TASCAM FireWire series uses non-blocking transmission for AMDTP packet
streaming, while the format of data blocks is unique.
The CIP headers includes specific value in FMT field and no SYT
information.
In transmitted packets, the first data channel represents event counter,
and the last data channel has status and control information. The rest
has 24bit PCM samples with right padding.
In received packets, all of data channels include 16, 24, 32bit PCM
samples. There's no other kind of information.
This commit adds support for this protocol. For convenience, the size of
PCM samples in outgoing packet is limited by 16 and 24bit. The status and
control information will be supported in future commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series has certain registers for firmware information.
This commit adds proc node to show the information.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series doesn't tell drivers their capabilities, thus
the drivers should have model-dependent parameters and apply it to
detected devices.
This commit adds a structure to represent such parameters.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new driver for TASCAM FireWire series. In this commit,
this driver just creates/removes card instance according to bus event.
More functionalities will be added in following commits.
TASCAM FireWire series consists of:
* PDI 1394P23 for IEEE 1394 PHY layer
* PDI 1394L40 for IEEE 1394 LINK layer and IEC 61883 interface
* XILINX XC9536XL
* XILINX Spartan-II XC2S100
* ATMEL AT91M42800A
Ilya Zimnovich had investigated TASCAM FireWire series in 2011, and
discover some features of his FW-1804. You can see a part of his research
in FFADO project.
http://subversion.ffado.org/wiki/Tascam
A part of my work are based on Ilya's investigation, while this series
doesn't support the FW-1804, because of a lack of config ROM
information and its protocol detail, especially for PCM channels.
I observed that FW-1884 and FW-1082 don't work properly with 1394 OHCI
controller based on VT6315. The controller can actually communicate packets
to these models, while these models generate no sounds. It may be due to
the PHY/LINK layer issues. Using 1394 OHCI controller produced by the other
vendors such as Texas Instruments may work. Or adding another node on the
bus.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Digi 002/003 family uses asynchronous transaction for messaging.
The address to transmit this message is stored on a certain register.
This commit allocates a range of address on OHCI 1394 host controller
to handle the messaging. As long as I know, the purpose of this message
seems to notify lost of synchronization. While, the meaning of content
of the message is not clear.
Actual examples of this messaging:
* When clock source is set as internal:
- 0x00007051
- 0x00007052
- 0x00007054
- 0x00007057
- 0x00007058
* When clock source is set as somewhat external:
- 0x00009000
- 0x00009010
- 0x00009020
- 0x00009021
- 0x00009022
The lost often occurs when using internal clock source. In this case,
users hear sounds with quite short gap every several minutes. In fact,
the lost is recovered temporarily.
When using with external clock source, the lost seems not to occur. The
mechanism is not clear yet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds hwdep interface so as the other sound drivers for units
on IEEE 1394 bus have.
This interface is designed for mixer/control applications. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds PCM functionality to transmit/receive PCM samples.
Any PCM substreams are jointed because incoming/outgoing AMDTP streams
are bound. When one of PCM substream is running or external clock source
is selected, current sampling rate is used. Else, the sampling rate is
changed as an userspace application requests.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds proc node to show current clock status for debugging.
As long as testing Digi 002 rack, registers can show local clock rate,
local clock source. When external clock input such as S/PDIF is
connected, the registers show the detection and external clock rate.
Additionally, the registers show the mode of optical digital input
interface. Although, a tester with Digi 003 rack reports this makes no
sense. Further investigation is required for Digi 003 series.
Besides, in Digi 002 rack, the S/PDIF format must be IEC 60958-4,
so-called professional.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a functionality to manage streaming.
The streaming is not controlled by CMP in IEC 61883-6. It's controlled by
IEEE 1394 write transaction to certain addresses.
Several clock sources are available, while there're no differences about
packet transmission. The value of SYT field in transmitted packets is
always zero. Thus, streams in both direction don't build synchronization.
And the device always requires received packets to transmit packets. This
driver keeps to transfer outgoing stream even if they're not required.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Digi 002/003 family uses its own format for data blocks. The format is
quite similar to AM824 in IEC 61883-6, while there're some differences:
* The Valid Bit Length (VBL) code is always 0x40 in Multi-bit Linear Audio
(MBLA) data channel.
* The first data channel includes MIDI messages, against IEC 61883-6
recommendation.
* The Counter field is always zero in MIDI conformant data channel.
* Sequence multiplexing in IEC 61883-6 is not applied to the MIDI
conformant data channel.
* PCM samples are scrambled in received AMDTP packets. We call the way
as Double-Oh-Three (DOT). The algorithm was discovered by
Robin Gareus and Damien Zammit in 2012.
This commit adds data processing layer to satisfy these differences.
There's a quirk about transmission mode for received packets. When this
driver applies non-blocking mode to outgoing packets with isochronous
channel 2 or more, after 15 to 20 seconds since playbacking, any PCM
samples causes noisy sound on the device. With isochronous channel 0 or 1,
this doesn't occur. As long as I investigated, this quirk is not observed
when applying blocking mode to the received packets.
This driver applies blocking mode to outgoing packets, while non-blocking
mode to incoming packgets.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new driver for Digidesign 002/003 family. This commit
just creates/removes card instance according to bus event. More functions
will be added in following commits.
Digidesign 002/003 family consists of:
* Agere FW802B for IEEE 1394 PHY layer
* PDI 1394L40 for IEEE 1394 LINK layer and IEC 61883 interface
* ALTERA ACEX EP1K50 for IEC 61883 layer and DSP controller
* ADSP-21065L for signal processing
[minor cleanup using skip_spaces() by tiwai]
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit moves the codes related to data block processing from packet
streaming layer to AM824 layer.
Each driver initializes amdtp stream structure for AM824 data block by
calling amdtp_am824_init(). Then, a memory block is allocated for AM824
specific structure. This memory block is released by calling
amdtp_stream_destroy().
