Marcell Zambo and Janos Farago noticed and reported that when
new conntrack entries are added via netlink and the conntrack table
gets full, soft lockup happens. This is because the nf_conntrack_lock
is held while nf_conntrack_alloc is called, which is in turn wants
to lock nf_conntrack_lock while evicting entries from the full table.
The patch fixes the soft lockup with limiting the holding of the
nf_conntrack_lock to the minimum, where it's absolutely required.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When the controller gets brought up for initial setup, it will be brought
back down after a timeout. In that case, don't send a New Settings event.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a new controller gets added to the system, it needs to be brought
up briefly to read basic information like features, BD_ADDR etc. and
after a timeout it will be brought back down.
The only command that should overwrite this timeout is the set power
command from the management interface. Just reading the controller
list or information is not a good reason to keep the controller up.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Assorted fixes, sat in -next for a week or so...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ocfs2: deal with wraparounds of i_nlink in ocfs2_rename()
vfs: fix compat_sys_stat() handling of overflows in st_nlink
quota: Fix deadlock with suspend and quotas
vfs: Provide function to get superblock and wait for it to thaw
vfs: fix panic in __d_lookup() with high dentry hashtable counts
autofs4 - fix lockdep splat in autofs
vfs: fix d_inode_lookup() dentry ref leak
EIR shouldn't be enabled if SSP isn't enabled. This patch adds the
clearing of EIR data when disabling SSP and restores the data when SSP
is re-enabled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
If the local controller doesn't support SSP we should always return an
error for the Set SSP command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds rudimentary support for the Set High Speed command in
the form of a new HCI dev flag (HCI_HS_ENABLED).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds an address type parameter to the Discovering event. The
value matches that given to Start/Stop Discovery.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds an address type parameter to the Stop Discovery command
which should match the value given to Start Discovery.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The management interface API has reached stable version 1.0 and thus
it can now be always enabled. All future changes will be made backwards
compatible.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since neither High Speed (HS) nor Low Energy (LE) are fully implemented
yet, only expose them in supported settings when enabled.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The management interface on the HCI control channel should be restricted
to applications with CAP_NET_ADMIN permission.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI monitor channel can be used to monitor all packets and events
from the Bluetooth subsystem. The monitor is not bound to any specific
HCI device and allows even capturing multiple devices at the same time.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use helper functions aware of COMPAT_USE_64BIT_TIME to write struct
timeval and struct timespec to userspace in net/socket.c.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Handle 64-bit time structures in the networking core compat code.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: David S. Miller <davem@davemloft.net>
Enable the Bluetooth subsystem to be used with a compat ABI with
64-bit time.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo F. Padovan <padovan@profusion.mobi>
Cc: David S. Miller <davem@davemloft.net>
The HCI notifier handling was never used outside of Bluetooth core layer
and thus remove it and replace it with direct function calls. Also move
the stack internal event generation into the HCI socket layer.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Any HCI raw socket gets a copy of each SKB that is either received or
send via the Bluetooth subsystem. The raw socket uses SKB clones to
send out data, but the problem is that it needs to add an extra packet
type byte in front of it. And some drivers need to also add an extra
header before submitting the packet.
So far this all worked magically fine since all of the drivers and the
raw sockets are adding the same byte at the same location. But that is
by pure coincidence. Since the data of cloned SKBs is shared, this means
that the raw socket and driver kept writing into the shared data area.
To fix this the only safe way is if the HCI raw socket creates a copy of
the SKB before sending it out. To not always copy all SKBs around, the
copy is only created once and only after any of the HCI filter checks
succeeded.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI socket bind handling checks a few too many times the channel
we are binding. So centralize this and make the function easier to read.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI CMSG specific data is for raw sockets only. So only add them to
actual raw sockets.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When reading the HCI raw socket option, the socket was never locked. So
lock the socket and in addition return EINVAL on non raw sockets.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Currently the socket options of HCI sockets can be set on raw and control
sockets, but on control sockets they make no sense. So just return EINVAL
in that case.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bt_cb(skb)->channel was only needed to make hci_send_to_sock() be
used for HCI raw and control sockets. Since they have now separate sending
functions this is no longer needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The sending functions for HCI raw and control sockets have nothing in
common except that they iterate over the socket list. Split them into
two so they can do their job more efficient. In addition the code becomes
more readable.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
commit 50612537e9 (netem: fix classful handling) added two errors in
netem_dequeue()
1) After checking skb at the head of tfifo queue for time constraints,
it dequeues tail skb, thus adding unwanted reordering.
2) qdisc stats are updated twice per packet
(one when packet dequeued from tfifo, once when delivered)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c
Small minor conflict in bnx2x, wherein one commit changed how
statistics were stored in software, and another commit
fixed endianness bugs wrt. reading the values provided by
the chip in memory.
Signed-off-by: David S. Miller <davem@davemloft.net>
The hci_connect function should either return a valid hci_conn pointer
or a ERR_PTR() but never NULL. This patch fixes the two places where
hci_conn_add failures would have caused a NULL return. The only reason
for failure with hci_conn_add is memory allocation so ENOMEM seems to be
a good choice here.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch bumps the mgmt version to 1 and resets the revision to 0.
This is in order to indicate API stability to user space. The mgmt API
has reached a point where no major backwards incompatible changes are
expected so it makes sense to do this version bump now.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The response to the Add/Remove Out Of Band Data commands should include
the same address as was given in the command itself.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The same address as was passed to the (Un)Block Device command should
also be returned in the command response message.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The same address type that was passed to the Start Discovery command
should also be returned in the response message.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes the status in Pair Device responses to follow proper
mgmt status values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Instead of having status paramters part of each individual command
response it's simpler to just have the status as part of the command
complete header. This patch updates the code to follow this convention
and thereby also ensures compliance with the latest mgmt API
specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds interleaved discovery support to MGMT Start
Discovery command.
In case interleaved discovery is not supported (not a dual mode
device), we perform BR/EDR or LE-only discovery according to the
device capabilities.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch merges DISCOVERY_INQUIRY and DISCOVERY_LE_SCAN states
into a new state called DISCOVERY_FINDING.
From the discovery perspective, we are pretty much worried about
to know just if we are finding devices than what exactly phase of
"finding devices" (inquiry or LE scan) we are currently running.
Besides, to know if the controller is performing inquiry or LE scan
we should check HCI_INQUIRY or HCI_LE_SCAN bits in hdev flags.
Moreover, merging this two states will simplify the discovery state
machine and will keep interleaved discovery implementation simpler.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds to struct discovery_state the field 'type' so that
we can track the discovery type the device is performing.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch does some code refactoring in start_discovery function
in order to prepare it for interleaved discovery support.
MGMT_ADDR_* macros were moved to hci_core.h since they are now used
to define discovery type macros.
Discovery type macros were defined according to mgmt-api.txt
specification:
Possible values for the Type parameter are a bit-wise or of the
following bits:
1 BR/EDR
2 LE Public
3 LE Random
By combining these e.g. the following values are possible:
1 BR/EDR
6 LE (public & random)
7 BR/EDR/LE (interleaved discovery)
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The svcrdma transport was un-marshalling requests in-place. This resulted
in sparse warnings due to __beXX data containing both NBO and HBO data.
The code has been restructured to do byte-swapping as the header is
parsed instead of when the header is validated immediately after receipt.
Also moved extern declarations for the workqueue and memory pools to the
private header file.
Signed-off-by: Tom Tucker <tom@ogc.us>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Remove dev_addr in interface_setup(), it's not needed anymore.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: use bitops, adapt to eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include RPC statistics from all data servers in /proc/self/mountstats for pNFS
filelayout mounts.
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch adds the appropriate Intel copyright to mgmt files.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The latest mgmt API includes an address type for all messages containing
an address. This patch updates the confirm name command to match this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The latest mgmt API includes address types for all messages containing
an address. This patch updates the PIN code messages to match this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The latest mgmt API includes an address type wherever there's an address
present. This patch updates the link key messages to match it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Several hex numbers were printed without object name which
complicates debugging.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use state_to_string function in debug statements.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Function state_to_string will be used in other files in debug
statements.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use specific logging functions instead of a generic
bt_printk function can save some text.
Remove now unused bt_printk function.
Add compatibility BT_INFO and BT_ERR macros.
(compiled x86 and defconfig with bluetooth and all bluetooth drivers)
$ size net/bluetooth/built-in.o*
text data bss dec hex filename
381662 20072 100416 502150 7a986 net/bluetooth/built-in.o.allyesconfig.new
382463 20072 100400 502935 7ac97 net/bluetooth/built-in.o.allyesconfig.old
126635 1388 132 128155 1f49b net/bluetooth/built-in.o.defconfig.new
127175 1388 132 128695 1f6b7 net/bluetooth/built-in.o.defconfig.old
$ size drivers/bluetooth/built-in.o*
127575 8976 29476 166027 2888b drivers/bluetooth/built-in.o.allyesconfig.new
129512 8976 29516 168004 29044 drivers/bluetooth/built-in.o.allyesconfig.old
52998 3292 156 56446 dc7e drivers/bluetooth/built-in.o.defconfig.new
54358 3292 156 57806 e1ce drivers/bluetooth/built-in.o.defconfig.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Set SSP mgmt command can be used for enabling and disabling Secure
Simple Pairing support for controllers that support it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The Set Link Security mgmt command is used to enable or disable link
level security, also known as Security Mode 3. This is rarely enabled in
modern systems but the command needs to be available for completeness,
qualification purposes and those few systems that actually want to
enable it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
For simple integer errors the variable name "err" is more consistent
with the existing code base than "ret".
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The val member of cmd_lookup isn't used anywhere so it can be removed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
With static RPC slots, the xprt backlog queue stats were useful in showing
when the transport (TCP) was starved by lack of RPC slots. The new dynamic
RPC slot code, commit d9ba131d8f, always
provides an RPC slot and so only uses the xprt backlog queue when the
tcp_max_slot_table_entries value has been hit or when an allocation error
occurs. All requests are now placed on the xprt sending or pending queue which
need to be monitored for debugging.
The max_slot stat shows the maximum number of dynamic RPC slots reached which is
useful when debugging performance issues.
Add the new fields at the end of the mountstats xprt stanza so that mountstats
outputs the previous correct values and ignores the new fields. Bump
NFS_IOSTATS_VERS.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Actually the TT_CLIENT_PENDING flag is never set in the tt_global_entry
structure, therefore this code is useless and can be removed.
Reported-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Each tt_local_set_pending is always followed by a bat_dbg invocation. This can
be simplified by moving the bat_dbg() call.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
In case of a new tt_local_entry, the TT_CLIENT_NEW flag has to be set before
adding such entry to the hash table. Otherwise, it opens a race condition
in which the entry can be found but the flag has not been set.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
To increase readability the has_timed_out() functions has been introduced.
This patch converts existing time_after() calls to use this wrapper
function (if applicable).
This patch also converts all timeouts to miliseconds to be consistent.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Both translation tables and network coding use timeouts to do house
keeping, so we might as well share the function used to compare a
timestamp+timeout with current time.
For readability and simplicity, the function is renamed to
has_timed_out() and uses time_is_before_jiffies() instead of
time_after().
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Most of the values in that call are derived from the skb, so we can hand
over the skb instead.
Reported-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
All batman-adv packets have a common 3 byte header. It can be used to share
some code between different code paths, but it was never explicit stated that
this header has to be always the same for all packets. Therefore, new code
changes always have the problem that they may accidently introduce regressions
by moving some elements around.
A new structure is introduced that contains the common header and makes it
easier visible that these 3 bytes have to be the same for all on-wire packets.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
(ttvn == 0) is currently used as initial condition. However this is not a good
idea because ttvn gets the vale zero each time after reaching the maximum value
(wrap around). For this reason a new flag is added in order to define whether a
node has an initialised table or not. Moreover, after invoking
tt_global_del_orig(), tt_initialised has to be set to false
Reported-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace usage of random_ether_addr() with eth_hw_addr_random()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Change the trivial cases.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most rate control implementations assume .get_rate and .tx_status are only
called once the per-station data has been fully initialized.
minstrel_ht crashes if this assumption is violated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are situations where we don't have the
necessary rate control information yet for
station entries, e.g. when associating. This
currently doesn't really happen due to the
dummy station handling; explicitly disabling
rate control when it's not initialised will
allow us to remove dummy stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are not supposed to send mgmt_discovering events if we are transiting
from DISCOVERY_STARTING to DISCOVERY_STOPPED state. It doesn't make
sense to send mgmt_discovering event once discovery procedure has not
been even started.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case of Start Discovery command failure, we should set the discovery
state to DISCOVERY_STOPPED. Otherwise, we stuck at DISCOVERY_STARTING
state and subsequent Start Discovery commands will simply fail.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch implements the Read Supported Commands mgmt command which was
recently added to the API specification. It returns a list of supported
commands and events to user space.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
We need to use the _sync() version for cancelling the info and security
timer in the L2CAP connection delete path. Otherwise the delayed work
handler might run after the connection object is freed.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
__cancel_delayed_work() is being used in some paths where we cannot
sleep waiting for the delayed work to finish. However, that function
might return while the timer is running and the work will be queued
again. Replace the calls with safer cancel_delayed_work() version
which spins until the timer handler finishes on other CPUs and
cancels the delayed work.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We should only perform a reset in hci_dev_do_close if the
HCI_QUIRK_NO_RESET flag is set (since in such a case a reset will not be
performed when initializing the device).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
There is an imbalance in the rfcomm_session_hold / rfcomm_session_put
operations which causes the following crash:
[ 685.010159] BUG: unable to handle kernel paging request at 6b6b6b6b
[ 685.010169] IP: [<c149d76d>] rfcomm_process_dlcs+0x1b/0x15e
[ 685.010181] *pdpt = 000000002d665001 *pde = 0000000000000000
[ 685.010191] Oops: 0000 [#1] PREEMPT SMP
[ 685.010247]
[ 685.010255] Pid: 947, comm: krfcommd Tainted: G C 3.0.16-mid8-dirty #44
[ 685.010266] EIP: 0060:[<c149d76d>] EFLAGS: 00010246 CPU: 1
[ 685.010274] EIP is at rfcomm_process_dlcs+0x1b/0x15e
[ 685.010281] EAX: e79f551c EBX: 6b6b6b6b ECX: 00000007 EDX: e79f40b4
[ 685.010288] ESI: e79f4060 EDI: ed4e1f70 EBP: ed4e1f68 ESP: ed4e1f50
[ 685.010295] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 685.010303] Process krfcommd (pid: 947, ti=ed4e0000 task=ed43e5e0 task.ti=ed4e0000)
[ 685.010308] Stack:
[ 685.010312] ed4e1f68 c149eb53 e5925150 e79f4060 ed500000 ed4e1f70 ed4e1f80 c149ec10
[ 685.010331] 00000000 ed43e5e0 00000000 ed4e1f90 ed4e1f9c c149ec87 0000bf54 00000000
[ 685.010348] 00000000 ee03bf54 c149ec37 ed4e1fe4 c104fe01 00000000 00000000 00000000
[ 685.010367] Call Trace:
[ 685.010376] [<c149eb53>] ? rfcomm_process_rx+0x6e/0x74
[ 685.010387] [<c149ec10>] rfcomm_process_sessions+0xb7/0xde
[ 685.010398] [<c149ec87>] rfcomm_run+0x50/0x6d
[ 685.010409] [<c149ec37>] ? rfcomm_process_sessions+0xde/0xde
[ 685.010419] [<c104fe01>] kthread+0x63/0x68
[ 685.010431] [<c104fd9e>] ? __init_kthread_worker+0x42/0x42
[ 685.010442] [<c14dae82>] kernel_thread_helper+0x6/0xd
This issue has been brought up earlier here:
https://lkml.org/lkml/2011/5/21/127
The issue appears to be the rfcomm_session_put in rfcomm_recv_ua. This
operation doesn't seem be to required as for the non-initiator case we
have the rfcomm_process_rx doing an explicit put and in the initiator
case the last dlc_unlink will drive the reference counter to 0.
