Граф коммитов

1076 Коммитов

Автор SHA1 Сообщение Дата
Chris Boot 41591b38f5 mmc: block: avoid multiblock reads for the last sector in SPI mode
On some SD cards over SPI, reading with the multiblock read command the last
sector will leave the card in a bad state.

Remove last sectors from the multiblock reading cmd.

Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-10-09 09:23:00 +02:00
Marek Szyprowski 1b09d9c232 mmc: slot-gpio: Fix debounce time to use miliseconds again
The debounce value passed to mmc_gpiod_request_cd() function is in
microseconds, but msecs_to_jiffies() requires the value to be in
miliseconds to properly calculate the delay, so adjust the value stored
in cd_debounce_delay_ms context entry.

Fixes: 1d71926bbd ("mmc: core: Fix debounce time to use microseconds")
Fixes: bfd694d5e2 ("mmc: core: Add tunable delay before detecting card
after card is inserted")
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-09-28 17:43:48 +02:00
Tony Lindgren 1d71926bbd mmc: core: Fix debounce time to use microseconds
The debounce value in device tree is in milliseconds but needs to be in
microseconds for mmc_gpiod_request_cd().

Fixes: bfd694d5e2 ("mmc: core: Add tunable delay before detecting card
after card is inserted")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-09-27 00:39:32 +02:00
Adrian Hunter 26caddf274 mmc: block: Fix unsupported parallel dispatch of requests
The mmc block driver does not support parallel dispatch of requests. In
normal circumstances, all requests are anyway funneled through a single
work item, so parallel dispatch never happens. However it can happen if
there is no elevator.

Fix that by detecting if a dispatch is in progress and returning busy
(BLK_STS_RESOURCE) in that case

Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-08-21 16:12:41 +02:00
Hongjie Fang 7f38abf220 mmc: core: improve reasonableness of bus width setting for HS400es
mmc_select_hs400es() calls mmc_select_bus_width() which will continue
to set 4bit transfer mode if fail to set 8bit mode. The bus width
should not be set to 4bit in HS400es.

When fail to set 8bit mode, need return error directly for HS400es.

Signed-off-by: Hongjie Fang <hongjiefang@asrmicro.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-08-01 14:15:28 +02:00
Ulf Hansson 29772f8a73 mmc: core: Drop the unused mmc_power_save|restore_host()
The last user of mmc_power_save|restore_host() APIs is gone, hence let's
drop them. Drop also the corresponding bus_ops callback,
->power_save|restore() as those becomes redundant.

Cc: Tony Lindgren <tony@atomide.com>
Cc: Eyal Reizer <eyalreizer@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-07-16 11:21:45 +02:00
Simon Horman ba6c7ac3a2 mmc: core: more fine-grained hooks for HS400 tuning
This adds two new HS400 tuning operations:
* hs400_downgrade
* hs400_complete

These supplement the existing HS400 operation:
* prepare_hs400_tuning

This is motivated by a requirement of Renesas SDHI for the following:
1. Disabling SCC before selecting to HS if selection of HS400 has occurred.
   This can be done in an implementation of prepare_hs400_tuning_downgrade
2. Updating registers after switching to HS400
   This can be done in an implementation of complete_hs400_tuning

If hs400_downgrade or hs400_complete are not implemented then they are not
called. Thus means there should be no affect for existing drivers as none
implemt these ops.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-07-16 11:21:45 +02:00
Shawn Lin a94a7483a9 mmc: core: Adjust and reuse the macro of R1_STATUS(x)
R1_STATUS(x) now is only used by ioctl_rpmb_card_status_poll(),
which checks all bits as possible. But according to the spec,
bit 17 and bit 18 should be ignored, as well bit 14 which is
reserved(must be set to 0) quoting from the spec and these rule
apply to all places checking the device status. So change
its checking from 0xFFFFE000 to 0xFFF9A000.

As a bonus, we reuse it for mmc_do_erase() as well as
mmc_switch_status_error().
(1) Currently mmc_switch_status_error() doesn't check bit 25, but
it means device is locked but not unlocked by CMD42 prior to any
operations which need check busy, which is also not allowed.
(2) mmc_do_erase() also forgot to to check bit 15, WP_ERASE_SKIP.
The spec says "Only partial address space was erased due to existing
write protected blocks.", which obviously means we should fail this I/O.
Otherwise, the partial erased data stored in nonvalatile flash violates
the data integrity from the view of I/O owner, which probably confuse
it when further used.

So reusing R1_STATUS for them not only improve the readability but also
slove real problems.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-07-16 11:21:45 +02:00
Anson Huang 60feca8f59 mmc: core: cd_label must be last entry of mmc_gpio struct
commit bfd694d5e2 ("mmc: core: Add tunable delay
before detecting card after card is inserted") adds
"u32 cd_debounce_delay_ms" to the last of mmc_gpio
struct and cause "char cd_label[0]" NOT work as string
pointer of card detect label, when "cat /proc/interrupts",
the devname for card detect gpio is incorrect as below:

144:          0  gpio-mxc  22 Edge      ▒
161:          0  gpio-mxc   7 Edge      ▒

Move the cd_label field down to fix this, and drop the
zero from the array size to prevent future similar bugs,
the result is correct as below:

144:          0  gpio-mxc  22 Edge      2198000.mmc cd
161:          0  gpio-mxc   7 Edge      2190000.mmc cd

Fixes: bfd694d5e2 ("mmc: core: Add tunable delay before detecting card after card is inserted")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-07-03 07:12:35 +02:00
Linus Torvalds f60342fac9 MMC core:
- Decrease polling rate for erase/trim/discard
  - Allow non-sleeping GPIOs for card detect
  - Improve mmc block removal path
  - Enable support for mmc_sw_reset() for SDIO cards
  - Add mmc_sw_reset() to allow users to do a soft reset of the card
  - Allow power delay to be tunable via DT
  - Allow card detect debounce delay to be tunable via DT
  - Enable new quirk to limit clock rate for Marvell 8887 chip
  - Don't show eMMC RPMB and BOOT areas in /proc/partitions
  - Add capability to avoid 3.3V signaling for fragile HWs
 