When setting streaming parameters, it calls amdtp_am824_set_parameters().
When starting packet streaming, it calls amdtp_stream_start(). When
stopping packet streaming, it calls amdtp_stream_stop().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit renames some macros just related to AM824 format. In later
commit, they're moved to AM824 layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Setting the format of PCM substream to AMDTP stream structure is important
to set a handler to copy actual PCM samples between buffers. The
processing should be in data block processing layer because essentially
it has no relationship to packet streaming.
This commit renames PCM format setting function to prepare for integrating
AM824 layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, MIDI messages are transferred in MIDI conformant data
channel. Essentially, packet streaming layer is not responsible for MIDI
functionality.
This commit moves MIDI trigger helper function from the layer to AM824
layer. The rest of codes related to MIDI functionality will be moved in
later commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, several types of data are available in AM824 format. The
data is transferred in each data channel. The position of data channel in
data block differs depending on model.
Current implementation has an array to map the index of data channel in an
data block to the position of actual data channel. The implementation
allows each driver to access the mapping directly.
In later commit, the mapping is in specific structure pushed into an
opaque pointer. Helper functions are required.
This commit adds the helper functions for this purpose. In IEC 61883-6,
AM824 format supports many data types, while this specification easily
causes over-engineering. Current AM824 implementation is allowed to handle
two types of data, Multi Bit Linear Audio data (=PCM samples) and MIDI
conformant data (=MIDI messages).
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, PCM frames are transferred in Multi Bit Linear Audio data
channel. The data channel transfers 16/20/24 bit PCM samples. Thus, PCM
substream has a constrain about it.
This commit moves codes related to the constraint from packet streaming
layer to AM824 data block processing layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The value of FDF field in CIP header is protocol-dependent. Thus, it's
better to allow data block processing layer to decide the value in any
timing.
In AM824 data format, the value of FDF field in CIP header indicates
N-flag and Nominal Sampling Frequency Code (sfc). The N-flag is for
switching 'Clock-based rate control mode' and 'Command-based rate control
mode'. In our implementation, 'Clock-based rate control mode' is just
supported. Therefore, When sampling transfer frequency is decided, then
the FDF can be set.
This commit replaces 'amdtp_stream_set_parameters' with
'amdtp_am824_set_parameters' to set the FDF. This is the same timing
to decide the ration between the number of data blocks and the number of
PCM frames.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds data block processing layer for AM824 format. The new
layer initializes streaming layer with its value for fmt field.
Currently, most implementation of data block processing still remains
streaming layer. In later commits, these codes will be moved to the layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In later commit, data block processing layer will be newly added. This
layer will be named as 'amdtp-am824'.
This commit renames current amdtp file to amdtp-stream, to distinguish it
from the new layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some vendor specific protocol uses its own value for fmt/fdf fields in
CIP header.
This commit support to set arbitrary values for the fields.
In IEC 61883-6, NO-DATA code is defined for FDF field. A packet with this
code includes no data even if it includes some data blocks. This commit
still leaves a condition to handle this special packet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA PCM framework uses PCM buffer with a concept of 'period' to
synchronize userspace operations to hardware for nearly-realtime
processing. Each driver implements snd_pcm_period_elapsed() to tell across
of the period boundary to ALSA PCM middleware. To call the function, some
drivers utilize hardware interrupt handlers, the others count handled PCM
frames.
Drivers for sound units on IEEE 1394 bus are the latter. They use two
buffers; PCM buffer and DMA buffer for IEEE 1394 isochronous packet. PCM
frames are copied between these two buffers and 'amdtp_stream' structure
counts the handled PCM frames. Then, snd_pcm_period_elapsed() is called if
required.
Essentially, packet streaming layer should not be responsible for PCM
frame processing. The PCM frame processing should be handled in each data
block processing layer as a result of handling data blocks. Although, PCM
frame counting is a common work for all of protocols which ALSA firewire
stack is going to support.
This commit adds two new helper functions as interfaces between packet
streaming layer to data block processing layer. In future, each data block
processing layer implements these functions. The packet streaming layer
calls data block processing layer per packet by calling the functions. The
data block processing layer processes data blocks and PCM frames, and
returns the number of processed PCM frames. Then the packet streaming layer
calculates handled PCM frames and calls snd_pcm_period_elapsed().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In future commit, interface between data block processing layer and packet
stream processing layer is defined. These two layers communicate the
number of data blocks and the number of PCM frames.
The data block processing layer has a responsibility for calculating the
number of PCM frames. Therefore, 'dual wire' of Dice quirk should be
handled in data block processing layer.
This commit adds a member of 'frame_multiplier'. This member represents
the ratio of the number of PCM frames against the number of data blocks.
Usually, the value of this member is 1, while it's 2 in Dice's 'dual wire'.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, one data block represents one event. In ALSA, the event is
one PCM frame. Therefore, when processing one data block, current
implementation counts one PCM frame.
On the other hand, Dice platform has a quirk called as 'dual wire' at
higher sampling rate. In detail, see comment of commit 6eb6c81eee
("ALSA: dice: Split stream functionality into a file").
Currently, to handle this quirk, AMDTP stream structure has a
'double_pcm_frames' member. When this is enabled, two PCM frames are
counted. Each driver set this flag by accessing the structure member
directly.
In future commit, some members related to AM824 data block will be moved
to specific structure, to separate packet streaming layer and data block
processing layer. The access will be limited by opaque pointer.
For this reason, this commit adds an argument into
amdtp_stream_set_parameter() to set the flag.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, amdtp_stream_set_parameters() returns no error even if wrong
arguments are given. This is not good for streaming layer because drivers
can continue processing ignoring capability of streaming layer.
This commit changes this function to return error code.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In later commit, some members related to AM824 data format will be moved
from AMDTP stream structure to data block structure. This commit is a
preparation for it. Additionally, current layout of AMDTP stream structure
is a bit mess by several extensions. This commit also arranges the layout.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mackie Onyx Satellite has two usage; standalone and with base station.
