qfprom has different address spaces for read and write. Reads are
always done from corrected address space, where as writes are done
on raw address space.
Writing to corrected address space is invalid and ignored, so it
does not make sense to have this support in the driver which only
supports corrected address space regions at the moment.
Fixes: 4ab11996b4 ("nvmem: qfprom: Add Qualcomm QFPROM support.")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200522113341.7728-1-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes coccicheck warning:
drivers/nvmem/jz4780-efuse.c:214:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Samuel Zou <zou_wei@huawei.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200511145042.31223-4-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2a127da461 ("nvmem: add support for the write-protect pin")
added support for handling write-protect pins to the nvmem core, and
Commit 1c89074bf8 ("eeprom: at24: remove the write-protect pin support")
retrofitted the at24 driver to use this support.
These changes broke write() on the nvmem sysfs attribute for eeproms
which utilize a write-protect pin, as the write callback invokes the
nvmem device's reg_write callback directly which no longer handles
changing the state of the write-protect pin.
Change the read and write callbacks for the sysfs attribute to invoke
nvmme_reg_read/nvmem_reg_write helpers which handle this, rather than
calling reg_read/reg_write directly.
Fixes: 2a127da461 ("nvmem: add support for the write-protect pin")
Signed-off-by: Michael Auchter <michael.auchter@ni.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200511145042.31223-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several logic improvements to save many code lines:
- no need to use goto;
- no need to assign return value;
- combine different conditions of return value into one line.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200511145042.31223-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
file permission are derived based on various configs for
default nvmem sysfs file, reuse it to create the eeprom
compat file too.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200417121306.23121-1-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we are using is_bin_visible callback, we do not need
nvmem_sysfs_get_groups() anymore so move all the relevant data-structures
and code to core.c
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200325131951.31887-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By using is_bin_visible callback to set permissions will remove a
large list of attribute groups. These group permissions can be
dynamically derived in the callback.
Also add checks for read/write callbacks and set permissions accordingly.
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200325131951.31887-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we are planning to move to use sysfs is_bin_visible callback,
having root_only as part of nvmem_device will help decide correct
permissions.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200325122116.15096-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_add_action_or_reset() for cleanup to call clk_unprepare(),
which can simplify the error handling in .probe, and .remove callback
can be dropped.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200323150007.7487-5-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've saved the double data flag in the device data, so we should
use it when programming a block.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200323150007.7487-4-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have some cases that will programme the eFuse block partially multiple
times, so we should allow the block to be programmed again if it was
programmed partially. But we should lock the block if the whole block
was programmed. Thus add a condition to validate if we need lock the
block or not.
Moreover we only enable the auto-check function when locking the block.
Signed-off-by: Freeman Liu <freeman.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200323150007.7487-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the Spreadtrum eFuse specification, we should write 0 to
the block to trigger the lock operation.
Fixes: 096030e7f4 ("nvmem: sprd: Add Spreadtrum SoCs eFuse support")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Freeman Liu <freeman.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200323150007.7487-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kbuild-robot did find a type error in the min(a, b)
function used by this driver if built for x86_64 or riscv.
Althought it is very unlikely that this driver is built
for those platforms it could be used as a template
for something else and therefore should be correct.
The problem is that we implicitly cast a size_t to
unsigned int inside the implementation of the min() function.
Since size_t may differ on different compilers and
plaforms there may be warnings or not.
So let's use only size_t variables on all platforms.
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: srinivas.kandagatla@linaro.org
Cc: prasannatsmkumar@gmail.com
Cc: malat@debian.org
Cc: paul@crapouillou.net
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-15-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch brings support for the JZ4780 efuse. Currently it only exposes
a read only access to the entire 8K bits efuse memory and nvmem cells.
To fetch for example the MAC address:
dd if=/sys/devices/platform/134100d0.efuse/jz4780-efuse0/nvmem bs=1 skip=34 count=6 status=none | xxd
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-13-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return -EPERM if reg_read is NULL in bin_attr_nvmem_read() or if
reg_write is NULL in bin_attr_nvmem_write().
This prevents NULL dereferences such as the one described in
03cd45d2e2 ("thunderbolt: Prevent crash if non-active NVMem file is
read")
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-10-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Put the write-protect GPIO descriptor in nvmem_release() so that it can
be automatically released when the associated device's reference count
drops to 0.
