This patch adds better IPv6 failover support for bonding devices,
especially when in active-backup mode and there are only IPv6 addresses
configured, as reported by Alex Sidorenko.
- Creates a new file, net/drivers/bonding/bond_ipv6.c, for the
IPv6-specific routines. Both regular bonds and VLANs over bonds
are supported.
- Adds a new tunable, num_unsol_na, to limit the number of unsolicited
IPv6 Neighbor Advertisements that are sent on a failover event.
Default is 1.
- Creates two new IPv6 neighbor discovery functions:
ndisc_build_skb()
ndisc_send_skb()
These were required to support VLANs since we have to be able to
add the VLAN id to the skb since ndisc_send_na() and friends
shouldn't be asked to do this. These two routines are basically
__ndisc_send() split into two pieces, in a slightly different order.
- Updates Documentation/networking/bonding.txt and bumps the rev of bond
support to 3.4.0.
On failover, this new code will generate one packet:
- An unsolicited IPv6 Neighbor Advertisement, which helps the switch
learn that the address has moved to the new slave.
Testing has shown that sending just the NA results in pretty good
behavior when in active-back mode, I saw no lost ping packets for example.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A packet dequeued and stored as gso_skb in qdisc_peek_dequeued() should
be seen as part of the queue for sch->q.qlen queries until it's really
dequeued with qdisc_dequeue_peeked(), so qlen needs additional updating
in these functions. (Updating qstats.backlog shouldn't matter here.)
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have been tracking for a while a case where when the
network namespace exits the cleanup gets stck in an
endless precessess of:
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
It turns out that if you listen on a multicast address an unsubscribe
packet is sent when the network device goes down. If you shutdown
the network namespace without carefully cleaning up this can trigger
the unsubscribe packet to be sent over the loopback interface while
the network namespace is going down.
All of which is fine except when we drop the packet and forget to
free it leaking the skb and the dst entry attached to. As it
turns out the dst entry hold a reference to the idev which holds
the dev and keeps everything from being cleaned up. Yuck!
By fixing my earlier thinko and add the needed kfree_skb and everything
cleans up beautifully.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was recently hunting a bug that occurred in network namespace
cleanup. In looking at the code it became apparrent that we have
and will continue to have cases where if we have anything going
on in a network namespace there will be assumptions that the
loopback device is present. Things like sending igmp unsubscribe
messages when we bring down network devices invokes the routing
code which assumes that at least the loopback driver is present.
Therefore to avoid magic initcall ordering hackery that is hard
to follow and hard to get right insert a call to register the
loopback device directly from net_dev_init(). This guarantes
that the loopback device is the first device registered and
the last network device to go away.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When physical devices are inside of network namespace and that
network namespace terminates we can not make them go away. We
have to keep them and moving them to the initial network namespace
is the best we can do.
For virtual devices left in a network namespace that is exiting
we have no need to preserve them and we now have the infrastructure
that allows us to delete them. So delete virtual devices when we
exit a network namespace. Keeping the necessary user space clean up
after a network namespace exits much more tractable.
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed a contention on udp_memory_allocated on regular UDP applications.
While tcp_memory_allocated is seldom used, it appears each incoming UDP frame
is currently touching udp_memory_allocated when queued, and when received by
application.
One possible solution is to use sk_mem_reclaim_partial() instead of
sk_mem_reclaim(), so that we keep a small reserve (less than one page)
of memory for each UDP socket.
We did something very similar on TCP side in commit
9993e7d313
([TCP]: Do not purge sk_forward_alloc entirely in tcp_delack_timer())
A more complex solution would need to convert prot->memory_allocated to
use a percpu_counter with batches of 64 or 128 pages.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This inserts the required de-allocation routines for memory allocated
by feature negotiation in the socket destructors, replacing
dccp_feat_clean() in one instance.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides feature-negotiation initialisation for both DCCP sockets
and DCCP request_sockets, to support feature negotiation during
connection setup.
It also resolves a FIXME regarding the congestion control
initialisation.
Thanks to Wei Yongjun for help with the IPv6 side of this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds list initial fields and list management functions for the
new feature negotiation implementation.
Thanks to Arnaldo for suggestions and improvements.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
A lookup table for feature-negotiation information, extracted from RFC
4340/42, is provided by this patch. All currently known features can
be found in this table, along with their feature location, their
default value, and type.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares for the new and extended feature-negotiation
routines.
The following feature-negotiation data structures are provided:
* a container for the various (SP or NN) values,
* symbolic state names to track feature states,
* an entry struct which holds all current information together,
* elementary functions to fill in and process these structures.
Entry structs are arranged as FIFO for the following reason: RFC 4340
specifies that if multiple options of the same type are present, they
are processed in the order of their appearance in the packet; which
means that this order needs to be preserved in the local data
structure (the later insertion code also respects this order).
The struct list_head has been chosen for the following reasons: the most
frequent operations are
* add new entry at tail (when receiving Change or setting socket
options);
* delete entry (when Confirm has been received);
* deep copy of entire list (cloning from listening socket onto
request socket).
The NN value has been set to 64 bit, which is a currently sufficient
upper limit (Sequence Window feature has 48 bit).
