The API can be used to allocate and free MERAM blocks directly, without
going through ICBs.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
There's no reason to use abstract operation pointers to implement the
MERAM API. Replace them by direct function calls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The MERAM operations meram_register, meram_unregister and meram_update
handle LCDC cache. In preparation for "raw" MERAM allocation, rename
them to more appropriate names.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
For DSI operation in videomode, DISPC logic levels for the signals HSYNC, VSYNC
and DE need to be specified to DSI via the fields VP_HSYNC_POL, VP_VSYNC_POL and
VP_DE_POL in DSI_CTRL registers.
This information is completely internal to DSS as logic levels for the above
signals hold no meaning on the DSI bus. Hence a DSI panel driver should be
totally oblivious of these fields.
Fix the logic levels/polarities in the DISPC and DSI registers to a default
value. This is done by overriding these fields in omap_video_timings struct
filled by the panel driver for DISPC, and use the equivalent default values
when programming DSI_CTRL registers. Also, remove the redundant polarity related
fields in omap_dss_dsi_videomode_data.
Signed-off-by: Archit Taneja <archit@ti.com>
Add a parameter called interlace which tells whether the timings are in
interlaced or progressive mode. This aligns the omap_video_timings struct with
the Xorg modeline configuration.
It also removes the hack needed to write to divide the manager height by 2 if
the connected interface is VENC.
Signed-off-by: Archit Taneja <archit@ti.com>
omap_panel_config contains fields which are finally written to DISPC_POL_FREQo
registers. These are now held by omap_video_timings and are set when the manager
timings are applied.
Remove the omap_panel_config enum, and remove all it's references from panel or
interface drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
Some panel timing related fields are contained in omap_panel_config in the form
of flags. The fields are:
- Hsync logic level
- Vsync logic level
- Data driven on rising/falling edge of pixel clock
- Output enable/Data enable logic level
- HSYNC/VSYNC driven on rising/falling edge of pixel clock
Out of these parameters, Hsync and Vsync logic levels are a part of the timings
in the Xorg modeline configuration. So it makes sense to move the to
omap_video_timings. The rest aren't a part of modeline, but it still makes
sense to move these since they are related to panel timings.
These fields stored in omap_panel_config in dssdev are configured for LCD
panels, and the corresponding LCD managers in the DISPC_POL_FREQo registers.
Add the above fields in omap_video_timings. Represent their state via new enums.
Add these parameters to the omap_video_timings instances in the panel drivers.
Keep the corresponding IVS, IHS, IPC, IEO, RF and ONOFF flags in
omap_panel_config for now. The struct will be removed later.
Signed-off-by: Archit Taneja <archit@ti.com>
Remove omap_lcd_display_type enum
The enum omap_lcd_display_type is used to configure the lcd display type in
DISPC. Remove this enum and always set display type to TFT by creating function
dss_mgr_set_lcd_type_tft().
Signed-off-by: Archit Taneja <archit@ti.com>
Remove OMAP_DSS_LCD_TFT as a omap_panel_config flag.
We don't support passive matrix displays any more. Remove this flag from all the
panel drivers.
Force the display_type to OMAP_DSS_LCD_DISPLAY_TFT in the interface drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
The support for LCD3 manager has been added into the manager module. LCD3 panel
has registers as DISPC_CONTROL3 and DISPC_CONFIG3 just like those in LCD and
LCD2 panels. These registers control the Display Controller (DISPC) module for
LCD3 output. The three LCDs support Display Serial Interface (DSI), Remote Frame
Buffer Interface (RFBI) and Parallel CMOS Output Interface (DPI). These LCDs can
be connected through parallel output interface using DISPC and RFBI or DPI. For
serial interface DSS uses DSI.
The LCD3 panel, just like LCD and LCD2 panels, has a clock switch in DSS_CTRL
register which has been enabled. The clock switch chooses between DSS_CLK and
DPLL_DSI1_C_CLK1 as source for LCD3_CLK. New IRQs as DISPC_IRQ_VSYNC3,
DISPC_IRQ_FRAMEDONE3, DISPC_IRQ_ACBIAS_COUNT_STAT3 and DISPC_IRQ_SYNC_LOST3 have
been added specific to the new manager.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP5 Display Subsystem (DSS) architecture comes with a additional LCD3 channel
with its own dedicated overlay manager. The current patch adds LCD3 channel and
basic register support for LCD3 channel. It adds register addresses for various
Display Controller (DISPC) registers like DISPC_DEFAULT_COLOR, DISPC_TIMING_H,
DISPC_DIVISORo, etc.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have two almost the same enums: omap_channel and
omap_dss_overlay_managers. omap_channel is used almost everywhere, and
omap_channel assigns explicit values to the enum values which are needed
for proper operation.
omap_dss_overlay_managers is only used in one place, so it's easy to
remove it, which is what this patch does.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It includes:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=tmIU
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
* tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits)
video: bfin_adv7393fb: Fix cleanup code
video: exynos_dp: reduce delay time when configuring video setting
video: exynos_dp: move sw reset prioir to enabling sw defined function
video: exynos_dp: use devm_ functions
fb: handle NULL pointers in framebuffer release
OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request
OMAPDSS: Apply VENC timings even if panel is disabled
OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
OMAPDSS: DISPC: Support rotation through TILER
OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n
OMAPFB: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods
OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers
video: exynos mipi dsi: support reverse panel type
video: exynos mipi dsi: Properly interpret the interrupt source flags
video: exynos mipi dsi: Avoid races in probe()
...
Lots of normal development commits, but perhaps most notable changes are:
* HDMI rework to properly decouple the HDMI audio part from the HDMI video part.
* Restructure omapdss core driver so that it's possible to implement device
tree support. This included changing how platform data is passed to the
drivers, changing display device registration and improving the panel driver's
ability to configure the underlying video output interface.
