raid5_mergeable_bvec tries to ensure that raid5 never sees a read request
that does not fit within just one chunk. However as we must always accept
a single-page read, that is not always possible.
So when "in_chunk_boundary" fails, it might be unusual, but it is not a
problem and printing a message every time is a bad idea.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a GFP_KERNEL allocation is attempted in md while the mddev_lock is held,
it is possible for a deadlock to eventuate.
This happens if the array was marked 'clean', and the memalloc triggers a
write-out to the md device.
For the writeout to succeed, the array must be marked 'dirty', and that
requires getting the mddev_lock.
So, before attempting a GFP_KERNEL allocation while holding the lock, make
sure the array is marked 'dirty' (unless it is currently read-only).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow noflush suspend/resume of device-mapper device only for the case
where the device size is unchanged.
Otherwise, dm-multipath devices can stall when resumed if noflush was used
when suspending them, all paths have failed and queue_if_no_path is set.
Explanation:
1. Something is doing fsync() on the block dev,
holding inode->i_sem
2. The fsync write is blocked by all-paths-down and queue_if_no_path
3. Someone requests to suspend the dm device with noflush.
Pending writes are left in queue.
4. In the middle of dm_resume(), __bind() tries to get
inode->i_sem to do __set_size() and waits forever.
'noflush suspend' is a new device-mapper feature introduced in
early 2.6.20. So I hope the fix being included before 2.6.20 is
released.
Example of reproducer:
1. Create a multipath device by dmsetup
2. Fail all paths during mkfs
3. Do dmsetup suspend --noflush and load new map with healthy paths
4. Do dmsetup resume
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In most cases we check the size of the bitmap file before reading data from
it. However when reading the superblock, we always read the first PAGE_SIZE
bytes, which might not always be appropriate. So limit that read to the size
of the file if appropriate.
Also, we get the count of available bytes wrong in one place, so that too can
read past the end of the file.
Cc: "yang yin" <yinyang801120@gmail.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we sometimes step the array events count backwards (when
transitioning dirty->clean where nothing else interesting has happened - so
that we don't need to write to spares all the time), it is possible for the
event count to return to zero, which is potentially confusing and triggers and
MD_BUG.
We could possibly remove the MD_BUG, but is just as easy, and probably safer,
to make sure we never return to zero.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When 'repair' finds a block that is different one the various parts of the
mirror. it is meant to write a chosen good version to the others. However it
currently writes out the original data to each. The memcpy to make all the
data the same is missing.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
md raidX make_request functions strip off the BIO_RW_SYNC flag, thus
introducing additional latency.
Fixing this in raid1 and raid10 seems to be straightforward enough.
For our particular usage case in DRBD, passing this flag improved some
initialization time from ~5 minutes to ~5 seconds.
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Lars Ellenberg <lars@linbit.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While developing more functionality in mdadm I found some bugs in md...
- When we remove a device from an inactive array (write 'remove' to
the 'state' sysfs file - see 'state_store') would should not
update the superblock information - as we may not have
read and processed it all properly yet.
- initialise all raid_disk entries to '-1' else the 'slot sysfs file
will claim '0' for all devices in an array before the array is
started.
- all '\n' not to be present at the end of words written to
sysfs files
- when we use SET_ARRAY_INFO to set the md metadata version,
set the flag to say that there is persistant metadata.
- allow GET_BITMAP_FILE to be called on an array that hasn't
been started yet.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Thanks Jens for alerting me to this.
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <raziebe@gmail.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As CBC is the default chaining method for cryptoloop, we should select
it from cryptoloop to ease the transition. Spotted by Rene Herman.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix few bugs that meant that:
- superblocks weren't alway written at exactly the right time (this
could show up if the array was not written to - writting to the array
causes lots of superblock updates and so hides these errors).
- restarting device recovery after a clean shutdown (version-1 metadata
only) didn't work as intended (or at all).