 MMC host:
  - Improve/fixup support for handle highmem pages
  - Remove depends on HAS_DMA in case of platform dependency
  - mvsdio: Enable support for erase/trim/discard
  - rtsx_usb: Enable support for erase/trim/discard
  - renesas_sdhi: Fix WP logic regressions
  - renesas_sdhi: Add r8a77965 support
  - renesas_sdhi: Add R8A77980 to whitelist
  - meson: Add optional support for device reset
  - meson: Add support for the Meson-AXG platform
  - dw_mmc: Add new driver for BlueField DW variant
  - mediatek: Add support for 64G DRAM DMA
  - sunxi: Deploy runtime PM support
  - jz4740: Add support for JZ4780
  - jz4740: Enable support for DT based platforms
  - sdhci: Various improvement to timeout handling
  - sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
  - sdhci-omap: Add support for controller in k2g SoC
  - sdhci-omap: Add workarounds for a couple of Erratas
  - sdhci-omap: Enable support for generic sdhci DT properties
  - sdhci-cadence: Re-send tune request to deal with errata
  - sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
  - sdhci-pci: Avoid 3.3V signaling on some NI 904x
  - sdhci-esdhc-imx: Use watermark levels for PIO access
  - sdhci-msm: Improve card detection handling
  - sdhci-msm: Add support voltage pad switching
 -----BEGIN PGP SIGNATURE-----
 
 iQJLBAABCgA1FiEEugLDXPmKSktSkQsV/iaEJXNYjCkFAlsWMJUXHHVsZi5oYW5z
 c29uQGxpbmFyby5vcmcACgkQ/iaEJXNYjCkWhw/9GdsKWGAezGYcBC9fBKVbZgvl
 Mu7kTebyQy1N7kbIVD7sBz2ila1O2DhVI9SVS7lVhzFwrG4Hup0szb/mjEQgiOAi
 +S2EjKRD3+9sA612fi1uWY+2cXoQiwCHhFZsCS5deL4pYspebzuYRNO5vZD7QlN8
 vLHZ85yxBtMSiysDUTRm9MH2EXb9j6PfrHnVKj0ih112U/ip4PZVc7zHGBZq9zzy
 6WSUMYBe2d1jajJ6MS3gf5Vrp53mz2OLkxKRCtMgut7YOwLZ8biKVa3G69ruQTm8
 jqrMoNrZnhO3aT/1kassCE4ygoXewMZPhYq8k24PcaihR3o/tVI1dlb4Zz70cBb8
 AGAdmdzu1sDEzY6KkSVTZ5IaxQo9SNANste/O/LfsOxHWkWxBQ6H0EeqMdt+W7of
 A0zGKTQrcTFhxzA9OeX3aZwZhjcipQlf8TWnI5+ayPY/UKwMhvWNCTMQtTJAhqBh
 mS7Uk5qd7OSJZTzVYrfLZ2ZOQKhtMbD9lAza/9Ldy5j5QDscLmxmhLOP0yuKI2Zp
 92N3JPIGzfK4aKGCLKSA3KhYwuwaicwsXqfJV+cPz9fFtNs8WdHqyU+nslD0Oxm4
 v3QZKPJa3LWCezPvWGSSTGLEgOvJtLQtJBefX1Hm6sxLbY12aBgu/iNp5UckGlzW
 7zaWXtH8nzYlBKsXf/8=
 =MwCT
 -----END PGP SIGNATURE-----

Merge tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Decrease polling rate for erase/trim/discard
   - Allow non-sleeping GPIOs for card detect
   - Improve mmc block removal path
   - Enable support for mmc_sw_reset() for SDIO cards
   - Add mmc_sw_reset() to allow users to do a soft reset of the card
   - Allow power delay to be tunable via DT
   - Allow card detect debounce delay to be tunable via DT
   - Enable new quirk to limit clock rate for Marvell 8887 chip
   - Don't show eMMC RPMB and BOOT areas in /proc/partitions
   - Add capability to avoid 3.3V signaling for fragile HWs

  MMC host:
   - Improve/fixup support for handle highmem pages
   - Remove depends on HAS_DMA in case of platform dependency
   - mvsdio: Enable support for erase/trim/discard
   - rtsx_usb: Enable support for erase/trim/discard
   - renesas_sdhi: Fix WP logic regressions
   - renesas_sdhi: Add r8a77965 support
   - renesas_sdhi: Add R8A77980 to whitelist
   - meson: Add optional support for device reset
   - meson: Add support for the Meson-AXG platform
   - dw_mmc: Add new driver for BlueField DW variant
   - mediatek: Add support for 64G DRAM DMA
   - sunxi: Deploy runtime PM support
   - jz4740: Add support for JZ4780
   - jz4740: Enable support for DT based platforms
   - sdhci: Various improvement to timeout handling
   - sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
   - sdhci-omap: Add support for controller in k2g SoC
   - sdhci-omap: Add workarounds for a couple of Erratas
   - sdhci-omap: Enable support for generic sdhci DT properties
   - sdhci-cadence: Re-send tune request to deal with errata
   - sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
   - sdhci-pci: Avoid 3.3V signaling on some NI 904x
   - sdhci-esdhc-imx: Use watermark levels for PIO access
   - sdhci-msm: Improve card detection handling
   - sdhci-msm: Add support voltage pad switching"

* tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (104 commits)
  mmc: renesas_sdhi: really fix WP logic regressions
  mmc: mvsdio: Enable MMC_CAP_ERASE
  mmc: mvsdio: Respect card busy time out from mmc core
  mmc: sdhci-msm: Remove NO_CARD_NO_RESET quirk
  mmc: sunxi: Use ifdef rather than __maybe_unused
  mmc: mxmmc: Use ifdef rather than __maybe_unused
  mmc: mxmmc: include linux/highmem.h
  mmc: sunxi: mark PM functions as __maybe_unused
  mmc: Throttle calls to MMC_SEND_STATUS during mmc_do_erase()
  mmc: au1xmmc: handle highmem pages
  mmc: Allow non-sleeping GPIO cd
  mmc: sdhci-*: Don't emit error msg if sdhci_add_host() fails
  mmc: sd: Define name for default speed dtr
  mmc: core: Move calls to ->prepare_hs400_tuning() closer to mmc code
  mmc: sdhci-xenon: use match_string() helper
  mmc: wbsd: handle highmem pages
  mmc: ushc: handle highmem pages
  mmc: mxcmmc: handle highmem pages
  mmc: atmel-mci: use sg_copy_{from,to}_buffer
  mmc: android-goldfish: use sg_copy_{from,to}_buffer
  ...
2018-06-05 16:11:43 -07:00
Linus Torvalds 3c89adb0d1 Power management updates for 4.18-rc1
These include a significant update of the generic power domains (genpd)
 and Operating Performance Points (OPP) frameworks, mostly related to
 the introduction of power domain performance levels, cpufreq updates
 (new driver for Qualcomm Kryo processors, updates of the existing
 drivers, some core fixes, schedutil governor improvements), PCI power
 management fixes, ACPI workaround for EC-based wakeup events handling
 on resume from suspend-to-idle, and major updates of the turbostat
 and pm-graph utilities.
 
 Specifics:
 
  - Introduce power domain performance levels into the the generic
    power domains (genpd) and Operating Performance Points (OPP)
    frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
 
  - Fix two issues in the runtime PM framework related to the
    initialization and removal of devices using device links (Ulf
    Hansson).
 
  - Clean up the initialization of drivers for devices in PM domains
    (Ulf Hansson, Geert Uytterhoeven).
 
  - Fix a cpufreq core issue related to the policy sysfs interface
    causing CPU online to fail for CPUs sharing one cpufreq policy in
    some situations (Tao Wang).
 
