* 'for-2.6.28' of git://linux-nfs.org/~bfields/linux:
NLM: client-side nlm_lookup_host() should avoid matching on srcaddr
nfsd: use of unitialized list head on error exit in nfs4recover.c
Add a reference to sunrpc in svc_addsock
nfsd: clean up grace period on early exit
Due to a wrong safety check in af_can.c it was not possible to filter
for SFF frames with a specific CAN identifier without getting the
same selected CAN identifier from a received EFF frame also.
This fix has a minimum (but user visible) impact on the CAN filter
API and therefore the CAN version is set to a new date.
Indeed the 'old' API is still working as-is. But when now setting
CAN_(EFF|RTR)_FLAG in can_filter.can_mask you might get less traffic
than before - but still the stuff that you expected to get for your
defined filter ...
Thanks to Kurt Van Dijck for pointing at this issue and for the review.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Installing SAs using the XFRM_STATE_AF_UNSPEC fails on hosts with
support for one address family only. This patch accepts such SAs, even
if the processing of not supported packets will fail.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a potential NULL pointer dereference seen when trying to remove a
static label configuration with an invalid address/mask combination.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Used __xfrm_policy_unlink() to instead of the dup codes when unlink
SPD entry.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After flush the SPD entries, dump the SPD entries will cause kernel painc.
Used the following commands to reproduct:
- echo 'spdflush;' | setkey -c
- echo 'spdadd 3ffe:501:ffff:ff01::/64 3ffe:501:ffff:ff04::/64 any -P out ipsec \
ah/tunnel/3ffe:501:ffff:ff00:200:ff:fe00:b0b0-3ffe:501:ffff:ff02:200:ff:fe00:a1a1/require;\
spddump;' | setkey -c
- echo 'spdflush; spddump;' | setkey -c
- echo 'spdadd 3ffe:501:ffff:ff01::/64 3ffe:501:ffff:ff04::/64 any -P out ipsec \
ah/tunnel/3ffe:501:ffff:ff00:200:ff:fe00:b0b0-3ffe:501:ffff:ff02:200:ff:fe00:a1a1/require;\
spddump;' | setkey -c
This is because when flush the SPD entries, the SPD entry is not remove
from the list.
This patch fix the problem by remove the SPD entry from the list.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a lockdep report by Alexey Dobriyan.
I checked all per_cpu_counter_xxx() usages in network tree, and I
think all call sites are BH enabled except one in
inet_csk_listen_stop().
commit dd24c00191
(net: Use a percpu_counter for orphan_count)
replaced atomic_t orphan_count to a percpu_counter.
atomic_inc()/atomic_dec() can be called from any context, while
percpu_counter_xxx() should be called from a consistent state.
For orphan_count, this context can be the BH-enabled one.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the post-processing of feature negotiation state, after
the negotiation has completed.
To this purpose, handlers are used and added to the dccp_feat_table. Each
handler is passed a boolean flag whether the RX or TX side of the feature
is meant.
Several handlers are provided already, new handlers can easily be added.
The initialisation is now fully dynamic, i.e. CCIDs are activated only
after the feature negotiation. The integration of this dynamic activation
is done in the subsequent patches.
Thanks to Wei Yongjun for pointing out the necessity of skipping over empty
Confirm options while copying the negotiated feature values.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Analogous to the previous patch, this adds code to interpret incoming Confirm
feature-negotiation options. Both functions operate on the feature-negotiation
list of either the request_sock (server) or the dccp_sock (client).
Thanks to Wei Yongjun for pointing out that it is overly restrictive to check
the entire list of confirmed SP values.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds/replaces code for processing incoming ChangeL/R options.
The main difference is that:
* mandatory FN options are now interpreted inside the function
(there are too many individual cases to do this externally);
* the function returns an appropriate Reset code or 0,
which is then used to fill in the data for the Reset packet.
Old code, which is no longer used or referenced, has been removed.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides two functions to
* reconcile preference lists (with appropriate return codes) and
* reorder the preference list if successful reconciliation changed the
preferred value.
The patch also removes the old code for processing SP/NN Change options, since
new code to process these is mostly there already; related references have been
commented out.
The code for processing Change options follows in the next patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch implements insertion of feature negotiation at the server (listening
and request socket) and the client (connecting socket).
In dccp_insert_options(), several statements have been grouped together now
to achieve (it is hoped) better efficiency by reducing the number of tests
each packet has to go through:
- Ack Vectors are sent if the packet is neither a Data or a Request packet;
- a previous issue is corrected - feature negotiation options are allowed
on DataAck packets (5.8).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the earlier insertion routine from options.c, so that
code specific to feature negotiation can remain in feat.c. This is possible
by calling a function already existing in options.c.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that the following sequence of actions will reproduce the
oops:
1. Create a new RFCOMM device (using RFCOMMCREATEDEV ioctl)
2. (Try to) open the device
3. Release the RFCOMM device (using RFCOMMRELEASEDEV ioctl)
At this point, the "/dev/rfcomm*" device is still in use, but it is gone
from the internal list, so the device id can be reused.
4. Create a new RFCOMM device with the same device id as before
And now kobject will complain that the TTY already exists.
(See http://lkml.org/lkml/2008/7/13/89 for a reproducible test-case.)
This patch attempts to correct this by only removing the device from the
internal list of devices at the final unregister stage, so that the id
won't get reused until the device has been completely destructed.
This should be safe as the RFCOMM_TTY_RELEASED bit will be set for the
device and prevent the device from being reopened after it has been
released.
Based on a report from Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Newer GCC versions are a little bit picky about how to deal with format
arguments:
net/bluetooth/hci_sysfs.c: In function ‘hci_register_sysfs’:
net/bluetooth/hci_sysfs.c:418: warning: format not a string literal and no format arguments
It is simple enough to fix and makes the compiler happy.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the introduction of CONFIG_DYNAMIC_PRINTK_DEBUG it is possible to
allow debugging without having to recompile the kernel. This patch turns
all BT_DBG() calls into pr_debug() to support dynamic debug messages.
As a side effect all CONFIG_BT_*_DEBUG statements are now removed and
some broken debug entries have been fixed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth subsystem was not using the HCI Reset command when doing
device initialization. The Bluetooth 1.0b specification was ambiguous
on how the device firmware was suppose to handle it. Almost every device
was triggering a transport reset at the same time. In case of USB this
ended up in disconnects from the bus.
All modern Bluetooth dongles handle this perfectly fine and a lot of
them actually require that HCI Reset is sent. If not then they are
either stuck in their HID Proxy mode or their internal structures for
inquiry and paging are not correctly setup.
To handle old and new devices smoothly the Bluetooth subsystem contains
a quirk to force the HCI Reset on initialization. However maintaining
such a quirk becomes more and more complicated. This patch turns the
logic around and lets the old devices disable the HCI Reset command.
The only device where the HCI_QUIRK_NO_RESET is still needed are the
original Digianswer devices and dongles with an early CSR firmware.
CSR reported that they fixed this for version 12 firmware. The last
official release of version 11 firmware is build ID 115. The first
version 12 candidate was build ID 117.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After adding proper lockdep annotations for Bluetooth protocols the case
when lockdep is disabled produced two compiler warnings:
net/bluetooth/af_bluetooth.c:60: warning: ‘bt_key_strings’ defined but not used
net/bluetooth/af_bluetooth.c:71: warning: ‘bt_slock_key_strings’ defined but not used
Fix both of them by adding a CONFIG_DEBUG_LOCK_ALLOC conditional around
them and re-arranging the code a little bit.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
struct hci_dev_list_req {
__u16 dev_num;
struct hci_dev_req dev_req[0]; /* hci_dev_req structures */
};
sizeof(struct hci_dev_list_req) == 4, so the two bytes immediately
following "dev_num" will never be initialized. When this structure
is copied to userspace, these uninitialized bytes are leaked.
Fix by using kzalloc() instead of kmalloc(). Found using kmemcheck.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Impact: make global function static
Fix the following sparse warning:
net/sched/sch_api.c:192:14: warning: symbol 'qdisc_match_from_root' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
validate_nla() currently doesn't allow empty nested attributes. This
makes userspace code unnecessarily complicated when starting and ending
the nested attribute is done by generic upper level code and the inner
attributes are dumped by a module.
Add a special case to accept empty nested attributes. When the nested
attribute is non empty, the same checks as before are performed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix missing label when CONFIG_PROC_FS=n:
net/sctp/protocol.c: In function 'sctp_proc_init':
net/sctp/protocol.c:106: error: label 'out_nomem' used but not defined
make[3]: *** [net/sctp/protocol.o] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Reviewed-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an implementation of David Miller's suggested fix in:
https://bugzilla.redhat.com/show_bug.cgi?id=470201
It has been updated to use wait_event() instead of
wait_event_interruptible().
Paraphrasing the description from the above report, it makes sendmsg()
block while UNIX garbage collection is in progress. This avoids a
situation where child processes continue to queue new FDs over a
AF_UNIX socket to a parent which is in the exit path and running
garbage collection on these FDs. This contention can result in soft
lockups and oom-killing of unrelated processes.
Signed-off-by: dann frazier <dannf@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A NULL dereference would occur when trying to delete an addres from a
network device that does not have any Phonet address.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since all other gen_estimator functions use bstats and rate_est params
together, and searching for them is optimized now, let's use this also
in gen_estimator_active(). The return type of gen_estimator_active()
is changed to bool, and gen_find_node() parameters to const, btw.
In tcf_act_police_locate() a check for ACT_P_CREATED is added before
calling gen_estimator_active().
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be consistent with NL80211_ATTR_POWER_RULE_MAX_EIRP,
change NL80211_FREQUENCY_ATTR_MAX_TX_POWER to use mBm and U32 instead
of dBm and U8. This is a userspace interface change, but the previous
version had not yet been pushed upstream and there are no userspace
programs using this yet, so there is justification to get this change in
as long as it goes in before the previous version gets out.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We "optimize" away the get_state() hook call on rfkill_toggle_radio
when doing a forced state change. This means the resume path is not
calling get_state() as it should.
Call it manually on the resume handler, as we don't want to mess with
the EPO path by removing the optimization. This has the added benefit
of making it explicit that rfkill->state could have been modified
before we hit the rfkill_toggle_radio() call in the class resume
handler.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rfkill class API requires that the driver connected to a class
call rfkill_force_state() on resume to update the real state of the
rfkill controller, OR that it provides a get_state() hook.
This means there is potentially a hidden call in the resume code flow
that changes rfkill->state (i.e. rfkill_force_state()), so the
previous state of the transmitter was being lost.
The simplest and most future-proof way to fix this is to explicitly
store the pre-sleep state on the rfkill structure, and restore from
that on resume.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a disassoc packet is received from the AP with a reason code of
'leaving the BSS', mac80211 should go into DISABLED state just as it
would do if the AP suddenly went away for some reason, as that is what
will happen shortly after the AP leaves anyway.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is useful information to provide for userspace (e.g., hostapd needs
this to generate Country IE).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit 9ea2c74 named "mac80211/drivers: rewrite the rate control API",
the meaning of status.rates[i].count was changed from number of retries
to total number of tries. As a result, the pid rate-setting algorithm fails
because every packet appears to have needed a retransmit.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes minstrel the default rate control algorithm
for mac80211. For more information see:
http://wireless.kernel.org/en/developers/Documentation/mac80211/RateControl/minstrel
If someone can come up with a better algorithm they get a prize
(undisclosed).
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous fix for the conntrack creation race (netfilter: ctnetlink:
fix conntrack creation race) missed a GFP_KERNEL allocation that is
now performed while holding a spinlock. Switch to GFP_ATOMIC.
Reported-and-tested-by: Zoltan Borbely <bozo@andrews.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When queuing a skb to sk->sk_receive_queue, we can release its dst,
not anymore needed. Since current cpu did the dst_hold(), refcount is
probably still hot int this cpu caches.
This avoids readers to access the original dst to decrement its
refcount, possibly a long time after packet reception. This should
speedup UDP and RAW receive path.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using one atomic_t per protocol, use a percpu_counter
for "orphan_count", to reduce cache line contention on
heavy duty network servers.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using one atomic_t per protocol, use a percpu_counter
for "sockets_allocated", to reduce cache line contention on
heavy duty network servers.
Note : We revert commit (248969ae31
net: af_unix can make unix_nr_socks visbile in /proc),
since it is not anymore used after sock_prot_inuse_add() addition
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found that while trying average rate policing, it was possible to
request average rate policing without a rate estimator. This results
in no policing which is harmless but incorrect.
Since policing could be setup in two steps, need to check
in the kernel.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions gen_new_estimator and gen_replace_estimator can return
errors, but they were being ignored.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow tcf_hash_create to return different errors on estimator failure.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The truesize message check is important enough to make it print "BUG"
to the user console... lets also make it important enough to spit a
backtrace/module list etc so that kerneloops.org can track them.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make
net.core.xfrm_aevent_etime
net.core.xfrm_acq_expires
net.core.xfrm_aevent_rseqth
net.core.xfrm_larval_drop
sysctls per-netns.
For that make net_core_path[] global, register it to prevent two
/proc/net/core antries and change initcall position -- xfrm_init() is called
from fs_initcall, so this one should be fs_initcall at least.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* interaction with userspace -- take netns from userspace socket.
* in ->notify hook take netns either from SA or explicitly passed --
we don't know if SA/SPD flush is coming.
* stub policy migration with init_net for now.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* netns boilerplate
* keep per-netns socket list
* keep per-netns number of sockets
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SA/SPD doesn't pin netns (and it shouldn't), so get rid of them by hand.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SA and SPD flush are executed with NULL SA and SPD respectively, for
these cases pass netns explicitly from userspace socket.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grab netns either from netlink socket, state or policy.
SA and SPD flush are in init_net for now, this requires little
attention, see below.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass netns pointer to struct xfrm_policy_afinfo::garbage_collect()
[This needs more thoughts on what to do with dst_ops]
[Currently stub to init_net]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass netns to xfrm_lookup()/__xfrm_lookup(). For that pass netns
to flow_cache_lookup() and resolver callback.
Take it from socket or netdevice. Stub DECnet to init_net.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netns parameter to xfrm_policy_bysel_ctx(), xfrm_policy_byidx().