Fixes: 2a127da461 ("nvmem: add support for the write-protect pin")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Khouloud Touil <ktouil@baylibre.com>
Cc: stable <stable@vger.kernel.org>
[Bartosz: tweak the commit message]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-8-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to free the ida mapping and nvmem struct if the write-protect
GPIO lookup fails.
Fixes: 2a127da461 ("nvmem: add support for the write-protect pin")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-7-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Visibly separate the GPIO request from the previous operation in the
code with a newline.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-6-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add nvmem_cell_read_u64() helper to ease read of an u64 value on consumer
side. This helper is useful on some sunxi platform that has 64 bits data
cells stored in no volatile memory.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-4-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now there are nvmem_cell_read_u16 and nvmem_cell_read_u32.
They are very similar, let's strip out a common part.
And use nvmem_cell_read_common to simplify their implementation.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i.MX8MP has 96 banks with each bank 4 words. And it has different
ctrl register layout, so add new macros for that.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200310132257.23358-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull i2c updates from Wolfram Sang:
"i2c core:
- huge improvements and refactorizations of the Linux I2C
documentation (lots of thanks to Luca for doing it and Jean for the
careful review)
- subsystem wide API conversion to i2c_new_client_device()
- remove obsolete parport-light driver
- smaller core updates (removal of 'extern', enabling more compile
testing, use more helper macros)
- and quite a bunch of driver updates (new IDs, simplifications,
better PM, support of atomic transfers and other improvements)
i2c-mux:
- The main feature is the idle-state rework of the pca954x driver
from Biwen Li
at24 driver:
- minor maintenance: update the license tag, sort headers
- move support for the write-protect pin into nvmem core
- add a reference to the new wp-gpios property in nvmem to at25
bindings
- add support for regulator and pm_runtime control"
* 'i2c/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (91 commits)
i2c: cros-ec-tunnel: Fix ACPI identifier
i2c: cros-ec-tunnel: Fix slave device enumeration
i2c: stm32f7: add PM_SLEEP suspend/resume support
i2c: cadence: Fix wording in i2c-cadence driver
i2c: cadence: Fix power management order of operations
i2c: cadence: Fix error printing in case of defer
i2c: cadence: Handle transfer_size rollover
i2c: i801: Add support for Intel Comet Lake PCH-V
docs: i2c: writing-clients: properly name the stop condition
docs: i2c: i2c-protocol: use same wording as smbus-protocol
docs: i2c: rename sections so the overall picture is clearer
docs: i2c: old-module-parameters: use monospace instead of ""
docs: i2c: old-module-parameters: clarify this is for obsolete kernels
docs: i2c: old-module-parameters: fix internal hyperlink
docs: i2c: instantiating-devices: use monospace for sysfs attributes
docs: i2c: instantiating-devices: rearrange static instatiation
docs: i2c: instantiating-devices: fix internal hyperlink
docs: i2c: smbus-protocol: improve I2C Block transactions description
docs: i2c: smbus-protocol: fix punctuation
docs: i2c: smbus-protocol: fix typo
...
QTI SDAM driver allows PMIC peripherals to access the shared memory
that is available on QTI PMICs.
Use subsys_initcall as PMIC SDAM NV memory is accessed by multiple PMIC
drivers (charger, fuel gauge) to store/restore data across reboots
required during their initialization.
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Signed-off-by: Shyam Kumar Thella <sthella@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200116161100.30637-4-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce ocotp_ctrl_reg to include the low 16bits mask of CTRL
register.
i.MX chips will have different layout of the low 16bits of CTRL
register, so use ocotp_ctrl_reg will make it clean to add new
chip support.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200109104017.6249-4-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i.MX8 fuse word row index represented as one 4-bytes word.
Exp:
- MAC0 address layout in fuse:
offset 708: MAC[3] MAC[2] MAC[1] MAC[0]
offset 709: XX xx MAC[5] MAC[4]
The original code takes row index * 4 as the offset, this
not exactly match i.MX8 fuse map documentation.
So update code the reflect the truth.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200109104017.6249-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SIP number 0xC200000A is for reading, 0xC200000B is for writing.
And the following two args for write are word index, data to write.
