target_complete_cmd() and friends requires a SAM status type, so passing
GOOD here is actually wrong.
Link: https://lore.kernel.org/r/20210427083046.31620-40-hare@suse.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename function local variable i to sg_cnt so we can get rid of the
shadow variable compilation warning:
unsigned int i;
^
int i;
^
Link: https://lore.kernel.org/r/20210228055645.22253-6-chaitanya.kulkarni@wdc.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SBC-4 r15 5.3 COMPARE AND WRITE command states:
if the compare operation does not indicate a match, then terminate the
command with CHECK CONDITION status with the sense key set to
MISCOMPARE and the additional sense code set to MISCOMPARE DURING
VERIFY OPERATION. In the sense data (see 4.18 and SPC-5) the offset
from the start of the Data-Out Buffer to the first byte of data that
was not equal shall be reported in the INFORMATION field.
This change implements the missing logic to report the miscompare offset in
the sense data INFORMATION field. As an optimization, byte-by-byte
miscompare offset calculation is only performed after memcmp() mismatch.
Link: https://lore.kernel.org/r/20201031233211.5207-5-ddiss@suse.de
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation for finding and returning the miscompare offset.
Link: https://lore.kernel.org/r/20201031233211.5207-4-ddiss@suse.de
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
cmd.bad_sector currently gets packed into the sense INFORMATION field for
TCM_LOGICAL_BLOCK_{GUARD,APP_TAG,REF_TAG}_CHECK_FAILED errors, which carry
an .add_sector_info flag in the sense_detail_table to ensure this.
In preparation for propagating a byte offset on COMPARE AND WRITE
TCM_MISCOMPARE_VERIFY error, rename cmd.bad_sector to cmd.sense_info and
sense_detail.add_sector_info to sense_detail.add_sense_info so that it
better reflects the sense INFORMATION field destination.
[ddiss: update previously overlooked ib_isert]
Link: https://lore.kernel.org/r/20201031233211.5207-3-ddiss@suse.de
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
COMPARE AND WRITE command execution starts with a call of
sbc_compare_and_write(). That function locks the caw_sem member in the
backend device data structure and submits a read request to the backend
driver. Upon successful completion of the read compare_and_write_callback()
gets called. That last function compares the data that has been read. If it
matches transport_complete_callback is set to compare_and_write_post and a
write request is submitted. compare_and_write_post() submits a write request
to the backend driver.
XDWRITEREAD command execution starts with sbc_execute_rw() submitting a
read to the backend device. Upon successful completion of the read the
xdreadwrite_callback() gets called. That function xors the data that has
been read with the data in the data-out buffer and stores the result in
the data-in buffer.
Call transport_complete_callback() not only if COMPARE AND WRITE fails but
also if XDWRITEREAD fails. This makes the code more systematic. Make sure
that the callback functions handle (cmd, false, NULL) argument triples fine.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The purpose of sg_alloc_table() is to allocate and initialize an
sg-list. Use that function instead of open-coding it. This patch will
make it easier to share code for caching sg-list allocations between the
SCSI and NVMe target cores.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 057085e522 ("target: Fix race for SCF_COMPARE_AND_WRITE_POST
checking") removed the code that checks the SCF_COMPARE_AND_WRITE_POST
flag. Hence also remove the flag itself.
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some target code uses config_item_name() while other code accesses .ci_name
directly. Make the target code consistent by switching to
config_item_name().
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a length of a range is zero, it means there is nothing to unmap
and we can skip this range.
Here is one more reason, why we have to skip such ranges. An unmap
callback calls file_operations->fallocate(), but the man page for the
fallocate syscall says that fallocate(fd, mode, offset, let) returns
EINVAL, if len is zero. It means that file_operations->fallocate() isn't
obligated to handle zero ranges too.
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"It's been usually busy for summer, with most of the efforts centered
around TCMU developments and various target-core + fabric driver bug
fixing activities. Not particularly large in terms of LoC, but lots of
smaller patches from many different folks.
