Pull SG updates from Jens Axboe:
"This contains a set of scatter-gather related changes/fixes for 4.3:
- Add support for limited chaining of sg tables even for
architectures that do not set ARCH_HAS_SG_CHAIN. From Christoph.
- Add sg chain support to target_rd. From Christoph.
- Fixup open coded sg->page_link in crypto/omap-sham. From
Christoph.
- Fixup open coded crypto ->page_link manipulation. From Dan.
- Also from Dan, automated fixup of manual sg_unmark_end()
manipulations.
- Also from Dan, automated fixup of open coded sg_phys()
implementations.
- From Robert Jarzmik, addition of an sg table splitting helper that
drivers can use"
* 'for-4.3/sg' of git://git.kernel.dk/linux-block:
lib: scatterlist: add sg splitting function
scatterlist: use sg_phys()
crypto/omap-sham: remove an open coded access to ->page_link
scatterlist: remove open coded sg_unmark_end instances
crypto: replace scatterwalk_sg_chain with sg_chain
target/rd: always chain S/G list
scatterlist: allow limited chaining without ARCH_HAS_SG_CHAIN
Pull core block updates from Jens Axboe:
"This first core part of the block IO changes contains:
- Cleanup of the bio IO error signaling from Christoph. We used to
rely on the uptodate bit and passing around of an error, now we
store the error in the bio itself.
- Improvement of the above from myself, by shrinking the bio size
down again to fit in two cachelines on x86-64.
- Revert of the max_hw_sectors cap removal from a revision again,
from Jeff Moyer. This caused performance regressions in various
tests. Reinstate the limit, bump it to a more reasonable size
instead.
- Make /sys/block/<dev>/queue/discard_max_bytes writeable, by me.
Most devices have huge trim limits, which can cause nasty latencies
when deleting files. Enable the admin to configure the size down.
We will look into having a more sane default instead of UINT_MAX
sectors.
- Improvement of the SGP gaps logic from Keith Busch.
- Enable the block core to handle arbitrarily sized bios, which
enables a nice simplification of bio_add_page() (which is an IO hot
path). From Kent.
- Improvements to the partition io stats accounting, making it
faster. From Ming Lei.
- Also from Ming Lei, a basic fixup for overflow of the sysfs pending
file in blk-mq, as well as a fix for a blk-mq timeout race
condition.
- Ming Lin has been carrying Kents above mentioned patches forward
for a while, and testing them. Ming also did a few fixes around
that.
- Sasha Levin found and fixed a use-after-free problem introduced by
the bio->bi_error changes from Christoph.
- Small blk cgroup cleanup from Viresh Kumar"
* 'for-4.3/core' of git://git.kernel.dk/linux-block: (26 commits)
blk: Fix bio_io_vec index when checking bvec gaps
block: Replace SG_GAPS with new queue limits mask
block: bump BLK_DEF_MAX_SECTORS to 2560
Revert "block: remove artifical max_hw_sectors cap"
blk-mq: fix race between timeout and freeing request
blk-mq: fix buffer overflow when reading sysfs file of 'pending'
Documentation: update notes in biovecs about arbitrarily sized bios
block: remove bio_get_nr_vecs()
fs: use helper bio_add_page() instead of open coding on bi_io_vec
block: kill merge_bvec_fn() completely
md/raid5: get rid of bio_fits_rdev()
md/raid5: split bio for chunk_aligned_read
block: remove split code in blkdev_issue_{discard,write_same}
btrfs: remove bio splitting and merge_bvec_fn() calls
bcache: remove driver private bio splitting code
block: simplify bio_add_page()
block: make generic_make_request handle arbitrarily sized bios
blk-cgroup: Drop unlikely before IS_ERR(_OR_NULL)
block: don't access bio->bi_error after bio_put()
block: shrink struct bio down to 2 cache lines again
...
It appears to be what the rest of the kernel does, so let's do it too.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Very similar to how it went with local_sockaddr.
It was embedded in iscsi_login_stats so some changes there, and we needed
to copy in a sockaddr_storage comparison function. Hopefully the kernel
will get a standard one soon, our implementation makes the 3rd.
isert_set_conn_info() became much smaller.
IPV6_ADDRESS_SPACE define goes away, had to modify a call to in6_pton(),
can just use -1 since we are sure string is null-terminated.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is a more natural format that lets us format it with the appropriate
printk specifier as needed.
