The path through add_memory_section() when the memory block already
exists uses flawed refcounting logic. A get_device() is done on a
memory block using a pointer that might not be valid as we dropped
our previous reference and didn't obtain a new reference in the
proper way.
Lets stop pretending and just remove the get/put. The
mem_sysfs_mutex, which we hold over the entire init loop now, will
prevent the memory blocks from disappearing from under us.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that add_memory_section() is only called from boot time, reduce
the logic and remove the enum.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add_memory_section() is currently called from both boot time and run
time via hotplug and there is a lot of nastiness to allow for shared
code including an enum parameter to convey the calling context to
add_memory_section().
This patch is the first step in breaking up the messy code sharing by
pulling the hotplug path for add_memory_section() directly into
register_new_memory().
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the [get|put]_device functions for ref'ing the memory block device
rather than the kobject functions which should be hidden away by the
device layer.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error variable is not needed.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point in releasing the mutex for each section that is added
during boot time. Just hold it over the entire initialization loop.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid overlapping register regions by making the initial blklen of a new
node 1. If a register write occurs to a yet uncached register, that is
lower than but near an existing node's base_reg, a new node is created
and it's blklen is set to an arbitrary value (sizeof(*rbnode)). That may
cause this node to overlap with another node. Those nodes should be merged,
but this merge doesn't happen yet, so this patch at least makes the initial
blklen small enough to avoid hitting the wrong node, which may otherwise
lead to severe breakage.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
CPUs are also registered as devices but the of_node in these cpu
devices are not initialized. Currently different drivers requiring
to access cpu device node are parsing the nodes themselves and
initialising the of_node in cpu device.
The of_node in all the cpu devices needs to be initialized properly
and at one place. The best place to update this is CPU subsystem
driver when registering the cpu devices.
The OF/DT core library now provides of_get_cpu_node to retrieve a cpu
device node for a given logical index by abstracting the architecture
specific details.
This patch uses of_get_cpu_node to assign of_node when registering the
cpu devices.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
__init belongs after the return type on functions, not before it.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__init belongs after the return type on functions, not before it.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__init belongs after the return type on functions, not before it.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It may be useful to register multiple patches with regmap, for example
one that depends on the device revision and one that depends on the system
configuration. Add support for doing this, appending any new patches to
the existing patches.
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a potential race condition between cpu_subsys_online()
and either acpi_processor_remove() or remove_memory() that execute
try_offline_node(). Namely, it is possible that cpu_subsys_online()
will run right after the CPUs NUMA node has been put offline and
cpu_to_node() executed by it will return NUMA_NO_NODE (-1). In
that case the CPU is gone and it doesn't make sense to call cpu_up()
for it, so make cpu_subsys_online() return -ENODEV then.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute groups are much more flexible than just a list of attributes,
due to their support for visibility of the attributes, and binary
attributes. Add bus_groups to struct bus_type which should be used
instead of bus_attrs.
bus_attrs will be removed from the structure soon.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute groups are much more flexible than just a list of attributes,
due to their support for visibility of the attributes, and binary
attributes. Add drv_groups to struct bus_type which should be used
instead of drv_attrs.
drv_attrs will be removed from the structure soon.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute groups are much more flexible than just a list of attributes,
due to their support for visibility of the attributes, and binary
attributes. Add dev_groups to struct bus_type which should be used
instead of dev_attrs.
dev_attrs will be removed from the structure soon.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regmap_writeable() check should not be done in
regcache_write() because this prevents read-only
registers to be cached. After a read on a read-only
register its value will not be stored in the cache
and the next time someone will try to read it the
value will be read from the bus instead of the
cache.
Instead the regmap_writeable() check should be done
in _regmap_write() to prevent callers from writing
to read-only registers.
Signed-off-by: Ionut Nicu <ioan.nicu.ext@nsn.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the initial case when no reg_defaults values are
provided and no register value was added to the cache
yet, the cache_present bitmap is NULL. If this function
is invoked for any register it should return false
(i.e. the register is not cached) instead of true.
Signed-off-by: Ionut Nicu <ioan.nicu.ext@nsn.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
I see no reason why a virtual range shouldn't be allowed to cover its
own data window if the page selection register is in the same place
on every page.
For chips which use paged access for all of their registers, but only
when connected via I2C, and which can access the whole register space
directly when connected via SPI, this allows to avoid acrobatics with
the register ranges by simply mapping the I2C ranges over the data
window beginning at 0x0, and then using linear access for the SPI
variant.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Export opp_add() so that modules can use it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
regcache_sync_block_raw_flush() expects the address of the register after last
register that needs to be synced as its parameter. But the last call to
regcache_sync_block_raw_flush() in regcache_sync_block_raw() passes the address
of the last register in the block. This effectively always skips over the last
register in a block, even if it needs to be synced. In order to fix it increase
the address by one register.
The issue was introduced in commit 75a5f89 ("regmap: cache: Write consecutive
registers in a single block write").
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
arch_provides_topology_pointers was introduced in commit 23ca4bba3 (x86:
cleanup early per cpu variables/accesses v4) to indicate pointers to the
topology cpumask_t maps are valid to avoid copying data on to/off of the
stack.
But later in commit fbd59a8d (cpumask: Use topology_core_cpumask()/
topology_thread_cpumask()), the pointers to the topology struct cpumask maps
are always valid.
After that commit, the only difference is that there is a redundant
"unsigned int cpu = dev->id;" if arch_provides_topology_pointers defined, but
dev->id is type 'u32' which devolves to 'unsigned int' on all supported arches.
So this arch_provides_topology_pointers define is pointless and only cause
obfuscation now, remove it.
Tested on x86 machine, topology information in sys/devices/system/cpu/
cpuX/topology/ is the same after appling this patch set.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new trace event is added to PM events to print the time it takes to
suspend and resume a device. It generates trace messages that
include device, driver, parent information in addition to the type of
PM ops invoked as well as the PM event and error status from the PM
ops. Example trace below:
bash-2239 [000] .... 290.883035: device_pm_report_time: backlight
acpi_video0 parent=0000:00:02.0 state=freeze ops=class nsecs=332 err=0
bash-2239 [000] .... 290.883041: device_pm_report_time: rfkill rf
kill3 parent=phy0 state=freeze ops=legacy class nsecs=216 err=0
bash-2239 [001] .... 290.973892: device_pm_report_time: ieee80211
phy0 parent=0000:01:00.0 state=freeze ops=legacy class nsecs=90846477 err=0
bash-2239 [001] .... 293.660129: device_pm_report_time: ieee80211 phy0 parent=0000:01:00.0 state=restore ops=legacy class nsecs=101295162 err=0
bash-2239 [001] .... 293.660147: device_pm_report_time: rfkill rfkill3 parent=phy0 state=restore ops=legacy class nsecs=1804 err=0
bash-2239 [001] .... 293.660157: device_pm_report_time: backlight acpi_video0 parent=0000:00:02.0 state=restore ops=class nsecs=757 err=0
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The usage of strict_strto*() is not preferred, because
strict_strto*() is obsolete. Thus, kstrto*() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moved 11 calls to the EXPORT_SYMBOL_GPL beneath their respective functions per
checkpatch.pl warnings.
Signed-off-by: David Graham White <dgwhite11@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the hardware interrupt mask register does not prevent the chip level
irq from being asserted by the corresponding interrupt status bit, already
set interrupt bits should to be cleared once after masking them during
initialization. Add a flag to let drivers enable this behavior.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Here are some driver core patches for 3.11-rc2. They aren't really
bugfixes, but a bunch of new helper macros for drivers to properly
create attribute groups, which drivers and subsystems need to fix up a
ton of race issues with incorrectly creating sysfs files (binary and
normal) after userspace has been told that the device is present.
Also here is the ability to create binary files as attribute groups, to
solve that race condition, which was impossible to do before this, so
that's my fault the drivers were broken.
The majority of the .c changes is indenting and moving code around a
bit. It affects no existing code, but allows the large backlog of 70+
patches that I already have created to start flowing into the different
subtrees, instead of having to live in my driver-core tree, causing
merge nightmares in linux-next for the next few months.
These were finalized too late for the -rc1 merge window, which is why
they were didn't make that pull request, testing and review from others
didn't happen until a few weeks ago, and then there's the whole
distraction of the past few days, which prevented these from getting to
you sooner, sorry about that.
Oh, and there's a bugfix for the documentation build warning in here as
well. All of these have been in linux-next this week, with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iEYEABECAAYFAlHoRUUACgkQMUfUDdst+ymkNACdHAjEXZZmXohDuCb2SqyMeQsz
AZcAn3qqJa/NoPEgTCgOkDlAQZM6BnC5
=+Gqk
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here are some driver core patches for 3.11-rc2. They aren't really
bugfixes, but a bunch of new helper macros for drivers to properly
create attribute groups, which drivers and subsystems need to fix up a
ton of race issues with incorrectly creating sysfs files (binary and
normal) after userspace has been told that the device is present.
Also here is the ability to create binary files as attribute groups,
to solve that race condition, which was impossible to do before this,
so that's my fault the drivers were broken.
The majority of the .c changes is indenting and moving code around a
bit. It affects no existing code, but allows the large backlog of 70+
patches that I already have created to start flowing into the
different subtrees, instead of having to live in my driver-core tree,
causing merge nightmares in linux-next for the next few months.
These were finalized too late for the -rc1 merge window, which is why
they were didn't make that pull request, testing and review from
others didn't happen until a few weeks ago, and then there's the whole
distraction of the past few days, which prevented these from getting
to you sooner, sorry about that.
Oh, and there's a bugfix for the documentation build warning in here
as well. All of these have been in linux-next this week, with no
reported problems"
* tag 'driver-core-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver-core: fix new kernel-doc warning in base/platform.c
sysfs: use file mode defines from stat.h
sysfs: add more helper macro's for (bin_)attribute(_groups)
driver core: add default groups to struct class
driver core: Introduce device_create_groups
sysfs: prevent warning when only using binary attributes
sysfs: add support for binary attributes in groups
driver core: device.h: add RW and RO attribute macros
sysfs.h: add BIN_ATTR macro
sysfs.h: add ATTRIBUTE_GROUPS() macro
sysfs.h: add __ATTR_RW() macro
Pull phase two of __cpuinit removal from Paul Gortmaker:
"With the __cpuinit infrastructure removed earlier, this group of
commits only removes the function/data tagging that was done with the
various (now no-op) __cpuinit related prefixes.
Now that the dust has settled with yesterday's v3.11-rc1, there
hopefully shouldn't be any new users leaking back in tree, but I think
we can leave the harmless no-op stubs there for a release as a
courtesy to those who still have out of tree stuff and weren't paying
attention.
Although the commits are against the recent tag to allow for minor
context refreshes for things like yesterday's v3.11-rc1~ slab content,
the patches have been largely unchanged for weeks, aside from such
trivial updates.
For detail junkies, the largely boring and mostly irrelevant history
of the patches can be viewed at:
http://git.kernel.org/cgit/linux/kernel/git/paulg/cpuinit-delete.git
If nothing else, I guess it does at least demonstrate the level of
involvement required to shepherd such a treewide change to completion.
This is the same repository of patches that has been applied to the
end of the daily linux-next branches for the past several weeks"
* 'cpuinit_phase2' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (28 commits)
block: delete __cpuinit usage from all block files
drivers: delete __cpuinit usage from all remaining drivers files
kernel: delete __cpuinit usage from all core kernel files
rcu: delete __cpuinit usage from all rcu files
net: delete __cpuinit usage from all net files
acpi: delete __cpuinit usage from all acpi files
hwmon: delete __cpuinit usage from all hwmon files
cpufreq: delete __cpuinit usage from all cpufreq files
clocksource+irqchip: delete __cpuinit usage from all related files
x86: delete __cpuinit usage from all x86 files
score: delete __cpuinit usage from all score files
xtensa: delete __cpuinit usage from all xtensa files
openrisc: delete __cpuinit usage from all openrisc files
m32r: delete __cpuinit usage from all m32r files
hexagon: delete __cpuinit usage from all hexagon files
frv: delete __cpuinit usage from all frv files
cris: delete __cpuinit usage from all cris files
metag: delete __cpuinit usage from all metag files
tile: delete __cpuinit usage from all tile files
sh: delete __cpuinit usage from all sh files
...
Fix new kernel-doc warning in drivers/base/platform.c:
Warning(drivers/base/platform.c:528): No description found for parameter 'owner'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should be using groups, not attribute lists, for classes to allow
subdirectories, and soon, binary files. Groups are just more flexible
overall, so add them.
The dev_attrs list will go away after all in-kernel users are converted
to use dev_groups.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_create_groups lets callers create devices as well as associated
sysfs attributes with a single call. This avoids race conditions seen
if sysfs attributes on new devices are created later.