The highlights include:
- ibmvscsis logical partition manager support (Michael Cyr + Bryant
Ly)
- Convert target/iblock WRITE_SAME to blkdev_issue_zeroout (hch +
nab)
- Add support for TMR percpu LUN reference counting (nab)
- Fix a potential deadlock between EXTENDED_COPY and iscsi shutdown
(Bart)
- Fix COMPARE_AND_WRITE caw_sem leak during se_cmd quiesce (Jiang Yi)
- Fix TMCU module removal (Xiubo Li)
- Fix iser-target OOPs during login failure (Andrea Righi + Sagi)
- Breakup target-core free_device backend driver callback (mnc)
- Perform TCMU add/delete/reconfig synchronously (mnc)
- Fix TCMU multiple UIO open/close sequences (mnc)
- Fix TCMU CHECK_CONDITION sense handling (mnc)
- Fix target-core SAM_STAT_BUSY + TASK_SET_FULL handling (mnc + nab)
- Introduce TYPE_ZBC support in PSCSI (Damien Le Moal)
- Fix possible TCMU memory leak + OOPs when recalculating cmd base
size (Xiubo Li + Bryant Ly + Damien Le Moal + mnc)
- Add login_keys_workaround attribute for non RFC initiators (Robert
LeBlanc + Arun Easi + nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (68 commits)
iscsi-target: Add login_keys_workaround attribute for non RFC initiators
Revert "qla2xxx: Fix incorrect tcm_qla2xxx_free_cmd use during TMR ABORT"
tcmu: clean up the code and with one small fix
tcmu: Fix possbile memory leak / OOPs when recalculating cmd base size
target: export lio pgr/alua support as device attr
target: Fix return sense reason in target_scsi3_emulate_pr_out
target: Fix cmd size for PR-OUT in passthrough_parse_cdb
tcmu: Fix dev_config_store
target: pscsi: Introduce TYPE_ZBC support
target: Use macro for WRITE_VERIFY_32 operation codes
target: fix SAM_STAT_BUSY/TASK_SET_FULL handling
target: remove transport_complete
pscsi: finish cmd processing from pscsi_req_done
tcmu: fix sense handling during completion
target: add helper to copy sense to se_cmd buffer
target: do not require a transport_complete for SCF_TRANSPORT_TASK_SENSE
target: make device_mutex and device_list static
tcmu: Fix flushing cmd entry dcache page
tcmu: fix multiple uio open/close sequences
tcmu: drop configured check in destroy
...
Introduce the function get_unaligned_be24(). Use {get,put}_unaligned_be*()
where appropriate. This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In struct se_dev_attrib, there is a field emulate_caw exposed
as a /sys/kernel/config/target/core/$HBA/$DEV/attrib/.
If this field is set zero, it means the corresponding struct se_device
does not support the scsi cmd COMPARE_AND_WRITE
In function sbc_parse_cdb(), go ahead and reject scsi COMPARE_AND_WRITE
if emulate_caw is not set, because it has been explicitly disabled
from user-space.
(Make pr_err ratelimited - nab)
Signed-off-by: Jiang Yi <jiangyilism@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This reverts commit 0e2eb7d12e
Author: Bart Van Assche <bart.vanassche@sandisk.com>
Date: Thu Mar 30 10:12:39 2017 -0700
target: Fix VERIFY and WRITE VERIFY command parsing
This patch broke existing behaviour for WRITE_VERIFY because
it dropped the original SCF_SCSI_DATA_CDB assignment for
bytchk = 0 so target_cmd_size_check() no longer rejected
this case, allowing an overflow case to trigger an OOPs
in iscsi-target.
Since the short term and long term fixes are still being
discussed, revert it for now since it's late in the merge
window and try again in v4.13-rc1.
Conflicts:
drivers/target/target_core_sbc.c
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Following the bugfix for handling non SAM_STAT_GOOD COMPARE_AND_WRITE
status during COMMIT phase in commit 9b2792c3da, the same bug exists
for the READ phase as well.
This would manifest first as a lost SCSI response, and eventual
hung task during fabric driver logout or re-login, as existing
shutdown logic waited for the COMPARE_AND_WRITE se_cmd->cmd_kref
to reach zero.
To address this bug, compare_and_write_callback() has been changed
to set post_ret = 1 and return TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE
as necessary to signal failure status.