This also lets us handle v4-mapped ipv6 addresses a little more nicely, by
storing the addr as an actual v4 sockaddr in conn->local_sockaddr.
Finally, we no longer need to maintain variables for port, since this is
contained in sockaddr. Remove iscsi_np.np_port and iscsi_conn.local_port.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Revert commit 1997e6259, which causes double brackets on ipv6
inaddr_any addresses.
Since we have np_sockaddr, if we need a textual representation we can
use "%pISc".
Change iscsit_add_network_portal() and iscsit_add_np() signatures to remove
*ip_str parameter.
Fix and extend some comments earlier in the function.
Tested to work for :: and ::1 via iscsiadm, previously :: failed, see
https://bugzilla.redhat.com/show_bug.cgi?id=1249107 .
CC: stable@vger.kernel.org
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
REPORT LUNS should not fail just because the allocation length is less
than 16. The relevant section of SPC-4 is:
4.2.5.6 Allocation length
The ALLOCATION LENGTH field specifies the maximum number of bytes or
blocks that an application client has allocated in the Data-In
Buffer. The ALLOCATION LENGTH field specifies bytes unless a
different requirement is stated in the command definition.
An allocation length of zero specifies that no data shall be
transferred. This condition shall not be considered an error.
So we should just truncate our response rather than return an error.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The rd sg lists are never passed to hardware, so use S/G chaining
unonditionally.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
In a performance profile, taking a mutex in iscsit_increment_maxcmdsn()
shows up very high. However taking a mutex around "sess->max_cmd_sn += 1"
seems pretty silly: we're not serializing against other contexts in
any useful way.
I did a quick audit and there don't appear to be any other places that
use max_cmd_sn within the mutex more than once, so this lock can't be
providing any useful serialization.
(Get correct values for logging - fix whitespace damage)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If an initiator doesn't have any real LUNs assigned, we should report
LUN 0 and a LUN list length of 1. Some versions of Solaris at least
go beserk if we report a LUN list length of 0.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a new tpg_enabled_sendtargets configfs attribute
to allow in-band sendtargets discovery information to include
target-portal-groups (TPGs) in !TPG_STATE_ACTIVE state.
This functionality is useful for clustered iSCSI targets, where
TPGTs handled on remote cluster nodes should be advertised in
the SendTargets response.
By default, this new attribute retains the default behaviour of
existing code which to ignore portal-groups in !TPG_STATE_ACTIVE
state.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
IS_ERR(_OR_NULL) already contain an 'unlikely' compiler flag and there
is no need to do that again from its callers. Drop it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
COMPARE AND WRITE requests should fail if DPO or FUA is set, but the
device is not advertising support.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
For every command, we set se_ordered_id by doing atomic_inc_return on
dev->dev_ordered_id for the corresponding device. However, the only
places this value gets used are in pr_debug() calls, which doesn't
seem worth an extra atomic op per IO.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
AIX servers using VIOS servers that virtualize FC cards will have a
problem booting without support for START_STOP_UNIT.
Cite sbc3r36 exactly, clean up if conditions (rob + hch)
Signed-off-by: Brian Bunker <brian@purestorage.com>
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: "Robert Elliott (Server Storage)" <Elliott@hp.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make the warning about unsupported SCSI opcode more useful:
- Add in the initiator name so we know who's sending it.
- Print the warning even for opcodes that spc_parse_cdb() knows about
but that we don't handle.
Signed-off-by: Joern Engel <joern@purestorage.com>
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It's not necessarily a fatal error if a command with a data-out phase
has a data length that differs from the transport data length (e.g.
PERSISTENT RESERVE OUT might have a parameter list length in the CDB
that's smaller than the FC_DL field), so allow these commands. The
Windows compliance test sends them.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Current implementation assumes that all the buffers of an IO are linked
with a single SG list, which is OK because target-core is only allocating
a contigious scatterlist region. However, this assumption is wrong for
se_cmd descriptors that want to use chaining across multiple SGL regions.
Fix this up by using proper SGL accessors for digest payload computation.
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make sure all non-READ SCSI commands get targ_xfer_tag initialized
to 0xffffffff, not just WRITEs.
