I guess I forgot to add it, nah, now it just works:
18:04:33.274066 IP6 ::1.1476 > ::1.5001: request (service=0)
18:04:33.334482 IP6 ::1.5001 > ::1.1476: reset (code=bad_service_code)
Ditched IP_DCCP_UNLOAD_HACK, as now we would have to do it for both
IPv6 and IPv4, so I'll come up with another way for freeing the
control sockets in upcoming changesets.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no reason for struct dccp_v4_prot being global.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_triestats has been buggy and caused oopses some platforms as
openwrt. The patch below should cure those problems.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some kernel configs /proc functions seems to be accessed before the
trie is initialized. The patch below checks for this.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves some TCP-specific MTU probing state out of
inet_connection_sock back to tcp_sock.
Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch below replaces a divide by 2 with a shift -- sk_sndbuf is an
integer, so gcc emits an idiv, which takes 10x longer than a shift by 1.
This improves af_unix bandwidth by ~6-10K/s. Also, tidy up the comment
to fit in 80 columns while we're at it.
Signed-off-by: Benjamin LaHaise <benjamin.c.lahaise@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Uninline kfree_skb, which saves some 15k of object code on my notebook.
o Allow kfree_skb to be called with a NULL argument.
Subsequent patches can remove conditional from drivers and further
reduce source and object size.
Signed-off-by: Jrn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to Leslie Harlley Watter <leslie@watter.org> for reporting the
problem an testing this patch.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a race in pktgen which can lead to a double
free of a pktgen_dev's skb. If a worker thread is in
the midst of doing fill_packet(), and the controlling
thread gets a "stop" message, the already freed skb
can be freed once again in pktgen_stop_device(). This
patch gives all responsibility for cleaning up a
pktgen_dev's skb to the associated worker thread.
Signed-off-by: Arthur Kepner <akepner@sgi.com>
Acked-by: Robert Olsson <Robert.Olsson@data.slu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch in place we can break down the complexity by better
compartmentalizing the code that is common to ipv6 and ipv4.
Now we have these modules:
Module Size Used by
dccp_diag 1344 0
inet_diag 9448 1 dccp_diag
dccp_ccid3 15856 0
dccp_tfrc_lib 12320 1 dccp_ccid3
dccp_ccid2 5764 0
dccp_ipv4 16996 2
dccp 48208 4 dccp_diag,dccp_ccid3,dccp_ccid2,dccp_ipv4
dccp_ipv6 still requires dccp_ipv4 due to dccp_ipv6_mapped, that is
the next target to work on the "hey, ipv4 is legacy, I only want ipv6
dude!" direction.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And introduce dccp_mib_exit grouping previously open coded sequence.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dccp_make_response is shared by ipv4/6 and the ipv6 code was
recalculating the checksum, not good, so move the dccp_v4_checksum
call to dccp_v4_send_response.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As this is used by both ipv4 and ipv6 and is not ipv4 specific.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing one more ipv6 uses ipv4 stuff case in dccp land.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Import the NID_cast5_cbc from the userland context. Not used.
Signed-off-by: Andy Adamson <andros@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Use a spinlock to ensure unique sequence numbers when creating krb5 gss tokens.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Remove unnecessary kmalloc of temporary space to hold the md5 result; it's
small enough to just put on the stack.
This code may be called to process rpc's necessary to perform writes, so
there's a potential deadlock whenever we kmalloc() here. After this a
couple kmalloc()'s still remain, to be removed soon.
This also fixes a rare double-free on error noticed by coverity.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Renaming it to dccp_send_reset and moving it from the ipv4 specific
code to the core dccp code.
This fixes some bugs in IPV6 where timers would send v4 resets, etc.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[root@qemu ~]# for a in /proc/sys/net/dccp/default/* ; do echo $a ; cat $a ; done
/proc/sys/net/dccp/default/ack_ratio
2
/proc/sys/net/dccp/default/rx_ccid
3
/proc/sys/net/dccp/default/send_ackvec
1
/proc/sys/net/dccp/default/send_ndp
1
/proc/sys/net/dccp/default/seq_window
100
/proc/sys/net/dccp/default/tx_ccid
3
[root@qemu ~]#
So if wanting to test ccid3 as the tx CCID one can just do:
[root@qemu ~]# echo 3 > /proc/sys/net/dccp/default/tx_ccid
[root@qemu ~]# echo 2 > /proc/sys/net/dccp/default/rx_ccid
[root@qemu ~]# cat /proc/sys/net/dccp/default/[tr]x_ccid
2
3
[root@qemu ~]#
Of course we also need the setsockopt for each app to tell its preferences, but
for testing or defining something other than CCID2 as the default for apps that
don't explicitely set their preference the sysctl interface is handy.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that dccp_feat_clean doesn't get confused with uninitialized
list_heads.
