they're mostly minor cleanups and some debugfs stuff. The real work
that's in here is the typical pile of clk driver updates and new SoC
support. Per usual (or maybe just recent trends), Qualcomm gains a
handful of SoC drivers additions and has the largest diffstat. After
that there are quite a few updates to the Allwinner (sunxi) drivers to
support modular drivers and Renesas is heavily updated to add more
support for various clks. Overall it looks pretty normal.
New Drivers:
- Add MDMA and BDMA clks to Ingenic JZ4760 and JZ4770
- MediaTek mt7986 SoC basic support
- Clock and reset driver for Toshiba Visconti SoCs
- Initial clock driver for the Exynos7885 SoC (Samsung Galaxy A8)
- Allwinner D1 clks
- Lan966x Generic Clock Controller driver and associated DT bindings
- Qualcomm SDX65, SM8450, and MSM8976 GCC clks
- Qualcomm SDX65 and SM8450 RPMh clks
Updates:
- Set suppress_bind_attrs to true for i.MX8ULP driver
- Switch from do_div to div64_ul for throughout all i.MX drivers
- Fix imx8mn_clko1_sels for i.MX8MN
- Remove unused IPG_AUDIO_ROOT from i.MX8MP
- Switch parent for audio_root_clk to audio ahb in i.MX8MP driver
- Removal of all remaining uses of __clk_lookup() in drivers/clk/samsung
- Refactoring of the CPU clocks registration to use common interface
- An update of the Exynos850 driver (support for more clock domains)
required by the E850-96 development board
- Prep for runtime PM and generic power domains on Tegra
- Support modular Allwinner clk drivers via platform bus
- Lan966x clock driver extended to support clock gating
- Add serial (SCI1), watchdog (WDT), timer (OSTM), SPI (RSPI), and
thermal (TSU) clocks and resets on Renesas RZ/G2L
- Rework SDHI clock handling in the Renesas R-Car Gen3 and RZ/G2 clock
drivers, and in the Renesas SDHI driver
- Make the Cortex-A55 (I) clock on Renesas RZ/G2L programmable
- Document support for the new Renesas R-Car S4-8 (R8A779F0) SoC
- Add support for the new Renesas R-Car S4-8 (R8A779F0) SoC
- Add GPU clock and resets on Renesas RZ/G2L
- Add clk-provider.h to various Qualcomm clk drivers
- devm version of clk_hw_register_gate()
- kerneldoc fixes in a couple drivers
-----BEGIN PGP SIGNATURE-----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=jB+l
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have a couple patches in the framework core this time around but
they're mostly minor cleanups and some debugfs stuff. The real work
that's in here is the typical pile of clk driver updates and new SoC
support.
Per usual (or maybe just recent trends), Qualcomm gains a handful of
SoC drivers additions and has the largest diffstat. After that there
are quite a few updates to the Allwinner (sunxi) drivers to support
modular drivers and Renesas is heavily updated to add more support for
various clks.
Overall it looks pretty normal.
New Drivers:
- Add MDMA and BDMA clks to Ingenic JZ4760 and JZ4770
- MediaTek mt7986 SoC basic support
- Clock and reset driver for Toshiba Visconti SoCs
- Initial clock driver for the Exynos7885 SoC (Samsung Galaxy A8)
- Allwinner D1 clks
- Lan966x Generic Clock Controller driver and associated DT bindings
- Qualcomm SDX65, SM8450, and MSM8976 GCC clks
- Qualcomm SDX65 and SM8450 RPMh clks
Updates:
- Set suppress_bind_attrs to true for i.MX8ULP driver
- Switch from do_div to div64_ul for throughout all i.MX drivers
- Fix imx8mn_clko1_sels for i.MX8MN
- Remove unused IPG_AUDIO_ROOT from i.MX8MP
- Switch parent for audio_root_clk to audio ahb in i.MX8MP driver
- Removal of all remaining uses of __clk_lookup() in
drivers/clk/samsung
- Refactoring of the CPU clocks registration to use common interface
- An update of the Exynos850 driver (support for more clock domains)
required by the E850-96 development board
- Prep for runtime PM and generic power domains on Tegra
- Support modular Allwinner clk drivers via platform bus
- Lan966x clock driver extended to support clock gating
- Add serial (SCI1), watchdog (WDT), timer (OSTM), SPI (RSPI), and
thermal (TSU) clocks and resets on Renesas RZ/G2L
- Rework SDHI clock handling in the Renesas R-Car Gen3 and RZ/G2
clock drivers, and in the Renesas SDHI driver
- Make the Cortex-A55 (I) clock on Renesas RZ/G2L programmable
- Document support for the new Renesas R-Car S4-8 (R8A779F0) SoC
- Add support for the new Renesas R-Car S4-8 (R8A779F0) SoC
- Add GPU clock and resets on Renesas RZ/G2L
- Add clk-provider.h to various Qualcomm clk drivers
- devm version of clk_hw_register_gate()
- kerneldoc fixes in a couple drivers"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (131 commits)
clk: visconti: Remove pointless NULL check in visconti_pll_add_lookup()
clk: mediatek: add mt7986 clock support
clk: mediatek: add mt7986 clock IDs
dt-bindings: clock: mediatek: document clk bindings for mediatek mt7986 SoC
clk: mediatek: clk-gate: Use regmap_{set/clear}_bits helpers
clk: mediatek: clk-gate: Shrink by adding clockgating bit check helper
clk: x86: Fix clk_gate_flags for RV_CLK_GATE
clk: x86: Use dynamic con_id string during clk registration
ACPI: APD: Add a fmw property clk-name
drivers: acpi: acpi_apd: Remove unused device property "is-rv"
x86: clk: clk-fch: Add support for newer family of AMD's SOC
clk: ingenic: Add MDMA and BDMA clocks
dt-bindings: clk/ingenic: Add MDMA and BDMA clocks
clk: bm1880: remove kfrees on static allocations
clk: Drop unused COMMON_CLK_STM32MP157_SCMI config
clk: st: clkgen-mux: search reg within node or parent
clk: st: clkgen-fsyn: search reg within node or parent
clk: Enable/Disable runtime PM for clk_summary
MAINTAINERS: Add entries for Toshiba Visconti PLL and clock controller
clk: visconti: Add support common clock driver and reset driver
...