  - Make it possible to use platform-specific suspend/resume hooks
    in the cpufreq-dt driver and make the Armada 37xx DVFS use that
    feature (Viresh Kumar, Miquel Raynal).
 
  - Optimize policy transition notifications in cpufreq (Viresh Kumar).
 
  - Improve the iowait boost mechanism in the schedutil cpufreq
    governor (Patrick Bellasi).
 
  - Improve the handling of deferred frequency updates in the
    schedutil cpufreq governor (Joel Fernandes, Dietmar Eggemann,
    Rafael Wysocki, Viresh Kumar).
 
  - Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
 
  - Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
    Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman,
    Viresh Kumar).
 
  - Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag
    set and update stale comments in the PCI core PM code (Rafael
    Wysocki).
 
  - Work around an issue related to the handling of EC-based wakeup
    events in the ACPI PM core during resume from suspend-to-idle if
    the EC has been put into the low-power mode (Rafael Wysocki).
 
  - Improve the handling of wakeup source objects in the PM core (Doug
    Berger, Mahendran Ganesh, Rafael Wysocki).
 
  - Update the driver core to prevent deferred probe from breaking
    suspend/resume ordering (Feng Kan).
 
  - Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
    Wysocki).
 
  - Make the core suspend/resume code and cpufreq support the RT patch
    (Sebastian Andrzej Siewior, Thomas Gleixner).
 
  - Consolidate the PM QoS handling in cpuidle governors (Rafael
    Wysocki).
 
  - Fix a possible crash in the hibernation core (Tetsuo Handa).
 
  - Update the rockchip-io Adaptive Voltage Scaling (AVS) driver
    (David Wu).
 
  - Update the turbostat utility (fixes, cleanups, new CPU IDs, new
    command line options, built-in "Low Power Idle" counters support,
    new POLL and POLL% columns) and add an entry for it to MAINTAINERS
    (Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
    Prarit Bhargava, Srinivas Pandruvada).
 
  - Update the pm-graph to version 5.1 (Todd Brandt).
 
  - Update the intel_pstate_tracer utility (Doug Smythies).
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJbFRzjAAoJEILEb/54YlRxREQQAKD7IjnLA86ZDkmwiwzFa9Cz
 OJ0qlKAcMZGjeWH6LYq7lqWtaJ5PcFkBwNB4sRyKFdGPQOX3Ph8ZzILm2j8hhma4
 Azn9632P6CoYHABa8Vof+A1BZ/j0aWtvtJEfqXhtF6rAYyWQlF0UmOIRsMs+54a+
 Z/w4WuLaX8qYq3JlR60TogNtTIbdUjkjfvxMGrE9OSQ8n4oEhqoF/v0WoTHYLpWw
 fu81M378axOu0Sgq1ZQ8GPUdblUqIO97iWwF7k2YUl7D9n5dm4wOhXDz3CLI8Cdb
 RkoFFdp8bJIthbc5desKY2XFU1ClY8lxEVMXewFzTGwWMw0OyWgQP0/ZiG+Mujq3
 CSbstg8GGpbwQoWU+VrluYa0FtqofV2UaGk1gOuPaojMqaIchRU4Nmbd2U6naNwp
 XN7A1DzrOVGEt0ny8ztKH2Oqmj+NOCcRsChlYzdhLQ1wlqG54iCGwAML2ZJF9/Nw
 0Sx8hm6eyWLzjSa0L384Msb+v5oqCoac66gPHCl2x7W+3F+jmqx1KbmkI2SRNUAL
 7CS9lcImpvC4uZB54Aqya104vfqHiDse7WP0GrKqOmNVucD7hYCPiq/pycLwez+b
 V3zLyvly8PsuBIa4AOQGGiK45HGpaKuB4TkRqRyFO0Fb5uL1M+Ld6kJiWlacl4az
 STEUjY/90SRQvX3ocGyB
 =wqBV
 -----END PGP SIGNATURE-----

Merge tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull power management updates from Rafael Wysocki:
 "These include a significant update of the generic power domains
  (genpd) and Operating Performance Points (OPP) frameworks, mostly
  related to the introduction of power domain performance levels,
  cpufreq updates (new driver for Qualcomm Kryo processors, updates of
  the existing drivers, some core fixes, schedutil governor
  improvements), PCI power management fixes, ACPI workaround for
  EC-based wakeup events handling on resume from suspend-to-idle, and
  major updates of the turbostat and pm-graph utilities.

  Specifics:

   - Introduce power domain performance levels into the the generic
     power domains (genpd) and Operating Performance Points (OPP)
     frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).

   - Fix two issues in the runtime PM framework related to the
     initialization and removal of devices using device links (Ulf
     Hansson).

   - Clean up the initialization of drivers for devices in PM domains
     (Ulf Hansson, Geert Uytterhoeven).

   - Fix a cpufreq core issue related to the policy sysfs interface
     causing CPU online to fail for CPUs sharing one cpufreq policy in
     some situations (Tao Wang).

   - Make it possible to use platform-specific suspend/resume hooks in
     the cpufreq-dt driver and make the Armada 37xx DVFS use that
     feature (Viresh Kumar, Miquel Raynal).

   - Optimize policy transition notifications in cpufreq (Viresh Kumar).

   - Improve the iowait boost mechanism in the schedutil cpufreq
     governor (Patrick Bellasi).

   - Improve the handling of deferred frequency updates in the schedutil
     cpufreq governor (Joel Fernandes, Dietmar Eggemann, Rafael Wysocki,
     Viresh Kumar).

   - Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).

   - Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
     Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman, Viresh
     Kumar).

   - Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag set
     and update stale comments in the PCI core PM code (Rafael Wysocki).

   - Work around an issue related to the handling of EC-based wakeup
     events in the ACPI PM core during resume from suspend-to-idle if
     the EC has been put into the low-power mode (Rafael Wysocki).

   - Improve the handling of wakeup source objects in the PM core (Doug
     Berger, Mahendran Ganesh, Rafael Wysocki).

   - Update the driver core to prevent deferred probe from breaking
     suspend/resume ordering (Feng Kan).

   - Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
     Wysocki).

   - Make the core suspend/resume code and cpufreq support the RT patch
     (Sebastian Andrzej Siewior, Thomas Gleixner).

   - Consolidate the PM QoS handling in cpuidle governors (Rafael
     Wysocki).

   - Fix a possible crash in the hibernation core (Tetsuo Handa).

   - Update the rockchip-io Adaptive Voltage Scaling (AVS) driver (David
     Wu).

   - Update the turbostat utility (fixes, cleanups, new CPU IDs, new
     command line options, built-in "Low Power Idle" counters support,
     new POLL and POLL% columns) and add an entry for it to MAINTAINERS
     (Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
     Prarit Bhargava, Srinivas Pandruvada).

   - Update the pm-graph to version 5.1 (Todd Brandt).