Reported-by: Bill Borsari <wgb@datera.io>
Cc: Bill Borsari <wgb@datera.io>
Tested-by: Gary Guo <ghg@datera.io>
Cc: Gary Guo <ghg@datera.io>
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses clients who needs write_verify_16 for
large volume groups such as AIX.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data structure by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use the value of the BYTCHK field to determine the size of the
Data-Out buffer. For VERIFY, honor the VRPROTECT, DPO and FUA
fields. This patch avoids that LIO complains about a mismatch
between the expected transfer length and the SCSI CDB length
if the value of the BYTCHK field is 0.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Max Lohrmann <post@wickenrode.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As reported by Max, the Windows 2008 R2 chkdsk utility expects
VERIFY_16 to be supported, and does not handle the returned
CHECK_CONDITION properly, resulting in an infinite loop.
The kernel will log huge amounts of this error:
kernel: TARGET_CORE[iSCSI]: Unsupported SCSI Opcode 0x8f, sending
CHECK_CONDITION.
Signed-off-by: Max Lohrmann <post@wickenrode.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The patch that reworks task management function handling guarantees
that target_remove_from_state_list() is always called with CMD_T_BUSY
cleared. Since that function is the only function that tests that flag
this means that that flag is now superfluous. Hence remove that flag.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a long standing bug where the commit phase
of COMPARE_AND_WRITE would result in a se_cmd->cmd_kref reference
leak if se_cmd->scsi_status returned non SAM_STAT_GOOD.
This would manifest first as a lost SCSI response, and eventual
hung task during fabric driver logout or re-login, as existing
shutdown logic waited for the COMPARE_AND_WRITE se_cmd->cmd_kref
to reach zero.
To address this bug, compare_and_write_post() has been changed
to drop the incorrect !cmd->scsi_status conditional that was
preventing *post_ret = 1 for being set during non SAM_STAT_GOOD
status.
This patch has been tested with SAM_STAT_CHECK_CONDITION status
from normal target_complete_cmd() callback path, as well as the
incoming __target_execute_cmd() submission failure path when
se_cmd->execute_cmd() returns non zero status.
Reported-by: Donald White <dew@datera.io>
Cc: Donald White <dew@datera.io>
Tested-by: Gary Guo <ghg@datera.io>
Cc: Gary Guo <ghg@datera.io>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove superfluous #include directives from the include/target/*.h
files. Add missing #include directives to other *.h and *.c files.
Use forward declarations for structures where possible. This
change reduces the build time for make M=drivers/target on my
laptop from 27.1s to 18.7s or by about 30%.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
If a command with a Simple task attribute is failed due to a Unit
Attention, then a subsequent command with an Ordered task attribute
will hang forever. The reason for this is that the Unit Attention
status is checked for in target_setup_cmd_from_cdb, before the call
to target_execute_cmd, which calls target_handle_task_attr, which
in turn increments dev->simple_cmds.
However, transport_generic_request_failure still calls
transport_complete_task_attr, which will decrement dev->simple_cmds.
In this case, simple_cmds is now -1. So when a command with the
Ordered task attribute is sent, target_handle_task_attr sees that
dev->simple_cmds is not 0, so it decides it can't execute the
command until all the (nonexistent) Simple commands have completed.
Reported-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Tested-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Reported-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # 4.4+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Introduce configfs support for unlocked configfs_depend_item()
(krzysztof + andrezej)
- Conversion of usb-gadget target driver to new function registration
interface (andrzej + sebastian)
- Enable qla2xxx FC target mode support for Extended Logins (himansu +
giridhar)
- Enable qla2xxx FC target mode support for Exchange Offload (himansu +
giridhar)
- Add qla2xxx FC target mode irq affinity notification + selective
command queuing. (quinn + himanshu)
- Fix iscsi-target deadlock in se_node_acl configfs deletion (sagi +
nab)
- Convert se_node_acl configfs deletion + se_node_acl->queue_depth to
proper se_session->sess_kref + target_get_session() usage. (hch +
sagi + nab)
- Fix long-standing race between se_node_acl->acl_kref get and
get_initiator_node_acl() lookup. (hch + nab)
- Fix target/user block-size handling, and make sure netlink reaches
all network namespaces (sheng + andy)
Note there is an outstanding bug-fix series for remote I_T nexus port
TMR LUN_RESET has been posted and still being tested, and will likely
become post -rc1 material at this point"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (56 commits)
scsi: qla2xxxx: avoid type mismatch in comparison
target/user: Make sure netlink would reach all network namespaces
target: Obtain se_node_acl->acl_kref during get_initiator_node_acl
target: Convert ACL change queue_depth se_session reference usage
iscsi-target: Fix potential dead-lock during node acl delete
ib_srpt: Convert acl lookup to modern get_initiator_node_acl usage
tcm_fc: Convert acl lookup to modern get_initiator_node_acl usage
tcm_fc: Wait for command completion before freeing a session
target: Fix a memory leak in target_dev_lba_map_store()
target: Support aborting tasks with a 64-bit tag
usb/gadget: Remove set-but-not-used variables
target: Remove an unused variable
target: Fix indentation in target_core_configfs.c
target/user: Allow user to set block size before enabling device
iser-target: Fix non negative ERR_PTR isert_device_get usage
target/fcoe: Add tag support to tcm_fc
qla2xxx: Check for online flag instead of active reset when transmitting responses
qla2xxx: Set all queues to 4k
qla2xxx: Disable ZIO at start time.