Fixes: 885ce72a09 ("nvmem: imx: scu: support write")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200109104017.6249-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nvmem_register() returns a pointer, not a long int. Use ERR_CAST() to
cast the struct gpio_desc pointer to struct nvmem_device.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 2a127da461 ("nvmem: add support for the write-protect pin")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
The write-protect pin handling looks like a standard property that
could benefit other users if available in the core nvmem framework.
Instead of modifying all the memory drivers to check this pin, make
the NVMEM subsystem check if the write-protect GPIO being passed
through the nvmem_config or defined in the device tree and pull it
low whenever writing to the memory.
There was a suggestion for introducing the gpiodesc from pdata, but
as pdata is already removed it could be replaced by adding it to
nvmem_config.
Reference: https://lists.96boards.org/pipermail/dev/2018-August/001056.html
Signed-off-by: Khouloud Touil <ktouil@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo
-----BEGIN PGP SIGNATURE-----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=dk7w
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
Here is the big set of char/misc and other driver patches for 5.5-rc1
Loads of different things in here, this feels like the catch-all of
driver subsystems these days. Full details are in the shortlog, but
nothing major overall, just lots of driver updates and additions.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6ewA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymNXACfebVkDrFOH9EqDgFArPvZ1i9EmZ4AoLbE1Wki
ftJApk+Ov1BT2TvClOza
=cXqg
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc and other driver patches for 5.5-rc1
Loads of different things in here, this feels like the catch-all of
driver subsystems these days. Full details are in the shortlog, but
nothing major overall, just lots of driver updates and additions.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (198 commits)
char: Fix Kconfig indentation, continued
habanalabs: add more protection of device during reset
habanalabs: flush EQ workers in hard reset
habanalabs: make the reset code more consistent
habanalabs: expose reset counters via existing INFO IOCTL
habanalabs: make code more concise
habanalabs: use defines for F/W files
habanalabs: remove prints on successful device initialization
habanalabs: remove unnecessary checks
habanalabs: invalidate MMU cache only once
habanalabs: skip VA block list update in reset flow
habanalabs: optimize MMU unmap
habanalabs: prevent read/write from/to the device during hard reset
habanalabs: split MMU properties to PCI/DRAM
habanalabs: re-factor MMU masks and documentation
habanalabs: type specific MMU cache invalidation
habanalabs: re-factor memory module code
habanalabs: export uapi defines to user-space
habanalabs: don't print error when queues are full
habanalabs: increase max jobs number to 512
...
Newer Rockchip socs like the px30 use a different one-time-programmable
memory controller for things like cpu-id and leakage information,
so add the necessary driver for it.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
[ported from vendor 4.4, converted to clock-bulk API and cleanups]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20191029114240.14905-11-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Spreadtrum eFuse controller is widely used to dump chip ID,
configuration setting, function select and so on, as well as
supporting one-time programming.
Signed-off-by: Freeman Liu <freeman.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20191029114240.14905-8-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If software running before the OCOTP driver is loaded left the
controller with the error status pending, the driver will never
be able to complete the read timing setup. Reset the error status
on probe to make sure the controller is in usable state.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20191029114240.14905-6-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fuse programming from non-secure world is blocked, so we could
only use Arm Trusted Firmware SIP call to let ATF program fuse.
Because there is ECC region that could only be programmed once,
so add a heler in_ecc to check the ecc region.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20191029114240.14905-5-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce HOLE/ECC_REGION flag and in_hole helper to ease the check
of hole region. The ECC_REGION is also introduced here which is
preparing for programming support. ECC_REGION could only be programmed
once, so need take care.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20191029114240.14905-4-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change to use devm_hwspin_lock_request_specific() to help to simplify the
cleanup code for drivers requesting one hwlock. Thus we can remove the
redundant sc27xx_efuse_remove() and platform_set_drvdata().
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20191029114240.14905-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nvmem_device_find provides a way to search for nvmem devices with
the help of a match function simlair to bus_find_device.
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-doc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-rtc@vger.kernel.org
Cc: linux-serial@vger.kernel.org
The secure monitor driver is currently a frankenstein driver which is
registered as a platform driver but its functionality goes through a
global struct accessed by the consumer drivers using exported helper
functions.
Try to tidy up the driver moving the firmware struct into the driver
data and make the consumer drivers referencing the secure-monitor using
a new property in the DT.
Currently only the nvmem driver is using this API so we can fix it in
the same commit.