Noticed when testing with no ccid kernel modules.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make CCID2 and CCID3 default to what was selected for DCCP and use the
standard short description for the CCIDs (TCP-Like & TCP-Friendly).
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also fixes the layout of dccp_hdr short sequence numbers, problem
was not fatal now as we only support long (48 bits) sequence numbers.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge netfilter code simulates the NF_IP_PRE_ROUTING hook and skips
the real hook by registering with high priority and returning NF_STOP if
skb->nf_bridge is present and the BRNF_NF_BRIDGE_PREROUTING flag is not
set. The flag is only set during the simulated hook.
Because skb->nf_bridge is only freed when the packet is destroyed, the
packet will not only skip the first invocation of NF_IP_PRE_ROUTING, but
in the case of tunnel devices on top of the bridge also all further ones.
Forwarded packets from a bridge encapsulated by a tunnel device and sent
as locally outgoing packet will also still have the incorrect bridge
information from the input path attached.
We already have nf_reset calls on all RX/TX paths of tunnel devices,
so simply reset the nf_bridge field there too. As an added bonus,
the bridge information for locally delivered packets is now also freed
when the packet is queued to a socket.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the CCID upon successful feature negotiation.
Commiter note: patch mostly rewritten to use the new ccid API.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. No need for ->ccid_init nor ->ccid_exit, this is what module_{init,exit}
does and anynways neither ccid2 nor ccid3 were using it.
2. Rename struct ccid to struct ccid_operations and introduce struct ccid
with a pointer to ccid_operations and rigth after it the rx or tx
private state.
3. Remove the pointer to the state of the half connections from struct
dccp_sock, now its derived thru ccid_priv() from the ccid pointer.
Now we also can implement the setsockopt for changing the CCID easily as
no ccid init routines can affect struct dccp_sock in any way that prevents
other CCIDs from working if a CCID switch operation is asked by apps.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert sch_red to a classful qdisc. All qdiscs that maintain accurate
backlog counters are eligible as child qdiscs. When a queue limit larger
than zero is given, a bfifo qdisc is used for backwards compatibility.
Current versions of tc enforce a limit larger than zero, other users
can avoid creating the default qdisc by using zero.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is similar to the SA expire insertion patch - only it inserts
expires for SP.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows a user to insert SA expires. This is useful to
do on an HA backup for the case of byte counts but may not be very
useful for the case of time based expiry.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a feature similar to the one described in RFC 2367:
"
... the application needing an SA sends a PF_KEY
SADB_ACQUIRE message down to the Key Engine, which then either
returns an error or sends a similar SADB_ACQUIRE message up to one or
more key management applications capable of creating such SAs.
...
...
The third is where an application-layer consumer of security
associations (e.g. an OSPFv2 or RIPv2 daemon) needs a security
association.
Send an SADB_ACQUIRE message from a user process to the kernel.
<base, address(SD), (address(P),) (identity(SD),) (sensitivity,)
proposal>
The kernel returns an SADB_ACQUIRE message to registered
sockets.
<base, address(SD), (address(P),) (identity(SD),) (sensitivity,)
proposal>
The user-level consumer waits for an SADB_UPDATE or SADB_ADD
message for its particular type, and then can use that
association by using SADB_GET messages.
"
An app such as OSPF could then use ipsec KM to get keys
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fast path sequence updates that will generate ipsec async
events
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the core functionality needed for sync events
for ipsec. Derived work of Krisztian KOVACS <hidden@balabit.hu>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep backlog counter in SFQ qdisc to make it usable as child qdisc
with RED.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TBF was converted to a classful qdisc, the semantic of the limit
parameter was broken. On initilization an inner bfifo qdisc is created
for backwards compatibility, when changing parameters however the new
limit is ignored and the current child qdisc remains in place.
