These enums have been separate since the dawn of SAS, mainly because the
latter is a procotol only enum and the former includes additional state
for libsas. The dichotomy causes endless confusion about which one you
should use where and leads to pointless warnings like this:
drivers/scsi/mvsas/mv_sas.c: In function 'mvs_update_phyinfo':
drivers/scsi/mvsas/mv_sas.c:1162:34: warning: comparison between 'enum sas_device_type' and 'enum sas_dev_type' [-Wenum-compare]
Fix by eliminating one of them. The one kept is effectively the sas.h
one, but call it sas_device_type and make sure the enums are all
properly namespaced with the SAS_ prefix.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If userspace has decided to disable a phy the kernel should honor that
and not inadvertantly re-enable the phy via error recovery. This is
more straightforward in the sata case where link recovery (via
libata-eh) is separate from sas_task cancelling in libsas-eh. Teach
libsas to accept -ENODEV as a successful response from I_T_nexus_reset
('successful' in terms of not escalating further).
This is a more comprehensive fix then "libsas: don't recover 'gone'
devices in sas_ata_hard_reset()", as it is no longer sata-specific.
aic94xx does check the return value from sas_phy_reset() so if the phy
is disabled we proceed with clearing the I_T_nexus.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the direct-attached case this routine returns the phy on which this
device was first discovered. Which is broken if we want to support
wide-targets, as this phy reference can become stale even though the
port is still active.
In the expander-attached case this routine tries to lookup the phy by
scanning the attached sas addresses of the parent expander, and BUG_ONs
if it can't find it. However since eh and the libsas workqueue run
independently we can still be attempting device recovery via eh after
libsas has recorded the device as detached. This is even easier to hit
now that eh is blocked while device domain rediscovery takes place, and
that libata is fed more timed out commands increasing the chances that
it will try to recover the ata device.
Arrange for dev->phy to always point to a last known good phy, it may be
stale after the port is torn down, but it will catch up for wide port
reconfigurations, and never be NULL.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
[jejb: limit ioctl to returning 20 characters to avoid overrun
on long device names and add a few more conversions]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
[jejb: fixed up a ton of missed conversions.
All of you are on notice this has happened, driver trees will now
need to be rebased]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: SCSI List <linux-scsi@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- static functions in .c files shouldn't be marked inline
- make needlessly global code static
- remove the unused aic94xx_seq.c:asd_unpause_lseq()
- #if 0 other unused code
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is a particularly nasty bug. The problem is that if any internal
ascb times out, currently we free it even though it's pending at the
sequencer. This results in the sequencer getting terminally confused
and the error message:
BUG:sequencer:dl:no ascb
Being returned when it comes back. The way to fix this is to manage
freeing the ascb from the tasklet completion routine, so that we only
free it when the sequencer actually returns it. The code is also
altered to use on stack completions and transfer variables.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently aic94xx has no exported I_T_nexus_reset function. This is a
bit of a huge problem, since sas_ata relies on this function to
perform an ATA phy reset and also it means that if abort fails, we
really have no bigger hammer to hit everything with.
Plumb in the I_T_nexus_reset by quiescing the sequencer, sending the
correct phy reset (link for ATA and hard for SAS) and then carefully
resuming the sequencer again.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The clear nexus I_T and clear nexus I_T_L functions in the aic94xx
specify the SUSPEND_TX flag which causes the sequencer to be suspended
until it receives a RESUME_TX. Unfortunately, nothing ever sends the
resume, so the sequencer on the link is stopped forever, leading to
eventual timeouts and I/O errors.
Since clear nexus commands are only executed as part of error recovery,
it's perfectly fine to keep the sequencer running on the link ... as
soon as the recovery function is completed, we'll send it the commands
to retry.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
include/scsi/scsi.h as a definition:
#define ABORT_TASK 0x0d
on the other hand drivers/scsi/aic94xx/aic94xx_sas.h has:
#define ABORT_TASK 0x03
rename the latter to SCB_ABORT_TASK
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sparse complains about the mixing of enums in libsas. Since the
underlying numeric values of both enums are the same, combine them
to get rid of the warning.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Every so often, the driver will call asd_clear_nexus to clean out a task.
