Only legacy PXA DMA implementation was using these rx_dma and tx_dma DMA
addresses so they are not needed after commit 6356437e65
("spi: spi-pxa2xx: remove legacy PXA DMA bits").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After removal of legacy PXA DMA code by the commit 6356437e65
("spi: spi-pxa2xx: remove legacy PXA DMA bits") the
CONFIG_SPI_PXA2XX_DMA follows the CONFIG_SPI_PXA2XX and cannot be disabled
alone. Therefore remove this config symbol and dead definitions from the
spi-pxa2xx.h.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not used since commit 8d94cc50aa ("[PATCH] spi: stabilize PIO mode
transfers on PXA2xx systems").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This was leftover from the legacy pxa2xx DMA implementation and not needed
anymore so remove it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Carry input clock of the controller in max_speed_hz of struct spi_master
instead of in own driver data. They mean the same thing and more over now
the max_speed_hz is not even set here.
As an added bonus this allows SPI core to validate that transfer speed is
not beyond the maximum input clock. This is not a problem in spi-pxa2xx as
the driver doesn't use transfer speed parameter directly but via input
clock divider calculation which will top at divide by one. However it's
better to validate speed before passing it here.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There hasn't been need to carry chip->cr0 after SPI core started to
validate speed_hz and bits_per_word transfer parameters. That effectively
caused that pump_transfers() always recalculated it and practically
chip->cr0 is used locally in setup() for debug prints only.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to carry spi->max_speed_hz and spi->bits_per_word from
setup() in "struct chip_data" since pump_transfers() will anyway take the
transfer parameters from "struct spi_transfer". This is since SPI core
validates both bits_per_word and speed_hz transfer parameters and defaults
to spi->bits_per_word and spi->max_speed_hz in case these per transfer
parameters are not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove null_dma_buf variable and extra allocation for it. It is not needed
since commit 6356437e65 ("spi: spi-pxa2xx: remove legacy PXA DMA bits").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These became unused by the commit 6356437e65
("spi: spi-pxa2xx: remove legacy PXA DMA bits").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Generic DMA support was already implemented by commit cd7bed0034
("spi/pxa2xx: break out the private DMA API usage into a separate file")
which moved all the legacy PXA DMA implementation code into its own
file.
With generic DMA available for PXA, we can now just trash this file.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mark Brown <broonie@linaro.org>
[respin after pxa dmaengine support upstream]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently SSP registers are accessed by having an own read and write macros
for each register. For instance read_SSSR(iobase) and write_SSSR(iobase).
In my opinion this hurts readability and requires new macros to be defined
for each new added register. Let's define and use instead common
pxa2xx_spi_read() and pxa2xx_spi_write() accessors.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are two SPI controllers exported by PCI subsystem for Intel Quark X1000.
The SPI memory mapped I/O registers supported by Quark are different from
the current implementation, and Quark only supports the registers of 'SSCR0',
'SSCR1', 'SSSR', 'SSDR', and 'DDS_RATE'. This patch is to enable the SPI for
Intel Quark X1000.
This piece of work is derived from Dan O'Donovan's initial work for Intel Quark
X1000 SPI enabling.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel LPSS SPI is pretty much the same as the PXA27xx SPI except that it
has few additional features over the original:
o FIFO depth is 256 entries
o RX FIFO has one watermark
o TX FIFO has two watermarks, low and high
o chip select can be controlled by writing to a register
The new FIFO registers follow immediately the PXA27xx registers but then there
are some additional LPSS private registers at offset 1k or 2k from the base
address. For these private registers we add new accessors that take advantage
of drv_data->lpss_base once it is resolved.
We add a new type LPSS_SSP that can be used to distinguish the LPSS devices
from others.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To be able to use DMA with this driver on non-PXA platforms we implement
support for the generic DMA engine API. This lets user to use different DMA
engines with little or no modification to the driver.
Request lines and channel numbers can be passed to the driver from the
platform specific data.
The DMA engine implementation will be selected by default even on PXA
platform. User can select the legacy DMA API by enabling Kconfig option
CONFIG_SPI_PXA2XX_PXADMA.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PXA SPI driver uses PXA platform specific private DMA implementation
which does not work on non-PXA platforms. In order to use this driver on
other platforms we break out the private DMA implementation into a separate
file that gets compiled only when CONFIG_SPI_PXA2XX_PXADMA is set. The DMA
functions are stubbed out if there is no DMA implementation selected (i.e
we are building on non-PXA platform).
While we are there we can kill the dummy DMA bits in pxa2xx_spi.h as they
are not needed anymore for CE4100.
Once this is done we can add the generic DMA engine support to the driver
that allows usage of any DMA controller that implements DMA engine API.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jarkko Nikula
Mark Brown
Mika Westerberg
Daniel Mack
Weike Chen