The variable last_block is not needed.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ashish Sangwan <a.sangwan@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Incrementing lenExtents even while writing to a hole is bad
for performance as calls to udf_discard_prealloc and
udf_truncate_tail_extent would not return from start if
isize != lenExtents
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ashish Sangwan <a.sangwan@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Need to brelse the buffer_head stored in cur_epos and next_epos.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ashish Sangwan <a.sangwan@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Pull ext3 & udf fixes from Jan Kara:
"Shortlog pretty much says it all.
The interesting bits are UDF support for direct IO and ext3 fix for a
long standing oops in data=journal mode."
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
jbd: Fix assertion failure in commit code due to lacking transaction credits
UDF: Add support for O_DIRECT
ext3: Replace 0 with NULL for pointer in super.c file
udf: add writepages support for udf
ext3: don't clear orphan list on ro mount with errors
reiserfs: Make reiserfs_xattr_handlers static
Pull user namespace changes from Eric Biederman:
"This is a mostly modest set of changes to enable basic user namespace
support. This allows the code to code to compile with user namespaces
enabled and removes the assumption there is only the initial user
namespace. Everything is converted except for the most complex of the
filesystems: autofs4, 9p, afs, ceph, cifs, coda, fuse, gfs2, ncpfs,
nfs, ocfs2 and xfs as those patches need a bit more review.
The strategy is to push kuid_t and kgid_t values are far down into
subsystems and filesystems as reasonable. Leaving the make_kuid and
from_kuid operations to happen at the edge of userspace, as the values
come off the disk, and as the values come in from the network.
Letting compile type incompatible compile errors (present when user
namespaces are enabled) guide me to find the issues.
The most tricky areas have been the places where we had an implicit
union of uid and gid values and were storing them in an unsigned int.
Those places were converted into explicit unions. I made certain to
handle those places with simple trivial patches.
Out of that work I discovered we have generic interfaces for storing
quota by projid. I had never heard of the project identifiers before.
Adding full user namespace support for project identifiers accounts
for most of the code size growth in my git tree.
Ultimately there will be work to relax privlige checks from
"capable(FOO)" to "ns_capable(user_ns, FOO)" where it is safe allowing
root in a user names to do those things that today we only forbid to
non-root users because it will confuse suid root applications.
While I was pushing kuid_t and kgid_t changes deep into the audit code
I made a few other cleanups. I capitalized on the fact we process
netlink messages in the context of the message sender. I removed
usage of NETLINK_CRED, and started directly using current->tty.
Some of these patches have also made it into maintainer trees, with no
problems from identical code from different trees showing up in
linux-next.
After reading through all of this code I feel like I might be able to
win a game of kernel trivial pursuit."
Fix up some fairly trivial conflicts in netfilter uid/git logging code.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (107 commits)
userns: Convert the ufs filesystem to use kuid/kgid where appropriate
userns: Convert the udf filesystem to use kuid/kgid where appropriate
userns: Convert ubifs to use kuid/kgid
userns: Convert squashfs to use kuid/kgid where appropriate
userns: Convert reiserfs to use kuid and kgid where appropriate
userns: Convert jfs to use kuid/kgid where appropriate
userns: Convert jffs2 to use kuid and kgid where appropriate
userns: Convert hpfs to use kuid and kgid where appropriate
userns: Convert btrfs to use kuid/kgid where appropriate
userns: Convert bfs to use kuid/kgid where appropriate
userns: Convert affs to use kuid/kgid wherwe appropriate
userns: On alpha modify linux_to_osf_stat to use convert from kuids and kgids
userns: On ia64 deal with current_uid and current_gid being kuid and kgid
userns: On ppc convert current_uid from a kuid before printing.
userns: Convert s390 getting uid and gid system calls to use kuid and kgid
userns: Convert s390 hypfs to use kuid and kgid where appropriate
userns: Convert binder ipc to use kuids
userns: Teach security_path_chown to take kuids and kgids
userns: Add user namespace support to IMA
userns: Convert EVM to deal with kuids and kgids in it's hmac computation
...
Add support for the O_DIRECT flag. There are two cases to deal with:
1. Small files stored in the ICB (inode control block?): just return 0
from the new udf_adinicb_direct_IO() handler to fall back to buffered
I/O.