There have been several attempts to fix these issue:
6c2718d Bluetooth: Do not call rfcomm_session_put() for RFCOMM UA on closed socket
683d949 Bluetooth: Never deallocate a session when some DLC points to it
but AFAICS they do not fix the issue just make it harder to reproduce.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Gopala Krishna Murala <gopala.krishna.murala@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
After moving L2CAP timers to workqueues l2cap_set_timer expects timeout
value to be specified in jiffies but constants defined in miliseconds
are used. This makes timeouts unreliable when CONFIG_HZ is not set to
1000.
__set_chan_timer macro still uses jiffies as input to avoid multiple
conversions from/to jiffies for sk_sndtimeo value which is already
specified in jiffies.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Ackec-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
sk_sndtime value should be specified in jiffies thus initial value
needs to be converted from miliseconds. Otherwise this timeout is
unreliable when CONFIG_HZ is not set to 1000.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
As reported by Dan Carpenter this function causes a Sparse warning and
shouldn't be declared inline:
include/net/bluetooth/l2cap.h:837:30 error: marked inline, but without a
definition"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Commit 330605423c fixed l2cap conn establishment for non-ssp remote
devices by not setting HCI_CONN_ENCRYPT_PEND every time conn security
is tested (which was always returning failure on any subsequent
security checks).
However, this broke l2cap conn establishment for ssp remote devices
when an ACL link was already established at SDP-level security. This
fix ensures that encryption must be pending whenever authentication
is also pending.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The tracepoint code relies on the queue->name being defined in order to
be able to display the name of the waitqueue on which an RPC task is
sleeping.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
This patch introduces per-net Lockd initialization and destruction routines.
The logic is the same as in global Lockd up and down routines. Probably the
solution is not the best one. But at least it looks clear.
So per-net "up" routine are called only in case of lockd is running already. If
per-net resources are not allocated yet, then service is being registered with
local portmapper and lockd sockets created.
Per-net "down" routine is called on every lockd_down() call in case of global
users counter is not zero.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This function is enough for releasing resources, allocated for network
namespace context, in case of sharing service between them.
IOW, each service "user" (LockD, NFSd, etc), which wants to share service
between network namespaces, have to release related resources by the function,
introduced in this patch, instead of performing service shutdown (of course in
case the service is shared already to the moment of release).
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
v2: Added comment to BUG_ON's in svc_destroy() to make code looks clearer.
This patch introduces network namespace filter for service destruction
function.
Nothing special here - just do exactly the same operations, but only for
tranports in passed networks namespace context.
BTW, BUG_ON() checks for empty service transports lists were returned into
svc_destroy() function. This is because of swithing generic svc_close_all() to
networks namespace dependable svc_close_net().
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch moves service transports deletion from service sockets lists to
separated function.
This is a precursor patch, which would be usefull with service shutdown in
network namespace context, introduced later in the series.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch moves removing of service transport from it's pools ready lists to
separated function. Also this clear is now done with list_for_each_entry_safe()
helper.
This is a precursor patch, which would be usefull with service shutdown in
network namespace context, introduced later in the series.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
commit 5a698af53f (bond: service netpoll arp queue on master device)
tested IFF_SLAVE flag against dev->priv_flags instead of dev->flags
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: WANG Cong <amwang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first parameter should be "number of elements" and the second parameter
should be "element size".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit ensures that lost_cnt_hint is correctly updated in
tcp_shifted_skb() for FACK TCP senders. The lost_cnt_hint adjustment
in tcp_sacktag_one() only applies to non-FACK senders, so FACK senders
need their own adjustment.
This applies the spirit of 1e5289e121 -
except now that the sequence range passed into tcp_sacktag_one() is
correct we need only have a special case adjustment for FACK.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the number of dentry cache hash table entries gets too high
(2147483648 entries), as happens by default on a 16TB system, use of a
signed integer in the dcache_init() initialization loop prevents the
dentry_hashtable from getting initialized, causing a panic in
__d_lookup(). Fix this in dcache_init() and similar areas.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
net/sched/sch_plug.c:211:18: warning: symbol 'plug_qdisc_ops' was not
declared. Should it be static?
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_gro_receive() doesnt update truesize properly when adding one skb to
frag_list.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enhances code readability a lot and avoids using void* even though
we know the type of the variable.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This avoids using the dev_set/get_drvdata() functions to retrieve a
pointer to our own structure. We can use simple pointer arithmetic here.
The drvdata field is actually not needed by any other code-path but this
makes the code more consistent with hci_dev.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We currently use dev_set_drvdata to keep a pointer to ourself. This
doesn't make sense as we are the bus and not a driver. Therefore,
introduce to_hci_dev() so we can get a struct hci_dev pointer from a
struct device pointer.
dev_set/get_drvdata() is reserved for drivers that provide a device and
not for the bus using the device. The bus can use simple pointer
arithmetic to retrieve its private data.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch add a new Device Unpaired mgmt event. This will be sent to
all mgmt sockets except the one that requested unpairing (that socket
will get a command complete instead). The event is also reserved for
future SMP updates where a remote device will be able to request pairing
revocation from us.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The default response status to unpair_device should be set as 0 instead
of a generic failure value. When disconnection is not needed (i.e. we
can reply imediately) we should return success and not failure.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch updates the Authentication Failed mgmt event to match the
latest API specification by adding an address type to it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch updates the implmentation for mgmt_block_device and
mgmt_unblock_device and their corresponding events to match the latest
API specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch updates the implementation for these mgmt to be up to date
with the latest API specification. Right now the address type isn't
actually used for anything but that might change in the future.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch upadate the user confirm and user passkey mgmt messages to
match the latest API specification by adding an address type parameter
to them.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds an address type parameter to the disconnect command and
response in order to match the latest mgmt API specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch renames the mgmt_remove_keys command to mgmt_unpair_device
and updates its parameters to match the latest API (specifically, it
adds an address type parameter to the command and its response).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Pending I-Frame(s) are considered as acknowledgement. To void double
acking (via I-Frame and later via RR) clear ack timer when sending
first pending I-Frame.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Make l2cap_ertm_send return number of pending I-Frames transmitted
instead of all (pending + retransmitted) I-Frames transmitted.
As only pending I-Frames are considered as acknowledgement, this could
lead to situation when no ACK was sent in __l2cap_send_ack (if only
already transmitted I-Frames were retransmitted).
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In debug use chan %p instead of sk.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Change elseif to switch. This make sense even more with following
patches which otherwise have to add more elseifs statements.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Change is needed to remove dependency on sk when possible
before introducing l2cap channel lock.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is helpful for device discovery implementation & debuging.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The correct length of the event is the size of the ev struct (not size
of the pointer like the code was previously using) plus the length of
the variable-sized EIR data at the end of the struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes a #define indentation in mgmt.c.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds LE-Only discovery procedure support to MGMT Start
Discovery command.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We are not supposed to block in start_discovery() because
start_discovery code is running in write() syscall context
and this would block the write operation on the mgmt socket.
This way, we cannot directly call hci_do_le_scan() to scan
LE devices in start_discovery(). To overcome this issue a
derefered work (hdev->le_scan) was created so we can properly
call hci_do_le_scan().
The helper function hci_le_scan() simply set LE scan parameters
and queue hdev->le_scan work. The work is queued on system_long_wq
since it can sleep for a few seconds in the worst case (timeout).
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds to hci_core the hci_do_le_scan function which
should be used to scan LE devices.
In order to enable LE scan, hci_do_le_scan() sends commands (Set
LE Scan Parameters and Set LE Scan Enable) to the controller and
waits for its results. If commands were executed successfully a
delayed work is scheduled to disable the ongoing scanning after
some amount of time. This function blocks.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch does a trivial code refacting in hci_discovery_active.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Send MGMT Discovering events once LE scan starts/stops so the
userspace can track when local adapters are discovering LE devices.
This way, we also keep the same behavior of inquiry which sends MGMT
Discovering events once inquiry starts/stops even if it is triggered
by an external tool (e.g. hcitool).
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We should only perform a reset in hci_dev_do_close if the
HCI_QUIRK_NO_RESET flag is set (since in such a case a reset will not be
performed when initializing the device).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
If we want to have proper pairing support over LE we need to
inform userspace that a new LTK is available, so userspace
can store that key permanently.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of having a separated command for removing SMP keys, we use the
Remove Keys command to remove *all* keys.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds a method to notify that a new LTK is available and
a handler to store keys coming from userspace into the kernel LTK
list.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This updates all the users of the older way, that was using the
link_keys list to store the SMP keys, to use the new way.
This includes defining new types for the keys, we have a type for each
combination of STK/LTK and Master/Slave.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This includes a new list for storing the keys and a new structure used
to represent each key.
Some notes: authenticated is used to identify that the key may be used
to setup a HIGH security link. As the same list is used to store both
the STK's and the LTK's the type field is used so we can separate
between those two types of keys and if the key should be used when
in the master or slave role.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Every command handler of mgmt does a cast to the command structure
so it can properly interpreted. So we can avoid that cast if we
make those functions receive a void * directly.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fixes possible bug when deleting element from the list in
function hci_chan_list_flush. list_for_each_entry_rcu is used
and after deleting element from the list we also free pointer
and then list_entry_rcu is taken from freed pointer.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch implements the Cancel Pair Device command for mgmt. It's used
by user space to cancel an ongoing pairing attempt which was triggered
by the Pair Device command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes clearing of HCI_LINK_KEYS and HCI_DEBUG_KEYS
dev_flags while resetting. Without this patch pairing does
not work over management interface for BR-EDR devices.
Signed-off-by: Hemant Gupta <hemant.gupta@stericsson.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch sends correct IO Capability response to remote device
in case Local Device supports KeyBoardDisplay IO Capability as
this capability is not valid as per BT spec for IO capability
Request Reply Command.
This capability is mapped to DisplayYesNo which is in accordance
with BT spec.
Signed-off-by: Hemant Gupta <hemant.gupta@stericsson.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Commit 330605423c fixed l2cap conn establishment for non-ssp remote
devices by not setting HCI_CONN_ENCRYPT_PEND every time conn security
is tested (which was always returning failure on any subsequent
security checks).
However, this broke l2cap conn establishment for ssp remote devices
when an ACL link was already established at SDP-level security. This
fix ensures that encryption must be pending whenever authentication
is also pending.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We only should try to free the SMP channel that was created if there
is a pending SMP session.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is an imbalance in the rfcomm_session_hold / rfcomm_session_put
operations which causes the following crash:
[ 685.010159] BUG: unable to handle kernel paging request at 6b6b6b6b
[ 685.010169] IP: [<c149d76d>] rfcomm_process_dlcs+0x1b/0x15e
[ 685.010181] *pdpt = 000000002d665001 *pde = 0000000000000000
[ 685.010191] Oops: 0000 [#1] PREEMPT SMP
[ 685.010247]
[ 685.010255] Pid: 947, comm: krfcommd Tainted: G C 3.0.16-mid8-dirty #44
[ 685.010266] EIP: 0060:[<c149d76d>] EFLAGS: 00010246 CPU: 1
[ 685.010274] EIP is at rfcomm_process_dlcs+0x1b/0x15e
[ 685.010281] EAX: e79f551c EBX: 6b6b6b6b ECX: 00000007 EDX: e79f40b4
[ 685.010288] ESI: e79f4060 EDI: ed4e1f70 EBP: ed4e1f68 ESP: ed4e1f50
[ 685.010295] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 685.010303] Process krfcommd (pid: 947, ti=ed4e0000 task=ed43e5e0 task.ti=ed4e0000)
[ 685.010308] Stack:
[ 685.010312] ed4e1f68 c149eb53 e5925150 e79f4060 ed500000 ed4e1f70 ed4e1f80 c149ec10
[ 685.010331] 00000000 ed43e5e0 00000000 ed4e1f90 ed4e1f9c c149ec87 0000bf54 00000000
[ 685.010348] 00000000 ee03bf54 c149ec37 ed4e1fe4 c104fe01 00000000 00000000 00000000
[ 685.010367] Call Trace:
[ 685.010376] [<c149eb53>] ? rfcomm_process_rx+0x6e/0x74
[ 685.010387] [<c149ec10>] rfcomm_process_sessions+0xb7/0xde
[ 685.010398] [<c149ec87>] rfcomm_run+0x50/0x6d
[ 685.010409] [<c149ec37>] ? rfcomm_process_sessions+0xde/0xde
[ 685.010419] [<c104fe01>] kthread+0x63/0x68
[ 685.010431] [<c104fd9e>] ? __init_kthread_worker+0x42/0x42
[ 685.010442] [<c14dae82>] kernel_thread_helper+0x6/0xd
This issue has been brought up earlier here:
https://lkml.org/lkml/2011/5/21/127
The issue appears to be the rfcomm_session_put in rfcomm_recv_ua. This
operation doesn't seem be to required as for the non-initiator case we
have the rfcomm_process_rx doing an explicit put and in the initiator
case the last dlc_unlink will drive the reference counter to 0.
There have been several attempts to fix these issue:
6c2718d Bluetooth: Do not call rfcomm_session_put() for RFCOMM UA on closed socket
683d949 Bluetooth: Never deallocate a session when some DLC points to it
but AFAICS they do not fix the issue just make it harder to reproduce.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Gopala Krishna Murala <gopala.krishna.murala@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This function is not called in interrupt context anymore, so it
should use GFP_KERNEL to allocate memory.
