during
playbacking/capturing. Otherwise clock open/close counter mismatch
happen.
One note is that we can't skip from remove function (= return -Exxx)
in such case if user used unbind. Because unbind function doesn't
check return value from each driver's remove function.
This means we must to stop and remove driver in remove function.
Now ASoC has snd_soc_disconnect_sync() for this purpose.
Let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
register SSI_MODE is set when SSI works in TDM Extended,
but it isn't reset when SSI starts to work in other modes,
thus causes issues.
This patch clearss SSI_MODE register when SSI works in modes
other than TDM Extended.
Fixes: 186fadc132 ("ASoC: rsnd: add TDM Extend Mode support")
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 4821d914fe ("ASoC: rsnd: use dma_sync_single_for_xxx() for
IOMMU") had supported IOMMU, but it breaks normal sound "recorde"
and both PulseAudio's "playback/recorde". The sound will be noisy.
That commit was using dma_sync_single_for_xxx(), and driver should
make sure memory is protected during CPU or Device are using it.
But if driver returns current "residue" data size correctly on pointer
function, player/recorder will access to protected memory.
IOMMU feature should be supported, but I don't know how to handle it
without memory cache problem at this point.
Thus, this patch simply revert it to avoid current noisy sound.
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Tested-by: Ryo Kodama <ryo.kodama.vz@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I've been quite lax in sending these due to conference season but here's
a fairly large collection of ASoC updates. The one thing that's not
device specific is Takashi's fix for races between delayed work and PCM
destruction, otherwise everything is specific to an individual device.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlnx7QsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0H6gB/9Kg6nfaNQDH3ScDO/0KXJevvc9DZUG
1Mgb6o866WQKVKwHL4/7PeUnwpaAh/Dr5KN7bFS7nImrZlHiJfv64Cmrrca+VMwa
O9SnAxbzMDN1MXV3uLDlmd5jJ2EETGnSSo31gjyOuFAmvWRYhtvN4QtoLRBQYYJ9
A32JAKYXKpdjYlIq8sssf1Ey9OcReho3klAc578Yw5qsuHTsB8yJ5SNy0YgmobCm
rNs+LcY9fBPQxY1nVW5iJ3L8oR9RXlUOdZy1I220i0q6+ku1nynbh64V8m7fFGmp
KQLIVvH8JGlqaGBidU47C3vwEnUN88y0+98i9dF4Hc26E+Ml3YNyL/z6
=TVgt
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAloGGn8THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0BAsB/9tbgkbKpUVsWEQOTXDtz1VARb5+zxJ
zMRmYGdcfV+au4pmo07NwcxwFDqeLxmsd7dRM+eoPJGbxklD9rr9eL9tZiO1TI0B
jla9eyKO1aRjCD8dEDsQJEUjDGWWbrpYRvFjlTmYW5cf1vgE9Ta7QtwBN+mK+Ssn
1PtwfHg5lDffoCMGOgu/5Kah4QhzAIU1mM4Vg77VgsuScZEw5qMYJUncfkdsH6M5
JiQJpOQR/wNL4/IETodjhFzqhi9vlUvDEfmATNMpHMdHA//erUbphUt2bAjqVauM
zKTFTSN1vvW1GirJyxz4NiHXQ6upbpZPMDcPsfOzJhHw82OAwx/pp1QT
=bBtM
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.14-rc6' into asoc-linus
ASoC: Fixes for v4.14
I've been quite lax in sending these due to conference season but here's
a fairly large collection of ASoC updates. The one thing that's not
device specific is Takashi's fix for races between delayed work and PCM
destruction, otherwise everything is specific to an individual device.
# gpg: Signature made Thu 26 Oct 2017 15:11:23 BST
# gpg: using RSA key ADE668AA675718B59FE29FEA24D68B725D5487D0
# gpg: issuer "broonie@kernel.org"
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>" [unknown]
# gpg: aka "Mark Brown <broonie@debian.org>" [unknown]
# gpg: aka "Mark Brown <broonie@kernel.org>" [unknown]
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>" [unknown]
# gpg: aka "Mark Brown <broonie@linaro.org>" [unknown]
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 3F25 68AA C269 98F9 E813 A1C5 C3F4 36CA 30F5 D8EB
# Subkey fingerprint: ADE6 68AA 6757 18B5 9FE2 9FEA 24D6 8B72 5D54 87D0
PTR_ERR(NULL) is success. Normally when a function returns both NULL
and error pointers, it means that NULL is not a error.
But, rsnd_dmaen_request_channel() returns NULL if requested resource
was failed.
Let's return -EIO if rsnd_dmaen_request_channel() was failed on
rsnd_dmaen_nolock_start().
This patch fixes commit edce5c496c ("ASoC: rsnd: Request/Release DMA
channel eachtime")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current rsnd driver has rsnd_mod_id() which returns mod ID,
and it returns -1 if mod was NULL.
In the same time, this driver has rsnd_mod_name() which returns mod
name, and it returns "unknown" if mod or mod->ops was NULL.
Basically these "mod" never be NULL, but the reason why rsnd driver
has such behavior is that DMA path finder is assuming memory as
"mod == NULL".
Thus, current DMA path debug code prints like below.
Here "unknown[-1]" means it was memory.
...
rcar_sound ec500000.sound: unknown[-1] from
rcar_sound ec500000.sound: src[0] to
rcar_sound ec500000.sound: ctu[2]
rcar_sound ec500000.sound: mix[0]
rcar_sound ec500000.sound: dvc[0]
rcar_sound ec500000.sound: ssi[0]
rcar_sound ec500000.sound: audmac[0] unknown[-1] -> src[0]
...
1st issue is that it is confusable for user.
2nd issue is rsnd driver has something like below code.
mask |= 1 << rsnd_mod_id(mod);
Because of this kind of code, some statically code checker will
reports "Shifting by a negative value is undefined behaviour".
But this "mod" never be NULL, thus negative shift never happen.
To avoid these issues, this patch adds new dummy "mem" to
indicate memory, and use it to indicate debug information,
and, remove unneeded "NULL mod" behavior from rsnd_mod_id() and
rsnd_mod_name().
The debug information will be like below by this patch
...
rcar_sound ec500000.sound: mem[0] from
rcar_sound ec500000.sound: src[0] to
rcar_sound ec500000.sound: ctu[2]
rcar_sound ec500000.sound: mix[0]
rcar_sound ec500000.sound: dvc[0]
rcar_sound ec500000.sound: ssi[0]
rcar_sound ec500000.sound: audmac[0] mem[0] -> src[0]
...
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI parent mod might be NULL. ssi_parent_mod() needs to care
about it. Otherwise, it uses negative shift.
This patch fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When stop case, it was Playback, it need to check all data were
completely sent. But in Capture case, it might not receive data
anymore. SSISR::DIRQ check is not need for Capture case.
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Let's use more common style to checking running/working
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_unprepare() is checking parameter by IS_ERR_OR_NULL().
clk NULL check is not needed on rsnd_mod_quit()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have rsnd_io_to_mod() macro. Let's use it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ADG inputs clock from CLK{A,B,C,I} and outputs clock from
CLKOUT{0,1,2,3} which is selected by BRG{A,B}.
Now, ADG is assuming BRGA is for 44100Hz related clocks,
BRGB is for 48000Hz related clocks.
Clock related debug is very difficult/confusable.
This patch cleanups clock related debug info.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current CTU/MIX/DVC are directly using rsnd_kctrl_cfg_m/s to control
val etc, but it is difficult to read/understand.
And there was no uniformity in access method.
This patch adds new rsnd_kctrl_xxx() and implements uniformed access
method.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the of_device_get_match_data() helper instead of open coding.