Thanks to Arnaldo, who contributed the streamlined layout of the entry
struct.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: David S. Miller <davem@davemloft.net>
All these individual parsing functions never return an error,
so they can be void.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed duplicated #include <rdma/ib_verbs.h> in net/9p/trans_rdma.c
and #include <linux/thread_info.h> in net/socket.c
Signed-off-by: Jianjun Kong <jianjun@zeuux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I want to compile out proc_* and sysctl_* handlers totally and
stub them to NULL depending on config options, however usage of &
will prevent this, since taking adress of NULL pointer will break
compilation.
So, drop & in front of every ->proc_handler and every ->strategy
handler, it was never needed in fact.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only user of the net_device->last_rx field is bonding.
This patch adds a conditional update of last_rx to the bonding special
logic in skb_bond_should_drop, causing last_rx to only be updated when
the ARP monitor is running.
This frees network device drivers from the necessity of
updating last_rx, which can have cache line thrash issues.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gets about 1.25% back on tbench regression.
My change to NAPI for multiqueue support changed the time limit on
network receive processing. Under sustained loads like tbench, this
can cause the receiver to reschedule prematurely.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
put_dec_trunc prints the digits in reverse order and is reversed
inside number(). Continue using put_dec_trunc, but reverse each quad
in ip4_addr_string.
[Noticed by Julius Volz]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the 'supports_ipv6' scheduler flag since all schedulers now
support IPv6.
Signed-off-by: Julius Volz <julius.volz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 support to LBLC and LBLCR schedulers. These were the last
schedulers without IPv6 support, but we might want to keep the
supports_ipv6 flag in the case of future schedulers without IPv6
support.
Signed-off-by: Julius Volz <julius.volz@gmail.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the version to 3.95.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the BCM50610 to the list of phys supported by the
broadcom driver.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the expansion register access routines a little more
formal. They will be used by the following bcm50610 support patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds flow control support to Broadcom phys.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refines support for the 5785 device.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refines the phylib support in the tg3 driver. The patch does
the following things :
* Rename tg3_mdio_config() to tg3_mdio_config_5785(). The 5785 will be
the only device that will use it so the name might as well reflect
that.
* Fix a memory leak if mdiobus_register() fails.
* Add code to deal with phy device detection failures.
* Add code to correct the supported list of phy features based on the
MAC <=> PHY interface.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows WOL to be enabled for Broadcom phys under phylib
control. The only exception is the AC131, which has a completely
different register set.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 12dac0756d ("tg3: adapt tg3 to
use reworked PCI PM code") introduced the new PCI PM API to the tg3
driver. The patch was understandably conservative, so this patch
elaborates on that work.
The patch starts by creating a single point in tg3_set_power_state()
to decide whether or not to enable WOL. The rest of the code in
tg3_set_power_state() was then pivoted to use the result of this
decision.
The patch then makes sure the device is allowed to wakeup before
reporting whether or not WOL is currently enabled. The final hunks of
the patch consolidate where the WOL capability and WOL enabled flags
are set to a single location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, phylib reports appear with a eth%d prefix. Move the line
after register_netdev() and place it alongside the other informative
messages. Update nearby informative messages accordingly.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With older versions of the NVRAM format, the driver may mistakenly
determine that APE is enabled. Make sure this doesn't happen by
restricting the ENABLE_APE check to devices known to have more
recent NVRAM image formats.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reclaims the TG3_FLG3_5761_5784_AX_FIXES flag. It only
used twice in non-fast paths. This patch also consolidates some other
places where specific 5784 AX chip revisions can be generalized.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the __tg3_set_mac_addr() function earlier in the file
listing, to avoid a function prototype, and calls the function to
restore the LAA after a driver unload chip reset. With this code in
place, the administrator can wake the machine using the LAA.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DASH firmware runs on the APE side of the chip, but it requires a few MAC
to be programmed correctly.
When WOL is enabled and management firmware is disabled, incoming
packets are evaluated and discarded at the chip's rule processor.
When management firmware is enabled, the hardware must be informed that
there are agents further up the stack that still use the incoming
frames. Normally management firmware will configure the MAC correctly
on its own, but there can be cases where the setting could get clobbered
by the driver. The first hunk of this patch preserves this setting.
The second hunk of this patch wipes out the driver present signature of
the APE memory space. By doing so, the DASH firmware can assume
driver absent behavior.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the existing APE register mapping code with a call
to pci_ioremap_bar(). The code that maps the main device register space
did not undergo a similar change because the information derived from
the pci_resource_start() and pci_resource_len() is still used to
populate the (optional) mem_start and mem_end netdevice members.
Replace hardcoded constants where appropriate.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the 5761S chip variants.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since gso_skb is re-used for qdisc_peek_dequeued(), and this skb is
counted in the qdisc->q.qlen, it has to be kfreed during qdisc_reset()
when qlen is zeroed.
With help from David S. Miller <davem@davemloft.net>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 support to SH and DH schedulers. I hope this simple IPv6 address
hashing is good enough. The 128 bit are just XORed into 32 before hashing
them like an IPv4 address.
Signed-off-by: Julius Volz <julius.volz@gmail.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brian Haley
Jarek Poplawski
Eric W. Biederman
Eric Dumazet
Gerrit Renker
Alexey Dobriyan
David S. Miller
Stephen Hemminger
Jianjun Kong
Jay Vosburgh
Harvey Harrison
Julius Volz
Matt Carlson