The registers for some clocks in the SOC area, which are under the power
domain are required to be enabled before accessing them. During the
clk_summary if the power-domains are not enabled they could result into
NoC errors.
Thus ensure the register access of the clock controller is done with
pm_untime_get/put functions.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1640018638-19436-3-git-send-email-tdas@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We don't want vendors to be enabling this part of the clk code and
shipping it to customers. Exposing the ability to change clk frequencies
and parents via debugfs is potentially damaging to the system if folks
don't know what they're doing. Emit a strong warning so that the message
is clear: don't enable this outside of development systems.
Fixes: 37215da555 ("clk: Add support for setting clk_rate via debugfs")
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211210014237.2130300-1-sboyd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Useful for testing mux clocks. One can write the index of the parent to
be set into clk_parent node, starting from 0. Example
# cd /sys/kernel/debug/clk/mout_peri_bus
# cat clk_possible_parents
dout_shared0_div4 dout_shared1_div4
# cat clk_parent
dout_shared0_div4
# echo 1 > clk_parent
# cat clk_parent
dout_shared1_div4
CLOCK_ALLOW_WRITE_DEBUGFS has to be defined in drivers/clk/clk.c in
order to use this feature.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Link: https://lore.kernel.org/r/20211013172042.10884-1-semen.protsenko@linaro.org
[sboyd@kernel.org: Collapse ifdefs]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Nothing stops a clk controller from registering an OF clk provider
before registering those clks with the clk framework. This is not great
but we deal with it in the clk framework by refusing to hand out struct
clk pointers when 'hw->core' is NULL, the indication that clk_register()
has been called.
Within clk_core_fill_parent_index() we considered this case when a
clk_hw pointer is referenced directly by filling in the parent cache
with an -EPROBE_DEFER pointer when the core pointer is NULL. When we
lookup a parent with clk_core_get() we don't care about the return value
being NULL though, because that was considered largely impossible, but
it's been proven now that it can be NULL if two clk providers are
probing in parallel and the parent provider has been registered before
the clk has. Let's check for NULL here as well and treat it the same as
direct clk_hw references.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20211208041534.3928718-1-sboyd@kernel.org
Before commit fc0c209c14 ("clk: Allow parents to be specified without
string names") child clks couldn't find their parent until the parent
clk was added to a list in __clk_core_init(). After that commit, child
clks can reference their parent clks directly via a clk_hw pointer, or
they can lookup that clk_hw pointer via DT if the parent clk is
registered with an OF clk provider.
The common clk framework treats hw->core being non-NULL as "the clk is
registered" per the logic within clk_core_fill_parent_index():
parent = entry->hw->core;
/*
* We have a direct reference but it isn't registered yet?
* Orphan it and let clk_reparent() update the orphan status
* when the parent is registered.
*/
if (!parent)
Therefore we need to be extra careful to not set hw->core until the clk
is fully registered with the clk framework. Otherwise we can get into a
situation where a child finds a parent clk and we move the child clk off
the orphan list when the parent isn't actually registered, wrecking our
enable accounting and breaking critical clks.
Consider the following scenario:
CPU0 CPU1
---- ----
struct clk_hw clkBad;
struct clk_hw clkA;
clkA.init.parent_hws = { &clkBad };
clk_hw_register(&clkA) clk_hw_register(&clkBad)
... __clk_register()
hw->core = core
...
__clk_register()
__clk_core_init()
clk_prepare_lock()
__clk_init_parent()
clk_core_get_parent_by_index()
clk_core_fill_parent_index()
if (entry->hw) {
parent = entry->hw->core;
At this point, 'parent' points to clkBad even though clkBad hasn't been
fully registered yet. Ouch! A similar problem can happen if a clk
controller registers orphan clks that are referenced in the DT node of
another clk controller.
Let's fix all this by only setting the hw->core pointer underneath the
clk prepare lock in __clk_core_init(). This way we know that
clk_core_fill_parent_index() can't see hw->core be non-NULL until the
clk is fully registered.
Fixes: fc0c209c14 ("clk: Allow parents to be specified without string names")
Signed-off-by: Mike Tipton <quic_mdtipton@quicinc.com>
Link: https://lore.kernel.org/r/20211109043438.4639-1-quic_mdtipton@quicinc.com
[sboyd@kernel.org: Reword commit text, update comment]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In case clock flags contains CLK_GET_RATE_NOCACHE the clk_rate_get()
will return the cached rate. Thus, use clk_core_get_rate_recalc() which
takes proper action when clock flags contains CLK_GET_RATE_NOCACHE.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20211011112719.3951784-16-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[sboyd@kernel.org: Grab prepare lock around operation]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
commit 6579c8d97a ("clk: Mark fwnodes when their clock provider is added")
revealed that clk/bcm/clk-raspberrypi.c driver calls
devm_of_clk_add_hw_provider(), with a NULL dev->of_node, which resulted in a
NULL pointer dereference in of_clk_add_hw_provider() when calling
fwnode_dev_initialized().
Returning 0 is reducing the if conditions in driver code and is being
consistent with the CONFIG_OF=n inline stub that returns 0 when CONFIG_OF
is disabled. The downside is that drivers will maybe register clkdev lookups
when they don't need to and waste some memory.
Fixes: 6579c8d97a ("clk: Mark fwnodes when their clock provider is added")
Fixes: 3c9ea42802 ("clk: Mark fwnodes when their clock provider is added/removed")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210426065618.588144-1-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usual suspects are here: i.MX, Qualcomm, Renesas, Allwinner, Samsung, and
Rockchip, but it feels pretty light on commits. There's only one real commit to
the framework core and that's to consolidate code. Otherwise the diffstat is
dominated by many Qualcomm clk driver patches that modernize the driver for the
proper way of speciying clk parents. That's shifting data around, which could
subtly break things so I'll be on the lookout for fixes.