Note that when used with DT, there's always a valid match.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Both DVC/MIX have Volume Ramp Control. This patch supprts MIX
Volume Ramp. One note is that main purpose of MIX Volume Ramp
is to reduce noise, thus, MIX Ramp range is very few if you
compare to DVC Volume Ramp (DVC = 5bit, MIX = 4bit).
You can use MIX Volume Ranp like below
amixer set "MIX Ramp Up Rate" "0.125 dB/1 step"
amixer set "MIX Ramp Down Rate" "0.125 dB/1 step"
amixer set "MIX Ramp" on
aplay xxx.wav &
amixer set "MIX",0 80% // DAI0 Volume Down
amixer set "MIX",1 100% // DAI1 Volume Up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC is supporting Volume Ramp Rate, and MIX has Volume Ramp
but not yet supported. To support MIX Volume Ramp, we want to
share Rate List since DVC/MIX are using almost same list.
This patch move DVC specific Volume Ramp Rate List to core.c.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Same CTU might be used few times if system/platform is using MIX.
For example below case.
DAI0 playback = <&src0 &ctu02 &mix0 &dvc0 &ssi0>;
DAI1 playback = <&src2 &ctu03 &mix0 &dvc0 &ssi0>;
This case, ALSA will have CTU,0 and CTU,1 kcontrol interfaces,
but these are same CTU. This is confusing.
This patch adds new flags and avoid such case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Same DVC might be used few times if system/platform is using MIX.
For example below case.
DAI0 playback = <&src0 &ctu02 &mix0 &dvc0 &ssi0>;
DAI1 playback = <&src2 &ctu03 &mix0 &dvc0 &ssi0>;
This case, ALSA will have DVC,0 and DVC,1 kcontrol interfaces,
but these are same DVC. This is confusing.
This patch adds new flags and avoid such case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI is using rsnd_ssi_flags_xxx() macro to control flags.
But it is useful macro not only for SSI. This patch replace it
to more generic rsnd_flags_xxx().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current device tree representation of the R-Car SSI assumes that they
are numbered consecutively, starting from 0. Alas, this is not the case
with the R8A77995 (D3) SoC which SSI1/SSI2 aren't present. In order to
keep the existing device trees working, I'm suggesting to use a disabled
node for SSI0/SSI1. Teach the SSI probe to just skip disabled nodes.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car sound DMA will be used from SSI/SRC.
dma.c doesn't alloc DMA handler in .probe timing, because we don't
know what kind of DMA transfer will be used then.
Thus, SSI/SRC have *rsnd_mod for DMA. rsnd_dma_attach() will allocate
it and attach it to system.
It will be PIO mode if it can't alloc DMA handler.
In case of MIX is used, rsnd_dma_attach() will be called twice from SSI.
To avoid duplicate allocation, current rsnd_dma_attach() is checking
allocated DMA handler. This DMA related operation is a little bit
difficult to understand.
This patch adds new rsnd_dma_alloc() and separates allocation and attach
for readable code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ADG driver is over-writing flags. This patch fixes it.
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make this const as it is only stored in the ops field of a
snd_soc_dai_link structure, which is const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make these const as they are only passed as the 2nd argument to the
function snd_soc_set_runtime_hwparams, which is const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_pcm_ops are not supposed to change at runtime. All functions
working with snd_pcm_ops provided by <sound/soc.h> work with
const snd_pcm_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make these const as they are either passed as the 2nd argument to
the function devm_snd_soc_register_platform or snd_soc_register_platform,
and the arguments are of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each module's dai callback function availability is controlled
by mod->status. For example "always called", "call once".
In .probe/.remove case, it needs to be called always, because
.probe will call xxx_attach() function on .probe, especially
if platform is using MIXer.
For example, below case, MIX0/DVC0/SSI0 needs to be called twice.
playback = <&src0 &ctu02 &mix0 &dvc0 &ssi0>;
playback = <&src2 &ctu03 &mix0 &dvc0 &ssi0>;
But in this case, SSI0 will call request_irq() twice.
This patch add new RSND_SSI_PROBED flag and control it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_ssi_mode_flags() is not useful. This patch adds
new rsnd_ssi_flags_has/add() macro for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 701172dca1 ("ASoC: rsnd: don't use devm_request_irq() for SSI")
exchanged devm_request_irq() to request_irq() for SSI, because SSI will
fallback into PIO mode if DMA doesn't work.
But, because of it, PIO mode needed to call free_irq() when removing,
not only DMA mode.
This patch call free_irq() both PIO/DMA. Otherwise, rsnd IRQ handler
will be increased if user tried many unbind/bind.
Fixes: 701172dca1 ("ASoC: rsnd: don't use devm_request_irq() for SSI")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 1f8754d4da ("ASoC: rsnd: don't call free_irq() on
Parent SSI") fixed Parent SSI duplicate free_irq().
But on Renesas Sound, not only Parent SSI but also Multi SSI
have same issue.
This patch avoid duplicate free_irq() if it was not pure SSI.
Fixes: 1f8754d4da ("ASoC: rsnd: don't call free_irq() on Parent SSI")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car Gen3 sound device can use TDM 16ch, but its usage is very
limited. It is not yet supported.
Let's remove unexpected/unsupported channel settings for now.
This patch makes xx_ADINR register settings sanity without
runtime check.
R-Car Gen3 datasheet
40.4.7 Note on Usage of the SSIU Module
When an SSIU module is used in "TDM-16ch mode",
only the transfer with the external memory is available.
Reported-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of SSI0 playback, SSI1 capture, SSI0 might be shared for
clock output if clock master mode.
Current rsnd driver had been assumed that SSI clock contiguous
output which is needed for SSI parent needs SSICR::EN (SSI module
enable) bit.
But, this bit controls data input/output, not for clock.
Clock contiguous output needs SSICR : FORCE, SCKD, SWSD,
and SSIWSR : CONT. Not SSICR : EN.
Because of this wrong assumption, and insufficient control, on current
code, for example, if it starts SSI0(playback) -> SSI1(capture) order,
SSI0 SSICR::EN bit will temporarily be 0.
It causes playback side underrun error. This is bug.
We can reproduce this issue with SSI+SRC (without DVC), and capture
during playback operation.
This patch fixup current (wrong) assumption, and control SSICR::EN bit
correctly.
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For example SSI0/SSI1 case, SSI1 can share pin with SSI0.
And then, SSI1 needs SSI0's clock.
This clock controlling is very picky and difficult to understand
in current code.
This patch adds new rsnd_ssi_can_output_clk() macro,
the code will be more understandable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it the same style as other functions
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ADG is registering fixed rate clock for audio_clkout, but it had not
been unregister clock when removing.
Salvator-X board is using ak4613 driver now, and it supports
hw_constraints from commit 907cd8809e ("ASoC: ak4613: add
hw_constraint rule for Sampling Rate").
And this calculation is using input clk. This ak4613 input clock is
ADG clkout on Salvator-X.
Because ADG had not been unregister clkout when unbinding, it receives
fixed rate clk register error when re-binding.
Thus, ak4613 can't get correct input clock, and hw_constraints will be
failed after re-binding.
This means Salvator-X board can't use sound after unbind/bind.
This patch solves this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver has snd_pcm_ops::open and snd_soc_dai_ops::startup,
but, these are called from soc_pcm_open in same time.
This patch merge these into rsnd_soc_dai_startup()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd kctrl is using both .private_value (for rsnd_kctrl_cfg)
and .private_data (for rsnd_mod) on snd_kcontrol.
But only 1 private data (= rsnd_kctrl_cfg) can be enough if it has
rsnd_mod pointer.