[fixed up comment block placement and add checks for printk buffer
formats - gregkh]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following sparse warnings:
drivers/base/regmap/regmap.c:305:13: warning: context imbalance in 'regmap_lock_spinlock' - wrong count at exit
drivers/base/regmap/regmap.c:314:13: warning: context imbalance in 'regmap_unlock_spinlock' - unexpected unlock
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
PTR_RET is now deprecated. Use PTR_ERR_OR_ZERO instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This fixes a crash if something tries to do an asynchronous operation on
busless maps which was introduced during the merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c5Gp
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"Fix regmap crash for async operation on busless maps
This fixes a crash if something tries to do an asynchronous operation
on busless maps which was introduced during the merge window"
* tag 'regmap-v3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: cache: bail in regmap_async_complete() for bus-less maps
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
This removes all the remaining one-off uses of the __cpuinit macros
from all C files in the drivers/* directory.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Pull media updates from Mauro Carvalho Chehab:
"This series contain:
- new i2c video drivers: ml86v7667 (video decoder),
ths8200 (video encoder)
- a new video driver for EasyCap cards based on Fushicai USBTV007
- Improved support for OF and embedded systems, with V4L2 async
initialization and a better support for clocks
- API cleanups on the ioctls used by the v4l2 debug tool
- Lots of cleanups
- As usual, several driver improvements and new cards additions
- Revert two changesets that change the minimal symbol rate for
stv0399, as request by Manu
- Update MAINTAINERS and other files to point to my new e-mail"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (378 commits)
MAINTAINERS & ABI: Update to point to my new email
[media] stb0899: restore minimal rate to 5Mbauds
[media] exynos4-is: Correct colorspace handling at FIMC-LITE
[media] exynos4-is: Set valid initial format on FIMC.n subdevs
[media] exynos4-is: Set valid initial format on FIMC-IS-ISP subdev pads
[media] exynos4-is: Fix format propagation on FIMC-IS-ISP subdev
[media] exynos4-is: Set valid initial format at FIMC-LITE
[media] exynos4-is: Fix format propagation on FIMC-LITE.n subdevs
[media] MAINTAINERS: Update S5P/Exynos FIMC driver entry
[media] Documentation: Update driver's directory in video4linux/fimc.txt
[media] exynos4-is: Change fimc-is firmware file names
[media] exynos4-is: Add support for Exynos5250 MIPI-CSIS
[media] exynos4-is: Add Exynos5250 SoC support to fimc-lite driver
[media] exynos4-is: Drop drvdata handling in fimc-lite for non-dt platforms
[media] media: i2c: tvp514x: remove manual setting of subdev name
[media] media: i2c: tvp7002: remove manual setting of subdev name
[media] mem2mem: set missing v4l2_dev pointer
[media] wl128x: add missing struct v4l2_device
[media] tvp514x: Fix init seqeunce
[media] saa7134: Fix sparse warnings by adding __user annotation
...
Pull drm updates from Dave Airlie:
"Okay this is the big one, I was stalled on the fbdev pull req as I
stupidly let fbdev guys merge a patch I required to fix a warning with
some patches I had, they ended up merging the patch from the wrong
place, but the warning should be fixed. In future I'll just take the
patch myself!
Outside drm:
There are some snd changes for the HDMI audio interactions on haswell,
they've been acked for inclusion via my tree. This relies on the
wound/wait tree from Ingo which is already merged.
Major changes:
AMD finally released the dynamic power management code for all their
GPUs from r600->present day, this is great, off by default for now but
also a huge amount of code, in fact it is most of this pull request.
Since it landed there has been a lot of community testing and Alex has
sent a lot of fixes for any bugs found so far. I suspect radeon might
now be the biggest kernel driver ever :-P p.s. radeon.dpm=1 to enable
dynamic powermanagement for anyone.
New drivers:
Renesas r-car display unit.
Other highlights:
- core: GEM CMA prime support, use new w/w mutexs for TTM
reservations, cursor hotspot, doc updates
- dvo chips: chrontel 7010B support
- i915: Haswell (fbc, ips, vecs, watermarks, audio powerwell),
Valleyview (enabled by default, rc6), lots of pll reworking, 30bpp
support (this time for sure)
- nouveau: async buffer object deletion, context/register init
updates, kernel vp2 engine support, GF117 support, GK110 accel
support (with external nvidia ucode), context cleanups.
- exynos: memory leak fixes, Add S3C64XX SoC series support, device
tree updates, common clock framework support,
- qxl: cursor hotspot support, multi-monitor support, suspend/resume
support
- mgag200: hw cursor support, g200 mode limiting
- shmobile: prime support
- tegra: fixes mostly
I've been banging on this quite a lot due to the size of it, and it
seems to okay on everything I've tested it on."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (811 commits)
drm/radeon/dpm: implement vblank_too_short callback for si
drm/radeon/dpm: implement vblank_too_short callback for cayman
drm/radeon/dpm: implement vblank_too_short callback for btc
drm/radeon/dpm: implement vblank_too_short callback for evergreen
drm/radeon/dpm: implement vblank_too_short callback for 7xx
drm/radeon/dpm: add checks against vblank time
drm/radeon/dpm: add helper to calculate vblank time
drm/radeon: remove stray line in old pm code
drm/radeon/dpm: fix display_gap programming on rv7xx
drm/nvc0/gr: fix gpc firmware regression
drm/nouveau: fix minor thinko causing bo moves to not be async on kepler
drm/radeon/dpm: implement force performance level for TN
drm/radeon/dpm: implement force performance level for ON/LN
drm/radeon/dpm: implement force performance level for SI
drm/radeon/dpm: implement force performance level for cayman
drm/radeon/dpm: implement force performance levels for 7xx/eg/btc
drm/radeon/dpm: add infrastructure to force performance levels
drm/radeon: fix surface setup on r1xx
drm/radeon: add support for 3d perf states on older asics
drm/radeon: set default clocks for SI when DPM is disabled
...
This branch contains the following changes:
- Removal of CONFIG_OF_DEVICE, it is always enabled by CONFIG_OF
- Remove #ifdef from linux/of_platform.h to increase compiler syntax
coverage
- Bug fix for address decoding on Bimini and js2x powerpc platforms.
- miscellaneous binding changes
One note on the above. The binding changes going in from all kinds of
different trees has gotten rather out of hand. I picked up some during
this cycle, but even going though my tree isn't a great fit. Ian
Campbell has prototyped splitting the bindings and .dtb files into a
separate repository. The plan is to migrate to using that sometime in
the next few kernel releases which should get rid of a lot of the churn
on binding docs and .dts files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJR1fP3AAoJEEFnBt12D9kB3IIP/0Q5ctMespiJ50+ThjGsaR3m
sUbQkMK46uL/oupXaJT2ybX2PxLN5LpgvO9rPt77hblOoL0+wZt+j9G0pLy1qZQZ
aHprH9SrpGJv6F0SFbHp/+D/m9vESPv+zwYzL9TvrOALvCD7OSZ7tHLaoF7Y1ADM
QnZa7pta3Owpu5NsGXaTXLpaZzfXzfWzf4PDzv2FsAIDbtuVJZGJZ7sJVO7Z0r+K
KCY85uKJ4VOHY0onBVlM6uoCnopOi2XMMkyxYvR28lL2Kiv2b3np46jG3zX1EZH5
Qxdu85QZn2oio9iaTeYKK8bG9aRIRsXnzCnF2s68n2rQlEtPpWKN9Lj2AS/KJ+Ig
obFTOFDHmxt1F4GIA0/HIPkDvRd7GTIwgwYYubEMi44E3Mae0N+xzkIRE41vYP7s
8zaNHbjAjsYjplsvN5gTPxxiU/ta24a5bl7Ont2zmOjAbXCsDajm4NCKZRJ3lb2f
FHNsS1zHGmqgJ9zt13GQabo/Tp4t3KwTzBirPQsDokRO4eoL6klcS3GCRv82VWC0
dLnzu92hXcyXgh7mX2sj6sRBSwNygxMn4ZsZJklle38/LynvtrzT72BOZjghS+Vh
l553uDInjSJ3IBrXnClPoyObcu50cmsBBgsK39FzU+MF9mcCHmkHQiT52zM6ZW3M
wwY1OfcZk3XaT7akcVu6
=CndB
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree updates from Grant Likely:
"This branch contains the following changes:
- Removal of CONFIG_OF_DEVICE, it is always enabled by CONFIG_OF
- Remove #ifdef from linux/of_platform.h to increase compiler syntax
coverage
- Bug fix for address decoding on Bimini and js2x powerpc platforms.
- miscellaneous binding changes
One note on the above. The binding changes going in from all kinds of
different trees has gotten rather out of hand. I picked up some
during this cycle, but even going though my tree isn't a great fit.
Ian Campbell has prototyped splitting the bindings and .dtb files into
a separate repository. The plan is to migrate to using that sometime
in the next few kernel releases which should get rid of a lot of the
churn on binding docs and .dts files"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of: Fix address decoding on Bimini and js2x machines
of: remove CONFIG_OF_DEVICE
usb: chipidea: depend on CONFIG_OF instead of CONFIG_OF_DEVICE
of: remove of_platform_driver
ibmebus: convert of_platform_driver to platform_driver
driver core: move to_platform_driver to platform_device.h
mfd: DT bindings for the palmas family MFD
ARM: dts: omap3-devkit8000: fix NAND memory binding
of/base: fix typos
of: remove #ifdef from linux/of_platform.h
Commit f8bd822cb ("regmap: cache: Factor out block sync") made
regcache_rbtree_sync() call regmap_async_complete(), which in turn does
not check for map->bus before dereferencing it.
This causes a NULL pointer dereference on bus-less maps.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: stable@vger.kernel.org [v3.10 only]
Signed-off-by: Mark Brown <broonie@linaro.org>
Merge first patch-bomb from Andrew Morton:
- various misc bits
- I'm been patchmonkeying ocfs2 for a while, as Joel and Mark have been
distracted. There has been quite a bit of activity.
- About half the MM queue
- Some backlight bits
- Various lib/ updates
- checkpatch updates
- zillions more little rtc patches
- ptrace
- signals
- exec
- procfs
- rapidio
- nbd
- aoe
- pps
- memstick
- tools/testing/selftests updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (445 commits)
tools/testing/selftests: don't assume the x bit is set on scripts
selftests: add .gitignore for kcmp
selftests: fix clean target in kcmp Makefile
selftests: add .gitignore for vm
selftests: add hugetlbfstest
self-test: fix make clean
selftests: exit 1 on failure
kernel/resource.c: remove the unneeded assignment in function __find_resource
aio: fix wrong comment in aio_complete()
drivers/w1/slaves/w1_ds2408.c: add magic sequence to disable P0 test mode
drivers/memstick/host/r592.c: convert to module_pci_driver
drivers/memstick/host/jmb38x_ms: convert to module_pci_driver
pps-gpio: add device-tree binding and support
drivers/pps/clients/pps-gpio.c: convert to module_platform_driver
drivers/pps/clients/pps-gpio.c: convert to devm_* helpers
drivers/parport/share.c: use kzalloc
Documentation/accounting/getdelays.c: avoid strncpy in accounting tool
aoe: update internal version number to v83
aoe: update copyright date
aoe: perform I/O completions in parallel
...
Calling dev_set_name with a single paramter causes it to be handled as a
format string. Many callers are passing potentially dynamic string
content, so use "%s" in those cases to avoid any potential accidents,
including wrappers like device_create*() and bdi_register().
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Hotplug changes allowing device hot-removal operations to fail
gracefully (instead of crashing the kernel) if they cannot be
carried out completely. From Rafael J Wysocki and Toshi Kani.
- Freezer update from Colin Cross and Mandeep Singh Baines targeted
at making the freezing of tasks a bit less heavy weight operation.
- cpufreq resume fix from Srivatsa S Bhat for a regression introduced
during the 3.10 cycle causing some cpufreq sysfs attributes to
return wrong values to user space after resume.
- New freqdomain_cpus sysfs attribute for the acpi-cpufreq driver to
provide information previously available via related_cpus from
Lan Tianyu.
- cpufreq fixes and cleanups from Viresh Kumar, Jacob Shin,
Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia, Arnd Bergmann, and
Tang Yuantian.
- Fix for an ACPICA regression causing suspend/resume issues to
appear on some systems introduced during the 3.4 development cycle
from Lv Zheng.
- ACPICA fixes and cleanups from Bob Moore, Tomasz Nowicki, Lv Zheng,
Chao Guan, and Zhang Rui.
- New cupidle driver for Xilinx Zynq processors from Michal Simek.
- cpuidle fixes and cleanups from Daniel Lezcano.
- Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk.
- ACPI device power management fixes and cleanups from Fengguang Wu
and Rafael J Wysocki.
- ACPI documentation updates from Lv Zheng, Aaron Lu and Hanjun Guo.
- Fix for the IA-64 issue that was the reason for reverting commit
9f29ab1 and updates of the ACPI scan code from Rafael J Wysocki.
- Mechanism for adding CMOS RTC address space handlers from Lan Tianyu
(to allow some EC-related breakage to be fixed on some systems).
- Spec-compliant implementation of acpi_os_get_timer() from
Mika Westerberg.
- Modification of do_acpi_find_child() to execute _STA in order to
to avoid situations in which a pointer to a disabled device object
is returned instead of an enabled one with the same _ADR value.
From Jeff Wu.