New Drivers:
- Proper clk driver for Mediatek MT7621 SoCs
- Support for the clock controller on the new Rockchip rk3568
Updates:
- Simplify Zynq Kconfig dependencies
- Use clk_hw pointers in socfpga driver
- Cleanup parent data in qcom clk drivers
- Some cleanups for rk3399 modularization
- Fix reparenting of i.MX UART clocks by initializing only the ones
associated to stdout
- Correct the PCIE clocks for i.MX8MP and i.MX8MQ
- Make i.MX LPCG and SCU clocks return on registering failure
- Kernel doc fixes
- Add DAB hardware accelerator clocks on Renesas R-Car E3 and M3-N
- Add timer (TMU) clocks on Renesas R-Car H3 ES1.0
- Add Timer (TMU & CMT) and thermal sensor (TSC) clocks on Renesas R-Car V3U
- Sigma-delta modulation on Allwinner V3s audio PLL
-----BEGIN PGP SIGNATURE-----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=z+1G
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Here's a collection of largely clk driver updates. The usual suspects
are here: i.MX, Qualcomm, Renesas, Allwinner, Samsung, and Rockchip,
but it feels pretty light on commits.
There's only one real commit to the framework core and that's to
consolidate code. Otherwise the diffstat is dominated by many Qualcomm
clk driver patches that modernize the driver for the proper way of
speciying clk parents. That's shifting data around, which could subtly
break things so I'll be on the lookout for fixes.
New Drivers:
- Proper clk driver for Mediatek MT7621 SoCs
- Support for the clock controller on the new Rockchip rk3568
Updates:
- Simplify Zynq Kconfig dependencies
- Use clk_hw pointers in socfpga driver
- Cleanup parent data in qcom clk drivers
- Some cleanups for rk3399 modularization
- Fix reparenting of i.MX UART clocks by initializing only the ones
associated to stdout
- Correct the PCIE clocks for i.MX8MP and i.MX8MQ
- Make i.MX LPCG and SCU clocks return on registering failure
- Kernel doc fixes
- Add DAB hardware accelerator clocks on Renesas R-Car E3 and M3-N
- Add timer (TMU) clocks on Renesas R-Car H3 ES1.0
- Add Timer (TMU & CMT) and thermal sensor (TSC) clocks on
Renesas R-Car V3U
- Sigma-delta modulation on Allwinner V3s audio PLL"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (82 commits)
MAINTAINERS: add MT7621 CLOCK maintainer
staging: mt7621-dts: use valid vendor 'mediatek' instead of invalid 'mtk'
staging: mt7621-dts: make use of new 'mt7621-clk'
clk: ralink: add clock driver for mt7621 SoC
clk: uniphier: Fix potential infinite loop
clk: qcom: rpmh: add support for SDX55 rpmh IPA clock
clk: qcom: gcc-sdm845: get rid of the test clock
clk: qcom: convert SDM845 Global Clock Controller to parent_data
dt-bindings: clock: separate SDM845 GCC clock bindings
clk: qcom: apss-ipq-pll: Add missing MODULE_DEVICE_TABLE
clk: qcom: a53-pll: Add missing MODULE_DEVICE_TABLE
clk: qcom: a7-pll: Add missing MODULE_DEVICE_TABLE
dt: bindings: add mt7621-sysc device tree binding documentation
dt-bindings: clock: add dt binding header for mt7621 clocks
clk: samsung: Remove redundant dev_err calls
clk: zynqmp: pll: add set_pll_mode to check condition in zynqmp_pll_enable
clk: zynqmp: move zynqmp_pll_set_mode out of round_rate callback
clk: zynqmp: Drop dependency on ARCH_ZYNQMP
clk: zynqmp: Enable the driver if ZYNQMP_FIRMWARE is selected
clk: qcom: gcc-sm8350: use ARRAY_SIZE instead of specifying num_parents
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmBzdS0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGDdAIAIpKH/tAHhH7s7QH
m5ewgE8foP7M5Ue9fp3+JmbtaYSzhCAMcKhqGtat/zk5PvA9AoYCDXrTetfYtBHh
LUOmhL9hcKItNobfkYBok6BiFjGUEL3HMqz5w+MUsMwnXIc4RXqfJmsQ932z9Kxf
yDwe6ehIzJVrQLI/C0mTamYRHu2aiZ1VWzhKuT493rLeg0R2odCCIClPN+/QvCwb
8/sk6l1c8eOUYYMUzKFZifaZGb12qDjRt4pZmk51aMTzg0WCpElJG+7Uqr4QQhZP
p6xeNuUQq6WwxtlDkmo79Uzkrurb5tN2/hZ1RcJhs3EdHfpR0MjIyH3Znnb31gnu
39VjHhg=
=4KP/
-----END PGP SIGNATURE-----
Merge tag 'v5.12-rc7' into driver-core-next
We need the driver core fix in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix invalid usage of a list_for_each_entry cursor in
clk_notifier_unregister(). When list is empty or if the list
is completely traversed (without breaking from the loop on one
of the entries) then the list cursor does not point to a valid
entry and therefore should not be used. The patch fixes a logical
bug that hasn't been seen in pratice however it is analogus
to the bug fixed in clk_notifier_register().
The issue was dicovered when running 5.12-rc1 kernel on x86_64
with KASAN enabled:
BUG: KASAN: global-out-of-bounds in clk_notifier_register+0xab/0x230
Read of size 8 at addr ffffffffa0d10588 by task swapper/0/1
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.12.0-rc1 #1
Hardware name: Google Caroline/Caroline,
BIOS Google_Caroline.7820.430.0 07/20/2018
Call Trace:
dump_stack+0xee/0x15c
print_address_description+0x1e/0x2dc
kasan_report+0x188/0x1ce
? clk_notifier_register+0xab/0x230
? clk_prepare_lock+0x15/0x7b
? clk_notifier_register+0xab/0x230
clk_notifier_register+0xab/0x230
dw8250_probe+0xc01/0x10d4
...