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Here is the big char/misc driver pull request for 5.4-rc1.
As has been happening in previous releases, more and more individual
driver subsystem trees are ending up in here. Now if that is good or
bad I can't tell, but hopefully it makes your life easier as it's more
of an aggregation of trees together to one merge point for you.
Anyway, lots of stuff in here:
- habanalabs driver updates
- thunderbolt driver updates
- misc driver updates
- coresight and intel_th hwtracing driver updates
- fpga driver updates
- extcon driver updates
- some dma driver updates
- char driver updates
- android binder driver updates
- nvmem driver updates
- phy driver updates
- parport driver fixes
- pcmcia driver fix
- uio driver updates
- w1 driver updates
- configfs fixes
- other assorted driver updates
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXYIT1g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym9lwCgrHZlMMvfYNVm6GQ5ge58JJsVTL4AoNatTcL4
hfVMA6pCHWBjV65xVSf6
=Tijw
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver pull request for 5.4-rc1.
As has been happening in previous releases, more and more individual
driver subsystem trees are ending up in here. Now if that is good or
bad I can't tell, but hopefully it makes your life easier as it's more
of an aggregation of trees together to one merge point for you.
Anyway, lots of stuff in here:
- habanalabs driver updates
- thunderbolt driver updates
- misc driver updates
- coresight and intel_th hwtracing driver updates
- fpga driver updates
- extcon driver updates
- some dma driver updates
- char driver updates
- android binder driver updates
- nvmem driver updates
- phy driver updates
- parport driver fixes
- pcmcia driver fix
- uio driver updates
- w1 driver updates
- configfs fixes
- other assorted driver updates
All of these have been in linux-next for a long time with no reported
issues"
* tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (200 commits)
misc: mic: Use PTR_ERR_OR_ZERO rather than its implementation
habanalabs: correctly cast variable to __le32
habanalabs: show correct id in error print
habanalabs: stop using the acronym KMD
habanalabs: display card name as sensors header
habanalabs: add uapi to retrieve aggregate H/W events
habanalabs: add uapi to retrieve device utilization
habanalabs: Make the Coresight timestamp perpetual
habanalabs: explicitly set the queue-id enumerated numbers
habanalabs: print to kernel log when reset is finished
habanalabs: replace __le32_to_cpu with le32_to_cpu
habanalabs: replace __cpu_to_le32/64 with cpu_to_le32/64
habanalabs: Handle HW_IP_INFO if device disabled or in reset
habanalabs: Expose devices after initialization is done
habanalabs: improve security in Debug IOCTL
habanalabs: use default structure for user input in Debug IOCTL
habanalabs: Add descriptive name to PSOC app status register
habanalabs: Add descriptive names to PSOC scratch-pad registers
habanalabs: create two char devices per ASIC
habanalabs: change device_setup_cdev() to be more generic
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXYAIeQAKCRBiEGxRG/Sl
2/SzAQDEnoNxzV/R5kWFd+2kmFeY3cll0d99KMrWJ8om+kje6QD/cXxZHzFm+T1L
UPF66k76oOODV7cyndjXnTnRXbeCRAM=
=Szby
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"In this cycle we've finally managed to contribute the patch set
sorting out LED naming issues. Besides that there are many changes
scattered among various LED class drivers and triggers.