Signed-off-by: Andre Guedes <aguedespe@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This makes clear that this is the size of the key used to
encrypt the link.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We need to use the _sync() version for cancelling the info and security
timer in the L2CAP connection delete path. Otherwise the delayed work
handler might run after the connection object is freed.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
__cancel_delayed_work() is being used in some paths where we cannot
sleep waiting for the delayed work to finish. However, that function
might return while the timer is running and the work will be queued
again. Replace the calls with safer cancel_delayed_work() version
which spins until the timer handler finishes on other CPUs and
cancels the delayed work.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We don't need locking hdev in hci_conn_timeout() since it doesn't
access any hdev's shared resources, it basically queues HCI commands.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This function is called in process context only, so it should use
GFP_KERNEL to allocate memory.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This function is called in process context only, so it should use
GFP_KERNEL to allocate memory.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It is not used outside of l2cap_core.c. Also l2cap_ertm_data_rcv is
only used after it is defined so there is no need for forward declaration.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It's a very common test to see if both the local and the remote device
have SSP enabled. By creating a simple function to test this we can
shorten many if-statements in the code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The ssp_mode is essentially just a boolean so it's more appropriate to
have it simply as a flag in hdev->dev_flags.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Now that the flags member of struct hci_conn is supposed to accommodate
any boolean type values we can easily merge all boolean members into it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch updates mgmt_ev_device_connected and mgmt_ev_device found to
include an EIR-encoded remote name and class whenever possible. With
this addition the mgmt_ev_remote_name event becomes unnecessary and can
be removed. Since the connected event doesn't map to hci_conn_complete
anymore a HCI_CONN_MGMT_CONNECTED flag is added to track when mgmt has
been notified about a connection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The hdev->out variable is essentially a boolean so the type 'bool' makes
more sense than u8.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
These flags can and will be used for more general purpose values than
just pending state transitions so the more common name "flags" makes
more sense than "pend".
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
There's no need to have a separate device class field since the same
information can be encoded into the EIR data.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This makes the function accessible from all places it's needed (e.g.
mgmt.c and hci_event.c).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This allows for other uses such as checking for an embedded class of
device value in order to decide whether to append the class or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch add a two byte eir_len parameter mgmt_ev_device_found. Since
it's unlikely that the data will in the short term be much bigger than
conventional EIR lengths just use a small stack based buffer for now to
avoid dynamic memory allocation & freeing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
User space uses device_(dis)connected instead of just (dis)connected so
rename the defines and functions to match this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
There are several other dev_flags besided HCI_MGMT that should not be
cleared upon reset.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Devices found during LE scan should be reported to userspace through
mgmt_device_found events.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds a new parameter to mgmt_device_found() to inform
the length of 'eir' pointer.
EIR data from LE advertising report event doesn't have a fixed length
as EIR data from extended inquiry result event does. We needed to
change mgmt_device_found() so it copies 'eir_len' bytes instead of
HCI_MAX_EIR_LENGTH.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Remove unneeded conversion from sk to chan.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Reference counter was incremented when starting ack timer but
decremented only when clearing timer, not when timer fired.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is no need to send RNR immediately when entring local busy.
Also upper layer might clear local busy condition before ack timer
expires saving few cycles for sending RNR.
This also prevents sending two RNRs in some cases where sending one
would be enough i.e received N I-frame can trigger local busy
(sending RNR acking up to N-1 I-frame) and later sending ack (RNR
acking up to N I-frame).
This was affecting TC_ERM_BV_07_C and TC_ERM_BV_22_C with some non
default channel parameters (tx window and receiving buffer sizes).
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
ack_timer should be cleared when sending ACK to avoid acking I-frames
twice.
This commit introduces helper function (only send ack, not clearing
timer) which is used by l2cap_send_ack and l2cap_ack_timeout. This is
to avoid clearing ack timer in timer function.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
SREJ frame with P-bit set acknowledges I-frames numbered up to
(ReqSeq - 1). With this patch P-bit in SREJ is set only when there are
some I-frames to ack.
This fixes ambiguous situation when lost of I-frame with TxSeq=0 would
result in sending SREJ acking all previous I-frames.
Consider following scenario:
TxWindow=3
HostA: sent I-frame TxSeq=0
HostA: sent I-frame TxSeq=1
HostA: sent I-frame TxSeq=2
HostB: missed I-frame TxSeq=0
HostB: received I-frame TxSeq=1
HostB: sent SREJ ReqSeq=0 Pbit=1
HostA: received SREJ ReqSeq=0 Pbit=1 <- All I-frames acked or not?
...
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fix the following build warning:
CC [M] net/bluetooth/hci_core.o
net/bluetooth/hci_core.c: In function ‘__check_enable_hs’:
net/bluetooth/hci_core.c:2587: warning: return from incompatible pointer type
module_param in hci_core.c passes 'enable_hs' as bool format, so fix
this variable definition type.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch makes sure that devices with stronger signal (RSSI closer to
0) are sorted first in the resolve list and will therefore get their
names resolved first during device discovery. Since it's more likely
that the device the user is trying to discover has a strong signal due
to its proximity this ensures that the user gets the "device found"
event for it more quickly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The HCI_MGMT flag should not be cleared when resetting a HCI device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
There's no point in exposing these to user-space (which is what happens
to everything in hdev->flags) so move them to dev_flags instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
As reported by Dan Carpenter this function causes a Sparse warning and
shouldn't be declared inline:
include/net/bluetooth/l2cap.h:837:30 error: marked inline, but without a
definition"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Since we remove the owner field of hci_dev hci_dev_put and __hci_dev_put
do the same so we can merge them into one function. Same for
hci_dev_hold and __hci_dev_hold.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hci_dev->dev device structure has an internal refcount. This
refcount is used to protect the whole hci_dev object. However, we
currently do not use it. Therefore, if someone calls hci_free_dev() we
currently immediately destroy the hci_dev object because we never took
the device refcount.
This even happens if the hci_dev->refcnt is not 0. In fact, the
hci_dev->refcnt is totally useless in its current state. Therefore, we
simply remove hci_dev->refcnt and instead use hci_dev->dev refcnt.
This fixes all the symptoms and also correctly integrates the device
structure into our bluetooth bus system.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
After unregistering an hci_dev object a bluetooth driver does not have
any callbacks in the hci_dev structure left over. Therefore, there is no
need to keep a reference to the module.
Previously, we needed this to protect the hci-destruct callback.
However, this callback is no longer available so we do not need this
owner field, anymore. Drivers now call hci_unregister_dev() and they
are done with the object.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We provide a device-object to other subsystems and we provide our own
release-function. Therefore, the device-object must own a reference to
our module, otherwise the release-function may get deleted before the
device-object does.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Several drivers already provide an empty callback so we can actually
make this optional and then remove all those empty callbacks in the
drivers.
This callback isn't needed at all by most drivers as they can remove
their allocated structures on device disconnect and not on hci
destruction.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Adds HCI_ACL_TX_TIMEOUT and clear conversion from msec to jiffies
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
After moving L2CAP timers to workqueues l2cap_set_timer expects timeout
value to be specified in jiffies but constants defined in miliseconds
are used. This makes timeouts unreliable when CONFIG_HZ is not set to
1000.
__set_chan_timer macro still uses jiffies as input to avoid multiple
conversions from/to jiffies for sk_sndtimeo value which is already
specified in jiffies.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Ackec-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
sk_sndtime value should be specified in jiffies thus initial value
needs to be converted from miliseconds. Otherwise this timeout is
unreliable when CONFIG_HZ is not set to 1000.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Adds support for Number Of Completed Data Blocks Event.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds the necessary logic to perform name lookups after
inquiry completes. This is done by checking for entries in the resolve
list after each inquiry complete and remote name complete HCI event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds proper state tracking to the device discovery process.
This makes it possible to return appropriate errors when trying to stop
a non-active discovery or start discovery when it is already ongoing.
Once name resolving is implemented this also makes it possible to know
what the right action to do is when a remote name lookup is cancelled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This struct is used for not just inquiry caching but also for general
device discovery state tracking so it's better to rename it to something
more appropriate.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
For the remote name state tracking for the management interface to work
the cache needs to be flushed whenever inquiry is started. The
hci_do_inquiry function is only used by the management interface so by
having the flushing done from it ensures that old ioctl based
functionality isn't affected.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
If user-space has already confirmed the name for a remote device we
shouldn't request confirmation again. The simplest way to do this is to
return the name state from hci_inquiry_cache_update (if it is anything
else than unknown then we do not need confirmation from user-space).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds initial support for mgmt_confirm_name. It adds the
necessary tracking of the name state by extending the inquiry cache. The
actual name resolving operation (to be done once inquiry is finished) is
not yet part of this patch.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The EIR defines are needed also outside of mgmt.c (e.g. in hci_event.c
to check if EIR data has the complete name) so it's better to have them
in a single public place, i.e. hci.h.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This makes it possible to use the convenience functions provided for
standard kernel list types and it also makes it easier to extend the use
of the cache for the management interface where e.g. name resolving
control will be needed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Fix the newly-SACKed range to be the range of newly-shifted bytes.
Previously - since 832d11c5cd -
tcp_shifted_skb() incorrectly called tcp_sacktag_one() with the start
and end sequence numbers of the skb it passes in set to the range just
beyond the range that is newly-SACKed.
This commit also removes a special-case adjustment to lost_cnt_hint in
tcp_shifted_skb() since the pre-existing adjustment of lost_cnt_hint
in tcp_sacktag_one() now properly handles this things now that the
correct start sequence number is passed in.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit allows callers of tcp_sacktag_one() to pass in sequence
ranges that do not align with skb boundaries, as tcp_shifted_skb()
needs to do in an upcoming fix in this patch series.
In fact, now tcp_sacktag_one() does not need to depend on an input skb
at all, which makes its semantics and dependencies more clear.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If eth_mac_addr() get called, usually if SIOCSIFHWADDR was
used to change the MAC of a ethernet device, reset the
addr_assign_type to NET_ADDR_PERM if the state was
NET_ADDR_RANDOM before. Reset the state since the MAC is
no longer random at least not from the kernel side.
v2: changed to bitops, removed if()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, it is not easily possible to get TOS/DSCP value of packets from
an incoming TCP stream. The mechanism is there, IP_PKTOPTIONS getsockopt
with IP_RECVTOS set, the same way as incoming TTL can be queried. This is
not actually implemented for TOS, though.
This patch adds this functionality, both for IPv4 (IP_PKTOPTIONS) and IPv6
(IPV6_2292PKTOPTIONS). For IPv4, like in the IP_RECVTTL case, the value of
the TOS field is stored from the other party's ACK.
This is needed for proxies which require DSCP transparency. One such example
is at http://zph.bratcheda.org/.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement helper inline function to get traffic class from IPv6 header.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoth David:
1) GRO MAC header comparisons were ethernet specific, breaking other
link types. This required a multi-faceted fix to cure the originally
noted case (Infiniband), because IPoIB was lying about it's actual
hard header length. Thanks to Eric Dumazet, Roland Dreier, and
others.
2) Fix build failure when INET_UDP_DIAG is built in and ipv6 is modular.
From Anisse Astier.
3) Off by ones and other bug fixes in netprio_cgroup from Neil Horman.
4) ipv4 TCP reset generation needs to respect any network interface
binding from the socket, otherwise route lookups might give a
different result than all the other segments received. From Shawn
Lu.
5) Fix unintended regression in ipv4 proxy ARP responses, from Thomas
Graf.
6) Fix SKB under-allocation bug in sh_eth, from Yoshihiro Shimoda.
7) Revert skge PCI mapping changes that are causing crashes for some
folks, from Stephen Hemminger.
8) IPV4 route lookups fill in the wildcarded fields of the given flow
lookup key passed in, which is fine most of the time as this is
exactly what the caller's want. However there are a few cases that
want to retain the original flow key values afterwards, so handle
those cases properly. Fix from Julian Anastasov.
9) IGB/IXGBE VF lookup bug fixes from Greg Rose.
10) Properly null terminate filename passed to ethtool flash device
method, from Ben Hutchings.
11) S3 resume fix in via-velocity from David Lv.
12) Fix double SKB free during xmit failure in CAIF, from Dmitry
Tarnyagin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
net: Don't proxy arp respond if iif == rt->dst.dev if private VLAN is disabled
ipv4: Fix wrong order of ip_rt_get_source() and update iph->daddr.
netprio_cgroup: fix wrong memory access when NETPRIO_CGROUP=m
netprio_cgroup: don't allocate prio table when a device is registered
netprio_cgroup: fix an off-by-one bug
bna: fix error handling of bnad_get_flash_partition_by_offset()
isdn: type bug in isdn_net_header()
net: Make qdisc_skb_cb upper size bound explicit.
ixgbe: ethtool: stats user buffer overrun
ixgbe: dcb: up2tc mapping lost on disable/enable CEE DCB state
ixgbe: do not update real num queues when netdev is going away
ixgbe: Fix broken dependency on MAX_SKB_FRAGS being related to page size
ixgbe: Fix case of Tx Hang in PF with 32 VFs
ixgbe: fix vf lookup
igb: fix vf lookup
e1000: add dropped DMA receive enable back in for WoL
gro: more generic L2 header check
IPoIB: Stop lying about hard_header_len and use skb->cb to stash LL addresses
zd1211rw: firmware needs duration_id set to zero for non-pspoll frames
net: enable TC35815 for MIPS again
...
Commit 653241 (net: RFC3069, private VLAN proxy arp support) changed
the behavior of arp proxy to send arp replies back out on the interface
the request came in even if the private VLAN feature is disabled.
Previously we checked rt->dst.dev != skb->dev for in scenarios, when
proxy arp is enabled on for the netdevice and also when individual proxy
neighbour entries have been added.
This patch adds the check back for the pneigh_lookup() scenario.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix a bug which introduced by commit ac8a4810 (ipv4: Save
nexthop address of LSRR/SSRR option to IPCB.).In that patch, we saved
the nexthop of SRR in ip_option->nexthop and update iph->daddr until
we get to ip_forward_options(), but we need to update it before
ip_rt_get_source(), otherwise we may get a wrong src.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the netprio_cgroup module is not loaded, net_prio_subsys_id
is -1, and so sock_update_prioidx() accesses cgroup_subsys array
with negative index subsys[-1].
Make the code resembles cls_cgroup code, which is bug free.
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
So we delay the allocation till the priority is set through cgroup,
and this makes skb_update_priority() faster when it's not set.
This also eliminates an off-by-one bug similar with the one fixed
in the previous patch.
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
# mount -t cgroup xxx /mnt
# mkdir /mnt/tmp
# cat /mnt/tmp/net_prio.ifpriomap
lo 0
eth0 0
virbr0 0
# echo 'lo 999' > /mnt/tmp/net_prio.ifpriomap
# cat /mnt/tmp/net_prio.ifpriomap
lo 999
eth0 0
virbr0 4101267344
We got weired output, because we exceeded the boundary of the array.
We may even crash the kernel..