Memory state around the buggy address:
ffffffffa0d10480: 00 00 00 00 00 03 f9 f9 f9 f9 f9 f9 00 00 00 00
ffffffffa0d10500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f9 f9
>ffffffffa0d10580: f9 f9 f9 f9 00 00 00 00 00 00 00 00 00 00 00 00
^
ffffffffa0d10600: 00 00 00 00 00 00 f9 f9 f9 f9 f9 f9 00 00 00 00
ffffffffa0d10680: 00 00 00 00 00 00 00 00 f9 f9 f9 f9 00 00 00 00
==================================================================
Fixes: b2476490ef ("clk: introduce the common clock framework")
Reported-by: Lukasz Majczak <lma@semihalf.com>
Signed-off-by: Lukasz Bartosik <lb@semihalf.com>
Link: https://lore.kernel.org/r/20210401225149.18826-2-lb@semihalf.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fix invalid usage of a list_for_each_entry cursor in
clk_notifier_register(). When list is empty or if the list
is completely traversed (without breaking from the loop on one
of the entries) then the list cursor does not point to a valid
entry and therefore should not be used.
The issue was dicovered when running 5.12-rc1 kernel on x86_64
with KASAN enabled:
BUG: KASAN: global-out-of-bounds in clk_notifier_register+0xab/0x230
Read of size 8 at addr ffffffffa0d10588 by task swapper/0/1
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.12.0-rc1 #1
Hardware name: Google Caroline/Caroline,
BIOS Google_Caroline.7820.430.0 07/20/2018
Call Trace:
dump_stack+0xee/0x15c
print_address_description+0x1e/0x2dc
kasan_report+0x188/0x1ce
? clk_notifier_register+0xab/0x230
? clk_prepare_lock+0x15/0x7b
? clk_notifier_register+0xab/0x230
clk_notifier_register+0xab/0x230
dw8250_probe+0xc01/0x10d4
...
Memory state around the buggy address:
ffffffffa0d10480: 00 00 00 00 00 03 f9 f9 f9 f9 f9 f9 00 00 00 00
ffffffffa0d10500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f9 f9
>ffffffffa0d10580: f9 f9 f9 f9 00 00 00 00 00 00 00 00 00 00 00 00
^
ffffffffa0d10600: 00 00 00 00 00 00 f9 f9 f9 f9 f9 f9 00 00 00 00
ffffffffa0d10680: 00 00 00 00 00 00 00 00 f9 f9 f9 f9 00 00 00 00
==================================================================
Fixes: b2476490ef ("clk: introduce the common clock framework")
Reported-by: Lukasz Majczak <lma@semihalf.com>
Signed-off-by: Lukasz Bartosik <lb@semihalf.com>
Link: https://lore.kernel.org/r/20210401225149.18826-1-lb@semihalf.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The comments for clk_core_determine_round_nolock() contain a double
"if": one at the end of a line, followed by another one at the beginning
of the next line. Drop the former.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210326120833.1578153-1-geert+renesas@glider.be
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This is a follow-up for:
commit 3c9ea42802 ("clk: Mark fwnodes when their clock provider is added/removed")
The above commit updated the deprecated of_clk_add_provider(),
but missed to update the preferred of_clk_add_hw_provider().
Update it now.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210210114435.122242-2-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the "big" driver core and debugfs update for 5.12-rc1
This set of driver core patches caused a bunch of problems in linux-next
for the past few weeks, when Saravana tried to set fw_devlink=on as the
default functionality. This caused a number of systems to stop booting,
and lots of bugs were fixed in this area for almost all of the reported
systems, but this option is not ready to be turned on just yet for the
default operation based on this testing, so I've reverted that change at
the very end so we don't have to worry about regressions in 5.12. We
will try to turn this on for 5.13 if testing goes better over the next
few months.
Other than the fixes caused by the fw_devlink testing in here, there's
not much more:
- debugfs fixes for invalid input into debugfs_lookup()
- kerneldoc cleanups
- warn message if platform drivers return an error on their
remove callback (a futile effort, but good to catch).
All of these have been in linux-next for a while now, and the
regressions have gone away with the revert of the fw_devlink change.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYDZhzA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylS2wCfU28FxDWNwcWhPFVfRT8Mb3OxZ50An1sR4lNR
t5Ie4aztMUjVJhI9bq6g
=3NSB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core / debugfs update from Greg KH:
"Here is the "big" driver core and debugfs update for 5.12-rc1
This set of driver core patches caused a bunch of problems in
linux-next for the past few weeks, when Saravana tried to set
fw_devlink=on as the default functionality. This caused a number of
systems to stop booting, and lots of bugs were fixed in this area for
almost all of the reported systems, but this option is not ready to be
turned on just yet for the default operation based on this testing, so
I've reverted that change at the very end so we don't have to worry
about regressions in 5.12
We will try to turn this on for 5.13 if testing goes better over the
next few months.
Other than the fixes caused by the fw_devlink testing in here, there's
not much more:
- debugfs fixes for invalid input into debugfs_lookup()
- kerneldoc cleanups
- warn message if platform drivers return an error on their remove
callback (a futile effort, but good to catch).
All of these have been in linux-next for a while now, and the
regressions have gone away with the revert of the fw_devlink change"
* tag 'driver-core-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (35 commits)
Revert "driver core: Set fw_devlink=on by default"
of: property: fw_devlink: Ignore interrupts property for some configs
debugfs: do not attempt to create a new file before the filesystem is initalized
debugfs: be more robust at handling improper input in debugfs_lookup()
driver core: auxiliary bus: Fix calling stage for auxiliary bus init
of: irq: Fix the return value for of_irq_parse_one() stub
of: irq: make a stub for of_irq_parse_one()
clk: Mark fwnodes when their clock provider is added/removed
PM: domains: Mark fwnodes when their powerdomain is added/removed
irqdomain: Mark fwnodes when their irqdomain is added/removed
driver core: fw_devlink: Handle suppliers that don't use driver core
of: property: Add fw_devlink support for optional properties
driver core: Add fw_devlink.strict kernel param
of: property: Don't add links to absent suppliers
driver core: fw_devlink: Detect supplier devices that will never be added
driver core: platform: Emit a warning if a remove callback returned non-zero
of: property: Fix fw_devlink handling of interrupts/interrupts-extended
gpiolib: Don't probe gpio_device if it's not the primary device
device.h: Remove bogus "the" in kerneldoc
gpiolib: Bind gpio_device to a driver to enable fw_devlink=on by default
...