qla2xxx: Move atioq to a different lock to reduce lock contention
...
This change sets the LBPRZ flag in EVPD page b2h and READ CAPACITY (16)
based on a new unmap_zeroes_data device attribute. This flag is set
automatically for iblock based on underlying block device queue's
discard_zeroes_data flag.
Signed-off-by: Jamie Pocas <jamie.pocas@emc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target_core_sbc's compare_and_write functionality suffers from taking
data at the wrong memory location when writing a CAW request to disk
when a SGL offset is non-zero.
This can happen with loopback and vhost-scsi fabric drivers when
SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC is used to map existing user-space
SGL memory into COMPARE_AND_WRITE READ/WRITE payload buffers.
Given the following sample LIO subtopology,
% targetcli ls /loopback/
o- loopback ................................. [1 Target]
o- naa.6001405ebb8df14a ....... [naa.60014059143ed2b3]
o- luns ................................... [2 LUNs]
o- lun0 ................ [iblock/ram0 (/dev/ram0)]
o- lun1 ................ [iblock/ram1 (/dev/ram1)]
% lsscsi -g
[3:0:1:0] disk LIO-ORG IBLOCK 4.0 /dev/sdc /dev/sg3
[3:0:1:1] disk LIO-ORG IBLOCK 4.0 /dev/sdd /dev/sg4
the following bug can be observed in Linux 4.3 and 4.4~rc1:
% perl -e 'print chr$_ for 0..255,reverse 0..255' >rand
% perl -e 'print "\0" x 512' >zero
% cat rand >/dev/sdd
% sg_compare_and_write -i rand -D zero --lba 0 /dev/sdd
% sg_compare_and_write -i zero -D rand --lba 0 /dev/sdd
Miscompare reported
% hexdump -Cn 512 /dev/sdd
00000000 0f 0e 0d 0c 0b 0a 09 08 07 06 05 04 03 02 01 00
00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*
00000200
Rather than writing all-zeroes as instructed with the -D file, it
corrupts the data in the sector by splicing some of the original
bytes in. The page of the first entry of cmd->t_data_sg includes the
CDB, and sg->offset is set to a position past the CDB. I presume that
sg->offset is also the right choice to use for subsequent sglist
members.
Signed-off-by: Jan Engelhardt <jengelh@netitwork.de>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a race + use after free where the first
stage of COMPARE_AND_WRITE in compare_and_write_callback()
is rescheduled after the backend sends the secondary WRITE,
resulting in second stage compare_and_write_post() callback
completing in target_complete_ok_work() before the first
can return.
Because current code depends on checking se_cmd->se_cmd_flags
after return from se_cmd->transport_complete_callback(),
this results in first stage having SCF_COMPARE_AND_WRITE_POST
set, which incorrectly falls through into second stage CAW
processing code, eventually triggering a NULL pointer
dereference due to use after free.
To address this bug, pass in a new *post_ret parameter into
se_cmd->transport_complete_callback(), and depend upon this
value instead of ->se_cmd_flags to determine when to return
or fall through into ->queue_status() code for CAW.
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
COMPARE AND WRITE requests should fail if DPO or FUA is set, but the
device is not advertising support.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
AIX servers using VIOS servers that virtualize FC cards will have a
problem booting without support for START_STOP_UNIT.