- Intel BayTrail PCH (Platform Controller Hub) support for the ACPI
Intel Low-Power Subsystems (LPSS) driver and modificaions of that
driver to work around a couple of known BIOS issues from
Mika Westerberg and Heikki Krogerus.
- EC driver fix from Vasiliy Kulikov to make it use get_user() and
put_user() instead of dereferencing user space pointers blindly.
- Assorted ACPI code cleanups from Bjorn Helgaas, Nicholas Mazzuca and
Toshi Kani.
- Modification of the "runtime idle" helper routine to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows some code bloat
reduction to be done, from Rafael J Wysocki and Alan Stern.
- New trace points for PM QoS from Sahara <keun-o.park@windriver.com>.
- PM QoS documentation update from Lan Tianyu.
- Assorted core PM code cleanups and changes from Bernie Thompson,
Bjorn Helgaas, Julius Werner, and Shuah Khan.
- New devfreq driver for the Exynos5-bus device from Abhilash Kesavan.
- Minor devfreq cleanups, fixes and MAINTAINERS update from
MyungJoo Ham, Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and
Wei Yongjun.
- OMAP Adaptive Voltage Scaling (AVS) SmartReflex voltage control
driver updates from Andrii Tseglytskyi and Nishanth Menon.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=VBBq
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"This time the total number of ACPI commits is slightly greater than
the number of cpufreq commits, but Viresh Kumar (who works on cpufreq)
remains the most active patch submitter.
To me, the most significant change is the addition of offline/online
device operations to the driver core (with the Greg's blessing) and
the related modifications of the ACPI core hotplug code. Next are the
freezer updates from Colin Cross that should make the freezing of
tasks a bit less heavy weight.
We also have a couple of regression fixes, a number of fixes for
issues that have not been identified as regressions, two new drivers
and a bunch of cleanups all over.
Highlights:
- Hotplug changes to support graceful hot-removal failures.
It sometimes is necessary to fail device hot-removal operations
gracefully if they cannot be carried out completely. For example,
if memory from a memory module being hot-removed has been allocated
for the kernel's own use and cannot be moved elsewhere, it's
desirable to fail the hot-removal operation in a graceful way
rather than to crash the kernel, but currenty a success or a kernel
crash are the only possible outcomes of an attempted memory
hot-removal. Needless to say, that is not a very attractive
alternative and it had to be addressed.
However, in order to make it work for memory, I first had to make
it work for CPUs and for this purpose I needed to modify the ACPI
processor driver. It's been split into two parts, a resident one
handling the low-level initialization/cleanup and a modular one
playing the actual driver's role (but it binds to the CPU system
device objects rather than to the ACPI device objects representing
processors). That's been sort of like a live brain surgery on a
patient who's riding a bike.
So this is a little scary, but since we found and fixed a couple of
regressions it caused to happen during the early linux-next testing
(a month ago), nobody has complained.
As a bonus we remove some duplicated ACPI hotplug code, because the
ACPI-based CPU hotplug is now going to use the common ACPI hotplug
code.
- Lighter weight freezing of tasks.
These changes from Colin Cross and Mandeep Singh Baines are
targeted at making the freezing of tasks a bit less heavy weight
operation. They reduce the number of tasks woken up every time
during the freezing, by using the observation that the freezer
simply doesn't need to wake up some of them and wait for them all
to call refrigerator(). The time needed for the freezer to decide
to report a failure is reduced too.
Also reintroduced is the check causing a lockdep warining to
trigger when try_to_freeze() is called with locks held (which is
generally unsafe and shouldn't happen).
- cpufreq updates
First off, a commit from Srivatsa S Bhat fixes a resume regression
introduced during the 3.10 cycle causing some cpufreq sysfs
attributes to return wrong values to user space after resume. The
fix is kind of fresh, but also it's pretty obvious once Srivatsa
has identified the root cause.
Second, we have a new freqdomain_cpus sysfs attribute for the
acpi-cpufreq driver to provide information previously available via
related_cpus. From Lan Tianyu.
Finally, we fix a number of issues, mostly related to the
CPUFREQ_POSTCHANGE notifier and cpufreq Kconfig options and clean
up some code. The majority of changes from Viresh Kumar with bits
from Jacob Shin, Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia,
Arnd Bergmann, and Tang Yuantian.
- ACPICA update
A usual bunch of updates from the ACPICA upstream.
During the 3.4 cycle we introduced support for ACPI 5 extended
sleep registers, but they are only supposed to be used if the
HW-reduced mode bit is set in the FADT flags and the code attempted
to use them without checking that bit. That caused suspend/resume
regressions to happen on some systems. Fix from Lv Zheng causes
those registers to be used only if the HW-reduced mode bit is set.
Apart from this some other ACPICA bugs are fixed and code cleanups
are made by Bob Moore, Tomasz Nowicki, Lv Zheng, Chao Guan, and
Zhang Rui.
- cpuidle updates
New driver for Xilinx Zynq processors is added by Michal Simek.
Multidriver support simplification, addition of some missing
kerneldoc comments and Kconfig-related fixes come from Daniel
Lezcano.
- ACPI power management updates
Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk, sparse warning fix from Fengguang Wu and
cleanups and fixes of the ACPI device power state selection
routine.
- ACPI documentation updates
Some previously missing pieces of ACPI documentation are added by
Lv Zheng and Aaron Lu (hopefully, that will help people to
uderstand how the ACPI subsystem works) and one outdated doc is
updated by Hanjun Guo.
- Assorted ACPI updates
We finally nailed down the IA-64 issue that was the reason for
reverting commit 9f29ab11dd ("ACPI / scan: do not match drivers
against objects having scan handlers"), so we can fix it and move
the ACPI scan handler check added to the ACPI video driver back to
the core.
A mechanism for adding CMOS RTC address space handlers is
introduced by Lan Tianyu to allow some EC-related breakage to be
fixed on some systems.
A spec-compliant implementation of acpi_os_get_timer() is added by
Mika Westerberg.
The evaluation of _STA is added to do_acpi_find_child() to avoid
situations in which a pointer to a disabled device object is
returned instead of an enabled one with the same _ADR value. From
Jeff Wu.
Intel BayTrail PCH (Platform Controller Hub) support is added to
the ACPI driver for Intel Low-Power Subsystems (LPSS) and that
driver is modified to work around a couple of known BIOS issues.
Changes from Mika Westerberg and Heikki Krogerus.
The EC driver is fixed by Vasiliy Kulikov to use get_user() and
put_user() instead of dereferencing user space pointers blindly.
Code cleanups are made by Bjorn Helgaas, Nicholas Mazzuca and Toshi
Kani.
- Assorted power management updates
The "runtime idle" helper routine is changed to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows us to reduce the
overall code bloat a bit (by dropping some code that's not
necessary any more after that modification).
The runtime PM documentation is updated by Alan Stern (to reflect
the "runtime idle" behavior change).
New trace points for PM QoS are added by Sahara
(<keun-o.park@windriver.com>).
PM QoS documentation is updated by Lan Tianyu.
Code cleanups are made and minor issues are addressed by Bernie
Thompson, Bjorn Helgaas, Julius Werner, and Shuah Khan.
- devfreq updates
New driver for the Exynos5-bus device from Abhilash Kesavan.
Minor cleanups, fixes and MAINTAINERS update from MyungJoo Ham,
Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and Wei Yongjun.
- OMAP power management updates
Adaptive Voltage Scaling (AVS) SmartReflex voltage control driver
updates from Andrii Tseglytskyi and Nishanth Menon."
* tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
cpufreq: Fix cpufreq regression after suspend/resume
ACPI / PM: Fix possible NULL pointer deref in acpi_pm_device_sleep_state()
PM / Sleep: Warn about system time after resume with pm_trace
cpufreq: don't leave stale policy pointer in cdbs->cur_policy
acpi-cpufreq: Add new sysfs attribute freqdomain_cpus
cpufreq: make sure frequency transitions are serialized
ACPI: implement acpi_os_get_timer() according the spec
ACPI / EC: Add HP Folio 13 to ec_dmi_table in order to skip DSDT scan
ACPI: Add CMOS RTC Operation Region handler support
ACPI / processor: Drop unused variable from processor_perflib.c
cpufreq: tegra: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: s3c64xx: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: omap: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: imx6q: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: exynos: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: dbx500: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: davinci: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: arm-big-little: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: powernow-k8: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: pcc: call CPUFREQ_POSTCHANGE notfier in error cases
...
- A large slew of improvements of the Genric pin configuration
support, and deployment in four different platforms:
Rockchip, Super-H PFC, ABx500 and TZ1090. Support BIAS_BUS_HOLD,
get device tree parsing and debugfs support into shape.
- We also have device tree support with generic naming conventions
for the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now
handled in the device core: "sleep" and "idle", removing a lot
of boilerplate code in drivers. We do not yet know if this is
the final word for pin PM, but it already make things a lot
easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where
several pins are managed by a single register, and augment it to
handle sleep modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=EbAf
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
- A large slew of improvements of the Genric pin configuration support,
and deployment in four different platforms: Rockchip, Super-H PFC,
ABx500 and TZ1090. Support BIAS_BUS_HOLD, get device tree parsing
and debugfs support into shape.
- We also have device tree support with generic naming conventions for
the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now handled in
the device core: "sleep" and "idle", removing a lot of boilerplate
code in drivers. We do not yet know if this is the final word for
pin PM, but it already make things a lot easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where several
pins are managed by a single register, and augment it to handle sleep
modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
* tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: vt8500: wmt: remove redundant dev_err call in wmt_pinctrl_probe()
pinctrl: remove bindings for pinconf options needing more thought
pinctrl: remove slew-rate parameter from tz1090
pinctrl: set unit for debounce time pinconfig to usec
pinctrl: more clarifications for generic pull configs
pinctrl: rip out the direct pinconf API
pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver
pinctrl-tz1090: add TZ1090 pinctrl driver
pinctrl: samsung: Staticize drvdata_list
pinctrl: rockchip: Add missing irq_gc_unlock() call before return error
pinctrl: abx500: rework error path
pinctrl: abx500: suppress hardcoded value
pinctrl: abx500: factorize code
pinctrl: abx500: fix abx500_gpio_get()
pinctrl: abx500: fix abx500_pin_config_set()
pinctrl: abx500: Add device tree support
sh-pfc: Guard DT parsing with #ifdef CONFIG_OF
pinctrl: add Intel BayTrail GPIO/pinctrl support
pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldoc
pinctrl: Staticize local symbols
...
Conflicts:
drivers/net/ethernet/ti/davinci_mdio.c
drivers/pinctrl/Makefile
A small but useful set of regmap updates this time around:
- An abstraction for bitfields within a register map contributed by
Srinivas Kandagatla, allowing drivers to cope more easily when
hardware designers randomly move things about (mainly when talking
to things like system controllers).
- Changes from Lars-Peter Clausen to allow the MMIO regmap to be used from
hard IRQ context.
- Small improvements to the cache infrastructure and performance,
including a default cache sync operation so now all regmaps can sync
easily.
There's also a pinctrl driver making use of the new bitfield API, merged
here for dependency reasons. There will be a simple add/add conflict
with the pinctrl tree as a result.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8WLH
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"A small but useful set of regmap updates this time around:
- An abstraction for bitfields within a register map contributed by
Srinivas Kandagatla, allowing drivers to cope more easily when
hardware designers randomly move things about (mainly when talking
to things like system controllers).
- Changes from Lars-Peter Clausen to allow the MMIO regmap to be used
from hard IRQ context.
- Small improvements to the cache infrastructure and performance,
including a default cache sync operation so now all regmaps can
sync easily.
There's also a pinctrl driver making use of the new bitfield API,
merged here for dependency reasons. There will be a simple add/add
conflict with the pinctrl tree as a result."
* tag 'regmap-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
pinctrl: st: Remove unnecessary use of of_match_ptr macro
pinctrl: st: fix return value check
pinctrl: st: Add pinctrl and pinconf support.
regmap: debugfs: Suppress cache for partial register files
regmap: Add regmap_field APIs
regmap: core: Cache all registers by default when cache is enabled
regmap: Implemented default cache sync operation
regmap: Make regmap-mmio usable from atomic contexts
regmap: regcache: Fixup locking for custom lock callbacks
regmap: debugfs: Fix return from regmap_debugfs_get_dump_start
regmap: debugfs: Don't mark lockdep as broken due to debugfs write
regmap: rbtree: Use range information to allocate nodes
regmap: rbtree: Factor out node allocation
regmap: Make regmap_check_range_table() a public API
regmap: Add support for discarding parts of the register cache
We want to use CMA for allocating hash page table and real mode area for
PPC64. Hence move DMA contiguous related changes into a seperate config
so that ppc64 can enable CMA without requiring DMA contiguous.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[removed defconfig changes]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This adds support for a generic reservations framework that can be
hooked up to ttm and dma-buf and allows easy sharing of reservations
across devices.
The idea is that a dma-buf and ttm object both will get a pointer
to a struct reservation_object, which has to be reserved before
anything is done with the contents of the dma-buf.