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per-netns hashes are independently resizeable.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Again, to avoid complications with passing netns when not necessary.
Again, ->xp_net is set-once field, once set it never changes.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disallow spurious wakeups in __xfrm_lookup().
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
State GC is per-netns, and this is part of it.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
km_waitq is going to be made per-netns to disallow spurious wakeups
in __xfrm_lookup().
To not wakeup after every garbage-collected xfrm_state (which potentially
can be from different netns) make state GC list per-netns.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of this is implicit passing which netns's hashes should be resized.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hashtables are per-netns, they can be independently resized.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done to get
a) simple "something leaked" check
b) cover possible DoSes when other netns puts many, many xfrm_states
onto a list.
c) not miss "alien xfrm_state" check in some of list iterators in future.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid unnecessary complications with passing netns around.
* set once, very early after allocating
* once set, never changes
For a while create every xfrm_state in init_net.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix this warning:
net/bluetooth/rfcomm/sock.c: In function ‘rfcomm_sock_ioctl’:
net/bluetooth/rfcomm/sock.c:795: warning: unused variable ‘sk’
perhaps BT_DEBUG() should be improved to do printf format checking
instead of the #ifdef, but that looks quite intrusive: each bluetooth
.c file undefines the macro.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix this warning:
net/sunrpc/xprtrdma/verbs.c: In function ‘rpcrdma_conn_upcall’:
net/sunrpc/xprtrdma/verbs.c:279: warning: unused variable ‘addr’
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix this warning:
net/ax25/sysctl_net_ax25.c:27: warning: ‘min_ds_timeout’ defined but not used
net/ax25/sysctl_net_ax25.c:27: warning: ‘max_ds_timeout’ defined but not used
These are only used in the CONFIG_AX25_DAMA_SLAVE case.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
this warning:
net/dccp/options.c: In function ‘dccp_parse_options’:
net/dccp/options.c:67: warning: ‘value’ may be used uninitialized in this function
is a bogus GCC warning. The compiler does not recognize the relation
between "value" and "mandatory" variables: the code flow can ever reach
the "out_invalid_option:" label if 'mandatory' is set to 1, and when
'mandatory' is non-zero, we'll always have 'value' initialized.
Help out the compiler by annotating the variable.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
this warning:
net/dsa/mv88e6060.c: In function ‘mv88e6060_poll_link’:
net/dsa/mv88e6060.c:225: warning: ‘port_status’ may be used uninitialized in this function
triggers because GCC does not recognize the (correct) error flow
between 'link' and 'port_status'.
Annotate it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
this warning:
net/dsa/mv88e6xxx.c: In function ‘mv88e6xxx_poll_link’:
net/dsa/mv88e6xxx.c:361: warning: ‘port_status’ may be used uninitialized in this function
triggers because GCC does not recognize the (correct) error flow
between 'link' and 'port_status'.
Annotate it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
this warning:
net/ipv6/ip6_flowlabel.c: In function ‘ipv6_flowlabel_opt’:
net/ipv6/ip6_flowlabel.c:467: warning: ‘err’ may be used uninitialized in this function
triggers because GCC does not recognize the (correct) error flow
between fl_create() and 'err'.
Annotate it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
this warning:
net/sched/sch_hfsc.c: In function ‘hfsc_enqueue’:
net/sched/sch_hfsc.c:1577: warning: ‘err’ may be used uninitialized in this function
triggers because GCC does not recognize the (correct) error flow
between hfsc_classify(), 'cl' and 'err'.
Annotate it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
this warning:
net/sunrpc/xprtrdma/svc_rdma_transport.c: In function ‘svc_rdma_accept’:
net/sunrpc/xprtrdma/svc_rdma_transport.c:830: warning: ‘dma_mr_acc’ may be used uninitialized in this function
triggers because GCC does not recognize the (correct) flow connection
between need_dma_mr and dma_mr_acc.
Annotate it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will filter out the uevent not related to the init_net.
Without this patch if a network device is created in a network
namespace with the same name as one network device belonging to the
initial network namespace (eg. eth0), when the network namespace
will die and the network device will be destroyed, an event will
be sent and catched by the udevd daemon. That will result to have
the real network device to be shutdown because the udevd/uevent are
not namespace aware.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since pskb_expand_head creates copy of the shared area we
cannot keep any frag ptr past de-cloning. This fixes the
tcpdump recvfrom -EFAULT problem.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
After implementing qdisc->ops->peek() there is no more calling
qdisc_tree_decrease_qlen() without rtnl_lock(), so qdisc_list_lock
added by commit: f6e0b239a2 "pkt_sched:
Fix qdisc list locking" can be removed.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Optimization
Like done in inet_unhash(), we can avoid taking a chain lock if
socket is not hashed in udp_unhash()
Triggered by close(socket(AF_INET, SOCK_DGRAM, 0));
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
prot->destroy is not called with BH disabled. So we must add
explicit BH disable around call to sock_prot_inuse_add()
in sctp_destroy_sock()
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211's ieee80211_register_hw() is often called within the
probe path so it cannot assume the device's driver structure
has been attached yet so to create a workqueue instead of
using driver->name use the wiphy's phy%d name. The name doesn't
really matter anyway.
This should fix sporadic oopses found when we race to beat the
driver pointer setting. Not even sure how this was working properly.
http://www.kerneloops.org/search.php?search=ieee80211_register_hw
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds API to cfg80211 to allow wireless drivers to inform
us if their firmware can handle regulatory considerations *and*
they cannot map these regulatory domains to an ISO / IEC 3166
alpha2. In these cases we skip the first regulatory hint instead
of expecting the driver to build their own regulatory structure,
providing us with an alpha2, or using the reg_notifier().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds country IE parsing to mac80211 and enables its usage
within the new regulatory infrastructure in cfg80211. We parse
the country IEs only on management beacons for the BSSID you are
associated to and disregard the IEs when the country and environment
(indoor, outdoor, any) matches the already processed country IE.
To avoid following misinformed or outdated APs we build and use
a regulatory domain out of the intersection between what the AP
provides us on the country IE and what CRDA is aware is allowed
on the same country.
A secondary device is allowed to follow only the same country IE
as it make no sense for two devices on a system to be in two
different countries.
In the case the AP is using country IEs for an incorrect country
the user may help compliance further by setting the regulatory
domain before or after the IE is parsed and in that case another
intersection will be performed.
CONFIG_WIRELESS_OLD_REGULATORY is supported but requires CRDA
present.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lets remain consistent and mark rds with > NL80211_MAX_SUPP_REG_RULES
number of reg rules as invalid in is_valid_rd().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
kobject_uevent_env() can return an error but it just tells us
if the uvent was built/sent or not, it doesn't tell us anything
about what happened in userspace, whether the udev rule was present
nor does it tell us if CRDA was present or not. So remove
the informative complaint about it assuming it will tell us
such things.
Note that you can determine if CRDA is present after loading cfg80211
by using:
is_old_static_regdom(cfg80211_regdomain)
but this doesn't account for possible user install after initial
boot, and also for when the user uses the static EU regulatory
domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When intersecting it is possible that set_regdom() was called
with a regulatory domain which we'll only use as an aid to
build a final regulatory domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So far the __set_regdom() code is pretty generic as the
intersection case is fairly straight forward; this will however
change when 802.11d support is added so lets separate intersection
code for now in preparation for 802.11d support.
This patch only has slight functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have control over the REGDOM_SET_BY_* macros passed
so remove the switch.
This patch has no functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have complete control over REGDOM_SET_BY_* enum passed
down to __regulatory_hint() as such there is no need to
account for unexpected REGDOM_SET_BY_*'s, lets just remove
the switch statement as this code does not change and
won't change even when we add 802.11d support.
This patch has no functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Regulatory rules with negative frequencies are now
marked as invalid in is_valid_reg_rule().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
fix:
net/wireless/reg.c:348:29: error: macro "if" passed 2 arguments, but takes just 1
triggered by the branch-tracer.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes the kernel trace when user tries to set
ad-hoc mode on non IBSS channel.
e.g iwconfig wlan0 chan 36 mode ad-hoc
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this warning:
net/netfilter/nf_conntrack_ftp.c: In function 'help':
net/netfilter/nf_conntrack_ftp.c:360: warning: 'matchoff' may be used uninitialized in this function
net/netfilter/nf_conntrack_ftp.c:360: warning: 'matchlen' may be used uninitialized in this function
triggers because GCC does not recognize the (correct) error flow
between find_pattern(), 'found', 'matchoff' and 'matchlen'.
Annotate it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch let nfmark to be evaluated for routing decision for OUTPUT
packet, in mangle table, when process paquet in NFQUEUE. This patch is
an IPv6 port of Laurent Licour IPv4 one.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch let nfmark to be evaluated for routing decision for OUTPUT
packet, in mangle table, when process paquet in NFQUEUE
Until now, only change (in NFQUEUE process) on fields src_addr,
dest_addr and tos could make netfilter to reevalute the routing.
From: Laurent Licour <laurent@licour.com>
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Since the netlink option for DCB is necessary to actually be useful,
simplified the Kconfig option. In addition, added useful help text for the
Kconfig option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since changeset e79ad711a0 from mainline,
>From David S. Miller,
empty packet can be transmitted on connected socket for datagram protocols.
However, this patch broke a high level application using ROSE network protocol with connected datagram.
Bulletin Board Stations perform bulletins forwarding between BBS stations via ROSE network using a forward protocol.
Now, if for some reason, a buffer in the application software happens to be empty at a specific moment,
ROSE sends an empty packet via unfiltered packet socket.
When received, this ROSE packet introduces perturbations of data exchange of BBS forwarding,
for the application message forwarding protocol is waiting for something else.
We agree that a more careful programming of the application protocol would avoid this situation and we are
willing to debug it.
But, as an empty frame is no use and does not have any meaning for ROSE protocol,
we may consider filtering zero length data both when sending and receiving socket data.
The proposed patch repaired BBS data exchange through ROSE network that were broken since 2.6.22.11 kernel.
Signed-off-by: Bernard Pidoux <f6bvp@amsat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This caused me to get repeatably:
tcpdump: pcap_loop: recvfrom: Bad address
Happens occassionally when I tcpdump my for-looped test xfers:
while [ : ]; do echo -n "$(date '+%s.%N') "; ./sendfile; sleep 20; done
Rest of the relevant commands:
ethtool -K eth0 tso off
tc qdisc add dev eth0 root netem drop 4%
tcpdump -n -s0 -i eth0 -w sacklog.all
Running net-next under kvm, connection goes to the same host
(basically just out of kvm). The connection itself works ok
and data gets sent without corruption even with a large
number of tests while tcpdump fails usually within less than
5 tests.
Whether it only happens because of this change or not, I
don't know for sure but it's the only thing with which
I've seen that error. The non-cloned variant works w/o it
for much longer time. I'm yet to debug where the error
actually comes from.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The earlier version was just very basic one which is "playing
safe" by always clearing the hints. However, clearing of a hint
is extremely costly operation with large windows, so it must be
avoided at all cost whenever possible, there is a way with
shifting too achieve not-clearing.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
During SACK processing, most of the benefits of TSO are eaten by
the SACK blocks that one-by-one fragment SKBs to MSS sized chunks.
Then we're in problems when cleanup work for them has to be done
when a large cumulative ACK comes. Try to return back to pre-split
state already while more and more SACK info gets discovered by
combining newly discovered SACK areas with the previous skb if
that's SACKed as well.
This approach has a number of benefits:
1) The processing overhead is spread more equally over the RTT
2) Write queue has less skbs to process (affect everything
which has to walk in the queue past the sacked areas)
3) Write queue is consistent whole the time, so no other parts
of TCP has to be aware of this (this was not the case with
some other approach that was, well, quite intrusive all
around).
4) Clean_rtx_queue can release most of the pages using single
put_page instead of previous PAGE_SIZE/mss+1 calls
In case a hole is fully filled by the new SACK block, we attempt
to combine the next skb too which allows construction of skbs
that are even larger than what tso split them to and it handles
hole per on every nth patterns that often occur during slow start
overshoot pretty nicely. Though this to be really useful also
a retransmission would have to get lost since cumulative ACKs
advance one hole at a time in the most typical case.
TODO: handle upwards only merging. That should be rather easy
when segment is fully sacked but I'm leaving that as future
work item (it won't make very large difference anyway since
this current approach already covers quite a lot of normal
cases).
I was earlier thinking of some sophisticated way of tracking
timestamps of the first and the last segment but later on
realized that it won't be that necessary at all to store the
timestamp of the last segment. The cases that can occur are
basically either:
1) ambiguous => no sensible measurement can be taken anyway
2) non-ambiguous is due to reordering => having the timestamp
of the last segment there is just skewing things more off
than does some good since the ack got triggered by one of
the holes (besides some substle issues that would make
determining right hole/skb even harder problem). Anyway,
it has nothing to do with this change then.
I choose to route some abnormal looking cases with goto noop,
some could be handled differently (eg., by stopping the
walking at that skb but again). In general, they either
shouldn't happen at all or are rare enough to make no difference
in practice.
In theory this change (as whole) could cause some macroscale
regression (global) because of cache misses that are taken over
the round-trip time but it gets very likely better because of much
less (local) cache misses per other write queue walkers and the
big recovery clearing cumulative ack.
Worth to note that these benefits would be very easy to get also
without TSO/GSO being on as long as the data is in pages so that
we can merge them. Currently I won't let that happen because
DSACK splitting at fragment that would mess up pcounts due to
sk_can_gso in tcp_set_skb_tso_segs. Once DSACKs fragments gets
avoided, we have some conditions that can be made less strict.
TODO: I will probably have to convert the excessive pointer
passing to struct sacktag_state... :-)
My testing revealed that considerable amount of skbs couldn't
be shifted because they were cloned (most likely still awaiting
tx reclaim)...
[The rest is considering future work instead since I got
repeatably EFAULT to tcpdump's recvfrom when I added
pskb_expand_head to deal with clones, so I separated that
into another, later patch]
...To counter that, I gave up on the fifth advantage:
5) When growing previous SACK block, less allocs for new skbs
are done, basically a new alloc is needed only when new hole
is detected and when the previous skb runs out of frags space
...which now only happens of if reclaim is fast enough to dispose
the clone before the SACK block comes in (the window is RTT long),
otherwise we'll have to alloc some.