2. Larger files, not stored in the ICB: nothing special here. Just call
blockdev_direct_IO() from our new udf_direct_IO() handler and tidy up
any blocks instantiated outside i_size on error. This is pretty
standard. Factor error handling code out of udf_write_begin() into new
function udf_write_failed() so it can also be called by udf_direct_IO().
Also change the whitespace in udf_aops to make it a bit neater.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Jan Kara <jack@suse.cz>
If the new size is larger than the old size and the old file data was
stored in the ICB (iinfo->i_alloc_type == ICBTAG_FLAG_AD_IN_ICB) and the
new size still fits in the ICB, skip the call to udf_extend_file() as it
does not handle this i_alloc_type value (it calls BUG()).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Jan Kara <jack@suse.cz>
The variable "offset" is not needed. Remove it.
Signed-off-by: Ashish Sangwan <ashish.sangwan2@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
After we moved inode_sync_wait() from end_writeback() it doesn't make sense
to call the function end_writeback() anymore. Rename it to clear_inode()
which well says what the function really does - set I_CLEAR flag.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
ECMA 1.67 requires setting logicalBlocksRecorded to zero if the file
has no extents. This should be checked in udf_update_inode().
udf_fill_inode() will then take care of itself.
Signed-off-by: Steven P. Nickel <snickel@focusinfo.com>
Signed-off-by: Jan Kara <jack@suse.cz>
In accordance with ECMA 1.67 Part 4, 14.9.15, the checkpoint field
should be initialized to 1 at creation. (Zero is *not* a valid value.)
Signed-off-by: Steven P. Nickel <snickel@focusinfo.com>
Signed-off-by: Jan Kara <jack@suse.cz>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext2/3/4: delete unneeded includes of module.h
ext{3,4}: Fix potential race when setversion ioctl updates inode
udf: Mark LVID buffer as uptodate before marking it dirty
ext3: Don't warn from writepage when readonly inode is spotted after error
jbd: Remove j_barrier mutex
reiserfs: Force inode evictions before umount to avoid crash
reiserfs: Fix quota mount option parsing
udf: Treat symlink component of type 2 as /
udf: Fix deadlock when converting file from in-ICB one to normal one
udf: Cleanup calling convention of inode_getblk()
ext2: Fix error handling on inode bitmap corruption
ext3: Fix error handling on inode bitmap corruption
ext3: replace ll_rw_block with other functions
ext3: NULL dereference in ext3_evict_inode()
jbd: clear revoked flag on buffers before a new transaction started
ext3: call ext3_mark_recovery_complete() when recovery is really needed
During BKL removal in 2.6.38, conversion of files from in-ICB format to normal
format got broken. We call ->writepage with i_data_sem held but udf_get_block()
also acquires i_data_sem thus creating A-A deadlock.
We fix the problem by dropping i_data_sem before calling ->writepage() which is
safe since i_mutex still protects us against any changes in the file. Also fix
pagelock - i_data_sem lock inversion in udf_expand_file_adinicb() by dropping
i_data_sem before calling find_or_create_page().
CC: stable@kernel.org
Reported-by: Matthias Matiak <netzpython@mail-on.us>
Tested-by: Matthias Matiak <netzpython@mail-on.us>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
inode_getblk() always returned NULL and passed results in its parameters.
Make the function return something useful - found block number.
Signed-off-by: Jan Kara <jack@suse.cz>
note re mount options: fmask and dmask are explicitly truncated to 12bit,
UDF_INVALID_MODE just needs to be guaranteed to differ from any such value.
And umask is used only in &= with umode_t, so we ignore other bits anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Replace remaining direct i_nlink updates with a new set_nlink()
updater function.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Tested-by: Toshiyuki Okajima <toshi.okajima@jp.fujitsu.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Just whitespace and argument alignment.
Introduce some checkpatch warnings that deserve to be ignored.
Reviewed-by: NamJae Jeon <linkinjeon@gmail.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Use the current logging styles.
Convert a few printks that should have been udf_warn and udf_err.
Coalesce formats. Add #define pr_fmt.
Move an #include "udfdecls.h" above other includes in udftime.c
so pr_fmt works correctly. Strip prefixes from conversions as appropriate.
Reorder logging definitions in udfdecl.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Use mpage_readpages() instead of multiple calls to udf_readpage() to reduce the
CPU utilization and make performance higher.