Changes since v1:
- Fix locking issue in ticket_reserve, which could cause mutex_unlock
to be called too many times.
Changes since v2:
- All fence related calls and members have been taken out for now,
what's left is the bare minimum to be useful for ttm locking conversion.
Changes since v3:
- Removed helper functions too. The documentation has an example
implementation for locking. With the move to ww_mutex there is no
need to have much logic any more.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes another compiling warning with PM_SLEEP unset:
drivers/base/firmware_class.c:221:29: warning: 'fw_lookup_buf' defined
but not used [-Wunused-function]
This time I do build kernel with both PM_SLEEP set and unset, and no
warning found any more with the patch.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds tracepoints to dev_pm_qos_add_request, dev_pm_qos_update_request,
and dev_pm_qos_remove_request. It's useful for checking device name,
dev_pm_qos_request_type, and value.
Signed-off-by: Sahara <keun-o.park@windriver.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fixes the below compile warning:
drivers/base/firmware_class.c:1254:12: warning: 'cache_firmware' defined
but not used [-Wunused-function]
static int cache_firmware(const char *fw_name)
^
drivers/base/firmware_class.c:1281:12: warning: 'uncache_firmware'
defined but not used [-Wunused-function]
static int uncache_firmware(const char *fw_name)
^
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a938da06 introduced a useful little log message to tell
users/debuggers which wakeup source aborted a suspend. However,
this message is only printed if the abort happens during the
in-kernel suspend path (after writing /sys/power/state).
The full specification of the /sys/power/wakeup_count facility
allows user-space power managers to double-check if wakeups have
already happened before it actually tries to suspend (e.g. while it
was running user-space pre-suspend hooks), by writing the last known
wakeup_count value to /sys/power/wakeup_count. This patch changes
the sysfs handler for that node to also print said log message if
that write fails, so that we can figure out the offending wakeup
source for both kinds of suspend aborts.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* linus: (1465 commits)
ARM: tegra30: clocks: Fix pciex clock registration
lseek(fd, n, SEEK_END) does *not* go to eof - n
Linux 3.10-rc6
smp.h: Use local_irq_{save,restore}() in !SMP version of on_each_cpu().
powerpc: Fix missing/delayed calls to irq_work
powerpc: Fix emulation of illegal instructions on PowerNV platform
powerpc: Fix stack overflow crash in resume_kernel when ftracing
snd_pcm_link(): fix a leak...
use can_lookup() instead of direct checks of ->i_op->lookup
move exit_task_namespaces() outside of exit_notify()
fput: task_work_add() can fail if the caller has passed exit_task_work()
xfs: don't shutdown log recovery on validation errors
xfs: ensure btree root split sets blkno correctly
xfs: fix implicit padding in directory and attr CRC formats
xfs: don't emit v5 superblock warnings on write
mei: me: clear interrupts on the resume path
mei: nfc: fix nfc device freeing
mei: init: Flush scheduled work before resetting the device
sctp: fully initialize sctp_outq in sctp_outq_init
netiucv: Hold rtnl between name allocation and device registration.
...
This resolves the merge issues with drivers/base/firmware_class.c
Thanks to Ming Lei for the patch and hints on how to resolve it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cache is based on the full register map so confuses things if used
for a partial map.
Reported-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
fw_priv->buf is accessed in both request_firmware_load() and
writing to sysfs file of 'loading' context, but not protected
by 'fw_lock' entirely. The patch makes sure that access on
'fw_priv->buf' is protected by the lock.
So fixes the double abort problem reported by nirinA raseliarison:
http://lkml.org/lkml/2013/6/14/188
Reported-and-tested-by: nirinA raseliarison <nirina.raseliarison@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable <stable@vger.kernel.org> # 3.9
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device have sleep and idle states in addition to the
default state, look up these in the core and stash them in
the pinctrl state container.
Add accessor functions for pinctrl consumers to put the pins
into "default", "sleep" and "idle" states passing nothing but
the struct device * affected.
Solution suggested by Kevin Hilman, Mark Brown and Dmitry
Torokhov in response to a patch series from Hebbar
Gururaja.
Cc: Hebbar Gururaja <gururaja.hebbar@ti.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is common to access regmap registers at bit level, using
regmap_update_bits or regmap_read functions, however the end user has to
take care of a mask or shifting. This becomes overhead when such use
cases are high. Having a common function to do this is much convenient
and less error prone.
The idea of regmap_field is simple, regmap_field gives a logical
structure to bits of the regmap register, and the driver can use this
logical entity without the knowledge of the bit positions and masks all
over the code. This way code looks much neat and it need not handle the
masks, shifts every time it access the those entities.
With this new regmap_field_read/write apis the end user can setup a
regmap field using regmap_field_init and use the return regmap_field to
read write the register field without worrying about the masks or
shifts.
Also this apis will be useful for drivers which are based on regmaps,
like some clocks or pinctrls which can work on the regmap_fields
directly without having to worry about bit positions.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In converting the last remaining of_platform_driver (ibmebus) to a regular
platform driver, to_platform_driver is needed to replace
to_of_platform_driver.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This adds in a new message to the wakeup code which adds an
indication to the log that suspend was cancelled due to a wake event
occouring during the suspend sequence. It also adjusts the message
printed in suspend.c to reflect the potential that a suspend was
aborted, as opposed to a device failing to suspend.
Without these message adjustments one can end up with a kernel log
that says that a device failed to suspend with no actual device
suspend failures, which can be confusing to the log examiner.
Signed-off-by: Bernie Thompson <bhthompson@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
module reference doesn't cover direct loading path, so this patch
simply holds the module in the whole life time of request_firmware()
to fix the problem.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks no driver has the explict requirement for the two exported
API, just don't export them anymore.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the sysfs memory code to create/delete files at the time of device
and subsystem registration.
The current code creates files in the root memory directory explicitly through
the use of init_* routines. The files for each memory block are created and
deleted explicitly using the mem_[create|delete]_simple_file macros.
This patch creates attribute groups for the memory root files and files in
each memory block directory so that they are created and deleted implicitly
at subsys and device register and unregister time.
This did necessitate moving the register_memory() updating it to set the
dev.groups field.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit ddf1f0648e8c("firmware loader: fix build failure
with !CONFIG_FW_LOADER_USER_HELPER") introduces the below
warning:
drivers/base/firmware_class.c:921:13: warning:
'kill_requests_without_uevent' defined but not used [-Wunused-function]
So fix it by defining kill_requests_without_uevent() only if
CONFIG_PM_SLEEP is set.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes one build failure which is introduced by the patch
below:
driver core: firmware loader: kill FW_ACTION_NOHOTPLUG requests
before suspend
When CONFIG_FW_LOADER_USER_HELPER is unset, kill_requests_without_uevent()
should be nop because no userspace loading is involved.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "index" field of struct cpufreq_frequency_table was never an
index and isn't used at all by the cpufreq core. It only is useful
for cpufreq drivers for their internal purposes.
Many people nowadays blindly set it in ascending order with the
assumption that the core will use it, which is a mistake.
Rename it to "driver_data" as that's what its purpose is. All of its
users are updated accordingly.
[rjw: Changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Ever since commit 45f035ab9b ("CONFIG_HOTPLUG should be always on"),
it has been basically impossible to build a kernel with CONFIG_HOTPLUG
turned off. Remove all the remaining references to it.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch kills the firmware loading requests of FW_ACTION_NOHOTPLUG
before suspend to avoid blocking suspend because there is no timeout
for these requests.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Generally there are only two drivers which don't need uevent to
handle firmware loading, so don't cache these firmwares during
suspend for these drivers since doing that may block firmware
loading forever.
Both the two drivers are involved in private firmware images, so
they don't hit in direct loading too.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Standardize the indentation, and switch the order of a couple
kerneldoc entries to match the parameter order. No functional change.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I found a lot of mistakes using struct platform_driver without owner
so I make a macro instead of the function platform_driver_register.
It can set owner in it, then guys don`t care about module owner again.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move EXPORT_SYMBOL annotations so they follow immediately after the
closing function brace line.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a system goes to reboot/shutdown, it tries to disable the
usermode helper via usermodehelper_disable(). This might be blocked
when a driver tries to load a firmware beforehand and it's stuck by
some reason. For example, dell_rbu driver loads the firmware in
non-hotplug mode and waits for user-space clearing the loading sysfs
flag. If user-space doesn't clear the flag, it waits forever, thus
blocks the reboot, too.
As a workaround, in this patch, the firmware class driver registers a
reboot notifier so that it can abort all pending f/w bufs before
issuing usermodehelper_disable().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Currently all register maps with a cache need to provide a volatile
callback since the default is to assume all registers are volatile.
This is not sensible if we have a cache so change the default to be
fully cached if a cache is provided.
Signed-off-by: Mark Brown <broonie@linaro.org>
This can be used for cache types for which syncing values one by one is
equally efficient as syncing a range, such as the flat cache.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since offline_memory_block(mem) is functionally equivalent to
device_offline(&mem->dev), make the only caller of the former use
the latter instead and drop offline_memory_block() entirely.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Toshi Kani <toshi.kani@hp.com>
As noted by Tang Chen, the last_online field in struct memory_block
introduced by commit 4960e05 (Driver core: Introduce offline/online
callbacks for memory blocks) is not really necessary, because
online_pages() restores the previous state if passed ONLINE_KEEP as
the last argument. Therefore, remove that field along with the code
referring to it.
References: http://marc.info/?l=linux-kernel&m=136919777305599&w=2
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Tang Chen <tangchen@cn.fujitsu.com>
A node starting before the minimum register is no reason to reject it,
since its end could be in range. The check for the end already exists
two lines lower, so we can just remove the incorrect check.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
As reported by Dave Hansen, sysfs cpu/online shows 1 for
offlined CPUs at boot.
Fix this problem by initializing dev.offline with cpu_online()
when registering a CPU.
References: https://lkml.org/lkml/2013/5/29/403
Reported-and-tested-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
regmap-mmio uses a spinlock with spin_lock() and spin_unlock() for locking.
To be able to use the regmap API from different contexts (atomic vs non-atomic),
without the risk of race conditions, we need to use spin_lock_irqsave() and
spin_lock_irqrestore() instead. A new field, the spinlock_flags field, is added
to regmap struct to store the flags between regmap_{,un}lock_spinlock(). The
spinlock_flags field itself is also protected by the spinlock.
Thanks to Stephen Warren for the suggestion of this particular solution.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Here are 3 tiny driver core fixes for 3.10-rc2.
A needed symbol export, a change to make it easier to track down
offending sysfs files with incorrect attributes, and a klist bugfix.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlGePdAACgkQMUfUDdst+ynX3wCfbodTGeimy2GTnc5psVgXV/x4
bz8AnR6G/JNCw54meAJ5UlYJRj7Dwo09
=MNP/
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg Kroah-Hartman:
"Here are 3 tiny driver core fixes for 3.10-rc2.
A needed symbol export, a change to make it easier to track down
offending sysfs files with incorrect attributes, and a klist bugfix.
All have been in linux-next for a while"
* tag 'driver-core-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
klist: del waiter from klist_remove_waiters before wakeup waitting process
driver core: print sysfs attribute name when warning about bogus permissions
driver core: export subsys_virtual_register
The parameter passed to the regmap lock/unlock callbacks needs to be
map->lock_arg, regcache passes just map. This works fine in the case that no
custom locking callbacks are used since in this case map->lock_arg equals map,
but will break when custom locking callbacks are used. The issue was introduced
in commit 0d4529c5("regmap: make lock/unlock functions customizable") and is
fixed by this patch.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The parameter passed to the regmap lock/unlock callbacks needs to be
map->lock_arg, regcache passes just map. This works fine in the case that no
custom locking callbacks are used, since in this case map->lock_arg equals map,
but will break when custom locking callbacks are used. The issue was introduced
in commit 0d4529c5 ("regmap: make lock/unlock functions customizable") and is
fixed by this patch.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It fixes race between udev and hotplugged CPU registration by defining
"online" attribute statically, so that device_add() would create it
before notifying udev about new CPU.
Original issue report is at https://lkml.org/lkml/2012/4/30/198
"
> On Mon, Apr 30, 2012 at 11:36:23AM -0400, Konrad Rzeszutek Wilk wrote:
> > Hey Greg,
> >
> > Hoping you can help with some guidance on how to fix this.
> >
> > The issue is with CPU hotplug is that when a CPU goes up
> > it calls 'arch_register_cpu' which eventually calls
> > register_cpu. That function does these two things:
> >
> > 251 error = device_register(&cpu->dev);
> > 252 if (!error && cpu->hotpluggable)
> > 253 register_cpu_control(cpu);
> >
> > and the device_register creates a nice little SysFS directory:
> >
> > /sys/devices/system/cpu/cpu2/ which at line 251 has the 'add' attribute
> > but no 'online' attribute. udev then tries to echo 1 to the 'online'
> > and it we get:
> > udevd-work[2421]: error opening ATTR{/sys/devices/system/cpu/cpu2/online} for writing: No such file or directory
> >
> > Line 253 creates said 'online' and at that time udev [or the system admin]
> > can write 1 to 'online' and the CPU goes up.