These two modes has different stream formats. In standalone mode, rx data
block includes 2 Multi Bit Linear Audio (MBLA) data channels and tx data
block includes 2. With base station, they're 6 and 2.
Although, with base station, the actual tx packet include wrong value in
'dbs' field in its CIP header. This quirk causes packet streaming layer to
detect packet discontinuity and to stop PCM substream.
This is a response of 'single' subfunction 'extended stream format
information' command in AV/C Stream Format Information Specification 1.1.
It means that a data block in tx packets includes 2 MBLA data channels.
$ ./firewire-request /dev/fw1 fcp 0x01ffbfc001000000ffffffff
response: 000: 0c ff bf c0 01 00 00 00 ff 00 90 40 03 02 01 02
response: 010: 06
Current OXFW driver parses the response and detects stream formats
correctly.
$ cat /proc/asound/card1/firewire/formation
...
Output Stream from device:
Rate PCM MIDI
* 48000 2 0
44100 2 0
88200 2 0
96000 2 0
On the other hand, in actual tx CIP, the 'dbs' field has 6. But the number
of quadlets in CIP payload is not multiple of 6. Seeing the subtraction of
two successive payload quadlets, it should be multiple of 2.
payload CIP CIP
quadlets header0 header1
24 00060052 9002ffff
24 0006005e 9002ffff
26 0006006a 9002ffff
24 00060077 9002ffff
24 00060083 9002ffff
26 0006008f 9002ffff
24 0006009c 9002ffff
24 000600a8 9002ffff
26 000600b4 9002ffff
24 000600c1 9002ffff
This commit adds support for this quirk to OXFW driver, by using
CIP_WRONG_DBS flag. When this flag is set, packet streaming layer uses
the value of its 'data_block_quadlets' member instead of the value in CIP
header. This value is already set by OXFW driver and no discontinuity is
detected.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In PCM core, when hw_params() in each driver returns error, the state of
PCM substream is kept as 'open'. In this case, current drivers for sound
units on IEEE 1394 bus doesn't decrement substream counter in hw_free()
correctly. This causes these drivers to keep streams even if not
required.
This commit fixes this bug. When snd_pcm_lib_alloc_vmalloc_buffer()
fails, hw_params function in each driver returns without incrementing the
counter.
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireworks uses TSB43CB43(IceLynx-Micro) as its IEC 61883-1/6 interface.
This chip includes ARM7 core, and loads and runs program. The firmware
is stored in on-board memory and loaded every powering-on from it.
Echo Audio ships several versions of firmwares for each model. These
firmwares have each quirk and the quirk changes a sequence of packets.
As long as I investigated, AudioFire2/AudioFire4/AudioFirePre8 have a
quirk to transfer a first packet with 0x02 in its dbc field. This causes
ALSA Fireworks driver to detect discontinuity. In this case, firmware
version 5.7.0, 5.7.3 and 5.8.0 are used.
Payload CIP CIP
quadlets header1 header2
02 00050002 90ffffff <-
42 0005000a 90013000
42 00050012 90014400
42 0005001a 90015800
02 0005001a 90ffffff
42 00050022 90019000
42 0005002a 9001a400
42 00050032 9001b800
02 00050032 90ffffff
42 0005003a 9001d000
42 00050042 9001e400
42 0005004a 9001f800
02 0005004a 90ffffff
(AudioFire2 with firmware version 5.7.)
$ dmesg
snd-fireworks fw1.0: Detect discontinuity of CIP: 00 02
These models, AudioFire8 (since Jul 2009 ) and Gibson Robot Interface
Pack series uses the same ARM binary as their firmware. Thus, this
quirk may be observed among them.
This commit adds a new member for AMDTP structure. This member represents
the value of dbc field in a first AMDTP packet. Drivers can set it with
a preferred value according to model's quirk.
Tested-by: Johannes Oertei <johannes.oertel@uni-due.de>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 9c6893e0be.
The fix is superseded by the next commit as a better implementation
for supporting AudioFire2/AudioFire4/AudioFirePre8 quirks.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireworks uses TSB43CB43(IceLynx-Micro) as its IEC 61883-1/6 interface.
This chip includes ARM7 core, and loads and runs program. The firmware
is stored in on-board memory and loaded every powering-on.
Echo Audio ships several versions of firmwares for each model. These
firmwares have each quirk and the quirk changes a sequence of packets.
AudioFire2 has a quirk to transfer a first packet with non-zero in
its dbc field. This causes ALSA Fireworks driver to detect discontinuity.
As long as I investigated, firmware 5.7, 5.7.6 and 5.8 have this quirk.
This commit adds a support for the quirk to handle AudioFire2 packets.
For safe, CIP_SKIP_INIT_DBC_CHECK is applied to all versions of
AudioFire2's firmwares.
02 00050002 90ffffff <-
42 0005000a 90013000
42 00050012 90014400
42 0005001a 90015800
02 0005001a 90ffffff
42 00050022 90019000
42 0005002a 9001a400
42 00050032 9001b800
02 00050032 90ffffff
42 0005003a 9001d000
42 00050042 9001e400
42 0005004a 9001f800
02 0005004a 90ffffff
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Behringer FCA610 transmits packets with periodic noisy PCM samples
when receiving no streams, and generates a bit noisy sound.
ALSA BeBoB driver is programmed to establish both in/out connections
when starting streaming, then transfers packets as userspace applications
requested. This means that there's a case that one of incoming/outgoing
streams is running, to save CPU and bandwidth usage. Although, it's natural
to start transferring packets in both direction.
This commit makes this driver to keeps duplex streams always.
Tested-by: Kim Tore Jensen <kim@incendio.no>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Behringer FCA610 and UFX1604 is confirmed to require more time till
transmitting packets after establishing connections. This seems to
be a quirk of DM1500 ASIC which ArchWave produced.