This patch doesn't use private_value.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit b047e1cce8 ("ASoC: ac97: Support multi-platform AC'97")
modified hac_soc_platform_probe(), but "int ret" was missed.
This patch adds missing "int ret", otherwise, we will get
linux/sound/soc/sh/hac.c: In function 'hac_soc_platform_probe':
linux/sound/soc/sh/hac.c:318: error: 'ret' undeclared (first use in this function)
linux/sound/soc/sh/hac.c:318: error: (Each undeclared identifier is reported only once
linux/sound/soc/sh/hac.c:318: error: for each function it appears in.)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove unnecessary static on local variable ops.
Such variable is initialized before being used,
on every execution path throughout the function.
The static has no benefit and, removing it reduces
the code size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see the difference in the code size. Also,
there is a significant difference in the bss segment. This log is the
output of the size command, before and after the code change:
before:
text data bss dec hex filename
3211 680 64 3955 f73 sound/soc/sh/rcar/ssiu.o
after:
text data bss dec hex filename
3207 592 0 3799 ed7 sound/soc/sh/rcar/ssiu.o
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
for_each_child_of_node performs an of_node_get on each iteration, so a
jump out of the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e,e1;
identifier l;
@@
for_each_child_of_node(e1,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? goto l;
)
...
}
...
l: ... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This dev_pm_ops structure is only stored in the pm field of a
device_driver structure. This field is declared const, so
dev_pm_ops structures that have this property can be declared
as const also.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The big news with this release is the of-graph card, this provides a
replacement for simple-card that is much more flexibile and scalable,
allowing many more systems to use a generic sound card than was possible
before:
- The of-graph card, finally merged after a long and dedicated effort
by Morimoto-san.
- New widget types intended mainly for use with DSPs.
- New drivers for Allwinner V3s SoCs, Ensonic ES8316, several classes
of x86 machine, Rockchip PDM controllers, STM32 I2S and S/PDIF
controllers and ZTE AUD96P22 CODECs.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAllaa7wTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0MhRB/0cIuUi/SmMSGz7cNKdDDArdpxHUV0U
dJb6qqhXCKeDQcx/34b1m+BnZpeT9au4Nt8HxOlLRbumcnuesYqfeBeZvuJhsC4I
q3e8e+idQlOp3+WM+snUXhWM4P/UsA9H4BaV1jvYSQW/C9WhfuLxsOraRiebLH7u
WJkmfeVjpzHHWzfDtpWJLHVroRLLMbOaz0e0Pw8/R1dfof0u27zKknqHOUcwRg0N
4+IWvKn3p59VE6eM6QUmruMZZCCfn2Hv5RygWf3LaHVlhA28BZi0dyMMSSSzVG6o
Im1Wm5z0dmmTfQKdNDU3PPBEKG6amTqF+2uuXOsq1I7vuiT+akHZbgWW
=F5BP
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.13
The big news with this release is the of-graph card, this provides a
replacement for simple-card that is much more flexibile and scalable,
allowing many more systems to use a generic sound card than was possible
before:
- The of-graph card, finally merged after a long and dedicated effort
by Morimoto-san.
- New widget types intended mainly for use with DSPs.
- New drivers for Allwinner V3s SoCs, Ensonic ES8316, several classes
of x86 machine, Rockchip PDM controllers, STM32 I2S and S/PDIF
controllers and ZTE AUD96P22 CODECs.
Don't populate the arrays path and cmd_case on the stack but make
them static const. Makes the object code smaller:
Before:
text data bss dec hex filename
2673 624 0 3297 ce1 sound/soc/sh/rcar/cmd.o
After:
text data bss dec hex filename
2398 768 0 3166 c5e sound/soc/sh/rcar/cmd.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
8172 920 0 9092 2384 sound/soc/sh/rcar/core.o
File size After adding 'const':
text data bss dec hex filename
8364 728 0 9092 2384 sound/soc/sh/rcar/core.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes this WARNING
sound/soc/sh/rcar/ssi.c:285:5-14: WARNING: Unsigned expression\
compared with zero: main_rate < 0
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver is assuming that all Sampling rate and
channles are possible to use, but these are depends on inputed clock
and SSI connection situation.
For example, if it is using 1 SSI, enabled TDM mode and has 12288000
input clock, 2ch output can support until 192000Hz, but 6ch output can
support until 64000Hz, 8ch can support 48000Hz.
To control these situation correctly, it needs to support
hw_constraints / refine feature.
To support such feature, this patch adds new
rsnd_soc_hw_rule/constraint() which adds hw rule of Channel and
Sampling Rate.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver is assuming that all Sampling rate and
channles are possible to use, but these are depends on inputed clock
and SSI connection situation.
For example, if it is using 1 SSI, enabled TDM mode and has 12288000
input clock, 2ch output can support until 192000Hz, but 6ch output can
support until 64000Hz, 8ch can support 48000Hz.
To control these situation correctly, it needs to support
hw_constraints / refine feature.
To support such feature, this patch adds new rsnd_ssi_clk_query().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver is assuming that all Sampling rate and
channles are possible to use, but these are depends on inputed clock
and SSI connection situation.
For example, if it is using 1 SSI, enabled TDM mode and has 12288000
input clock, 2ch output can support until 192000Hz, but 6ch output can
support until 64000Hz, 8ch can support 48000Hz.
To control these situation correctly, it needs to support
hw_constraints / refine feature.
To support such feature, it needs SSI clock query feature, and it needs
ADG clock query feature. Current ADG has rsnd_adg_ssi_clk_try_start()
and it is doing similar things, but it try to setup ADG register in
same time. This is not needed.
This patch adds new rsnd_adg_clk_query() and separates query feature
and register setting feature in adg.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver has slots and slots_num in
struct rsnd_dai, but these are very un-understandable naming
(It had named from TDM slots).
In this driver, the "slots" means total usable channels, and
"stot_num" means SSI lane number if Multi SSI was used.
To more understandable code, this patch renames "slots" to
"max_channels", and "slots_num" to "ssi_lane", and replaces related
functions name.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dai_call() macro is using "priv" inside.
Thus, if caller function doesn't have "priv" related operation, strange
phenomenon occur which code is using "priv", but compiler indicates
"unused variable 'priv'".
>From code point of view, it is not problem, but it is very confusable.
This patch removes "priv" from rsnd_dai_call() macro, and adds "priv"
on caller function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SRC/DVC/CTU adds kctrl for each device,
and SRC can adjust its sampling rate during playback,
thus, this feature should be enabled only *during* playback.
This patch controls it more clearly
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas Sound device *Hardware* L/R and Linux *Software* L/R are
inverted. Because of this background, it needs to convert L/R.
Then, DVC needs *Hardware* L/R, and Linux needs *Software* L/R.
Because Playback/Capture needs different timing, and there is no
explanation about it on source code / git log, this patch adds it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is sharing pointer related code between
PIO / DMA. But, it is used only PIO mode now, no longer needed.
This patch cleanup these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver updates pointer when DMA transfer was finished
in DMA transfer mode. But PulseAudio requests more accurate
pointer update when timer mode.
This patch consider about DMA transfer residue and update more
accurate pointer.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_ssi_non_ops is never used. Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare snd_kcontrol_new structures as const as they are only passed an
argument to the function snd_ctl_new1. This argument is of type const,
so snd_kcontrol_new structures having this property can be made const.
Done using Coccinelle:
@r disable optional_qualifier@
identifier x;
position p;
@@
static struct snd_kcontrol_new x@p={...};
@ok@
identifier r.x;
position p;
@@
snd_ctl_new1(&x@p,...)