Always replace the child qdisc by the default bfifo when limit is above
zero, otherwise don't touch the inner qdisc. Current tc version enforce
a limit above zero, other users can avoid creating the inner qdisc by
using zero.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A qdisc should set tcm_info to the child qdisc handle in its class
dump function.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The drop operation is optional and qdiscs must check if childs support it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep a bitmask of multicast groups with subscribed listeners to let
netlink users check for listeners before generating multicast
messages.
Queries don't perform any locking, which may result in false
positives, it is guaranteed however that any new subscriptions are
visible before bind() or setsockopt() return.
Signed-off-by: Patrick McHardy <kaber@trash.net>
ACKed-by: Jamal Hadi Salim<hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid unneccessary event message generation by checking for netlink
listeners before building a message.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace netfilter's ip6_masked_addrcmp by a more efficient version
in include/net/ipv6.h to make it usable without module dependencies.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to make decisions based on the revision (and address family
with a follow-up patch) at runtime.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new functions for common match/target checks (private data
size, valid hooks, valid tables and valid protocols) to get more consistent
error reporting and to avoid each module duplicating them.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent (kernel 2.6.15.1) fix for PPTP NAT helper introduced a
bug - which only appears if DEBUGP is enabled though.
The calculation of the CID offset into a PPTP request struct is
not correct, so that at least not the correct CID is displayed
if DEBUGP is enabled.
This patch corrects CID offset calculation and introduces a #define
for that.
Signed-off-by: Holger Eitzenberger <heitzenberger@astaro.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a hybrid use of standard timers and sk_timers. This caused
the reference count of the sock to be incorrect when resetting the RTO
timer. The sock reference count should now be correct, enabling its
destruction, and allowing the DCCP module to be unloaded.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch moves all helper related data fields of 'struct nf_conn'
into a separate structure 'struct nf_conn_help'. This new structure
is only present in conntrack entries for which we actually have a
helper loaded.
Also, this patch cleans up the nf_conntrack 'features' mechanism to
resemble what the original idea was: Just glue the feature-specific
data structures at the end of 'struct nf_conn', and explicitly
re-calculate the pointer to it when needed rather than keeping
pointers around.
Saves 20 bytes per conntrack on my x86_64 box. A non-helped conntrack
is 276 bytes. We still need to save another 20 bytes in order to fit
into to target of 256bytes.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implementation of packetization layer path mtu discovery for TCP, based on
the internet-draft currently found at
<http://www.ietf.org/internet-drafts/draft-ietf-pmtud-method-05.txt>.
Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
vfree does it's own NULL checking, so checking a pointer before
handing it to vfree is pointless.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original work by Andrea Bittau, Arnaldo Melo cleaned up and fixed several
issues on the merge process.
For now CCID2 was turned the default for all SOCK_DCCP connections, but this
will be remedied soon with the merge of the feature negotiation code.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing if the ccid being instantiated has these methods in
ccid_init().
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on a patch by Andrea Bittau.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplifying the code a bit as we're always using DCCP_MAX_ACKVEC_LEN.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using a sequence number for every logged netfilter event, we can
determine from userspace whether logging information was lots somewhere
downstream.
The user has a choice of either having per-instance local sequence
counters, or using a global sequence counter, or both.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Try to allocate the struct file and an unused file
descriptor before we try to pull a newly accepted
socket out of the protocol layer.
Based upon a patch by Prassana Meda.
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch adds support to the VLAN driver to translate IF_OPER_DORMANT of the
underlying device to netif_dormant_on(). Beside clean state forwarding, this
allows running independant userspace supplicants on both the real device and
the stacked VLAN. It depends on my RFC2863 patch.
Signed-off-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch adds a dormant flag to network devices, RFC2863 operstate derived
from these flags and possibility for userspace interaction. It allows drivers
to signal that a device is unusable for user traffic without disabling
queueing (and therefore the possibility for protocol establishment traffic to
flow) and a userspace supplicant (WPA, 802.1X) to mark a device unusable
without changes to the driver.