* Basic support for DSI packet interleaving
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=I8Se
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.5' of git://github.com/tomba/linux into fbdev-next
Omapdss driver changes for 3.5 merge window.
Lots of normal development commits, but perhaps most notable changes are:
* HDMI rework to properly decouple the HDMI audio part from the HDMI video part.
* Restructure omapdss core driver so that it's possible to implement device
tree support. This included changing how platform data is passed to the
drivers, changing display device registration and improving the panel driver's
ability to configure the underlying video output interface.
* Basic support for DSI packet interleaving
These cleanups are basically all over the place. The idea is to collect
changes with minimal impact but large number of changes so we can avoid
them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Hcjs
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull first batch of arm-soc cleanups from Olof Johansson:
"These cleanups are basically all over the place. The idea is to
collect changes with minimal impact but large number of changes so we
can avoid them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases."
Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Dove: Fix Section mismatch warnings
ARM: orion5x: ts78xx debugging changes
ARM: orion5x: remove PM dependency from ts78xx
ARM: orion5x: ts78xx fix NAND resource off by one
ARM: orion5x: ts78xx whitespace cleanups
Orion5x: Fix Section mismatch warnings
Orion5x: Fix warning: struct pci_dev declared inside paramter list
ARM: clps711x: Combine header files into one for clps711x-targets
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
...
TILER is a block in OMAP4's DMM which lets DSS fetch frames in a rotated manner.
Physical memory can be mapped to a portion of OMAP's system address space called
TILER address space. The TILER address space is split into 8 views. Each view
represents a rotated or mirrored form of the mapped physical memory. When a
DISPC overlay's base address is programmed to one of these views, the TILER
fetches the pixels according to the orientation of the view. A view is further
split into 4 containers, each container holds elements of a particular size.
Rotation can be achieved at the granularity of elements in the container. For
more information on TILER, refer to the Memory Subsytem section in OMAP4 TRM.
Rotation type TILER has been added which is used to exploit the capabilities of
these 8 views for performing various rotations.
When fetching from addresses mapped to TILER space, the DISPC DMA can fetch
pixels in either 1D or 2D bursts. The fetch depends on which TILER container we
are accessing. Accessing 8, 16 and 32 bit sized containers requires 2D bursts,
and page mode sized containers require 1D bursts.
The DSS2 user is expected to provide the Tiler address of the view that it is
interested in. This is passed to the paddr and p_uv_addr parameters in
omap_overlay_info. It is also expected to provide the stride value based on the
view's orientation and container type, this should be passed to the screen_width
parameter of omap_overlay_info. In calc_tiler_rotation_offset screen_width is
used to calculate the required row_inc for DISPC. x_predecim and y_predecim are
also used to calculate row_inc and pix_inc thereby adding predecimation support
for TILER.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Latest SuperH HDMI uses not only HDMI Core Register (HTOP0)
but also HDMI Control Register (HTOP1).
This patch adds HDMI Control Register support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Latest SuperH HDMI allows 32bit access only.
But the data is 8bit. So, we can keep compatibility by switching 8/32 bit access.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
There exist several display technologies and standards that support audio as
well. Hence, it is relevant to update the DSS device driver to provide an audio
interface that may be used by an audio driver or any other driver interested in
the functionality.
The audio_enable function is intended to prepare the relevant
IP for playback (e.g., enabling an audio FIFO, taking in/out of reset
some IP, enabling companion chips, etc). It is intended to be called before
audio_start. The audio_disable function performs the reverse operation and is
intended to be called after audio_stop.
While a given DSS device driver may support audio, it is possible that for
certain configurations audio is not supported (e.g., an HDMI display using a
VESA video timing). The audio_supported function is intended to query whether
the current configuration of the display supports audio.
The audio_config function is intended to configure all the relevant audio
parameters of the display. In order to make the function independent of any
specific DSS device driver, a struct omap_dss_audio is defined. Its purpose
is to contain all the required parameters for audio configuration. At the
moment, such structure contains pointers to IEC-60958 channel status word and
CEA-861 audio infoframe structures. This should be enough to support HDMI and
DisplayPort, as both are based on CEA-861 and IEC-60958. The omap_dss_audio
structure may be extended in the future if required.
The audio_enable/disable, audio_config and audio_supported functions could be
implemented as functions that may sleep. Hence, they should not be called
while holding a spinlock or a readlock.
The audio_start/audio_stop function is intended to effectively start/stop audio
playback after the configuration has taken place. These functions are designed
to be used in an atomic context. Hence, audio_start should return quickly and be
called only after all the needed resources for audio playback (audio FIFOs,
DMA channels, companion chips, etc) have been enabled to begin data transfers.
audio_stop is designed to only stop the audio transfers. The resources used
for playback are released using audio_disable.
A new enum omap_dss_audio_state is introduced to help the implementations of
the interface to keep track of the audio state. The initial state is _DISABLED;
then, the state transitions to _CONFIGURED, and then, when it is ready to
play audio, to _ENABLED. The state _PLAYING is used when the audio is being
rendered.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
The omapdss pdata handling is a mess. This is more evident when trying
to use device tree for DSS, as we don't have platform data anymore in
that case. This patch cleans the pdata handling by:
- Remove struct omap_display_platform_data. It was used just as a
wrapper for struct omap_dss_board_info.
- Pass the platform data only to omapdss device. The drivers for omap
dss hwmods do not need the platform data. This should also work better
for DT, as we can create omapdss device programmatically in generic omap
boot code, and thus we can pass the pdata to it.
- Create dss functions for get_ctx_loss_count and dsi_enable/disable_pads
that the dss hwmod drivers can call.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Conflicts:
drivers/video/omap2/displays/panel-taal.c
Merge OMAP DSS related board file changes. The branch will also be
merged through linux-omap tree to solve conflicts.