Double-free of a TUR cmd object occurs under the following scenario:
1. TUR received (targ_xfer_tag is uninitialized and left at 0)
2. TUR status sent
3. First unsolicited NOPIN is sent to initiator (gets targ_xfer_tag of 0)
4. NOPOUT for NOPIN (with TTT=0) arrives
- its ExpStatSN acks TUR status, TUR is queued for removal
- LIO tries to find NOPIN with TTT=0, but finds the same TUR instead,
TUR is queued for removal for the 2nd time
(Drop unbalanced conditional bracket usage - nab)
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
From: Chris Zankel <czankel@purestorage.com>
The initiatorname field in se_acl_lun is only a copy of the same field
in se_node_acl, so remove it and use the version in se_node_acl where
needed (it's actually only used for pr_debug)
Signed-off-by: Chris Zankel <czankel@purestorage.com>
Signed-off-by: Spencer Baugh <spencer.baugh@purestorage.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a v4.2-rc1 regression where backend driver
module unload happening immediately after TBO->free_device()
does internal call_rcu(), will currently result in IRQ context
rcu_process_callbacks() use-after-free paging OOPsen.
It adds the missing rcu_barrier() in target_backend_unregister()
to perform an explicit RCU barrier waiting for all RCU callbacks
to complete before releasing target_backend_ops memory, and
allowing TBO->module exit to proceed.
Also, do the same for fabric drivers in target_unregister_template()
to ensure se_deve_entry->rcu_head -> kfree_rcu() callbacks have
completed, before allowing target_core_fabric_ops->owner module
exit to proceed.
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Currently we have two different ways to signal an I/O error on a BIO:
(1) by clearing the BIO_UPTODATE flag
(2) by returning a Linux errno value to the bi_end_io callback
The first one has the drawback of only communicating a single possible
error (-EIO), and the second one has the drawback of not beeing persistent
when bios are queued up, and are not passed along from child to parent
bio in the ever more popular chaining scenario. Having both mechanisms
available has the additional drawback of utterly confusing driver authors
and introducing bugs where various I/O submitters only deal with one of
them, and the others have to add boilerplate code to deal with both kinds
of error returns.
So add a new bi_error field to store an errno value directly in struct
bio and remove the existing mechanisms to clean all this up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch fixes a regression introduced with the following commit
in v4.0-rc1 code, where an explicit iser-target logout would result
in ->tx_thread_active being incorrectly cleared by the logout post
handler, and subsequent TX kthread leak:
commit 88dcd2dab5
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Thu Feb 26 22:19:15 2015 -0800
iscsi-target: Convert iscsi_thread_set usage to kthread.h
To address this bug, change iscsit_logout_post_handler_closesession()
and iscsit_logout_post_handler_samecid() to only cmpxchg() on
->tx_thread_active for traditional iscsi/tcp connections.
This is required because iscsi/tcp connections are invoking logout
post handler logic directly from TX kthread context, while iser
connections are invoking logout post handler logic from a seperate
workqueue context.
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a regression introduced with the following commit
in v4.0-rc1 code, where a iscsit_start_kthreads() failure triggers
a NULL pointer dereference OOPs:
commit 88dcd2dab5
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Thu Feb 26 22:19:15 2015 -0800
iscsi-target: Convert iscsi_thread_set usage to kthread.h
To address this bug, move iscsit_start_kthreads() immediately
preceeding the transmit of last login response, before signaling
a successful transition into full-feature-phase within existing
iscsi_target_do_tx_login_io() logic.
This ensures that no target-side resource allocation failures can
occur after the final login response has been successfully sent.
Also, it adds a iscsi_conn->rx_login_comp to allow the RX thread
to sleep to prevent other socket related failures until the final
iscsi_post_login_handler() call is able to complete.
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a use-after-free bug in iscsit_release_sessions_for_tpg()
where se_portal_group->session_lock was incorrectly released/re-acquired
while walking the active se_portal_group->tpg_sess_list.
The can result in a NULL pointer dereference when iscsit_close_session()
shutdown happens in the normal path asynchronously to this code, causing
a bogus dereference of an already freed list entry to occur.
To address this bug, walk the session list checking for the same state
as before, but move entries to a local list to avoid dropping the lock
while walking the active list.
As before, signal using iscsi_session->session_restatement=1 for those
list entries to be released locally by iscsit_free_session() code.