It is supposed to be the case that the CLEAR NEXUS does not go on the done
list until after the task itself has been put on the done list, but for
some reason this doesn't always happen. Thus, the
wait_for_completion_timeout call times out, and we return success. This
makes libsas free the task even though the task hasn't completed, leading
to a BUG_ON message from aic94xx_hwi.c around line 341. We should return
failure from asd_clear_nexus so that libsas tries again; at a bare minimum
it shouldn't be freeing active tasks. I _think_ this will fix one of
the SCB timeout crash problems (though I've not been able to reproduce
it lately...)
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In asd_initiate_ssp_tmf, the TMF result code is replaced with
TMF_RESP_FUNC_FAILED except when the TMF returns a result code immediately.
However, TMFs can return result codes via an ESCB... yet these codes are
also replaced with "FAILED". The only values that can fall into that case
are TMF_* codes anyway, so get rid of this code where COMPLETE and SUCCESS
are turned into FAILED. This also lets us propagate those TMF_* codes up
to the caller.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In this driver, TMF_QUERY_TASK translates to QUERY_SSP_TASK. The
sequencer, it seems, is perfectly happy sending us a SSP response, which
this function promptly "converts" into TMF_RESP_FUNC_FAILED. This leads to
the SAS EH making bad decisions based on bad data, so we should not perform
the conversion in this case.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is the end point of the separate aic94xx driver based on the
original driver and transport class from Luben Tuikov
<ltuikov@yahoo.com>
The log of the separate development is:
Alexis Bruemmer:
o aic94xx: fix hotplug/unplug for expanderless systems
o aic94xx: disable split completion timer/setting by default
o aic94xx: wide port off expander support
o aic94xx: remove various inline functions
o aic94xx: use bitops
o aic94xx: remove queue comment
o aic94xx: remove sas_common.c
o aic94xx: sas remove depot's
o aic94xx: use available list_for_each_entry_safe_reverse()
o aic94xx: sas header file merge
James Bottomley:
o aic94xx: fix TF_TMF_NO_CTX processing
o aic94xx: convert to request_firmware interface
o aic94xx: fix hotplug/unplug
o aic94xx: add link error counts to the expander phys
o aic94xx: add transport class phy reset capability
o aic94xx: remove local_attached flag
o Remove README
o Fixup Makefile variable for libsas rename
o Rename sas->libsas
o aic94xx: correct return code for sas_discover_event
o aic94xx: use parent backlink port
o aic94xx: remove channel abstraction
o aic94xx: fix routing algorithms
o aic94xx: add backlink port
o aic94xx: fix cascaded expander properties
o aic94xx: fix sleep under lock
o aic94xx: fix panic on module removal in complex topology
o aic94xx: make use of the new sas_port
o rename sas_port to asd_sas_port
o Fix for eh_strategy_handler move
o aic94xx: move entirely over to correct transport class formulation
o remove last vestages of sas_rphy_alloc()
o update for eh_timed_out move
o Preliminary expander support for aic94xx
o sas: remove event thread
o minor warning cleanups
o remove last vestiges of id mapping arrays
o Further updates
o Convert aic94xx over entirely to the transport class end device and
o update aic94xx/sas to use the new sas transport class end device
o [PATCH] aic94xx: attaching to the sas transport class
o Add missing completion removal from prior patch
o [PATCH] aic94xx: attaching to the sas transport class
o Build fixes from akpm
Jeff Garzik:
o [scsi aic94xx] Remove ->owner from PCI info table
Luben Tuikov:
o initial aic94xx driver
Mike Anderson:
o aic94xx: fix panic on module insertion
o aic94xx: stub out SATA_DEV case
o aic94xx: compile warning cleanups
o aic94xx: sas_alloc_task
o aic94xx: ref count update
o aic94xx nexus loss time value
o [PATCH] aic94xx: driver assertion in non-x86 BIOS env
Randy Dunlap:
o libsas: externs not needed
Robert Tarte:
o aic94xx: sequence patch - fixes SATA support
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley
Dan Williams
Tejun Heo
Kay Sievers
Harvey Harrison
Adrian Bunk
James Bottomley
Boaz Harrosh
Darrick J. Wong
James Bottomley