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
read_lock(&tpt_trig->trig.leddev_list_lock) is accessed via the path
ieee80211_open (->) ieee80211_do_open (->) ieee80211_mod_tpt_led_trig
(->) ieee80211_start_tpt_led_trig (->) tpt_trig_timer before initializing
it.
the intilization of this read/write lock happens via the path
ieee80211_led_init (->) led_trigger_register, but we are doing
'ieee80211_led_init' after 'ieeee80211_if_add' where we
register netdev_ops.
so we access leddev_list_lock before initializing it and causes the
following bug in chrome laptops with AR928X cards with the following
script
while true
do
sudo modprobe -v ath9k
sleep 3
sudo modprobe -r ath9k
sleep 3
done
BUG: rwlock bad magic on CPU#1, wpa_supplicant/358, f5b9eccc
Pid: 358, comm: wpa_supplicant Not tainted 3.0.13 #1
Call Trace:
[<8137b9df>] rwlock_bug+0x3d/0x47
[<81179830>] do_raw_read_lock+0x19/0x29
[<8137f063>] _raw_read_lock+0xd/0xf
[<f9081957>] tpt_trig_timer+0xc3/0x145 [mac80211]
[<f9081f3a>] ieee80211_mod_tpt_led_trig+0x152/0x174 [mac80211]
[<f9076a3f>] ieee80211_do_open+0x11e/0x42e [mac80211]
[<f9075390>] ? ieee80211_check_concurrent_iface+0x26/0x13c [mac80211]
[<f9076d97>] ieee80211_open+0x48/0x4c [mac80211]
[<812dbed8>] __dev_open+0x82/0xab
[<812dc0c9>] __dev_change_flags+0x9c/0x113
[<812dc1ae>] dev_change_flags+0x18/0x44
[<8132144f>] devinet_ioctl+0x243/0x51a
[<81321ba9>] inet_ioctl+0x93/0xac
[<812cc951>] sock_ioctl+0x1c6/0x1ea
[<812cc78b>] ? might_fault+0x20/0x20
[<810b1ebb>] do_vfs_ioctl+0x46e/0x4a2
[<810a6ebb>] ? fget_light+0x2f/0x70
[<812ce549>] ? sys_recvmsg+0x3e/0x48
[<810b1f35>] sys_ioctl+0x46/0x69
[<8137fa77>] sysenter_do_call+0x12/0x2
Cc: <stable@vger.kernel.org>
Cc: Gary Morain <gmorain@google.com>
Cc: Paul Stewart <pstew@google.com>
Cc: Abhijit Pradhan <abhijit@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When trying to nf_queue GRO/GSO skbs, nf_queue uses skb_gso_segment
to split the skb.
However, if nf_queue is called via bridge netfilter, the mac header
won't be preserved -- packets will thus contain a bogus mac header.
Fix this by setting skb->data to the mac header when skb->nf_bridge
is set and restoring skb->data afterwards for all segments.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Just like skb->cb[], so that qdisc_skb_cb can be encapsulated inside
of other data structures.
This is intended to be used by IPoIB so that it can remember
addressing information stored at hard_header_ops->create() time that
it can fetch when the packet gets to the transmit routine.
Signed-off-by: David S. Miller <davem@davemloft.net>
For HS transport the maximum message size depends on the MTU-size
of the HS-device bound to the AF_IUCV socket. This patch adds a
getsockopt option MSGSIZE returning the maximum message size that
can be handled for this AF_IUCV socket.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch saves the net_device in the iucv_sock structure during
bind in order to fasten skb sending.
In addition some other small improvements are made for HS transport:
- error checking when sending skbs
- locking changes in afiucv_hs_callback_txnotify
- skb freeing in afiucv_hs_callback_txnotify
And finally it contains code cleanup to get rid of iucv_skb_queue_purge.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When polling on an AF_IUCV socket, writing should be blocked if the
number of pending messages exceeds a defined limit.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A SEVER is missing in the callback of a receiving SEVERED. This may
inhibit z/VM to remove the corresponding IUCV-path completely.
This patch adds a SEVER in iucv_callback_connrej (together with
additional locking.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shlomo Pongratz reported GRO L2 header check was suited for Ethernet
only, and failed on IB/ipoib traffic.
He provided a patch faking a zeroed header to let GRO aggregates frames.
Roland Dreier, Herbert Xu, and others suggested we change GRO L2 header
check to be more generic, ie not assuming L2 header is 14 bytes, but
taking into account hard_header_len.
__napi_gro_receive() has special handling for the common case (Ethernet)
to avoid a memcmp() call and use an inline optimized function instead.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Shlomo Pongratz <shlomop@mellanox.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most rate control implementations assume .get_rate and .tx_status are only
called once the per-station data has been fully initialized.
minstrel_ht crashes if this assumption is violated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IPV6_UNICAST_IF feature is the IPv6 compliment to IP_UNICAST_IF.
Signed-off-by: Erich E. Hoover <ehoover@mines.edu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP_UNICAST_IF feature is needed by the Wine project. This patch
implements the feature by setting the outgoing interface in a similar
fashion to that of IP_MULTICAST_IF. A separate option is needed to
handle this feature since the existing options do not provide all of
the characteristics required by IP_UNICAST_IF, a summary is provided
below.
SO_BINDTODEVICE:
* SO_BINDTODEVICE requires administrative privileges, IP_UNICAST_IF
does not. From reading some old mailing list articles my
understanding is that SO_BINDTODEVICE requires administrative
privileges because it can override the administrator's routing
settings.
* The SO_BINDTODEVICE option restricts both outbound and inbound
traffic, IP_UNICAST_IF only impacts outbound traffic.
IP_PKTINFO:
* Since IP_PKTINFO and IP_UNICAST_IF are independent options,
implementing IP_UNICAST_IF with IP_PKTINFO will likely break some
applications.
* Implementing IP_UNICAST_IF on top of IP_PKTINFO significantly
complicates the Wine codebase and reduces the socket performance
(doing this requires a lot of extra communication between the
"server" and "user" layers).
bind():
* bind() does not work on broadcast packets, IP_UNICAST_IF is
specifically intended to work with broadcast packets.
* Like SO_BINDTODEVICE, bind() restricts both outbound and inbound
traffic.
Signed-off-by: Erich E. Hoover <ehoover@mines.edu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shlomo Pongratz reported GRO L2 header check was suited for Ethernet
only, and failed on IB/ipoib traffic.
He provided a patch faking a zeroed header to let GRO aggregates frames.
Roland Dreier, Herbert Xu, and others suggested we change GRO L2 header
check to be more generic, ie not assuming L2 header is 14 bytes, but
taking into account hard_header_len.
__napi_gro_receive() has special handling for the common case (Ethernet)
to avoid a memcmp() call and use an inline optimized function instead.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Shlomo Pongratz <shlomop@mellanox.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If you want to use mesh support from mac80211 on a recent
kernel on 2.6.24 you'll run into a name clash when compiling
against include/linux/namei.h, so rename this routine.
/home/mcgrof/tmp/compat-wireless-3.2.5-1/net/mac80211/mesh_pathtbl.c: At top level:
/home/mcgrof/tmp/compat-wireless-3.2.5-1/net/mac80211/mesh_pathtbl.c:342:26: error: conflicting types for ‘path_lookup’
include/linux/namei.h:71:12: note: previous declaration of ‘path_lookup’ was here
Although this could sit as a separate patch in compat-wireless it seems
best to just merge upstream.
Cc: Javier Cardona <javier@cozybit.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@frijolero.org>
Acked-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When not debugging mac80211 code, station state transitions do not need to
show up in the kernel log.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"priv" is initialized twice. I kept the second one, because it is next
to the check for NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qdisc supports two operations - plug and unplug. When the
qdisc receives a plug command via netlink request, packets arriving
henceforth are buffered until a corresponding unplug command is received.
Depending on the type of unplug command, the queue can be unplugged
indefinitely or selectively.
This qdisc can be used to implement output buffering, an essential
functionality required for consistent recovery in checkpoint based
fault-tolerance systems. Output buffering enables speculative execution
by allowing generated network traffic to be rolled back. It is used to
provide network protection for Xen Guests in the Remus high availability
project, available as part of Xen.
This module is generic enough to be used by any other system that wishes
to add speculative execution and output buffering to its applications.
This module was originally available in the linux 2.6.32 PV-OPS tree,
used as dom0 for Xen.
For more information, please refer to http://nss.cs.ubc.ca/remus/
and http://wiki.xensource.com/xenwiki/Remus
Changes in V3:
* Removed debug output (printk) on queue overflow
* Added TCQ_PLUG_RELEASE_INDEFINITE - that allows the user to
use this qdisc, for simple plug/unplug operations.
* Use of packet counts instead of pointers to keep track of
the buffers in the queue.
Signed-off-by: Shriram Rajagopalan <rshriram@cs.ubc.ca>
Signed-off-by: Brendan Cully <brendan@cs.ubc.ca>
[author of the code in the linux 2.6.32 pvops tree]
Signed-off-by: David S. Miller <davem@davemloft.net>
We check "task->tk_rqstp" and then we dereference it without checking on
the next line. The only caller is call_connect() and that has a check
which prevents it from calling xprt_connect() with a NULL.
if (task->tk_status < 0)
return;
If "task->tk_rqstp" were NULL then "tk_status" would be -EAGAIN.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Modifies message rejection logic so that TIPC doesn't attempt to
send a FIN message to the rejecting port if it is known in advance
that there is no such message because the rejecting port doesn't exist.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removes code that alters the publication key of a name table entry
that is being forcibly purged from TIPC's name table after contact
with the publishing node has been lost.
Current TIPC ensures that all defunct names are purged before
re-establishing contact with a failed node. There used to be a risk
that the publication might be accidentally deleted because it might be
re-added to the name table before the purge operation was completed.
But now there is no longer a need to ensure that the new key is different
than the old one.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies broadcast link so that an incoming fragmented message is not
lost if reassembly cannot begin because there currently is no buffer
big enough to hold the entire reassembled message. The broadcast link
now ignores the first fragment completely, which causes the sending node
to retransmit the first fragment so that reassembly can be re-attempted.
Previously, the sender would have had no reason to retransmit the 1st
fragment, so we would never have a chance to re-try the allocation.
To do this cleanly without duplicaton, a new bclink_accept_pkt()
function is introduced.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies unicast link endpoint logic so an incoming fragmented message
is not lost if reassembly cannot begin because there is no buffer big
enough to hold the entire reassembled message. The link endpoint now
ignores the first fragment completely, which causes the sending node to
retransmit the first fragment so that reassembly can be re-attempted.
Previously, the sender would have had no reason to retransmit the 1st
fragment, so we would never have a chance to re-try the allocation.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Eliminates support for the broadcast tag field, which is no longer
used by broadcast link NACK messages.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Completely redesigns broadcast link ACK and NACK mechanisms to prevent
spurious retransmit requests in dual LAN networks, and to prevent the
broadcast link from stalling due to the failure of a receiving node to
acknowledge receiving a broadcast message or request its retransmission.
Note: These changes only impact the timing of when ACK and NACK messages
are sent, and not the basic broadcast link protocol itself, so inter-
operability with nodes using the "classic" algorithms is maintained.
The revised algorithms are as follows:
1) An explicit ACK message is still sent after receiving 16 in-sequence
messages, and implicit ACK information continues to be carried in other
unicast link message headers (including link state messages). However,
the timing of explicit ACKs is now based on the receiving node's absolute
network address rather than its relative network address to ensure that
the failure of another node does not delay the ACK beyond its 16 message
target.
2) A NACK message is now typically sent only when a message gap persists
for two consecutive incoming link state messages; this ensures that a
suspected gap is not confirmed until both LANs in a dual LAN network have
had an opportunity to deliver the message, thereby preventing spurious NACKs.
A NACK message can also be generated by the arrival of a single link state
message, if the deferred queue is so big that the current message gap
cannot be the result of "normal" mis-ordering due to the use of dual LANs
(or one LAN using a bonded interface). Since link state messages typically
arrive at different nodes at different times the problem of multiple nodes
issuing identical NACKs simultaneously is inherently avoided.
3) Nodes continue to "peek" at NACK messages sent by other nodes. If
another node requests retransmission of a message gap suspected (but not
yet confirmed) by the peeking node, the peeking node forgets about the
gap and does not generate a duplicate retransmit request. (If the peeking
node subsequently fails to receive the lost message, later link state
messages will cause it to rediscover and confirm the gap and send another
NACK.)
4) Message gap "equality" is now determined by the start of the gap only.
This is sufficient to deal with the most common cases of message loss,
and eliminates the need for complex end of gap computations.
5) A peeking node no longer tries to determine whether it should send a
complementary NACK, since the most common cases of message loss don't
require it to be sent. Consequently, the node no longer examines the
"broadcast tag" field of a NACK message when peeking.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensures that all attempts to update broadcast link statistics are done
only while holding the lock that protects the link's main data structures,
to prevent interference by simultaneous updates caused by messages
arriving on other interfaces.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies broadcast link so that it increments the "received duplicate
message" count if an incoming message cannot be added to the deferred
message queue because it is already present in the queue. (The aligns
broadcast link behavior with that of TIPC's unicast links.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Fixes a pair of problems in broadcast link message reception code
relating to the reclamation of the node lock after consuming an
in-sequence message.
1) Now retests to see if the sending node is still up after reclaiming
the node lock, and bails out if it is non-operational.
2) Now manipulates the node's deferred message queue only after
reclaiming the node lock, rather than using queue head pointer
information that was cached previously.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensures that any attempt to send a NACK message over TIPC's broadcast
link has exclusive access to the link's main data structures, to prevent
interference with a simultaneous attempt to send other broadcast link
traffic (such as application-generated multicast messages).
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Corrects a problem in which a link endpoint that activates as the
result of receiving a RESET/STATE sequence of link protocol messages
fails to properly record the broadcast link status information about
the node to which it is now communicating with. (The problem does
not occur with the more common RESET/ACTIVATE sequence of messages.)
The fix ensures that the broadcast link status info is updated after
the RESET message resets the link endpoint, rather than before, thereby
preventing new information from being overwritten by the reset operation.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Fix a bug that can prevent TIPC from sending broadcast messages to a node
if contact with the node is lost and then regained. The problem occurs if
the broadcast link first clears the flag indicating the node is part of the
link's distribution set (when it loses contact with the node), and later
fails to restore the flag (when contact is regained); restoration fails
if contact with the node is regained by implicit unicast link activation
triggered by the arrival of a data message, rather than explicitly by the
arrival of a link activation message.
The broadcast link now uses separate fields to track whether a node is
theoretically capable of receiving broadcast messages versus whether it is
actually part of the link's distribution set. The former member is updated
by the receipt of link protocol messages, which can occur at any time; the
latter member is updated only when contact with the node is gained or lost.
This change also permits the simplification of several conditional
expressions since the broadcast link's "supported" field can now only be
set if there are working links to the associated node.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensure that sequence number information about incoming broadcast link
messages is initialized only by the activation of the first link to a
given cluster node. Previously, a race condition allowed reset and/or
activation messages for a second link to re-initialize this sequence
number information with obsolete values. This could trigger TIPC to
request the retransmission of previously acknowledged broadcast link
messages from that node, resulting in broadcast link processing becoming
stalled if the node had already released one or more of those messages
and was unable to perform the required retransmission.
Thanks to Laser <gotolaser@gmail.com> for identifying this problem
and assisting in the development of this fix.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensures that a link endpoint discards any previously deferred link
protocol message whenever it attempts to send a new one.
Previously, it was possible for a link protocol message that was unsent
due to congestion to be transmitted after newer protocol messages had
been sent. The stale link protocol message might then cause the receiving
link endpoint to malfunction because of its outdated conent.