With clones being handled I got these numbers (will be somewhat
worse without that), taken with fine-grained mibs:
TCPSackShifted 398
TCPSackMerged 877
TCPSackShiftFallback 320
TCPSACKCOLLAPSEFALLBACKGSO 0
TCPSACKCOLLAPSEFALLBACKSKBBITS 0
TCPSACKCOLLAPSEFALLBACKSKBDATA 0
TCPSACKCOLLAPSEFALLBACKBELOW 0
TCPSACKCOLLAPSEFALLBACKFIRST 1
TCPSACKCOLLAPSEFALLBACKPREVBITS 318
TCPSACKCOLLAPSEFALLBACKMSS 1
TCPSACKCOLLAPSEFALLBACKNOHEAD 0
TCPSACKCOLLAPSEFALLBACKSHIFT 0
TCPSACKCOLLAPSENOOPSEQ 0
TCPSACKCOLLAPSENOOPSMALLPCOUNT 0
TCPSACKCOLLAPSENOOPSMALLLEN 0
TCPSACKCOLLAPSEHOLE 12
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is preparatory work for SACK combiner patch which may
have to count TCP state changes for only a part of the skb
because it will intentionally avoids splitting skb to SACKed
and not sacked parts.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sadly enough, this adds possible divide though we try to avoid
it by checking one mss as common case.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
I knew already when rewriting the sacktag that this condition
was too conservative, change it now since it prevent lot of
useless work (especially in the sack shifter decision code
that is being added by a later patch). This shouldn't change
anything really, just save some processing regardless of the
shifter.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
I always had thought that collapsing up to two at a time was
intentional decision to avoid excessive processing if 1 byte
sized skbs are to be combined for a full mtu, and consecutive
retransmissions would make the size of the retransmittee
double each round anyway, but some recent discussion made me
to understand that was not the case. Thus make collapse work
more and wait less.
It would be possible to take advantage of the shifting
machinery (added in the later patch) in the case of paged
data but that can be implemented on top of this change.
tcp_skb_is_last check is now provided by the loop.
I tested a bit (ss-after-idle-off, fill 4096x4096B xfer,
10s sleep + 4096 x 1byte writes while dropping them for
some a while with netem):
. 16774097:16775545(1448) ack 1 win 46
. 16775545:16776993(1448) ack 1 win 46
. ack 16759617 win 2399
P 16776993:16777217(224) ack 1 win 46
. ack 16762513 win 2399
. ack 16765409 win 2399
. ack 16768305 win 2399
. ack 16771201 win 2399
. ack 16774097 win 2399
. ack 16776993 win 2399
. ack 16777217 win 2399
P 16777217:16777257(40) ack 1 win 46
. ack 16777257 win 2399
P 16777257:16778705(1448) ack 1 win 46
P 16778705:16780153(1448) ack 1 win 46
FP 16780153:16781313(1160) ack 1 win 46
. ack 16778705 win 2399
. ack 16780153 win 2399
F 1:1(0) ack 16781314 win 2399
While without drop-all period I get this:
. 16773585:16775033(1448) ack 1 win 46
. ack 16764897 win 9367
. ack 16767793 win 9367
. ack 16770689 win 9367
. ack 16773585 win 9367
. 16775033:16776481(1448) ack 1 win 46
P 16776481:16777217(736) ack 1 win 46
. ack 16776481 win 9367
. ack 16777217 win 9367
P 16777217:16777218(1) ack 1 win 46
P 16777218:16777219(1) ack 1 win 46
P 16777219:16777220(1) ack 1 win 46
...
P 16777247:16777248(1) ack 1 win 46
. ack 16777218 win 9367
. ack 16777219 win 9367
...
. ack 16777233 win 9367
. ack 16777248 win 9367
P 16777248:16778696(1448) ack 1 win 46
P 16778696:16780144(1448) ack 1 win 46
FP 16780144:16781313(1169) ack 1 win 46
. ack 16780144 win 9367
F 1:1(0) ack 16781314 win 9367
The window seems to be 30-40 segments, which were successfully
combined into: P 16777217:16777257(40) ack 1 win 46
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can reduce pressure on dst entry refcount that slowdown UDP transmit
path on SMP machines. This pressure is visible on RTP servers when
delivering content to mediagateways, especially big ones, handling
thousand of streams. Several cpus send UDP frames to the same
destination, hence use the same dst entry.
This patch makes ip_push_pending_frames() steal the refcount its
callers had to take when filling inet->cork.dst.
This doesnt avoid all refcounting, but still gives speedups on SMP,
on UDP/RAW transmit path.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As GRE tries to call the update_pmtu function on skb->dst and
bridge supplies an skb->dst that has a NULL ops field, all is
not well.
This patch fixes this by giving the bridge device an ops field
with an update_pmtu function. For the moment I've left all
other fields blank but we can fill them in later should the
need arise.
Based on report and patch by Philip Craig.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conntrack creation through ctnetlink has two races:
- the timer may expire and free the conntrack concurrently, causing an
invalid memory access when attempting to put it in the hash tables
- an identical conntrack entry may be created in the packet processing
path in the time between the lookup and hash insertion
Hold the conntrack lock between the lookup and insertion to avoid this.
Reported-by: Zoltan Borbely <bozo@andrews.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can reduce pressure on dst entry refcount that slowdown UDP transmit
path on SMP machines. This pressure is visible on RTP servers when
delivering content to mediagateways, especially big ones, handling
thousand of streams. Several cpus send UDP frames to the same
destination, hence use the same dst entry.
This patch makes ip_append_data() eventually steal the refcount its
callers had to take on the dst entry.
This doesnt avoid all refcounting, but still gives speedups on SMP,
on UDP/RAW transmit path
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gen_kill_estimator() linear lists lookups are very slow, and e.g. while
deleting a large number of HTB classes soft lockups were reported. Here
is another try to fix this problem: this time internally, with rbtree,
so similarly to Jamal's hashing idea IIRC. (Looking for next hits could
be still optimized, but it's really fast as it is.)
Reported-by: Badalian Vyacheslav <slavon@bigtelecom.ru>
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski points out:
If all child qdiscs of sch_drr are non-work-conserving (e.g. sch_tbf)
drr_dequeue() will busy-loop waiting for skbs instead of leaving the
job for a watchdog. Checking for list_empty() in each loop isn't
necessary either, because this can never be true except the first time.
Using non-work-conserving qdiscs as children of DRR makes no sense,
simply bail out in that case.
Reported-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is still a call to sock_prot_inuse_add() in af_netlink
while in a preemptable section. Add explicit BH disable around
this call.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message triggers when sending non-FTP data on port 21 or with
certain clients that use multiple syscalls to send the command.
Change to pr_debug() since users have been complaining.
Signed-off-by: Patrick McHardy <kaber@trash.net>
The svc_addsock function adds transport instances without taking a
reference on the sunrpc.ko module, however, the generic transport
destruction code drops a reference when a transport instance
is destroyed.
Add a try_module_get call to the svc_addsock function for transport
instances added by this function.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Tested-by: Jeff Moyer <jmoyer@redhat.com>
net/netfilter/nf_conntrack_proto_sctp.c: In function 'sctp_packet':
net/netfilter/nf_conntrack_proto_sctp.c:376: warning: array subscript is above array bounds
gcc doesn't realize that do_basic_checks() guarantees that there is
at least one valid chunk and thus new_state is never SCTP_CONNTRACK_MAX
after the loop. Initialize to SCTP_CONNTRACK_NONE to avoid the warning.
Based on patch by Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The rule of calling sock_prot_inuse_add() is that BHs must
be disabled. Some new calls were added where this was not
true and this tiggers warnings as reported by Ilpo.
Fix this by adding explicit BH disabling around those call sites,
or moving sock_prot_inuse_add() call inside an existing BH disabled
section.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus mentioned we could try to perform long word operations, even
on potentially unaligned addresses, on x86 at least. David mentioned
the HAVE_EFFICIENT_UNALIGNED_ACCESS test to handle this on all
arches that have efficient unailgned accesses.
I tried this idea and got nice assembly on 32 bits:
158: 33 82 38 01 00 00 xor 0x138(%edx),%eax
15e: 33 8a 34 01 00 00 xor 0x134(%edx),%ecx
164: c1 e0 10 shl $0x10,%eax
167: 09 c1 or %eax,%ecx
169: 74 0b je 176 <eth_type_trans+0x87>
And very nice assembly on 64 bits of course (one xor, one shl)
Nice oprofile improvement in eth_type_trans(), 0.17 % instead of 0.41 %,
expected since we remove 8 instructions on a fast path.
This patch implements a compare_ether_addr_64bits() function, that
uses the CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS ifdef to efficiently
perform the 6 bytes comparison on all capable arches.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rule of calling sock_prot_inuse_add() is that BHs must
be disabled. Some new calls were added where this was not
true and this tiggers warnings as reported by Ilpo.
Fix this by adding explicit BH disabling around those call sites.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the last step to be able to perform full RCU lookups
in __inet_lookup() : After established/timewait tables, we
add RCU lookups to listening hash table.
The only trick here is that a socket of a given type (TCP ipv4,
TCP ipv6, ...) can now flight between two different tables
(established and listening) during a RCU grace period, so we
must use different 'nulls' end-of-chain values for two tables.
We define a large value :
#define LISTENING_NULLS_BASE (1U << 29)
So that slots in listening table are guaranteed to have different
end-of-chain values than slots in established table. A reader can
still detect it finished its lookup in the right chain.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch extends existing code:
* Confirm options divide into the confirmed value plus an optional preference
list for SP values. Previously only the preference list was echoed for SP
values, now the confirmed value is added as per RFC 4340, 6.1;
* length and sanity checks are added to avoid illegal memory (or NULL) access.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for Mandatory options is provided by this patch, which will
be used by subsequent feature-negotiation patches.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extends the scope of two available functions,
encode|decode_value_var, to work up to 6 (8) bytes, to match maximum
requirements in the RFC.
These functions are going to be used both by general option processing
and feature negotiation code, hence declarations have been put into
feat.h.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides function to query the current TX/RX CCID dynamically,
without reliance on the minisock value, using dynamic information
available in the currently loaded CCID module.
This query function is then used to
(a) provide the getsockopt part for getting/setting CCIDs via sockopts;
(b) replace the current test for "which CCID is in use" in probe.c.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, TX/RX CCIDs can now be changed on a per-connection
basis, which overrides the defaults set by the global sysctl variables
for TX/RX CCIDs.
To make full use of this facility, the remaining patches of this patch
set are needed, which track dependencies and activate negotiated
feature values.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to have relevant information for NETLINK protocol, in
/proc/net/protocols, we should use sock_prot_inuse_add() to
update a (percpu and pernamespace) counter of inuse sockets.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Use eq_net() in inet_netns_ok() to speedup socket creation if
!CONFIG_NET_NS
2) Reorder the tests about inet_ehash_secret generation (once only)
Use the unlikely() macro when testing if inet_ehash_secret already
generated.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove redundant argument comments in files of net/*
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the slub allocator is used, kmem_cache_create() may merge two or more
kmem_cache's into one but the cache name pointer is not updated and
kmem_cache_name() is no longer guaranteed to return the pointer passed
to the former function. This patch stores the kmalloc'ed pointers in the
corresponding request_sock_ops and timewait_sock_ops structures.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=12014
Since most (if not all) implementations of TSO and even the in-kernel
software GSO do not update the urgent pointer when splitting a large
segment, it is necessary to turn off TSO/GSO for all outgoing traffic
with the URG pointer set.
Looking at tcp_current_mss (and the preceding comment) I even think
this was the original intention. However, this approach is insufficient,
because TSO/GSO is turned off only for newly created frames, not for
frames which were already pending at the arrival of a message with
MSG_OOB set. These frames were created when TSO/GSO was enabled,
so they may be large, and they will have the urgent pointer set
in tcp_transmit_skb().
With this patch, such large packets will be fragmented again before
going to the transmit routine.
As a side note, at least the following NICs are known to screw up
the urgent pointer in the TCP header when doing TSO:
Intel 82566MM (PCI ID 8086:1049)
Intel 82566DC (PCI ID 8086:104b)
Intel 82541GI (PCI ID 8086:1076)
Broadcom NetXtreme II BCM5708 (PCI ID 14e4:164c)
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove converting the MAC address to a string by a direct byte
conversion and use %pM instead, since the code is now boilerplate
use a macro to define the show functions, and also use the shorter
__ATTR_RO macro to define the attributes.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old ieee80211 code only remains as a support library for the ipw2100
and ipw2200 drivers. So, move the code and rename it appropriately to
reflects it's true purpose and status.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These bits are shared already between ipw2x00 and hostap, and could
probably be shared both more cleanly and with other drivers. This
commit simply relocates the code to lib80211 and adjusts the drivers
appropriately.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes unnecessary #include <linux/netdevice.h> from
/net/mac80211/mlme.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch eliminates sparse warnings in pid rate scale algorithm
'debugfs: allow access to signed values' patch hit the dead end
year ago w/o much echo so I guess there is no real need to address this
properly.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete kernel-doc struct descriptions for fields that don't exist:
Warning(include/net/mac80211.h:1263): Excess struct/union/enum/typedef member 'conf_ht' description in 'ieee80211_ops'
Warning(net/mac80211/sta_info.h:309): Excess struct/union/enum/typedef member 'addr' description in 'sta_info'
Warning(net/mac80211/sta_info.h:309): Excess struct/union/enum/typedef member 'aid' description in 'sta_info'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Johannes Berg <johannes@sipsolutions.net>
cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh interfaces are currently opened with the FIF_ALLMULTI rx filter flag set,
however there is no BSSID in mesh so BSSID filtering should be disabled by
setting the FIF_OTHER_BSS flag as well. Also explicitly call
ieee80211_configure_filter for mesh.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozbit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adds an interface to configure the Backward Congestion Notification
(BCN) feature. In a BCN capabale network, congestion notifications
from congested points out in the network can cause the end station
limit the rate of a given traffic flow.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a netlink interface for Data Center Bridging (DCB) to get and set
the enable state of the Priority Flow Control (PFC) feature.