Reported-by: Sunilkumar Nadumuttlu <sjn@datera.io>
Cc: Sunilkumar Nadumuttlu <sjn@datera.io>
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As a follow up to ce31c1b0dc - there are
still a few LIO match_int() calls that don't check the return value.
Propagate errors rather than using the potentially uninitialised result.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Here are some more instances where we are returning 0 from a configfs
store function, the unintended result of which is likely infinite retries
from userspace.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
See https://bugzilla.redhat.com/show_bug.cgi?id=1240687
Returning 0 from a configfs store function results in infinite retries.
Reported-by: Yanko Kaneti <yaneti@declera.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case a LU spans 64bit sectors, fixed size sense data information
field is only 32 bits which means the sector information will be truncated.
Thus, if the LU spans 64bit sectors, use descriptor format sense data to
correctly report sector information.
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make sure that the input sense buffer has sufficient length
to fit the information descriptor (12 additional bytes).
Modify scsi_set_sense_information to receive the sense buffer
length and adjust its callers scsi target and libata.
(Fix patch fuzz in scsi_set_sense_information - nab)
Reported-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
PI errors were reported with ILLEGAL_REQUEST sense key but
there was actually no problem with the request. Target
detected PI errors should be reported with aborted command
sense key.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of open coding the sense buffer construction, use
scsi scsi_build_sense_buffer() and scsi_set_sense_information()
helpers which moved to scsi_common.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Move the code for translating a sense_reason_t code into a SCSI status
ASC and ASCQ codes from transport_send_check_condition_and_sense() into
the new function translate_sense_reason(). Convert the switch statement
that performs the translation into table-driven code.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Inline this function in its call site since it performs a trivial
task and since it is only called once.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If the virtual SAS link is set to 'offline' we should be
queueing an I_T_NEXUS_LOSS_OCCURRED UA.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
tcm_loop is able to emulate several protocols, so remove last
vestigies of the SAS protocol.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Since a RAM backend device is not really a rotational device,
we set it as is_nonrot=1 which will be forwarded in VPD page 0xb1
(block device characteristics) response.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
LIO supports protection types 1,3 so setting a hard-coded SPT=3
is fine for now.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Triggered a compilation warning.
Fixes: 2650d71e2 target: move transport ID handling to the core
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Its not a good idea to keep target specific definition of
the same t10-pi tuple.
(Fix v4.2-rc1 patch fuzz - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"It's been a busy development cycle for target-core in a number of
different areas.
The fabric API usage for se_node_acl allocation is now within
target-core code, dropping the external API callers for all fabric
drivers tree-wide.
There is a new conversion to RCU hlists for se_node_acl and
se_portal_group LUN mappings, that turns fast-past LUN lookup into a
completely lockless code-path. It also removes the original
hard-coded limitation of 256 LUNs per fabric endpoint.
The configfs attributes for backends can now be shared between core
and driver code, allowing existing drivers to use common code while
still allowing flexibility for new backend provided attributes.
The highlights include:
- Merge sbc_verify_dif_* into common code (sagi)
- Remove iscsi-target support for obsolete IFMarker/OFMarker
(Christophe Vu-Brugier)
- Add bidi support in target/user backend (ilias + vangelis + agover)
- Move se_node_acl allocation into target-core code (hch)
- Add crc_t10dif_update common helper (akinobu + mkp)
- Handle target-core odd SGL mapping for data transfer memory
(akinobu)
- Move transport ID handling into target-core (hch)
- Move task tag into struct se_cmd + support 64-bit tags (bart)
- Convert se_node_acl->device_list[] to RCU hlist (nab + hch +
paulmck)
- Convert se_portal_group->tpg_lun_list[] to RCU hlist (nab + hch +
paulmck)
- Simplify target backend driver registration (hch)
- Consolidate + simplify target backend attribute implementations
(hch + nab)
- Subsume se_port + t10_alua_tg_pt_gp_member into se_lun (hch)
- Drop lun_sep_lock for se_lun->lun_se_dev RCU usage (hch + nab)
- Drop unnecessary core_tpg_register TFO parameter (nab)
- Use 64-bit LUNs tree-wide (hannes)
- Drop left-over TARGET_MAX_LUNS_PER_TRANSPORT limit (hannes)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (76 commits)
target: Bump core version to v5.0
target: remove target_core_configfs.h
target: remove unused TARGET_CORE_CONFIG_ROOT define
target: consolidate version defines
target: implement WRITE_SAME with UNMAP bit using ->execute_unmap
target: simplify UNMAP handling
target: replace se_cmd->execute_rw with a protocol_data field
target/user: Fix inconsistent kmap_atomic/kunmap_atomic
target: Send UA when changing LUN inventory
target: Send UA upon LUN RESET tmr completion
target: Send UA on ALUA target port group change
target: Convert se_lun->lun_deve_lock to normal spinlock
target: use 'se_dev_entry' when allocating UAs
target: Remove 'ua_nacl' pointer from se_ua structure
target_core_alua: Correct UA handling when switching states
xen-scsiback: Fix compile warning for 64-bit LUN
target: Remove TARGET_MAX_LUNS_PER_TRANSPORT
target: use 64-bit LUNs
target: Drop duplicate + unused se_dev_check_wce
target: Drop unnecessary core_tpg_register TFO parameter
...
