Add PCI ID and code to support the 5709 Serdes PHY.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some common procedures to handle enabling and disabling 2.5G.
Add some missing code to resolve flow control.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5709 Serdes device uses non-standard MII register offsets. This
re-structuring will make it easier to support 5709 Serdes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the problem of not counting all dropped multicast packets.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed to save the MSI state which will be lost during
suspend.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hot-plug scripts can call bnx2_open() as soon as register_netdev() is
called in bnx2_init_one(). We need to call pci_set_drvdata() and
setup everything before calling register_netdev(). netif_carrier_off()
also needs to be moved to bnx2_open() to avoid race conditions with
the irq.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal PCIE-to-PCIX bridge of the 5708 has the same 40-bit DMA
limitation as some of the tg3 chips. Set dma_mask and persistent DMA
mask to 40-bit to workaround.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device may be in D3hot state and should not allow MII register
access.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 2.5G supported and advertising bit definitions. 2.5G is supported
by the bnx2 driver.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's surround constructs like:
orr r3, r3, #(KERNEL_RAM_PADDR & 0x00f00000)
between .if .endif since (KERNEL_RAM_PADDR & 0x00f00000) is 0 in 99% of
all cases.
Also let's mask PHYS_OFFSET with 0x00f00000 instead of 0x00e00000.
Section mappings are really 1MB not 2MB and the 2MB groupping is
a higher level issue already much better enforced with
#if (PHYS_OFFSET & 0x001fffff)
#error "PHYS_OFFSET must be at an even 2MiB boundary!"
#endif
at the top of the file.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch moves the i.MX UART register descriptions from
include/asm-arm/arch-imx/imx-regs.h to the serial driver itself.
This helps using the driver on other architectures like mx31
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes the position of the netx reset control register
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Various small changes for the Atmel AT91SAM9260-EK and AT91SAM9263-EK
boards.
SAM9260-EK:
- Register I2C device.
SAM9263-EK:
- Add platform_data and register MACB device.
(Patch by Nicolas Ferre)
- Add platform_data and register AC97 device.
(Patch by Nicolas Ferre)
- Register I2C device.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
'type' in the struct expansion_card is only used to indicate
whether this card is an EASI card or not. Therefore, having
it as an enum is wasteful (and introduces additional noise
when we come to remove the enum.) Convert it to a mere flag
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch modifies the startup of kecardd to use kthread_run not a
kernel_thread combination of kernel_thread and daemonize. Making the code
slightly simpler and more maintainable.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add pata_platform device for RiscPC, thereby converting the primary
IDE channel on the machine to PATA.
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Although expansion cards can't do bus-master DMA, subsystems
want to be able to use coherent memory for DMA purposes to
these cards. Therefore, set the coherent DMA mask to allow
such memory to be allocated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow slower serial baud-rates by switching the UART clock from MCK to
MCK/8.
Based on patches by Mike Wolfram and Russell King.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the ADS7846 Touchscreen found on the Atmel
AT91SAM9263-EK board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the ADS7846 Touchscreen found on the Atmel
AT91SAM9261-EK board.
Original patch by Morten Larsen.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define resources, platform_device and device registration functions for
the LCD and AC97 controllers on the AT91SAM9263.
Also update the AT91SAM9261 to use the common atmel_lcdfb driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define and register the remaining peripheral clocks for the AT91
processors.
AT91SAM9261 clocks patch by Ivan Zhakov.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Definitions for Analog-to-Digital Converter (ADC) found on the Atmel
AT91SAM9260 processor.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that do_undefinstr handles kernel and user mode undefined
instruction exceptions it must not assume that interrupts are enabled at
entry.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The tpmi units interface with the SAS controller on iop348.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently the iop3xx platform support code assumes that RedBoot is the
bootloader and has already initialized the ATU. Linux should handle this
initialization for three reasons:
1/ The memory map that RedBoot sets up is not optimal (page_to_dma and
virt_to_phys return different addresses). The effect of this is that using
the dma mapping API for the internal bus dma units generates pci bus
addresses that are incorrect for the internal bus.