1/ Ensure superblock is updated when a new device is added.
2/ Remove an inappropriate test on MD_RECOVERY_SYNC in md_do_sync.
The body of this if takes one of two branches depending on whether
MD_RECOVERY_SYNC is set, so testing it in the clause of the if
is wrong.
3/ Flag superblock for updating after a resync/recovery finishes.
4/ If we find the neeed to restart a recovery in the middle (version-1
metadata only) make sure a full recovery (not just as guided by
bitmaps) does get done.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently raid5 depends on clearing the BIO_UPTODATE flag to signal an error
to higher levels. While this should be sufficient, it is safer to explicitly
set the error code as well - less room for confusion.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are some vestiges of old code that was used for bypassing the stripe
cache on reads in raid5.c. This was never updated after the change from
buffer_heads to bios, but was left as a reminder.
That functionality has nowe been implemented in a completely different way, so
the old code can go.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The autorun code is only used if this module is built into the static
kernel image. Adjust #ifdefs accordingly.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
stripe_to_pdidx finds the index of the parity disk for a given stripe. It
assumes raid5 in that it uses "disks-1" to determine the number of data disks.
This is incorrect for raid6 but fortunately the two usages cancel each other
out. The only way that 'data_disks' affects the calculation of pd_idx in
raid5_compute_sector is when it is divided into the sector number. But as
that sector number is calculated by multiplying in the wrong value of
'data_disks' the division produces the right value.
So it is innocuous but needs to be fixed.
Also change the calculation of raid_disks in compute_blocknr to make it
more obviously correct (it seems at first to always use disks-1 too).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Call the chunk_aligned_read where appropriate.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If a bypass-the-cache read fails, we simply try again through the cache. If
it fails again it will trigger normal recovery precedures.
update 1:
From: NeilBrown <neilb@suse.de>
1/
chunk_aligned_read and retry_aligned_read assume that
data_disks == raid_disks - 1
which is not true for raid6.
So when an aligned read request bypasses the cache, we can get the wrong data.
2/ The cloned bio is being used-after-free in raid5_align_endio
(to test BIO_UPTODATE).
3/ We forgot to add rdev->data_offset when submitting
a bio for aligned-read
4/ clone_bio calls blk_recount_segments and then we change bi_bdev,
so we need to invalidate the segment counts.
5/ We don't de-reference the rdev when the read completes.
This means we need to record the rdev to so it is still
available in the end_io routine. Fortunately
bi_next in the original bio is unused at this point so
we can stuff it in there.
6/ We leak a cloned bio if the target rdev is not usable.
From: NeilBrown <neilb@suse.de>
update 2:
1/ When aligned requests fail (read error) they need to be retried
via the normal method (stripe cache). As we cannot be sure that
we can process a single read in one go (we may not be able to
allocate all the stripes needed) we store a bio-being-retried
and a list of bioes-that-still-need-to-be-retried.
When find a bio that needs to be retried, we should add it to
the list, not to single-bio...
2/ We were never incrementing 'scnt' when resubmitting failed
aligned requests.
[akpm@osdl.org: build fix]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This will encourage read request to be on only one device, so we will often be
able to bypass the cache for read requests.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
An md array can be stopped leaving all the setting still in place, or it can
torn down and destroyed. set_capacity and other change notifications only
happen in the latter case, but should happen in both.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reset sync_search on resume. The effect is to retry syncing all out-of-sync
regions when a mirror is resumed, including ones that previously failed.
Signed-off-by: Jonathan E Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The complete_resync_work function only provides the ability to change an
out-of-sync region to in-sync. This patch enhances the function to allow us
to change the status from in-sync to out-of-sync as well, something that is
needed when a mirror write to one of the devices or an initial resync on a
given region fails.
Signed-off-by: Jonathan E Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the code that releases memory used by a snapshot into a separate function.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement the pushback feature for the multipath target.