Primarily, this is a way to turn off PFC in the driver while DCB
remains enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds interface for Data Center Bridging (DCB) to query (and set if
supported) the number of traffic classes currently supported by the
device for the two (DCB) features: priority groups (PG) and priority
flow control (PFC).
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds to the netlink interface for Data Center Bridging (DCB), allowing
the DCB capabilities supported by a device to be queried.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for Data Center Bridging (DCB) features in the ixgbe
driver and adds an rtnetlink interface for configuring DCB to the
kernel. The DCB feature support included are Priority Grouping (PG) -
which allows bandwidth guarantees to be allocated to groups to traffic
based on the 802.1q priority, and Priority Based Flow Control (PFC) -
which introduces a new MAC control PAUSE frame which works at
granularity of the 802.1p priority instead of the link (IEEE 802.3x).
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now TCP & DCCP use RCU lookups, we can convert ehash rwlocks to spinlocks.
/proc/net/tcp and other seq_file 'readers' can safely be converted to 'writers'.
This should speedup writers, since spin_lock()/spin_unlock()
only use one atomic operation instead of two for write_lock()/write_unlock()
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like IPV4, convert the tunnel virtual devices to use net_device_ops.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to network device ops. Needed to change to directly call
the init routine since two sides share same ops. In the process
found by inspection a device ref count leak if register_netdevice failed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the HIPPI infrastructure for use with net_device_ops.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to ethernet. Convert infrastructure and the one lone FDDI
driver (for the one lone user of that hardware??). Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to new network device ops interface.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a regression reported by Max Kellermann whereby kernel profiling
showed that his clients were spending 45% of their time in
rpcauth_lookup_credcache.
It turns out that although his processes had identical uid/gid/groups,
generic_match() was failing to detect this, because the task->group_info
pointers were not shared. This again lead to the creation of a huge number
of identical credentials at the RPC layer.
The regression is fixed by comparing the contents of task->group_info
if the actual pointers are not identical.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (23 commits)
net: fix tiny output corruption of /proc/net/snmp6
atl2: don't request irq on resume if netif running
ipv6: use seq_release_private for ip6mr.c /proc entries
pkt_sched: fix missing check for packet overrun in qdisc_dump_stab()
smc911x: Fix printf format typo in smc911x driver.
asix: Fix asix-based cards connecting to 10/100Mbs LAN.
mv643xx_eth: fix recycle check bound
mv643xx_eth: fix the order of mdiobus_{unregister, free}() calls
sh: sh_eth: Update to change of mii_bus
TPROXY: supply a struct flowi->flags argument in inet_sk_rebuild_header()
TPROXY: fill struct flowi->flags in udp_sendmsg()
net: ipg.c fix bracing on endian swapping
phylib: Fix auto-negotiation restart avoidance
net: jme.c rxdesc.flags is __le16, other missing endian swaps
phylib: fix phy name example in documentation
net: Do not fire linkwatch events until the device is registered.
phonet: fix compilation with gcc-3.4
ixgbe: fix compilation with gcc-3.4
pktgen: fix multiple queue warning
net: fix ip_mr_init() error path
...
1. Make device driver to allocate memory for netdev.
2. Convert all directly reference of netdev->priv to netdev_priv().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because "name" is static, it can be occasionally be filled with
somewhat garbage if two processes read /proc/net/snmp6.
Also, remove useless casts and "-1" -- snprintf() correctly terminates it's
output.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ip6mr.c, /proc entries /proc/net/ip6_mr_cache and /proc/net/ip6_mr_vif
are opened with seq_open_private(), thus seq_release_private() should be
used to release them.
Should fix a small memory leak.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of xchg() hasn't been necessary since 2.2.something when proper
locking was added to packet schedulers. In the case of classifiers they
mostly weren't even necessary before that since they're mainly used
to assign a NULL pointer to the filter root in the ->destroy path;
the root is destroyed immediately after that.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of xchg() hasn't been necessary since 2.2.something when proper
locking was added to packet schedulers.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add classful DRR scheduler as a more flexible replacement for SFQ.
The main difference to the algorithm described in "Efficient Fair Queueing
using Deficit Round Robin" is that this implementation doesn't drop packets
from the longest queue on overrun because its classful and limits are
handled by each individual child qdisc.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_nest_start() might return NULL, causing a NULL pointer dereference.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes sparse warnings:
net/ipv4/ip_sockglue.c:146:15: warning: incorrect type in assignment (different base types)
net/ipv4/ip_sockglue.c:146:15: expected restricted __be16 [assigned] [usertype] sin_port
net/ipv4/ip_sockglue.c:146:15: got unsigned short [unsigned] [short] [usertype] <noident>
net/ipv4/ip_sockglue.c:130:6: warning: symbol 'ip_cmsg_recv_dstaddr' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_sk_rebuild_header() does a new route lookup if the dst_entry
associated with a socket becomes stale. However inet_sk_rebuild_header()
didn't use struct flowi->flags, causing the route lookup to
fail for foreign-bound IP_TRANSPARENT sockets, causing an error
state to be set for the sockets in question.
Signed-off-by: Balazs Scheidler <bazsi@balabit.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
udp_sendmsg() didn't fill struct flowi->flags, which means that
the route lookup would fail for non-local IPs even if the
IP_TRANSPARENT sockopt was set.
This prevents sendto() to work properly for UDP sockets, whereas
bind(foreign-ip) + connect() + send() worked fine.
Signed-off-by: Balazs Scheidler <bazsi@balabit.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not needed, since creation and removal are done by name.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
SKF_AD_NLATTR allows us to find the first matching attribute in a
stream of netlink attributes from one offset to the end of the
netlink message. This is not suitable to look for a specific
matching inside a set of nested attributes.
For example, in ctnetlink messages, if we look for the CTA_V6_SRC
attribute in a message that talks about an IPv4 connection,
SKF_AD_NLATTR returns the offset of CTA_STATUS which has the same
value of CTA_V6_SRC but outside the nest. To differenciate
CTA_STATUS and CTA_V6_SRC, we would have to make assumptions on the
size of the attribute and the usual offset, resulting in horrible
BSF code.
This patch adds SKF_AD_NLATTR_NEST, which is a variant of
SKF_AD_NLATTR, that looks for an attribute inside the limits of
a nested attributes, but not further.
This patch validates that we have enough room to look for the
nested attributes - based on a suggestion from Patrick McHardy.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares RCU migration of listening_hash table for
TCP/DCCP protocols.
listening_hash table being small (32 slots per protocol), we add
a spinlock for each slot, instead of a single rwlock for whole table.
This should reduce hold time of readers, and writers concurrency.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert vlan devices and function pointers to net_device_ops.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to net_device_ops function table pointer for ioctl.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to net_device_ops function table.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ethernet devices are converted, the function pointer setup
by eth_setup() need to be done during intialization.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the network device ops get_stats call to be immutable, the handling
of the default internal network device stats block has to be changed. Add a new
helper function which replaces the old use of internal_get_stats.
Note: change return code to make it clear that the caller should not
go changing the returned statistics.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the network device internal API to move adminstrative
operations out of the network device structure and into a separate structure.
This patch involves some hackery to maintain compatablity between the
new and old model, so all 300+ drivers don't have to be changed at once.
For drivers that aren't converted yet, the netdevice_ops virt function list
still resides in the net_device structure. For old protocols, the new
net_device_ops are copied out to the old net_device pointers.
After the transistion is completed the nag message can be changed to
an WARN_ON, and the compatiablity code can be made configurable.
Some function pointers aren't moved:
* destructor can't be in net_device_ops because
it may need to be referenced after the module is unloaded.
* neighbor setup is manipulated in a couple of places that need special
consideration
* hard_start_xmit is in the fast path for transmit.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new accept4() system call. The addition of this system call
matches analogous changes in 2.6.27 (dup3(), evenfd2(), signalfd4(),
inotify_init1(), epoll_create1(), pipe2()) which added new system calls
that differed from analogous traditional system calls in adding a flags
argument that can be used to access additional functionality.
The accept4() system call is exactly the same as accept(), except that
it adds a flags bit-mask argument. Two flags are initially implemented.
(Most of the new system calls in 2.6.27 also had both of these flags.)
SOCK_CLOEXEC causes the close-on-exec (FD_CLOEXEC) flag to be enabled
for the new file descriptor returned by accept4(). This is a useful
security feature to avoid leaking information in a multithreaded
program where one thread is doing an accept() at the same time as
another thread is doing a fork() plus exec(). More details here:
http://udrepper.livejournal.com/20407.html "Secure File Descriptor Handling",
Ulrich Drepper).
The other flag is SOCK_NONBLOCK, which causes the O_NONBLOCK flag
to be enabled on the new open file description created by accept4().
(This flag is merely a convenience, saving the use of additional calls
fcntl(F_GETFL) and fcntl (F_SETFL) to achieve the same result.
Here's a test program. Works on x86-32. Should work on x86-64, but
I (mtk) don't have a system to hand to test with.
It tests accept4() with each of the four possible combinations of
SOCK_CLOEXEC and SOCK_NONBLOCK set/clear in 'flags', and verifies
that the appropriate flags are set on the file descriptor/open file
description returned by accept4().
I tested Ulrich's patch in this thread by applying against 2.6.28-rc2,
and it passes according to my test program.
/* test_accept4.c
Copyright (C) 2008, Linux Foundation, written by Michael Kerrisk
<mtk.manpages@gmail.com>
Licensed under the GNU GPLv2 or later.
*/
#define _GNU_SOURCE
#include <unistd.h>
#include <sys/syscall.h>
#include <sys/socket.h>
#include <netinet/in.h>
#include <stdlib.h>
#include <fcntl.h>
#include <stdio.h>
#include <string.h>
#define PORT_NUM 33333
#define die(msg) do { perror(msg); exit(EXIT_FAILURE); } while (0)
/**********************************************************************/
/* The following is what we need until glibc gets a wrapper for
accept4() */
/* Flags for socket(), socketpair(), accept4() */
#ifndef SOCK_CLOEXEC
#define SOCK_CLOEXEC O_CLOEXEC
#endif
#ifndef SOCK_NONBLOCK
#define SOCK_NONBLOCK O_NONBLOCK
#endif
#ifdef __x86_64__
#define SYS_accept4 288
#elif __i386__
#define USE_SOCKETCALL 1
#define SYS_ACCEPT4 18
#else
#error "Sorry -- don't know the syscall # on this architecture"
#endif
static int
accept4(int fd, struct sockaddr *sockaddr, socklen_t *addrlen, int flags)
{
printf("Calling accept4(): flags = %x", flags);
if (flags != 0) {
printf(" (");
if (flags & SOCK_CLOEXEC)
printf("SOCK_CLOEXEC");
if ((flags & SOCK_CLOEXEC) && (flags & SOCK_NONBLOCK))
printf(" ");
if (flags & SOCK_NONBLOCK)
printf("SOCK_NONBLOCK");
printf(")");
}
printf("\n");
#if USE_SOCKETCALL
long args[6];
args[0] = fd;
args[1] = (long) sockaddr;
args[2] = (long) addrlen;
args[3] = flags;
return syscall(SYS_socketcall, SYS_ACCEPT4, args);
#else
return syscall(SYS_accept4, fd, sockaddr, addrlen, flags);
#endif
}
/**********************************************************************/
static int
do_test(int lfd, struct sockaddr_in *conn_addr,
int closeonexec_flag, int nonblock_flag)
{
int connfd, acceptfd;
int fdf, flf, fdf_pass, flf_pass;
struct sockaddr_in claddr;
socklen_t addrlen;
printf("=======================================\n");
connfd = socket(AF_INET, SOCK_STREAM, 0);
if (connfd == -1)
die("socket");
if (connect(connfd, (struct sockaddr *) conn_addr,
sizeof(struct sockaddr_in)) == -1)
die("connect");
addrlen = sizeof(struct sockaddr_in);
acceptfd = accept4(lfd, (struct sockaddr *) &claddr, &addrlen,
closeonexec_flag | nonblock_flag);
if (acceptfd == -1) {
perror("accept4()");
close(connfd);
return 0;
}
fdf = fcntl(acceptfd, F_GETFD);
if (fdf == -1)
die("fcntl:F_GETFD");
fdf_pass = ((fdf & FD_CLOEXEC) != 0) ==
((closeonexec_flag & SOCK_CLOEXEC) != 0);
printf("Close-on-exec flag is %sset (%s); ",
(fdf & FD_CLOEXEC) ? "" : "not ",
fdf_pass ? "OK" : "failed");
flf = fcntl(acceptfd, F_GETFL);
if (flf == -1)
die("fcntl:F_GETFD");
flf_pass = ((flf & O_NONBLOCK) != 0) ==
((nonblock_flag & SOCK_NONBLOCK) !=0);
printf("nonblock flag is %sset (%s)\n",
(flf & O_NONBLOCK) ? "" : "not ",
flf_pass ? "OK" : "failed");
close(acceptfd);
close(connfd);
printf("Test result: %s\n", (fdf_pass && flf_pass) ? "PASS" : "FAIL");
return fdf_pass && flf_pass;
}
static int
create_listening_socket(int port_num)
{
struct sockaddr_in svaddr;
int lfd;
int optval;
memset(&svaddr, 0, sizeof(struct sockaddr_in));
svaddr.sin_family = AF_INET;
svaddr.sin_addr.s_addr = htonl(INADDR_ANY);
svaddr.sin_port = htons(port_num);
lfd = socket(AF_INET, SOCK_STREAM, 0);
if (lfd == -1)
die("socket");
optval = 1;
if (setsockopt(lfd, SOL_SOCKET, SO_REUSEADDR, &optval,
sizeof(optval)) == -1)
die("setsockopt");
if (bind(lfd, (struct sockaddr *) &svaddr,
sizeof(struct sockaddr_in)) == -1)
die("bind");
if (listen(lfd, 5) == -1)
die("listen");
return lfd;
}
int
main(int argc, char *argv[])
{
struct sockaddr_in conn_addr;
int lfd;
int port_num;
int passed;
passed = 1;
port_num = (argc > 1) ? atoi(argv[1]) : PORT_NUM;
memset(&conn_addr, 0, sizeof(struct sockaddr_in));
conn_addr.sin_family = AF_INET;
conn_addr.sin_addr.s_addr = htonl(INADDR_LOOPBACK);
conn_addr.sin_port = htons(port_num);
lfd = create_listening_socket(port_num);
if (!do_test(lfd, &conn_addr, 0, 0))
passed = 0;
if (!do_test(lfd, &conn_addr, SOCK_CLOEXEC, 0))
passed = 0;
if (!do_test(lfd, &conn_addr, 0, SOCK_NONBLOCK))
passed = 0;
if (!do_test(lfd, &conn_addr, SOCK_CLOEXEC, SOCK_NONBLOCK))
passed = 0;
close(lfd);
exit(passed ? EXIT_SUCCESS : EXIT_FAILURE);
}
[mtk.manpages@gmail.com: rewrote changelog, updated test program]
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Tested-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: <linux-api@vger.kernel.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As spotted by Joe Perches, we should use KERN_INFO in unix_sock_destructor()
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first argument to csum_partial is const void *
casts to char/u8 * are not necessary
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several device drivers try to do things like netif_carrier_off()
before register_netdev() is invoked. This is bogus, but too many
drivers do this to fix them all up in one go.