Thanks to Osamu Kaminuma [okaminum@avaya.com] for diagnosing the problem
and contributing a prototype patch.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Re-code the algorithm for inserting an out-of-sequence message into
a unicast or broadcast link's deferred message queue. It remains
functionally equivalent but should be easier to understand/maintain.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
There are situations where we don't have the
necessary rate control information yet for
station entries, e.g. when associating. This
currently doesn't really happen due to the
dummy station handling; explicitly disabling
rate control when it's not initialised will
allow us to remove dummy stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just like skb->cb[], so that qdisc_skb_cb can be encapsulated inside
of other data structures.
This is intended to be used by IPoIB so that it can remember
addressing information stored at hard_header_ops->create() time that
it can fetch when the packet gets to the transmit routine.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mac80211 goes to idle-off before starting a scan.
However, some devices that implement hw scan might not
need going idle-off in order to perform a hw scan, and
thus saving some energy and simplifying their state machine.
(Note that this is also the case for sched scan - it
currently doesn't make mac80211 go idle-off)
Add a new flag to indicate support for hw scan while idle.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ridx" is used as an index into the mcs_mask[] array which has
IEEE80211_HT_MCS_MASK_LEN elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the IBSS network is RSN-protected, let userspace authorize the stations
instead of adding them as AUTHORIZED by default.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the second part of the auth/assoc redesign,
the mac80211 part. This moves the auth/assoc code
out of the work abstraction and into the MLME, so
that we don't flip channels all the time etc.
The only downside is that when we are associated,
we need to drop the association in order to create
a connection to another AP, but for most drivers
this is actually desirable and the ability to do
was never used by any applications. If we want to
implement resource reservation with FT-OTA, we'd
probably best do it with explicit R-O-C in wpa_s.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed by mac80211 to keep a reference
to a BSS alive for the auth process. Remove the
old version of cfg80211_ref_bss() since it's
not actually used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To track authenticated state seems to have been
a design mistake in cfg80211. It is possible to
have out of band authentication (FT), tracking
multiple authentications caused more problems
than it ever helped, and the implementation in
mac80211 is too complex.
Remove all this complexity, and let userspace
do whatever it wants to, mac80211 can deal with
that just fine. Association is still tracked of
course, but authentication no longer is. Local
auth state changes are thus no longer of value,
so ignore them completely.
This will also help implement SAE -- asking the
driver to do an authentication is now almost
equivalent to sending an authentication frame,
with the exception of shared key authentication
which is still handled completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The dummy STA support was added because I didn't
want to change the driver API at the time. Now
that we have state transitions triggering station
add/remove in the driver, we only call add once a
station reaches ASSOCIATED, so we can remove the
dummy station stuff again.
While at it, tighten the RX check and accept only
port control (EAP) frames from the AP station if
it's not associated yet -- in other cases there's
no race.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of maintaining separate sta_add/sta_remove
callsites, implement it in sta_state when the driver
has no sta_state implementation.
The only behavioural change this should cause is in
secure mesh mode: with this the station entries will
only be created after the stations are set to AUTH.
Given which drivers support mesh, this seems to not
be a problem.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(based on Eliad's patch)
Add a callback to notify the low-level driver whenever
the state of a station changes. The driver is only
notified when the station is actually in the mac80211
hash table, not for pre-insert state transitions.
To allow the driver to replace sta_add/remove calls
with this, call extra transitions with the NOTEXIST
state.
This callback can fail, so we need to be careful in
handling it when a station is inserted, particularly
in the IBSS case where we still keep the station entry
around for mac80211 purposes.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be used by drivers later if they
need to have stations inserted all the time,
in mac80211 has no purpose, is never used
and sta_state starts out in NONE.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a station couldn't be uploaded to the driver but
is still kept (only in IBSS mode) we still shouldn't
try to program the keys for it into hardware; fix
this bug by skipping the key upload in this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting keys and updating TKIP keys must use the
BSS sdata (not AP_VLAN), so we translate. Move
the translation into driver-ops wrappers instead
of having it inline in the code to simplify the
normal code flow.
The same can be done for sta_add/remove which
already does the translation in the wrapper.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the station state modification right before insert,
this just makes the current code more readable (you can
tell that it's before insertion looking at a single
screenful of code) right now, but some upcoming changes
will require this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds three trace points to the status routines
in the sunrpc state machine.
The goal of these trace points is to give an Admin
the ability to check on binding status or connection
status to see if there is a potential problem.
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The variable 'neigh' is assigned to, but otherwise completely
unused. So let's remove it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Binding RST packet outgoing interface to incoming interface
for tcp v4 when there is no socket associate with it.
when sk is not NULL, using sk->sk_bound_dev_if instead.
(suggested by Eric Dumazet).
This has few benefits:
1. tcp_v6_send_reset already did that.
2. This helps tcp connect with SO_BINDTODEVICE set. When
connection is lost, we still able to sending out RST using
same interface.
3. we are sending reply, it is most likely to be succeed
if iif is used
Signed-off-by: Shawn Lu <shawn.lu@ericsson.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was recently pointed out to me that the get_prioidx function sets a bit in
the prioidx map prior to checking to see if the index being set is out of
bounds. This patch corrects that, avoiding the possiblity of us writing beyond
the end of the array
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
CC: Stanislaw Gruszka <sgruszka@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Count dropped packets in CAIF Netdevice.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill off the debug-fs exposed varaibles from caif_socket.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f11017ec2d (2.6.37)
moved the fwmark variable in subcontext that is invalidated before
reaching the ip_vs_ct_in_get call. As vaddr is provided as pointer
in the param structure make sure the fwmark variable is in
same context. As the fwmark templates can not be matched,
more and more template connections are created and the
controlled connections can not go to single real server.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Cc: stable@vger.kernel.org
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is a cleanup patch.
Service temporary sockets can be TCP or RDMA only. But XPT_CHNGBUF service
socket flag is checked only for UDP sockets on receive.
Thus (if I don't miss something non-obvious) this bit raising for temporary
sockets can be removed.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
We check for zero length strings in the caller now, so these aren't
needed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
There is no point in passing a zero length string here and quite a
few of that cache_parse() implementations will Oops if count is
zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: fix safety of rbd_put_client()
rbd: fix a memory leak in rbd_get_client()
ceph: create a new session lock to avoid lock inversion
ceph: fix length validation in parse_reply_info()
ceph: initialize client debugfs outside of monc->mutex
ceph: change "ceph.layout" xattr to be "ceph.file.layout"
Initializing debufs under monc->mutex introduces a lock dependency for
sb->s_type->i_mutex_key, which (combined with several other dependencies)
leads to an annoying lockdep warning. There's no particular reason to do
the debugfs setup under this lock, so move it out.
It used to be the case that our first monmap could come from the OSD; that
is no longer the case with recent servers, so we will reliably set up the
client entry during the initial authentication.
We don't have to worry about racing with debugfs teardown by
ceph_debugfs_client_cleanup() because ceph_destroy_client() calls
ceph_msgr_flush() first, which will wait for the message dispatch work
to complete (and the debugfs init to complete).
Fixes: #1940
Signed-off-by: Sage Weil <sage@newdream.net>
SKB is freed twice upon send error. The Network stack consumes SKB even
when it returns error code.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always use cfmuxl_remove_uplayer when removing a up-layer.
cfmuxl_ctrlcmd() can be called independently and in parallel with
cfmuxl_remove_uplayer(). The race between them could cause list_del_rcu
to be called on a node which has been already taken out from the list.
That lead to a (rare) crash on accessing poisoned node->prev inside
list_del_rcu.
This fix ensures that deletion are done holding the same lock.
Reported-by: Dmitry Tarnyagin <dmitry.tarnyagin@stericsson.com>
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4acb4190 tries to fix the using uninitialized value
introduced by commit 3dc43e3, but it would make the
per-socket memory limits too small.
This patch fixes this and also remove the redundant codes
introduced in 4acb4190.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Glauber Costa <glommer@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The argument is not used at all, and it's not necessary, because
a specific callback handler of course knows which subsys it
belongs to.
Now only ->pupulate() takes this argument, because the handlers of
this callback always call cgroup_add_file()/cgroup_add_files().
So we reduce a few lines of code, though the shrinking of object size
is minimal.
16 files changed, 113 insertions(+), 162 deletions(-)
text data bss dec hex filename
5486240 656987 7039960 13183187 c928d3 vmlinux.o.orig
5486170 656987 7039960 13183117 c9288d vmlinux.o
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
CLIP only support ipv4, and this is evidenced by the fact that it
is a device specific extension of arp_tbl, so this conversion is
pretty straightforward.
Signed-off-by: David S. Miller <davem@davemloft.net>
It went from unused, to commented out, and never changing after
that.
Just get rid of it, if someone wants it they can unearth it from
the history.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current logging style.
Coalesce formats where appropriate.
Update grammar where appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code checks for stored_mpdu_num > 1, causing
the reorder_timer to be triggered indefinitely, but the
frame is never timed-out (until the next packet is received)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Cc: <stable@vger.kernel.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The parameters for ETHTOOL_FLASHDEV include a filename, which ought to
be null-terminated. Currently the only driver that implements
ethtool_ops::flash_device attempts to add a null terminator if
necessary, but does it wrongly. Do it in the ethtool core instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of our machines were reporting:
TCP: too many of orphaned sockets
even when the number of orphaned sockets was well below the
limit.
We print a different message depending on whether we're out
of TCP memory or there are too many orphaned sockets.
Also move the check out of line and cleanup the messages
that were printed.
Signed-off-by: Arun Sharma <asharma@fb.com>
Suggested-by: Mohan Srinivasan <mohan@fb.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the types in the packet layout order.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more current message logging style.
Add pr_fmt to prefix dmesg output with "netpoll: "
Add macros to print np->name.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP RST mechanism is broken in TCP md5(RFC2385). When
connection is gone, md5 key is lost, sending RST
without md5 hash is deem to ignored by peer. This can
be a problem since RST help protocal like bgp to fast
recove from peer crash.
In most case, users of tcp md5, such as bgp and ldp,
have listener on both sides to accept connection from peer.
md5 keys for peers are saved in listening socket.
There are two cases in finding md5 key when connection is
lost:
1.Passive receive RST: The message is send to well known port,
tcp will associate it with listner. md5 key is gotten from
listener.
2.Active receive RST (no sock): The message is send to ative
side, there is no socket associated with the message. In this
case, finding listener from source port, then find md5 key from
listener.
we are not loosing sercuriy here:
packet is checked with md5 hash. No RST is generated
if md5 hash doesn't match or no md5 key can be found.
Signed-off-by: Shawn Lu <shawn.lu@ericsson.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't check for NULL consistently in __xfrm6_output(). If "x" were
NULL here it would lead to an OOPs later. I asked Steffen Klassert
about this and he suggested that we remove the NULL check.
On 10/29/11, Steffen Klassert <steffen.klassert@secunet.com> wrote:
>> net/ipv6/xfrm6_output.c
>> 148
>> 149 if ((x && x->props.mode == XFRM_MODE_TUNNEL) &&
>> ^
>
> x can't be null here. It would be a bug if __xfrm6_output() is called
> without a xfrm_state attached to the skb. I think we can just remove
> this null check.
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes sure we use appropriate memory barriers before
publishing tp->md5sig_info, allowing tcp_md5_do_lookup() being used from
tcp_v4_send_reset() without holding socket lock (upcoming patch from
Shawn Lu)
Note we also need to respect rcu grace period before its freeing, since
we can free socket without this grace period thanks to
SLAB_DESTROY_BY_RCU
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Shawn Lu <shawn.lu@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes this build error when CONFIG_NET_NS is not set:
net/sunrpc/svcsock.c: In function 'svc_setup_socket':
net/sunrpc/svcsock.c:1412:40: error: 'struct sock_common' has no member named 'skc_net'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Service transports are parametrized by network namespace. And thus lookup of
transport instance have to take network namespace into account.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: J. Bruce Fields <bfields@redhat.com>
This patch makes it possible to create NFSd program entry ("/proc/net/rpc/nfsd")
in passed network namespace context instead of hard-coded "init_net".
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch makes it possible to create NFS program entry ("/proc/net/rpc/nfs")
in passed network namespace context instead of hard-coded "init_net".
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
All cache users now uses network-namespace-aware routines, so generic ones
are obsolete.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: J. Bruce Fields <bfields@redhat.com>
This patch converts ip_map_cache per network namespace implemenetation to the
same view, as other caches done in the series.
Besides generalization, code becomes shorter with this patch.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: J. Bruce Fields <bfields@redhat.com>
This patch makes GSS auth cache details allocated and registered per network
namespace context.
Thus with this patch rsi_cache and rsc_cache contents for network namespace "X"
are controlled from proc file system mount for the same network namespace "X".
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: J. Bruce Fields <bfields@redhat.com>
v2:
1) fixed silly usage of template cache as a real one (this code left from
static global cache for all)
This patch makes unix_gid_cache cache detail allocated and registered per
network namespace context.
Thus with this patch unix_gid_cache contents for network namespace "X" are
controlled from proc file system mount for the same network namespace "X".
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: J. Bruce Fields <bfields@redhat.com>
This patch prepares infrastructure for network namespace aware cache detail
allocation.
One note about adding network namespace link to cache structure. It's going to
be used later in NFS DNS cache parsing routine (nfs_dns_parse for rpc_pton()
call).
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: J. Bruce Fields <bfields@redhat.com>
On service shutdown we can be sure, that no more users of it left except
current. Thus it looks like using current network namespace context is safe in
this case.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Service, using rpcbind (Lockd, NFSd) are starting from userspace call and thus
we can use current network namespace.
There could be a problem with NFSd service, because it's creation can be called
through NFSd fs from different network namespace. But this is a part of "NFSd
per net ns" task and will be fixed in future.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Lockd and NFSd services will handle requests from and to many network
nsamespaces. And thus have to be registered and unregistered per network
namespace.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Pass request socket network namespace to rpc_uaddr2sockaddr() instead of
hardcoded "init_net", when decoding address in RPCBPROC_GETADDR procedure.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Parametrize rpc_uaddr2sockaddr() by network context and thus force it's callers to pass
in network context instead of using hard-coded "init_net".
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Parametrize rpc_pton() by network context and thus force it's callers to pass
in network context instead of using hard-coded "init_net".
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Parametrize rpc_pton6() by network context and thus force it's caller
to pass in network context instead of using hard-coded "init_net".
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Parametrize rpc_parse_scope_id() by network context and thus force it's caller
to pass in network context instead of using hard-coded "init_net".
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
These client are per network namespace and thus can be created for different
network namespaces.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Registering rpcbind program requires rpcbind clients, which are per network
namespace context.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Rpcbind clients are per network namespace.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Static rpcbind registering functions can be parametrized by network namespace
pointer, calculated only once, instead of using init_net pointer (or taking it
from current when virtualization will be comleted) in many places.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Static rpcbind creation functions can be parametrized by network namespace
pointer, calculated only once, instead of using init_net pointer (or taking it
from current when virtualization will be comleted) in many places.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch makes rpcbind logic works in network namespace context. IOW each
network namespace will have it's own unique rpcbind internals (clients and
friends) required for registering svc services per network namespace.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We have to ensure that the wake up from the waitqueue and the assignment
of xprt->snd_task are atomic. We can do this by assigning the snd_task
while under the waitqueue spinlock.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch removes static rpc_mnt variable and its creation and destruction
routines, because they are not used anymore.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
v2:
1) Added "nfs_idmap_init" and "nfs_idmap_quit" definitions for kernels built
without CONFIG_NFS_V4 option set.