> >
> > So .. any thoughts? Is there some way to inhibit from uevent being sent
> > until line 253 has run?
"
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"crash_notes" and "crash_notes_size" are dynamically created
with device_create_file() but aren't deleted anywhere.
Define "crash_notes" and "crash_notes_size" statically via
attribute groups so that device_register would create them
automatically and files would be destroyed when CPU is destroyed.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make it obvious to see what attribute is using bogus permissions.
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modules want to call this function, so it needs to be exported.
Reported-by: Daniel Mack <zonque@gmail.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regmap_debugfs_get_dump_start should return the offset of the register
it should start reading from, However in the current code at one point
the code does not return correct register offset.
With this patch all the returns from this function takes reg_stride in
to consideration to return correct offset.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A register write to hardware is reasonably unlikely to cause locking
dependency issues, the reason we're tainting is that unexpected changes
in the hardware configuration may confuse drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If range information has been provided then when we allocate a rbnode
within a range allocate the entire range. The goal is to minimise the
number of reallocations done when combining or extending blocks. At
present only readability and yes_ranges are taken into account, this is
expected to cover most cases efficiently.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation for being slightly smarter about how we allocate memory
factor out the node allocation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow drivers to discard parts of the register cache, for example if part
of the hardware has been reset.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce .offline() and .online() callbacks for memory_subsys
that will allow the generic device_offline() and device_online()
to be used with device objects representing memory blocks. That,
in turn, allows the ACPI subsystem to use device_offline() to put
removable memory blocks offline, if possible, before removing
memory modules holding them.
The 'online' sysfs attribute of memory block devices will attempt to
put them offline if 0 is written to it and will attempt to apply the
previously used online type when onlining them (i.e. when 1 is
written to it).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Vasilis Liaskovitis <vasilis.liaskovitis@profitbricks.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Split the ACPI processor driver into two parts, one that is
non-modular, resides in the ACPI core and handles the enumeration
and hotplug of processors and one that implements the rest of the
existing processor driver functionality.
The non-modular part uses an ACPI scan handler object to enumerate
processors on the basis of information provided by the ACPI namespace
and to hook up with the common ACPI hotplug infrastructure. It also
populates the ACPI handle of each processor device having a
corresponding object in the ACPI namespace, which allows the driver
proper to bind to those devices, and makes the driver bind to them
if it is readily available (i.e. loaded) when the scan handler's
.attach() routine is running.
There are a few reasons to make this change.
First, switching the ACPI processor driver to using the common ACPI
hotplug infrastructure reduces code duplication and size considerably,
even though a new file is created along with a header comment etc.
Second, since the common hotplug code attempts to offline devices
before starting the (non-reversible) removal procedure, it will abort
(and possibly roll back) hot-remove operations involving processors
if cpu_down() returns an error code for one of them instead of
continuing them blindly (if /sys/firmware/acpi/hotplug/force_remove
is unset). That is a more desirable behavior than what the current
code does.
Finally, the separation of the scan/hotplug part from the driver
proper makes it possible to simplify the driver's .remove() routine,
because it doesn't need to worry about the possible cleanup related
to processor removal any more (the scan/hotplug part is responsible
for that now) and can handle device removal and driver removal
symmetricaly (i.e. as appropriate).
Some user-visible changes in sysfs are made (for example, the
'sysdev' link from the ACPI device node to the processor device's
directory is gone and a 'physical_node' link is present instead
and a corresponding 'firmware_node' is present in the processor
device's directory, the processor driver is now visible under
/sys/bus/cpu/drivers/ and bound to the processor device), but
that shouldn't affect the functionality that users care about
(frequency scaling, C-states and thermal management).
Tested on my venerable Toshiba Portege R500.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Rework the CPU hotplug code in drivers/base/cpu.c to use the
generic offline/online support introduced previously instead of
its own CPU-specific code.
For this purpose, modify cpu_subsys to provide offline and online
callbacks for CONFIG_HOTPLUG_CPU set and remove the code handling
the CPU-specific 'online' sysfs attribute.
This modification is not supposed to change the user-observable
behavior of the kernel (i.e. the 'online' attribute will be present
in exactly the same place in sysfs and should trigger exactly the
same actions as before).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
In some cases, graceful hot-removal of devices is not possible,
although in principle the devices in question support hotplug.
For example, that may happen for the last CPU in the system or
for memory modules holding kernel memory.
In those cases it is nice to be able to check if the given device
can be gracefully hot-removed before triggering a removal procedure
that cannot be aborted or reversed. Unfortunately, however, the
kernel currently doesn't provide any support for that.
To address that deficiency, introduce support for offline and
online operations that can be performed on devices, respectively,
before a hot-removal and in case when it is necessary (or convenient)
to put a device back online after a successful offline (that has not
been followed by removal). The idea is that the offline will fail
whenever the given device cannot be gracefully removed from the
system and it will not be allowed to use the device after a
successful offline (until a subsequent online) in analogy with the
existing CPU offline/online mechanism.
For now, the offline and online operations are introduced at the
bus type level, as that should be sufficient for the most urgent use
cases (CPUs and memory modules). In the future, however, the
approach may be extended to cover some more complicated device
offline/online scenarios involving device drivers etc.
The lock_device_hotplug() and unlock_device_hotplug() functions are
introduced because subsequent patches need to put larger pieces of
code under device_hotplug_lock to prevent race conditions between
device offline and removal from happening.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Fix dev_pm_put_subsys_data() so that it doesn't call kfree() under
a spinlock and make it return 1 whenever it leaves NULL
power.subsys_data (regardless of the reason).
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull input updates from Dmitry Torokhov:
"Assorted fixes and cleanups to the existing drivers plus a new driver
for IMS Passenger Control Unit device they use for ther in-flight
entertainment system."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (44 commits)
Input: trackpoint - Optimize trackpoint init to use power-on reset
Input: apbps2 - convert to devm_ioremap_resource()
Input: ALPS - use %ph to print buffers
ARM - shmobile: Armadillo800EVA: Move st1232 reset pin handling
Input: st1232 - add reset pin handling
Input: st1232 - convert to devm_* infrastructure
Input: MT - handle semi-mt devices in core
Input: adxl34x - use spi_get_drvdata()
Input: ad7877 - use spi_get_drvdata() and spi_set_drvdata()
Input: ads7846 - use spi_get_drvdata() and spi_set_drvdata()
Input: ims-pcu - fix a memory leak on error
Input: sysrq - supplement reset sequence with timeout functionality
Input: tegra-kbc - support for defining row/columns based on SoC
Input: imx_keypad - switch to using managed resources
Input: arc_ps2 - add support for device tree
Input: mma8450 - fix signed 12bits to 32bits conversion
Input: eeti_ts - remove redundant null check
Input: edt-ft5x06 - remove redundant null check before kfree
Input: ad714x - add CONFIG_PM_SLEEP to suspend/resume functions
Input: adxl34x - add CONFIG_PM_SLEEP to suspend/resume functions
...
Add debugfs support to make it easier to print debug information
about the dma-buf buffers.
Cc: Dave Airlie <airlied@redhat.com>
[minor fixes on init and warning fix]
Cc: Dan Carpenter <dan.carpenter@oracle.com>
[remove double unlock in fail case]
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
For debugging purposes, it is useful to have a name-string added
while exporting buffers. Hence, dma_buf_export() is replaced with
dma_buf_export_named(), which additionally takes 'exp_name' as a
parameter.
For backward compatibility, and for lazy exporters who don't wish to
name themselves, a #define dma_buf_export() is also made available,
which adds a __FILE__ instead of 'exp_name'.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[Thanks for the idea!]
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
- ARM big.LITTLE cpufreq driver from Viresh Kumar.
- exynos5440 cpufreq driver from Amit Daniel Kachhap.
- cpufreq core cleanup and code consolidation from Viresh Kumar and
Stratos Karafotis.
- cpufreq scalability improvement from Nathan Zimmer.
- AMD "frequency sensitivity feedback" powersave bias for the ondemand
cpufreq governor from Jacob Shin.
- cpuidle code consolidation and cleanups from Daniel Lezcano.
- ARM OMAP cpuidle fixes from Santosh Shilimkar and Daniel Lezcano.
- ACPICA fixes and other improvements from Bob Moore, Jung-uk Kim,
Lv Zheng, Yinghai Lu, Tang Chen, Colin Ian King, and Linn Crosetto.
- ACPI core updates related to hotplug from Toshi Kani, Paul Bolle,
Yasuaki Ishimatsu, and Rafael J. Wysocki.
- Intel Lynxpoint LPSS (Low-Power Subsystem) support improvements
from Rafael J. Wysocki and Andy Shevchenko.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=H/se
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael J Wysocki:
- ARM big.LITTLE cpufreq driver from Viresh Kumar.
- exynos5440 cpufreq driver from Amit Daniel Kachhap.
- cpufreq core cleanup and code consolidation from Viresh Kumar and
Stratos Karafotis.
- cpufreq scalability improvement from Nathan Zimmer.
- AMD "frequency sensitivity feedback" powersave bias for the ondemand
cpufreq governor from Jacob Shin.
- cpuidle code consolidation and cleanups from Daniel Lezcano.
- ARM OMAP cpuidle fixes from Santosh Shilimkar and Daniel Lezcano.
- ACPICA fixes and other improvements from Bob Moore, Jung-uk Kim, Lv
Zheng, Yinghai Lu, Tang Chen, Colin Ian King, and Linn Crosetto.
- ACPI core updates related to hotplug from Toshi Kani, Paul Bolle,
Yasuaki Ishimatsu, and Rafael J Wysocki.
- Intel Lynxpoint LPSS (Low-Power Subsystem) support improvements from
Rafael J Wysocki and Andy Shevchenko.
* tag 'pm+acpi-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (192 commits)
cpufreq: Revert incorrect commit 5800043
cpufreq: MAINTAINERS: Add co-maintainer
cpuidle: add maintainer entry
ACPI / thermal: do not always return THERMAL_TREND_RAISING for active trip points
ARM: s3c64xx: cpuidle: use init/exit common routine
cpufreq: pxa2xx: initialize variables
ACPI: video: correct acpi_video_bus_add error processing
SH: cpuidle: use init/exit common routine
ARM: S5pv210: compiling issue, ARM_S5PV210_CPUFREQ needs CONFIG_CPU_FREQ_TABLE=y
ACPI: Fix wrong parameter passed to memblock_reserve
cpuidle: fix comment format
pnp: use %*phC to dump small buffers
isapnp: remove debug leftovers
ARM: imx: cpuidle: use init/exit common routine
ARM: davinci: cpuidle: use init/exit common routine
ARM: kirkwood: cpuidle: use init/exit common routine
ARM: calxeda: cpuidle: use init/exit common routine
ARM: tegra: cpuidle: use init/exit common routine for tegra3
ARM: tegra: cpuidle: use init/exit common routine for tegra2
ARM: OMAP4: cpuidle: use init/exit common routine
...
Pull workqueue updates from Tejun Heo:
"A lot of activities on workqueue side this time. The changes achieve
the followings.
- WQ_UNBOUND workqueues - the workqueues which are per-cpu - are
updated to be able to interface with multiple backend worker pools.
This involved a lot of churning but the end result seems actually
neater as unbound workqueues are now a lot closer to per-cpu ones.
- The ability to interface with multiple backend worker pools are
used to implement unbound workqueues with custom attributes.
Currently the supported attributes are the nice level and CPU
affinity. It may be expanded to include cgroup association in
future. The attributes can be specified either by calling
apply_workqueue_attrs() or through /sys/bus/workqueue/WQ_NAME/* if
the workqueue in question is exported through sysfs.
The backend worker pools are keyed by the actual attributes and
shared by any workqueues which share the same attributes. When
attributes of a workqueue are changed, the workqueue binds to the
worker pool with the specified attributes while leaving the work
items which are already executing in its previous worker pools
alone.
This allows converting custom worker pool implementations which
want worker attribute tuning to use workqueues. The writeback pool
is already converted in block tree and there are a couple others
are likely to follow including btrfs io workers.
- WQ_UNBOUND's ability to bind to multiple worker pools is also used
to make it NUMA-aware. Because there's no association between work
item issuer and the specific worker assigned to execute it, before
this change, using unbound workqueue led to unnecessary cross-node
bouncing and it couldn't be helped by autonuma as it requires tasks
to have implicit node affinity and workers are assigned randomly.
After these changes, an unbound workqueue now binds to multiple
NUMA-affine worker pools so that queued work items are executed in
the same node. This is turned on by default but can be disabled
system-wide or for individual workqueues.
Crypto was requesting NUMA affinity as encrypting data across
different nodes can contribute noticeable overhead and doing it
per-cpu was too limiting for certain cases and IO throughput could
be bottlenecked by one CPU being fully occupied while others have
idle cycles.
While the new features required a lot of changes including
restructuring locking, it didn't complicate the execution paths much.
The unbound workqueue handling is now closer to per-cpu ones and the
new features are implemented by simply associating a workqueue with
different sets of backend worker pools without changing queue,
execution or flush paths.