Use kvfree() instead of open-coding it.
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Cc: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There are also one new driver: the Cisco snic; the advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions).
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJViKWdAAoJEDeqqVYsXL0MAr8IAMmlA6HBVjMJJFCEOY9corHj
e70MNQa7LUgf+JCdOtzGcvHXTiFFd4IHZAwXUJAnsC4IU2QWEfi1bjUTErlqBIGk
LoZlXXpEHnFpmWot3OluOzzcGcxede8rVgPiKWVVdojIngBC2+LL/i2vPCJ84ri9
WCVlk6KBvWZXuU6JuOKAb2FO9HOX7Q61wuKAMast2Qc6RNc2ksgc7VbstsITqzZ9
FVEsjmQ5lqUj+xdxBpiUOdUpc22IJ4VcpBgQ2HrThvg6vf4aq937RJ/g4vi/g0SU
Utk0a3bUw1H/WnYAfJVFx83nVEsS/954Z7/ERDg1sjlfLYwQtQnpov0XIbPIbZU=
=k9IT
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There is also one new driver: the Cisco snic. The advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (156 commits)
snic: driver for Cisco SCSI HBA
qla2xxx: Fix indentation
qla2xxx: Comment out unreachable code
fusion: remove dead MTRR code
advansys: fix compilation errors and warnings when CONFIG_PCI is not set
mptsas: fix depth param in scsi_track_queue_full
megaraid: fix irq setup process regression
lpfc: Update version to 10.7.0.0 for upstream patch set.
lpfc: Fix to drop PLOGIs from fabric node till LOGO processing completes
lpfc: Fix scsi task management error message.
lpfc: Fix cq_id masking problem.
lpfc: Fix scsi prep dma buf error.
lpfc: Add support for using block multi-queue
lpfc: Devices are not discovered during takeaway/giveback testing
lpfc: Fix vport deletion failure.
lpfc: Check for active portpeerbeacon.
lpfc: Update driver version for upstream patch set 10.6.0.1.
lpfc: Change buffer pool empty message to miscellaneous category
lpfc: Fix incorrect log message reported for empty FCF record.
lpfc: Fix rport leak.
...
The remaining defintions are private to the target core and can be merged
into target_core_internal.h.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Move a little more processing into the core code, and lift the previous
do_unmap callback into the sbc_ops structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of leaking this SBC read/write implementation detail just add an
opaqueue protocol specific pointer to struct se_cmd that we can assign
the sbc_ops vector to.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pointers that are mapped by kmap_atomic() + offset must
be unmapped without the offset. That would cause problems
if the SG element length exceeds the PAGE_SIZE limit.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When changind the LUN inventory via core_enable_device_list_for_node()
or core_disable_device_list_for_node() a REPORTED LUNS DATA HAS CHANGED
UA should be send.
(Convert to target_luns_data_has_changed helper usage - hch)
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
SAM mandates that an BUS DEVICE RESET FUNCTION OCCURRED
UA needs to be send after a LUN RESET tmr has completed.
(Update to use target_ua_allocate_lun - hch)
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When the ALUA target port group changes an INQUIRY DATA CHANGE
UA needs to be sent.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts se_lun->lun_deve_lock acquire/release access
to use a normal, non bottom-half spin_lock_t for protecting
se_lun->lun_deve_list access.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We need to use 'se_dev_entry' as argument when allocating
UAs, otherwise we'll never see any UAs for an implicit
ALUA state transition triggered from userspace.