LED naming related improvements:
- add new 'function' and 'color' fwnode properties and deprecate
'label' property which has been frequently abused for conveying
vendor specific names that have been available in sysfs anyway
- introduce a set of standard LED_FUNCTION* definitions
- introduce a set of standard LED_COLOR_ID* definitions
- add a new {devm_}led_classdev_register_ext() API with the
capability of automatic LED name composition basing on the
properties available in the passed fwnode; the function is
backwards compatible in a sense that it uses 'label' data, if
present in the fwnode, for creating LED name
- add tools/leds/get_led_device_info.sh script for retrieving LED
vendor, product and bus names, if applicable; it also performs
basic validation of an LED name
- update following drivers and their DT bindings to use the new LED
registration API:
- leds-an30259a, leds-gpio, leds-as3645a, leds-aat1290, leds-cr0014114,
leds-lm3601x, leds-lm3692x, leds-lp8860, leds-lt3593, leds-sc27xx-blt
Other LED class improvements:
- replace {devm_}led_classdev_register() macros with inlines
- allow to call led_classdev_unregister() unconditionally
- switch to use fwnode instead of be stuck with OF one
LED triggers improvements:
- led-triggers:
- fix dereferencing of null pointer
- fix a memory leak bug
- ledtrig-gpio:
- GPIO 0 is valid
Drop superseeded apu2/3 support from leds-apu since for apu2+ a newer,
more complete driver exists, based on a generic driver for the AMD
SOCs gpio-controller, supporting LEDs as well other devices:
- drop profile field from priv data
- drop iosize field from priv data
- drop enum_apu_led_platform_types
- drop superseeded apu2/3 led support
- add pr_fmt prefix for better log output
- fix error message on probing failure
Other misc fixes and improvements to existing LED class drivers:
- leds-ns2, leds-max77650:
- add of_node_put() before return
- leds-pwm, leds-is31fl32xx:
- use struct_size() helper
- leds-lm3697, leds-lm36274, leds-lm3532:
- switch to use fwnode_property_count_uXX()
- leds-lm3532:
- fix brightness control for i2c mode
- change the define for the fs current register
- fixes for the driver for stability
- add full scale current configuration
- dt: Add property for full scale current.
- avoid potentially unpaired regulator calls
- move static keyword to the front of declarations
- fix optional led-max-microamp prop error handling
- leds-max77650:
- add of_node_put() before return
- add MODULE_ALIAS()
- Switch to fwnode property API
- leds-as3645a:
- fix misuse of strlcpy
- leds-netxbig:
- add of_node_put() in netxbig_leds_get_of_pdata()
- remove legacy board-file support
- leds-is31fl319x:
- simplify getting the adapter of a client
- leds-ti-lmu-common:
- fix coccinelle issue
- move static keyword to the front of declaration
- leds-syscon:
- use resource managed variant of device register
- leds-ktd2692:
- fix a typo in the name of a constant
- leds-lp5562:
- allow firmware files up to the maximum length
- leds-an30259a:
- fix typo
- leds-pca953x:
- include the right header"
* tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (72 commits)
leds: lm3532: Fix optional led-max-microamp prop error handling
led: triggers: Fix dereferencing of null pointer
leds: ti-lmu-common: Move static keyword to the front of declaration
leds: lm3532: Move static keyword to the front of declarations
leds: trigger: gpio: GPIO 0 is valid
leds: pwm: Use struct_size() helper
leds: is31fl32xx: Use struct_size() helper
leds: ti-lmu-common: Fix coccinelle issue in TI LMU
leds: lm3532: Avoid potentially unpaired regulator calls
leds: syscon: Use resource managed variant of device register
leds: Replace {devm_}led_classdev_register() macros with inlines
leds: Allow to call led_classdev_unregister() unconditionally
leds: lm3532: Add full scale current configuration
dt: lm3532: Add property for full scale current.
leds: lm3532: Fixes for the driver for stability
leds: lm3532: Change the define for the fs current register
leds: lm3532: Fix brightness control for i2c mode
leds: Switch to use fwnode instead of be stuck with OF one
leds: max77650: Switch to fwnode property API
led: triggers: Fix a memory leak bug
...
The email address listed in MODULE_AUTHOR() will be disabled in the
near future. Replace it with my private one.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20190818093345.29647-6-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Amlogic boards store the Ethernet MAC address inside the eFuse. The
Ethernet MAC address uses 6 bytes. The existing logic in
meson_mx_efuse_read() would write beyond the end of the data buffer when
trying to read data with a size that is not aligned to word_size (4
bytes on Meson8, Meson8b and Meson8m2).
Calculate the remaining data to copy inside meson_mx_efuse_read() so
reading 6 bytes doesn't write beyond the end of the data buffer.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20190818093345.29647-5-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Srinivas Kandagatla
Samuel Zou
Michael Auchter
Anson Huang
Rajan Vaja
Baolin Wang
Freeman Liu
H. Nikolaus Schaller
PrasannaKumar Muralidharan
Nicholas Johnson
Khouloud Touil
Bartosz Golaszewski
Yangtao Li
Peng Fan
Linus Torvalds
Anirudh Ghayal
Bitan Biswas
Finley Xiao
Lucas Stach
Baolin Wang
Thomas Bogendoerfer
Carlo Caione
Fugang Duan
Stefan Wahren
Martin Blumenstingl