As such, even though the amount of change is very high, I feel
relatively safe in that it isn't likely to cause subtle issues with
basic correctness of work item execution and handling. If something
is wrong, it's likely to show up as being associated with worker pools
with the wrong attributes or OOPS while workqueue attributes are being
changed or during CPU hotplug.
While this creates more backend worker pools, it doesn't add too many
more workers unless, of course, there are many workqueues with unique
combinations of attributes. Assuming everything else is the same,
NUMA awareness costs an extra worker pool per NUMA node with online
CPUs.
There are also a couple things which are being routed outside the
workqueue tree.
- block tree pulled in workqueue for-3.10 so that writeback worker
pool can be converted to unbound workqueue with sysfs control
exposed. This simplifies the code, makes writeback workers
NUMA-aware and allows tuning nice level and CPU affinity via sysfs.
- The conversion to workqueue means that there's no 1:1 association
between a specific worker, which makes writeback folks unhappy as
they want to be able to tell which filesystem caused a problem from
backtrace on systems with many filesystems mounted. This is
resolved by allowing work items to set debug info string which is
printed when the task is dumped. As this change involves unifying
implementations of dump_stack() and friends in arch codes, it's
being routed through Andrew's -mm tree."
* 'for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (84 commits)
workqueue: use kmem_cache_free() instead of kfree()
workqueue: avoid false negative WARN_ON() in destroy_workqueue()
workqueue: update sysfs interface to reflect NUMA awareness and a kernel param to disable NUMA affinity
workqueue: implement NUMA affinity for unbound workqueues
workqueue: introduce put_pwq_unlocked()
workqueue: introduce numa_pwq_tbl_install()
workqueue: use NUMA-aware allocation for pool_workqueues
workqueue: break init_and_link_pwq() into two functions and introduce alloc_unbound_pwq()
workqueue: map an unbound workqueues to multiple per-node pool_workqueues
workqueue: move hot fields of workqueue_struct to the end
workqueue: make workqueue->name[] fixed len
workqueue: add workqueue->unbound_attrs
workqueue: determine NUMA node of workers accourding to the allowed cpumask
workqueue: drop 'H' from kworker names of unbound worker pools
workqueue: add wq_numa_tbl_len and wq_numa_possible_cpumask[]
workqueue: move pwq_pool_locking outside of get/put_unbound_pool()
workqueue: fix memory leak in apply_workqueue_attrs()
workqueue: fix unbound workqueue attrs hashing / comparison
workqueue: fix race condition in unbound workqueue free path
workqueue: remove pwq_lock which is no longer used
...
Merge first batch of fixes from Andrew Morton:
- A couple of kthread changes
- A few minor audit patches
- A number of fbdev patches. Florian remains AWOL so I'm picking up
some of these.
- A few kbuild things
- ocfs2 updates
- Almost all of the MM queue
(And in the meantime, I already have the second big batch from Andrew
pending in my mailbox ;^)
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (149 commits)
memcg: take reference before releasing rcu_read_lock
mem hotunplug: fix kfree() of bootmem memory
mmKconfig: add an option to disable bounce
mm, nobootmem: do memset() after memblock_reserve()
mm, nobootmem: clean-up of free_low_memory_core_early()
fs/buffer.c: remove unnecessary init operation after allocating buffer_head.
numa, cpu hotplug: change links of CPU and node when changing node number by onlining CPU
mm: fix memory_hotplug.c printk format warning
mm: swap: mark swap pages writeback before queueing for direct IO
swap: redirty page if page write fails on swap file
mm, memcg: give exiting processes access to memory reserves
thp: fix huge zero page logic for page with pfn == 0
memcg: avoid accessing memcg after releasing reference
fs: fix fsync() error reporting
memblock: fix missing comment of memblock_insert_region()
mm: Remove unused parameter of pages_correctly_reserved()
firmware, memmap: fix firmware_map_entry leak
mm/vmstat: add note on safety of drain_zonestat
mm: thp: add split tail pages to shrink page list in page reclaim
mm: allow for outstanding swap writeback accounting
...
In user visible terms just a couple of enhancements here, though there
was a moderate amount of refactoring required in order to support the
register cache sync performance improvements.
- Support for block and asynchronous I/O during register cache syncing;
this provides a use case dependant performance improvement.
- Additional debugfs information on the memory consuption and register
set.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=RG1W
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"In user visible terms just a couple of enhancements here, though there
was a moderate amount of refactoring required in order to support the
register cache sync performance improvements.
- Support for block and asynchronous I/O during register cache
syncing; this provides a use case dependant performance
improvement.
- Additional debugfs information on the memory consuption and
register set"
* tag 'regmap-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (23 commits)
regmap: don't corrupt work buffer in _regmap_raw_write()
regmap: cache: Fix format specifier in dev_dbg
regmap: cache: Make regcache_sync_block_raw static
regmap: cache: Write consecutive registers in a single block write
regmap: cache: Split raw and non-raw syncs
regmap: cache: Factor out block sync
regmap: cache: Factor out reg_present support from rbtree cache
regmap: cache: Use raw I/O to sync rbtrees if we can
regmap: core: Provide regmap_can_raw_write() operation
regmap: cache: Provide a get address of value operation
regmap: Cut down on the average # of nodes in the rbtree cache
regmap: core: Make raw write available to regcache
regmap: core: Warn on invalid operation combinations
regmap: irq: Clarify error message when we fail to request primary IRQ
regmap: rbtree Expose total memory consumption in the rbtree debugfs entry
regmap: debugfs: Add a registers `range' file
regmap: debugfs: Simplify calculation of `c->max_reg'
regmap: cache: Store caches in native register format where possible
regmap: core: Split out in place value parsing
regmap: cache: Use regcache_get_value() to check if we updated
...
nr_pages is not used in pages_correctly_reserved().
So remove it.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: Wang Shilong <wangsl-fnst@cn.fujitsu.com>
Reviewed-by: Wen Congyang <wency@cn.fujitsu.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__remove_pages() is only necessary for CONFIG_MEMORY_HOTREMOVE. PowerPC
pseries will return -EOPNOTSUPP if unsupported.
Adding an #ifdef causes several other functions it depends on to also
become unnecessary, which saves in .text when disabled (it's disabled in
most defconfigs besides powerpc, including x86). remove_memory_block()
becomes static since it is not referenced outside of
drivers/base/memory.c.
Build tested on x86 and powerpc with CONFIG_MEMORY_HOTREMOVE both enabled
and disabled.
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Squishes a warning which my change to hotplug_memory_notifier() added.
I want to keep that warning, because it is punishment for failnig to check
the hotplug_memory_notifier() return value.
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pm-assorted:
PM / OPP: add documentation to RCU head in struct opp
PM / sleep: invalidate TEST_CPUS and TEST_CORE support for freeze state
PM / sleep: add TEST_PLATFORM support for freeze state
_regmap_raw_write() contains code to call regcache_write() to write
values to the cache. That code calls memcpy() to copy the value data to
the start of the work_buf. However, at least when _regmap_raw_write() is
called from _regmap_bus_raw_write(), the value data is in the work_buf,
and this memcpy() operation may over-write part of that value data,
depending on the value of reg_bytes + pad_bytes. At least when using
reg_bytes==1 and pad_bytes==0, corruption of the value data does occur.
To solve this, remove the memcpy() operation, and modify the subsequent
.parse_val() call to parse the original value buffer directly.
At least in the case of 8-bit register address and 16-bit values, and
writes of single registers at a time, this memcpy-then-parse combination
used to cancel each-other out; for a work-buffer containing xx 89 03,
the memcpy changed it to 89 03 03, and the parse_val changed it back to
89 89 03, thus leaving the value uncorrupted. This appears completely
accidental though. Since commit 8a819ff "regmap: core: Split out in
place value parsing", .parse_val only returns the parsed value, and does
not modify the buffer, and hence does not (accidentally) undo the
corruption caused by memcpy(). This caused bogus values to get written
to HW, thus preventing e.g. audio playback on systems with a WM8903
CODEC. This patch fixes that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When genpd prepares for a system suspend it will fetch a runtime
reference for the device. When returning it we now use the
asyncronous runtime PM API. Thus we don't have to wait for the
device to become idle|suspended before we move on and handle the
next device in queue.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For irq safe devices return the runtime reference for the parent
by using the asyncronous runtime PM API. Thus we don't have to
wait for it to become idle|suspended. Instead we can move on and
handle the next device in queue.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the asyncronous runtime PM API when returning the runtime
reference for the device after the system resume is completed.
By using the asyncronous runtime PM API we don't have to wait
for each an every device to become idle|suspended. Instead we
can move on and handle the next device in queue.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Putting devices into idle|suspend in a synchronous manner means we are
waiting for each device to become idle|suspended before the probe|release
is fully done.
This patch switch to use the asynchronous runtime PM API:s instead and
thus improves the parallelism since we can move on and handle the next
device in queue in an earlier phase.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that devtmpfs is caring about uid/gid, we need to use the correct
internal types so users who have USER_NS enabled will have things work
properly for them.
Thanks to Eric for pointing this out, and the patch review.
Reported-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_UIDGID_STRICT_TYPE_CHECKS is enalbed, the below compile
failure will be triggered:
drivers/base/devtmpfs.c: In function 'handle_create':
drivers/base/devtmpfs.c:214:19: error: incompatible types when assigning to type 'kuid_t' from type 'uid_t'
drivers/base/devtmpfs.c:215:19: error: incompatible types when assigning to type 'kgid_t' from type 'gid_t'
make[2]: *** [drivers/base/devtmpfs.o] Error 1
This patch fixes the compile failure.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Kay Sievers <kay@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a sparse warning, and is a good idea given that the
devtmpfs_init() prototype is in this file.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit bc8ce4 (regmap: don't corrupt work buffer in
_regmap_raw_write()) since it turns out that it can cause issues when
taken in isolation from the other changes in -next that lead to its
discovery. On the basis that nobody noticed the problems for quite some
time without that subsequent work let's drop it from v3.9.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some drivers want to tell userspace what uid and gid should be used for
their device nodes, so allow that information to percolate through the
driver core to userspace in order to make this happen. This means that
some systems (i.e. Android and friends) will not need to even run a
udev-like daemon for their device node manager and can just rely in
devtmpfs fully, reducing their footprint even more.
Signed-off-by: Kay Sievers <kay@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dde8437 (PM / OPP: RCU reclaim) introduced rcu_head for
struct opp. This aids freeing using kfree_rcu. However, we missed
adding documentation for the same. This generates kernel doc warning:
Warning(drivers/base/power/opp.c:70): No description found for
parameter 'head'
Add documentation as appropriate.
[rjw: Changelog]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix format specifier in dev_dbg and suppress the following warning
drivers/base/regmap/regcache.c: In function
‘regcache_sync_block_raw_flush’:
drivers/base/regmap/regcache.c:593:2: warning: format ‘%d’ expects
argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regcache_sync_block_raw is used only in this file. Hence make it static.
Silences the following warning:
drivers/base/regmap/regcache.c:608:5: warning:
symbol 'regcache_sync_block_raw' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
- Revert of a recent cpuidle change that caused Nehalem machines
to hang on boot from Alex Shi.
- USB power management fix addressing a crash in the port device
object's release routine from Rafael J. Wysocki.
- Device PM QoS fix for a potential deadlock related to sysfs
interface from Rafael J. Wysocki.
- Fix for a cpufreq crash when the /cpus Device Tree node is missing
from Paolo Pisati.
- Fix for a build issue on ia64 related to the Boot Graphics Resource
Table (BGRT) from Tony Luck.
- Two fixes for ACPI handles being set incorrectly for device
objects that don't correspond to any ACPI namespace nodes in
the I2C and SPI subsystems from Rafael J. Wysocki.
- Fix for compiler warnings related to CONFIG_PM_DEVFREQ being
unset from Rajagopal Venkat.
- Fix for a symbol definition typo in cpufreq_governor.h from
Borislav Petkov.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=s/w4
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Revert of a recent cpuidle change that caused Nehalem machines to
hang on boot from Alex Shi.
- USB power management fix addressing a crash in the port device
object's release routine from Rafael J Wysocki.
- Device PM QoS fix for a potential deadlock related to sysfs interface
from Rafael J Wysocki.
- Fix for a cpufreq crash when the /cpus Device Tree node is missing
from Paolo Pisati.
- Fix for a build issue on ia64 related to the Boot Graphics Resource
Table (BGRT) from Tony Luck.
- Two fixes for ACPI handles being set incorrectly for device objects
that don't correspond to any ACPI namespace nodes in the I2C and SPI
subsystems from Rafael J Wysocki.
- Fix for compiler warnings related to CONFIG_PM_DEVFREQ being unset
from Rajagopal Venkat.
- Fix for a symbol definition typo in cpufreq_governor.h from Borislav
Petkov.
