Just like the use of the flag ESDHC_FLAG_MULTIBLK_NO_INT, let's add
another flag ESDHC_FLAG_ENGCM07207 to enable the workaround for errata
ENGcm07207 and set the flag for i.MX25 and i.MX35 ESDHC.
While at it, let's use BIT() macro for ESDHC_FLAG_MULTIBLK_NO_INT as
well.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to spec, the pre_div for imx6q should be 1, or the biggest
clock rate we can get is a half of host clock rate. This may cause
we can not get the proper clock rate as we want. e.g. if the desired
clock is 200Mhz, however, the host clock is 200Mhz too, then it causes
the actual clock we get is 100Mhz due to pre_div is 2.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Without proper pinctrl state, the card may not be able to work
on high speed stablely. e.g. SDR104.
This patch add pinctrl state switch code according to different
uhs mode include 100mhz sate, 200mhz sate and normal state
(50Mhz and below).
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Freescale i.MX6Q/DL uSDHC clock tuning progress is a little different from
the standard tuning process defined in host controller spec v3.0.
Thus we use platform_execute_tuning instead of standard sdhci tuning.
The main difference are:
1) not only generate Buffer Read Ready interrupt when tuning is performing.
It generates all other DATA interrupts like the normal data command.
2) SDHCI_CTRL_EXEC_TUNING is not automatically cleared by HW,
instead it's controlled by SW.
3) SDHCI_CTRL_TUNED_CLK is not automatically set by HW,
it's controlled by SW.
4) the clock delay for every tuning is set by SW.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The signal voltage switch flow requires to shutdown and output
clock in a specific sequence according to standard host controller
v3.0 spec. In that timing, the card must really receive clock or not.
However, for i.MX6Q, the uSDHC will not output clock even the clock
is enabled until there is command or data in transfer on the bus,
which will then cause singal voltage switch always to fail.
For i.MX6Q, we clear ESDHC_VENDOR_SPEC_FRC_SDCLK_ON bit to let
controller to gate off clock automatically and set that bit
to force clock output if clock is on.
This is required by SD3.0 support.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We need a lot of imx6 specific things into common esdhc_set_clock
for support SD3.0 and eMMC DDR mode which is not needed for power pc
platforms, so esdhc_set_clock seems not so common anymore.
Instead of keeping add platform specfics things into this common API,
we choose to move that code into platform driver itself to handle.
This can also exclude the dependency between imx and power pc on this
headfile and is easy for maintain in the future.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a debounce parameter to the mmc_gpio_request_cd() function that
enables GPIO debouncing when set to a non-zero value. This can be used
by MMC host drivers to enable debouncing on the card detect signal.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In order to make it possible to reduce the SD bus frequency,
parse the optional "max-frequency" attribute as documented in
devicetree/bindings/mmc/mmc.txt
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The SDCLK is divided down from the host controller clock. Host
controller clock may be different from the maximum SDCLK, so
get it from the platform, instead of just using the max SDCLK.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a param to allow users of sdhci_pltfm to allocate private space
in calls to sdhci_pltfm_init+sdhci_pltfm_register. This is implemented
in the same way as sdhci does for its users.
None of the users have been migrated yet and are passing in zero to
retain their private allocation.
- todo: migrate clients to using allocation this way
- todo: remove priv variable once migration is complete
Also removed unused variable in sdhci_pltfm_init fn
Signed-off-by: Christian Daudt <csd@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The eSDHC controller on the i.MX53 needs an additional, non spec
compliant CMD12 after a multiblock read with a predefined number of
blocks. Otherwise the internal state machine won't go back to the
idle state.
This commit effectively reverts 5b6b0ad6 (mmc: sdhci-esdhc-imx:
fix for mmc cards on i.MX5), which fixed part of the problem by
making multiblock reads work, however this fix was not sufficient
when multi- and singleblock reads got intermixed.
This implements the recommended workaround (Freescale i.MX Reference
Manual, section 29.6.8 "Multi-block Read") by manually sending a
CMD12 with the RSPTYP bits cleared.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently SDIO interrupts do not work on i.MX53 and maybe others.
This was observed with a Marvell 8787 based SDIO wifi adapter
using the mwifiex driver and firmware from the Marvell git
repository.
The symptom was a timeout after firmware download.
Observing the SDIO_DAT1 line showed that an interrupt was requested
(level 0) but no interrupt was generated in software, the line
stayed low until a timeout ocurred and the card was reset.
There is a Freescale errata
ENGcm11186 "eSDHC misses SDIO interrupt when CINT is disabled"
The workaround suggested by this errata is already implemented and
involves clearing and then setting the D3CD bit in the host control
register [see esdhc_writel_le()]
However, when esdhc_writeb_le() is later used to write to
SDHCI_HOST_CONTROL it always resets the D3CD bit.
To fix this simply add the D3CD bit to the set of bits
not modified by esdhc_writeb_le().