The pushback request is used when:
1) there are no valid paths;
2) queue_if_no_path was set;
3) a suspend is being issued with the DMF_NOFLUSH_SUSPENDING flag.
Otherwise bios are returned to applications with -EIO.
To check whether queue_if_no_path is specified or not, you need to check
both queue_if_no_path and saved_queue_if_no_path, because presuspend saves
the original queue_if_no_path value to saved_queue_if_no_path.
The check for 1 already exists in both map_io() and do_end_io().
So this patch adds __must_push_back() to check 2 and 3.
Test results:
See the test results in the preceding patch.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In device-mapper I/O is sometimes queued within targets for later processing.
For example the multipath target can be configured to store I/O when no paths
are available instead of returning it -EIO.
This patch allows the device-mapper core to instruct a target to transfer the
contents of any such in-target queue back into the core. This frees up the
resources used by the target so the core can replace that target with an
alternative one and then resend the I/O to it. Without this patch the only
way to change the target in such circumstances involves returning the I/O with
an error back to the filesystem/application. In the multipath case, this
patch will let us add new paths for existing I/O to try after all the existing
paths have failed.
DMF_NOFLUSH_SUSPENDING
----------------------
If the DM_NOFLUSH_FLAG ioctl option is specified at suspend time, the
DMF_NOFLUSH_SUSPENDING flag is set in md->flags during dm_suspend(). It
is always cleared before dm_suspend() returns.
The flag must be visible while the target is flushing pending I/Os so it
is set before presuspend where the flush starts and unset after the wait
for md->pending where the flush ends.
Target drivers can check this flag by calling dm_noflush_suspending().
DM_MAPIO_REQUEUE / DM_ENDIO_REQUEUE
-----------------------------------
A target's map() function can now return DM_MAPIO_REQUEUE to request the
device mapper core queue the bio.
Similarly, a target's end_io() function can return DM_ENDIO_REQUEUE to request
the same. This has been labelled 'pushback'.
The __map_bio() and clone_endio() functions in the core treat these return
values as errors and call dec_pending() to end the I/O.
dec_pending
-----------
dec_pending() saves the pushback request in struct dm_io->error. Once all
the split clones have ended, dec_pending() will put the original bio on
the md->pushback list. Note that this supercedes any I/O errors.
It is possible for the suspend with DM_NOFLUSH_FLAG to be aborted while
in progress (e.g. by user interrupt). dec_pending() checks for this and
returns -EIO if it happened.
pushdback list and pushback_lock
--------------------------------
The bio is queued on md->pushback temporarily in dec_pending(), and after
all pending I/Os return, md->pushback is merged into md->deferred in
dm_suspend() for re-issuing at resume time.
md->pushback_lock protects md->pushback.
The lock should be held with irq disabled because dec_pending() can be
called from interrupt context.
Queueing bios to md->pushback in dec_pending() must be done atomically
with the check for DMF_NOFLUSH_SUSPENDING flag. So md->pushback_lock is
held when checking the flag. Otherwise dec_pending() may queue a bio to
md->pushback after the interrupted dm_suspend() flushes md->pushback.
Then the bio would be left in md->pushback.
Flag setting in dm_suspend() can be done without md->pushback_lock because
the flag is checked only after presuspend and the set value is already
made visible via the target's presuspend function.
The flag can be checked without md->pushback_lock (e.g. the first part of
the dec_pending() or target drivers), because the flag is checked again
with md->pushback_lock held when the bio is really queued to md->pushback
as described above. So even if the flag is cleared after the lockless
checkings, the bio isn't left in md->pushback but returned to applications
with -EIO.
Other notes on the current patch
--------------------------------
- md->pushback is added to the struct mapped_device instead of using
md->deferred directly because md->io_lock which protects md->deferred is
rw_semaphore and can't be used in interrupt context like dec_pending(),
and md->io_lock protects the DMF_BLOCK_IO flag of md->flags too.