@bad@
position p != {r.p,ok.p};
identifier r.x;
@@
x@p
@depends on !bad disable optional_qualifier@
identifier r.x;
@@
+const
struct snd_kcontrol_new x;
Cross compiled these files:
sound/aoa/codecs/tas.c - powerpc
sound/mips/{hal2.c/sgio2audio.c} - mips
sound/ppc/{awacs.c/beep.c/tumbler.c} - powerpc
sound/soc/sh/siu_dai.c - sh
Could not find an architecture to compile sound/sh/aica.c.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
commit 25165f79ad ("ASoC: rsnd: enable clock-frequency for both
44.1kHz/48kHz") supported both 44.1kHz/48kHz for AUDIO_CLKOUTx,
but it didn't care its parent clock name.
This patch fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 90431eb49b ("ASoC: rsnd: don't use PDTA bit for 24bit on SSI")
fixups 24bit mode data alignment, but PIO was not cared.
This patch fixes PIO mode 24bit data alignment
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car Gen3 can output HDMI sound if SSIU/SSI are connected to
R-Car built-in HDMI device (R-Car Gen3 built-in HDMI device will be
controlled by DRM/KMS driver).
If SSIx was connected to HDMI0/1 on DT, SSI driver will detect it
automatically by this patch.
Note is that now Renesas R-Car sound driver is assuming that it is
using OF-graph base simple card for HDMI sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To enable OF-graph base DT on rsnd driver, and to keep compatible
previous normal sound card style, it need to support both
"rcar_sound,dai" and "ports" (or "port") on DT.
This patch parses both style.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To enable OF-graph base DT on rsnd driver, and to keep compatible
previous normal sound card style, it need to support both
"rcar_sound,dai" and "ports" (or "port") on DT.
This patch modify rsnd_dai_of_node() to parse
"rcar_sound,dai" and "ports" (or "port") as phase 1. It can detect
graph base style, but do nothing at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If SSI uses shared pin, some SSI will be used as parent SSI.
Then, normal SSI's remove and Parent SSI's remove
(these are same SSI) will be called when unbind or remove timing.
In this case, free_irq() will be called twice.
This patch solve this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SSI uses PDTA bit which indicates data that Input/Output
data are Right-Aligned. But, 24bit sound should be Left-Aligned
in this HW. Because Linux is using Right-Aligned data, and HW uses
Left-Aligned data, current 24bit data is missing lower 8bit.
To fix this issue, this patch removes PDTA bit, and shift 8bit
in necessary module
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With gcc 4.1.2:
sound/soc/sh/fsi.c:304: warning: ‘fsi_stream_is_play’ declared inline after being called
sound/soc/sh/fsi.c:304: warning: previous declaration of ‘fsi_stream_is_play’ was here
Move fsi_stream_is_play() up to fix this, removing the need for a
forward declaration as well.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Without this patch, gcc 4.9.x says
sound/soc/sh/rcar/cmd.c: In function 'rsnd_cmd_init':
sound/soc/sh/rcar/cmd.c:85:14: warning: array subscript is below array\
bounds [-Warray-bounds]
data = path[rsnd_mod_id(src)] |
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dai_call() is counting the called number of start/stop functions.
nolock_stop should be called if nolock_start was failed.
Otherwise, nolock_start doesn't called in 2nd play.
This patch solved this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit d7f298197a
("ASoC: rcar: fixup of_clk_add_provider() usage for multi clkout")
added adg->clkout[i] = ERR_PTR(-ENOENT),
but, adg->clkout[i] are assumed NULL or clk pointer.
This patch fix it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clkout-lr-asynchronous is AUDIO_CLKOUT related property, thus, it
should be handled by rsnd_adg_get_clkout().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Before, src.c cares SRC and SSIU, but now SSIU is cared by ssiu.c by
commit c7f69ab536 ("ASoC: rsnd: use mod base common method on SSIU").
This patch removes mismatched explanation for SRC/SSIU from src.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
25165f79ad
("ASoC: rsnd: enable clock-frequency for both 44.1kHz/48kHz")
supports both 44.1kHz/48kHz clock-frequency settings for ADG
which will be used for AUDIO_OLKOUTn.
But some board doesn't need it, thus, it is not mandatory.
But, above patch didn't care about the case of "clock-frequency" DT
property was not present.
This patch ignores ADG settings if AUDIO_OLKOUTn was not used.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
[Kuninori: tidyup not to break non AUDIO_OLKOUTn case]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current clock-frequency allows only 1 clock, but ADG can
handle both 44.1kHz/48kHz base clocks. This patch enables these.
On Salvator-X board, AUDIO_CLKOUT which is generated by ADG
is connected to ak4613 MCKI, and it should be synchronized with
LRCK. Thus, we need both 44.1kHz/48kHz base clock-frequency.
Otherwise, either one sounds strange in high frequency sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_mod_make_sure() will be used any situation,
thus, under DEBUG is not realistic.
This patch move it to non DEBUG area
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using rsnd_kctrl_new_m/s/e function,
but the differences are very few.
This patch merge these rsnd_kctrl_new_m/s/e into rsnd_kctrl_new
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current src->convert_rate will be set on .hw_param, and
be reset on .quit timing.
But, .hw_param will not be called again if user did Ctrl-Z + fg.
It should be reset on initial of .hw_param to keep its value.
Here, ctu.c already do this.
This patch solves this issue, other wise, MIXed sound will be
strange if user did like below.
> aplay -D plughw:0,0 sound_44100.wav &
> aplay -D plughw:0,1 sound_96000.wav
> Ctrl-Z
> fg # 96kHz will be played as 44.1kHz
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
adg is calling of_clk_add_provider() when probe time,
thus, remove should call of_clk_del_provider(), it doesn't now.
This patch fix this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current adg is calling of_clk_add_povider() multiple times,
but it is not correct usage. This patch fixup its parameter
and call it once.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rcar driver is trying to remove kctrl when remove time.
But, 1) rcar driver can't/shouldn't remove before removing sound
card driver, 2) sound card driver will call snd_ctl_dev_free()
and removes all kctrls by snd_ctl_remove().
Thus, rsnd_kctrl_remove() is not necessary. Current implementation
will get Oops when removing rcar driver after sound card.
This patch fix this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car Datasheet is indicating "SSICR.CKDV = 000 is invalid when
SSIWSR.WS_MODE = 1 or SSIWSR.CONT = 1".
Current driver will set CONT, thus, we shouldn't use CKDV = 000.
This patch fixup it.
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 2a3af642eb20("ASoC: rcar: clear DE bit only in PDMACHCR...")
added rsnd_dmapp_bset(), but it used copy-paste. Thus, it had
unnecessary "volatile", and had below warning on x86.
This patch fix it.
sound/soc/sh/rcar/dma.c: In function 'rsnd_dmapp_bset':
>> sound/soc/sh/rcar/dma.c:463:21: warning: passing argument 1 of \
'ioread32' discards 'volatile' qualifier from pointer target \
type [-Wdiscarded-qualifiers]
u32 val = ioread32(addr);
^~~~
In file included from arch/x86/include/asm/io.h:203:0,
from arch/x86/include/asm/realmode.h:5,
from arch/x86/include/asm/acpi.h:33,
from arch/x86/include/asm/fixmap.h:19,
from arch/x86/include/asm/apic.h:10,
from arch/x86/include/asm/smp.h:12,
from include/linux/smp.h:59,
from include/linux/topology.h:33,
from include/linux/gfp.h:8,
from include/linux/idr.h:16,
from include/linux/kernfs.h:14,
from include/linux/sysfs.h:15,
from include/linux/kobject.h:21,
from include/linux/of.h:21,
from include/linux/of_dma.h:16,
from sound/soc/sh/rcar/dma.c:12:
include/asm-generic/iomap.h:31:21: note: expected 'void *' \
but argument is of type 'volatile void *'
extern unsigned int ioread32(void __iomem *);
^~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car datasheet indicates "Clear DE in PDMACHCR" for transfer stop,
but current code clears all bits in PDMACHCR.