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
* 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block: (65 commits)
Documentation/iostats.txt: bit-size reference etc.
cfq-iosched: removing unnecessary think time checking
cfq-iosched: Don't clear queue stats when preempt.
blk-throttle: Reset group slice when limits are changed
blk-cgroup: Only give unaccounted_time under debug
cfq-iosched: Don't set active queue in preempt
block: fix non-atomic access to genhd inflight structures
block: attempt to merge with existing requests on plug flush
block: NULL dereference on error path in __blkdev_get()
cfq-iosched: Don't update group weights when on service tree
fs: assign sb->s_bdi to default_backing_dev_info if the bdi is going away
block: Require subsystems to explicitly allocate bio_set integrity mempool
jbd2: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
jbd: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
fs: make fsync_buffers_list() plug
mm: make generic_writepages() use plugging
blk-cgroup: Add unaccounted time to timeslice_used.
block: fixup plugging stubs for !CONFIG_BLOCK
block: remove obsolete comments for blkdev_issue_zeroout.
blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
...
Fix up conflicts in fs/{aio.c,super.c}
Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The udf_readdir(), udf_lookup(), udf_create(), udf_mknod(), udf_mkdir(),
udf_rmdir(), udf_link(), udf_get_parent() and udf_unlink() seems already
adequately protected by i_mutex held by VFS invoking calls. The udf_rename()
instead should be already protected by lock_rename again by VFS. The
udf_ioctl(), udf_fill_super() and udf_evict_inode() don't requires any further
protection.
This work was supported by a hardware donation from the CE Linux Forum.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Jan Kara <jack@suse.cz>
Replace bkl with the UDF_I(inode)->i_data_sem rw semaphore in
udf_release_file(), udf_symlink(), udf_symlink_filler(), udf_get_block(),
udf_block_map(), and udf_setattr(). The rule now is that any operation
on regular file's or symlink's extents (or generally allocation information
including goal block) needs to hold i_data_sem.
This work was supported by a hardware donation from the CE Linux Forum.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Jan Kara <jack@suse.cz>
Superblock carries credentials (uid, gid, etc.) which are used as default
values in __udf_read_inode() when media does not provide these. These
credentials can change during remount so we protect them by a rwlock so that
each inode gets a consistent set of credentials.
Signed-off-by: Jan Kara <jack@suse.cz>
udf_update_inode() does not need BKL since on-disk inode modifications are
protected by the buffer lock and reading of values of in-memory inode is
safe without any lock. In some cases we can write inconsistent inode state
to disk but in that case inode will be marked dirty and overwritten later.
Also make unnecessarily global udf_sync_inode() static.
Signed-off-by: Jan Kara <jack@suse.cz>
Move the call to vmtruncate to get rid of accessive blocks to the callers
in preparation of the new truncate sequence and rename the non-truncating
version to block_write_begin.
While we're at it also remove several unused arguments to block_write_begin.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Quota on UDF is non-functional at least since 2.6.16 (I'm too lazy to
do more archeology) because it does not provide .quota_write and .quota_read
functions and thus quotaon(8) just returns EINVAL. Since nobody complained
for all those years and quota support is not even in UDF standard just nuke
it.
Signed-off-by: Jan Kara <jack@suse.cz>
generic setattr not longer responsible for quota transfer.
use udf_setattr for all udf's inodes.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6:
udf: use ext2_find_next_bit
udf: Do not read inode before writing it
udf: Fix unalloc space handling in udf_update_inode
Writing of inode holding unallocated space info was broken because we first
cleared the buffer and after that checked whether it contains a tag meaning the
block holds unallocated space information. Fix the problem by checking
appropriate in memory flag instead.
Also cleanup the function a bit along the way - most importantly lock buffer
when modifying its contents, check for buffer_write_io_error instead of
!buffer_uptodate, etc..
Signed-off-by: Jan Kara <jack@suse.cz>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6: (33 commits)
quota: stop using QUOTA_OK / NO_QUOTA
dquot: cleanup dquot initialize routine
dquot: move dquot initialization responsibility into the filesystem
dquot: cleanup dquot drop routine
dquot: move dquot drop responsibility into the filesystem
dquot: cleanup dquot transfer routine
dquot: move dquot transfer responsibility into the filesystem
dquot: cleanup inode allocation / freeing routines
dquot: cleanup space allocation / freeing routines
ext3: add writepage sanity checks
ext3: Truncate allocated blocks if direct IO write fails to update i_size
quota: Properly invalidate caches even for filesystems with blocksize < pagesize
quota: generalize quota transfer interface
quota: sb_quota state flags cleanup
jbd: Delay discarding buffers in journal_unmap_buffer
ext3: quota_write cross block boundary behaviour
quota: drop permission checks from xfs_fs_set_xstate/xfs_fs_set_xquota
quota: split out compat_sys_quotactl support from quota.c
quota: split out netlink notification support from quota.c
quota: remove invalid optimization from quota_sync_all
...