For this quirk, this commit extends the time to wait up to 2 seconds.
As a result, in worst cases, below userspace functions require 2 seconds
to return.
- snd_pcm_prepare()
- snd_pcm_hw_params()
- snd_pcm_recover()
Tested-by: Kim Tore Jensen <kim@incendio.no>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BeBoB installed devices have BeBoB register area. This area stores
basic information about its firmware. A register has its protocol
version.
This commit adds 'version' member and store the device's protocol
version to handle v3 quirks in following commits.
Tested-by: Kim Tore Jensen <kim@incendio.no>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In previous commits, this driver can detect the source of clock as mush
as possible. SYT-Match mode is also available.
This commit purge the restriction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The old string literals were completely replaced by new normalized
representation.
This commit obsoletes it.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit changes function prototype and its processing. As a result,
function caller can execute additional processing according to detected
clock source.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Previous commit adds a enumerator as a normalized representation of
clock source, while model-dependent structures still use string literals
for this purpose.
This commit is a preparation for replacement.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Previous commit allows this driver to detect several types of clock
source, while there's no normalized expression for it.
This commit adds a new enumerator for this purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With BeBoB version 3, current ALSA BeBoB driver detects the type of
current clock signal source wrongly. This is due to a lack of proper
implementation to parse the information.
This commit renews the parser. As a result, this driver detects
SYT-Match clock signal, thus it can start streams with two modes;
SYT-Match mode and the others. SYT-Match mode will be supported in future
commits.
There's a constrain about detected internal/external clock source.
When detecting external clock source, this driver allows userspace
applications to use current sampling rate only. This is due to consider
abour synchronization to external clock sources such as S/PDIF, ADAT or
word-clock.
According to several information from some devices, I guesss that the
internal clock of most devices synchronize to IEEE 1394 cycle start
packet. In this case, by a usual way, it's detect as 'Sync type
of output Music Sub-Unit' connected to 'Sync type of PCR output Unit
(oPCR)', and this driver judges it as internal clock. Therefore,
userspace applications is allowed to request arbitrary supported sampling
rates.
On the other hand, several devices based on BeBoB version 3 have
additional internal clock. In this case, by a usual way, it's detect as
'Sync/Additional type of External input Unit'. Unfortunately, there's no
way to distinguish this sync type from the other external clock sources
such as word-clock. In this case, this driver handles it as external and
userspace applications is forced to use current sampling rate.
I note that when the source of clock is detected as 'Isochronous stream
type of input PCR[0]', it's under 'SYT-Match' mode. In this mode, the
synchronization clock is generated according to SYT-series in received
packets. In this case, this driver generates the series by myself. I
experienced this mode often make the device silent suddenly during
playbacking. This means that the mode is easy to lost synchronization.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When detecting packet discontinuity, handle_in_packet() returns minus value
and this value is assigned to unsigned int variable, then the variable has
huge value. As a result, the variable causes buffer-over-run in
handle_out_packet(). This brings invalid page request and system hangup.
This commit fixes the bug to add a new argument into handle_in_packet()
and the number of handled data blocks is assignd to it. The function
return value is just used to check error.
I also considered to change the type of local variable to 'int' in
in_stream_callback(). This idea is based on type-conversion in C standard,
while it may cause future problems when adding more works. Thus, I dropped
this idea.
Fixes: 6fc6b9ce41c6('ALSA: firewire-lib: pass the number of data blocks in incoming packets to outgoing packets')
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This device is based on DM1000E, and BeBoB version 1 firmware is
installed.
$ cat /proc/asound/cards
0 [Pro ]: BeBoB - Mbox 2 Pro
DIGIDESIGN Mbox 2 Pro (id:1, rev:1),
GUID 00a07e0100a90000 at fw1.0, S400
$ cat /proc/asound/Pro/firewire/firmware
Manufacturer: bridgeCo
Protocol Ver: 1
Build Ver: 0
GUID: 0x00A07E0100A90000
Model ID: 0x01
Model Rev: 1
Firmware Date: 20071031
Firmware Time: 034402
Firmware ID: 0xA9
Firmware Ver: 16777215
Base Addr: 0x20080000
Max Size: 1572864
Loader Date: 20051207
Loader Time: 205554
With this patch, ALSA BeBoB driver can start packet streaming to/from
this model, while as a default, internal multiplexer of this model is
not initialized and generates no sound even if the driver transfers
any packets with PCM samples. To hear any sounds from this model,
userspace applications should be developed to set parameters to the
internal multiplexer. You can see raw information in FFADO website:
http://subversion.ffado.org/wiki/AvcModels/DigiDesignMboxPro2
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When detecting zero in 'dbs' field of CIP header, this packet streaming
should be aborted because of avoiding division-by-zero. This is an error
in an aspect of IEC 61883-1, thus protocol error.
This commit use EPROTO instead of EIO. Actually, the returned value is
not used for userspace and this commit has no effect.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When detecting invalid value in 'dbs' field of CIP header or packet
discontinuity, current implementation reports the status by err_info().
In most cases this state is caused by model-specific issue due to
vendor's customization and should be reported to developers.
This commit use dev_err() instead of dev_info() for this purpose.
In the cases, packet streaming is aborted, thus no message floading
occurs.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some macros include my misunderstanding for IEC 61883-1 or -6.
Additionally, some fixed values appear on codes.
This commit replaces these with macros with proper names.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The naming rule for local functions was inconsistent. This commit
rename them with a consistent manner.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Former patches allow non-blocking streams to synchronize with timestamp.
This patch removes the restriction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In previous commit, error handling for incoming packet processing is
outside of packetization. This is nice for reading the codes.