Cite sbc3r36 exactly, clean up if conditions (rob + hch)
Signed-off-by: Brian Bunker <brian@purestorage.com>
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: "Robert Elliott (Server Storage)" <Elliott@hp.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Its not a good idea to keep target specific definition of
the same t10-pi tuple.
(Fix v4.2-rc1 patch fuzz - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"It's been a busy development cycle for target-core in a number of
different areas.
The fabric API usage for se_node_acl allocation is now within
target-core code, dropping the external API callers for all fabric
drivers tree-wide.
There is a new conversion to RCU hlists for se_node_acl and
se_portal_group LUN mappings, that turns fast-past LUN lookup into a
completely lockless code-path. It also removes the original
hard-coded limitation of 256 LUNs per fabric endpoint.
The configfs attributes for backends can now be shared between core
and driver code, allowing existing drivers to use common code while
still allowing flexibility for new backend provided attributes.
The highlights include:
- Merge sbc_verify_dif_* into common code (sagi)
- Remove iscsi-target support for obsolete IFMarker/OFMarker
(Christophe Vu-Brugier)
- Add bidi support in target/user backend (ilias + vangelis + agover)
- Move se_node_acl allocation into target-core code (hch)
- Add crc_t10dif_update common helper (akinobu + mkp)
- Handle target-core odd SGL mapping for data transfer memory
(akinobu)
- Move transport ID handling into target-core (hch)
- Move task tag into struct se_cmd + support 64-bit tags (bart)
- Convert se_node_acl->device_list[] to RCU hlist (nab + hch +
paulmck)
- Convert se_portal_group->tpg_lun_list[] to RCU hlist (nab + hch +
paulmck)
- Simplify target backend driver registration (hch)
- Consolidate + simplify target backend attribute implementations
(hch + nab)
- Subsume se_port + t10_alua_tg_pt_gp_member into se_lun (hch)
- Drop lun_sep_lock for se_lun->lun_se_dev RCU usage (hch + nab)
- Drop unnecessary core_tpg_register TFO parameter (nab)
- Use 64-bit LUNs tree-wide (hannes)
- Drop left-over TARGET_MAX_LUNS_PER_TRANSPORT limit (hannes)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (76 commits)
target: Bump core version to v5.0
target: remove target_core_configfs.h
target: remove unused TARGET_CORE_CONFIG_ROOT define
target: consolidate version defines
target: implement WRITE_SAME with UNMAP bit using ->execute_unmap
target: simplify UNMAP handling
target: replace se_cmd->execute_rw with a protocol_data field
target/user: Fix inconsistent kmap_atomic/kunmap_atomic
target: Send UA when changing LUN inventory
target: Send UA upon LUN RESET tmr completion
target: Send UA on ALUA target port group change
target: Convert se_lun->lun_deve_lock to normal spinlock
target: use 'se_dev_entry' when allocating UAs
target: Remove 'ua_nacl' pointer from se_ua structure
target_core_alua: Correct UA handling when switching states
xen-scsiback: Fix compile warning for 64-bit LUN
target: Remove TARGET_MAX_LUNS_PER_TRANSPORT
target: use 64-bit LUNs
target: Drop duplicate + unused se_dev_check_wce
target: Drop unnecessary core_tpg_register TFO parameter
...
This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There are also one new driver: the Cisco snic; the advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions).
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJViKWdAAoJEDeqqVYsXL0MAr8IAMmlA6HBVjMJJFCEOY9corHj
e70MNQa7LUgf+JCdOtzGcvHXTiFFd4IHZAwXUJAnsC4IU2QWEfi1bjUTErlqBIGk
LoZlXXpEHnFpmWot3OluOzzcGcxede8rVgPiKWVVdojIngBC2+LL/i2vPCJ84ri9
WCVlk6KBvWZXuU6JuOKAb2FO9HOX7Q61wuKAMast2Qc6RNc2ksgc7VbstsITqzZ9
FVEsjmQ5lqUj+xdxBpiUOdUpc22IJ4VcpBgQ2HrThvg6vf4aq937RJ/g4vi/g0SU
Utk0a3bUw1H/WnYAfJVFx83nVEsS/954Z7/ERDg1sjlfLYwQtQnpov0XIbPIbZU=
=k9IT
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There is also one new driver: the Cisco snic. The advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (156 commits)
snic: driver for Cisco SCSI HBA
qla2xxx: Fix indentation
qla2xxx: Comment out unreachable code
fusion: remove dead MTRR code
advansys: fix compilation errors and warnings when CONFIG_PCI is not set
mptsas: fix depth param in scsi_track_queue_full
megaraid: fix irq setup process regression
lpfc: Update version to 10.7.0.0 for upstream patch set.