(Add target_ua_allocate_lun() common caller - nab)
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When switching target port group ALUA states we need to send
one UA when setting the ALUA state to 'transitioning', and
another one once the final state has been set.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
LUN allocation is now fully dynamic, so there is no need to
artificially restrain the number of exported LUNs.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As we're now using a list to hold the LUNs the target core
can now converted to use 64-bit LUNs internally.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch drops unnecessary target_core_fabric_ops parameter usage
for core_tpg_register() during fabric driver TFO->fabric_make_tpg()
se_portal_group creation callback execution.
Instead, use the existing se_wwn->wwn_tf->tf_ops pointer to ensure
fabric driver is really using the same TFO provided at module_init
time.
Also go ahead and drop the forward TFO declarations tree-wide, and
handling the special case for iscsi-target discovery TPG.
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Only include SCSI initiator header files in target code that needs
these header files, namely the SCSI pass-through code and the tcm_loop
driver. Change SCSI_SENSE_BUFFERSIZE into TRANSPORT_SENSE_BUFFER in
target code because the former is intended for initiator code and the
latter for target code. With this patch the only initiator include
directives in target code that remain are as follows:
$ git grep -nHE 'include .scsi/(scsi.h|scsi_host.h|scsi_device.h|scsi_cmnd.h)' drivers/target drivers/infiniband/ulp/{isert,srpt} drivers/usb/gadget/legacy/tcm_*.[ch] drivers/{vhost,xen} include/{target,trace/events/target.h}
drivers/target/loopback/tcm_loop.c:29:#include <scsi/scsi.h>
drivers/target/loopback/tcm_loop.c:31:#include <scsi/scsi_host.h>
drivers/target/loopback/tcm_loop.c:32:#include <scsi/scsi_device.h>
drivers/target/loopback/tcm_loop.c:33:#include <scsi/scsi_cmnd.h>
drivers/target/target_core_pscsi.c:39:#include <scsi/scsi_device.h>
drivers/target/target_core_pscsi.c:40:#include <scsi/scsi_host.h>
drivers/xen/xen-scsiback.c:52:#include <scsi/scsi_host.h> /* SG_ALL */
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
With se_port_t and t10_alua_tg_pt_gp_member being absored into se_lun,
there is no need for an extra atomic_t based reference count for PR
ALL_TG_PT=1 and ALUA access state transition.
Go ahead and use the existing percpu se_lun->lun_ref instead, and
convert the two special cases to percpu_ref_tryget_live() to avoid
se_lun if transport_clear_lun_ref() has already been invoked to
shutdown the se_lun.
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
With se_port and t10_alua_tg_pt_gp_member being absored into se_lun,
there is no need for an extra lock to protect se_lun->lun_se_dev
assignment.
This patch also converts backend drivers to use call_rcu() release
to allow any se_device readers to complete. The call_rcu() instead
of kfree_rcu() is required here because se_device is embedded into
the backend driver specific structure.
Also, convert se_lun->lun_stats to use atomic_long_t within the
target_complete_ok_work() completion callback, and add FIXME for
transport_lookup_tmr_lun() with se_lun->lun_ref.
Finally, update sbp_update_unit_directory() special case usage with
proper rcu_dereference_raw() and configfs symlink comment.
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Chris Boot <bootc@bootc.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch eliminates all se_port + t10_alua_tg_pt_gp_member usage,
and converts current users to direct se_lun pointer dereference.
This includes the removal of core_export_port(), core_release_port()
core_dev_export() and core_dev_unexport(). Along with conversion
of special case se_lun pointer dereference within PR ALL_TG_PT=1
and ALUA access state transition UNIT_ATTENTION handling.
Also, update core_enable_device_list_for_node() to reference the
new per se_lun->lun_deve_list when creating a new entry, or
replacing an existing one via RCU.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of starting a thread from transport_clear_lun_ref() that
waits for LUN shutdown, wait in that function for LUN shutdown
to finish. Additionally, change the return type of
transport_clear_lun_ref() from int to void.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Consolidate the implementation of the backend attributes in a single file
and single function per attribute show/store function instead of splitting
it into multiple functions in multiple files.
Also use the proper strto* helpers for exposed data types, add macros to
implement the store methods for the most common data types and share the
show methods between the two different attribute implementations.