Because of this, DE bit might never been cleared,
and it causes CMD overflow. This patch fixes this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the problem that the missing value of the route path
setting table and incorrect values are set in the CMD_ROUTE_SELECT
register.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
[Kuninori: shared data on MIX and non-MIX case]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI8 is is sharing pin with SSI7, and nothing to do for SSI_MODEx.
It is special pin and it needs special settings whole system,
but we can't confirm it, because we never have SSI8 available board.
This patch fixup SSI_MODEx settings error for SSI8 on connection test,
but should be confirmed behavior on real board in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, this function cannot fail for the ADG case. Still, let's
apply defensive programming techniques to make sure we fail gracefully
whenever rsnd_mod_init() gets extended with another failure case.
Reported by Coverity (CID 1397893).
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Coverity reported (CID 1397992) this self-assignment. I think the code
stays readable even with the assignments removed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sync convert rate settings should be availabled *after* Playing.
Thus, src->sync should be reset first of init function.
Otherwise, it will set remaining settings when it start playing.
This patch fixes it. Thanks to Yokoyama-san
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 5f222a292 ("ASoC: rsnd: use for_each_rsnd_mod_xxx() ...")
modifies rsnd_dai_call() to use for_each_rsnd_mod_arrays().
Current rsnd is incrementing iterator in rsnd_mod_next(),
but the iterator will indicate +1 position in for_each loop in
this case. Incremental position should be inside for()
Reported-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 5f222a292 ("ASoC: rsnd: use for_each_rsnd_mod_xxx() ...")
modifies rsnd_dai_call() to use for_each_rsnd_mod_arrays().
Current rsnd is incrementing iterator in rsnd_mod_next(),
but the iterator will indicate +1 position in for_each loop in
this case. Incremental position should be inside for()
Reported-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On an error, snd_ctl_add already free's kctrl, so calling snd_ctl_free_one
to free it again leads to a double free error. Fix this by removing
the extraneous snd_ctl_free_one call.
Issue found using static analysis with CoverityScan, CID 1372908
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver setups BRGCKR/BRRA/BRRB when .probe timing.
But it breaks sound after Suspend/Resume. These should be setups
every start timing.
This patch is tested on R-Car Gen3 Salvator-X board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver enables ADG clock when .probe timing,
but it breaks sound after Suspend/Resume. These should be setups
every suspend/resume timing too.
This patch is tested on R-Car Gen3 Salvator-X board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ssi->usrcnt will be updated on snd_soc_dai_ops::trigger,
but snd_pcm_ops::hw_params will be called *before* it.
Thus, ssi->usrcnt is still 0 when 1st call.
rsnd_ssi_hw_params() needs to check its called count, this means
trigger should be if (ssi->usrcnt) instead of if (ssi->usrcnt > 1).
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSIU was controlled by SSI before, but
commit c7f69ab53("ASoC: rsnd: use mod base common method on SSIU")
separated it into ssiu.c
But, it didn't care about rsnd_get_dalign() for judging SSI_BUSIF_DALIGN
register value which changes the stream data order.
This function will be called from cmd/src/ssiu now, but current code
still cares ssi, not ssiu.
This patch fix it up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
IOMMU needs DMA mapping function to use it. One solution is that
we can use DMA mapped dev on snd_pcm_lib_preallocate_pages_for_all()
for SNDRV_DMA_TYPE_DEV. But pcm_new and dma map timing are mismatched.
Thus, this patch uses SNDRV_DMA_TYPE_CONTINUOUS for pcm_new,
and use dma_sync_single_for_xxx() for each transfer.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas Sound driver requests DMA channel when .probe timing,
and release it when .remove timing. And use DMA on .start/.stop
But, Audio DMAC power ON was handled when request timing (= .probe),
and power OFF was when release timing (= .remove).
This means Audio DMAC power is always ON during driver was enabled.
The best choice to solve this issue is that DMAEngine side handle
this. But current DMAEngine API design can't solve atmic/non-atmic
context issue for power ON/OFF. So next better choice is sound
driver request/release DMA channel each time. This patch do it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current register name of "SSICKR" was came from R-Car Gen1
which is very old style. It is called as "BRGCKR" on R-Car Gen2/Gen3.
Let's rename it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SRC (= Sampling Rate Converter) is supporting
SYNC mode and ASYNC mode. Current src.c cares SRC if FIN != FOUT.
Here, SYNC mode will be used for tweak, so it will be used
even FIN = FOUT. This patch enables SRC sync in such situation
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Tested-by: Yuichi Takagi <yuichi.takagi.uh@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound SSIU has SSI_SYS_STATUS register whick will
be changed if over/under run was occurred.
Current rsnd driver is handling over/under run error on SSI/SRC,
but doesn't on SSIU.
HW guys can't guarantee correct behavior if it already had error bit
on status register when it start.
Thus, it should be cleared every start timing. This patch do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SCU_SYS_STATUSx is the register that writing 1 initializes the bit,
and writing 0 is ignored. So, it should use rsnd_mod_write()
instead of rsnd_mod_bset(), otherwise all bit will be cleared.
Thanks Shimoda-san
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car Gen1 didn't have SSIU IP, and it was part of SRU.
In Gen2, SSIU was created and it has original register.
Let's cleanup rsnd_reg for SSIU, because this driver
doesn't support Gen1 SRU any more.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Gen1 support had been removed. "Gen2 only" comment is
no longer needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver is completely depends on CONFIG_OF
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas Sound driver requests DMA channel when .probe timing,
and release it when .remove timing. And use DMA on .start/.stop
But, Audio DMAC power ON was handled when request timing (= .probe),
and power OFF was when release timing (= .remove).
This means Audio DMAC power is always ON during driver was enabled.
To fixup this issue, it should request/release DMA channel on each
playback/recorde timing.
But, DMA channel request/release function uses mutex lock inside.
This means it will breaks current spinlock's interrupt protect.
To solve this issue, DMA channel request/release function needs to
be called from non-spinlock area. This patch adds its callback.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_dmaen_start() is calling of_node_put() for np,
but it is not needed if it goes through this loop.
This patch tidyup it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA mod is now connected to stream via rsnd_dai_connect().
This means DMA mod can use .remove for its clearance.
rsnd_dma_detach() is no longer needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI will use DMA mode, and migh be fallback to PIO mode.
Using devm_request_irq() makes its operation more complex when
it fallbacks to PIO mode.
Let's use manual request_irq()/free_irq()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas Sound driver is based on DeviceTree, and no one is
using this driver from non DT. Non-DT support is no longer needed.
Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now, we have for_each_rsnd_mod(), let's use it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using too complex macro for for-loop of each mod.
rsnd_dai_call() is especially defined as very complex macro.
It is easier to read just a little bit by using for_each_rsnd_mod_xxx()
and new rsnd_status_update()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using too complex macro for for-loop of each mod.
In order to simplify this issue, this patch adds new rsnd_mod_next()
which is non-macro.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 1a5658c213 ("ASoC: rsnd: count .probe/.remove for
rsnd_mod_call()") solved multi-resource-free issue, by putting
.probe/.remove under count control. But,it breaks sound mixing case
(if it was used under DPCM). In such case, it uses MIXn/DVCn/SSIn,
and these should be always probed.
This patch reverted above patch, and solved the same issue by
modifing _rsnd_kctrl_remove() function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds SNDRV_PCM_TRIGGER_SUSPEND/RESUME.