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sdhci_pltfm_data struct is never modified within the sdhci_pltfm
module. So make the pdata parameter to sdhci_pltfm_init and
sdhci_pltfm_register const. This allows drivers to declare their
sdhci_pltfm_data struct as const.
This patch also makes the sdhci_pltfm_data declarations const where
possible.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Quite a few drivers have a implementation of the get_timeout_clock
callback which simply returns the result of clk_get_rate on the device's
clock. This patch adds a common implementation of this to the sdhci-pltfm
module and replaces all custom implementations with the common one.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The i.MX esdhc has a nonstandard bit layout for the SDHCI_HOST_CONTROL
register. To support 8bit bus width on i.MX populate the platform_bus_width
callback. This is tested on an i.MX25, but should according to the datasheets
work on the other i.MX using this hardware aswell. The i.MX6, while having
a SDHCI_SPEC_300 controller, still uses the same nonstandard register layout.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDHCI core will try to use Auto CMD23 for mmc card. Currently, we will
see the following message with mmc card on usdhc due to the lacking of
Auto CMD23 support in the driver.
$ mmc0: new high speed MMC card at address 0001
mmcblk1: mmc0:0001 MMC02G 1.87 GiB
mmcblk1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
mmcblk1: retrying using single block read
mmcblk1:
Enable Auto CMD23 support for usdhc so that mmc card can work in
multiple block mode.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
It's another violation to SDHC spec that software reset on usdhc
does not reset MIX_CTRL register. Have to do it manually, otherwise
the preserving of the register bits (e.g. AC23EN) may cause mmc card
fail to be initialized.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The combining of SDHCI_TRANSFER_MODE and SDHCI_COMMAND writes is only
required for esdhc, but not necessarily for usdhc. Different from
esdhc where the bits for transfer mode and command are all in the same
register CMD_XFR_TYP, usdhc has a newly introduced register MIX_CTRL
to hold transfer mode bits. So it makes more sense to separate transfer
mode from command write for usdhc.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Rename esdhc local definitions with ESDHC_ rather than SDHCI_ prefix,
so that we can distinguish them from SDHCI core definitions from name.
A couple of bit fields are also changed use shift for consistency and
better readability.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDHCI_CTRL_D3CD is not a standard SDHCI_HOST_CONTROL, so there is no
need to check it in SDHCI_HOST_CONTROL write at all. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When commit 95a2482 (mmc: sdhci-esdhc-imx: add basic imx6q usdhc
support) works around host version issue on imx6q, it gets the
register address fixup "reg ^= 2" lost for imx25/35/51/53 esdhc.
Thus, the controller version on these SoCs is wrongly identified
as v1 while it's actually v2.
Add the address fixup back and take a different approach to correct
imx6q host version, so that the host version read gets back to work
for all SoCs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
With commit 9444e07 (mmc: remove unncessary mmc_gpio_free_cd() call from
slot-gpio users) in place, the ESDHC_CD_GPIO handling in IO accessories
becomes unnecessary. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This is
going to be a pain for the merge with different subsystem trees, I know,
but all of the patches included here have been ACKed by their various
subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them all,
it's up to you. The merges should all be trivial, and Stephen has been
doing them all in linux-next for a few weeks now quite easily.
Other than the __dev* marking removals, there's nothing major here, some
firmware loading updates and other minor things in the driver core.
All of these have (much to Stephen's annoyance), been in linux-next for
a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHkPkACgkQMUfUDdst+ykaWgCfW7AM30cv0nzoVO08ax6KjlG1
KVYAn3z/KYazvp4B6LMvrW9y0G34Wmad
=yvVr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This
is going to be a pain for the merge with different subsystem trees, I
know, but all of the patches included here have been ACKed by their
various subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them
all, it's up to you. The merges should all be trivial, and Stephen
has been doing them all in linux-next for a few weeks now quite
easily.
Other than the __dev* marking removals, there's nothing major here,
some firmware loading updates and other minor things in the driver
core.
All of these have (much to Stephen's annoyance), been in linux-next
for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.
* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
modpost.c: Stop checking __dev* section mismatches
init.h: Remove __dev* sections from the kernel
acpi: remove use of __devinit
PCI: Remove __dev* markings
PCI: Always build setup-bus when PCI is enabled
PCI: Move pci_uevent into pci-driver.c
PCI: Remove CONFIG_HOTPLUG ifdefs
unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
sh/PCI: Remove CONFIG_HOTPLUG ifdefs
powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
mips/PCI: Remove CONFIG_HOTPLUG ifdefs
microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
dma: remove use of __devinit
dma: remove use of __devexit_p
firewire: remove use of __devinitdata
firewire: remove use of __devinit
leds: remove use of __devexit
leds: remove use of __devinit
leds: remove use of __devexit_p
mmc: remove use of __devexit
...
Use devm_kzalloc, devm_gpio_request_one and devm_request_irq to make
cleanup path simpler.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the imx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Patch to not set reserved bits in i.MX25 PROCTL register. DMA stops
working if those bits get set.