This allows fw_devlink to recognize clock provider drivers that don't
use the device-driver model to initialize the device. fw_devlink will
use this information to make sure consumers of such clock providers
aren't indefinitely blocked from probing, waiting for the power domain
device to appear and bind to a driver.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210205222644.2357303-9-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clock API splits its interface into sleepable ant atomic contexts:
- clk_prepare/clk_unprepare for stuff that might sleep
- clk_enable_clk_disable for anything that may be done in atomic context
The code handling runtime PM for clocks only calls clk_disable() on
suspend requests, and clk_enable on resume requests. This means that
runtime PM with clock providers that only have the prepare/unprepare
methods implemented is basically useless.
Many clock implementations can't accommodate atomic contexts. This is
often the case when communication with the clock happens through another
subsystem like I2C or SCMI.
Let's make the clock PM code useful with such clocks by safely invoking
clk_prepare/clk_unprepare upon resume/suspend requests. Of course, when
such clocks are registered with the PM layer then pm_runtime_irq_safe()
can't be used, and neither pm_runtime_suspend() nor pm_runtime_resume()
may be invoked in atomic context.
For clocks that do implement the enable and disable methods then
everything just works as before.
A note on sparse:
According to https://lwn.net/Articles/109066/ there are things
that sparse can't cope with. In particular, pm_clk_op_lock() and
pm_clk_op_unlock() may or may not lock/unlock psd->lock depending on
some runtime condition. To work around that we tell it the lock is
always untaken for the purpose of static analisys.
Thanks to Naresh Kamboju for reporting issues with the initial patch.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Add some trace points for clk_set_rate() "range" functions
- DVFS support for AT91 clk driver
* clk-ti:
clk: ti: omap5: Fix reboot DPLL lock failure when using ABE TIMERs
clk: ti: Fix memleak in ti_fapll_synth_setup
* clk-analog:
clk: axi-clkgen: move the OF table at the bottom of the file
clk: axi-clkgen: wrap limits in a struct and keep copy on the state object
dt-bindings: clock: adi,axi-clkgen: convert old binding to yaml format
* clk-trace:
clk: Trace clk_set_rate() "range" functions
* clk-at91:
clk: at91: sam9x60: remove atmel,osc-bypass support
clk: at91: sama7g5: register cpu clock
clk: at91: clk-master: re-factor master clock
clk: at91: sama7g5: do not allow cpu pll to go higher than 1GHz
clk: at91: sama7g5: decrease lower limit for MCK0 rate
clk: at91: sama7g5: remove mck0 from parent list of other clocks
clk: at91: clk-sam9x60-pll: allow runtime changes for pll
clk: at91: sama7g5: add 5th divisor for mck0 layout and characteristics
clk: at91: clk-master: add 5th divisor for mck master
clk: at91: sama7g5: allow SYS and CPU PLLs to be exported and referenced in DT
dt-bindings: clock: at91: add sama7g5 pll defines
clk: at91: sama7g5: fix compilation error
* clk-silabs:
clk: si5351: Wait for bit clear after PLL reset
- Support for SiFive FU740 PRCI
- Add hardware enable information to clk_summary debugfs
* clk-tegra:
clk: tegra: Fix duplicated SE clock entry
clk: tegra: bpmp: Clamp clock rates on requests
clk: tegra: Do not return 0 on failure
* clk-imx: (24 commits)
clk: imx: scu: remove the calling of device_is_bound
clk: imx: scu: Make pd_np with static keyword
clk: imx8mq: drop of_match_ptr from of_device_id table
clk: imx8mp: drop of_match_ptr from of_device_id table
clk: imx8mn: drop of_match_ptr from of_device_id table
clk: imx8mm: drop of_match_ptr from of_device_id table
clk: imx: gate2: Remove unused variable ret
clk: imx: gate2: Add locking in is_enabled op
clk: imx: gate2: Add cgr_mask for more flexible number of control bits
clk: imx: gate2: Check if clock is enabled against cgr_val
clk: imx: gate2: Keep the register writing in on place
clk: imx: gate2: Remove the IMX_CLK_GATE2_SINGLE_BIT special case
clk: imx: scu: fix build break when compiled as modules
clk: imx: remove redundant assignment to pointer np
clk: imx: remove unneeded semicolon
clk: imx: lpcg: add suspend/resume support
clk: imx: clk-imx8qxp-lpcg: add runtime pm support
clk: imx: lpcg: allow lpcg clk to take device pointer
clk: imx: imx8qxp-lpcg: add parsing clocks from device tree
clk: imx: scu: add suspend/resume support
...
* clk-sifive:
clk: sifive: Add clock enable and disable ops
clk: sifive: Fix the wrong bit field shift
clk: sifive: Add a driver for the SiFive FU740 PRCI IP block
clk: sifive: Use common name for prci configuration
clk: sifive: Extract prci core to common base
dt-bindings: fu740: prci: add YAML documentation for the FU740 PRCI
* clk-mediatek:
clk: mediatek: Make mtk_clk_register_mux() a static function
* clk-summary:
clk: Add hardware-enable column to clk summary
The clk_set_rate "range" functions don't have any tracepoints even
though it might be useful. Add some.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201207105050.2096917-1-maxime@cerno.tech
[sboyd@kernel.org: Reword commit text]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add "hardware enable" column to the clk summary in order to show actual
hardware enable-state of all clocks. The possible states are "Y/N/?",
where question mark means that state is unknown, i.e. clock isn't a
mux and clk-driver doesn't support is_enabled() callback for this clock.