   - Update the intel_pstate_tracer utility (Doug Smythies)"

* tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (128 commits)
  tools/power turbostat: update version number
  tools/power turbostat: Add Node in output
  tools/power turbostat: add node information into turbostat calculations
  tools/power turbostat: remove num_ from cpu_topology struct
  tools/power turbostat: rename num_cores_per_pkg to num_cores_per_node
  tools/power turbostat: track thread ID in cpu_topology
  tools/power turbostat: Calculate additional node information for a package
  tools/power turbostat: Fix node and siblings lookup data
  tools/power turbostat: set max_num_cpus equal to the cpumask length
  tools/power turbostat: if --num_iterations, print for specific number of iterations
  tools/power turbostat: Add Cannon Lake support
  tools/power turbostat: delete duplicate #defines
  x86: msr-index.h: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
  tools/power turbostat: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
  tools/power turbostat: add POLL and POLL% column
  tools/power turbostat: Fix --hide Pk%pc10
  tools/power turbostat: Build-in "Low Power Idle" counters support
  tools/power turbostat: Don't make man pages executable
  tools/power turbostat: remove blank lines
  tools/power turbostat: a small C-states dump readability immprovement
  ...
2018-06-05 09:38:39 -07:00
Linus Torvalds cf626b0da7 Merge branch 'hch.procfs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull procfs updates from Al Viro:
 "Christoph's proc_create_... cleanups series"

* 'hch.procfs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (44 commits)
  xfs, proc: hide unused xfs procfs helpers
  isdn/gigaset: add back gigaset_procinfo assignment
  proc: update SIZEOF_PDE_INLINE_NAME for the new pde fields
  tty: replace ->proc_fops with ->proc_show
  ide: replace ->proc_fops with ->proc_show
  ide: remove ide_driver_proc_write
  isdn: replace ->proc_fops with ->proc_show
  atm: switch to proc_create_seq_private
  atm: simplify procfs code
  bluetooth: switch to proc_create_seq_data
  netfilter/x_tables: switch to proc_create_seq_private
  netfilter/xt_hashlimit: switch to proc_create_{seq,single}_data
  neigh: switch to proc_create_seq_data
  hostap: switch to proc_create_{seq,single}_data
  bonding: switch to proc_create_seq_data
  rtc/proc: switch to proc_create_single_data
  drbd: switch to proc_create_single
  resource: switch to proc_create_seq_data
  staging/rtl8192u: simplify procfs code
  jfs: simplify procfs code
  ...
2018-06-04 10:00:01 -07:00
Linus Torvalds f459c34538 for-4.18/block-20180603
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABCAAGBQJbFIrHAAoJEPfTWPspceCm2+kQAKo7o7HL30aRxJYu+gYafkuW
 PV47zr3e4vhMDEzDaMsh1+V7I7bm3uS+NZu6cFbcV+N9KXFpeb4V4Hvvm5cs+OC3
 WCOBi4eC1h4qnDQ3ZyySrCMN+KHYJ16pZqddEjqw+fhVudx8i+F+jz3Y4ZMDDc3q
 pArKZvjKh2wEuYXUMFTjaXY46IgPt+er94OwvrhyHk+4AcA+Q/oqSfSdDahUC8jb
 BVR3FV4I3NOHUaru0RbrUko13sVZSboWPCIFrlTDz8xXcJOnVHzdVS1WLFDXLHnB
 O8q9cADCfa4K08kz68RxykcJiNxNvz5ChDaG0KloCFO+q1tzYRoXLsfaxyuUDg57
 Zd93OFZC6hAzXdhclDFIuPET9OQIjDzwphodfKKmDsm3wtyOtydpA0o7JUEongp0
 O1gQsEfYOXmQsXlo8Ot+Z7Ne/HvtGZ91JahUa/59edxQbcKaMrktoyQsQ/d1nOEL
 4kXID18wPcFHWRQHYXyVuw6kbpRtQnh/U2m1eenSZ7tVQHwoe6mF3cfSf5MMseak
 k8nAnmsfEvOL4Ar9ftg61GOrImaQlidxOC2A8fmY5r0Sq/ZldvIFIZizsdTTCcni
 8SOTxcQowyqPf5NvMNQ8cKqqCJap3ppj4m7anZNhbypDIF2TmOWsEcXcMDn4y9on
 fax14DPLo59gBRiPCn5f
 =nga/
 -----END PGP SIGNATURE-----

Merge tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block

Pull block updates from Jens Axboe:

 - clean up how we pass around gfp_t and
   blk_mq_req_flags_t (Christoph)

 - prepare us to defer scheduler attach (Christoph)

 - clean up drivers handling of bounce buffers (Christoph)

 - fix timeout handling corner cases (Christoph/Bart/Keith)

 - bcache fixes (Coly)

 - prep work for bcachefs and some block layer optimizations (Kent).

 - convert users of bio_sets to using embedded structs (Kent).

 - fixes for the BFQ io scheduler (Paolo/Davide/Filippo)

 - lightnvm fixes and improvements (Matias, with contributions from Hans
   and Javier)

 - adding discard throttling to blk-wbt (me)

 - sbitmap blk-mq-tag handling (me/Omar/Ming).

 - remove the sparc jsflash block driver, acked by DaveM.

 - Kyber scheduler improvement from Jianchao, making it more friendly
   wrt merging.

 - conversion of symbolic proc permissions to octal, from Joe Perches.
   Previously the block parts were a mix of both.

 - nbd fixes (Josef and Kevin Vigor)

 - unify how we handle the various kinds of timestamps that the block
   core and utility code uses (Omar)

 - three NVMe pull requests from Keith and Christoph, bringing AEN to
   feature completeness, file backed namespaces, cq/sq lock split, and
   various fixes