* tag 'pm+acpi-3.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / BGRT: Don't let users configure BGRT on non X86 systems
cpuidle / ACPI: recover percpu ACPI processor cstate
ACPI / I2C: Use parent's ACPI_HANDLE() in acpi_i2c_register_devices()
cpufreq: Correct header guards typo
ACPI / SPI: Use parent's ACPI_HANDLE() in acpi_register_spi_devices()
cpufreq: check OF node /cpus presence before dereferencing it
PM / devfreq: Fix compiler warnings for CONFIG_PM_DEVFREQ unset
PM / QoS: Avoid possible deadlock related to sysfs access
USB / PM: Don't try to hide PM QoS flags from usb_port_device_release()
commit eca4549f57 "sysfs: Add crash_notes_size to export percpu
note size" adds a printk that outputs a size_t value as %lu
when it should be %zu, resulting in this warning.
drivers/base/cpu.c: In function 'show_crash_notes_size':
drivers/base/cpu.c:142:2: warning: format '%lu' expects argument of type 'long unsigned int', but argument 3 has type 'unsigned int' [-Wformat=]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRWLTrAAoJEHm+PkMAQRiGe8oH/iMy48mecVWvxVZn74Tx3Cef
xmW/PnAIj28EhSPqK49N/Ow6AfQToFKf7AP0ge20KAf5teTq95AY+tH74DAANt8F
BjKXXTZiR5xwBvRkq7CR5wDcCvEcBAAz8fgTEd6SEDB2d2VXFf5eKdKUqt1avTCh
Z6Hup5kuwX+ddtwY2DCBXtp2n6fL0Rm5yLzY1A3OOBye1E7VyLTF7M5BR603Q44P
4kRLxn8+R7jy3hTuZIhAeoS8TKUoBwVk7DmKxEzrhTHZVOmvwE9lEHybRnIyOpd/
k1JnbRbiPsLsCVFOn10SQkGDAIk00lro3tuWP2C1ljERiD/OOh5Ui9nXYAhMkbI=
=q15K
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc5' into wq/for-3.10
Writeback conversion to workqueue will be based on top of wq/for-3.10
branch to take advantage of custom attrs and NUMA support for unbound
workqueues. Mainline currently contains two commits which result in
non-trivial merge conflicts with wq/for-3.10 and because
block/for-3.10/core is based on v3.9-rc3 which contains one of the
conflicting commits, we need a pre-merge-window merge anyway. Let's
pull v3.9-rc5 into wq/for-3.10 so that the block tree doesn't suffer
from workqueue merge conflicts.
The two conflicts and their resolutions:
* e68035fb65 ("workqueue: convert to idr_alloc()") in mainline changes
worker_pool_assign_id() to use idr_alloc() instead of the old idr
interface. worker_pool_assign_id() goes through multiple locking
changes in wq/for-3.10 causing the following conflict.
static int worker_pool_assign_id(struct worker_pool *pool)
{
int ret;
<<<<<<< HEAD
lockdep_assert_held(&wq_pool_mutex);
do {
if (!idr_pre_get(&worker_pool_idr, GFP_KERNEL))
return -ENOMEM;
ret = idr_get_new(&worker_pool_idr, pool, &pool->id);
} while (ret == -EAGAIN);
=======
mutex_lock(&worker_pool_idr_mutex);
ret = idr_alloc(&worker_pool_idr, pool, 0, 0, GFP_KERNEL);
if (ret >= 0)
pool->id = ret;
mutex_unlock(&worker_pool_idr_mutex);
>>>>>>> c67bf5361e
return ret < 0 ? ret : 0;
}
We want locking from the former and idr_alloc() usage from the
latter, which can be combined to the following.
static int worker_pool_assign_id(struct worker_pool *pool)
{
int ret;
lockdep_assert_held(&wq_pool_mutex);
ret = idr_alloc(&worker_pool_idr, pool, 0, 0, GFP_KERNEL);
if (ret >= 0) {
pool->id = ret;
return 0;
}
return ret;
}
* eb2834285c ("workqueue: fix possible pool stall bug in
wq_unbind_fn()") updated wq_unbind_fn() such that it has single
larger for_each_std_worker_pool() loop instead of two separate loops
with a schedule() call inbetween. wq/for-3.10 renamed
pool->assoc_mutex to pool->manager_mutex causing the following
conflict (earlier function body and comments omitted for brevity).
static void wq_unbind_fn(struct work_struct *work)
{
...
spin_unlock_irq(&pool->lock);
<<<<<<< HEAD
mutex_unlock(&pool->manager_mutex);
}
=======
mutex_unlock(&pool->assoc_mutex);
>>>>>>> c67bf5361e
schedule();
<<<<<<< HEAD
for_each_cpu_worker_pool(pool, cpu)
=======
>>>>>>> c67bf5361e
atomic_set(&pool->nr_running, 0);
spin_lock_irq(&pool->lock);
wake_up_worker(pool);
spin_unlock_irq(&pool->lock);
}
}
The resolution is mostly trivial. We want the control flow of the
latter with the rename of the former.
static void wq_unbind_fn(struct work_struct *work)
{
...
spin_unlock_irq(&pool->lock);
mutex_unlock(&pool->manager_mutex);
schedule();
atomic_set(&pool->nr_running, 0);
spin_lock_irq(&pool->lock);
wake_up_worker(pool);
spin_unlock_irq(&pool->lock);
}
}
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit b81ea1b (PM / QoS: Fix concurrency issues and memory leaks in
device PM QoS) put calls to pm_qos_sysfs_add_latency(),
pm_qos_sysfs_add_flags(), pm_qos_sysfs_remove_latency(), and
pm_qos_sysfs_remove_flags() under dev_pm_qos_mtx, which was a
mistake, because it may lead to deadlocks in some situations.
For example, if pm_qos_remote_wakeup_store() is run in parallel
with dev_pm_qos_constraints_destroy(), they may deadlock in the
following way:
======================================================
[ INFO: possible circular locking dependency detected ]
3.9.0-rc4-next-20130328-sasha-00014-g91a3267 #319 Tainted: G W
-------------------------------------------------------
trinity-child6/12371 is trying to acquire lock:
(s_active#54){++++.+}, at: [<ffffffff81301631>] sysfs_addrm_finish+0x31/0x60
but task is already holding lock:
(dev_pm_qos_mtx){+.+.+.}, at: [<ffffffff81f07cc3>] dev_pm_qos_constraints_destroy+0x23/0x250
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (dev_pm_qos_mtx){+.+.+.}:
[<ffffffff811811da>] lock_acquire+0x1aa/0x240
[<ffffffff83dab809>] __mutex_lock_common+0x59/0x5e0
[<ffffffff83dabebf>] mutex_lock_nested+0x3f/0x50
[<ffffffff81f07f2f>] dev_pm_qos_update_flags+0x3f/0xc0
[<ffffffff81f05f4f>] pm_qos_remote_wakeup_store+0x3f/0x70
[<ffffffff81efbb43>] dev_attr_store+0x13/0x20
[<ffffffff812ffdaa>] sysfs_write_file+0xfa/0x150
[<ffffffff8127f2c1>] __kernel_write+0x81/0x150
[<ffffffff812afc2d>] write_pipe_buf+0x4d/0x80
[<ffffffff812af57c>] splice_from_pipe_feed+0x7c/0x120
[<ffffffff812afa25>] __splice_from_pipe+0x45/0x80
[<ffffffff812b14fc>] splice_from_pipe+0x4c/0x70
[<ffffffff812b1538>] default_file_splice_write+0x18/0x30
[<ffffffff812afae3>] do_splice_from+0x83/0xb0
[<ffffffff812afb2e>] direct_splice_actor+0x1e/0x20
[<ffffffff812b0277>] splice_direct_to_actor+0xe7/0x200
[<ffffffff812b15bc>] do_splice_direct+0x4c/0x70
[<ffffffff8127eda9>] do_sendfile+0x169/0x300
[<ffffffff8127ff94>] SyS_sendfile64+0x64/0xb0
[<ffffffff83db7d18>] tracesys+0xe1/0xe6
-> #0 (s_active#54){++++.+}:
[<ffffffff811800cf>] __lock_acquire+0x15bf/0x1e50
[<ffffffff811811da>] lock_acquire+0x1aa/0x240
[<ffffffff81300aa2>] sysfs_deactivate+0x122/0x1a0
[<ffffffff81301631>] sysfs_addrm_finish+0x31/0x60
[<ffffffff812ff77f>] sysfs_hash_and_remove+0x7f/0xb0
[<ffffffff813035a1>] sysfs_unmerge_group+0x51/0x70
[<ffffffff81f068f4>] pm_qos_sysfs_remove_flags+0x14/0x20
[<ffffffff81f07490>] __dev_pm_qos_hide_flags+0x30/0x70
[<ffffffff81f07cd5>] dev_pm_qos_constraints_destroy+0x35/0x250
[<ffffffff81f06931>] dpm_sysfs_remove+0x11/0x50
[<ffffffff81efcf6f>] device_del+0x3f/0x1b0
[<ffffffff81efd128>] device_unregister+0x48/0x60
[<ffffffff82d4083c>] usb_hub_remove_port_device+0x1c/0x20
[<ffffffff82d2a9cd>] hub_disconnect+0xdd/0x160
[<ffffffff82d36ab7>] usb_unbind_interface+0x67/0x170
[<ffffffff81f001a7>] __device_release_driver+0x87/0xe0
[<ffffffff81f00559>] device_release_driver+0x29/0x40
[<ffffffff81effc58>] bus_remove_device+0x148/0x160
[<ffffffff81efd07f>] device_del+0x14f/0x1b0
[<ffffffff82d344f9>] usb_disable_device+0xf9/0x280
[<ffffffff82d34ff8>] usb_set_configuration+0x268/0x840
[<ffffffff82d3a7fc>] usb_remove_store+0x4c/0x80
[<ffffffff81efbb43>] dev_attr_store+0x13/0x20
[<ffffffff812ffdaa>] sysfs_write_file+0xfa/0x150
[<ffffffff8127f71d>] do_loop_readv_writev+0x4d/0x90
[<ffffffff8127f999>] do_readv_writev+0xf9/0x1e0
[<ffffffff8127faba>] vfs_writev+0x3a/0x60
[<ffffffff8127fc60>] SyS_writev+0x50/0xd0
[<ffffffff83db7d18>] tracesys+0xe1/0xe6
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(dev_pm_qos_mtx);
lock(s_active#54);
lock(dev_pm_qos_mtx);
lock(s_active#54);
*** DEADLOCK ***
To avoid that, remove the calls to functions mentioned above from
under dev_pm_qos_mtx and introduce a separate lock to prevent races
between functions that add or remove device PM QoS sysfs attributes
from happening.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When syncing blocks of data using raw writes combine the writes into a
single block write, saving us bus overhead for setup, addressing and
teardown.
Currently the block write is done unconditionally as it is expected that
hardware which has a register format which can support raw writes will
support auto incrementing writes, this decision may need to be revised in
future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
For code clarity after implementing block writes split out the raw and
non-raw I/O sync implementations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
The idea of holding blocks of registers in device format is shared between
at least rbtree and lzo cache formats so split out the loop that does the
sync from the rbtree code so optimisations on it can be reused.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
The idea of maintaining a bitmap of present registers is something that
can usefully be used by other cache types that maintain blocks of cached
registers so move the code out of the rbtree cache and into the generic
regcache code.
Refactor the interface slightly as we go to wrap the set bit and enlarge
bitmap operations (since we never do one without the other) and make it
more robust for reads of uncached registers by bounds checking before we
look at the bitmap.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
For percpu notes, we are exporting only address and not size. So
the userspace tool kexec-tools is putting an upper limit of 1024
and putting the value in p_memsz and p_filesz fields. So the patch
add the new sysfile crash_notes_size to export the exact percpu
note size and let the kexec-tools parse it intead of using 1024.
The idea came from Vivek Goyal. And a later patch will be sent to
kexec-tools to let it parse the size.
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will bring no meaningful benefit by itself, it is done as a separate
commit to aid bisection if there are problems with the following commits
adding support for coalescing adjacent writes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mainly useful internally but exported since this is a public API that's
being checked for.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide a helper to do the size based index into a block of registers and
use it when reading a value.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch aims to bring down the average number of nodes
in the rbtree cache and increase the average number of registers
per node. This should improve general lookup and traversal times.
This is achieved by setting the minimum size of a block within the
rbnode to the size of the rbnode itself. This will essentially
cache possibly non-existent registers so to combat this scenario,
we keep a separate bitmap in memory which keeps track of which register
exists. The memory overhead of this change is likely in the order of
~5-10%, possibly less depending on the register file layout. On my test
system with a bitmap of ~4300 bits and a relatively sparse register
layout, the memory requirements for the entire cache did not increase
(the cutting down of nodes which was about 50% of the original number
compensated the situation).
A second patch that can be built on top of this can look at the
ratio `sizeof(*rbnode) / map->cache_word_size' in order to suitably
adjust the block length of each block.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows the cache to sync values directly to the device when stored
in native format and also allows asynchronous I/O.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
_regmap_raw_write() contains code to call regcache_write() to write
values to the cache. That code calls memcpy() to copy the value data to
the start of the work_buf. However, at least when _regmap_raw_write() is
called from _regmap_bus_raw_write(), the value data is in the work_buf,
and this memcpy() operation may over-write part of that value data,
depending on the value of reg_bytes + pad_bytes. At least when using
reg_bytes==1 and pad_bytes==0, corruption of the value data does occur.