It is the result of our long discussion. However I must admit that it
represents what Jamal and I agreed on with compromises towards Krzysztof, but
Thomas and Krzysztof still disagree with some parts. Anyway I think it should
be applied.
Signed-off-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to get redirects from nexthop of "more-specific"
routes.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check RTF_ADDRCONF|RTF_DEFAULT in rt6_get_dflt_router().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
And prepare for more advanced router selection.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This controls whether we accept Prefix Information in RAs.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This controls whether we accept default router information
in RAs.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 3041 describes an algorithm to generate random interface
identifier. In RFC 3041bis, it is allowed to use different
algorithm than one described in RFC 3041.
So, let's use our standard pseudo random algorithm to simplify
our implementation.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since addrconf_add_dev() has already called addrconf_add_mroute()
to added route for multicast prefix, there's no point to call it
again in addrconf_ip6_tnl_config().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently this will not happen if we exit before rpc_new_task() was called.
Also fix up rpc_run_task() to do the same (for consistency).
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Hi,
When a network interface goes into promiscuous mode, its an important security
issue. The attached patch is intended to capture that action and send an
event to the audit system.
The patch carves out a new block of numbers for kernel detected anomalies.
These are events that may indicate suspicious activity. Other examples of
potential kernel anomalies would be: exceeding disk quota, rlimit violations,
changes to syscall entry table.
Signed-off-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We need to ensure that all writes to the XDR buffers are done before
req->rq_received is visible to other processors.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Introduced by NFS metrics patch.
Test plan:
Compile kernel with CONFIG_NFS enabled on a 64-bit platform.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
RPC_DEBUG_DATA no longer needed in net/sunrpc/xprt.c.
Test plan:
Compile kernel with CONFIG_NFS enabled.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean-up: replace rpc_call() helper with direct call to rpc_call_sync.
This makes NFSv2 and NFSv3 synchronous calls more computationally
efficient, and reduces stack consumption in functions that used to
invoke rpc_call more than once.
Test plan:
Compile kernel with CONFIG_NFS enabled. Connectathon on NFS version 2,
version 3, and version 4 mount points.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add fields to the rpc_procinfo struct that allow the display of a
human-readable name for each procedure in the rpc_iostats output.
Also fix it so that the NFSv4 stats are broken up correctly by
sub-procedure number. NFSv4 uses only two real RPC procedures:
NULL, and COMPOUND.
Test plan:
Mount with NFSv2, NFSv3, and NFSv4, and do "cat /proc/self/mountstats".
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add a simple mechanism for collecting stats in the RPC client. Stats are
tabulated during xprt_release. Note that per_cpu shenanigans are not
required here because the RPC client already serializes on the transport
write lock.
Test plan:
Compile kernel with CONFIG_NFS enabled. Basic performance regression
testing with high-speed networking and high performance server.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Account for various things that occur while an RPC task is executed.
Separate timers for RPC round trip and RPC execution time show how
long RPC requests wait in queue before being sent. Eventually these
will be accumulated at xprt_release time in one place where they can
be viewed from userland.
Test plan:
Compile kernel with CONFIG_NFS enabled.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Monitor generic transport events. Add a transport switch callout to
format transport counters for export to user-land.
Test plan:
Compile kernel with CONFIG_NFS enabled.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
RPC wait queue length will eventually be exported to userland via the RPC
iostats interface.
Test plan:
Compile kernel with CONFIG_NFS enabled.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch adds server ip address to be printed out when "server
requires stronger authentication" error occured.
Signed-off-by: Levent Serinol <lserinol@gmail.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If not, we cannot guarantee that idmap->idmap_dentry, gss_auth->dentry and
clnt->cl_dentry are valid dentries.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch adds a request_module call to rpcauth_create which will try
to auto-load the kernel module for the requested authentication flavor.
For kernels with modular sunrpc, this reduces the admin overhead for
the user.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If the AX.25 dialect chosen by the sysadmin is set to DAMA master / 3
(or DAMA slave / 2, if CONFIG_AX25_DAMA_SLAVE=n) ax25_kick() will fall
through the switch statement without calling ax25_send_iframe() or any
other function that would eventually free skbn thus leaking the packet.
Fix by restricting the sysctl inferface to allow only actually supported
AX.25 dialects.