In conjunction with clk_ignore_unused, this tells us what unused clocks
are left enabled after bootloader. This is also a useful aid for
debugging interactions with firmware which changes clock states without
notifying kernel.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201115203432.13934-1-digetx@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a memory managed variant of clk_notifier_register() to make life easier
on clock consumers using notifiers
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201021163847.595189-2-jbrunet@baylibre.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk_register() is deprecated. Using 'clk' member of struct clk_hw is
discouraged. With this constraint, it is difficult for driver to
register clocks using the clk_hw API and then use the clock with
the consumer API
This adds a simple helper, clk_hw_get_clk(), to get a struct clk from
a struct clk_hw. Like other clk_get() variant, each call to this helper
must be balanced with a call to clk_put(). To make life easier on the
consumers, a memory managed version is provided as well.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201021162147.563655-3-jbrunet@baylibre.com
Tested-by: Kevin Hilman <khilman@baylibre.com>
[sboyd@kernel.org: Fix kernel-doc]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In clk-devres.c, devm_clk_release() is used to call clk_put() memory
managed clock. In clk.c the same name, in a different scope is used to call
clk_unregister().
As it stands, it is not really a problem but it does not readability,
especially if we need to call clk_put() on managed clock in clk.c
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201021162147.563655-2-jbrunet@baylibre.com
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
make clang-analyzer on x86_64 defconfig caught my attention with:
drivers/clk/clk.c:423:19:
warning: Value stored to 'parent' during its initialization is never read
[clang-analyzer-deadcode.DeadStores]
struct clk_core *parent = ERR_PTR(-ENOENT);
^
Commit fc0c209c14 ("clk: Allow parents to be specified without string
names") introduced clk_core_fill_parent_index() with this unneeded
dead-store initialization.
So, simply remove this unneeded dead-store initialization to make
clang-analyzer happy.
As compilers will detect this unneeded assignment and optimize this anyway,
the resulting object code is identical before and after this change.
No functional change. No change to object code.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20201106094820.30167-1-lukas.bulwahn@gmail.com
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Conversion done using the script at:
https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Add support for SAMA7G5 SoC clks
- Microchip Sparx5 DPLL clk
* clk-microchip:
clk: sparx5: Add Sparx5 SoC DPLL clock driver
dt-bindings: clock: sparx5: Add bindings include file
* clk-mmp:
clk: mmp: avoid missing prototype warning
* clk-unused:
clk: drop unused function __clk_get_flags
* clk-at91:
clk: at91: sama7g5: add clock support for sama7g5
clk: at91: clk-utmi: add utmi support for sama7g5
clk: at91: clk-sam9x60-pll: re-factor to support plls with multiple outputs
clk: at91: add macro for pll ids mask
clk: at91: clk-programmable: add mux_table option
clk: at91: clk-peripheral: add support for changeable parent rate
clk: at91: clk-master: add master clock support for SAMA7G5
clk: at91: clk-generated: add mux_table option
clk: at91: clk-generated: pass the id of changeable parent at registration
clk: at91: replace conditional operator with double logical not
clk: at91: sckc: register slow_rc with accuracy option
clk: at91: sam9x60: fix main rc oscillator frequency
clk: at91: sam9x60-pll: use frac when setting frequency
clk: at91: sam9x60-pll: check fcore against ranges
clk: at91: sam9x60-pll: use logical or for range check
clk: at91: clk-sam9x60-pll: fix mul mask
clk: at91: clk-generated: check best_rate against ranges
clk: at91: clk-generated: continue if __clk_determine_rate() returns error
clk: at91: fix possible dead lock in new drivers
The function __clk_get_flags has not been used since the April 2019
commit a348f05361 ("ARM: omap2+: hwmod: drop CLK_IS_BASIC
flag usage"). Other uses were removed in June 2015, eg by
commit 98d8a60ecc ("clk: Convert __clk_get_flags() to
clk_hw_get_flags()"), which shows how clk_hw_get_flags can easily
be used instead.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1596272022-14173-1-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For test and debug purposes, it's simple enough to enable or disable
clocks from shell. Add a new debugfs file 'clk_prepare_enable' that
calls clk_prepare_enable() when writing "1" and clk_disable_unprepare()
when writing "0".
This can have security implications, so only support it when the code
has been modified to #define CLOCK_ALLOW_WRITE_DEBUGFS.
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20200630003024.6282-1-mdtipton@codeaurora.org
[sboyd@kernel.org: Reword commit text and remove comment update]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
function that isn't used anymore. Otherwise the main new thing for the common
clk framework is that it is selectable in the Kconfig language now. Hopefully
this will let clk drivers and clk consumers be testable on more than the
architectures that support the clk framework. The goal is to introduce some
Kunit tests for the framework.
Outside of the core framework we have the usual set of various driver updates
and non-critical fixes. The dirstat shows that the new Baikal-T1 driver is the
largest addition this time around in terms of lines of code. After that the x86
(Intel), Qualcomm, and Mediatek drivers introduce many lines to support new or
upcoming SoCs. After that the dirstat shows the usual suspects working on their
SoC support by fixing minor bugs, correcting data and converting some of their
DT bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix clock support
on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and clk-pllv3
drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support aarch32 mode on
aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using composite
clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102 defined
bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+
-----BEGIN PGP SIGNATURE-----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=nuG5
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time around we have four lines of diff in the core framework,
removing a function that isn't used anymore. Otherwise the main new
thing for the common clk framework is that it is selectable in the
Kconfig language now. Hopefully this will let clk drivers and clk
consumers be testable on more than the architectures that support the
clk framework. The goal is to introduce some Kunit tests for the
framework.