Signed-off-by: Wilson Callan <wilson.callan@savantsystems.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of the
samsung iommu code from a platform specific in-kernel interface to the
generic iommu subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hgkg
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc driver specific updates from Olof Johansson:
"These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of
the samsung iommu code from a platform specific in-kernel interface to
the generic iommu subsystem."
Fix up trivial conflicts in arch/arm/mach-exynos/Kconfig
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mmc: dt: Consolidate DT bindings
iommu/exynos: Add iommu driver for EXYNOS Platforms
ARM: davinci: optimize the DMA ISR
ARM: davinci: implement DEBUG_LL port choice
ARM: tegra: Add SMMU enabler in AHB
ARM: tegra: Add Tegra AHB driver
Input: pxa27x_keypad add choice to set direct_key_mask
Input: pxa27x_keypad direct key may be low active
Input: pxa27x_keypad bug fix for direct_key_mask
Input: pxa27x_keypad keep clock on as wakeup source
ARM: dt: tegra: pinmux changes for USB ULPI
ARM: tegra: add USB ULPI PHY reset GPIO to device tree
ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
ARM: tegra: change pll_p_out4's rate to 24MHz
ARM: tegra: fix pclk rate
ARM: tegra: reparent sclk to pll_c_out1
ARM: tegra: Add pllc clock init table
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
...
This patch unifies the current DT MMC bindings documentation and code,
adds generic MMC DT bindings documentation, and updates .dts files for
consistency.
[cjb: typo fixes, addition of max-frequency property]
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/net/ethernet/freescale/fec.c
drivers/spi/spi-imx.c
drivers/tty/serial/imx.c
This resolves dependencies between the pinctrl and clock changes
in imx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This was broken by me in 37865fe915
("mmc: sdhci-esdhc-imx: fix timeout on i.MX's sdhci") where more
extensive tests would have shown that read or write of data to the
card were failing (even if the partition table was correctly read).
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Conflicts:
arch/arm/mach-lpc32xx/clock.c
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c
The conflicts with pxa are non-obvious, we have multiple branches
adding and removing the same clock settings. According to
Haojian Zhuang, removing the sa1100 rtc dummy clock is the correct
fix here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On i.MX53 we have to write a special SDHCI_CMD_ABORTCMD to the
SDHCI_TRANSFER_MODE register during a MMC_STOP_TRANSMISSION
command. This works for SD cards. However, with MMC cards
the MMC_SET_BLOCK_COUNT command is used instead, but this
needs the same handling. Fix MMC cards by testing for the
MMC_SET_BLOCK_COUNT command aswell. Tested on a custom i.MX53
board with a Transcend MMC+ card and eMMC.
The kernel started used MMC_SET_BLOCK_COUNT in 3.0, so this
is a regression for these boards introduced in 3.0; it should
go to 3.0/3.1/3.2-stable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch converts the drivers in drivers/mmc/host/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Drop the "state" argument from sdhci_suspend_host. Its only user is the
PCI glue; this allows to move all SDHCI glues to use dev_pm_ops instead.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The following error is seen in some case when mounting rootfs from
SD/MMC cards.
Waiting for root device /dev/mmcblk0p1...
mmc1: host does not support reading read-only switch. assuming write-enable.
mmc1: new high speed SDHC card at address b368
mmcblk0: mmc1:b368 SDC 3.74 GiB
mmcblk0: p1
mmc1: Timeout waiting for hardware interrupt.
mmcblk0: error -110 transferring data, sector 3678224, nr 40, cmd response 0x900, card status 0xc00
end_request: I/O error, dev mmcblk0, sector 3678225
Buffer I/O error on device mmcblk0p1, logical block 458754
lost page write due to I/O error on mmcblk0p1
This patch fixes the problem by lowering the usdhc clock and correcting
watermark configuration.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds the basic support for imx6q usdhc, which is a
derivative of esdhc controller.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Eanble the ADMA2 mode for freescale esdhc imx driver, tested on MX25
3DS board, MX51 BBG board and MX53 LOCO board.
This patch is only used to enable the ADMA2 for MX51/53 platforms.
MX25/35 can't support the ADMA2 mode, set BROKEN_ADMA quirk on
MX25/35 platforms.
The ADMA mode supported or not can be distinguished by bit 20 of
the Capability Register (offset 0x40) in the FSL eSDHC module.
Signed-off-by: Richard Zhu <richard.zhu@linaro.org>
Tested-and-acked-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Shawn Guo
Dong Aisheng
Laurent Pinchart
Lucas Stach
Christian Daudt
Martin Fuzzey
Lars-Peter Clausen
Sascha Hauer
Fabio Estevam
Linus Torvalds
Bill Pemberton
Arnd Bergmann
Masanari Iida
Wilson Callan
Dong Aisheng
Eric Bénard
Richard Zhao
Axel Lin
Manuel Lauss
Richard Zhu