The system administration mistake needed for this to happen is rather
unlikely, so this is an uncritical hole.
Coverity #651.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem in the ieee80211 probe response and beacon
reception code that would use the packet statistics for a network even
if they were received on a channel other than that which the network
exists on.
This causes a problem in overlapping channels where, for example, a
strong AP on channel 2 could have its beacons received on channels 1 and
3, but at much lower signal levels. If scanning was done sequentially,
this means the beacon received on channel 3 would update the AP's signal
level as being much lower than it really is, which subsequently could
cause that AP to be passed over and an alternate AP selected.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix QoS is not active even the network and the card is QOS enabled.
The problem is we pass the wrong ieee80211_network address to
ipw_handle_beacon/ipw_handle_probe_response, thus the
ieee80211_network->qos_data.active will not be set, causing the driver
not sending QoS frames at all.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rpc_wake_up() and rpc_wake_up_status(), it is possible for the call to
__rpc_wake_up_task() to fail if another thread happens to be calling
rpc_wake_up_task() on the same rpc_task.
Problem noticed by Bruno Faccini.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Coverity checker spotted this possible NULL pointer dereference in
rpc_new_client().
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we link a socket into the hash table, we need to make sure that we
set the num/port fields so that it shows us with a non-zero port value
in proc/netlink and on the wire. This code and comment is copied over
from the IPv4 stack as is.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The check is wrong and lets NULL-ptrs slip through since !IS_ERR(NULL)
is true.
Coverity #190
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ufo_append_data fails err is uninitialized, but returned back.
Strangely gcc doesn't notice it.
Coverity #901 and #902
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb given to netlink_cmsg_recv_pktinfo is already freed, move it up
a few lines.
Coverity #948
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
tmp_hdr is not freed when ipv6_clear_mutable_options fails.
Coverity #650
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb is allocated by the function, so it needs to be freed instead
of trimmed on overrun.
Coverity #614
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix NULL-ptr dereference when a config message for a non-existant
queue containing only an NFQA_CFG_PARAMS attribute is received.
Coverity #433
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
That's >= a full sized TSO frame, so we should always
return 0 in that case.
Based upon a report and initial patch from Lachlan
Andrew, final patch suggested by Herbert Xu.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Gregor Maier <gregor@net.in.tum.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scope element in the ipv6_saddr_score struct used in
ipv6_dev_get_saddr() is an unsigned integer, but __ipv6_addr_src_scope()
returns a signed integer (and can return -1).
Signed-off-by: Brian Haley <brian.haley@hp.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have benchmarked this on an x86_64 NUMA system and see no significant
performance difference on kernbench. Tested on both x86_64 and powerpc.
The way we do file struct accounting is not very suitable for batched
freeing. For scalability reasons, file accounting was
constructor/destructor based. This meant that nr_files was decremented
only when the object was removed from the slab cache. This is susceptible
to slab fragmentation. With RCU based file structure, consequent batched
freeing and a test program like Serge's, we just speed this up and end up
with a very fragmented slab -
llm22:~ # cat /proc/sys/fs/file-nr
587730 0 758844
At the same time, I see only a 2000+ objects in filp cache. The following
patch I fixes this problem.
This patch changes the file counting by removing the filp_count_lock.
Instead we use a separate percpu counter, nr_files, for now and all
accesses to it are through get_nr_files() api. In the sysctl handler for
nr_files, we populate files_stat.nr_files before returning to user.
Counting files as an when they are created and destroyed (as opposed to
inside slab) allows us to correctly count open files with RCU.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The size of the skb carrying the netlink message is not
equivalent to the length of the actual netlink message
due to padding. ip_queue matches the length of the payload
against the original packet size to determine if packet
mangling is desired, due to the above wrong assumption
arbitary packets may not be mangled depening on their
original size.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare circumstances 0 is returned by dccp_li_hist_calc_i_mean which
leads to a divide by zero in ccid3_hc_rx_packet_recv. Explicitly check
for zero return now. Update copyright notice at same time.
Found by Arnaldo.
Signed-off-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The earlier round of kobject/sysfs changes to bridge caused
it not to generate a uevent on removal. Don't think any application
cares (not sure about Xen) but since it generates add uevent
it should generate remove as well.