Reported-by: Folkert van Heusden <folkert@vanheusden.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converting /proc/net/protocols to be namespace aware is quite easy
and permits us to use sock_prot_inuse_get().
This provides seperate counters for each protocol. For example
we can really count TCPv6 sockets and TCPv4 sockets, while previously,
we had the same value, and this value was not namespace aware.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a preparation to namespace conversion of /proc/net/protocols
In order to have relevant information for PACKET protocols, we should use
sock_prot_inuse_add() to update a (percpu and pernamespace) counter of
inuse sockets.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] net/phonet/af_phonet.o
net/phonet/af_phonet.c: In function `pn_socket_create':
net/phonet/af_phonet.c:38: sorry, unimplemented: inlining failed in call to 'phonet_proto_put': function body not available
net/phonet/af_phonet.c:99: sorry, unimplemented: called from here
make[3]: *** [net/phonet/af_phonet.o] Error 1
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As number of TX queues in unrelated to number of CPU's we remove this test
and just make sure nxtq never gets exceeded.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to IPv6 ip6_mr_init() (fixed last week), the order of cleanup
operations in the error/exit section of ip_mr_init() is completely
inversed. It should be the other way around.
Also a del_timer() is missing in the error path.
I should have guessed last week that this same error existed in ipmr.c
too, as ip6mr.c is largely inspired by ipmr.c.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before ieee80211_notify_mac() was added, it was presented with the
use case of using it to tell mac80211 that the association may
have been lost because the firmware crashed/reset.
Since then, it has also been used by iwlwifi to (slightly) speed
up re-association after resume, a workaround around the fact that
mac80211 has no suspend/resume handling yet. It is also not used
by any other drivers, so clearly it cannot be necessary for "good
enough" suspend/resume.
Unfortunately, the callback suffers from a severe problem: It only
works for station mode. If suspend/resume happens while in IBSS or
any other mode (but station), then the callback is pointless.
Recently, it has created a number of locking issues, first because
it required rtnl locking rather than RCU due to calling sleeping
functions within the critical section, and now because it's called
by iwlwifi from the mac80211 workqueue that may not use the rtnl
because it is flushed under rtnl.
(cf. http://bugzilla.kernel.org/show_bug.cgi?id=12046)
I think, therefore, that we should take a step back, remove it
entirely for now and add the small feature it provided properly.
For suspend and resume we will need to introduce new hooks, and for
the case where the firmware was reset the driver will probably
simply just pretend it has done a suspend/resume cycle to get
mac80211 to reprogram the hardware completely, not just try to
connect to the current AP again in station mode. When doing so, we
will need to take into account locking issues and possibly defer
to schedule_work from within mac80211 for the resume operation,
while the suspend operation must be done directly.
Proper suspend/resume should also not necessarily try to reconnect
to the current AP, the time spent in suspend may have been short
enough to not be disconnected from the AP, mac80211 will detect
that the AP went out of range quickly if it did, and if the
association is lost then the AP will disassoc as soon as a data
frame is sent. We might also take into account WWOL then, and
have mac80211 program the hardware into such a mode where it is
available and requested.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
net/netfilter/nf_conntrack_core.c:46:1: warning: symbol 'nfnetlink_parse_nat_setup_hook' was not declared. Should it be static?
Including the proper header also revealed an incorrect prototype.
Signed-off-by: Patrick McHardy <kaber@trash.net>
net/netfilter/nfnetlink_log.c:537:1: warning: symbol 'nfulnl_log_packet' was not declared. Should it be static?
Including the proper header also revealed an incorrect prototype.
Signed-off-by: Patrick McHardy <kaber@trash.net>
As for now, the creation and update of conntracks via ctnetlink do not
propagate an event to userspace. This can result in inconsistent situations
if several userspace processes modify the connection tracking table by means
of ctnetlink at the same time. Specifically, using the conntrack command
line tool and conntrackd at the same time can trigger unconsistencies.
This patch also modifies the event cache infrastructure to pass the
process PID and the ECHO flag to nfnetlink_send() to report back
to userspace if the process that triggered the change needs so.
Based on a suggestion from Patrick McHardy.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch adds module loading for helpers via ctnetlink.
* Creation path: We support explicit and implicit helper assignation. For
the explicit case, we try to load the module. If the module is correctly
loaded and the helper is present, we return EAGAIN to re-start the
creation. Otherwise, we return EOPNOTSUPP.
* Update path: release the spin lock, load the module and check. If it is
present, then return EAGAIN to re-start the update.
This patch provides a refactorized function to lookup-and-set the
connection tracking helper. The function removes the exported symbol
__nf_ct_helper_find as it has not clients anymore.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch adds the macro MODULE_ALIAS_NFCT_HELPER that defines a
way to provide generic and persistent aliases for the connection
tracking helpers.
This next patch requires this patch.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch replaces the unnecessary module refcounting with
the read-side locks. With this patch, all the dump and fill_info
function are called under the RCU read lock.
Based on a patch from Fabian Hugelshofer.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch changes the return value if the conntrack has no helper assigned.
Instead of EINVAL, which is reserved for malformed messages, it returns
EOPNOTSUPP.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Use nf_conntrack_get instead of the direct call to atomic_inc.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch is a preparation to namespace conversion of /proc/net/protocols
In order to have relevant information for SCTP protocols, we should use
sock_prot_inuse_add() to update a (percpu and pernamespace) counter of
inuse sockets.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a preparation to namespace conversion of /proc/net/protocols
In order to have relevant information for UNIX protocol, we should use
sock_prot_inuse_add() to update a (percpu and pernamespace) counter of
inuse sockets.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, /proc/net/protocols displays socket counts only for TCP/TCPv6
protocols
We can provide unix_nr_socks for free here, this counter being
already maintained in af_unix
Before patch :
# grep UNIX /proc/net/protocols
UNIX 428 -1 -1 NI 0 yes kernel
After patch :
# grep UNIX /proc/net/protocols
UNIX 428 98 -1 NI 0 yes kernel
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike ifconfig, iproute doesn't report an error when setting
an interface up fails:
(example: put wireless network mac80211 interface into repeater mode
with iwconfig but do not set a peer MAC address, it should fail with
-ENOLINK)
without patch:
# ip link set wlan0 up ; echo $?
0
#
with patch:
# ip link set wlan0 up ; echo $?
RTNETLINK answers: Link has been severed
2
#
Propagate the return value from dev_change_flags() to fix this.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simply delete ops from list and let list debugging do the job.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a pure cleanup of net/unix/af_unix.c to meet current code
style standards
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This splits the setsockopt calls into two groups, depending on whether an
integer argument (val) is required and whether routines being called do
their own locking.
Some options (such as setting the CCID) use u8 rather than int, so that for
these the test with regard to integer-sizeof can not be used.
The second switch-case statement now only has those statements which need
locking and which make use of `val'.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Reviewed-by: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch deprecates the Ack Ratio sysctl, since
* Ack Ratio is entirely ignored by CCID-3 and CCID-4,
* Ack Ratio currently doesn't work in CCID-2 (i.e. is always set to 1);
* even if it would work in CCID-2, there is no point for a user to change it:
- Ack Ratio is constrained by cwnd (RFC 4341, 6.1.2),
- if Ack Ratio > cwnd, the system resorts to spurious RTO timeouts
(since waiting for Acks which will never arrive in this window),
- cwnd is not a user-configurable value.
The only reasonable place for Ack Ratio is to print it for debugging. It is
planned to do this later on, as part of e.g. dccp_probe.
With this patch Ack Ratio is now under full control of feature negotiation:
* Ack Ratio is resolved as a dependency of the selected CCID;
* if the chosen CCID supports it (i.e. CCID == CCID-2), Ack Ratio is set to
the default of 2, following RFC 4340, 11.3 - "New connections start with Ack
Ratio 2 for both endpoints";
* what happens then is part of another patch set, since it concerns the
dynamic update of Ack Ratio while the connection is in full flight.
Thanks to Tomasz Grobelny for discussion leading up to this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides feature negotiation for server minimum checksum coverage
which so far has been missing.
Since sender/receiver coverage values range only from 0...15, their
type has also been reduced in size from u16 to u4.
Feature-negotiation options are now generated for both sender and receiver
coverage, i.e. when the peer has `forgotten' to enable partial coverage
then feature negotiation will automatically enable (negotiate) the partial
coverage value for this connection.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous setsockopt interface, which passed socket options via struct
dccp_so_feat, is complicated/difficult to use. Continuing to support it leads to
ugly code since the old approach did not distinguish between NN and SP values.
This patch removes the old setsockopt interface and replaces it with two new
functions to register NN/SP values for feature negotiation.
These are essentially wrappers around the internal __feat_register functions,
with checking added to avoid
* wrong usage (type);
* changing values while the connection is in progress.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a hook to resolve features whose value depends on the choice of
CCID. It is done at the server since it can only be done after the CCID
values have been negotiated; i.e. the client will add its CCID preference
list on the Change options sent in the Request, which will be reconciled
with the local preference list of the server.
The concept is documented on
http://www.erg.abdn.ac.uk/users/gerrit/dccp/notes/feature_negotiation/\
implementation_notes.html#ccid_dependencies
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Technically, patch changes format for modules, but I think nobody cares.
-86dd :ipv6:ipv6_rcv+0x0
+86dd ipv6_rcv+0x0/0x400 [ipv6]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RCU was added to UDP lookups, using a fast infrastructure :
- sockets kmem_cache use SLAB_DESTROY_BY_RCU and dont pay the
price of call_rcu() at freeing time.
- hlist_nulls permits to use few memory barriers.
This patch uses same infrastructure for TCP/DCCP established
and timewait sockets.
Thanks to SLAB_DESTROY_BY_RCU, no slowdown for applications
using short lived TCP connections. A followup patch, converting
rwlocks to spinlocks will even speedup this case.
__inet_lookup_established() is pretty fast now we dont have to
dirty a contended cache line (read_lock/read_unlock)
Only established and timewait hashtable are converted to RCU
(bind table and listen table are still using traditional locking)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a straightforward patch, using hlist_nulls infrastructure.
RCUification already done on UDP two weeks ago.
Using hlist_nulls permits us to avoid some memory barriers, both
at lookup time and delete time.
Patch is large because it adds new macros to include/net/sock.h.
These macros will be used by TCP & DCCP in next patch.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case UDP traffic is redirected to a local UDP socket,
the originally addressed destination address/port
cannot be recovered with the in-kernel tproxy.
This patch adds an IP_RECVORIGDSTADDR sockopt that enables
a IP_ORIGDSTADDR ancillary message in recvmsg(). This
ancillary message contains the original destination address/port
of the packet being received.
Signed-off-by: Balazs Scheidler <bazsi@balabit.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Greear wrote:
> I have 500 mac-vlans on a system talking to 500 other
> mac-vlans. My problem is that the arp-table gets extremely
> huge because every time an arp-request comes in on all mac-vlans,
> a stale arp entry is added for each mac-vlan. I have filtering
> turned on, but that doesn't help because the neigh_event_ns call
> below will cause a stale neighbor entry to be created regardless
> of whether a replay will be sent or not.
> Maybe the neigh_event code should be below the checks for dont_send,
> and only create check neigh_event_ns if we are !dont_send?
The attached patch makes it work much better for me. The patch
will cause the code to NOT create a stale neighbor entry if we
are not going to respond to the ARP request. The old code
*would* create a stale entry even if we are not going to respond.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the next page of the scm recursion story (the commit
f8d570a4 net: Fix recursive descent in __scm_destroy()).
In function scm_fp_dup(), the INIT_LIST_HEAD(&fpl->list) of newly
created fpl is done *before* the subsequent memcpy from the old
structure and thus the freshly initialized list is overwritten.
But that's OK, since this initialization is not required at all,
since the fpl->list is list_add-ed at the destruction time in any
case (and is unused in other code), so I propose to drop both
initializations, rather than moving it after the memcpy.
Please, correct me if I miss something significant.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During tbench/oprofile sessions, I found that dst_release() was in third position.
CPU: Core 2, speed 2999.68 MHz (estimated)
Counted CPU_CLK_UNHALTED events (Clock cycles when not halted) with a unit mask of 0x00 (Unhalted core cycles) count 100000
samples % symbol name
483726 9.0185 __copy_user_zeroing_intel
191466 3.5697 __copy_user_intel
185475 3.4580 dst_release
175114 3.2648 ip_queue_xmit
153447 2.8608 tcp_sendmsg
108775 2.0280 tcp_recvmsg
102659 1.9140 sysenter_past_esp
101450 1.8914 tcp_current_mss
95067 1.7724 __copy_from_user_ll
86531 1.6133 tcp_transmit_skb
Of course, all CPUS fight on the dst_entry associated with 127.0.0.1
Instead of first checking the refcount value, then decrement it,
we use atomic_dec_return() to help CPU to make the right memory transaction
(ie getting the cache line in exclusive mode)
dst_release() is now at the fifth position, and tbench a litle bit faster ;)
CPU: Core 2, speed 3000.1 MHz (estimated)
Counted CPU_CLK_UNHALTED events (Clock cycles when not halted) with a unit mask of 0x00 (Unhalted core cycles) count 100000
samples % symbol name
647107 8.8072 __copy_user_zeroing_intel
258840 3.5229 ip_queue_xmit
258302 3.5155 __copy_user_intel
209629 2.8531 tcp_sendmsg
165632 2.2543 dst_release
149232 2.0311 tcp_current_mss
147821 2.0119 tcp_recvmsg
137893 1.8767 sysenter_past_esp
127473 1.7349 __copy_from_user_ll
121308 1.6510 ip_finish_output
118510 1.6129 tcp_transmit_skb
109295 1.4875 tcp_v4_rcv
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix this warning:
net/bluetooth/af_bluetooth.c:60: warning: ‘bt_key_strings’ defined but not used
net/bluetooth/af_bluetooth.c:71: warning: ‘bt_slock_key_strings’ defined but not used
this is a lockdep macro problem in the !LOCKDEP case.