In preparation for device tree, this patch changes how the DSI pins are
configured. The current configuration method is only doable with board
files and the configuration data is OMAP specific.
This patch moves the configuration data to the panel's platform data,
and the data can easily be given via DT in the future. The configuration
data format is also changed to a generic one which should be suitable
for all platforms.
The new format is an array of pin numbers, where the array items start
from clock + and -, then data1 + and -, and so on. For example:
{
0, // pin num for clock lane +
1, // pin num for clock lane -
2, // pin num for data1 lane +
3, // pin num for data1 lane -
...
}
The pin numbers are translated by the DSI driver and used to configure
the hardware appropriately.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Now that the tfp410 driver has been renamed in the code, this patch
finishes the renaming by renaming the files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The driver for the TFP410 DPI-to-DVI chip was named quite badly as "DVI
panel driver". This patch renames the code to use tfp410 name for the
driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Now that the panel-dvi driver handles the PD (power-down) GPIO, we can
remove the custom PD handling from the board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The driver for the TFP410 chip should handle the power-down signal of
the chip, instead of the current way of handling it in the board files.
This patch adds power_down_gpio into the device's platform data, and
adds the necessary code in the driver to request and handle the GPIO.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch fixes max loop count in EQ(Channel Equalization) sequence
of link training. According to DP(displayport) specification,
the max loop count in this sequence should be 5.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The AUO-K190X controllers share a very similar set of commands and
can therefore also share most of the driver code.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
With this we can eliminate some duplicate code in panel drivers.
Also lgphilips-lb035q02, nec-nl8048hl11-01b, picodlp and
tpo-td043mtea1 gain support of reading timings over sysfs.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss driver needs to use the omap_pm_set_min_bus_tput(), so add a new
entry for that in omapdss's platform data, and set it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@ti.com>
For now, it just contains the hack for cirrusfb on Amiga, which is moved
out of <video/vga.h> with some slight modifications (use raw_*() instead of
z_*(), which are defined on all m68k platforms).
This makes it safe to include <video/vga.h> in all contexts. Before it
could fail to compile with
include/video/vga.h: In function ‘vga_mm_r’:
include/video/vga.h:242: error: implicit declaration of function ‘z_readb’
include/video/vga.h: In function ‘vga_mm_w’:
include/video/vga.h:247: error: implicit declaration of function ‘z_writeb’
include/video/vga.h: In function ‘vga_mm_w_fast’:
include/video/vga.h:253: error: implicit declaration of function ‘z_writew’
or
include/video/vga.h:23:21: error: asm/vga.h: No such file or directory
depending on the value of CONFIG_AMIGA.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Pull ARM platform updates from Russell King:
"This covers platform stuff for platforms I have a direct interest in
(iow, I have the hardware). Essentially:
- as we no longer support any other Acorn platforms other than RiscPC
anymore, we can collect all that code into mach-rpc.
- convert Acorn expansion card stuff to use IRQ allocation functions,
and get rid of NO_IRQ from there.
- cleanups to the ebsa110 platform to move some private stuff out of
its header files.
- large amount of SA11x0 updates:
- conversion of private DMA implementation to DMA engine support
(this actually gives us greater flexibility in drivers over the old
API.)
- re-worked ucb1x00 updates - convert to genirq, remove sa11x0
dependencies, fix various minor issues
- move platform specific sa11x0 framebuffer data into platform files
in arch/arm instead of keeping this in the driver itself
- update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
for SIR transmissions as well as FIR
- rework sa1111 support for genirq, and irq allocation
- fix sa1111 IRQ support so it works again
- use sparse IRQ support
After this, I have one more pull request remaining from my current
set, which I think is going to be the most problematical as it
generates 8 conflicts."
Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.
* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
ARM: 7343/1: sa11x0: convert to sparse IRQ
ARM: 7342/2: sa1100: prepare for sparse irq conversion
ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
ARM: sa11x0: remove unused DMA controller definitions
ARM: sa11x0: remove old SoC private DMA driver
USB: sa1111: add hcd .reset method
USB: sa1111: add OHCI shutdown methods
USB: sa1111: reorganize ohci-sa1111.c
USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
USB: sa1111: sparse and checkpatch cleanups
ARM: sa11x0: don't static map sa1111
ARM: sa1111: use dev_err() rather than printk()
ARM: sa1111: cleanup sub-device registration and unregistration
ARM: sa1111: only setup DMA for DMA capable devices
ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
ARM: sa1111: delete unused physical GPIO register definitions
...
sh_mipi uses some clocks, but the method of setup depends on CPU.
Current SuperH (like sh73a0) can control all of these clocks
by CPG (Clock Pulse Generator).
It means we can control it by clock framework only.
But on sh7372, it needs CPG settings AND sh_mipi PHYCTRL::PLLDS,
and only sh7372 has PHYCTRL::PLLDS.
But on current sh_mipi driver, PHYCTRL::PLLDS of sh7372 was
overwrote since the callback timing of clock setting was changed
by c2658b70f0
(fbdev: sh_mipi_dsi: fixup setup timing of sh_mipi_setup()).
To solve this issue, this patch adds extra .phyctrl.
This patch adds detail explanation for unclear mipi settings
and fixup wrong PHYCTRL::PLLDS value for ap4evb (0xb -> 0x6).
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The meram_register(), meram_unregister() and meram_update() operations
check that the pointers they get from the caller are not NULL. Those
checks can be remove, as the caller already ensures that the pointers
are valid.
The platform sanity checks can also be removed, as the operations can't
be accessed without valid platform data anyway.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Remove the RGB or Y/C base address update from the meram_register()
operation, as this belongs to the meram_update() operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of copying the whole platform data structure to struct
sh_mobile_lcdc_chan, store a const pointer to the channel platform data.