lpfc: Fix to drop PLOGIs from fabric node till LOGO processing completes
lpfc: Fix scsi task management error message.
lpfc: Fix cq_id masking problem.
lpfc: Fix scsi prep dma buf error.
lpfc: Add support for using block multi-queue
lpfc: Devices are not discovered during takeaway/giveback testing
lpfc: Fix vport deletion failure.
lpfc: Check for active portpeerbeacon.
lpfc: Update driver version for upstream patch set 10.6.0.1.
lpfc: Change buffer pool empty message to miscellaneous category
lpfc: Fix incorrect log message reported for empty FCF record.
lpfc: Fix rport leak.
...
Move a little more processing into the core code, and lift the previous
do_unmap callback into the sbc_ops structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of leaking this SBC read/write implementation detail just add an
opaqueue protocol specific pointer to struct se_cmd that we can assign
the sbc_ops vector to.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Only include SCSI initiator header files in target code that needs
these header files, namely the SCSI pass-through code and the tcm_loop
driver. Change SCSI_SENSE_BUFFERSIZE into TRANSPORT_SENSE_BUFFER in
target code because the former is intended for initiator code and the
latter for target code. With this patch the only initiator include
directives in target code that remain are as follows:
$ git grep -nHE 'include .scsi/(scsi.h|scsi_host.h|scsi_device.h|scsi_cmnd.h)' drivers/target drivers/infiniband/ulp/{isert,srpt} drivers/usb/gadget/legacy/tcm_*.[ch] drivers/{vhost,xen} include/{target,trace/events/target.h}
drivers/target/loopback/tcm_loop.c:29:#include <scsi/scsi.h>
drivers/target/loopback/tcm_loop.c:31:#include <scsi/scsi_host.h>
drivers/target/loopback/tcm_loop.c:32:#include <scsi/scsi_device.h>
drivers/target/loopback/tcm_loop.c:33:#include <scsi/scsi_cmnd.h>
drivers/target/target_core_pscsi.c:39:#include <scsi/scsi_device.h>
drivers/target/target_core_pscsi.c:40:#include <scsi/scsi_host.h>
drivers/xen/xen-scsiback.c:52:#include <scsi/scsi_host.h> /* SG_ALL */
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
sbc_dif_generate() and sbc_dif_verify() currently assume that each
SG element for data transfer memory doesn't straddle the block size
boundary.
However, when using SG_IO ioctl, we can choose the data transfer
memory which doesn't satisfy that alignment requirement.
In order to handle such cases correctly, this change inverts the outer
loop to iterate data transfer memory and the inner loop to iterate
protection information and enables to calculate CRC for a block which
straddles multiple SG elements.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: target-devel@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In sbc_dif_copy_prot(), the addresses passed to kunmap_atomic() are
inconsistent with the addresses which are mapped by kmap_atomic().
That could be problematic if an SG element has its length larger than
PAGE_SIZE as kunmap_atomic() will attempt to unmap different page.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: target-devel@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Drivers may override the WCE flag, in which case the DPOFUA flag in
MODE SENSE might differ from the check used to reject invalid FUA
bits in sbc_check_dpofua. Also now that we reject invalid FUA
bits early there is no need to duplicate the same buggy check
down in the fileio code.
As the DPOFUA flag controls th support for FUA bits on read and
write commands as well as DPO key off all the checks off a single
helper, and deprecate the emulate_dpo and emulate_fua_read attributs.
This fixes various failures in the libiscsi testsuite.
Personally I'd prefer to also remove the emulate_fua_write attribute
as there is no good reason to disable it, but I'll leave that for
a separate discussion.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix map/unmap consistency and get rid of a redundant
local variable psg.