We cannot convert it to an inline because the macro works on multiple types,
but we can mark the parameter used.
[ also clean up a misaligned tab in sock_lock_init_class_and_name() ]
[ also remove #ifdefs from around af_family_clock_key strings - which
were certainly added to get rid of the ugly build warnings. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
After implementing qdisc->ops->peek() and changing sch_netem into
classless qdisc there are no more qdisc->ops->requeue() users. This
patch removes this method with its wrappers (qdisc_requeue()), and
also unused qdisc->requeue structure. There are a few minor fixes of
warnings (htb_enqueue()) and comments btw.
The idea to kill ->requeue() and a similar patch were first developed
by David S. Miller.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
security/keys/internal.h
security/keys/process_keys.c
security/keys/request_key.c
Fixed conflicts above by using the non 'tsk' versions.
Signed-off-by: James Morris <jmorris@namei.org>
Attach creds to file structs and discard f_uid/f_gid.
file_operations::open() methods (such as hppfs_open()) should use file->f_cred
rather than current_cred(). At the moment file->f_cred will be current_cred()
at this point.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Signed-off-by: James Morris <jmorris@namei.org>
Inaugurate copy-on-write credentials management. This uses RCU to manage the
credentials pointer in the task_struct with respect to accesses by other tasks.
A process may only modify its own credentials, and so does not need locking to
access or modify its own credentials.
A mutex (cred_replace_mutex) is added to the task_struct to control the effect
of PTRACE_ATTACHED on credential calculations, particularly with respect to
execve().
With this patch, the contents of an active credentials struct may not be
changed directly; rather a new set of credentials must be prepared, modified
and committed using something like the following sequence of events:
struct cred *new = prepare_creds();
int ret = blah(new);
if (ret < 0) {
abort_creds(new);
return ret;
}
return commit_creds(new);
There are some exceptions to this rule: the keyrings pointed to by the active
credentials may be instantiated - keyrings violate the COW rule as managing
COW keyrings is tricky, given that it is possible for a task to directly alter
the keys in a keyring in use by another task.
To help enforce this, various pointers to sets of credentials, such as those in
the task_struct, are declared const. The purpose of this is compile-time
discouragement of altering credentials through those pointers. Once a set of
credentials has been made public through one of these pointers, it may not be
modified, except under special circumstances:
(1) Its reference count may incremented and decremented.
(2) The keyrings to which it points may be modified, but not replaced.
The only safe way to modify anything else is to create a replacement and commit
using the functions described in Documentation/credentials.txt (which will be
added by a later patch).
This patch and the preceding patches have been tested with the LTP SELinux
testsuite.
This patch makes several logical sets of alteration:
(1) execve().
This now prepares and commits credentials in various places in the
security code rather than altering the current creds directly.
(2) Temporary credential overrides.
do_coredump() and sys_faccessat() now prepare their own credentials and
temporarily override the ones currently on the acting thread, whilst
preventing interference from other threads by holding cred_replace_mutex
on the thread being dumped.
This will be replaced in a future patch by something that hands down the
credentials directly to the functions being called, rather than altering
the task's objective credentials.
(3) LSM interface.
A number of functions have been changed, added or removed:
(*) security_capset_check(), ->capset_check()
(*) security_capset_set(), ->capset_set()
Removed in favour of security_capset().
(*) security_capset(), ->capset()
New. This is passed a pointer to the new creds, a pointer to the old
creds and the proposed capability sets. It should fill in the new
creds or return an error. All pointers, barring the pointer to the
new creds, are now const.
(*) security_bprm_apply_creds(), ->bprm_apply_creds()
Changed; now returns a value, which will cause the process to be
killed if it's an error.
(*) security_task_alloc(), ->task_alloc_security()
Removed in favour of security_prepare_creds().
(*) security_cred_free(), ->cred_free()
New. Free security data attached to cred->security.
(*) security_prepare_creds(), ->cred_prepare()
New. Duplicate any security data attached to cred->security.
(*) security_commit_creds(), ->cred_commit()
New. Apply any security effects for the upcoming installation of new
security by commit_creds().
(*) security_task_post_setuid(), ->task_post_setuid()
Removed in favour of security_task_fix_setuid().
(*) security_task_fix_setuid(), ->task_fix_setuid()
Fix up the proposed new credentials for setuid(). This is used by
cap_set_fix_setuid() to implicitly adjust capabilities in line with
setuid() changes. Changes are made to the new credentials, rather
than the task itself as in security_task_post_setuid().
(*) security_task_reparent_to_init(), ->task_reparent_to_init()
Removed. Instead the task being reparented to init is referred
directly to init's credentials.
NOTE! This results in the loss of some state: SELinux's osid no
longer records the sid of the thread that forked it.
(*) security_key_alloc(), ->key_alloc()
(*) security_key_permission(), ->key_permission()
Changed. These now take cred pointers rather than task pointers to
refer to the security context.
(4) sys_capset().
This has been simplified and uses less locking. The LSM functions it
calls have been merged.
(5) reparent_to_kthreadd().
This gives the current thread the same credentials as init by simply using
commit_thread() to point that way.
(6) __sigqueue_alloc() and switch_uid()
__sigqueue_alloc() can't stop the target task from changing its creds
beneath it, so this function gets a reference to the currently applicable
user_struct which it then passes into the sigqueue struct it returns if
successful.
switch_uid() is now called from commit_creds(), and possibly should be
folded into that. commit_creds() should take care of protecting
__sigqueue_alloc().
(7) [sg]et[ug]id() and co and [sg]et_current_groups.
The set functions now all use prepare_creds(), commit_creds() and
abort_creds() to build and check a new set of credentials before applying
it.
security_task_set[ug]id() is called inside the prepared section. This
guarantees that nothing else will affect the creds until we've finished.
The calling of set_dumpable() has been moved into commit_creds().
Much of the functionality of set_user() has been moved into
commit_creds().
The get functions all simply access the data directly.
(8) security_task_prctl() and cap_task_prctl().
security_task_prctl() has been modified to return -ENOSYS if it doesn't
want to handle a function, or otherwise return the return value directly
rather than through an argument.
Additionally, cap_task_prctl() now prepares a new set of credentials, even
if it doesn't end up using it.
(9) Keyrings.
A number of changes have been made to the keyrings code:
(a) switch_uid_keyring(), copy_keys(), exit_keys() and suid_keys() have
all been dropped and built in to the credentials functions directly.
They may want separating out again later.
(b) key_alloc() and search_process_keyrings() now take a cred pointer
rather than a task pointer to specify the security context.
(c) copy_creds() gives a new thread within the same thread group a new
thread keyring if its parent had one, otherwise it discards the thread
keyring.
(d) The authorisation key now points directly to the credentials to extend
the search into rather pointing to the task that carries them.
(e) Installing thread, process or session keyrings causes a new set of
credentials to be created, even though it's not strictly necessary for
process or session keyrings (they're shared).
(10) Usermode helper.
The usermode helper code now carries a cred struct pointer in its
subprocess_info struct instead of a new session keyring pointer. This set
of credentials is derived from init_cred and installed on the new process
after it has been cloned.
call_usermodehelper_setup() allocates the new credentials and
call_usermodehelper_freeinfo() discards them if they haven't been used. A
special cred function (prepare_usermodeinfo_creds()) is provided
specifically for call_usermodehelper_setup() to call.
call_usermodehelper_setkeys() adjusts the credentials to sport the
supplied keyring as the new session keyring.
(11) SELinux.
SELinux has a number of changes, in addition to those to support the LSM
interface changes mentioned above:
(a) selinux_setprocattr() no longer does its check for whether the
current ptracer can access processes with the new SID inside the lock
that covers getting the ptracer's SID. Whilst this lock ensures that
the check is done with the ptracer pinned, the result is only valid
until the lock is released, so there's no point doing it inside the
lock.
(12) is_single_threaded().
This function has been extracted from selinux_setprocattr() and put into
a file of its own in the lib/ directory as join_session_keyring() now
wants to use it too.
The code in SELinux just checked to see whether a task shared mm_structs
with other tasks (CLONE_VM), but that isn't good enough. We really want
to know if they're part of the same thread group (CLONE_THREAD).
(13) nfsd.
The NFS server daemon now has to use the COW credentials to set the
credentials it is going to use. It really needs to pass the credentials
down to the functions it calls, but it can't do that until other patches
in this series have been applied.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: James Morris <jmorris@namei.org>
Wrap current->cred and a few other accessors to hide their actual
implementation.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Separate the task security context from task_struct. At this point, the
security data is temporarily embedded in the task_struct with two pointers
pointing to it.
Note that the Alpha arch is altered as it refers to (E)UID and (E)GID in
entry.S via asm-offsets.
With comment fixes Signed-off-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: netdev@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: netdev@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: J. Bruce Fields <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: linux-nfs@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: netdev@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Reviewed-by: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Cc: v9fs-developer@lists.sourceforge.net
Signed-off-by: James Morris <jmorris@namei.org>
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.
This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make 9p's RDMA option depend on INET since it uses Infiniband rdma_*
functions and that code depends on INET. Otherwise 9p can try to
use symbols which don't exist.
ERROR: "rdma_destroy_id" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_connect" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_create_id" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_create_qp" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_resolve_route" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_disconnect" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_resolve_addr" [net/9p/9pnet_rdma.ko] undefined!
I used an if/endif block so that the menu items would remain
presented together.
Also correct an article adjective.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 2518c7c2b3 ("[XFRM]: Hash
policies when non-prefixed."), the last use of xfrm_gen_policy() first
argument was removed, but the argument was left behind in the
prototype.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failure to pass netns_ok check is SILENT, except some MIB counter is
incremented somewhere.
And adding "netns_ok = 1" (after long head-scratching session) is
usually the last step in making some protocol netns-ready...
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two bugs:
1. setsockopt() of anything but a Type 2 routing header should return
EINVAL instead of EPERM. Noticed by Shan Wei
(shanwei@cn.fujitsu.com).
2. setsockopt()/sendmsg() of a Type 2 routing header with invalid
length or segments should return EINVAL. These values are statically
fixed in RFC 3775, unlike the variable Type 0 was.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ieee80211_notify_mac() function uses ieee80211_sta_req_auth() which
in turn calls ieee80211_set_disassoc() which calls a few functions that
need to be able to sleep, so ieee80211_notify_mac() cannot use RCU
locking for the interface list and must use rtnl locking instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In __sock_recv_timestamp() the additional SCM_TIMESTAMP[NS] is used. This
has the same value as SO_TIMESTAMP[NS], so this is a purely cosmetic change.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a minor bug in tcp_htcp.c which has been
highlighted by Lachlan Andrew and Lawrence Stewart. Currently, the
time since the last congestion event, which is stored in variable
last_cong, is reset whenever there is a state change into
TCP_CA_Open. This includes transitions of the type
TCP_CA_Open->TCP_CA_Disorder->TCP_CA_Open which are not associated
with backoff of cwnd. The patch changes last_cong to be updated
only on transitions into TCP_CA_Open that occur after experiencing
the congestion-related states TCP_CA_Loss, TCP_CA_Recovery,
TCP_CA_CWR.
Signed-off-by: Doug Leith <doug.leith@nuim.ie>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using read_pnet() and write_pnet() in neighbour code ease the reading
of code.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can shrink size of "struct inet_bind_bucket" by 50%, using
read_pnet() and write_pnet()
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides a missing link in the code chain, as several features implicitly
depend and/or rely on the choice of CCID. Most notably, this is the Send Ack Vector
feature, but also Ack Ratio and Send Loss Event Rate (also taken care of).
For Send Ack Vector, the situation is as follows:
* since CCID2 mandates the use of Ack Vectors, there is no point in allowing
endpoints which use CCID2 to disable Ack Vector features such a connection;
* a peer with a TX CCID of CCID2 will always expect Ack Vectors, and a peer
with a RX CCID of CCID2 must always send Ack Vectors (RFC 4341, sec. 4);
* for all other CCIDs, the use of (Send) Ack Vector is optional and thus
negotiable. However, this implies that the code negotiating the use of Ack
Vectors also supports it (i.e. is able to supply and to either parse or
ignore received Ack Vectors). Since this is not the case (CCID-3 has no Ack
Vector support), the use of Ack Vectors is here disabled, with a comment
in the source code.
An analogous consideration arises for the Send Loss Event Rate feature,
since the CCID-3 implementation does not support the loss interval options
of RFC 4342. To make such use explicit, corresponding feature-negotiation
options are inserted which signal the use of the loss event rate option,
as it is used by the CCID3 code.
Lastly, the values of the Ack Ratio feature are matched to the choice of CCID.
The patch implements this as a function which is called after the user has
made all other registrations for changing default values of features.
The table is variable-length, the reserved (and hence for feature-negotiation
invalid, confirmed by considering section 19.4 of RFC 4340) feature number `0'
is used to mark the end of the table.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides a data structure to record which CCIDs are locally supported
and three accessor functions:
- a test function for internal use which is used to validate CCID requests
made by the user;
- a copy function so that the list can be used for feature-negotiation;
- documented getsockopt() support so that the user can query capabilities.
The data structure is a table which is filled in at compile-time with the
list of available CCIDs (which in turn depends on the Kconfig choices).
Using the copy function for cloning the list of supported CCIDs is useful for
feature negotiation, since the negotiation is now with the full list of available
CCIDs (e.g. {2, 3}) instead of the default value {2}. This means negotiation
will not fail if the peer requests to use CCID3 instead of CCID2.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two registration routines, for SP and NN features, are provided by this patch,
replacing a previous routine which was used for both feature types.