Otherwise, it breaks rsnd driver internal start/stop counter
when suspend/resume. This issue was reported/tested by Hiep
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsrc-card which is using DPCM feature was created for Renesas sound.
But not only Renesas, but many SoC can use this driver, because
it is based on simple-card driver.
To use it as more open driver, rsrc-card will be renamed to
simple-scu-card. In order to easy patch review, as 3rd step,
this patch moves rsrc-card driver to generic folder.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsrc-card which is using DPCM feature was created for Renesas sound.
But not only Renesas, but many SoC can use this driver, because
it is based on simple-card driver.
To use it as more open driver, rsrc-card will be renamed to
simple-scu-card. In order to easy patch review, as 2nd step,
this patch adds new compatible "simple-scu-audio-card";
rcar-card used specific property, not "simple-audio-card",
but it should be now. Actually, rsrc-card is upstreamed driver,
but noone is using it on upstream. The user is only local,
and it is only me. Thus, there is no compatible break by this patch.
This patch uses "simple-audio-card" prefix.
And it removes rcar-card specifix compatible too.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsrc-card which is using DPCM feature was created for Renesas sound.
But not only Renesas, but many SoC can use this driver, because
it is based on simple-card driver.
To use it as more open driver, rsrc-card will be renamed to
simple-scu-card. In order to easy patch review, as 1st step,
this patch renames "rsrc" function prefix to "asoc_simple".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsrc-card has board specific compatible (= lager/koelsh), but these were
created as 1st prototype, and it is used in my test environment only.
Now normal user can use generic compatible (= renesas,rsrc-card).
Removing these board specific compatible doesn't breake compatibility.
This patch remove these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We get 1 warning about global functions without a declaration
in the ASoC sub-system when building with W=1:
sound/soc/sh/rcar/core.c:113:6: warning: no previous prototype for 'rsnd_mod_make_sure' [-Wmissing-prototypes]
void rsnd_mod_make_sure(struct rsnd_mod *mod, enum rsnd_mod_type type)
In this case, the function 'rsnd_mod_make_sure' is declared in rsnd.h file,
but it only valid if the macro DEBUG is claimed.
so the implementation of function 'rsnd_mod_make_sure' need be
held by macro DEBUG.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2;
statement S2,S1;
@@
- if (of_get_property(e1,e2,NULL))
+ if (of_property_read_bool(e1,e2))
S1 else S2
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the calculation accuracy degradation of SRCm_IFSVR
register value.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When building with 'make W=1', we get a harmless warning about
slightly incorrect prototypes in the rcar audio driver:
sound/soc/sh/rcar/gen.c: In function 'rsnd_gen2_probe':
sound/soc/sh/rcar/gen.c:209:2: error: 'static' is not at beginning of declaration [-Werror=old-style-declaration]
This changes the 'const static' to 'static const' as it should be.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
AUDIO-CLKOUTn can asynchronizes with L/R clock.
AUDIO-CLKOUTn synchronizes with L/R clock is now default behavior.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSICKR (Gen2) / BRGCKR (Gen3) 31bit mask should be opened,
because BRGB (= for 48kHz) might select it.
Special thanks Yokoyama-san
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current device tree representation of the R-Car Sample Rate Converters
(SRC) assumes that they are numbered consecutively, starting from 0. Alas,
this is not the case with the R8A7794 SoC where SRC0 isn't present. In
order to keep the existing device trees working, I'm suggesting to use a
disabled node for SRC0. Teach the SRC probe to just skip disabled nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_dmapp_get_id() returns 0xFF as error code if system used
strange connection. It will be used as PDMACHCRn.SRS, but 0xFF is
prohibited number.
In order not to use prohibited number, this patch indicates error message
and returns 0x00 (same as SSI00) in error case.
Special thanks to Dung-san.
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_mod_call is counting its calling count to avoid unbalanced
function pair calling for error cases (ex init <-> quit).
SSI parent is now controlled as "mod" on current rsnd driver. Because of
this reason, SSI .remove function will be called twice if it was used as
SSI parent when user tried unbind. But probe/remove pair were not
counted. This patch counts probe/remove functions to avoid it.
Special thans Hiep
Reported-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound driver user needs to read its datasheet when create DT.
But it is difficult to understand, because it has many modules
(SRC/CTU/MIX/DVC/SSIU/SSI/AudioDMAC/AudioDMACperiperi),
and many features (Asynchronous/Synchronous mode on SRC, CTU matrix,
DVC volume settings feature, Multi-SSI/TDM-SSI, etc).
This patch adds simplified explanation to help setting/understanding.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CMD.out should use same as SRC.out for TIMSEL settings,
but it cares Playback case only. This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC has Sync/Async mode, and it can't use Sync mode when Capture
with CMD. In Async mode, it needs to care about in/out SRC rate
for settings, but current driver supporting Playback case only.
This patch supports Capture case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC will convert rate, and then, CMD and SSI want to know its
rate (= SRC.in / SRC.out) for each purpose.
Current driver is supporting only Playback, but SRC+Capture support
needs more flexibility.
This patch adds rsnd_src_get_in/out_rate() for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_enable_sync_convert() is for checking, not for setting.
In order to avoid confusion, this patch renamed it to
rsnd_src_sync_is_enabled()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To reduce confusion, SRC uses "mod" instead of "src"
as function parameter
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC sync mode needs to control its clock (= for in/out). 1st but codec
side clock
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It can't use SRC Synchronous convert when Capture if it uses CMD,
because no one provide out side clocks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds CTU (= Channel Transfer Unit) support on
Renesas R-Car sound driver.
It can Down/Up mixing and splitter. You need to check R-Car datasheet
especially CTUn_CPMDR/CTUn_SV0xR/CTUn_SV1xR/CTUn_SV2xR/CTUn_SV3xR
for setting parameter.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SSI is supporting Normal SSI/Multi mode SSI/TDM mode SSI
and its behavior is based on input channels.
This input channel might be converted by CTU,
and SSI needs to be Multi SSI mode / TDM SSI mode if 6ch input
EX) 6ch input, CTU for 2ch, playback
6ch 6ch 2ch 2ch 2ch 2ch
-> SRC -> CTU -> MIX -> DVC -> SSIU -> SSI
EX) 6ch input, no CTU, Multi SSI, playback
6ch 6ch 6ch 6ch 6ch 2ch
-> SRC -> CTU -> MIX -> DVC -> SSIU -> SSI0/SSI1/SSI2
Current driver is using rsnd_get_adinr_chan() / rsnd_get_slot_width()
for this purpose, but it is complicated enough without meaning.
This patch adds new rsnd_runtime_channel_xxx() which is caring
CTU/Multi SSI.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Renesas R-Car sound CTU (= Channel Transfer Unit)
very basic support, but not yet enough feature at this point.
Because CTU support needs more complex channel function for
each modules.
To avoid complex patch reviewing, this patch picked up very basic
part only.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound device has CTU (= Channel Transfer Unit), and
sound card needs its support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some R-Car sound requests picky register access which needs *force*
register write.
Some status register needs to set 1 to clear status, but we might
read 1 from its register. In such case, current regmap does nothing
and driver will be forever loop
To reduce code complexity, this patch uses regmap _force_
function for all register access.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd supports multi SSI (maximum 4 SSI for 8ch),
and, it should determine whether using each SSI or not in runtime.
All SSIs are not used even if there are 4 SSI in case of stereo.
Current driver setups un-used SSI in such case. It is no problem,
but not needed. This patch judges it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd supports multi SSI (maximum 4 SSI for 8ch),
and, it should determine whether using each SSI or not in runtime.