Signed-off-by: Stephen Hemminger <shemmigner@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize the STP timers for a port when it is created,
rather than when it is enabled. This will prevent future race conditions
where timer gets started before port is enabled.
Signed-off-by: Stephen Hemminger <shemmigner@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge would crash because of uninitailized timer if STP is used and
device was inserted into a bridge before bridge was up. This got
introduced when the delayed port checking was added. Fix is to not
enable STP on port unless bridge is up.
Bugzilla: http://bugzilla.kernel.org/show_bug.cgi?id=6140
Dup: http://bugzilla.kernel.org/show_bug.cgi?id=6156
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally submitted by Kenzo Iwami; his original description is:
The current bonding driver receives duplicate packets when broadcast/
multicast packets are sent by other devices or packets are flooded by the
switch. In this patch, new flags are added in priv_flags of net_device
structure to let the bonding driver discard duplicate packets in
dev.c:skb_bond().
Modified by Jay Vosburgh to change a define name, update some
comments, rearrange the new skb_bond() for clarity, clear all bonding
priv_flags on slave release, and update the driver version.
Signed-off-by: Kenzo Iwami <k-iwami@cj.jp.nec.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I have come to consider BUG_ON generally harmful. The idea of an assert is
to prevent a program to execute past a point where its state is known
erroneous, thus preventing it from dealing more damage to the data
(or hiding the traces of malfunction). The problem is, in kernel this harm
has to be balanced against the harm of forced reboot.
The last straw was our softmac tree, where "iwlist eth1 scan" causes
a lockup. It is absolutely frivolus and provides no advantages a normal
assert has to provide. In fact, doing this impedes debugging.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In 295f7324ff I moved defer_accept from
tcp_sock to request_queue and mistakingly reset it at reqsl_queue_alloc, causing
calls to setsockopt(TCP_DEFER_ACCEPT ) to be lost after bind, the fix is to
remove the zeroing of rskq_defer_accept from reqsl_queue_alloc.
Thanks to Alexandra N. Kossovsky <Alexandra.Kossovsky@oktetlabs.ru> for
reporting and testing the suggested fix.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nfnetlink_log infrastructure changes broke compatiblity of the LOG
targets. They currently use whatever log backend was registered first,
which means that if ipt_ULOG was loaded first, no messages will be printed
to the ring buffer anymore.
Restore compatiblity by using the old log functions by default and only use
the nf_log backend if the user explicitly said so.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comparison wants to find out if the last list iteration reached the
end of the list. It needs to compare the iterator with the list head to
do this, not the element it is looking for.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only point of registering a queue handler is to provide an outfn,
so there is no need to check for it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets should be rerouted when they come back from userspace, not before.
Also move the queue_rerouters to RCU to avoid taking the queue_handler_lock
for each reinjected packet.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every rerouter needs to provide a save and a reroute function, we don't
need to check for them. But we do need to check if a rerouter is registered
at all for the current family, with bridging for example packets of
unregistered families can hit nf_queue.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the registered data structure instead of copying it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only reason post_input exists at all is that it gives us the
potential to adjust the checksums incrementally in future which
we ought to do.
However, after thinking about it for a bit we can adjust the
checksums without using this post_input stuff at all. The crucial
point is that only the inner-most NAT-T SA needs to be considered
when adjusting checksums. What's more, the checksum adjustment
comes down to a single u32 due to the linearity of IP checksums.
We just happen to have a spare u32 lying around in our skb structure :)
When ip_summed is set to CHECKSUM_NONE on input, the value of skb->csum
is currently unused. All we have to do is to make that the checksum
adjustment and voila, there goes all the post_input and decap structures!
I've left in the decap data structures for now since it's intricately
woven into the sec_path stuff. We can kill them later too.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to keep sg on the stack which is why the extra block was useful.
We've long since stopped doing that so let's kill the block and save
some indentation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on patch by Hoerdt Mickael <hoerdt@clarinet.u-strasbg.fr>.
Signed-off-by: YOSHIFUJI Hideaki <yosufuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The included patch fixes ip6_tunnel to release the cached dst entry
when the tunnel parameters (such as tunnel endpoints) are changed so
they are used immediatly for the next encapsulated packets.