Outside of the core framework we have the usual set of various driver
updates and non-critical fixes. The dirstat shows that the new
Baikal-T1 driver is the largest addition this time around in terms of
lines of code. After that the x86 (Intel), Qualcomm, and Mediatek
drivers introduce many lines to support new or upcoming SoCs. After
that the dirstat shows the usual suspects working on their SoC support
by fixing minor bugs, correcting data and converting some of their DT
bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix
clock support on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and
clk-pllv3 drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support
aarch32 mode on aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using
composite clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102
defined bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on
Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (155 commits)
clk: mediatek: Remove ifr{0,1}_cfg_regs structures
clk: baikal-t1: remove redundant assignment to variable 'divider'
clk: baikal-t1: fix spelling mistake "Uncompatible" -> "Incompatible"
dt-bindings: clock: Add a missing include to MMP Audio Clock binding
dt: Add bindings for IDT VersaClock 5P49V5925
clk: vc5: Add support for IDT VersaClock 5P49V6965
clk: Add Baikal-T1 CCU Dividers driver
clk: Add Baikal-T1 CCU PLLs driver
dt-bindings: clk: Add Baikal-T1 CCU Dividers binding
dt-bindings: clk: Add Baikal-T1 CCU PLLs binding
clk: mediatek: assign the initial value to clk_init_data of mtk_mux
clk: mediatek: Add MT6765 clock support
clk: mediatek: add mt6765 clock IDs
dt-bindings: clock: mediatek: document clk bindings vcodecsys for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings mipi0a for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings for Mediatek MT6765 SoC
CLK: HSDK: CGU: add support for 148.5MHz clock
CLK: HSDK: CGU: support PLL bypassing
CLK: HSDK: CGU: check if PLL is bypassed first
clk: clk-si5341: Add support for the Si5345 series
...
clk_pm_runtime_get() assumes that the PM-runtime usage counter will
be dropped by pm_runtime_get_sync() on errors, which is not the case,
so PM-runtime references to devices acquired by the former are leaked
on errors returned by the latter.
Fix this by modifying clk_pm_runtime_get() to drop the reference if
pm_runtime_get_sync() returns an error.
Fixes: 9a34b45397 clk: Add support for runtime PM
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
On failing to prepare or enable a clock, remove the core structure
from the list it has been inserted as it is about to be freed.
This otherwise leads to random crashes when subsequent clocks get
registered, during which parsing of the clock tree becomes adventurous.
Observed with QEMU's RPi-3 emulation.
Fixes: 12ead77432 ("clk: Don't try to enable critical clocks if prepare failed")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Link: https://lkml.kernel.org/r/20200505140953.409430-1-maz@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
majority of the diff is the normal collection of driver additions for new SoCs
and non-critical clk data fixes and updates. The framework must be middle aged.
The two biggest directories in the diffstat show that the Qualcomm and Unisoc
support added a handful of big drivers for new SoCs but that's not really the
whole story because those new drivers tend to add large numbers of lines of clk
data. There's a handful of AT91 clk drivers added this time around too and a
bunch of improvements to drivers like the i.MX driver. All around lots of
updates and fixes in various clk drivers which is good to see.
The core framework has only one real major change which has been baking in next
for the past couple months. It fixes the framework so that it stops caching a
clk's phase when the phase clk_op returns an error. Before this change we would
consider some negative errno as a phase and that just doesn't make sense.
Core:
- Don't show clk phase when it is invalid
New Drivers:
- Add support for Unisoc SC9863A clks
- Qualcomm SM8250 RPMh and MSM8976 RPM clks
- Qualcomm SM8250 Global Clock Controller (GCC) support
- Qualcomm SC7180 Modem Clock Controller (MSS CC) support
- EHRPWM's TimeBase clock(TBCLK) for TI AM654 SoCs
- Support PMC clks on at91sam9n12, at91rm9200, sama5d3, and at91sam9g45 SoCs
Updates:
- GPU GX GDSC support on Qualcomm sc7180
- Fixes and improvements for the Marvell MMP2/MMP3 SoC clk drivers
- A series from Anson to convert i.MX8 clock bindings to json-schema
- Update i.MX pll14xx driver to include new frequency entries for pll1443x table,
and return error for invalid PLL type
- Add missing of_node_put() call for a number of i.MX clock drivers
- Drop flag CLK_IS_CRITICAL from 'A53_CORE' mux clock, as we already
have the flag on its child cpu clock
- Fix a53 cpu clock for i.MX8 drivers to get it source from ARM PLL
via CORE_SEL slice, and source from A53 CCM clk root when we need to
change ARM PLL frequency. Thus, we can support core running above
1GHz safely
- Update i.MX pfdv2 driver to check zero rate and use determine_rate for
getting the best rate
- Add CLKO2 for imx8mm, SNVS clock for imx8mn, and PXP clock for imx7d
- Remove PMC clks from Tegra clk driver
- Improved clock/reset handling for the Renesas R-Car USB2 Clock Selector
- Conversion to json-schema of the Renesas CPG/MSSR DT bindings
- Add Crypto clocks on Renesas R-Car M3-W/W+, M3-N, E3, and D3
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car H3, M3-W/W+, and M3-N
- Update Amlogic audio clock gate hierarchy for meson8 and gxbb
- Update Amlogic g12a spicc clock sources
- Support for Ingenic X1000 TCU clks
-----BEGIN PGP SIGNATURE-----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=ZoI6
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There's not much to see in the core framework this time around.
Instead the majority of the diff is the normal collection of driver
additions for new SoCs and non-critical clk data fixes and updates.
The framework must be middle aged.
The two biggest directories in the diffstat show that the Qualcomm and
Unisoc support added a handful of big drivers for new SoCs but that's
not really the whole story because those new drivers tend to add large
numbers of lines of clk data. There's a handful of AT91 clk drivers
added this time around too and a bunch of improvements to drivers like
the i.MX driver. All around lots of updates and fixes in various clk
drivers which is good to see.
The core framework has only one real major change which has been
baking in next for the past couple months. It fixes the framework so
that it stops caching a clk's phase when the phase clk_op returns an
error. Before this change we would consider some negative errno as a
phase and that just doesn't make sense.