- Don't issue lock_fs() in dm_suspend() if the DM_NOFLUSH_FLAG
ioctl option is specified, because I/Os generated by lock_fs() would be
pushed back and never return if there were no valid devices.
- If an error occurs in dm_suspend() after the DMF_NOFLUSH_SUSPENDING
flag is set, md->pushback must be flushed because I/Os may be queued to
the list already. (flush_and_out label in dm_suspend())
Test results
------------
I have tested using multipath target with the next patch.
The following tests are for regression/compatibility:
- I/Os succeed when valid paths exist;
- I/Os fail when there are no valid paths and queue_if_no_path is not
set;
- I/Os are queued in the multipath target when there are no valid paths and
queue_if_no_path is set;
- The queued I/Os above fail when suspend is issued without the
DM_NOFLUSH_FLAG ioctl option. I/Os spanning 2 multipath targets also
fail.
The following tests are for the normal code path of new pushback feature:
- Queued I/Os in the multipath target are flushed from the target
but don't return when suspend is issued with the DM_NOFLUSH_FLAG
ioctl option;
- The I/Os above are queued in the multipath target again when
resume is issued without path recovery;
- The I/Os above succeed when resume is issued after path recovery
or table load;
- Queued I/Os in the multipath target succeed when resume is issued
with the DM_NOFLUSH_FLAG ioctl option after table load. I/Os
spanning 2 multipath targets also succeed.
The following tests are for the error paths of the new pushback feature:
- When the bdget_disk() fails in dm_suspend(), the
DMF_NOFLUSH_SUSPENDING flag is cleared and I/Os already queued to the
pushback list are flushed properly.
- When suspend with the DM_NOFLUSH_FLAG ioctl option is interrupted,
o I/Os which had already been queued to the pushback list
at the time don't return, and are re-issued at resume time;
o I/Os which hadn't been returned at the time return with EIO.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide a dm ioctl option to request noflush suspending. (See next patch for
what this is for.) As the interface is extended, the version number is
incremented.
Other than accepting the new option through the interface, There is no change
to existing behaviour.
Test results:
Confirmed the option is given from user-space correctly.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update existing targets to use the new symbols for return values from target
map and end_io functions.
There is no effect on behaviour.
Test results:
Done build test without errors.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tighten the use of return values from the target map and end_io functions.
Values of 2 and above are now explictly reserved for future use. There are no
existing targets using such values.
The patch has no effect on existing behaviour.
o Reserve return values of 2 and above from target map functions.
Any positive value currently indicates "mapping complete", but all
existing drivers use the value 1. We now make that a requirement
so we can assign new meaning to higher values in future.
The new definition of return values from target map functions is:
< 0 : error
= 0 : The target will handle the io (DM_MAPIO_SUBMITTED).
= 1 : Mapping completed (DM_MAPIO_REMAPPED).
> 1 : Reserved (undefined). Previously this was the same as '= 1'.
o Reserve return values of 2 and above from target end_io functions
for similar reasons.
DM_ENDIO_INCOMPLETE is introduced for a return value of 1.
Test results:
I have tested by using the multipath target.
I/Os succeed when valid paths exist.
I/Os are queued in the multipath target when there are no valid paths and
queue_if_no_path is set.
I/Os fail when there are no valid paths and queue_if_no_path is not set.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the interface of dm_suspend() so that we can pass several options
without increasing the number of parameters. The existing 'do_lockfs' integer
parameter is replaced by a flag DM_SUSPEND_LOCKFS_FLAG.
There is no functional change to the code.
Test results:
I have tested 'dmsetup suspend' command with/without the '--nolockfs'
option and confirmed the do_lockfs value is correctly set.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The existing code allocates an extra slot in bi_io_vec[] and uses it to store
the region number.
This patch hides the extra slot from bio_add_page() so the region number can't
get overwritten.
Also remove a hard-coded SECTOR_SHIFT and fix a typo in a comment.