This commit applies this idea for outgoing packet processing, too.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current implementation reuses the value of syt field in incoming packet to
outgoing packet for full duplex timestamp synchronization, while the number
of data blocks in outgoing packets refers to hard-coded table and the
synchronization cannot be applied to non-blocking stream.
This commit passes the number of data blocks from incoming packet
processing to outgoing packet processing for the synchronization. For
normal mode, isochronous callback handler is changed to generate the values
of syt and data blocks.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This function is called according to conditions between the value of
syt and streaming mode(blocking or non-blocking).
To simplify caller's work, this commit push these conditions to the
function.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, the number of data blocks in a packet is limited up to
the value of SYT_INTERVAL. Current implementation is compliant to the
limitation, while it can cause buffer-over-run when the value of dbs
field in received packet is illegally large.
This commit adds a validator to detect such illegal packets to prevent
the buffer-over-run. Actually, the buffer is aligned to the size of memory
page, thus this issue hardly causes system errors due to the room to page
alignment, as long as a few packets includes such jumbo payload; i.e.
a packet to several received packets.
Here, Behringer F-Control Audio 202 (based on OXFW 960) has a quirk to
postpone transferring isochronous packet till finish handling any
asynchronous packets. In this case, this model is lazy, transfers no
packets according to several cycle-start packets. After finishing, this
model pushes required data in next isochronous packet. As a result, the
packet include more data blocks than IEC 61883-6 defines.
To continue to support this model, this commit adds a new flag to extend
the length of calculated payload. This flag allows the size of payload
5 times as large as IEC 61883-6 defines. As a result, packets from this
model passed the validator successfully.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some M-Audio devices require to receive bootup command just after
powering on, while codes in BeBoB driver doesn't work properly in
big-endian machine because the command should be aligned by
little-endian.
This commit fixes this bug. This fix should go to stable kernel.
Cc: Takayuki Shiroma <t.shiroma.oki@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With previous commit, this module managed to leave the counting to each
drivers, but the isochronous resources functionality still increment/decrement
the count.
This commit purge such codes to leave the responsibility to each drivers.
Fix: c6f224dc20 ('ALSA: firewire-lib: remove reference counting')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For received packet stream, the offset of 'RX_SEQ_START' locates after
the offset of 'RX_NUMBER_MIDI', although current macro and proc output
includes wrong offsets.
Fortunately, this bug doesn't affect streaming functionality because
these macro is not used.
This commit fixes these wrong macro and outputs.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The amdtp_stream_wait_callback() doesn't return minus value and
the return code is not for error code.
This commit fixes with a propper condition and an error code.
Fixes: f3699e2c77 ('ALSA: oxfw: Change the way to start stream')
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A part of these drivers, especially BeBoB driver, are programmed to wait
some events. Thus the drivers should not destroy any data in .remove()
context.
This commit moves some destructors from 'struct fw_driver.remove()' to
'struct snd_card.private_free()' to shutdown safely.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently stream destructor in each driver has a problem to be called in
a context in which sound card object is released, because the destructors
call amdtp_stream_pcm_abort() and touch PCM runtime data.
The PCM runtime data is destroyed in application's context with
snd_pcm_close(), on the other hand PCM substream data is destroyed after
sound card object is released, in most case after all of ALSA character
devices are released. When PCM runtime is destroyed and PCM substream is
remained, amdtp_stream_pcm_abort() touches PCM runtime data and causes
Null-pointer-dereference.
This commit changes stream destructors and allows each driver to call
it after releasing runtime.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AMDTP helper functions increment/decrement reference counter for an
instance of FireWire unit, while it's complicated for each driver to
process error state.
In previous commit, each driver has the role of reference counting. This
commit removes this role from the helper function.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireworks and Dice drivers try to touch instances of FireWire unit after
sound card object is released, while references to the unit is decremented
in .remove(). When unplugging during streaming, sound card object is
released after .remove(), thus Fireworks and Dice drivers causes GPF or
Null-pointer-dereferencing to application processes because an instance of
FireWire unit was already released.
This commit adds reference-counting for FireWire unit in drivers to allow
them to touch an instance of FireWire unit after .remove(). In most case,
any operations after .remove() may be failed safely.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The sign for microsecond (U+0085, MICRO SIGN) was encoded to '0x c2 b5'
by UTF-8 character encoding scheme. But the byte sequence was converted
to '0x c3 82 c2 b5' in a previous commit. As a result, the byte
sequence cannot represent microsecond sign in UTF-8 or ASCII. This
may confuse developers.
This commit replaces the sign to string expression with 'microseconds'
to purge superfluous troubles.
Fixes: 5c697e5b46ef("ALSA: firewire-lib: remove rx_blocks_for_midi quirk")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Do no send MIDI bytes at the full rate at which FireWire packets happen
to be sent, but restrict them to the actual rate of a real MIDI port.
This is required by the specification, and prevents data loss when the
device's buffer overruns.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are several devices that expect to receive MIDI data only in the
first eight data blocks of a packet. If the driver restricts the data
rate to the allowed rate (as mandated by the specification, but not yet
implemented by this driver), this happens naturally. Therefore, there
is no reason to ever try to use more data packets with any device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although the 't->length' is a big-endian value, it's used without any
conversion. This means that the driver always uses 'length' parameter.
Fixes: 555e8a8f7f14("ALSA: fireworks: Add command/response functionality into hwdep interface")
Reported-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This code tends to use unsigned variables by default and it causes
signedness bugs when we use negative variables for error handling.
The "i" and "j" variables are used to iterated over small positive
values and so they should be type "int". The "len" variable doesn't
*need* to be signed but it should be signed to make the code easier to
read and audit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This code causes a static checker warning:
sound/firewire/oxfw/oxfw.c:46 detect_loud_models()
warn: signedness bug returning '(-2)'
The detect_loud_models() function should return false on falure, so that
we don't try to set up the loud code for hardware that doesn't support
it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This interface is designed for mixer/control application. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds MIDI functionality with an assumption of 'if the device
has MIDI comformant data channels in its stream formation, the device has
one MIDI port'.