Core:
- Don't show clk phase when it is invalid
New Drivers:
- Add support for Unisoc SC9863A clks
- Qualcomm SM8250 RPMh and MSM8976 RPM clks
- Qualcomm SM8250 Global Clock Controller (GCC) support
- Qualcomm SC7180 Modem Clock Controller (MSS CC) support
- EHRPWM's TimeBase clock(TBCLK) for TI AM654 SoCs
- Support PMC clks on at91sam9n12, at91rm9200, sama5d3, and
at91sam9g45 SoCs
Updates:
- GPU GX GDSC support on Qualcomm sc7180
- Fixes and improvements for the Marvell MMP2/MMP3 SoC clk drivers
- A series from Anson to convert i.MX8 clock bindings to json-schema
- Update i.MX pll14xx driver to include new frequency entries for
pll1443x table, and return error for invalid PLL type
- Add missing of_node_put() call for a number of i.MX clock drivers
- Drop flag CLK_IS_CRITICAL from 'A53_CORE' mux clock, as we already
have the flag on its child cpu clock
- Fix a53 cpu clock for i.MX8 drivers to get it source from ARM PLL
via CORE_SEL slice, and source from A53 CCM clk root when we need
to change ARM PLL frequency. Thus, we can support core running
above 1GHz safely
- Update i.MX pfdv2 driver to check zero rate and use determine_rate
for getting the best rate
- Add CLKO2 for imx8mm, SNVS clock for imx8mn, and PXP clock for
imx7d
- Remove PMC clks from Tegra clk driver
- Improved clock/reset handling for the Renesas R-Car USB2 Clock
Selector
- Conversion to json-schema of the Renesas CPG/MSSR DT bindings
- Add Crypto clocks on Renesas R-Car M3-W/W+, M3-N, E3, and D3
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car H3, M3-W/W+, and
M3-N
- Update Amlogic audio clock gate hierarchy for meson8 and gxbb
- Update Amlogic g12a spicc clock sources
- Support for Ingenic X1000 TCU clks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (146 commits)
clk: sprd: fix to get a correct ibias of pll
dt-bindings: imx8mm-clock: Fix the file path
dt-bindings: imx8mq-clock: Fix the file path
clk: qcom: rpmh: Drop unnecessary semicolons
clk: qcom: rpmh: Simplify clk_rpmh_bcm_send_cmd()
clk: tegra: Use NULL for pointer initialization
clk: sprd: add clocks support for SC9863A
clk: sprd: support to get regmap from parent node
clk: sprd: Add macros for referencing parents without strings
clk: sprd: Add dt-bindings include file for SC9863A
dt-bindings: clk: sprd: add bindings for sc9863a clock controller
dt-bindings: clk: sprd: rename the common file name sprd.txt to SoC specific
clk: sprd: add gate for pll clocks
MAINTAINERS: dt: update reference for arm-integrator.txt
clk: mmp2: Fix bit masks for LCDC I/O and pixel clocks
clk: mmp2: Add clock for fifth SD HCI on MMP3
dt-bindings: marvell,mmp2: Add clock id for the fifth SD HCI on MMP3
clk: mmp2: Add clocks for the thermal sensors
dt-bindings: marvell,mmp2: Add clock ids for the thermal sensors
clk: mmp2: add the GPU clocks
...
Commit 2760878662 ("clk: Bail out when calculating phase fails during
clk registration") introduced a check on error values at the time the
clock is registered to bail out when such an error occurs. However, it
doesn't check whether the returned value is positive which will happen
if the driver returns a non-zero phase. Since a phase is usually a
non-zero positive number this ends up returning something that isn't 0
to the caller of __clk_core_init(), making most clks fail to register
if they implement a phase clk op and return anything besides 0 for the
phase.
Fix this by returning the error if phase is less than zero or just
return zero if the phase is a positive number.
Fixes: 2760878662 ("clk: Bail out when calculating phase fails during clk registration")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lkml.kernel.org/r/20200225134248.919889-1-maxime@cerno.tech
Reported-by: "kernelci.org bot" <bot@kernelci.org>
[sboyd@kernel.org: Reword commit text to provide clarity]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The second line of the of_clk_detect_critical() function signature is
not indented according to coding style.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lkml.kernel.org/r/20191206133414.23925-1-geert+renesas@glider.be
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Bail out of clk registration if we fail to get the phase for a clk that
has a clk_ops::get_phase() callback. Print a warning too so that driver
authors can easily figure out that some clk is unable to read back phase
information at boot.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200205232802.29184-5-sboyd@kernel.org
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
There's some confusion about when recalc is done for the rate and
accuracy clk consumer APIs in relation to the prepare lock being taken.
Oddly enough, we take the lock again in debugfs APIs so that we can call
the internal "clk_core" APIs to get these fields with any necessary
recalculations. Instead of having this confusion, let's introduce a
recalc variant of these two consumer APIs as internal helpers and call
them from the consumer APIs and the debugfs code so that we don't take
the lock more than once.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200205232802.29184-4-sboyd@kernel.org
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Some lines are getting long in this function. Let's move 'parent' up to
the top of the function and use it in many places whenever there is a
parent for a clk. This shortens some lines by avoiding core->parent->
indirections.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200205232802.29184-3-sboyd@kernel.org
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
We don't check for errors from clk_ops::get_phase() before storing away
the result into the clk_core::phase member. This can lead to some fairly
confusing debugfs information if these ops do return an error. Let's
skip the store when this op fails to fix this. While we're here, move
the locking outside of clk_core_get_phase() to simplify callers from
the debugfs side.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200205232802.29184-2-sboyd@kernel.org
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Linus Torvalds
Stephen Boyd
Taniya Das
Sam Protsenko
Mike Tipton
Claudiu Beznea
Tudor Ambarus
Greg Kroah-Hartman
Lukasz Bartosik
Geert Uytterhoeven
Rasmus Villemoes
Saravana Kannan
Nicolas Pitre
Maxime Ripard
Dmitry Osipenko
Jerome Brunet
Lukas Bulwahn
Joe Perches
Julia Lawall
Mike Tipton
Sarang Mairal
Rafael J. Wysocki
YueHaibing
Marc Zyngier
Andy Shevchenko