Fixed trivial conflicts in fs/namei.c and fs/ufs/inode.c
This gives the filesystem more information about the writeback that
is happening. Trond requested this for the NFS unstable write handling,
and other filesystems might benefit from this too by beeing able to
distinguish between the different callers in more detail.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Get rid of the initialize dquot operation - it is now always called from
the filesystem and if a filesystem really needs it's own (which none
currently does) it can just call into it's own routine directly.
Rename the now static low-level dquot_initialize helper to __dquot_initialize
and vfs_dq_init to dquot_initialize to have a consistent namespace.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Currently various places in the VFS call vfs_dq_init directly. This means
we tie the quota code into the VFS. Get rid of that and make the
filesystem responsible for the initialization. For most metadata operations
this is a straight forward move into the methods, but for truncate and
open it's a bit more complicated.
For truncate we currently only call vfs_dq_init for the sys_truncate case
because open already takes care of it for ftruncate and open(O_TRUNC) - the
new code causes an additional vfs_dq_init for those which is harmless.
For open the initialization is moved from do_filp_open into the open method,
which means it happens slightly earlier now, and only for regular files.
The latter is fine because we don't need to initialize it for operations
on special files, and we already do it as part of the namespace operations
for directories.
Add a dquot_file_open helper that filesystems that support generic quotas
can use to fill in ->open.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Get rid of the drop dquot operation - it is now always called from
the filesystem and if a filesystem really needs it's own (which none
currently does) it can just call into it's own routine directly.
Rename the now static low-level dquot_drop helper to __dquot_drop
and vfs_dq_drop to dquot_drop to have a consistent namespace.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Currently clear_inode calls vfs_dq_drop directly. This means
we tie the quota code into the VFS. Get rid of that and make the
filesystem responsible for the drop inside the ->clear_inode
superblock operation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Some misspelled occurences of 'octet' and some comments were also fixed
as I was on it.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is not very good to do IO in udf_clear_inode. First, VFS does not really
expect inode to become dirty there and thus we have to write it ourselves,
second, memory reclaim gets blocked waiting for IO when it does not really
expect it, third, the IO pattern (e.g. on umount) resulting from writes in
udf_clear_inode is bad and it slows down writing a lot.
The reason why UDF needed to do IO in udf_clear_inode is that UDF standard
mandates extent length to exactly match inode size. But when we allocate
extents to a file or directory, we don't really know what exactly the final
file size will be and thus temporarily set it to block boundary and later
truncate it to exact length in udf_clear_inode. Now, this is changed to
truncate to final file size in udf_release_file for regular files. For
directories and symlinks, we do the truncation at the moment when learn
what the final file size will be.
Signed-off-by: Jan Kara <jack@suse.cz>
So far we preallocated blocks also for directories but that brings a
problem, when to get rid of preallocated blocks we don't need. So far
we removed them in udf_clear_inode() which has a disadvantage that
1) blocks are unavailable long after writing to a directory finished
and thus one can get out of space unnecessarily early
2) releasing blocks from udf_clear_inode is problematic because VFS
does not expect us to redirty inode there and it also slows down
memory reclaim.
So preallocate blocks only for regular files where we can drop preallocation
in udf_release_file.
Signed-off-by: Jan Kara <jack@suse.cz>
On x86 (and several other archs) mode_t is defined as "unsigned short"
and comparing unsigned shorts to negative ints is broken (because short
is promoted to int and then compared). Fix it.
Reported-and-tested-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
"dmode" allows overriding permissions of directories and
"mode" allows overriding permissions of files.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Jan Kara <jack@suse.cz>
Namjae Jeon
Linus Torvalds
Eric W. Biederman
Ian Abbott
Namjae Jeon
Ashish Sangwan
Jan Kara
Steve Nickel
Al Viro
Miklos Szeredi
Joe Perches
Jens Axboe
Alessio Igor Bogani
Christoph Hellwig
Dmitry Monakhov
Jiri Kosina
Christoph Hellwig
Daniel Mack
Marcin Slusarz
Pekka Enberg