 - various little fixes and improvements all over the map

* tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block: (196 commits)
  blk-mq: update nr_requests when switching to 'none' scheduler
  block: don't use blocking queue entered for recursive bio submits
  dm-crypt: fix warning in shutdown path
  lightnvm: pblk: take bitmap alloc. out of critical section
  lightnvm: pblk: kick writer on new flush points
  lightnvm: pblk: only try to recover lines with written smeta
  lightnvm: pblk: remove unnecessary bio_get/put
  lightnvm: pblk: add possibility to set write buffer size manually
  lightnvm: fix partial read error path
  lightnvm: proper error handling for pblk_bio_add_pages
  lightnvm: pblk: fix smeta write error path
  lightnvm: pblk: garbage collect lines with failed writes
  lightnvm: pblk: rework write error recovery path
  lightnvm: pblk: remove dead function
  lightnvm: pass flag on graceful teardown to targets
  lightnvm: pblk: check for chunk size before allocating it
  lightnvm: pblk: remove unnecessary argument
  lightnvm: pblk: remove unnecessary indirection
  lightnvm: pblk: return NVM_ error on failed submission
  lightnvm: pblk: warn in case of corrupted write buffer
  ...
2018-06-04 07:58:06 -07:00
Rafael J. Wysocki 5b550c92d7 Merge branch 'pm-domains'
* pm-domains:
  PM / domains: Improve wording of dev_pm_domain_attach() comment
  PM / Domains: Don't return -EEXIST at attach when PM domain exists
  spi: Respect all error codes from dev_pm_domain_attach()
  soundwire: Respect all error codes from dev_pm_domain_attach()
  mmc: sdio: Respect all error codes from dev_pm_domain_attach()
  i2c: Respect all error codes from dev_pm_domain_attach()
  driver core: Respect all error codes from dev_pm_domain_attach()
  amba: Respect all error codes from dev_pm_domain_attach()
  PM / Domains: Allow a better error handling of dev_pm_domain_attach()
  PM / Domains: Check for existing PM domain in dev_pm_domain_attach()
  PM / Domains: Drop redundant code in genpd while attaching devices
  PM / Domains: Drop comment in genpd about legacy Samsung DT binding
  PM / Domains: Fix error path during attach in genpd
2018-06-04 10:40:33 +02:00
Christoph Hellwig ad73d6fead mmc: complete requests from ->timeout
By completing the request entirely in the driver we can remove the
BLK_EH_HANDLED return value and thus the split responsibility between the
driver and the block layer that has been causing trouble.

[While this keeps existing behavior it seems to mismatch the comment,
 maintainers please chime in!]

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-05-29 08:59:21 -06:00
Martin Hicks 833b51170f mmc: Throttle calls to MMC_SEND_STATUS during mmc_do_erase()
This drastically reduces the rate at which the MMC_SEND_STATUS cmd polls
for completion of the MMC Erase operation.  The patch does this by adding
a backoff sleep that starts by sleeping for short intervals (128-256us),
and ramps up to sleeping for 32-64ms.

Even on very quickly completing erase operations, the loop iterates a few
times, so not too much extra latency is added to these commands.

For long running discard operarations, like a full-device secure discard,
this change drops the interrupt rates on my single-core NXP I.MX6UL from
45000/s to about 20/s, and greatly improves system responsiveness.

Signed-off-by: Martin Hicks <mort@bork.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-29 12:24:26 +02:00
Evan Green 52af318c93 mmc: Allow non-sleeping GPIO cd
This change uses the appropriate _cansleep or non-sleeping API for
reading GPIO card detect state. This allows users with GPIOs that
never sleep to avoid a warning when certain quirks are present.

The sdhci controller has an SDHCI_QUIRK_NO_CARD_NO_RESET, which
indicates that a controller will not reset properly if no card is
inserted. With this quirk enabled, mmc_get_cd_gpio is called in
several places with a spinlock held and interrupts disabled.
gpiod_get_raw_value_cansleep is not happy with this situation,
and throws out a warning.

For boards that a) use controllers that have this quirk, and b) wire
card detect up to a GPIO that doesn't sleep, this is a spurious warning.
This change silences that warning, at the cost of pushing this problem
down to users that have sleeping GPIOs and controllers with this quirk.

Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-29 12:24:26 +02:00
Ulf Hansson c8a4e30d9a mmc: core: Move calls to ->prepare_hs400_tuning() closer to mmc code
Move the calls to ->prepare_hs400_tuning(), from mmc_retune() into
mmc_hs400_to_hs200(), as it better belongs there, rather than being generic
to all type of cards.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
2018-05-29 12:24:26 +02:00
Ulf Hansson 8603f1e838 Merge branch 'fixes' into next 2018-05-21 15:49:25 +02:00
Shawn Lin 65f9e20e0d mmc: block: Don't switch to the same partition type in mmc_blk_remove()
It's pointless to switch and trace partition type if the current
selected device partition is the same with that one. Moreover, cycled
claiming host associated with mmc_blk_part_switch() could make
mmc_blk_remove() end up waiting for grabbing the context if it's
occupied, which lead requests could still hit the low-level drivers,
if an asynchronous unbind for host drivers happened, as the card hasn't
been set removed in the remove path.

So a simple dd in background:
dd if=/dev/mmcblk0 of=/dev/null bs=512k count=100000 &

and doing unbind then:
echo fe320000.dwmmc > /sys/bus/platform/drivers/dwmmc_rockchip/unbind

could make the console stuck for quite a while depending on the
numbers of requests.

Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-21 15:49:18 +02:00
Mathieu Malaterre b25b750df9 mmc: block: propagate correct returned value in mmc_rpmb_ioctl
In commit 97548575be ("mmc: block: Convert RPMB to a character device") a
new function `mmc_rpmb_ioctl` was added. The final return is simply
returning a value of `0` instead of propagating the correct return code.

Discovered during a compilation with W=1, silence the following gcc warning

drivers/mmc/core/block.c:2470:6: warning: variable ‘ret’ set but not used
[-Wunused-but-set-variable]

Signed-off-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 97548575be ("mmc: block: Convert RPMB to a character device")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-21 10:57:59 +02:00
Shawn Lin 6d796c68cd mmc: core: add tunable delay waiting for power to be stable
The hard-coded 10ms delay in mmc_power_up came from
commit 79bccc5aef ("mmc: increase power up delay"), which said "The TI
controller on Toshiba Tecra M5 needs more time to power up or the cards
will init incorrectly or not at all." But it's too engineering solution
for a special board but force all platforms to wait for that long time,
especially painful for mmc_power_up for eMMC when booting.

However, it's added since 2009, and we can't tell if other platforms
benefit from it. But in practise, the modern hardware are most likely to
have a stable power supply with 1ms after setting it for no matter PMIC
or discrete power. And more importnatly, most regulators implement the
callback of ->set_voltage_time_sel() for regulator core to wait for
specific period of time for the power supply to be stable, which means
once regulator_set_voltage_* return, the power should reach the the
minimum voltage that works for initialization. Of course, if there
are some other ways for host to power the card, we should allow them
to argue a suitable delay as well.

With this patch, we could assign the delay from firmware, or we could
assigne it via ->set_ios() callback from host drivers.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-21 10:38:50 +02:00
Christoph Hellwig 8a8dcabffb tty: replace ->proc_fops with ->proc_show
Just set up the show callback in the tty_operations, and use
proc_create_single_data to create the file without additional
boilerplace code.