MERAM configuration information needs to be changed at runtime, so copy
it to struct sh_mobile_lcdc_chan.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of manually specifying the ICBs to use in platform data,
allocate them automatically at runtime. The range of reserved ICBs (for
instance to be used through UIO), if any, is passed in the platform data
reserved_icbs field as a bitmask.
The MERAM registration function now returns a pointer to an opaque MERAM
object, which is passed to the update and unregistration functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of requiring the users to hardcode MERAM allocation in platform
data, allocate blocks at runtime using genalloc.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The new structure stores ICB parameters for ICBs.
Instead of modifying the struct sh_mobile_meram_cfg instances passed by
callers, store the ICB parameters internally and make the public API
take const pointers to sh_mobile_meram_cfg.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Many variables, such as loop counters, sizes and offsets, should be
unsigned integers. Make them so.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The structure describe ICB configuration, no ICB objects themselves.
Rename it to sh_mobile_meram_icb_cfg in preparation for the addition of
an ICB structure.
All the structure fields are unsigned integers, make them so.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The struct sh_mobile_lcdc_chan_cfg platform data contains a list of
video modes. Name the lcd_cfg and num_cfg fields to reflect that they
describe video modes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Pass a pointer to the transmitter device through platform data, retrieve
the corresponding sh_mobile_lcdc_entity structure in the probe method
and call the transmitter display_on/off methods directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Fix race conditions with unplug/replug behavior, in particular
take care not to hold up USB probe/disconnect for long-running
framebuffer operations and rely on usb to handle teardown.
Fix for kernel panic reported with new F17 multiseat support.
Reported-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Now that we have platform data contained within the individual board
code, we can get rid of the global function pointers, placing them
inside the platform data instead.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the LCD data structures to an include file which can be shared
with the board code in arch/arm/mach-sa1100.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Samsung EXYNOS SoC such Exynos5 has DP controller and embedded DP
panel can be used. This patch supports DP driver based on Samsung
EXYNOS SoC chip.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Samsung S5PC210 and EXYNOS SoC platform has MIPI-DSI controller and
MIPI-DSI based LCD Panel could be used with it. This patch supports
MIPI-DSI driver based Samsung SoC chip.
LCD panel driver based MIPI-DSI should be registered to MIPI-DSI driver at
machine code and LCD panel driver specific function registered to
mipi_dsim_ddi structure at lcd panel init function called system init. In
the MIPI-DSI driver, find lcd panel driver by using registered lcd panel
name, and then initialize lcd panel driver.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
It includes:
- a compile fix for fsl-diu-fb
- a fix for a suspend/resume issue in atmel_lcdfb
- a fix for a suspend/resume issue in OMAP
- a workaround for a hardware bug to avoid physical damage in OMAP
- a really trivial dead code removal in intelfb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=2uP4
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6
fbdev fixes for 3.3
It includes:
- compile fix for fsl-diu-fb
- fix for a suspend/resume issue in atmel_lcdfb
- fix for a suspend/resume issue in OMAP
- workaround for a hardware bug to avoid physical damage in OMAP
- really trivial dead code removal in intelfb
* tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6:
atmel_lcdfb: fix usage of CONTRAST_CTR in suspend/resume
intelfb: remove some dead code
drivers/video: compile fixes for fsl-diu-fb.c
OMAPDSS: HDMI: PHY burnout fix
OMAP: 4430SDP/Panda: add HDMI HPD gpio
OMAP: 4430SDP/Panda: setup HDMI GPIO muxes
OMAPDSS: remove wrong HDMI HPD muxing
OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPD
OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpios
OMAPDSS: use sync versions of pm_runtime_put
A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board
if the HDMI PHY is kept powered on when the cable is not connected.
This patch solves the problem by adding hot-plug-detection into the HDMI
IP driver. This is not a real HPD support in the sense that nobody else
than the IP driver gets to know about the HPD events, but is only meant
to fix the HW bug.
The strategy is simple: If the display device is turned off by the user,
the PHY power is set to OFF. When the display device is turned on by the
user, the PHY power is set either to LDOON or TXON, depending on whether
the HDMI cable is connected.
The reason to avoid PHY OFF when the display device is on, but the cable
is disconnected, is that when the PHY is turned OFF, the HDMI IP is not
"ticking" and thus the DISPC does not receive pixel clock from the HDMI
IP. This would, for example, prevent any VSYNCs from happening, and
would thus affect the users of omapdss. By using LDOON when the cable is
disconnected we'll avoid the HW bug, but keep the HDMI working as usual
from the user's point of view.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
* 'for-next' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: Split trivial #if defined(__KERNEL__) && X conditionals
UAPI: Don't have a #elif clause in a __KERNEL__ guard in linux/soundcard.h
UAPI: Fix AHZ multiple inclusion when __KERNEL__ is removed
UAPI: Make linux/patchkey.h easier to parse
UAPI: Fix nested __KERNEL__ guards in video/edid.h
UAPI: Alter the S390 asm include guards to be recognisable by the UAPI splitter
UAPI: Guard linux/cuda.h
UAPI: Guard linux/pmu.h
UAPI: Guard linux/isdn_divertif.h
UAPI: Guard linux/sound.h
UAPI: Rearrange definition of HZ in asm-generic/param.h
UAPI: Make FRV use asm-generic/param.h
UAPI: Make M32R use asm-generic/param.h
UAPI: Make MN10300 use asm-generic/param.h
UAPI: elf_read_implies_exec() is a kernel-only feature - so hide from userspace
UAPI: Don't include linux/compat.h in sparc's asm/siginfo.h
UAPI: Fix arch/mips/include/asm/Kbuild to have separate header-y lines
Disables the internal pull resistor for SDA and SCL which are enabled by
default, as there are external pull up's in 4460 and 4430 ES2.3
SDP, Blaze and Panda Boards, It is done to avoid the EDID read failure.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move duplicate HDMI mux_init code from omap4 and panda board file
to display file.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_overlay_manager contains device_changed field, which no longer has
any use. So remove the field and the few places where it is touched.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Setting overlay's output channel is currently handled at the same time
as other overlay attributes. This is not right, as the normal attributes
should only affect one overlay and manager, but changing the channel
affects two managers.