These are internal-only routines and therefore start with `__feat_register'.
It further exports the known limits of Sequence Window and Ack Ratio as symbolic
constants.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch limits feature (capability) negotation to the connection setup phase:
1. Although it is theoretically possible to perform feature negotiation at any
time (and RFC 4340 supports this), in practice this is prohibitively complex,
as it requires to put traffic on hold for each new negotiation.
2. As a byproduct of restricting feature negotiation to connection setup, the
feature-negotiation retransmit timer is no longer required. This part is now
mapped onto the protocol-level retransmission.
Details indicating why timers are no longer needed can be found on
http://www.erg.abdn.ac.uk/users/gerrit/dccp/notes/feature_negotiation/\
implementation_notes.html
This patch disables anytime negotiation, subsequent patches work out full
feature negotiation support for connection setup.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
->pde isn't actually needed, since name is stashed in ->id.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
dsa: fix master interface allmulti/promisc handling
dsa: fix skb->pkt_type when mac address of slave interface differs
net: fix setting of skb->tail in skb_recycle_check()
net: fix /proc/net/snmp as memory corruptor
mac80211: fix a buffer overrun in station debug code
netfilter: payload_len is be16, add size of struct rather than size of pointer
ipv6: fix ip6_mr_init error path
[4/4] dca: fixup initialization dependency
[3/4] I/OAT: fix async_tx.callback checking
[2/4] I/OAT: fix dma_pin_iovec_pages() error handling
[1/4] I/OAT: fix channel resources free for not allocated channels
ssb: Fix DMA-API compilation for non-PCI systems
SSB: hide empty sub menu
vlan: Fix typos in proc output string
[netdrvr] usb/hso: Cleanup rfkill error handling
sfc: Correct address of gPXE boot configuration in EEPROM
el3_common_init() should be __devinit, not __init
hso: rfkill type should be WWAN
mlx4_en: Start port error flow bug fix
af_key: mark policy as dead before destroying
Before commit b6c40d68ff ("net: only
invoke dev->change_rx_flags when device is UP"), the dsa driver could
sort-of get away with only fiddling with the master interface's
allmulti/promisc counts in ->change_rx_flags() and not touching them
in ->open() or ->stop(). After this commit (note that it was merged
almost simultaneously with the dsa patches, which is why this wasn't
caught initially), the breakage that was already there became more
apparent.
Since it makes no sense to keep the master interface's allmulti or
promisc count pinned for a slave interface that is down, copy the vlan
driver's sync logic (which does exactly what we want) over to dsa to
fix this.
Bug report from Dirk Teurlings <dirk@upexia.nl> and Peter van Valderen
<linux@ddcrew.com>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a dsa slave interface has a mac address that differs from that
of the master interface, eth_type_trans() won't explicitly set
skb->pkt_type back to PACKET_HOST -- we need to do this ourselves
before calling eth_type_trans().
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since skb_reset_tail_pointer() reads skb->data, we need to set
skb->data before calling skb_reset_tail_pointer(). This was causing
spurious skb_over_panic()s from skb_put() being called on a recycled
skb that had its skb->tail set to beyond where it should have been.
Bug report from Peter van Valderen <linux@ddcrew.com>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
icmpmsg_put() can happily corrupt kernel memory, using a static
table and forgetting to reset an array index in a loop.
Remove the static array since its not safe without proper locking.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mac80211/debugfs_sta.c
The trailing zero was written to state[4], it's out of bounds.
Signed-off-by: Jianjun Kong <jianjun@zeuux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing pktgen, I found that sometimes my configurations from
previous runs would be left over, particularly when going from a test
with 8 threads down to a test with 4 threads.
This adds new functionality to pktgen where you can call
pgset "reset"
and it will be just like you just insmod'ed pktgen again.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
payload_len is a be16 value, not cpu_endian, also the size of a ponter
to a struct ipv6hdr was being added, not the size of the struct itself.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order of cleanup operations in the error/exit section of ip6_mr_init()
is completely inversed. It should be the other way around.
Also a del_timer() is missing in the error path.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As regulatory_request gets bigger there will be more questions
of what things means, so clarify documenation for it and
keep track of the special alpha2 codes we use internally
and on the userspace regulatory agents.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are certain scenerios where we require intersecting
two regulatory domains. This adds intersection support.
When we enable 802.11d support we will use this to intersect
the regulatory domain from the AP's country IE and what our
regulatory agent believes is correct for a country.
This patch enables intersection for now in the case where
the last regdomain was set by a country IE which was parsed
and the user then wants to set the regulatory domain. Since
we don't support country IE parsing yet this code path will not
be hit, however this allows us to pave the way for 11d support.
Intersection code has been tested in userspace with CRDA.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A regulatory rule is invalid when the frequency difference
between the end of the frequency range and the start is 0.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the addition of basic rate set and TX queue parameter
configuration and confirmation that power save buffering is
working again, mac80211 is now in state that allows AP mode to be
used without major problems. Consequently, it is time to allow this
mode to be enabled without having to patch the kernel.
AP mode requires hostapd for management frame processing and as such,
configuring this mode is only allowed through cfg80211 (not with
iwconfig and WEXT).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In previous code all the rates were marked as basic.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new attribute, NL80211_ATTR_WIPHY_TXQ_PARAMS, that can be used with
NL80211_CMD_SET_WIPHY for userspace (e.g., hostapd) to set TX queue
parameters (txop, cwmin, cwmax, aifs).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new attribute, NL80211_ATTR_BSS_BASIC_RATES, that can be used with
NL80211_CMD_SET_BSS for userspace (e.g., hostapd) to set which rates are
in the basic rate set.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a helper function that, given a bitmap of basic
rates and a bitrate returns the response rate for this rate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes two current compilation problems. They showed up
with CONFIG_IEEE80211_DEBUG defined.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send a notification to the driver on succesful
reception of an ADDBA response, add IEEE80211_AMPDU_TX_RESUME
for this purpose.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the SSID from the driver API since now there is no
driver that requires knowing the SSID and I think it's
unlikely that any hardware design that does require the
SSID will play well with mac80211.
This also removes support for setting the SSID in master
mode which will require a patch to hostapd to not try.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a constant from the 802.11 specification.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch prints reason code for deauth/dissoc frames to give users
more ideas what's happened for the disconnection.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously I assumed that the receive queues of candidates don't
change during the GC. This is only half true, nothing can be received
from the queues (see comment in unix_gc()), but buffers could be added
through the other half of the socket pair, which may still have file
descriptors referring to it.
This can result in inc_inflight_move_tail() erronously increasing the
"inflight" counter for a unix socket for which dec_inflight() wasn't
previously called. This in turn can trigger the "BUG_ON(total_refs <
inflight_refs)" in a later garbage collection run.
Fix this by only manipulating the "inflight" counter for sockets which
are candidates themselves. Duplicating the file references in
unix_attach_fds() is also needed to prevent a socket becoming a
candidate for GC while the skb that contains it is not yet queued.
Reported-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use htonl rather than ntohl on a u32.
net/tipc/name_table.c:557:2: warning: cast to restricted __be32
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The classifier should cover the most common use case and will work
without any special configuration.
The principle of the classifier is to directly access the
task_struct via get_current(). In order for this to work,
classification requests from softirqs must be ignored. This is
not a problem because the vast majority of packets in softirq
context are not assigned to a task anyway. For this to work, a
mechanism is needed to trace softirq context.
This repost goes back to the method of relying on the number of
nested bh disable calls for the sake of not adding too much
complexity and the option to come up with something more reliable
if actually needed.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was recently hunting a bug that occurred in network namespace
cleanup. In looking at the code it became apparrent that we have
and will continue to have cases where if we have anything going
on in a network namespace there will be assumptions that the
loopback device is present. Things like sending igmp unsubscribe
messages when we bring down network devices invokes the routing
code which assumes that at least the loopback driver is present.
Therefore to avoid magic initcall ordering hackery that is hard
to follow and hard to get right insert a call to register the
loopback device directly from net_dev_init(). This guarantes
that the loopback device is the first device registered and
the last network device to go away.
But do it carefully so we register the loopback device after
we clear dev_boot_phase.
Signed-off-by: Eric W. Biederman <ebiederm@maxwell.aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to setup the network namespace state before we register
the notifier. Otherwise if a network device is already registered
we get a nasty NULL pointer dereference.
Signed-off-by: Eric W. Biederman <ebiederm@maxwell.aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/phonet/af_phonet.c:38:36: error: marked inline, but without a definition
net/phonet/pep-gprs.c:63:10: warning: incorrect type in return expression (different base types)
net/phonet/pep-gprs.c:63:10: expected int
net/phonet/pep-gprs.c:63:10: got restricted __be16 [usertype] <noident>
net/phonet/pep-gprs.c:65:10: warning: incorrect type in return expression (different base types)
net/phonet/pep-gprs.c:65:10: expected int
net/phonet/pep-gprs.c:65:10: got restricted __be16 [usertype] <noident>
net/phonet/pep-gprs.c:124:16: warning: incorrect type in assignment (different base types)
net/phonet/pep-gprs.c:124:16: expected restricted __be16 [usertype] protocol
net/phonet/pep-gprs.c:124:16: got unsigned short [unsigned] [usertype] protocol
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm_policy_destroy() will oops if not dead policy is passed to it.
On error path in pfkey_compile_policy() exactly this happens.
Oopsable for CAP_NET_ADMIN owners.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's called from __init code only. And__devinit in generic networking code
is pretty strange :^)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Fix recursive descent in __scm_destroy().
iwl3945: fix deadlock on suspend
iwl3945: do not send scan command if channel count zero
iwl3945: clear scanning bits upon failure
ath5k: correct handling of rx status fields
zd1211rw: Add 2 device IDs
Fix logic error in rfkill_check_duplicity
iwlagn: avoid sleep in softirq context
iwlwifi: clear scanning bits upon failure
Revert "ath5k: honor FIF_BCN_PRBRESP_PROMISC in STA mode"
tcp: Fix recvmsg MSG_PEEK influence of blocking behavior.
netfilter: netns ct: walk netns list under RTNL
ipv6: fix run pending DAD when interface becomes ready
net/9p: fix printk format warnings
net: fix packet socket delivery in rx irq handler
xfrm: Have af-specific init_tempsel() initialize family field of temporary selector
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
net/9p: fix printk format warnings
unsigned fid->fid cannot be negative
9p: rdma: remove duplicated #include
p9: Fix leak of waitqueue in request allocation path
9p: Remove unneeded free of fcall for Flush
9p: Make all client spin locks IRQ safe
9p: rdma: Set trans prior to requesting async connection ops
__scm_destroy() walks the list of file descriptors in the scm_fp_list
pointed to by the scm_cookie argument.
Those, in turn, can close sockets and invoke __scm_destroy() again.
There is nothing which limits how deeply this can occur.
The idea for how to fix this is from Linus. Basically, we do all of
the fput()s at the top level by collecting all of the scm_fp_list
objects hit by an fput(). Inside of the initial __scm_destroy() we
keep running the list until it is empty.
Signed-off-by: David S. Miller <davem@davemloft.net>
__scm_destroy() walks the list of file descriptors in the scm_fp_list
pointed to by the scm_cookie argument.
Those, in turn, can close sockets and invoke __scm_destroy() again.
There is nothing which limits how deeply this can occur.
The idea for how to fix this is from Linus. Basically, we do all of
the fput()s at the top level by collecting all of the scm_fp_list
objects hit by an fput(). Inside of the initial __scm_destroy() we
keep running the list until it is empty.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
> I'll have a prod at why the [hso] rfkill stuff isn't working next
Ok, I believe this is due to the addition of rfkill_check_duplicity in
rfkill and the fact that test_bit actually returns a negative value
rather than the postive one expected (which is of course equally true).
So when the second WLAN device (the hso device, with the EEE PC WLAN
being the first) comes along rfkill_check_duplicity returns a negative
value and so rfkill_register returns an error. Patch below fixes this
for me.
Signed-Off-By: Jonathan McDowell <noodles@earth.li>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds better IPv6 failover support for bonding devices,
especially when in active-backup mode and there are only IPv6 addresses
configured, as reported by Alex Sidorenko.
- Creates a new file, net/drivers/bonding/bond_ipv6.c, for the
IPv6-specific routines. Both regular bonds and VLANs over bonds
are supported.
- Adds a new tunable, num_unsol_na, to limit the number of unsolicited
IPv6 Neighbor Advertisements that are sent on a failover event.
Default is 1.
- Creates two new IPv6 neighbor discovery functions:
ndisc_build_skb()
ndisc_send_skb()
These were required to support VLANs since we have to be able to
add the VLAN id to the skb since ndisc_send_na() and friends
shouldn't be asked to do this. These two routines are basically
__ndisc_send() split into two pieces, in a slightly different order.
- Updates Documentation/networking/bonding.txt and bumps the rev of bond
support to 3.4.0.
On failover, this new code will generate one packet:
- An unsolicited IPv6 Neighbor Advertisement, which helps the switch
learn that the address has moved to the new slave.
Testing has shown that sending just the NA results in pretty good
behavior when in active-back mode, I saw no lost ping packets for example.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I have been tracking for a while a case where when the
network namespace exits the cleanup gets stck in an
endless precessess of:
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
It turns out that if you listen on a multicast address an unsubscribe
packet is sent when the network device goes down. If you shutdown
the network namespace without carefully cleaning up this can trigger
the unsubscribe packet to be sent over the loopback interface while
the network namespace is going down.
All of which is fine except when we drop the packet and forget to
free it leaking the skb and the dst entry attached to. As it
turns out the dst entry hold a reference to the idev which holds
the dev and keeps everything from being cleaned up. Yuck!
By fixing my earlier thinko and add the needed kfree_skb and everything
cleans up beautifully.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was recently hunting a bug that occurred in network namespace
cleanup. In looking at the code it became apparrent that we have
and will continue to have cases where if we have anything going
on in a network namespace there will be assumptions that the
loopback device is present. Things like sending igmp unsubscribe
messages when we bring down network devices invokes the routing
code which assumes that at least the loopback driver is present.
Therefore to avoid magic initcall ordering hackery that is hard
to follow and hard to get right insert a call to register the
loopback device directly from net_dev_init(). This guarantes
that the loopback device is the first device registered and
the last network device to go away.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When physical devices are inside of network namespace and that
network namespace terminates we can not make them go away. We
have to keep them and moving them to the initial network namespace
is the best we can do.