This patch subscribes NFS clients to RPC pipefs notifications. Idmap notifier
is registering on NFS module load. This notifier callback is responsible for
creation/destruction of PipeFS idmap pipe dentry for NFS4 clients.
Since ipdmap pipe is created in rpc client pipefs directory, we have make sure,
that this directory has been created already. IOW RPC client notifier callback
has been called already. To achive this, PipeFS notifier priorities has been
introduced (RPC clients notifier priority is greater than NFS idmap one).
But this approach gives another problem: unlink for RPC client directory will
be called before NFS idmap pipe unlink on UMOUNT event and will fail, because
directory is not empty.
The solution, introduced in this patch, is to try to remove client directory
once again after idmap pipe was unlinked. This looks like ugly hack, so
probably it should be replaced in some more elegant way.
Note that no locking required in notifier callback because PipeFS superblock
pointer is passed as an argument from it's creation or destruction routine and
thus we can be sure about it's validity.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch looks late due to GSS AUTH patches sent already. But it fixes a flaw
in RPC PipeFS pipes handling.
I've added this patch in the series, because this series related to pipes. But
it should be a part of previous series named "SUNPRC: cleanup PipeFS for
network-namespace-aware users".
Pipe dentry can be created and destroyed many times during pipe life cycle.
This actually means, that we can't set pipe->ops to NULL in rpc_close_pipes()
and use this variable as a flag, indicating, that pipe's dentry is unlinking.
To follow this restriction, this patch replaces "pipe->ops = NULL" assignment
and checks for NULL with "pipe->dentry = NULL" assignment and checks for
NULL respectively.
This patch also removes check for non-NULL pipe->ops (or pipe->dentry) in
rpc_close_pipes() because it always non-NULL now.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This precursor patch splits SUNRPC cache creation and PipeFS registartion.
It's required for latter split of NFS DNS resolver cache creation per network
namespace context and PipeFS registration/unregistration on MOUNT/UMOUNT
events.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This is a cleanup patch. We don't need this reference anymore.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
v2:
1) Updated due to changes in the first patch of the series.
Now, with RPC pipefs mount notifications handling in RPC clients, we can remove
mount point creation and destruction. RPC clients dentries will be created on
PipeFS mount event and removed on umount event.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Without this patch we have races:
rpc_fill_super rpc_free_client
rpc_pipefs_event(MOUNT) rpc_remove_pipedir
spin_lock(&rpc_client_lock);
rpc_setup_pipedir_sb
spin_unlock(&rpc_client_lock);
spin_lock(&rpc_client_lock);
(remove from list)
spin_unlock(&rpc_client_lock);
MEAMORY LEAKED
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch subscribes RPC clients to RPC pipefs notifications. RPC clients
notifier block is registering with pipefs initialization during SUNRPC module
init.
This notifier callback is responsible for RPC client PipeFS directory and GSS
pipes creation. For pipes creation and destruction two additional callbacks
were added to struct rpc_authops.
Note that no locking required in notifier callback because PipeFS superblock
pointer is passed as an argument from it's creation or destruction routine and
thus we can be sure about it's validity.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch moves static SUNRPC clients list and it's lock to sunrpc_net
structure.
Currently this list is used only for debug purposes. But later it will be used
also for selecting clients by networks namespace on PipeFS mount/umount events.
Per-network namespace lists will make this faster and simplier.
Note: client list is taken from "init_net" network namespace context in
rpc_show_tasks(). This will be changed some day later with making SUNRPC
sysctl's per network namespace context.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch makes RPC GSS PipeFs pipes allocated in it's RPC client owner
network namespace context.
Pipes creation and destruction now done in separated functions, which takes
care about PipeFS superblock locking.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
v2:
1) "Over-put" of PipeFS mount point fixed. Fix is ugly, but allows to bisect
the patch set. And it will be removed later in the series.
This patch makes RPC clients PipeFs dentries allocations in it's owner network
namespace context.
RPC client pipefs dentries creation logic has been changed:
1) Pipefs dentries creation by sb was moved to separated function, which will
be used for handling PipeFS mount notification.
2) Initial value of RPC client PipeFS dir dentry is set no NULL now.
RPC client pipefs dentries cleanup logic has been changed:
1) Cleanup is done now in separated rpc_remove_pipedir() function, which takes
care about pipefs superblock locking.
Also this patch removes slashes from cb_program.pipe_dir_name and from
NFS_PIPE_DIRNAME to make rpc_d_lookup_sb() work. This doesn't affect
vfs_path_lookup() results in nfs4blocklayout_init() since this slash is cutted
off anyway in link_path_walk().
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch is a final step towards to removing PipeFS inode references from
kernel code other than PipeFS itself. It makes all kernel SUNRPC PipeFS users
depends on pipe private data, which state depend on their specific operations,
etc.
This patch completes SUNRPC PipeFS preparations and allows to create pipe
private data and PipeFS dentries independently.
Next step will be making SUNPRC PipeFS dentries allocated by SUNRPC PipeFS
network namespace aware routines.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Currently gss auth holds RPC inode pointer which is now redundant since it
requires only pipes operations which takes private pipe data as an argument.
Thus this code can be cleaned and all references to RPC inode can be replaced
with privtae pipe data references.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
RPC pipe upcall doesn't requires only private pipe data. Thus RPC inode
references in this code can be removed.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch removes redundant RPC inode references from PipeFS. These places are
actually where pipes operations are performed.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Generally, pipe data is used only for pipes, and thus allocating space for it
on every RPC inode allocation is redundant. This patch splits private SUNRPC
PipeFS pipe data and inode, makes pipe data allocated only for pipe inodes.
This patch is also is a next step towards to to removing PipeFS inode
references from kernel code other than PipeFS itself.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Currenly, inode i_lock is used to provide concurrent access to SUNPRC PipeFS
pipes. It looks redundant, since now other use of inode is present in most of
these places and thus can be easely replaced, which will allow to remove most
of inode references from PipeFS code. This is a first step towards to removing
PipeFS inode references from kernel code other than PipeFS itself.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
During per-net pipes creation and destruction we have to make sure, that pipefs
sb exists for the whole creation/destruction cycle. This is done by using
special mutex which controls pipefs sb reference on network namespace context.
Helper consists of two parts: first of them (rpc_get_dentry_net) searches for
dentry with specified name and returns with mutex taken on success. When pipe
creation or destructions is completed, caller should release this mutex by
rpc_put_dentry_net call.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We have modules (like, pNFS blocklayout module) which creates pipes on
rpc_pipefs. Thus we need per-net operations for them. To make it possible we
require appropriate super block. So we have to put sb link on network namespace
context. Note, that it's not strongly required to create pipes in per-net
operations. IOW, if pipefs wasn't mounted yet, that no sb link reference will
present on network namespace and in this case we need just need to pass through
pipe creation. Pipe dentry will be created during pipefs mount notification.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
In all places, where pipefs dentries are created, only directory inode is
actually required to create new dentry. And all this directories has root
pipefs dentry as their parent. So we actually don't need this pipefs mount
point at all if some pipefs lookup method will be provided.
IOW, all we really need is just superblock and simple lookup method to find
root's child dentry with appropriate name. And this patch introduces this
method.
Note, that no locking implemented in rpc_d_lookup_sb(). So it can be used only
in case of assurance, that pipefs superblock still exist. IOW, we can use this
method only in pipefs mount-umount notification subscribers callbacks.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
They will be used to notify subscribers about pipefs superblock creation and
destruction.
Subcribers will have to create their dentries on passed superblock on mount
event and destroy otherwise.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We want to be sure that network namespace is still alive while we have pipefs
mounted.
This will be required later, when RPC pipefs will be mounting only from
user-space context.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This is the initial step of RPC pipefs virtualization. It changes nothing to
current pipefs behaviour except that mount of pipefs in other than init_net
network namespace context will provide only root tree. No other dentries will
be visible.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch-set was created in context of clone of git branch:
git://git.linux-nfs.org/projects/trondmy/nfs-2.6.git.
v2:
1) Rebased of current repo state (i.e. all commits were pulled before apply)
I feel it is ready for inclusion if no objections will appear.
SUNRPC pipefs non-exclusive pipe creation code looks obsolete. IOW, as I see
it, all pipes are creating with unique full path and only once.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
There is no limit on number of MD5 keys an application can attach to a
tcp socket.
This patch adds a per tcp socket limit based
on /proc/sys/net/core/optmem_max
With current default optmem_max values, this allows about 150 keys on
64bit arches, and 88 keys on 32bit arches.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be able to support proper RST messages for TCP MD5 flows, we
need to allow access to MD5 keys without locking listener socket.
This conversion is a nice cleanup, and shrinks size of timewait sockets
by 80 bytes.
IPv6 code reuses generic code found in IPv4 instead of duplicating it.
Control path uses GFP_KERNEL allocations instead of GFP_ATOMIC.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Shawn Lu <shawn.lu@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer use md5_add() method from struct tcp_sock_af_ops
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unted the assumption that the sta struct is still accessible before the
synchronize_rcu call we should move the num_sta_ps counter decrement
after synchronize_rcu to avoid incorrect decrements if num_sta_ps.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Handle MCS masks set by the user.
* Match rates provided by the rate control algorithm to the mask set,
also in HT mode, and switch back to legacy mode if necessary.
* add debugfs files to observate the rate selection
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow to set mcs masks through nl80211. We also allow to set MCS
rates but no legacy rates (and vice versa).
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the driver blocked this specific STA with the help of
ieee80211_sta_block_awake we won't clear WLAN_STA_PS_STA later but
still decrement num_sta_ps. Hence, the next data frame from this
STA will trigger ap_sta_ps_end again and also decrement num_sta_ps
again leading to an incorrect num_sta_ps counter.
This can result in problems with powersaving clients not waking up
from PS because the TIM calculation might be skipped due to the
incorrect num_sta_ps counter.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When WLAN_STA_PS_DRIVER is set by ieee80211_sta_block_awake the
num_sta_ps counter is not incremented. Hence, we shouldn't decrement
it in __sta_info_destroy if only WLAN_STA_PS_DRIVER is set. This
could result in an incorrect num_sta_ps counter leading to strange side
effects with associated powersaving clients.
Fix this by only decrementing num_sta_ps when WLAN_STA_PS_STA was set
before.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the future, when we start notifying drivers,
state transitions could potentially fail. To make
it easier to distinguish between programming bugs
and driver failures:
* rename sta_info_move_state() to
sta_info_pre_move_state() which can only be
called before the station is inserted (and
check this with a new station flag).
* rename sta_info_move_state_checked() to just
plain sta_info_move_state(), as it will be
the regular function that can fail for more
than just one reason (bad transition or an
error from the driver)
This makes the programming model easier -- one of
the functions can only be called before insertion
and can't fail, the other can fail.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit f1e3be1561.
Johannes Berg <johannes@sipsolutions.net> thinks that this patch is
incorrect. I'll defer to his judgment.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
text data bss dec hex filename
8455963 532732 1810804 10799499 a4c98b vmlinux.o.before
8448899 532732 1810804 10792435 a4adf3 vmlinux.o
This change also removes commented-out copy of __nlmsg_put
which was last touched in 2005 with "Enable once all users
have been converted" comment on top.
Changes in v2: rediffed against net-next.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Setting link attributes can modify the size of the attributes that
would be reported on a subsequent getlink netlink operation,
therefore min_ifinfo_dump_size needs to be adjusted. From Stefan
Gula.
2) Resegmentation of TSO frames while trimming can violate invariants
expected by callers, namely that the number of segments can only stay
the same or decrease, never increase. If MSS changes, however, we
can trim data but then end up with more segments. Fix this by only
segmenting to the MSS already recorded in the SKB. That's the
simplest fix for now and if we want to get more fancy in the future
that's a more involved change.
This probably explains some retransmit counter inaccuracies.
From Neal Cardwell.
3) Fix too-many-wakeups in POLL with AF_UNIX sockets, from Eric Dumazet.
4) Fix CAIF crashes wrt. namespace handling. From Eric Dumazet and
Eric W. Biederman.
5) TCP port selection fixes from Flavio Leitner.
6) More socket memory cgroup build fixes in certain randonfig
situations. From Glauber Costa.
7) Fix TCP memory sysctl regression reported by Ingo Molnar, also from
Glauber Costa.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
af_unix: fix EPOLLET regression for stream sockets
tcp: fix tcp_trim_head() to adjust segment count with skb MSS
net/tcp: Fix tcp memory limits initialization when !CONFIG_SYSCTL
net caif: Register properly as a pernet subsystem.
netns: Fail conspicously if someone uses net_generic at an inappropriate time.
net: explicitly add jump_label.h header to sock.h
net: RTNETLINK adjusting values of min_ifinfo_dump_size
ipv6: Fix ip_gre lockless xmits.
xen-netfront: correct MAX_TX_TARGET calculation.
netns: fix net_alloc_generic()
tcp: bind() optimize port allocation
tcp: bind() fix autoselection to share ports
l2tp: l2tp_ip - fix possible oops on packet receive
iwlwifi: fix PCI-E transport "inta" race
mac80211: set bss_conf.idle when vif is connected
mac80211: update oper_channel on ibss join
RFC5722 Section 4 was amended by Errata 3089
Our implementation did the right thing anyway...
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ability to return neighbour proxies list to caller if
it sent full ndmsg structure and has NTF_PROXY flag set.
Before this patch (and before iproute2 patches):
$ ip neigh add proxy 2001::1 dev eth0
$ ip -6 neigh show
$
After it and with applied iproute2 patches:
$ ip neigh add proxy 2001::1 dev eth0
$ ip -6 neigh show
2001::1 dev eth0 proxy
$
Compatibility with old versions of iproute2 is not broken,
kernel checks for incoming structure size and properly
works if old structure is came.
[v2]
* changed comments style.
* removed useless line with continue and curly bracket.
* changed incoming message size check from equal to more or
equal.
CC: davem@davemloft.net
CC: kuznet@ms2.inr.ac.ru
CC: netdev@vger.kernel.org
CC: xemul@parallels.com
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0884d7aa24 (AF_UNIX: Fix poll blocking problem when reading from
a stream socket) added a regression for epoll() in Edge Triggered mode
(EPOLLET)
Appropriate fix is to use skb_peek()/skb_unlink() instead of
skb_dequeue(), and only call skb_unlink() when skb is fully consumed.
This remove the need to requeue a partial skb into sk_receive_queue head
and the extra sk->sk_data_ready() calls that added the regression.
This is safe because once skb is given to sk_receive_queue, it is not
modified by a writer, and readers are serialized by u->readlock mutex.