(Fix bogus store_pi_prot_format flag=0 return value - nab)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Provide a common sets of dev_attrib attributes for all devices using the
generic SPC/SBC parsers, and a second one with the minimal required read-only
attributes for passthrough devices. The later is only used by pscsi for now,
but will be wired up for the full-passthrough TCMU use case as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Rewrite the backend driver registration based on what we did to the fabric
drivers: introduce a read-only struct target_bakckend_ops that the driver
registers, which is then instanciate as a struct target_backend by the
core. This allows the ops vector to be smaller and allows us to mark it
const. At the same time the registration function can set up the
configfs attributes, avoiding the need to add additional boilerplate code
for that to the drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that se_portal_group->tpg_lun_hlist is a RCU protected hlist,
go ahead and drop the left-over lun->lun_status usage.
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes core_tpg_add_node_to_devs() to avoid unnecessarly
resetting every se_dev_entry in se_node_acl->tpg_lun_hlist when the
operation is driven by an explicit configfs se_lun->lun_group creation
via core_dev_add_lun() to only update a single se_lun.
Otherwise for the second core_tpg_check_initiator_node_acl() case, go
ahead and continue to scan the full set of currently active se_lun in
se_portal_group->tpg_lun_hlist.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts core_tpg_deregister() to perform a list splice
for any remaining dynamically generated se_node_acls attached to
se_tpg, before calling kfree(nacl) to free memory.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts se_tpg->acl_node_lock to struct mutex, so that
->acl_node_acl walkers in core_clear_lun_from_tpg() can block when
calling core_disable_device_list_for_node().
It also updates core_dev_add_lun() to hold ->acl_node_mutex when
calling core_tpg_add_node_to_devs() to build ->lun_entry_hlist
for dynamically generated se_node_acl.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts the fixed size se_portal_group->tpg_lun_list[]
to use modern RCU with hlist_head in order to support an arbitary
number of se_lun ports per target endpoint.
It includes dropping core_tpg_alloc_lun() from core_dev_add_lun(),
and calling it directly from target_fabric_make_lun() to allocate
a new se_lun. And add a new target_fabric_port_release() configfs
item callback to invoke kfree_rcu() to release memory during
se_lun->lun_group shutdown.
Also now that se_node_acl->lun_entry_hlist is using RCU, convert
existing tpg_lun_lock to struct mutex so core_tpg_add_node_to_devs()
can perform RCU updater logic without releasing ->tpg_lun_mutex.
Also, drop core_tpg_clear_object_luns() and it's single consumer
in iscsi-target, which is duplicating TPG LUN shutdown logic and
is current code results in a NOP.
Finally, sbp-target and xen-scsiback fabric driver conversions are
included, which are required due to the non-standard way they use
->tpg_lun_hlist.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Chris Boot <bootc@bootc.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Clean up the mess of registered variables, and pass the isid mismatch
flag explicitly instead of overloading the registration type.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes __core_scsi3_do_alloc_registration() code to
drop pr_reg->pr_reg_tg_pt_lun pointer usage in favor of a new
pr_reg RPTI + existing pr_reg->pr_aptpl_target_lun used by
APTPL metadata logic.
It also includes changes to REGISTER, REGISTER_AND_MOVE and APTPL
feature bit codepaths to use rcu_dereference_check() with the
expected non-zero se_dev_entry->pr_kref reference held.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts the core_scsi3_pr_seq_non_holder() check for non
reservation holding registrations to use an atomic bitop in ->deve_flags
to determine if a registration is currently active.
It also includes associated a set_bit() in __core_scsi3_add_registration()
and clear_bit() in __core_scsi3_free_registration(), if se_dev_entry still
exists, and has not already been released via se_dev_entry shutdown path
in core_disable_device_list_for_node().
Also, clear_bit in core_disable_device_list_for_node as well to ensure
the read-critical path in core_scsi3_pr_seq_non_holder() picks up the
new state, preceeding the final kfree_rcu() call.
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts se_node_acl->device_list[] table for mappedluns
to modern RCU hlist_head usage in order to support an arbitrary number
of node_acl lun mappings.
It converts transport_lookup_*_lun() fast-path code to use RCU read path
primitives when looking up se_dev_entry. It adds a new hlist_head at
se_node_acl->lun_entry_hlist for this purpose.