For virtual devices left in a network namespace that is exiting
we have no need to preserve them and we now have the infrastructure
that allows us to delete them. So delete virtual devices when we
exit a network namespace. Keeping the necessary user space clean up
after a network namespace exits much more tractable.
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix printk format warnings in net/9p.
Built cleanly on 7 arches.
net/9p/client.c:820: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:820: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:867: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:867: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:932: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:932: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'u64'
net/9p/client.c:982: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:982: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:1025: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:1025: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 7 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 12 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 8 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 13 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 7 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 12 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 8 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 13 has type 'u64'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Removed duplicated #include <rdma/ib_verbs.h> in
net/9p/trans_rdma.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
If a T or R fcall cannot be allocated, the function returns an error
but neglects to free the wait queue that was successfully allocated.
If it comes through again a second time this wq will be overwritten
with a new allocation and the old allocation will be leaked.
Also, if the client is subsequently closed, the close path will
attempt to clean up these allocations, so set the req fields to
NULL to avoid duplicate free.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
T and R fcall are reused until the client is destroyed. There does
not need to be a special case for Flush
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
The client lock must be IRQ safe. Some of the lock acquisition paths
took regular spin locks.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
The RDMA connection manager is fundamentally asynchronous.
Since the async callback context is the client pointer, the
transport in the client struct needs to be set prior to calling
the first async op.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Vito Caputo noticed that tcp_recvmsg() returns immediately from
partial reads when MSG_PEEK is used. In particular, this means that
SO_RCVLOWAT is not respected.
Simply remove the test. And this matches the behavior of several
other systems, including BSD.
Signed-off-by: David S. Miller <davem@davemloft.net>
With some net devices types, an IPv6 address configured while the
interface was down can stay 'tentative' forever, even after the interface
is set up. In some case, pending IPv6 DADs are not executed when the
device becomes ready.
I observed this while doing some tests with kvm. If I assign an IPv6
address to my interface eth0 (kvm driver rtl8139) when it is still down
then the address is flagged tentative (IFA_F_TENTATIVE). Then, I set
eth0 up, and to my surprise, the address stays 'tentative', no DAD is
executed and the address can't be pinged.
I also observed the same behaviour, without kvm, with virtual interfaces
types macvlan and veth.
Some easy steps to reproduce the issue with macvlan:
1. ip link add link eth0 type macvlan
2. ip -6 addr add 2003::ab32/64 dev macvlan0
3. ip addr show dev macvlan0
...
inet6 2003::ab32/64 scope global tentative
...
4. ip link set macvlan0 up
5. ip addr show dev macvlan0
...
inet6 2003::ab32/64 scope global tentative
...
Address is still tentative
I think there's a bug in net/ipv6/addrconf.c, addrconf_notify():
addrconf_dad_run() is not always run when the interface is flagged IF_READY.
Currently it is only run when receiving NETDEV_CHANGE event. Looks like
some (virtual) devices doesn't send this event when becoming up.
For both NETDEV_UP and NETDEV_CHANGE events, when the interface becomes
ready, run_pending should be set to 1. Patch below.
'run_pending = 1' could be moved below the if/else block but it makes
the code less readable.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed a contention on udp_memory_allocated on regular UDP applications.
While tcp_memory_allocated is seldom used, it appears each incoming UDP frame
is currently touching udp_memory_allocated when queued, and when received by
application.
One possible solution is to use sk_mem_reclaim_partial() instead of
sk_mem_reclaim(), so that we keep a small reserve (less than one page)
of memory for each UDP socket.
We did something very similar on TCP side in commit
9993e7d313
([TCP]: Do not purge sk_forward_alloc entirely in tcp_delack_timer())
A more complex solution would need to convert prot->memory_allocated to
use a percpu_counter with batches of 64 or 128 pages.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix printk format warnings in net/9p.
Built cleanly on 7 arches.
net/9p/client.c:820: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:820: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:867: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:867: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:932: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:932: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'u64'
net/9p/client.c:982: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:982: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:1025: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:1025: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 7 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 12 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 8 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 13 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 7 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 12 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 8 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 13 has type 'u64'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This inserts the required de-allocation routines for memory allocated
by feature negotiation in the socket destructors, replacing
dccp_feat_clean() in one instance.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides feature-negotiation initialisation for both DCCP sockets
and DCCP request_sockets, to support feature negotiation during
connection setup.
It also resolves a FIXME regarding the congestion control
initialisation.
Thanks to Wei Yongjun for help with the IPv6 side of this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds list initial fields and list management functions for the
new feature negotiation implementation.
Thanks to Arnaldo for suggestions and improvements.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
A lookup table for feature-negotiation information, extracted from RFC
4340/42, is provided by this patch. All currently known features can
be found in this table, along with their feature location, their
default value, and type.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares for the new and extended feature-negotiation
routines.
The following feature-negotiation data structures are provided:
* a container for the various (SP or NN) values,
* symbolic state names to track feature states,
* an entry struct which holds all current information together,
* elementary functions to fill in and process these structures.
Entry structs are arranged as FIFO for the following reason: RFC 4340
specifies that if multiple options of the same type are present, they
are processed in the order of their appearance in the packet; which
means that this order needs to be preserved in the local data
structure (the later insertion code also respects this order).
The struct list_head has been chosen for the following reasons: the most
frequent operations are
* add new entry at tail (when receiving Change or setting socket
options);
* delete entry (when Confirm has been received);
* deep copy of entire list (cloning from listening socket onto
request socket).
The NN value has been set to 64 bit, which is a currently sufficient
upper limit (Sequence Window feature has 48 bit).
Thanks to Arnaldo, who contributed the streamlined layout of the entry
struct.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The changes to deliver hardware accelerated VLAN packets to packet
sockets (commit bc1d0411) caused a warning for non-NAPI drivers.
The __vlan_hwaccel_rx() function is called directly from the drivers
RX function, for non-NAPI drivers that means its still in RX IRQ
context:
[ 27.779463] ------------[ cut here ]------------
[ 27.779509] WARNING: at kernel/softirq.c:136 local_bh_enable+0x37/0x81()
...
[ 27.782520] [<c0264755>] netif_nit_deliver+0x5b/0x75
[ 27.782590] [<c02bba83>] __vlan_hwaccel_rx+0x79/0x162
[ 27.782664] [<f8851c1d>] atl1_intr+0x9a9/0xa7c [atl1]
[ 27.782738] [<c0155b17>] handle_IRQ_event+0x23/0x51
[ 27.782808] [<c015692e>] handle_edge_irq+0xc2/0x102
[ 27.782878] [<c0105fd5>] do_IRQ+0x4d/0x64
Split hardware accelerated VLAN reception into two parts to fix this:
- __vlan_hwaccel_rx just stores the VLAN TCI and performs the VLAN
device lookup, then calls netif_receive_skb()/netif_rx()
- vlan_hwaccel_do_receive(), which is invoked by netif_receive_skb()
in softirq context, performs the real reception and delivery to
packet sockets.
Reported-and-tested-by: Ramon Casellas <ramon.casellas@cttc.es>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding MIGRATE support to strongSwan, Andreas Steffen noticed that
the selectors provided in XFRM_MSG_ACQUIRE have their family field
uninitialized (those in MIGRATE do have their family set).
Looking at the code, this is because the af-specific init_tempsel()
(called via afinfo->init_tempsel() in xfrm_init_tempsel()) do not set
the value.
Reported-by: Andreas Steffen <andreas.steffen@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
xfrm: Fix xfrm_policy_gc_lock handling.
niu: Use pci_ioremap_bar().
bnx2x: Version Update
bnx2x: Calling netif_carrier_off at the end of the probe
bnx2x: PCI configuration bug on big-endian
bnx2x: Removing the PMF indication when unloading
mv643xx_eth: fix SMI bus access timeouts
net: kconfig cleanup
fs_enet: fix polling
XFRM: copy_to_user_kmaddress() reports local address twice
SMC91x: Fix compilation on some platforms.
udp: Fix the SNMP counter of UDP_MIB_INERRORS
udp: Fix the SNMP counter of UDP_MIB_INDATAGRAMS
drivers/net/smc911x.c: Fix lockdep warning on xmit.
In net/ipv4/netfilter/nf_nat_rule.c, the function warn_if_extra_mangle was added
in commit 5b1158e909 (2006-12-02). I have a DNAT
target in the OUTPUT chain than changes connections with dst 2.0.0.1 to another
address which I'll substitute with 66.102.9.99 below.
On every boot I get the following message:
[ 146.252505] NAT: no longer support implicit source local NAT
[ 146.252517] NAT: packet src 66.102.9.99 -> dst 2.0.0.1
As far as I can tell from reading the function doing this, it should warn if the
source IP for the route to 66.102.9.99 is different from 2.0.0.1 but that is not
the case. It doesn't make sense to check the DNAT target against the local route
source.
Either the function should be changed to correctly check the route, or it should
be removed entirely as it's been nearly 2 years since it was added.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Now that ebt_unregister_table() can be called during netns stop, and module
pinning scheme can't prevent netns stop, do table cleanup by hand.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
* return ebt_table from ebt_register_table(), module code will save it into
per-netns data for unregistration
* duplicate ebt_table at the very beginning of registration -- it's added into
list, so one ebt_table wouldn't end up in many lists (and each netns has
different one)
* introduce underscored tables in individial modules, this is temporary to not
break bisection.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
* propagate netns from userspace, register table in passed netns
* remporarily register every ebt_table in init_net
P. S.: one needs to add ".netns_ok = 1" to igmp_protocol to test with
ebtables(8) in netns.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch modifies xt_NFLOG to suppress the call to nf_log_packet()
function. The call of this wrapper in xt_NFLOG was causing NFLOG to
use the first initialized module. Thus, if ipt_ULOG is loaded before
nfnetlink_log all NFLOG rules are treated as plain LOG rules.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: David S. Miller <davem@davemloft.net>
All these individual parsing functions never return an error,
so they can be void.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Alexey Dobriyan <adobriyan@gmail.com>
Based upon a lockdep trace by Simon Arlott.
xfrm_policy_kill() can be called from both BH and
non-BH contexts, so we have to grab xfrm_policy_gc_lock
with BH disabling.
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed duplicated #include <rdma/ib_verbs.h> in net/9p/trans_rdma.c
and #include <linux/thread_info.h> in net/socket.c
Signed-off-by: Jianjun Kong <jianjun@zeuux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I want to compile out proc_* and sysctl_* handlers totally and
stub them to NULL depending on config options, however usage of &
will prevent this, since taking adress of NULL pointer will break
compilation.
So, drop & in front of every ->proc_handler and every ->strategy
handler, it was never needed in fact.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gets about 1.25% back on tbench regression.
My change to NAPI for multiqueue support changed the time limit on
network receive processing. Under sustained loads like tbench, this
can cause the receiver to reschedule prematurely.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the 'supports_ipv6' scheduler flag since all schedulers now
support IPv6.
Signed-off-by: Julius Volz <julius.volz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 support to LBLC and LBLCR schedulers. These were the last
schedulers without IPv6 support, but we might want to keep the
supports_ipv6 flag in the case of future schedulers without IPv6
support.
Signed-off-by: Julius Volz <julius.volz@gmail.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since gso_skb is re-used for qdisc_peek_dequeued(), and this skb is
counted in the qdisc->q.qlen, it has to be kfreed during qdisc_reset()
when qlen is zeroed.
With help from David S. Miller <davem@davemloft.net>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding support for MIGRATE/KMADDRESS in strongSwan (as specified
in draft-ebalard-mext-pfkey-enhanced-migrate-00), Andreas Steffen
noticed that XFRMA_KMADDRESS attribute passed to userland contains the
local address twice (remote provides local address instead of remote
one).
This bug in copy_to_user_kmaddress() affects only key managers that use
native XFRM interface (key managers that use PF_KEY are not affected).
For the record, the bug was in the initial changeset I posted which
added support for KMADDRESS (13c1d18931
'xfrm: MIGRATE enhancements (draft-ebalard-mext-pfkey-enhanced-migrate)').
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Reported-by: Andreas Steffen <andreas.steffen@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP packets received in udpv6_recvmsg() are not only IPv6 UDP packets, but
also have IPv4 UDP packets, so when do the counter of UDP_MIB_INERRORS in
udpv6_recvmsg(), we should check whether the packet is a IPv6 UDP packet
or a IPv4 UDP packet.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski
Linus Torvalds
Oliver Hartkopp
Rémi Denis-Courmont
remi.denis-courmont@nokia
Martin Willi
Paul Moore
Wei Yongjun
David S. Miller
Eric Dumazet
Gerrit Renker
Marcel Holtmann
Vegard Nossum
Hannes Eder
Patrick McHardy
Randy Dunlap
Harvey Harrison
dann frazier
Ivan Kuten
Jouni Malinen
Henrique de Moraes Holschuh
Vivek Natarajan
Larry Finger
Luis R. Rodriguez
Stephen Hemminger
Arjan van de Ven
Alexey Dobriyan
Ingo Molnar
Daniel Lezcano
Ilpo Järvinen
Sujith
Abhijeet Kolekar
Eric Leblond
Jeff Kirsher
Bernard Pidoux
Herbert Xu
Tom Tucker
Qinghuang Feng
Catalin Marinas
Petr Tesarik
Johannes Berg
John W. Linville
Rami Rosen
Tomas Winkler
Andrey Yurovsky
Alexander Duyck
Trond Myklebust
Wang Chen
Benjamin Thery
Balazs Scheidler
Pablo Neira Ayuso
Ulrich Drepper
Joe Perches
Robert Olsson
James Morris
Ben Greear
Pavel Emelyanov
David Howells
Arnaud Ebalard
Brian Haley
Patrick Ohly
Doug Leith
Lennert Buytenhek
Jianjun Kong
Jesse Brandeburg
Kay Sievers
Ferenc Wagner
Holger Schurig
Zhu Yi
Miklos Szeredi
Thomas Graf
Eric W. Biederman
Jonathan McDowell
Eric W. Biederman
Roel Kluin
Huang Weiyi
Andreas Steffen
Simon Arlott
Julius Volz