This also reduce number of spinlock acquisition for small reads or
MSG_PEEK users so should improve overall performance.
Reported-by: Nick Mathewson <nickm@freehaven.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Alexey Moiseytsev <himeraster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes tcp_trim_head() to recalculate the number of
segments in the skb with the skb's existing MSS, so trimming the head
causes the skb segment count to be monotonically non-increasing - it
should stay the same or go down, but not increase.
Previously tcp_trim_head() used the current MSS of the connection. But
if there was a decrease in MSS between original transmission and ACK
(e.g. due to PMTUD), this could cause tcp_trim_head() to
counter-intuitively increase the segment count when trimming bytes off
the head of an skb. This violated assumptions in tcp_tso_acked() that
tcp_trim_head() only decreases the packet count, so that packets_acked
in tcp_tso_acked() could underflow, leading tcp_clean_rtx_queue() to
pass u32 pkts_acked values as large as 0xffffffff to
ca_ops->pkts_acked().
As an aside, if tcp_trim_head() had really wanted the skb to reflect
the current MSS, it should have called tcp_set_skb_tso_segs()
unconditionally, since a decrease in MSS would mean that a
single-packet skb should now be sliced into multiple segments.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl_tcp_mem() initialization was moved to sysctl_tcp_ipv4.c
in commit 3dc43e3e4d, since it
became a per-ns value.
That code, however, will never run when CONFIG_SYSCTL is
disabled, leading to bogus values on those fields - causing hung
TCP sockets.
This patch fixes it by keeping an initialization code in
tcp_init(). It will be overwritten by the first net namespace
init if CONFIG_SYSCTL is compiled in, and do the right thing if
it is compiled out.
It is also named properly as tcp_init_mem(), to properly signal
its non-sysctl side effect on TCP limits.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Glauber Costa <glommer@parallels.com>
Cc: David S. Miller <davem@davemloft.net>
Link: http://lkml.kernel.org/r/4F22D05A.8030604@parallels.com
[ renamed the function, tidied up the changelog a bit ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
caif is a subsystem and as such it needs to register with
register_pernet_subsys instead of register_pernet_device.
Among other problems using register_pernet_device was resulting in
net_generic being called before the caif_net structure was allocated.
Which has been causing net_generic to fail with either BUG_ON's or by
return NULL pointers.
A more ugly problem that could be caused is packets in flight why the
subsystem is shutting down.
To remove confusion also remove the cruft cause by inappropriately
trying to fix this bug.
With the aid of the previous patch I have tested this patch and
confirmed that using register_pernet_subsys makes the failure go away as
it should.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's only used to get at neigh->primary_key, which in this context is
always going to be the same as rt->rt6i_gateway.
Signed-off-by: David S. Miller <davem@davemloft.net>
In this specific situation we know we are dealing with a gatewayed route
and therefore rt6i_gateway is not going to be in6addr_any even in future
interpretations.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now all code paths grab a local reference to the neigh, so if neigh
is not NULL we unconditionally release it at the end. The old logic
would only release if we didn't have a non-NULL 'rt'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when we are on an IBSS network with no active station,
we would scan for other BSSID, even if fixed_bssid is on, due to
a bug in ibss.c, where fixed_channel would be checked instead of
fixed_bssid. This would trigger useless scans where scan results
would not be used anyway.
This patch also reverts commit 39d02a7d90,
which assumed that the ifibss->fixed_channel check was legitimate
to disable single-channel scans. IBSS single-channel scan should
now be fixed.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sta might be in psm against the ap (e.g. because
this was the before a hw restart), so we explicitly
send a null packet in order to make sure it'll
sync against the ap (and get out of psm).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a pointer so it should be NULL instead of zero. Sparse
complains about this stuff:
net/nfc/nci/core.c:447:37: warning: Using plain integer as NULL pointer
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A mesh node that joins the mesh network is by default a forwarding entity. This patch allows
the mesh node to set as non-forwarding entity. Whenever dot11MeshForwarding is set to 0, the
mesh node can prevent itself from forwarding the traffic which is not destined to him.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems that -Wshadow is no longer default in
sparse runs, but let's fix the warnings anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems that -Wshadow is no longer default in
sparse runs, but let's fix the warnings anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to the previous beacon filtering patch,
make CQM RSSI support depend on the flags that
the driver set for virtual interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to firmware limitations, we may not be able to
support beacon filtering on all virtual interfaces.
To allow this in mac80211, introduce per-interface
driver capability flags that the driver sets when
an interface is added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting link parameters on a netdevice changes the value
of if_nlmsg_size(), therefore it is necessary to recalculate
min_ifinfo_dump_size.
Signed-off-by: Stefan Gula <steweg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tunnel devices set NETIF_F_LLTX to bypass HARD_TX_LOCK. Sit and
ipip set this unconditionally in ops->setup, but gre enables it
conditionally after parameter passing in ops->newlink. This is
not called during tunnel setup as below, however, so GRE tunnels are
still taking the lock.
modprobe ip_gre
ip tunnel add test0 mode gre remote 10.5.1.1 dev lo
ip link set test0 up
ip addr add 10.6.0.1 dev test0
# cat /sys/class/net/test0/features
# $DIR/test_tunnel_xmit 10 10.5.2.1
ip route add 10.5.2.0/24 dev test0
ip tunnel del test0
The newlink callback is only called in rtnl_netlink, and only if
the device is new, as it calls register_netdevice internally. Gre
tunnels are created at 'ip tunnel add' with ioctl SIOCADDTUNNEL,
which calls ipgre_tunnel_locate, which calls register_netdev.
rtnl_newlink is called at 'ip link set', but skips ops->newlink
and the device is up with locking still enabled. The equivalent
ipip tunnel works fine, btw (just substitute 'method gre' for
'method ipip').
On kernels before /sys/class/net/*/features was removed [1],
the first commented out line returns 0x6000 with method gre,
which indicates that NETIF_F_LLTX (0x1000) is not set. With ipip,
it reports 0x7000. This test cannot be used on recent kernels where
the sysfs file is removed (and ETHTOOL_GFEATURES does not currently
work for tunnel devices, because they lack dev->ethtool_ops).
The second commented out line calls a simple transmission test [2]
that sends on 24 cores at maximum rate. Results of a single run:
ipip: 19,372,306
gre before patch: 4,839,753
gre after patch: 19,133,873
This patch replicates the condition check in ipgre_newlink to
ipgre_tunnel_locate. It works for me, both with oseq on and off.
This is the first time I looked at rtnetlink and iproute2 code,
though, so someone more knowledgeable should probably check the
patch. Thanks.
The tail of both functions is now identical, by the way. To avoid
code duplication, I'll be happy to rework this and merge the two.
[1] http://patchwork.ozlabs.org/patch/104610/
[2] http://kernel.googlecode.com/files/xmit_udp_parallel.c
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only semantic difference is that we now hold a reference to the
neighbour and thus have to release it.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the future the ipv4/ipv6 route gateway will take on two types
of values:
1) INADDR_ANY/IN6ADDR_ANY, for local network routes, and in this case
the neighbour must be obtained using the destination address in
ipv4/ipv6 header as the lookup key.
2) Everything else, the actual nexthop route address.
So if the gateway is not inaddr-any we use it, otherwise we must use
the packet's destination address.
Signed-off-by: David S. Miller <davem@davemloft.net>
It might be useful to get a counter of failed tcp_retransmit_skb()
calls.
Reported-by: Satoru Moriya <satoru.moriya@hds.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new net namespace is created, we should attach to it a "struct
net_generic" with enough slots (even empty), or we can hit the following
BUG_ON() :
[ 200.752016] kernel BUG at include/net/netns/generic.h:40!
...
[ 200.752016] [<ffffffff825c3cea>] ? get_cfcnfg+0x3a/0x180
[ 200.752016] [<ffffffff821cf0b0>] ? lockdep_rtnl_is_held+0x10/0x20
[ 200.752016] [<ffffffff825c41be>] caif_device_notify+0x2e/0x530
[ 200.752016] [<ffffffff810d61b7>] notifier_call_chain+0x67/0x110
[ 200.752016] [<ffffffff810d67c1>] raw_notifier_call_chain+0x11/0x20
[ 200.752016] [<ffffffff821bae82>] call_netdevice_notifiers+0x32/0x60
[ 200.752016] [<ffffffff821c2b26>] register_netdevice+0x196/0x300
[ 200.752016] [<ffffffff821c2ca9>] register_netdev+0x19/0x30
[ 200.752016] [<ffffffff81c1c67a>] loopback_net_init+0x4a/0xa0
[ 200.752016] [<ffffffff821b5e62>] ops_init+0x42/0x180
[ 200.752016] [<ffffffff821b600b>] setup_net+0x6b/0x100
[ 200.752016] [<ffffffff821b6466>] copy_net_ns+0x86/0x110
[ 200.752016] [<ffffffff810d5789>] create_new_namespaces+0xd9/0x190
net_alloc_generic() should take into account the maximum index into the
ptr array, as a subsystem might use net_generic() anytime.
This also reduces number of reallocations in net_assign_generic()
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sjur Brændeland <sjur.brandeland@stericsson.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port autoselection finds a port and then drop the lock,
then right after that, gets the hash bucket again and lock it.
Fix it to go direct.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code checks for conflicts when the application
requests a specific port. If there is no conflict, then
the request is granted.
On the other hand, the port autoselection done by the kernel
fails when all ports are bound even when there is a port
with no conflict available.
The fix changes port autoselection to check if there is a
conflict and use it if not.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet is received on an L2TP IP socket (L2TPv3 IP link
encapsulation), the l2tpip socket's backlog_rcv function calls
xfrm4_policy_check(). This is not necessary, since it was called
before the skb was added to the backlog. With CONFIG_NET_NS enabled,
xfrm4_policy_check() will oops if skb->dev is null, so this trivial
patch removes the call.
This bug has always been present, but only when CONFIG_NET_NS is
enabled does it cause problems. Most users are probably using UDP
encapsulation for L2TP, hence the problem has only recently
surfaced.
EIP: 0060:[<c12bb62b>] EFLAGS: 00210246 CPU: 0
EIP is at l2tp_ip_recvmsg+0xd4/0x2a7
EAX: 00000001 EBX: d77b5180 ECX: 00000000 EDX: 00200246
ESI: 00000000 EDI: d63cbd30 EBP: d63cbd18 ESP: d63cbcf4
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Call Trace:
[<c1218568>] sock_common_recvmsg+0x31/0x46
[<c1215c92>] __sock_recvmsg_nosec+0x45/0x4d
[<c12163a1>] __sock_recvmsg+0x31/0x3b
[<c1216828>] sock_recvmsg+0x96/0xab
[<c10b2693>] ? might_fault+0x47/0x81
[<c10b2693>] ? might_fault+0x47/0x81
[<c1167fd0>] ? _copy_from_user+0x31/0x115
[<c121e8c8>] ? copy_from_user+0x8/0xa
[<c121ebd6>] ? verify_iovec+0x3e/0x78
[<c1216604>] __sys_recvmsg+0x10a/0x1aa
[<c1216792>] ? sock_recvmsg+0x0/0xab
[<c105a99b>] ? __lock_acquire+0xbdf/0xbee
[<c12d5a99>] ? do_page_fault+0x193/0x375
[<c10d1200>] ? fcheck_files+0x9b/0xca
[<c10d1259>] ? fget_light+0x2a/0x9c
[<c1216bbb>] sys_recvmsg+0x2b/0x43
[<c1218145>] sys_socketcall+0x16d/0x1a5
[<c11679f0>] ? trace_hardirqs_on_thunk+0xc/0x10
[<c100305f>] sysenter_do_call+0x12/0x38
Code: c6 05 8c ea a8 c1 01 e8 0c d4 d9 ff 85 f6 74 07 3e ff 86 80 00 00 00 b9 17 b6 2b c1 ba 01 00 00 00 b8 78 ed 48 c1 e8 23 f6 d9 ff <ff> 76 0c 68 28 e3 30 c1 68 2d 44 41 c1 e8 89 57 01 00 83 c4 0c
Signed-off-by: James Chapman <jchapman@katalix.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An nsproxy argument here has always been awkard and now the nsproxy argument
is completely unnecessary so remove it, replacing it with the set we want
the registered tables to show up in.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Add a ctl_table_root pointer to ctl_table set so it is easy to
go from a ctl_table_set to a ctl_table_root.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
In sysctl_net register the two networking roots in the proper order.
In register_sysctl walk the sysctl sets in the reverse order of the
sysctl roots.
Remove parent from ctl_table_set and setup_sysctl_set as it is no
longer needed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
This adds a small helper retire_sysctl_set to remove the intimate knowledge about
the how a sysctl_set is implemented from net/sysct_net.c
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Simplify the code by treating the base sysctl table like any other
sysctl table and register it with register_sysctl_table.
To ensure this table is registered early enough to avoid problems
call sysctl_init from proc_sys_init.
Rename sysctl_net.c:sysctl_init() to net_sysctl_init() to avoid
name conflicts now that kernel/sysctl.c:sysctl_init() is no longer
static.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
We can remove the rt_gateway == 0 check but we shouldn't
remove the 'dst' initialization too.
Noticed by Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
We can remove the rt_gateway == 0 check but we shouldn't
remove the 'dst' initialization too.
Noticed by Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
It can never actually happen. rt_gateway is either the fully resolved
flow lookup key's destination address, or the non-zero FIB entry gateway
address.
Signed-off-by: David S. Miller <davem@davemloft.net>
rds_sock_info() triggers locking warnings because we try to perform a
local_bh_enable() (via sock_i_ino()) while hardware interrupts are
disabled (via taking rds_sock_lock).
There is no reason for rds_sock_lock to be a hardware IRQ disabling
lock, none of these access paths run in hardware interrupt context.
Therefore making it a BH disabling lock is safe and sufficient to
fix this bug.
Reported-by: Kumar Sanghvi <kumaras@chelsio.com>
Reported-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The file net/core/flow_dissector.c seems to be missing
including linux/export.h.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race on sk_receive_queue between llc_ui_recvmsg and
sock_queue_rcv_skb.
Our current solution is to protect skb_eat in llc_ui_recvmsg
with the queue spinlock.
Signed-off-by: Radu Iliescu <riliescu@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__ieee80211_recalc_idle() iterates through the vifs,
sets bss_conf.idle = true if they are disconnected,
and increases "count" if they are not (which later
gets evaluated in order to determine whether the
device is idle).
However, the loop doesn't set bss_conf.idle = false
(along with increasing "count"), causing the device
idle state and the vif idle state to get out of sync
in some cases.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 13c40c5 ("mac80211: Add HT operation modes for IBSS") broke
ibss operation by mistakenly removing the local->oper_channel
update (causing ibss to start on the wrong channel). fix it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the ability to select between multiple targets in NCI.
If only one target is found, it will be auto-activated.
If more than one target is found, then DISCOVER_NTF will be
generated for each target, and the host should select one by
calling DISCOVER_SELECT_CMD. Then, the target will be activated.