When no streams have already started, MIDI functionality starts stream
with current sampling rate.
When MIDI functionality has already starts some streams and PCM
functionality is going to start streams at different sampling rate,
this driver stops streams once and changes sampling rate, then restarts
streams for both PCM/MIDI substreams.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In previous commit, a support for transmitted packets is added. This commit
add a support for capturing PCM samples.
When any streams are already started, this driver should not change sampling
rate of the device, thus this commit also adds a restriction of sampling rate
in this situation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some devices produced by Behringer/Mackie are based on OXFW970/971. This
commit adds support for them. Additionally, this commit changes the way to
name card with some information in config rom.
Ids of some Mackie(Loud) models are not identified, therefore this commit
applies name detection for these models.
The devices support capture/playback of PCM-samples and some of them
supports capture/playback of MIDI messages. These functionalities are
implemented by followed commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In past commit, this driver can keep stream formations for each sampling
rate. So its stream functionality can decide stream formations with given
some parameters.
This commit moves related codes from PCM functionality to stream
functionality. Furthermore, to set stream format correctly, this commit
uses AV/C Stream Format Information command instead of AV/C Input/Output
Plug Signal Format command.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds proc interface to get information about stream
formation. This commit also adds snd_oxfw_stream_get_current_formation()
to get current stream formation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In previous commit, this driver can get to know stream formations at
each supported sampling rates. This commit uses it to make PCM
rules/constraints and obsoletes hard-coded rules/constraints.
For this purpose, this commit adds 'struct snd_oxfw_stream_formation' and
snd_oxfw_stream_parse_format() to parse data channel formation of data
block.
According to datasheet of OXFW970/971, they support 32.0kHz to 196.0kHz.
As long as developers investigate, some devices are confirmed to have
several formats for the same sampling rate.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
OXFW970/971 may supports AV/C Stream Format Information Specification 1.1
Working Draft (Apr 2005, 1394TA). By using this command, drivers can get to know
stream formations which device supports.
This commit adds 'EXTENDED STREAM FORMAT INFORMATION' command. This command
has two subfunctions, 'SINGLE' and 'LIST'. Drivers can use 'SINGLE' subfunction
to know/set current formation of AMDTP stream, Drivers can use 'LIST'
subfunction to know an available formation of AMDTP stream in a certain sampling
rate.
But some devices don't implement the 'LIST' subfunction. So this commit uses
an assumption that 'if they don't implement it, they don't change stream
formation depending on current each sampling rate'. With this assumption, this
driver generates formations for such devices by:
1.getting current formation by SINGLE subfunction
2.getting supported sampling rates
3.applying current formation for all of supported sampling rates
Followed commit implements a parser of this format information.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a preparation for more models. In following commit, members
of 'struct snd_card' related to name becomes to consists of vendor and
model strings in device's config-rom.
Current supported devices also has strings in their config rom, but the
strings are too long to name sound card, thus this driver still keep
hard-coded vendor and model names for them.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a support for MIDI capture/playback
When MIDI substrams already start streaming and PCM substreams are going to
join at different sampling rate, streams are stopped once. Then sampling rate
is changed and streams are restarted.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a support for capturing PCM samples.
When opposite PCM substream is already running, available sampling rate is
limited at current one.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows this driver to handle devices with non SYT-Match
sampling clock source.
When sampling clock source is SYT-Match mode, devices handle
'presentation timestamp' in received packets and generates sampling clock
according to the information. In this case, driver is synchronization master
and must transfer correct value in SYT field of each packets in outgoing
stream, then the outgoing stream is a master stream.
On the other hand, non SYT-Match mode, devices do this. So drivers must pick
up the value in SYT field of incoming packets and use the value for outgoing
stream. Currently firewire-lib module achieve this work.
Furthermore, without SYT-Match and internal clock source, the sampling rate
should be fixed for the other devices connected to the handled device. This
commit add a restriction of sampling rate at this situation.
With these implementations, this driver has no need to set clock source.
This commit remove set function.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds support for AMDTP in-stream. As a result, Dice driver
supports full duplex streams with synchronization.
AMDTP can transfer timestamps in its packets. By handling the timestamp,
devices can synchronize to the other devices or drivers on the same bus.
When Dice chipset is 'enabled', it starts streams with correct settings.
This 'enable' register is global, thus, when a stream is started to run,
an opposite stream can't start unless turning off 'enable'. Therefore
a pair of streams must be running. This causes a loss of CPU usage when
single stream is needed for neither playbacking or capturing.
This commit assumes that playback-only models also have a functionality
to transmit stream for delivering timestamps.
Currently, sampling clock source is restricted to SYT-Match mode. This is
improved in followed commit. I note that at SYT-Match mode, Dice can select
from 4 streams for synchronization but this driver uses the 1st stream only
for simplicity.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Streaming functionality can start streams when rate is given but currently
some codes are in PCM functionality.
This commit changes the way to start stream and add some arrangement
to make it easy to understand the way.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a help for works in followed patches.
And this commit remove 'fw_unit_get()/fw_unit_put()' because these
are called by helper functions in 'snd-firewire-lib'.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Followed commits add much codes. To make the work easy, this commit creates
own directory and move current file to it.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit renames 'firewire-speakers' to 'oxfw' to enhance support for
devices which based on OXFW970/971. A line for MODULE_ALIAS is added.
Additionally, to help for works in followed paches, some members
in private structure are renamed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some developers test this driver, thus it's better to remove its
experimental state.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new functions and some arrangement for PCM restriction.
This arrangement is due to the number of channels which each Dice device has.
I note that minimum number for period becomes 2, instead of 1 because its PCM
functionality has SNDRV_PCM_INFO_BATCH, this means that the driver uses double
(or more) buffering so the minimum number for period should be 2.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a file and move some codes related to proc output.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a file and move some codes related to hwdep functionality.