Reported-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of providing DIF verify routines for read/write
that are almost identical and conditionally copy protection
information, just let the caller do the right thing.
Have a single sbc_dif_verify that handles an sgl (that
does NOT copy any data) and a protection information copy
routine used by rd_mcp and fileio backend.
In the WRITE case, call sbc_dif_verify with cmd->t_prot_sg
and then do the copy from it to local sgl (assuming the verify
succeeded of course). In the READ case, call sbc_dif_verify
with the local sgl and if it succeeds, copy it to t_prot_sg (or
not if we are stripping it).
(Fix apply breakage from commit c836777 - nab)
Tested-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Once upon a time, iscsit_get_tpg() was using an un-interruptible
lock. The signal_pending() usage was a check to allow userspace
to break out of the operation with SIGINT.
AFAICT, there's no reason why this is necessary anymore, and as
reported by Alexey can be potentially dangerous. Also, go ahead
and drop the other two problematic cases within iscsit_access_np()
and sbc_compare_and_write() as well.
Found by Linux Driver Verification project (linuxtesting.org).
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity in target land the last months.
The highlights include:
- Convert fabric drivers tree-wide to target_register_template() (hch
+ bart)
- iser-target hardening fixes + v1.0 improvements (sagi)
- Convert iscsi_thread_set usage to kthread.h + kill
iscsi_target_tq.c (sagi + nab)
- Add support for T10-PI WRITE_STRIP + READ_INSERT operation (mkp +
sagi + nab)
- DIF fixes for CONFIG_DEBUG_SG=y + UNMAP file emulation (akinobu +
sagi + mkp)
- Extended TCMU ABI v2 for future BIDI + DIF support (andy + ilias)
- Fix COMPARE_AND_WRITE handling for NO_ALLLOC drivers (hch + nab)
Thanks to everyone who contributed this round with new features,
bug-reports, fixes, cleanups and improvements.
Looking forward, it's currently shaping up to be a busy v4.2 as well"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (69 commits)
target: Put TCMU under a new config option
target: Version 2 of TCMU ABI
target: fix tcm_mod_builder.py
target/file: Fix UNMAP with DIF protection support
target/file: Fix SG table for prot_buf initialization
target/file: Fix BUG() when CONFIG_DEBUG_SG=y and DIF protection enabled
target: Make core_tmr_abort_task() skip TMFs
target/sbc: Update sbc_dif_generate pr_debug output
target/sbc: Make internal DIF emulation honor ->prot_checks
target/sbc: Return INVALID_CDB_FIELD if DIF + sess_prot_type disabled
target: Ensure sess_prot_type is saved across session restart
target/rd: Don't pass incomplete scatterlist entries to sbc_dif_verify_*
target: Remove the unused flag SCF_ACK_KREF
target: Fix two sparse warnings
target: Fix COMPARE_AND_WRITE with SG_TO_MEM_NOALLOC handling
target: simplify the target template registration API
target: simplify target_xcopy_init_pt_lun
target: remove the unused SCF_CMD_XCOPY_PASSTHROUGH flag
target/rd: reduce code duplication in rd_execute_rw()
tcm_loop: fixup tpgt string to integer conversion
...
Now that sbc_dif_generate can also be called for READ_INSERT, update
the debugging message accordingly.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The internal DIF emulation was not honoring se_cmd->prot_checks for
the WRPROTECT/RDPROTECT == 0x3 case, so sbc_dif_v1_verify() has been
updated to follow which checks have been calculated based on
WRPROTECT/RDPROTECT in sbc_set_prot_op_checks().
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In sbc_check_prot(), if PROTECT is non-zero for a backend device with
DIF disabled, and sess_prot_type is not set go ahead and return
INVALID_CDB_FIELD.
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Dmitry Bogdanov
Hannes Reinecke
Chaitanya Kulkarni
David Disseldorp
Gustavo A. R. Silva
Thomas Gleixner
Bart Van Assche
Bart Van Assche
Andrei Vagin
Linus Torvalds
Bart Van Assche
Jiang Yi
Dmitry Monakhov
Nicholas Bellinger
Bryant G. Ly
Markus Elfring
Max Lohrmann
Jamie Pocas
Jan Engelhardt
Brian Bunker
Sagi Grimberg
Christoph Hellwig
Akinobu Mita