2/ Not all iop platforms use RedBoot
3/ If the ATU is already initialized it indicates that the iop is an add-in
card in another host, it does not own the PCI bus, and should not be
re-initialized.
Changelog:
* rather than change nr_controllers to zero, simply do not call
pci_common_init
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate the common push/pull sequences into a few helper functions.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I needed to use this recently to talk to a Cisco server. In my case
I only did SNAT while the Cisco server used a different address for
RTP traffic than the one for SIP. I discovered that nf_nat_sip NATed
the RTP address to the SIP one which was unnecessary but OK. However,
in doing so it did not DNAT the destination address on the RTP traffic
to the Cisco back to the original RTP address.
This patch corrects this by noting down the RTP address and using it
when the expectation fires.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
While porting some changes of the 2.6.21-rc7 pptp/proto_gre conntrack
and nat modules to a 2.4.32 kernel I noticed that the gre_key function
returns a wrong pointer to the GRE key of a version 0 packet thus
corrupting the packet payload.
The intended behaviour for GREv0 packets is to act like
nf_conntrack_proto_generic/nf_nat_proto_unknown so I have ripped the
offending functions (not used anymore) and modified the
nf_nat_proto_gre modules to not touch version 0 (non PPTP) packets.
Signed-off-by: Jorge Boncompte <jorge@dti2.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also accept the --random option for DNAT to allow randomly selecting a
destination port from the given range.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP has a transitional state when SACK is not in use during
which this invariant is temporarily broken. Without SACK,
tcp_clean_rtx_queue does not decrement sacked_out. Therefore
calls to tcp_sync_left_out before sacked_out is again
corrected by tcp_fastretrans_alert can trigger this trap as
sacked_out still has couple of segments that are already out
of window.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust the new netdevice scanning code provided by Patrick McHardy:
(1) Restore the function banner comments that were dropped.
(2) Rather than using an array size of 6 in some places and an array size of
ETH_ALEN in others, pass a pointer instead and pass the array size
through so that we can actually check it.
(3) Do the buffer fill count check before checking the for_primary_ifa
condition again. This permits us to skip that check should maxbufs be
reached before we run out of interfaces.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the large and complicated rtnetlink client by two simple
functions for getting the MAC address for the first ethernet device
and building a list of IPv4 addresses.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __dev_getfirstbyhwtype for callers that don't want a reference but
some data from the device and thus need to take the rtnl anyway.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interface array is not freed on exit.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the user passes in MSG_TRUNC the skb is used after getting freed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we can still receive packets until all references to the
socket are gone, we don't need to kill the CB until that happens.
This also aligns ourselves with the receive queue purging which
happens at that point.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix skbuff.h kernel-doc:
linux-2.6.21-git4//include/linux/skbuff.h:316): No description found for parameter 'transport_header'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete the apparently unused header file net/ipv4/tcp_yeah.h.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make miscellaneous fixes to AFS and AF_RXRPC:
(*) Make AF_RXRPC select KEYS rather than RXKAD or AFS_FS in Kconfig.
(*) Don't use FS_BINARY_MOUNTDATA.
(*) Remove a done 'TODO' item in a comemnt on afs_get_sb().
(*) Don't pass a void * as the page pointer argument of kmap_atomic() as this
breaks on m68k. Patch from Geert Uytterhoeven <geert@linux-m68k.org>.
(*) Use match_*() functions rather than doing my own parsing.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the match_*() functions take a const pointer to the options table
and make strings pointers in the options table const too.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__HAVE_ARCH_ADDR_SET seems unused these days, just get rid of it.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan
Nicolas Pitre
Sascha Hauer
Andrew Victor
Russell King
Eric W. Biederman
Dan Williams
Patrick McHardy
Herbert Xu
Jorge Boncompte
Ilpo Järvinen
David Howells
Randy Dunlap
Robert P. J. Day
Eric Dumazet
Avi Kivity