This interface is designed for mixer/control application. By using hwdep
interface, the application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Additionally, this interface give a way to read Dice notification.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a file and move some codes related to PCM functionality.
Currently PCM playback is supported. PCM capture will be supported in followed
commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a file with some helper functions for streaming, and move some
codes into the file with some arrangements.
Well-known CMP is not used to start/stop streams for Dice chipset. It's
achieved by writing to specific address. We call this way as 'enable'.
When devices are 'enabled', streaming starts in registered isochronous channel.
Some helper functions are already implemented in previous commit.
Basically, the stream is compliant to IEC 61883-6, so-called as AMDTP. But Dice
has a specific quirk, so called-as 'Dual Wire'. This quirk is applied at
176.4/192.0kHz. In this mode, each packet includes double number of events than
number in the specification, and stream runs at a half of sampling rate.
There is another quirk at bus reset. Dice chipset handles drivers' request but
don't re-enable streaming. So stream should be stopped.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a file with some helper functions for transaction, and move
some codes into the file with some arrangements.
For Dice chipset, well-known FCP or AV/C commands are not used to control
devices. It's achieved by read/write transactions into specific addresses.
Dice's address area is split into 5 areas. Each area has its own role. The
offset for each area can be got by reading head of the address area. By
reading these areas, drivers can get to know device status. By writing these
areas, drivers can change device status.
Dice has a specific mechanism called as 'notification'. When device status is
changed, Dice devices tells the event by sending transaction. This notification
is sent to an address which drivers register in advance. But this causes an
issue to drivers.
To handle the notification, drivers need to allocate its own callback function
to the address region in host controller. This region is exclusive. For the
other applications, drivers must give a mechanism to read the received
notification. For this purpose, Dice driver already implements hwdep interface.
Dice chipset doesn't allow drivers to register several addresses. In this
reason, when this driver is applied to a device, the other drivers should
_not_ try to register its own address to the device.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In followed commits, dice driver is split into several files. For easily
managing these files, this commit adds subdirectory and move file into
the directory.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, dice driver supports AMDTP out-stream. In followed commits, AMDTP
in-stream will be supported but current name of members in dice structure
are not propper. This commit renames these members to proper name.
Additionally, for easily distinguishing local symbols from structure tag,
rename dice tag into snd_dice.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The checkpatch.pl generates some warnings due to:
- C99 comment
- a line over 80 characters
- min() for parameters with different types
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Complete missing parameters, correct wrong reference, and add an explaination
about the differences between the latest specification and our implementation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new helper function snd_pcm_stop_xrun() to the standard sequnce
lock/snd_pcm_stop(XRUN)/unlock by a single call, and replace the
existing open codes with this helper.
The function checks the PCM running state to prevent setting the wrong
state, too, for more safety.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_bebob_stream_check_internal_clock() may get an id from
saffirepro_both_clk_src_get (via clk_src->get()) that was uninitialized.
a) make logic in saffirepro_both_clk_src_get explicit
b) test if id used in snd_bebob_stream_check_internal_clock matches array size
[fixed missing signed prefix to *_maps[] by tiwai]
Signed-off-by: Christian Vogel <vogelchr@vogel.cx>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Terratec PHASE 88 rack fw has two registers for source of clock, one is
for internal/external, and another is for wordclock/spdif for external.
When clock source is internal, information in another register has no meaning.
Thus it must be ignored, but current implementation decodes it. This causes
over-indexing reference to labels.
Reported-by: András Murányi <muranyia@gmail.com>
Tested-by: András Murányi <muranyia@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes a failure to open PCM device with -ENOSYS in
Terratec Phase 88.
Terratec Phase 88 has two Selector Function Blocks of AVC Audio subunit
to switch source of clock. One is to switch internal/external for the
source and another is to switch word/spdif for the external clock.
The IDs for these Selector Function Blocks are 9 and 8. But in current
implementation they're 0 and 0.
Reported-by: András Murányi <muranyia@gmail.com>
Tested-by: András Murányi <muranyia@gmail.com>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, one data block transfers one event. In ALSA, the event equals one PCM frame,
hence one data block transfers one PCM frame. But Dice has a quirk at higher sampling rate
(176.4/192.0 kHz) that one data block transfers two PCM frames.
Commit 10550bea44 ("ALSA: dice/firewire-lib: Keep dualwire mode but obsolete
CIP_HI_DUALWIRE") moved some codes related to this quirk into Dice driver. But the commit
forgot to add arrangements for PCM period interrupts and DMA pointer updates. As a result, Dice
driver cannot work correctly at higher sampling rate.
This commit adds 'double_pcm_frames' parameter to amdtp structure for this quirk. When this
parameter is set, PCM period interrupts and DMA pointer updates occur at double speed than in
IEC 61883-6.
Reported-by: Daniel Robbins <drobbins@funtoo.org>
Fixes: 10550bea44 ("ALSA: dice/firewire-lib: Keep dualwire mode but obsolete CIP_HI_DUALWIRE")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # 3.16
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The channel mapping is initialized by amdtp_stream_set_parameters(), however
Dice driver set it before calling this function. Furthermore, the setting is
wrong because the index is the value of array, and vice versa.
This commit moves codes for channel mapping after the function and set it correctly.
Reported-by: Daniel Robbins <drobbins@funtoo.org>
Fixes: 10550bea44 ("ALSA: dice/firewire-lib: Keep dualwire mode but obsolete CIP_HI_DUALWIRE")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # 3.16
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use %d for loop counter and %X for device capabilities. This is a
supplemental patch for Hans Wennborg's patch.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a supplement to my previous patch.
http://mailman.alsa-project.org/pipermail/alsa-devel/2014-July/079190.html
The special_clk_ctl_put() still returns 0 in error handling case. It should
return -EINVAL.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is for correction of my misunderstanding about return value of
.put callback in ALSA Control interface.