Signed-off-by: Hugo Santos <hsantos@av.it.pt>
Acked-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should use the TOS because it's one of the routing keys. It also
means that we update the correct routing cache entry when PMTU occurs.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When you turn off ARP on a netdevice then the first packet always goes
out with a dstMAC of all zeroes. This is because the first packet is
used to resolve ARP entries. Even though the ARP entry may be resolved
(I tried by setting a static ARP entry for a host i was pinging from),
it gets overwritten by virtue of having the netdevice disabling ARP.
Subsequent packets go out fine with correct dstMAC address (which may
be why people have ignored reporting this issue).
To cut the story short:
the culprit code is in net/ethernet/eth.c::eth_header()
----
/*
* Anyway, the loopback-device should never use this
function...
*/
if (dev->flags & (IFF_LOOPBACK|IFF_NOARP))
{
memset(eth->h_dest, 0, dev->addr_len);
return ETH_HLEN;
}
if(daddr)
{
memcpy(eth->h_dest,daddr,dev->addr_len);
return ETH_HLEN;
}
----
Note how the h_dest is being reset when device has IFF_NOARP.
As a note:
All devices including loopback pass a daddr. loopback in fact passes
a 0 all the time ;->
This means i can delete the check totaly or i can remove the IFF_NOARP
Alexey says:
--------------------
I think, it was me who did this crap. It was so long ago I do not remember
why it was made.
I remember some troubles with dummy device. It tried to resolve
addresses, apparently, without success and generated errors instead of
blackholing. I think the problem was eventually solved at neighbour
level.
After some thinking I suspect the deletion of this chunk could change
behaviour of some parts which do not use neighbour cache f.e. packet
socket.
I think safer approach would be to move this chunk after if (daddr).
And the possibility to remove this completely could be analyzed later.
--------------------
Patch updated with Alexey's safer suggestions.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Acked-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
We often just do an atomic_dec(&x->refcnt) on an xfrm_state object
because we know there is more than 1 reference remaining and thus
we can elide the heavier xfrm_state_put() call.
Do this behind an inline function called __xfrm_state_put() so that is
more obvious and also to allow us to more cleanly add refcount
debugging later.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When garbage collecting route cache entries of multipath routes
in rt_garbage_collect(), entries were deleted from the hash bucket
'i' while holding a spin lock on bucket 'k' resulting in a system
hang. Delete entries, if any, from bucket 'k' instead.
Signed-off-by: Suresh Bhogavilli <sbhogavilli@verisign.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge-netfilter code attaches a fake dst_entry with dst->ops == NULL
to purely bridged packets. When these packets are SNATed and a policy
lookup is done, xfrm_lookup crashes because it tries to dereference
dst->ops.
Change xfrm_lookup not to dereference dst->ops before checking for the
DST_NOXFRM flag and set this flag in the fake dst_entry.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of netfilter-related members are initalized / copied twice in
skb_clone(). Remove one.
Pointed out by Olivier MATZ <olivier.matz@6wind.com>.
And this patch also fixes order of copying / clearing members.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When redirecting an outgoing packet to loopback, it keeps the original
conntrack reference and information from the outgoing path, which
falsely triggers the check for DNAT on input and the dst_entry is
released to trigger rerouting. ip_route_input refuses to route the
packet because it has a local source address and it is dropped.
Look at the packet itself to dermine if it was NATed. Also fix a
missing inversion that causes unneccesary xfrm lookups.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ICMP errors are only SNATed when their source matches the source of the
connection they are related to, otherwise the source address is not
changed. This creates problems with ICMP frag. required messages
originating from a router behind the NAT, if private IPs are used the
packet has a good change of getting dropped on the path to its destination.
Always NAT ICMP errors similar to the original connection.
Based on report by Al Viro.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It replaces returning WPA/RSN IEs as custom events with returning them
as IWEVGENIE events. I have tested that it returns proper information
with both Xsupplicant, and the latest development version of the Linux
wireless tools.