If the activation fails, GENERIC_ERROR_NTF is generated.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The NFC core layer should not set the target_idx.
Instead, the driver layer (e.g. NCI, PN533) should set the
target_idx, so that it will be able to identify the target
when its I/F (e.g. activate_target) is called.
This is required in order to support multiple targets.
Note that currently supported drivers (PN533 and NCI) don't
use the target_idx in their implementation.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make a clear separation between NCI states and flags.
This is required in order to support more NCI states (e.g.
for multiple targets support).
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of a node re-joining the cell the sta_info structure belonging to it is
first destroyed and then reinserted. In this way its internal state is reset.
The joining operation is recognised thank the Auth frame being received.
This operation is helpful in case of a node being rebooted that is joining the
ad-hoc cell again, before its purge timeout on other nodes expires.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In IBSS mode, whenever a new station is added a 2-way authentication challenge
is performed. Actually this event can be used to recognise a new station joining
the cell even if its sta_info entry is already in the list.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add NCI data exchange timer to catch timeouts,
and call the data exchange callback with an error.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems exceedingly unlikely that we'll ever
support swapping rate control algorithms at
runtime, so remove the unused refcounting code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yogesh's patch to destroy aggregation sessions when
stations are destroyed was needed, but unnecessarily
complex. Clean up this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export new attributes sensb_res for tech B and sensf_res
for tech F in the target info (returned as a response to
NFC_CMD_GET_TARGET).
The max size of the attributes nfcid1, sensb_res and sensf_res
is exported to user space though include/linux/nfc.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Actually the DA field has already been checked along the rx path (in
prepare_for_handlers()) and this check is therefore useless at this point.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The local maximum transmit power for a channel is defined as the maximum
regulatory transmission power minus the local power constraint specified
for the channel in the Power Constraint element. (7.3.2.15 IEEE80211 2007)
Signed-off-by: Hong Wu <hong.wu@dspg.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The local maximum transmit power is the maximum power a wireless device
allowed to transmit. If Power Constraint is presented, the local maximum
power equals to the maximum allowed power defined in regulatory domain
minus power constraint.
The maximum transmit power is maximum power a wireless device capable of
transmitting, and should be used in Power Capability element (7.3.2.16
IEEE802.11 2007).
The transmit power from a wireless device should not greater than the
local maximum transmit power.
The maximum transmit power was not calculated correctly in the current
Linux wireless/mac80211 when Power Constraint is presented.
Signed-off-by: Hong Wu <hong.wu@dspg.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of authentication frame exchange between two IBSS STAs, the
DA field must contain the destinatioin address (instead of the BSSID).
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a switch statement instead of a list of if
statements. Also include AP_VLAN in the list
and skip them since the AP interface will also
be looked at.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a target was active, complete the NCI deactivate request
only in deactivate_ntf. Otherwise, complete it at deactivate_rsp.
Deactivate_ntf represents the actual disconnection event (sent from
the NCI controller).
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we would have bailed out if 'ifibss->fixed_channel'
is valid i.e. we had used 'fixed-freq' parameter in iw ibss
join command. this is with the state 'IEEE80211_IBSS_MLME_JOINED'
so no need to check for it
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bail out if sta_apply_parameters() returns an error.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- generic_create_cred needs to copy the '.principal' field.
- generic_match needs to ignore the groups and match on the '.principal'
field.
This fixes an Oops that was introduced by commit 68c9715 (SUNRPC:
Clean up the RPCSEC_GSS service ticket requests)
Reported-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Tested-by: J. Bruce Fields <bfields@redhat.com>
Allow ETHTOOL_GSSET_INFO ethtool ioctl() for unprivileged users.
ETHTOOL_GSTRINGS is already allowed, but is unusable without this one.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes:
net/bluetooth/hci_core.c: In function ‘__check_enable_hs’:
net/bluetooth/hci_core.c:2587:1: warning: return from incompatible pointer type [enabled by default]
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a case in __sk_mem_schedule(), where an allocation
is beyond the maximum, but yet we are allowed to proceed.
It happens under the following condition:
sk->sk_wmem_queued + size >= sk->sk_sndbuf
The network code won't revert the allocation in this case,
meaning that at some point later it'll try to do it. Since
this is never communicated to the underlying res_counter
code, there is an inbalance in res_counter uncharge operation.
I see two ways of fixing this:
1) storing the information about those allocations somewhere
in memcg, and then deducting from that first, before
we start draining the res_counter,
2) providing a slightly different allocation function for
the res_counter, that matches the original behavior of
the network code more closely.
I decided to go for #2 here, believing it to be more elegant,
since #1 would require us to do basically that, but in a more
obscure way.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
CC: Tejun Heo <tj@kernel.org>
CC: Li Zefan <lizf@cn.fujitsu.com>
CC: Laurent Chavey <chavey@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
md5 key is added in socket through remote address.
remote address should be used in finding md5 key when
sending out reset packet.
Signed-off-by: shawnlu <shawn.lu@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every call to num_args() immediately checks the return value for
less than zero, as it will return -EFAULT for a failed get_user()
call. So it makes no sense for the function to be declared as an
unsigned long.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correctly implement a loss detection heuristic: New sequences (above
high_seq) sent during the fast recovery are deemed lost when higher
sequences are SACKed.
Current code does not catch these losses, because tcp_mark_head_lost()
does not check packets beyond high_seq. The fix is straight-forward by
checking packets until the highest sacked packet. In addition, all the
FLAG_DATA_LOST logic are in-effective and redundant and can be removed.
Update the loss heuristic comments. The algorithm above is documented
as heuristic B, but it is redundant too because heuristic A already
covers B.
Note that this change only marks some forward-retransmitted packets LOST.
It does NOT forbid TCP performing further CWR on new losses. A potential
follow-up patch under preparation is to perform another CWR on "new"
losses such as
1) sequence above high_seq is lost (by resetting high_seq to snd_nxt)
2) retransmission is lost.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With netem reordering, a gap of N is supposed to reorder every Nth packet with
given reorder probability. However, the code currently skips N packets and
reorders every (N+1)th packet.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes CUBIC so that cwnd reductions made during RTOs can be
undone (just as they already can be undone when using the default/Reno
behavior).
When undoing cwnd reductions, BIC-derived congestion control modules
were restoring the cwnd from last_max_cwnd. There were two problems
with using last_max_cwnd to restore a cwnd during undo:
(a) last_max_cwnd was set to 0 on state transitions into TCP_CA_Loss
(by calling the module's reset() functions), so cwnd reductions from
RTOs could not be undone.
(b) when fast_covergence is enabled (which it is by default)
last_max_cwnd does not actually hold the value of snd_cwnd before the
loss; instead, it holds a scaled-down version of snd_cwnd.
This patch makes the following changes:
(1) upon undo, revert snd_cwnd to ca->loss_cwnd, which is already, as
the existing comment notes, the "congestion window at last loss"
(2) stop forgetting ca->loss_cwnd on TCP_CA_Loss events
(3) use ca->last_max_cwnd to check if we're in slow start
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Sangtae Ha <sangtae.ha@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes BIC so that cwnd reductions made during RTOs can be
undone (just as they already can be undone when using the default/Reno
behavior).
When undoing cwnd reductions, BIC-derived congestion control modules
were restoring the cwnd from last_max_cwnd. There were two problems
with using last_max_cwnd to restore a cwnd during undo:
(a) last_max_cwnd was set to 0 on state transitions into TCP_CA_Loss
(by calling the module's reset() functions), so cwnd reductions from
RTOs could not be undone.
(b) when fast_covergence is enabled (which it is by default)
last_max_cwnd does not actually hold the value of snd_cwnd before the
loss; instead, it holds a scaled-down version of snd_cwnd.
This patch makes the following changes:
(1) upon undo, revert snd_cwnd to ca->loss_cwnd, which is already, as
the existing comment notes, the "congestion window at last loss"
(2) stop forgetting ca->loss_cwnd on TCP_CA_Loss events
(3) use ca->last_max_cwnd to check if we're in slow start
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel contains some special internal keyrings, for instance the DNS
resolver keyring :
2a93faf1 I----- 1 perm 1f030000 0 0 keyring .dns_resolver: empty
It would occasionally be useful to allow the contents of such keyrings to be
flushed by root (cache invalidation).
Allow a flag to be set on a keyring to mark that someone possessing the
sysadmin capability can clear the keyring, even without normal write access to
the keyring.
Set this flag on the special keyrings created by the DNS resolver, the NFS
identity mapper and the CIFS identity mapper.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Steve Dickson <steved@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
There is a race condition in addrconf_sysctl_forward() and
addrconf_sysctl_disable().
These functions change idev->cnf.forwarding (resp. idev->cnf.disable_ipv6)
and then try to grab the rtnl lock before performing any actions.
If that fails they restore the original value and restart the syscall.
This creates race conditions if ipv6 code tries to access
these parameters, or if multiple instances try to do the same operation.
As an example of the former, if __ipv6_ifa_notify() finds a 0 in
idev->cnf.forwarding when invoked by addrconf_ifdown() it may not free
anycast addresses, ultimately resulting in the net_device not being freed.
This patch reads the user parameters into a temporary location and only
writes the actual parameters when the rtnl lock is acquired.
Tested in 2.6.38.8.
Signed-off-by: Francesco Ruggeri <fruggeri@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deauth is requested while an auth or assoc
work item is in progress, we currently delete it
without regard for any state it might need to
clean up. Fix it by cleaning up for those items.
In the case Pontus found, the problem manifested
itself as such:
authenticate with 00:23:69:aa:dd:7b (try 1)
authenticated
failed to insert Dummy STA entry for the AP (error -17)
deauthenticating from 00:23:69:aa:dd:7b by local choice (reason=2)
It could also happen differently if the driver
uses the tx_sync callback.
We can't just call the ->done() method of the work
items because that will lock up due to the locking
in cfg80211. This fix isn't very clean, but that
seems acceptable since I have patches pending to
remove this code completely.
Cc: stable@vger.kernel.org
Reported-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Tested-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use local->tx_headroom instad of local->hw.extra_tx_headroom.
local->tx_headroom is the max of hw.extra_tx_headroom required by the
driver and the headroom required by mac80211 for status reporting. On
drivers where hw.extra_tx_headroom is smaller than what mac80211
requires (e.g. ath5k), we would not reserve sufficient buffer space to
report tx status.
Also, don't reserve local->tx_headroom + local->hw.extra_tx_headroom.
Reported-by: Simon Morgenthaler <s.morgenthaler@students.unibe.ch>
Reported-by: Kai Scharwies <kai@scharwies.de>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since stations moved into a virtual interface
subdirectory, this link has been broken. Fix it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
tg3: Fix single-vector MSI-X code
openvswitch: Fix multipart datapath dumps.
ipv6: fix per device IP snmp counters
inetpeer: initialize ->redirect_genid in inet_getpeer()
net: fix NULL-deref in WARN() in skb_gso_segment()
net: WARN if skb_checksum_help() is called on skb requiring segmentation
caif: Remove bad WARN_ON in caif_dev
caif: Fix typo in Vendor/Product-ID for CAIF modems
bnx2x: Disable AN KR work-around for BCM57810
bnx2x: Remove AutoGrEEEn for BCM84833
bnx2x: Remove 100Mb force speed for BCM84833
bnx2x: Fix PFC setting on BCM57840
bnx2x: Fix Super-Isolate mode for BCM84833
net: fix some sparse errors
net: kill duplicate included header
net: sh-eth: Fix build error by the value which is not defined
net: Use device model to get driver name in skb_gso_segment()
bridge: BH already disabled in br_fdb_cleanup()
net: move sock_update_memcg outside of CONFIG_INET
mwl8k: Fixing Sparse ENDIAN CHECK warning
...
The logic to split up the list of datapaths into multiple Netlink messages
was simply wrong, causing the list to be terminated after the first part.
Only about the first 50 datapaths would be dumped. This fixes the
problem.
Reported-by: Paul Ingram <paul@nicira.com>
Signed-off-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 4ce3c183fc (snmp: 64bit ipstats_mib for all arches), I forgot
to change the /proc/net/dev_snmp6/xxx output for IP counters.
percpu array is 64bit per counter but the folding still used the 'long'
variant, and output garbage on 32bit arches.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmemcheck complains that ->redirect_genid doesn't get initialized.
Presumably it should be set to zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_checksum_help() has never done anything useful with skbs that
require segmentation. Setting skb->ip_summed = CHECKSUM_NONE makes
them invalid and provokes a later WARNing in skb_gso_segment().
Passing such an skb to skb_checksum_help() indicates a bug, so we
should warn about it immediately. Move the warning from
skb_gso_segment() into a shared function, and add gso_type and
gso_size to it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove WARN_ON and bad handling of SKB without destructor callback
in caif_flow_cb. SKB without destructor cannot be handled as an
error case.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typo for the Vendor/Product Id for ST-Ericsson CAIF modems.
Discovery is based on fixed USB vendor 0x04cc (ST-Ericsson),
product-id 0x230f (NCM).
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
make C=2 CF="-D__CHECK_ENDIAN__" M=net
And fix flowi4_init_output() prototype for sport
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jozsef Kadlecsik
Marcel Holtmann
Linus Torvalds
Johan Hedberg
H. Peter Anvin
H. J. Lu
John W. Linville
Eric Dumazet
David S. Miller
Andre Guedes
Tom Tucker
Danny Kukawka
Weston Andros Adamson
Andrei Emeltchenko
Joe Perches
Andy Adamson
Stanislav Kinsbursky
Sven Eckelmann
Antonio Quartulli
Marek Lindner
Martin Hundebøll
Felix Fietkau
Johannes Berg
Ulisses Furquim
Octavian Purdila
Octavian Purdila
Andrzej Kaczmarek
Peter Hurley
Trond Myklebust
Axel Lin
Neal Cardwell
Dimitri Sivanich
David Herrmann
Szymon Janc
Vinicius Costa Gomes
Hemant Gupta
Andre Guedes
Fabio Estevam
Jiri Benc
Thomas Graf
Li Wei
Neil Horman
Masanari Iida
Mohammed Shafi Shajakhan
Florian Westphal
James Morris
Ursula Braun
Erich E. Hoover
Luis R. Rodriguez
Dan Carpenter
Anisse Astier
Shriram Rajagopalan
Allan Stephens
Eliad Peller
Steve Dickson
Jesper Juhl
Shawn Lu
sjur.brandeland@stericsson.com
Simon Horman
Sage Weil
Dmitry Tarnyagin
Jason Wang
Li Zefan
Ben Hutchings
Arun Sharma
Helmut Schaa
Simon Wunderlich
Denys Vlasenko
Tony Zelenoff
Glauber Costa
Eric W. Biederman
Nicolas Cavallari
Chun-Yeow Yeoh
Stefan Gula
Willem de Bruijn
Flavio Leitner
James Chapman
Jesper Dangaard Brouer
Radu Iliescu
Ilan Elias
Hong Wu
Michał Mirosław
Paul Gortmaker
Yuchung Cheng
Vijay Subramanian
David Howells
Francesco Ruggeri
Javier Cardona
Ben Pfaff