Signed-off-by: Heinz Mauelshagen <hjm@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Milan Broz <mbroz@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This facility provides three entry points:
ilog2() Log base 2 of unsigned long
ilog2_u32() Log base 2 of u32
ilog2_u64() Log base 2 of u64
These facilities can either be used inside functions on dynamic data:
int do_something(long q)
{
...;
y = ilog2(x)
...;
}
Or can be used to statically initialise global variables with constant values:
unsigned n = ilog2(27);
When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant. They treat negative numbers as
unsigned.
When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.
[akpm@osdl.org: MMC fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename DM's struct path to struct dm_path to prevent name collision between it
and struct path from fs/namei.c.
Signed-off-by: Josef "Jeff" Sipek <jsipek@cs.sunysb.edu>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Cc: <reiserfs-dev@namesys.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md_open takes ->reconfig_mutex which causes lockdep to complain. This
(normally) doesn't have deadlock potential as the possible conflict is with a
reconfig_mutex in a different device.
I say "normally" because if a loop were created in the array->member hierarchy
a deadlock could happen. However that causes bigger problems than a deadlock
and should be fixed independently.
So we flag the lock in md_open as a nested lock. This requires defining
mutex_lock_interruptible_nested.
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the old complex and crufty bd_mutex annotation.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move process freezing functions from include/linux/sched.h to freezer.h, so
that modifications to the freezer or the kernel configuration don't require
recompiling just about everything.
[akpm@osdl.org: fix ueagle driver]
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rather than stuffing integers into pointers with casts, let's use
a union.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
LRW-32-AES needs a certain IV. This IV should be provided dm-crypt.
The block cipher mode could, in principle generate the correct IV from
the plain IV, but I think that it is cleaner to supply the right IV
directly.
The sector -> narrow block calculation uses a shift for performance reasons.
This shift is computed in .ctr and stored in cc->iv_gen_private (as a void *).
Signed-off-by: Rik Snel <rsnel@cube.dyndns.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If there's a swap file on a software RAID, it should be possible to use this
file for saving the swsusp's suspend image. Also, this file should be
available to the memory management subsystem when memory is being freed before
the suspend image is created.
For the above reasons it seems that md_threads should not be frozen during the
suspend and the appended patch makes this happen, but then there is the
question if they don't cause any data to be written to disks after the suspend
image has been created, provided that all filesystems are frozen at that time.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I forgot to has the size-in-blocks to (loff_t) before shifting up to a
size-in-bytes.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It turns out that CHANGE is preferred to ONLINE/OFFLINE for various reasons
(not least of which being that udev understands it already).
So remove the recently added KOBJ_OFFLINE (no-one is likely to care anyway)
and change the ONLINE to a CHANGE event
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All device-mapper targets must complete outstanding I/O before suspending.
The mirror target generates I/O in its recovery phase and fails to wait for
it. It needs to be tracked so we can ensure that it has completed before we
suspend.
[akpm@osdl.org: cleanup]
Signed-off-by: Jonathan E Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <dm-devel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When adding paths to the round-robin path selector, their order gets inverted,
which is not desirable.
Fix by replacing list_add() with list_add_tail().
Signed-off-by: Jonathan E Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <dm-devel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the device is already suspended, just return the error and skip the code
that would incorrectly wipe md->suspended_bdev.
(This isn't currently a problem because existing code avoids calling this
function if the device is already suspended.)
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: <dm-devel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown
Jun'ichi Nomura
Lars Ellenberg
Herbert Xu
Jeff Garzik
Raz Ben-Jehuda(caro)
Adrian Bunk
Jonathan E Brassow
Milan Broz
Kiyoshi Ueda
Heinz Mauelshagen
David Howells
Josef Sipek
Josef "Jeff" Sipek
Peter Zijlstra
Linus Torvalds
Nigel Cunningham
Christoph Lameter
Rik Snel
Rafael J. Wysocki
Alasdair G Kergon