Signed-off-by: Christoph Hellwig <hch@lst.de>
2018-05-16 07:24:30 +02:00
Ulf Hansson d23fc022c5 mmc: sdio: Respect all error codes from dev_pm_domain_attach()
The limitation of being able to check only for -EPROBE_DEFER from
dev_pm_domain_attach() has been removed. Hence let's respect all error
codes and bail out accordingly.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-05-14 22:58:45 +02:00
Christoph Hellwig ff005a0662 block: sanitize blk_get_request calling conventions
Switch everyone to blk_get_request_flags, and then rename
blk_get_request_flags to blk_get_request.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-05-14 08:55:12 -06:00
Ulf Hansson 3ce7f76ff9 mmc: core: Drop unused define for timeout
MMC_CORE_TIMEOUT_MS isn't being used no more, let's drop it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-08 09:45:33 +02:00
Ulf Hansson 7405df4c79 mmc: core: Implement ->sw_reset bus ops for SDIO
Let's implement the ->sw_reset() bus ops to allow SDIO func drivers, in
particular, to make a SW reset without doing a full power cycle of the SDIO
card.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2018-05-08 09:33:56 +02:00
Ulf Hansson 508c9864cc mmc: core: Share internal function to set initial signal voltage
Move the corresponding code for setting the initial signal voltage, from
mmc_power_up() into a new function, mmc_set_initial_signal_voltage().

Make the function internally available to the mmc core, as to allow the
following changes to make use of it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2018-05-08 09:33:50 +02:00
Ulf Hansson 1433269c4d mmc: core: Export a function mmc_sw_reset() to allow soft reset of cards
It's rather common that a firmware is loaded into an SDIO func device
memory, by the corresponding SDIO func driver during ->probe() time.

However, to actually start running the new firmware, sometimes a soft reset
(no power cycle) and a re-initialization of the card is needed. This is for
example the case with the Espressif ESP8089 WiFi chips, when connected to
an SDIO interface.

To cope with this scenario, let's add a new exported function,
mmc_sw_reset(), which may be called when a soft reset and re-initialization
of the card are needed.

The mmc_sw_reset() is implemented on top of a new bus ops callback, similar
to how the mmc_hw_reset() has been implemented.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2018-05-08 09:33:42 +02:00
Ulf Hansson 3a3db6030b mmc: core: Rename ->reset() bus ops to ->hw_reset()
The bus ops ->reset() executes a full HW reset of the card, as the calling
function mmc_hw_reset() also indicates by its name. Let's convert to follow
the similar names, for both the bus ops callback and for the corresponding
bus ops functions, as to clarify the purpose of code.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2018-05-08 09:33:29 +02:00
Ulf Hansson fb09f44e29 mmc: core: Re-factor some code for SDIO re-initialization
The mmc_sdio_init_card() function has a couple of callers. In the
re-initialization cases, some additional reset commands are issued before
mmc_sdio_init_card() is called. As these additional reset commands are the
same, let's move these into a new static function, mmc_sdio_reinit_card()
and call mmc_sdio_init_card() from there. In this way we avoid the open
coding.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
2018-05-08 09:32:36 +02:00
Shawn Lin bfd694d5e2 mmc: core: Add tunable delay before detecting card after card is inserted
Allow to use tunable delay before detecting card after card is inserted,
which either comes from firmware node, or comes from debounce value
passed on to mmc_gpiod_request_cd(). If the platform doesn't support
debounce, then we fall back to use the debounce period as the delay,
otherwise, it behaves the same as before that a HW debounce(if set) plus
a 200ms hardcode delay before detecting the card.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 10:33:52 +02:00
Kyle Roeschley 247cfe5355 mmc: core: Add capability to avoid 3.3V signaling
Some SD host controllers cannot handle extended use of 3.3V signaling.
To accommodate these controllers, add a capability that requires us to
negotiate the voltage down from 3.3V during card initialization.

Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Jennifer Dahm <jennifer.dahm@ni.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:44 +02:00
Diwakar Sharma 8ccd66f258 mmc: core: sdio: Set SDIO clock of SDR104 to 150MHz for Marvell 8887 chip
This patch uses limit clock rate quirk to reduce clock rate
for "SDR104" mode on IMX side for Marvell 8887
WiFi + Bluetooth chip side, as Marvell does not recommend
to use SDIO at the speed of higher than 150MHz.

Signed-off-by: Diwakar Sharma <diwakar.sharma@in.bosch.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:39 +02:00
harish_kandiga@mentor.com ebc5a1bf4f mmc: core: Add a new quirk for limiting clock rate
This patch adds a quirk to limit clock rate which
can be used to reduce the SDIO clock rate for some
chips with broken UHS.

Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:39 +02:00
Andrew Gabbasov 207b652cdb mmc: card: Don't show eMMC RPMB and BOOT areas in /proc/partitions
Since RPMB area is accessible via special ioctl only and boot areas
are unlikely to contain any partitions, exclude them all from listing
in /proc/partitions. This will hide them from various user-level
software (e.g. fdisk), thus avoiding unnecessary access attempts.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:36 +02:00
Tobin C. Harding 486e666136 mmc: pwrseq: Use kmalloc_array instead of stack VLA
The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
(kernel Oops) or a security flaw (overwriting memory beyond the
stack). Also, in general, as code evolves it is easy to lose track of
how big a VLA can get. Thus, we can end up having runtime failures
that are hard to debug. As part of the directive[1] to remove all VLAs
from the kernel, and build with -Wvla.

Currently driver is using a VLA declared using the number of descriptors.  This
array is used to store integer values and is later used as an argument to
`gpiod_set_array_value_cansleep()` This can be avoided by using
`kmalloc_array()` to allocate memory for the array of integer values.  Memory is
free'd before return from function.

>From the code it appears that it is safe to sleep so we can use GFP_KERNEL
(based _cansleep() suffix of function `gpiod_set_array_value_cansleep()`.

It can be expected that this patch will result in a small increase in overhead
due to the use of `kmalloc_array()`

[1] https://lkml.org/lkml/2018/3/7/621

Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-02 15:08:29 +02:00
Linus Torvalds d1cb7718cf MMC core:
- Prevent bus reference leak in mmc_blk_init()
 
 MMC host:
  - tmio: Fix error handling when issuing CMD23
  - jz4740: Fix race condition in IRQ mask update
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJazf1FAAoJEP4mhCVzWIwpyu4QALXnHeCXzJZzqE5OvlwLIDWv
 F6CIbP2fbzKgSEZfTrlwZZdVEH3K9DPLn3BosBuMyoupS+BJpB03Cv3fohykQSrt
 rc8YHAsaakHE9T59jibNjq5zJjCe7mWEkMarvzqswXD1xmHGrCCD7JMb/lS2lu57
 0iZ8F1mYDdimbDfZAStuROPPQsFQbY4ugNdKudXfN2NmchB0j2pjZHNvKem2H8nf
 prroq7vfneWSSrW7caOKwUrlqNMMFfrmOCnYSrN1NR38LkLIkPPggbCucpYNwSb/
 oFfgN3u4kFq3mJFUXFqX0b5sYufHEmUwGyBXkK3KIV+rjJY5ctC0jAuyv0rgq4hK
 WuzWAkWhnsqaJgtQiZFroV2xel2dPH34wrdaqr4v65rjF2ZD8Vb9rqIbJTchGlaO
 qylOj9tb2rU0OYu7fXJZGWsMtZlrwPKqvJQCLFMjAV94YKiY3/QgIHeoZs19T/0Y
 F9TLBjNBdLwxAA4n1/5fWUywPwH89riz1TXOpoiV00Q4aGVJXRMHK6dECoe2a2Jx
 ruRRdgaPLiEdTEJhWxVGUcHjjNcu6GH7IkZqdhpjKbn6b3pqY6PDUIxnRfGSwh1g
 ytRKDLs7SmXp7V0dKXxLyXL5sYSmWRKwAldNGpquCRWgX/d2oKvvp1laIAXLZrHb
 mIm+PuE8bOQ9bu4cVE2/
 =pvxh
 -----END PGP SIGNATURE-----