This patch moves the channel field into the "extra_info" set, handled
together with enabled-status.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
struct omap_overlayr contains info and info_dirty fields, both of which
should be internal to apply.c.
This patch moves those fields into ovl_priv data, and names them
user_info and user_info_dirty.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
struct omap_overlay_manager contains info and info_dirty fields, both of
which should be internal to apply.c.
This patch moves those fields into mgr_priv data, and names them
user_info and user_info_dirty.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Overlays are currently enabled and disabled with a boolean in the struct
omap_overlay_info. The overlay info is set with ovl->set_overlay_info(),
and made into use with mgr->apply().
This doesn't work properly, as the enable/disable status may affect also
other overlays, for example when using fifo-merge. Thus the enabling and
disabling of the overlay needs to be done outside the normal overlay
configuration.
This patch achieves that by doing the following things:
1) Add function pointers to struct omap_overlay: enable(), disable() and
is_enabled(). These are used to do the obvious. The functions may block.
2) Move the "enabled" field from struct omap_overlay to ovl_priv_data.
3) Add a new route for settings to be applied to the HW, called
"extra_info". The status of the normal info and extra_info are tracked
separately.
The point here is to allow the normal info to be changed and
applied in non-blocking matter, whereas the extra_info can only be
changed when holding the mutex. This makes it possible to, for example,
set the overlay enable flag, apply it, and wait until the HW has taken
the flag into use.
This is not possible if the enable flag would be in the normal info, as
a new value for the flag could be set at any time from the users of
omapdss.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
struct omap_overlay_manager contains "enabled"-field, used to track if
the manager is enabled or not. This field should be internal to apply.c.
This patch moves the field to mgr_priv_data, and applies the necessary
locking when accessing the field.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current code uses dsi_video_mode_enable/disable functions to
enable/disable DISPC output for video mode displays. For command mode
displays we have no notion in the DISPC side of whether the panel is
enabled, except when a dss_mgr_start_update() call is made.
However, to properly maintain the DISPC state in apply.c, we need to
know if a manager used for a manual update display is currently in use.
This patch achieves that by changing dsi_video_mode_enable/disable to
dsi_enable/disable_video_output, which is called by both video and
command mode displays. For video mode displays it starts the actual
pixel stream, as it did before. For command mode displays it doesn't do
anything else than mark that the manager is currently in use.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Current way of handling overlay-manager links is a bit strange: each
manager has a static array, containing pointers to all the overlays
(even those used by other managers). The overlays contain a pointer to
the manager being used.
This patch makes the system a bit saner: each manager has a linked list
of overlays, and only the overlays linked to that manager are in the
list.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Overlay managers are stored in a linked list. There's no need for this
list, as an array would do just as fine.
This patch changes the code to use an array for overlay managers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add "enabled" field to struct omap_overlay_manager, which tells if the
output is enabled or not. This will be used in apply.c in the following
patches.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_overlay_manager struct contains enable() and disable() functions.
However, these are only meant to be used from inside omapdss, and thus
it's bad to expose the functions.
This patch adds dss_mgr_enable() and dss_mgr_disable() functions to
apply.c, which handle enabling and disabling the output.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Partial update for manual update displays has never worked quite well:
* The HW has limitations on the update area, and the x and width need to
be even.
* Showing a part of a scaled overlay causes artifacts.
* Makes the management of dispc very complex
Considering the above points and the fact that partial update is not
used anywhere, this and the following patches remove the partial update
support. This will greatly simplify the following re-write of the apply
mechanism to get proper locking and additional features like fifo-merge.
This patch removes the partial update from the dsi.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
SH MIPI manual explains the calculation method of HBP/HFP.
it is based on HSbyteCLK settings.
SH73a0 chip can use HS6divCLK/HS4divCLK for it.
This patch has compatibility to SH7372 mipi
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Dot clock of SH MIPI are depends on each platform board.
This patch adds set_dot_clock() function for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
SH MIPI DSI can use 0-4 lane
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds a custom DSS reset function used on OMAPs from OMAP2
forward.
The function doesn't actually do a reset, it only waits for the reset to
complete. The reason for this is that on OMAP4 there is no possibility
to do a SW reset, and on OMAP2/3 doing a SW reset for dss_core resets
all the other DSS modules also, thus breaking the HWMOD model where
every DSS module is handled independently.
This fixes the problem with DSS reset on OMAP4, caused by the fact that
because there's no SW reset for dss_core on OMAP4, the HWMOD framework
doesn't try to reset dss_core and thus the DSS clocks were never enabled
at the same time. This causes causes the HWMOD reset to fail for
dss_dispc and dss_rfbi.
The common reset function will also allow us to fix another problem in
the future: before doing a reset we need to disable DSS outputs, which
are in some cases enabled by the bootloader, as otherwise DSS HW seems
to get more or less stuck, requiring a power reset to recover.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: modified to build arch/arm/mach-omap2/display.o
unconditionally to avoid an error when !CONFIG_OMAP2_DSS]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add zorder support on OMAP4, this feature allows deciding the visibility order
of the overlays based on the zorder value provided as an overlay info parameter
or a sysfs attribute of the overlay object.
Use the overlay cap OMAP_DSS_OVL_CAP_ZORDER to determine whether zorder is
supported for the overlay or not. Use dss feature FEAT_ALPHA_FREE_ZORDER
if the caps are not available.