Current judgement is vague, and had broken by
c308abe45e2("ASoC: rsnd: rsnd_ssi_is_multi_slave() macro uses
rsnd_ssi_multi_slaves()")
This patch makes clean it, and solve this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
prepare for runtime judging for SSI work
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Parent SSI is needed if it is PIN sharing and clock master,
otherwise, not needed. But, whether clockk master is judged on
.set_fmt, thus, it can't call rsnd_ssi_parent_attach() on .probe.
Now, .pcm_new will be called after .set_fmt, so this patch reuses it
at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI want to have SSIWSR settings and SSICR settings without EN bit
when init, and SSICR EN bit only when start timing.
Otherwise, SSI output signal might be unstable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit b5b442abd9 ("ASoC: rsnd: add .irq callback") added .irq callback
but SSI DMA is missing it. This patch adds it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit b5b442abd9 ("ASoC: rsnd: add .irq callback")
added .irq support, and it cares both parent SSI and normal SSI.
But it should care only normal SSI. Otherwise SSI might be
forever loop if SSI is used as both parent SSI and normal SSI
(= 2 users), and if under/over run error happen. Because irq disable
do nothing in such case. This patch solve this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To reduce confusion, SSI uses "mod" instead of "ssi"
as function parameter
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC_ROUTE_MODE0 determines whether to use SRC.
Thus, it should be setup before SRC_SRCIR.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The channels number is not only for DVC. Let's rename it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
b4c83b171 ("ASoC: rsnd: add Multi channel support") added
Multi channel support, and current rsnd_ssi_is_multi_slave()'s check
method is !SSI equals SSIM1/2/3. But, SSI parent also hit to this macro.
Because of this reason, some stream which needs SSI parent clock
can't work correctly. This patch uses rsnd_ssi_multi_slaves() to
solve this issue. This issue was reported by Dung.
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver has .init/.start/.stop/.quit callbacks,
and it needs many IPs (SRC/CTU/MUX/DVC/CMD/SSIU/SSI).
Because of these relationship, it might get unnecessary
error IRQ when start/stop.
This patch adds new .irq callback and control IRQ enable/disable
timing to avoid it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car sound needs recovery (= restart) when under/over run
error occurred, and current driver tries it on under/over run error
handler automatically. But this recovery should be handled by userland,
not kernel. This patch stops XRUN when under/over run error occur, and
will leave the recovery of HW in userland.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit b761bf272b ("ASoC: rsnd: disable SRC.out only when stop timing")
disabled SRC.out/in in different timing, but was based on
picky HW information. Now, we have confirmed that we can disable
both in the same time. This patch do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current CTU settings was rough. This patch makes it match to datasheet.
But do nothing at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI/SRC will try to attach DMAC as Audio-DMAC or Audio-DMAC-periperi.
It is fixed IP, but will be attached to each streams as different module
in case of MUX (= multi sound path will be merged).
This patch solves this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI will be used as normal SSI or as clock parent SSI. Therefor,
rsnd driver wants to control SSI and parent SSI separately. Otherwise it
can't use Playback/Capture in the same time.
And it has been done by c2dc47d5cf("ASoC: rsnd: rsnd_dai_stream has each
mod's status insted of rsnd_mod") before.
OTOH, rsnd driver doesn't want to control CTU/MUX/DVC/SSIU/SSI in
separately. Otherwise, these will be re-initialized during playing if
MUX merges 2 sounds.
Because of these picky reasons, this patch re-defines status on each mod,
and add new parent_ssi_status on rsnd_dai_stream.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To select CMD data patch, it should use correct SRC from each stream
in MUX case. But current code is selecting SRC from fixed stream.
This patch solves this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_cmd_init() overwrites "io" which will be used end of this
function. This patch solved this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CTU/MUX/DVC/SSIU/SSI/Audio-DMAC-periperi might be used under multipath.
So, probe()/remove() need to be called multiple times.
This patch allows it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If system uses CTU/MUX, CTU/MUX/DVC will try to connect same CMD to
system, but it is not error in this case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If system uses CTU/MUX, and if probe error happened, it will try to
call rsnd_dai_call(remove, ...). Then, MUX/DVC/SSIU/SSI might be called
without calling rsnd_dai_call(probe, ...). Then, each mod status might
be un-matched. It doesn't call un-matched remove function by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_mod_call() tries to call each IP's relevant function. But it is
difficult to understand which function returned error.
This patch adds debug message for this purpose
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ADG doesn't use rsnd_mod_init(), but this limitation is no
longer necessary. Let's use common rsnd_mod_init()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bitwise OR has higher precedence than ?: so the val2 was always set
to 0x2.
Fixes: b4c83b1715 ('ASoC: rsnd: add Multi channel support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Field usrcnt is unsigned so it cannot be lesser than zero.
The patch fixes the check, moves it to the beginning of the function
and changes return value to -EIO in case of usercnt error.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Multi channel support on Renesas R-Car sound.
This patch is tested on Salvator-X board, but it can't use
Multi channel, because supported format is different between
codec chip and R-Car.
Thus, it was tested on board which doesn't mount codec chip,
with oscilloscope.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using complex macro to parse DAI connection.
This patch adds new rsnd_parse_connect_common() and replace current
macro to it.
This is prepare for multi channel support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TDM will use 6 or 8 slots on 1 SSI, and Multi channel will use
6 or 8 slots on few SSI (each SSI uses 2 slots).
Thus, this adds new slot control functions which can be prepare
for Multi channel support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_get_slot_rdai() returns total slots (it returns 6 if total 6
channels) , and rsnd_get_slot_extend() returns extended SSI width
(it returns 8 if total 6 channels). This will be used on SSI multi
channel support too (It will return 2 if total 6 channels with 3 SSI).
But, it is using confusable naming.
This patch changes rsnd_get_slot_rdai() -> rsnd_get_slot(),
rsnd_get_slot_extend() -> rsnd_get_slot_width()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver is using rsnd_get_slot_runtime(), but
it is same as runtime->channels. This patch removes
rsnd_get_slot_runtime()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SSI/SSIU are using rsnd_get_slot_runtime() to check TDM,
but using rsnd_get_slot_extend() is more sane.
This patch fix it up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It can't output corrent dma name *before* rsnd_mod_init().
It goes to *after* rsnd_mod_init() by this patch
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound driver has rsnd_get_adinr_bit/chan() functions.
It is assuming _bit() returns ADINR :: OTBL,
and _chan() returns ADINR :: CHNUM.
Current _bit() returns both OTBL and CHNUM. This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSIU should be controlled after SSI. This patch fix up it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsrc-card is DPCM supported version of simple-card. Thus it has similar
DT format. OTOH, snd_soc_dai_link requests cpu/codec, but one of them
will be snd-soc-dummy in DPCM case, and DPCM requests frontend/backend
dai_link. This means it might have multi backend/codec.
And, SND_SOC_DAIFMT_xxx is based on "codec". Because of these
difference, current rsrc card can't detect correct dai_fmt.
This patch detect correct dai fmt from 1st "codec".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
1efb53a220 ("ASoC: simple-card: Remove support for setting differing
DAI formats") removed set_fmt support from simple-card.
rsrc-card follows same style, because it is based on simple-card.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound driver will use tdm slot on TDM Multi Mode support.
This patch enables tdm slot on rsrc card driver on DT.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We use ret as the return value from the rsnd_mix_probe() but if there
are no child nodes and no errors then we will never initialize ret leading
to build warnings. Ensure ret is initialized before we iterate over the
child nodes to avoid this.
Signed-off-by: Mark Brown <broonie@kernel.org>
We use ret as the return value from the rsnd_dvc_probe() but if there
are no child nodes and no errors then we will never initialize ret leading
to build warnings. Ensure ret is initialized before we iterate over the
child nodes to avoid this.