Merge tag 'mmc-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC fixes from Ulf Hansson:
 "MMC core:
   - Prevent bus reference leak in mmc_blk_init()

  MMC host:
   - tmio: Fix error handling when issuing CMD23
   - jz4740: Fix race condition in IRQ mask update"

* tag 'mmc-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: tmio: Fix error handling when issuing CMD23
  mmc: core: Prevent bus reference leak in mmc_blk_init()
  mmc: jz4740: Fix race condition in IRQ mask update
2018-04-12 10:59:03 -07:00
Linus Torvalds 3526dd0c78 for-4.17/block-20180402
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABCAAGBQJawr05AAoJEPfTWPspceCmT2UP/1uuaqwzyl4VjFNb/k7KS7UM
 +Cs/1HBlGomgMA8orDTGqtWqLRdR3z4RSh0+MvXTzQ78HpFVYz7CbDc9itHm+G9M
 X0ypD4kF/JGCFb5cxk+x6qv28uO2nv4DP3+0hHqJWLH4UVJBWDY6bs4BPShsf9QB
 I6XjioNMhoqylXgdOITLODJZz+TcChlJMDAqwhpJwh9TH1wjobleAZ6AdmCPfgi5
 h0UCKMUKzcVJlNZwQUrzrs2cxcx9Uhunnbz7HK0ZV4n/FKFtDpGynFpQQ71pZxKe
 Be0ZOBPCQvC3ykOM/egCIvC/e5y7FgrjORD6jxyu1PTwAugI5E1VYSMxHkXvgPAx
 zOo9A7RT4GPO2tDQv+DbzNFpqeSAclTgSmr+/y1wmheBs8DiSt7MPVBiNM4zdCNv
 NLk9z7IEjFhdmluSB/LbTb1aokypMb/q7QTLouPHdwGn80k7yrhFyLHgdjpNTQ2K
 UHfHZvGxkOX6SmFhBNOtIFUkuSceenh64a0RkRle7filx+ImpbCVm2/GYi9zZNCu
 EtctgzLbLmz40zMiyDaZS2bxBgGzfn6yf4xd9LsaAJPMhvZnmXogT0D9ctWXB0WU
 mMaS7sOkLnNjnGkzF1fHkeiZ/oigrstJbe+CA7BtOdwxpWn6MZBgKEoFQ6iA2b3X
 5J1axMgVH5LAsIEcEQVq
 =RVhK
 -----END PGP SIGNATURE-----

Merge tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block

Pull block layer updates from Jens Axboe:
 "It's a pretty quiet round this time, which is nice. This contains:

   - series from Bart, cleaning up the way we set/test/clear atomic
     queue flags.

   - series from Bart, fixing races between gendisk and queue
     registration and removal.

   - set of bcache fixes and improvements from various folks, by way of
     Michael Lyle.

   - set of lightnvm updates from Matias, most of it being the 1.2 to
     2.0 transition.

   - removal of unused DIO flags from Nikolay.

   - blk-mq/sbitmap memory ordering fixes from Omar.

   - divide-by-zero fix for BFQ from Paolo.

   - minor documentation patches from Randy.

   - timeout fix from Tejun.

   - Alpha "can't write a char atomically" fix from Mikulas.

   - set of NVMe fixes by way of Keith.

   - bsg and bsg-lib improvements from Christoph.

   - a few sed-opal fixes from Jonas.

   - cdrom check-disk-change deadlock fix from Maurizio.

   - various little fixes, comment fixes, etc from various folks"

* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
  blk-mq: Directly schedule q->timeout_work when aborting a request
  blktrace: fix comment in blktrace_api.h
  lightnvm: remove function name in strings
  lightnvm: pblk: remove some unnecessary NULL checks
  lightnvm: pblk: don't recover unwritten lines
  lightnvm: pblk: implement 2.0 support
  lightnvm: pblk: implement get log report chunk
  lightnvm: pblk: rename ppaf* to addrf*
  lightnvm: pblk: check for supported version
  lightnvm: implement get log report chunk helpers
  lightnvm: make address conversions depend on generic device
  lightnvm: add support for 2.0 address format
  lightnvm: normalize geometry nomenclature
  lightnvm: complete geo structure with maxoc*
  lightnvm: add shorten OCSSD version in geo
  lightnvm: add minor version to generic geometry
  lightnvm: simplify geometry structure
  lightnvm: pblk: refactor init/exit sequences
  lightnvm: Avoid validation of default op value
  lightnvm: centralize permission check for lightnvm ioctl
  ...
2018-04-05 14:27:02 -07:00
Alexander Kappner d0a0852b9f mmc: core: Prevent bus reference leak in mmc_blk_init()
Upon module load, mmc_block allocates a bus with bus_registeri() in
mmc_blk_init(). This reference never gets freed during module unload, which
leads to subsequent re-insertions of the module fails and a WARN() splat is
triggered.

Fix the bug by dropping the reference for the bus in mmc_blk_exit().

Signed-off-by: Alexander Kappner <agk@godking.net>
Fixes: 97548575be ("mmc: block: Convert RPMB to a character device")
Cc: <stable@vger.kernel.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-04-04 09:56:23 +02:00
Shawn Lin 57678e5a3d mmc: block: Delete gendisk before cleaning up the request queue
dd if=/dev/urandom of=/dev/mmcblk1 bs=4k count=10000
with a SD card hotplug during transfer reports a warning below
introduced by commit a063057d7c ("block: Fix a race between
request queue removal and the block cgroup controller"). So we
should now remove the disk, partition and bdi sysfs attributes
before cleaning up the request queue associated with the disk.