Ensure that all overlays that are enabled and connected to the same manager
have different zorders. Swapping zorders of 2 enabled overlays currently
requires disabling one of the overlays.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for VIDEO3 pipeline on OMAP4:
- Add VIDEO3 pipeline information in dss_features and omapdss.h
- Add VIDEO3 pipeline register coefficients in dispc.h
- Create a new overlay structure corresponding to VIDEO3.
- Make changes in dispc.c for VIDEO3
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On OMAP3, in order to enable alpha blending for LCD and TV managers, we needed
to set LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits in DISPC_CONFIG. On
OMAP4, alpha blending is always enabled by default, if the above bits are set,
we switch to an OMAP3 compatibility mode where the zorder values in the pipeline
attribute registers are ignored and a fixed priority is configured.
Rename the manager_info member "alpha_enabled" to "partial_alpha_enabled" for
more clarity. Introduce two dss_features FEAT_ALPHA_FIXED_ZORDER and
FEAT_ALPHA_FREE_ZORDER which represent OMAP3-alpha compatibility mode and OMAP4
alpha mode respectively. Introduce an overlay cap for ZORDER. The DSS2 user is
expected to check for the ZORDER cap, if an overlay doesn't have this cap, the
user is expected to set the parameter partial_alpha_enabled. If the overlay has
ZORDER cap, the DSS2 user can assume that alpha blending is already enabled.
Don't support OMAP3 compatibility mode for now. Trying to read/write to
alpha_blending_enabled sysfs attribute issues a warning for OMAP4 and does not
set the LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits.
Change alpha_enabled to partial_alpha_enabled in the omap_vout driver. Use
overlay cap "OMAP_DSS_OVL_CAP_GLOBAL_ALPHA" to check if overlay supports alpha
blending or not. Replace this with checks for VIDEO1 pipeline.
Cc: linux-media@vger.kernel.org
Cc: Lajos Molnar <molnar@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
overlay_info struct, used to configure overlays, currently includes both
physical and virtual addresses for the pixels. The vaddr was added to
support more exotic configurations where CPU would be used to update a
display, but it is not currently used and there has been no interest in
the feature. Using CPU to update a screen is also less interesting now
that OMAP4 has two LCD outputs.
This patch removes the vaddr field, and modifies the users of omapdss
accordingly. This makes the use of omapdss a bit simpler, as the user
doesn't need to think if it needs to give the vaddr.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This is a driver for N800's display, ported from the old omapfb. This is
a slightly lighter version of the driver as not all features of the old
driver can be ported without big changes to DSS2, and also because some
of the HW features used in the old driver are unclear (e.g. the power
management part).
That said, the new driver works fine for basic use.
Architecturally the driver is not as neat as it could be. N800's display
HW consists of a display buffer chip and a panel, and ideally they would
be represented by separate, independent drivers. This is not currently
possible, and this driver contains both buffer chip and panel driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Taal panel driver supports two kinds of backlight control: 1) using DSI
commands sent to the panel to control the backlight, 2) calling function
pointers going to the board file to control the backlight.
The second option is a bit hacky, and will no longer be needed when the
PWM driver supports the backlight features. After that we can use the
standard PWM backlight driver.
This patch removes the second backlight control mechanism, and adds a
boolean field, use_dsi_backlight, to nokia_dsi_panel_data which the
board file can use to inform whether the panel driver should use DSI
commands to control the backlight.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have currently panel-generic-dpi driver, which is a combined driver
for dummy panels and also for DVI output.
The aim is to split the panel-generic-dpi into two, one for fixed size
dummy panels connected via DPI, and the other (this) for variable
resolution output which supports DDC channel (in practice a DVI framer
chip connected to DPI output).
Original i2c code by: Ricardo Salveti de Araujo
<ricardo.salveti@canonical.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
regn divider is currently programmed to the registers without change,
but when calculating clock frequencies it is used as regn+1.
To make this similar to how DSI handles the dividers this patch changes
the regn value to be used as such for calculations, but the value
programmed to registers is regn-1.
This simplifies the clock frequency calculations, makes it similar to
DSI, and also allows us to use regn value 0 as undefined.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add initial support for DSI video mode panels:
- Add a new structure omap_dss_dsi_videomode_data in the member "panel" in
omap_dss_device struct. This allows panel driver to configure dsi video_mode
specific parameters.
- Configure basic DSI video mode timing parameters: HBP, HFP, HSA, VBP, VFP, VSA,
TL and VACT.
- Configure DSI protocol engine registers for video_mode support.
- Introduce functions dsi_video_mode_enable() and dsi_video_mode_disable() which
enable/disable video mode for a given virtual channel and a given pixel format
type.
Things left for later
- Add functions to check for errors in video mode timings provided by panel.
- Configure timing registers required for command mode interleaving.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, DSI pixel info is only represented by the pixel size in bits using
the pixel_size parameter in omap_dss_device struct's ctrl member.
This is not sufficient information for DSI video mode usage, as two of the
supported formats(RGB666 loosely packed, and RGB888) have the same pixel
container size, but different data_type values for the video mode packet header.
Create enum "omap_dss_dsi_pixel_format" which describes the pixel data format
the panel is configured for. Create helper function dsi_get_pixel_size() which
returns the pixel size of the given pixel format.
Modify functions omapdss_default_get_recommended_bpp() and dss_use_replication()
to use dsi_get_pixel_size().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Introduce read functions which use generic Processor-to-Peripheral
transaction types. These are needed by some devices which may not support
corresponding DCS commands.
Add function dsi_vc_generic_send_read_request() which can send
a short packet with 0, 1 or 2 bytes of request data and the corresponding
generic data type.