Signed-off-by: Mark Brown <broonie@kernel.org>
We use ret as the return value from the rsnd_ctu_probe() but if there
are no child nodes and no errors then we will never initialize ret leading
to build warnings. Ensure ret is initialized before we iterate over the
child nodes to avoid this.
Signed-off-by: Mark Brown <broonie@kernel.org>
L/R channel data has been treated as inverted on R-Car sound 16bit mode,
Thus, 4689032b1("ASoC: rsnd: tidyup data align position") tidyuped data
align position. But it couldn't care about capture case. This patch
cares both playback/capture
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSICR::SWSP bit controls WS signal low/high, but in case of TDM
it is inverted. This patch solves this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds missing check of snd_soc_of_get_dai_name().
It might not be able to use sound card, because it might returns
-EPROBE_DEFER.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drv pointer should be "base + offset" instead of
"current + offset". This patch fixup this issue, otherwise
third and subsequent pointer will be broken
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car can out TDM by
1) 6ch x 1 DAI as TDM Extend Mode
2) 2ch x 4 x 1 DAI as TDM split Mode
3) 2ch x 3 DAI or
2ch x 4 DAI as TDM Multichannel Mode
This patch adds 1) TDM Extend Mode. Because of HW design,
this 6ch data will be outputed via 8ch data width.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current DVC is assuming that the sound is always stereo.
This patch makes it more flexible
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SSI is assuming that the sound is always stereo. But, SSI needs
to calculate its frequency when master mode. Then This frequency depends
on each SSI's slots, and TDM mode (= TDM Extend Mode, TDM split Mode,
TDM Multichannel Mode).
This patch enables to use non-stereo sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It will have TDM settings on SSIWSR. Actually, we would like to set
it on rsnd_ssi_config_init(), but we can't. Because SSI might be used
as clock master (It doesn't need to call rsnd_ssi_config_init() when
clock master mode).
This patch adds new ssi->wsr and set it on rsnd_ssi_start().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to enhance code readability, this patch adds
rsnd_ssi_config_init() and moves SSICR register settings to it.
This is prepare patch for TDM support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC_BUSIF_MODE has both IN/OUT register. Current src driver sets
IN register only. This patch sets missing OUT register.
IN/OUT register are using default setting, so, there is no
HW effect.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC/SRC/SSIU needs ADINR::CHNUM settings too. This patch adds
these missing value.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
adg.c is used from ssi/src/cmd. Thus don't use confusable *mod here.
This patch rename it to ssi_mod/src_mod/cmd_mod
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_ssi_record_error() should recorde error, but it clears error too.
this patch fixes up semantic of rsnd_ssi_record_error that it records
error but doesn't clear error.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_src_error_record() should recorde error, but it clears error too.
this patch fixes up semantic of rsnd_src_error_record that it records
error but doesn't clear error.
And this patch renames
rsnd_src_error_clear() to rsnd_src_status_clear()
rsnd_src_error_record() to rsnd_src_record_error()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is indicating how to use regmap debug method
on gen.c comment area.
regmap debug method indicates address and value, but rsnd driver is
using too many IPs (SSI/SSIU/SRC/CTU/MIX/DVC/CMD), and address.
Thus, we would like to know more useful information for debugging.
This patch indicates address name for debugging.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After a recent cleanup, the soc_card variable became unused
and now produces a warning:
soc/sh/rcar/core.c: In function '__rsnd_kctrl_new':
soc/sh/rcar/core.c:801:23: warning: unused variable 'soc_card' [-Wunused-variable]
This removes the variable.
Fixes: 1a497983a5 ("ASoC: Change the PCM runtime array to a list")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As this driver can now be compiled for ARM64, we get a new warning
as a result of passing a DMA filter data pointer through an 'int':
sound/soc/sh/fsi.c: In function 'fsi_dma_probe':
sound/soc/sh/fsi.c:1372:24: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
shdma_chan_filter, (void *)io->dma_id,
We already know that we only need the legacy filter function on
arch/sh, so we can hide the legacy DMA interface function
behind an #ifdef. This has the other advantage of no longer
depending on the shdma_chan_filter function to be visible.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
64bit compiler indicates this without this patch
linux/sound/soc/sh/rcar/core.c: In function 'rsnd_probe':
linux/sound/soc/sh/rcar/core.c:1002:16: warning: cast from pointer to\
integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the number of DAI links is statically defined by the machine
driver at build time using an array. This makes it difficult to shrink/
grow the number of DAI links at runtime in order to reflect any changes
in topology.
We can change the DAI link array in the core to a list so that PCMs and
FE DAI links can be added and deleted at runtime to reflect changes in
use case and DSP topology. The machine driver can still register DAI links
as an array.
As the 1st step, this patch change the PCM runtime array to a list. A new
PCM runtime is added to the list when a DAI link is bound successfully.
Later patches will further implement the DAI link list.
More:
- define snd_soc_new/free_pcm_runtime() to create/free a runtime.
- define soc_add_pcm_runtime() to add a runtime to the rtd list.
- define soc_remove_pcm_runtimes() to clean up the runtime list.
- traverse the rtd list to probe the link components and dais.
- Add a field "num" to PCM runtime struct, used to specify the device
number when creating the pcm device, and for a soc card to access
its dai_props array.
- The following 3rd party machine/platform drivers iterate the rtd list
to check the runtimes:
sound/soc/intel/atom/sst-mfld-platform-pcm.c
sound/soc/intel/boards/cht_bsw_rt5645.c
sound/soc/intel/boards/cht_bsw_rt5672.c
sound/soc/intel/boards/cht_bsw_max98090_ti.c
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver requests struct platform_device on
probe/remove for each modules. But driver can get it by
rsnd_priv_to_pdev(). This patch removes unnecessary parameter
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No board is using Renesas sound driver via platform boot now.
This means all user is using DT boot. Platform boot support is
no longer needed. But, it strongly depends on platform boot style.
Now, platform boot style was removed from driver.
This is cleanup patch, and remove pointless struct rcar_snd_info
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No board is using Renesas sound driver via platform boot now.
This means all user is using DT boot. Platform boot support is
no longer needed. But, it strongly depends on platform boot style.
Now, platform boot style was removed from driver.
This is cleanup patch, and remove pointless struct rsnd_of_data
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No board is using Renesas sound driver via platform boot now.
This means all user is using DT boot. Platform boot support is
no longer needed. But, it strongly depends on platform boot style.
This patch removes platform boot support from gen.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No board is using Renesas sound driver via platform boot now.
This means all user is using DT boot. Platform boot support is
no longer needed. But, it strongly depends on platform boot style.
This patch removes platform boot support from dvc.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No board is using Renesas sound driver via platform boot now.
This means all user is using DT boot. Platform boot support is
no longer needed. But, it strongly depends on platform boot style.
This patch removes platform boot support from mix.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No board is using Renesas sound driver via platform boot now.
This means all user is using DT boot. Platform boot support is
no longer needed. But, it strongly depends on platform boot style.
This patch removes platform boot support from ctu.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuninori Morimoto
Kees Cook
Geert Uytterhoeven
Mark Brown
Arnd Bergmann
Nikita Yushchenko
Jiada Wang
Greg Kroah-Hartman
Bhumika Goyal
Markus Elfring
Arvind Yadav
Gustavo A. R. Silva
Julia Lawall
Takashi Iwai
Colin Ian King
Geert Uytterhoeven
Marek Vasut
kbuild test robot
Hiroyuki Yokoyama
Wolfram Sang
Baoyou Xie
Sergei Shtylyov
Stephen Boyd
Dan Carpenter
Andrzej Hajda
Mengdong Lin