For transport_lookup_cmd_lun() code, it works with existing per-cpu
se_lun->lun_ref when associating se_cmd with se_lun + se_device.
Also, go ahead and update core_create_device_list_for_node() +
core_free_device_list_for_node() to use ->lun_entry_hlist.
It also converts se_dev_entry->pr_ref_count access to use modern
struct kref counting, and updates core_disable_device_list_for_node()
to kref_put() and block on se_deve->pr_comp waiting for outstanding PR
special-case PR references to drop, then invoke kfree_rcu() to wait
for the RCU grace period to complete before releasing memory.
So now that se_node_acl->lun_entry_hlist fast path access uses RCU
protected pointers, go ahead and convert remaining non-fast path
RCU updater code using ->lun_entry_lock to struct mutex to allow
callers to block while walking se_node_acl->lun_entry_hlist.
Finally drop the left-over core_clear_initiator_node_from_tpg() that
originally cleared lun_access during se_node_acl shutdown, as post
RCU conversion it now becomes duplicated logic.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The only instance of ->put_session is in qla2xxx, and was added by commit
aaf68b ("tcm_qla2xxx: Convert to TFO->put_session() usage") with the following
description:
This patch converts tcm_qla2xxx code to use an internal kref_put() for
se_session->sess_kref in order to ensure that qla_hw_data->hardware_lock
can be held while calling qlt_unreg_sess() for the final put.
But these day we're already holding the hardware lock over qlt_unreg_sess in
the ->close_session callback, so we're fine without this method.
(Re-add missing tcm_qla2xxx_release_session + drop put_session usage - nab)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It's only embedded into struct target_fabric_configfs these days, so we
might as well remove this layer of abstraction.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove all fields that are either unused or can be replaced by trivially
following pointers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that we don't need to set up ->tf_subsys we don't need to copy around
the ops vector anymore.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Detected these variables by building with W=1.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simplify target core and target drivers by storing the task tag
a.k.a. command identifier inside struct se_cmd.
For several transports (e.g. SRP) tags are 64 bits wide.
Hence add support for 64-bit tags.
(Fix core_tmr_abort_task conversion spec warnings - nab)
(Fix up usb-gadget to use 16-bit tags - HCH + bart)
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that struct se_portal_group contains a protocol identifier field we can
take all the code to format an parse protocol identifiers in CDBs into common
code instead of leaving this to low-level drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that we store the protocol identifier in the tpg structure we don't
need this method.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove the unneeded fabric_ptr argument, and change the type argument
to pass in a SPC protocol identifier.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
sbc_dif_generate() and sbc_dif_verify() currently assume that each
SG element for data transfer memory doesn't straddle the block size
boundary.
However, when using SG_IO ioctl, we can choose the data transfer
memory which doesn't satisfy that alignment requirement.
In order to handle such cases correctly, this change inverts the outer
loop to iterate data transfer memory and the inner loop to iterate
protection information and enables to calculate CRC for a block which
straddles multiple SG elements.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: target-devel@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Even if the device backend is initialized with protection info is
enabled, some requests don't have the protection info attached for
WRITE SAME command issued by block device helpers, WRITE command with
WRPROTECT=0 by SG_IO ioctl, etc.
So when TCM loopback fabric module is used, se_cmd->t_prot_sg is NULL
for these requests and performing WRITE_INSERT of PI using software
emulation by sbc_dif_generate() causes kernel crash.
To fix this, introduce SCF_PASSTHROUGH_PROT_SG_TO_MEM_NOALLOC for
se_cmd_flags, which is used to determine that se_cmd->t_prot_sg needs
to be allocated or use pre-allocated protection information by scsi
mid-layer.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: target-devel@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In sbc_dif_copy_prot(), the addresses passed to kunmap_atomic() are
inconsistent with the addresses which are mapped by kmap_atomic().
That could be problematic if an SG element has its length larger than
PAGE_SIZE as kunmap_atomic() will attempt to unmap different page.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: target-devel@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Linus Torvalds
Andy Grover
Roland Dreier
Christoph Hellwig
David Disseldorp
Viresh Kumar
Brian Bunker
Joern Engel
Alexei Potashnik
Chris Zankel
Nicholas Bellinger
Sagi Grimberg
Bart Van Assche
Hannes Reinecke
Pekka Enberg
Stephen Rothwell
David S. Miller
Christophe Vu-Brugier
Akinobu Mita