Rename function dsi_vc_dcs_read_rx_fifo() to dsi_vc_read_rx_fifo() and modify
it to take the enum "dss_dsi_content_type" as an argument to use either DCS
or GENERIC Peripheral-to-Processor transaction types while parsing data read
from the device.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove functions dsi_vc_dcs_read_1() and dsi_vc_dcs_read_2(), these are used
when the panel is expected to return 1 and 2 bytes respecitvely. This was manily
used for debugging purposes. These functions should be implemented in the panel
driver if needed.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Intoduce enum "dss_dsi_content_type" to differentiate between DCS and generic
content types.
Introduce short and long packet write functions which use generic
Processor-to-Peripheral transaction types. These are needed by some devices
which may not support corresponding DCS commands. Create common write functions
which allow code reuse between DCS and generic write functions.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Create an enum for DSI operation modes, use this to set the capabilities of the
device in dsi_init_display().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add OMAP_DSS_OVL_CAP_GLOBAL_ALPHA and OMAP_DSS_OVL_CAP_PRE_MULT_ALPHA to
overlay capabilities. Use these instead of FEAT_GLOBAL_ALPHA,
FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA in code.
Remove FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA which are no
longer used. FEAT_GLOBAL_ALPHA is still used to decide if the HW has
global alpha register.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
Remove support for non-DISPC overlays and overlay managers.
The support to possibly have non-DISPC overlays and managers was made to
make it possible to use CPU and/or sDMA to update RFBI or DSI command
mode displays. It is ok to remove the support, because:
- No one has used the feature.
- Display update without DISPC is very slow, so it is debatable if the
update would even be usable.
- Removal cleans up code.
- If such a feature is needed later, it is better implemented outside
omapdss driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
Currently when changing the manager of an overlay, set_manager() directly
calls dispc to set the overlay's destination.
Change this to be more in line with other overlay configurations, and
this will also remove the need to have dispc clocks enabled when calling
set_manager().
A new field is added to overlay struct, "manager_changed". This is
similar to "display_changed" field in manager struct, and is used to
inform apply that the manager has changed and thus write to the
registers is needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dsi_mux_pads() needs to know about the DSI HW module and the DSI lanes
used. Split the function into two, enable and disable, which take
necessary arguments, and add empty implementations for both.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
PicoDLP is a micro projector from TI.
DLP used in OMAP4 is dpp2600 (DLP Pico Projector) The DLP requires
commands to be sent over i2c for configurations. To know more about
dpp2600 commands please visit:
https://focus.ti.com/myti/docs/extranet.tsp?sectionId=403
The picodlp module consists of a dss driver and an i2c_client.
To know more please visit:
http://www.omappedia.org/wiki/PicoDLP_projector_guide
Based on original design from Mythri P K <mythripk@ti.com>
Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Mythri P K <mythripk@ti.com>
[tomi.valkeinen@ti.com: squashed commits]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fixes earlier problems where monitor would not return from blank
Test with any DisplayLink-based USB 2.0 graphics adapter
sudo nano /sys/class/graphics/fb?/blank
and write out single digit FB_BLANK_* code from include/linux/fb.h
Supports on (0), blank (1), suspend (2,3), powerdown (4)
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Instead of hardcoding register values through the driver, define macros
for individual register bits using the register name and the bit name,
and use the macros.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The function to get device's context loss count has changed from
omap_pm_get_last_off_on_transaction_id() to
omap_pm_get_dev_context_loss_count()
Change name of the function pointer in omapdss.h accordingly, and use
the term "context loss count" instead of "context id" in the code.
Restructure the context loss count functions to handle errors properly,
and ensure that context is always considered lost if an error happens.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add Color Phase Rotation (CPR) support and sysfs files to enable CPR and
to set the CPR coefficient matrix.
CPR is enabled via manager?/cpr_enable file, and the coefficient matrix
is set via manager?/cpr_coef file. The values in cpr_coef are in the
following order:
RR RG RB GR GG GB BR BG BB
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove the whole update_mode stuff from omapdss driver. If automatic
update for manual update displays is needed, it's better implemented in
higher layers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss.h included platform_device.h and atomic.h, neither of which is
needed by omapdss.h. Remove those includes from omapdss.h, and fix the
affected .c files which did not include platform_device.h even though
they should.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Since the NV24 framebuffer has a CbCr plane that is twice as wide
as the Y plane, it needs to be handled as a special case.
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Based on the patch by Takanari Hayama <taki@igel.co.jp>
Adds support framework necessary to use Media RAM (MERAM)
caching functionality with the LCDC. The MERAM is accessed
through up to 4 Interconnect Buffers (ICBs).
ICB numbers and MERAM address ranges to use are specified in
by filling in the .meram_cfg member of the LCDC platform data
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add the support for NV12 color format.
Configure base address for UV component of NV12 color format.
Change the way chroma scaling is handled for YUV formats on OMAP4 by enabling
chroma-resampling for video pipeline and hence using FIR2 register set for
scaling UV.
Changes to _dispc_set_scaling(), because of the reason above, are:
- call _dispc_set_scaling_common() to handle scaling for all color formats
except for OMAP4 where it only handles scaling for RGB or Y-component
- call _dispc_set_scaling_uv() for special handling required for UV
component on OMAP4.
- dispc_set_scaling_uv() also resets chroma-resampling bit for RGB color modes.
Contains chroma scaling (_dispc_set_scaling_uv) design and implemented by
Lajos Molnar <molnar@ti.com>
Signed-off-by: Amber Jain <amber@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add new color formats supported by OMAP4: NV12, RGBA16, RGBX16,
ARGB16_1555, XRGB16_1555.
NV12 color format is defined here, its support in DSS will be added separately.