[  410.331226] mmc1: card 59b4 removed
[  410.348583] WARNING: CPU: 0 PID: 5 at block/blk-core.c:785
blk_cleanup_queue+0x138/0x140
[  410.349294] Modules linked in:
[  410.349570] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted
4.16.0-rc6-next-20180321-00004-gc2ad6a7 #263
[  410.350363] Hardware name: Excavator-RK3399 Board (DT)
[  410.350819] Workqueue: events_freezable mmc_rescan
[  410.351242] pstate: 60000005 (nZCv daif -PAN -UAO)
[  410.351663] pc : blk_cleanup_queue+0x138/0x140
[  410.352054] lr : blk_cleanup_queue+0xac/0x140
[  410.352436] sp : ffff0000092cbb90
[  410.352727] x29: ffff0000092cbb90 x28: 0000000000000000
[  410.353195] x27: ffff8000f6f23030 x26: ffff00000904e610
[  410.353662] x25: ffff8000f17cc808 x24: ffff8000f1038200
[  410.354128] x23: 0000000000000060 x22: 0000000000000000
[  410.354595] x21: ffff8000f11748d8 x20: ffff8000f1038200
[  410.355061] x19: ffff8000f1174200 x18: 0000ffff936347d8
[  410.355528] x17: 0000ffff935b93c0 x16: ffff0000081263f8
[  410.355994] x15: 0000000000000000 x14: 0000000000000400
[  410.356461] x13: 0000000000000001 x12: 0000000000000001
[  410.356927] x11: 0000000000000040 x10: ffff8000f2400028
[  410.357393] x9 : ffff8000f2400040 x8 : 0000000000000000
[  410.357860] x7 : ffff8000f6f3a340 x6 : ffff8000f6f3a340
[  410.358326] x5 : ffff8000f2400000 x4 : ffff8000f6f3a340
[  410.358792] x3 : 0000000000000000 x2 : 39c1333e45670800
[  410.359259] x1 : 0000000000000000 x0 : 0000000000000003
[  410.359726] Call trace:
[  410.359943]  blk_cleanup_queue+0x138/0x140
[  410.360305]  mmc_cleanup_queue+0x2c/0x48
[  410.360652]  mmc_blk_remove_req+0x1c/0x98
[  410.361005]  mmc_blk_remove+0x180/0x1c0
[  410.361343]  mmc_bus_remove+0x1c/0x28
[  410.361670]  device_release_driver_internal+0x154/0x1f0
[  410.362128]  device_release_driver+0x14/0x20
[  410.362504]  bus_remove_device+0xc8/0x108
[  410.362858]  device_del+0x120/0x350
[  410.363167]  mmc_remove_card+0x5c/0xb8
[  410.363498]  mmc_sd_detect+0x40/0x78
[  410.363813]  mmc_rescan+0x19c/0x368
[  410.364123]  process_one_work+0x1ac/0x318
[  410.364477]  worker_thread+0x50/0x450
[  410.364801]  kthread+0xf8/0x128
[  410.365081]  ret_from_fork+0x10/0x18
[  410.365395] ---[ end trace 268e87a46c28968c ]---

Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-03-22 11:04:32 -06:00
Joel Cunningham 8647d26eb3 mmc: update sdio_claim_irq documentation
Update documentation for sdio_claim_irq to downgrade the wording
about doing recursive claims in an IRQ handler from 'must not' to
'should not'. This clarifies that recursive claims are supported,
but not the recommended (best) practice

Signed-off-by: Joel Cunningham <joel.cunningham@garmin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-03-22 10:50:24 +01:00
Abbas Raza 9c5c685e58 mmc: Export host capabilities to debugfs.
This patch exports the host capabilities to debugfs

Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
[Harish: Added caps2, moved creation to mmc_add_host_debugfs]
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-03-22 10:36:27 +01:00
Dirk Behme 8ef0797a89 mmc: core: Disable HPI for certain Micron (Numonyx) eMMC cards
Certain Micron eMMC v4.5 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.

In U-Boot, these cards are reported as

Manufacturer: Micron (ID: 0xFE)
OEM: 0x4E
Name: MMC32G
Revision: 19 (0x13)
Serial: 959241022  Manufact. date: 8/2015 (0x82)  CRC: 0x00
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 29.1 GiB
Boot Partition Size: 16 MiB
Bus Width: 8-bit

According to JEDEC JEP106 manufacturer 0xFE is Numonyx, which was bought by
Micron.

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Cc: <stable@vger.kernel.org> # 4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-03-15 14:43:25 +01:00
Bastian Stender a0e9576634 mmc: block: fix updating ext_csd caches on ioctl call
PARTITION_CONFIG is cached in mmc_card->ext_csd.part_config and the
currently active partition in mmc_blk_data->part_curr. These caches do
not always reflect changes if the ioctl call modifies the
PARTITION_CONFIG registers, e.g. by changing BOOT_PARTITION_ENABLE.

Write the PARTITION_CONFIG value extracted from the ioctl call to the
cache and update the currently active partition accordingly. This
ensures that the user space cannot change the values behind the
kernel's back. The next call to mmc_blk_part_switch() will operate on
the data set by the ioctl and reflect the changes appropriately.

Signed-off-by: Bastian Stender <bst@pengutronix.de>
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-03-15 14:43:24 +01:00
Harish Jenny K N 974e85e90c mmc: core: Export card RCA register via sysfs
This patch exports RCA register to sysfs which will help in reading the
disk identification information.

Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-03-15 14:43:05 +01:00
Markus Elfring 97a0c3134f mmc: core: Use memdup_user() rather than duplicating its implementation
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-03-15 09:37:20 +01:00
Shawn Lin 3715ce57f4 mmc: sd: Remove redundant err assignment from mmc_read_switch
Variable err would be firstly initialized by the return value of
mmc_sd_switch().

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-03-15 09:32:30 +01:00
Shawn Lin 1e178270df mmc: sdio: Check the return value of sdio_enable_4bit_bus
Since we could move card->host->caps & MMC_CAP_4_BIT_DATA
ahead of mmc_sdio_init_uhs_card, in mmc_host_uhs(). So there
we could save this bit to check that. Also, if the process of
sdio_enable_4bit_bus goes wrong, we should bails out early.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-03-15 09:32:30 +01:00
Shawn Lin d6743a8a1a mmc: core: Don't try UHS-I mode if 4-bit mode isn't supported
Per SD specification physical layer v4.0, section 3.9.4, it
says "UHS-I supports only 4-bit mode. Host shall select 4-bit
mode by ACMD6. However mmc_sd_init_uhs_card() still go ahead
to initialize the cards anyway, whether card or host won't
support 4-bit mode.

  This breaks the platforms which could support UHS-I mode but on
some certain boards only support 1-bit mode with a UHS-I card inserted,
as all the tuning process is broken due to this. Alternatively, we
should check the return value from mmc_set_bus_width() to see if host
could finish the request to switch the bus width on its side. But that
needs more thing to do than this patch that just bails out early to try
high speed mode if 4-bit mode isn't available for whatever reason. And
this patch could also fix the same problem for sdio since R4_18V_PRESENT
won't be set for ocr when mmc_sdio_init_card() finds mmc_host_uhs()
is false.

  Note that this patch doesn't keep the checking of card->scr.sda_spec3
and comparing card->scr.bus_widths with SD_SCR_BUS_WIDTH_4 within
mmc_sd_init_uhs_card() since if the sd cards response with SD_ROCR_S18A,
it definitely supports UHS-I mode, which implicitly means these checkings
are always true.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-03-15 09:30:39 +01:00