According to 'Writing ALSA Driver' (*1), return value of the callback has
three patterns; 1: changed, 0: not changed, an negative value: fatal error.
But I misunderstood that it's boolean; zero or nonzero.
*1: Writing an ALSA Driver (2005, Takashi Iwai)
http://www.alsa-project.org/main/index.php/ALSA_Driver_Documentation
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit uses different labels for control elements of digital input/output
interfaces to correct my misunderstanding about M-Audio Firewire 1814 and
ProjectMix I/O.
According to user manuals for these two models, they have two modes for
digital input; one is S/PDIF in both of optical and coaxial interfaces,
another is ADAT in optical interface only.
But in current implementation, a control element for it reduced labels which
a control element for digital output uses because of my misunderstanding
that optical interface is not available for digital input with S/PDIF mode.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In error handling case, special_clk_ctl_put() returns without unlock_mutex(),
therefore the mutex is still locked. This commit moves mutex_lock() after
the error handling case.
This commit is my solution for this post.
[PATCH -next] ALSA: bebob: Fix missing unlock on error in special_clk_ctl_put()
https://lkml.org/lkml/2014/7/20/12
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently mutex_destroy() is called in module's cleanup function. But after
cleaned up, this mutex is automatically released. So this function call
is meaningless.
[fixed a typo in changelog by tiwai]
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The constants of enum snd_efw_grp_type is for struct snd_efw_phys_grp.type.
But this member is 1 byte. Although the value is between 0x00-0xff, a constant
has 0x10000. This constant is meaningless.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To reverse a pointer for the ring buffer, subtraction by buffer
size is better than assignment to the beginning of the buffer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
All assignment for local variables in these functions are not related to
critical section.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The comment for fcp_avc_transaction() describes it doesn't support this type
of operation. But it was already supported by this commit.
00a7bb81c2
ALSA: firewire-lib: Add support for deferred transaction
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to AM824 in IEC 61883-6:2002, 2 bits in LSB of label for Raw Audio
data means Valid Length Code (VBL). Ths value is:
- b00 for 24 bits sample (label is 0x40)
- b01 for 20 bits sample (label is 0x41)
- b10 for 16 bits sample (label is 0x42)
But current firewire-lib apply 24 bits label for both of 16/24 bits samples.
As long as developers investigate BeBoB/Fireworks/OXFW/Dice, all of them
have a behaviour to ignore the label. They can generate correct sound even
if firewire-lib gives wrong label (i.e. 0xff). On BeBoB, this is not only
for Raw Audio data channel, but also for IEC 60958 Conformant data channel.
So there is little possibility of regression.
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ARRAY_SIZE() was intended here instead of sizeof(). The
"bridgeco_freq_table" array holds integers so the original condition is
never true.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewd-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now snd-firewire-lib supports rawmidi in addition to PCM, thus we need
to give a proper dependency. For fixing and simplification, move the
selections of SND_PCM and SND_RAWMIDI into SND_FIREWIRE_LIB section.
Then each driver doesn't have to select them but only
SND_FIREWIRE_LIB.
Reported-by: Jim Davis <jim.epost@gmail.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There was a typo here so we return directly instead of freeing "hwinfo".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewd-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We checked "err" earlier. These things seem to be left over code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewd-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently bebob driver apply Raw Audio Data channel (in IEC 61883-1:2002,
Multi Bit Linear Audio Data channel in IEC 61883-6:20005) to IEC 60958
Conformant Data channel because both fireworks and bebob based devices
can handle it by ignoring each label.
This patch improves a comment about this.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently mutex_unlock() is called in module's cleanup function. But after
cleaned up, this mutex is automatically released. So this function call
is meaningless.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some variables were declared without static even if they're not referred
to from external files. This commit make them local symbols for better
information-hiding by file unit.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds suffix to register values of each device, to supress 'sparse'
warnings. Additionally, this commit changes offset values with integer literal.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The second argument of snd_efw_command_get_sampling_rate() means sampling
rate and its type is 'unsigned int'. But 'int' variable is passed as parameter.
It's better to apply the same type for the variable as its argument.
Similally, the type of variable for snd_efw_command_get_clock_source() and
avc_bridgeco_get_plug_type() should be the same type as each argument.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Originally, I intent to this argument given with 'struct snd_pcm_runtime.rate'
or params_rate(). They return value of 'unsigned int'. So 'unsigned int' is
better for the type of this argument.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are two modes for Fireworks, IEC 61883 compliant or Windows.
So it's better to use enum type instead of int to express the intension,
even if C language specification defines to handle enum variables as usual
integer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The return value of memdup_user() should be passed to return correct error.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
__be32 value should not be assigned directly to bool value.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit fixes a big for loop count with array. The limitation of loop
count should be calcurated with the number of elements in the array, not
with the number of bytes.
Aditionally, this commit apply the same declaration as a prototype in header
for the array.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In post commit, a quirk of this firmware about transactions is reported.
This commit apply a workaround for this quirk.
They often fail transactions due to gap_count mismatch. This state is changed
by generating bus reset.
The fw_schedule_bus_reset() is an exported symbol in firewire-core. But there
are no header for public. This commit moves its prototype from
drivers/firewire/core.h to include/linux/firewire.h.
This mismatch still affects bus management before generating this bus reset.
It still takes a time to call driver's probe() because transactions are still
often failed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just powering on, these devices below wait to download firmware.
- Firewire Audiophile
- Firewire 410
- Firewire 1814
- ProjectMix I/O
But firmware version 5058 or later, flash memory in the device stores the
firmware. So this driver can enable these devices by sending a certain cue to
load the firmware.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Sakamoto
kbuild test robot
Takashi Iwai
Andrzej Hajda
Yannick Guerrini
Clemens Ladisch
Dan Carpenter
Christian Vogel
Hans Wennborg
Stefan Richter