Signed-off-by: Chris Hessing <Chris.Hessing@utah.edu>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If skb->ip_summed is CHECKSUM_HW here, skb->csum includes checksum
of actual IPv6 header and extension headers. Then such excess
checksum must be subtruct when nf_conntrack calculates TCP/UDP checksum
with pseudo IPv6 header. Spotted by Ben Skeggs.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Locally generated ICMPv6 errors should be associated with the conntrack
of the original packet. Since the conntrack entry may not be in the hash
tables (for the first packet), it must be manually attached.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP RSTs generated by the REJECT target should be associated with the
conntrack of the original TCP packet. Since the conntrack entry is
usually not is the hash tables, it must be manually attached.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move registration of __nf_ct_attach to nf_conntrack_core to make it usable
for IPv6 connection tracking as well.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
NF_CONNTRACK_MARK is bool and depends on NF_CONNTRACK which is
tristate. If a variable depends on NF_CONNTRACK_MARK and doesn't take
care about NF_CONNTRACK, it can be y even if NF_CONNTRACK isn't y.
NF_CT_ACCT have same issue, too.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet matching an IPsec policy is SNATed so it doesn't match any
policy anymore it looses its xfrm bundle, which makes xfrm4_output_finish
crash because of a NULL pointer dereference.
This patch directs these packets to the original output path instead. Since
the packets have already passed the POST_ROUTING hook, but need to start at
the beginning of the original output path which includes another
POST_ROUTING invocation, a flag is added to the IPCB to indicate that the
packet was rerouted and doesn't need to pass the POST_ROUTING hook again.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like somebody forgot to use the _bh spin_lock variant. We ran into a
deadlock where br->hello_timer expired while br_stp_disable_br() walked
br->port_list.
Signed-off-by: Adrian Drzewiecki <z@drze.net>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To find out if a packet needs to be handled by IPsec after SNAT, packets
are currently rerouted in POST_ROUTING and a new xfrm lookup is done. This
breaks SNAT of non-unicast packets to non-local addresses because the
packet is routed as incoming packet and no neighbour entry is bound to the
dst_entry. In general, it seems to be a bad idea to replace the dst_entry
after the packet was already sent to the output routine because its state
might not match what's expected.
This patch changes the xfrm lookup in POST_ROUTING to re-use the original
dst_entry without routing the packet again. This means no policy routing
can be used for transport mode transforms (which keep the original route)
when packets are SNATed to match the policy, but it looks like the best
we can do for now.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert the following changeset:
bc8dfcb939
Recursive SKB frag lists are really possible and disallowing
them breaks things.
Noticed by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem discovered and initial patch by Olaf Kirch:
there's a problem with IPsec that has been bugging some of our users
for the last couple of kernel revs. Every now and then, IPsec will
freeze the machine completely. This is with openswan user land,
and with kernels up to and including 2.6.16-rc2.
I managed to debug this a little, and what happens is that we end
up looping in xfrm_lookup, and never get out. With a bit of debug
printks added, I can this happening:
ip_route_output_flow calls xfrm_lookup
xfrm_find_bundle returns NULL (apparently we're in the
middle of negotiating a new SA or something)
We therefore call xfrm_tmpl_resolve. This returns EAGAIN
We go to sleep, waiting for a policy update.
Then we loop back to the top
Apparently, the dst_orig that was passed into xfrm_lookup
has been dropped from the routing table (obsolete=2)
This leads to the endless loop, because we now create
a new bundle, check the new bundle and find it's stale
(stale_bundle -> xfrm_bundle_ok -> dst_check() return 0)
People have been testing with the patch below, which seems to fix the
problem partially. They still see connection hangs however (things
only clear up when they start a new ping or new ssh). So the patch
is obvsiouly not sufficient, and something else seems to go wrong.
I'm grateful for any hints you may have...
I suggest that we simply bail out always. If the dst decides to die
on us later on, the packet will be dropped anyway. So there is no
great urgency to retry here. Once we have the proper resolution
queueing, we can then do the retry again.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Olaf Kirch <okir@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
- panic() doesn't return.
- Don't forget to unlock on genl_register_family() error path
- genl_rcv_msg() is called via pointer so there's no point in declaring it
`inline'.
Notes:
genl_ctrl_event() ignores the genlmsg_multicast() return value.
lots of things ignore the genl_ctrl_event() return value.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horms patch was the best of the three fixes. Dave, already applied
Harald's version, so this patch converts that to the better one.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>