Signed-off-by: Amber Jain <amber@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On OMAP3, the DSI module has 2 data lanes. On OMAP4, DSI1 has 4 data lanes
and DSI2 has 2 data lanes. Introduce function dsi_get_num_data_lanes() which
returns the number of data lanes on the dsi interface, introduce function
dsi_get_num_data_lanes_dssdev() which returns the number of data lanes used by
the omap_dss_device connected to the lanes.
Use the DSI_GNQ register on OMAP4 to get the number of data lanes, modify
dsi.c to use the number of lanes and the extra data lanes on DSI1.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add omap_rfbi_configure() which the panel driver can use to reconfigure
the data element size and the number of data lines in the RFBI bus.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add similar bus lock to RFBI as is in DSI. The panel driver can use the
bus lock to mark that the RFBI bus is currently in use.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Introduce DSI2 PLL clock sources needed by LCD2 channel and DSI2 Protocol
engine and DISPC Functional clock. Do the following:
- Modify dss_get_dsi_clk_source() and dss_select_dsi_clk_source() to take the
dsi module number as an argument.
- Create debugfs files for dsi2, split the corresponding debugfs functions.
- Allow DPI to use these new clock sources.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI interface is represented as a platform device, using the DSI platform
driver(dsi.c). The current DSI driver design is capable of running only one
instance of a DSI device. On OMAP4, there are 2 very similar DSI modules which
can be represented as instances of "omapdss_dsi" platform device.
Add member "module" in "dssdev.phy.dsi" that tells us which DSI module's lanes
the panel is connected to. Modify dsi.c functions to take the device's
platform_device struct pointer, provide functions dsi_get_dsidev_from_dssdev()
and dsi_get_dsidev_from_id() take the panel's omap_dss_device and module number
respectively, and return the platform_device pointer. Currently, the dsi struct
is declared globally and is accessed when dsi data is needed. The new pdev
argument will be used later to provide the platform device's dsi related data.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add pointer to omap_dss_device struct as an argument in the functions which
are exported to dsi panel drivers. This argument will tell the DSI driver
which DSI interface's data it has to choose.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
ULPS is a low power state where the DSI lanes are kept at ground. This
patch implements ULPS by having a DSI bus inactivity timer which
triggers the entry to ULPS. ULPS exit will happen automatically when the
driver needs to do something on the DSI lanes.
The ulps_timeout is configurable from board file or via sysfs.
Additionally another sysfs file, "ulps", can be used to check the
current ULPS state, or to manually enter or exit ULPS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
ESD check in Taal driver is currently on/off feature with hardcoded
interval. This patch changes it to a configurable interval, which can be
set from the board file.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add dsi_mux_pads function pointer to omap_dss_board_info, and use the
function pointer in DSI code to configure the DSI pads either to normal
DSI operation, or to pull down when in ULPS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add parameter to omapdss_dsi_display_disable() which the panel driver
can use to tell if the DSI lanes should be put to ULPS before disabling
the interface.
This can be used to skip ULPS entry in cases where the panel doesn't
care about ULPS state, for example when the panel will be reset, or when
the display interface will be enabled again right after the disable.
This will speed up the operation considerably in cases where entering
ULPS would fail with timeout, and the panel driver isn't even interested
in entering ULPS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI pins are powered by VDDS_DSI. If VDDS_DSI is off, the DSI pins
are floating even if they are pinmuxed to, say, safe mode and there's a
pull down/up.
This patch gives the panel drivers an option to leave the VDDS_DSI power
enabled while the DSS itself is turned off. This can be used to keep the
DSI lanes in a valid state while DSS is off, if the DSI pins are muxed
for pull down (not done in this patch).
There will be a slight power consumption increase (~100 uA?) when the
VDDS_DSI is left on, but because this option is used when the panel is
left on, the regulator consumption is negligible compared to panel power
consumption.
When the panel is fully turned off the VDDS_DSI is also turned off.
As an added bonus this will give us faster start up time when starting
up the DSS and the regulator is already enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move some of the configurable HDMI PLL parameters to dssdev.clock struct.
Cleanup the function hdmi_compute_pll() by using the parameters defined in the
board file and do some cosmetic modifications.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add enum dss_clock_source in dssdev.clocks struct so that the clock sources can
be specified in the board file.
Replace hard coded clock sources in dsi.c, dpi.c and replace them with the new
clock source members in dssdev.clocks. Modify the sdp4430_lcd_device struct in
board-4430sdp.c to specify clock sources for DISPC_FCLK, LCD1_CLK and DSI1_FCLK.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Change enum dss_clk_source to omap_dss_clock_source and move it to
'plat/display.h'. Change the enum members to attach "OMAP_" in the beginning.
These changes are done in order to specify the clock sources for DSS in the
board file.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_dss_register_device and omap_dss_unregister_device can only be
called from core.c, so we can make it static.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add get_dimensions() to struct omap_dss_driver. Use the call, if supported
by the driver, in OMAPFB.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clock configuration was defined inside dssdev.phy.dsi struct. The clock
config doesn't really belong there, and so it's moved to dssdev.clock
struct.
Now the explicit clock configuration could also be used for other
interfaces than DSI, although there's no support for it currently.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/nokia-dsi-panel.h is an include for the
OMAP DSS panel driver for Nokia's DSI displays. A more logical place for
it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/panel-generic-dpi.h is an include for
the OMAP DSS panel driver for generic DPI displays. A more logical place
for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Florian Tobias Schandinat
Laurent Pinchart
Archit Taneja
Chandrabhanu Mahapatra
Tomi Valkeinen
Linus Torvalds
Donghwa Lee
Kuninori Morimoto
Ricardo Neri
Jingoo Han
Heiko Stübner
Grazvydas Ignotas
Geert Uytterhoeven
Bernie Thompson
Russell King
Mythri P K
David Howells
Mayuresh Janorkar
Paul Mundt
Damian
Amber Jain
Jani Nikula
Jiri Kosina
Justin P. Mattock