To solve this, remove the memcpy() operation, and modify the subsequent
.parse_val() call to parse the original value buffer directly.
At least in the case of 8-bit register address and 16-bit values, and
writes of single registers at a time, this memcpy-then-parse combination
used to cancel each-other out; for a work-buffer containing xx 89 03,
the memcpy changed it to 89 03 03, and the parse_val changed it back to
89 89 03, thus leaving the value uncorrupted. This appears completely
accidental though. Since commit 8a819ff "regmap: core: Split out in
place value parsing", .parse_val only returns the parsed value, and does
not modify the buffer, and hence does not (accidentally) undo the
corruption caused by memcpy(). This caused bogus values to get written
to HW, thus preventing e.g. audio playback on systems with a WM8903
CODEC. This patch fixes that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Display the name for the chip rather than just the primary IRQ so it is
clearer what exactly has failed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRRkrbAAoJEHm+PkMAQRiGy3oH/jrbHinYs0auurANgx4TdtWT
/WNajstKBqLOJJ6cnTR7sOqwOVlptt65EbbTs+qGyZ2Z2W/Lg0BMenHvNHo4ER8C
e7UbMdBCSLKBjAMKh1XCoZscGv4Exm8WRH3Vc5yP0Hafj3EzSAVLY1dta9WKKoQi
bh7D1ErUlbU1zczA1w5YbPF0LqFKRvyZOwebMCCAKAxv5wWAxmbcPNxVR4sufkjg
k6TkQ2ysgWivZAfy3tJYOcxiEu7ahpZVEuYdlZEJQXHRQUfoNljQlOp4BqKsYUai
5A0kaf2VpKay/7pkhvTfBBcF/jFJ68pYP6gQ2ThNdr0b5kOiAfMWj030Xyngnhg=
=iO9t
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc3' into next
Merge with mainline to bring in module_platform_driver_probe() and
devm_ioremap_resource().
Whenever a struct device_attribute is registered
with mismatched permissions - read permission without
a show routine or write permission without store
routine - we will issue a big warning so we catch
those early enough.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last register block, which falls into the specified range, is not handled
correctly. The formula which calculates the number of register which should be
synced is inverse (and off by one). E.g. if all registers in that block should
be synced only one is synced, and if only one should be synced all (but one) are
synced. To calculate the number of registers that need to be synced we need to
subtract the number of the first register in the block from the max register
number and add one. This patch updates the code accordingly.
The issue was introduced in commit ac8d91c ("regmap: Supply ranges to the sync
operations").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Provide a feel of how much overhead the rbtree cache adds to
the game.
[Slightly reworded output in debugfs -- broonie]
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Kay tells me the most appropriate place to expose workqueues to
userland would be /sys/devices/virtual/workqueues/WQ_NAME which is
symlinked to /sys/bus/workqueue/devices/WQ_NAME and that we're lacking
a way to do that outside of driver core as virtual_device_parent()
isn't exported and there's no inteface to conveniently create a
virtual subsystem.
This patch implements subsys_virtual_register() by factoring out
subsys_register() from subsys_system_register() and using it with
virtual_device_parent() as the origin directory. It's identical to
subsys_system_register() other than the origin directory but we aren't
gonna restrict the device names which should be used under it.
This will be used to expose workqueue attributes to userland.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
In the rbtree code we are exposing statistics relating to the
number of nodes/registers of the rbtree cache for each of the
devices. Ensure that `map->debugfs' has been initialized before
we attempt to initialize the debugfs entry for the rbtree cache.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
- Two fixes for the new intel_pstate driver from Dirk Brandewie.
- Fix for incorrect usage of the .find_bridge() callback from struct
acpi_bus_type in the USB core and subsequent removal of that
callback from Rafael J. Wysocki.
- ACPI processor driver cleanups from Chen Gang and Syam Sidhardhan.
- ACPI initialization and error messages fix from Joe Perches.
- Operating Performance Points documentation improvement from
Nishanth Menon.
- Fixes for memory leaks and potential concurrency issues and sysfs
attributes leaks during device removal in the core device PM QoS
code from Rafael J. Wysocki.
- Calxeda Highbank cpufreq driver simplification from Emilio López.
- cpufreq comment cleanup from Namhyung Kim.
- Fix for a section mismatch in Calxeda Highbank interprocessor
communication code from Mark Langsdorf (this is not a PM fix
strictly speaking, but the code in question went in through the
PM tree).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=9vaj
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael J Wysocki:
- Two fixes for the new intel_pstate driver from Dirk Brandewie.
- Fix for incorrect usage of the .find_bridge() callback from struct
acpi_bus_type in the USB core and subsequent removal of that callback
from Rafael J Wysocki.
- ACPI processor driver cleanups from Chen Gang and Syam Sidhardhan.
- ACPI initialization and error messages fix from Joe Perches.
- Operating Performance Points documentation improvement from Nishanth
Menon.
- Fixes for memory leaks and potential concurrency issues and sysfs
attributes leaks during device removal in the core device PM QoS code
from Rafael J Wysocki.
- Calxeda Highbank cpufreq driver simplification from Emilio López.
- cpufreq comment cleanup from Namhyung Kim.
- Fix for a section mismatch in Calxeda Highbank interprocessor
communication code from Mark Langsdorf (this is not a PM fix strictly
speaking, but the code in question went in through the PM tree).
* tag 'pm+acpi-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq / intel_pstate: Do not load on VM that does not report max P state.
cpufreq / intel_pstate: Fix intel_pstate_init() error path
ACPI / glue: Drop .find_bridge() callback from struct acpi_bus_type
ACPI / glue: Add .match() callback to struct acpi_bus_type
ACPI / porocessor: Beautify code, pr->id is u32 which is never < 0
ACPI / processor: Remove redundant NULL check before kfree
ACPI / Sleep: Avoid interleaved message on errors
PM / QoS: Remove device PM QoS sysfs attributes at the right place
PM / QoS: Fix concurrency issues and memory leaks in device PM QoS
cpufreq: highbank: do not initialize array with a loop
PM / OPP: improve introductory documentation
cpufreq: Fix a typo in comment
mailbox, pl320-ipc: remove __init from probe function
A simple fix to stop us leaking a runtime PM reference in the case where
we fail to enable a device.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=D1mN
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap PM fix from Mark Brown:
"A simple fix to stop us leaking a runtime PM reference in the case
where we fail to enable a device."
* tag 'regmap-v3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: irq: call pm_runtime_put in pm_runtime_get_sync failed case
Device PM QoS sysfs attributes, if present during device removal,
are removed from within device_pm_remove(), which is too late,
since dpm_sysfs_remove() has already removed the whole attribute
group they belonged to. However, moving the removal of those
attributes to dpm_sysfs_remove() alone is not sufficient, because
in theory they still can be re-added right after being removed by it
(the device's driver is still bound to it at that point).
For this reason, move the entire desctruction of device PM QoS
constraints to dpm_sysfs_remove() and make it prevent any new
constraints from being added after it has run. Also, move the
initialization of the power.qos field in struct device to
device_pm_init_common() and drop the no longer needed
dev_pm_qos_constraints_init().
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The current device PM QoS code assumes that certain functions will
never be called in parallel with each other (for example, it is
assumed that dev_pm_qos_expose_flags() won't be called in parallel
with dev_pm_qos_hide_flags() for the same device and analogously
for the latency limit), which may be overly optimistic. Moreover,
dev_pm_qos_expose_flags() and dev_pm_qos_expose_latency_limit()
leak memory in error code paths (req needs to be freed on errors)
and __dev_pm_qos_drop_user_request() forgets to free the request.
To fix the above issues put more things under the device PM QoS
mutex to make them mutually exclusive and add the missing freeing
of memory.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This file lists the register ranges in the register map. The condition
to split the range is based on whether the block is readable or not.
Ensure that we lock the `debugfs_off_cache' list whenever we access
and modify the list. There is a possible race otherwise between the
read() operations of the `registers' file and the `range' file.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't need to use any of the file position information
to calculate the base and max register of each block. Just
use the counter directly.
Set `i = base' at the top to avoid GCC flow analysis bugs. The
value of `i' can never be undefined or 0 in the if (c) { ... }.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the value parsing operations both return the parsed value and
modify the passed buffer. This precludes their use in places like the cache
code so split out the in place modification into a new parse_inplace()
operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's more idiomatic to pass the map structure around and this means we
can use other bits of information from the map.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we're updating a value in place it's more work to read the value and
compare the value with what we're about to set than it is to just write
the value into the cache; there are no further operations after writing
in the code even though there's an early return here.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Trace when we start and complete async writes, and when we start and
finish blocking for their completion. This is useful for performance
analysis of the resulting I/O patterns.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Even in failed case of pm_runtime_get_sync, the usage_count
is incremented. In order to keep the usage_count with correct
value and runtime power management to behave correctly, call
pm_runtime_put(_sync) in such case.
Signed-off-by Liu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Li Fei <fei.li@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Callers to dma_buf_mmap expect to fput() the vma struct's vm_file
themselves on failure. Not restoring the struct's data on failure
causes a double-decrement of the vm_file's refcount.
Signed-off-by: John Sheu <sheu@google.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
All drivers which implement this need to have some sort of refcount to
allow concurrent vmap usage. Hence implement this in the dma-buf core.
To protect against concurrent calls we need a lock, which potentially
causes new funny locking inversions. But this shouldn't be a problem
for exporters with statically allocated backing storage, and more
dynamic drivers have decent issues already anyway.
Inspired by some refactoring patches from Aaron Plattner, who
implemented the same idea, but only for drm/prime drivers.
v2: Check in dma_buf_release that no dangling vmaps are left.
Suggested by Aaron Plattner. We might want to do similar checks for
attachments, but that's for another patch. Also fix up ERR_PTR return
for vmap.
v3: Check whether the passed-in vmap address matches with the cached
one for vunmap. Eventually we might want to remove that parameter -
compared to the kmap functions there's no need for the vaddr for
unmapping. Suggested by Chris Wilson.
v4: Fix a brown-paper-bag bug spotted by Aaron Plattner.
Cc: Aaron Plattner <aplattner@nvidia.com>
Reviewed-by: Aaron Plattner <aplattner@nvidia.com>
Tested-by: Aaron Plattner <aplattner@nvidia.com>
Reviewed-by: Rob Clark <rob@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
Sometimes drivers need to execute one-off actions in their error handling
or device teardown paths. An example would be toggling a GPIO line to
reset the controlled device into predefined state.
To allow performing such actions when using managed resources let's allow
adding them to stack/group of devres resources.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
lockdep, but it's a mechanical change.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJRJAcuAAoJENkgDmzRrbjxsw0P/3eXb+LddYnx0V0uHYdKpCUf
4vdW7X0fX3Z+aUK69IWRL/6ahoO4TpaHYGHBDjEoivyQ0GDq14X7JNWsYYt3LdMf
3wmDgRc2cn/mZOJbFeVpNV8ox5l/xc0CUvV+iQ8tMjfQItXMXgWUFZKMECsXKSO6
eex3lrw9M2jAX2uL8LQPp9W8xtKu24nSZRC6tH5riE/8fCzi1cZPPAqfxP5c8Lee
ZXtbCRSyAFENZLpKyMe1PC7HvtJyi5NDn9xwOQiXULZV/VOlvP94DGBLIKCM/6dn
4QvZxpG0P0uOlpCgRAVLyh/z7g4XY4VF/fHopLCmEcqLsvgD+V2LQpQ9zWUalLPC
Z+pUpz2vu0gIddPU1nR8R6oGpEdJ8O12aJle62p/RSXWZGx12qUQ+Tamu0tgKcv1
AsiJfbUGNDYfxgU6sHsoQjl2f68LTVckCU1C1LqEbW/S104EIORtGx30CHM4LRiO
32kDC5TtgYDBKQAIqJ4bL48ZMh+9W3uX40p7xzOI5khHQjvswUKa3jcxupU0C1uv
lx8KXo7pn8WT33QGysWC782wJCgJuzSc2vRn+KQoqoynuHGM6agaEtR59gil3QWO
rQEcxH63BBRDgHlg4FM9IkJwwsnC3PWKL8gbX0uAWXAPMbgapJkuuGZAwt0WDGVK
+GszxsFkCjlW0mK0egTb
=tiSY
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module update from Rusty Russell:
"The sweeping change is to make add_taint() explicitly indicate whether
to disable lockdep, but it's a mechanical change."
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
MODSIGN: Add option to not sign modules during modules_install
MODSIGN: Add -s <signature> option to sign-file
MODSIGN: Specify the hash algorithm on sign-file command line
MODSIGN: Simplify Makefile with a Kconfig helper
module: clean up load_module a little more.
modpost: Ignore ARC specific non-alloc sections
module: constify within_module_*
taint: add explicit flag to show whether lock dep is still OK.
module: printk message when module signature fail taints kernel.
Apply the introduced memalloc_noio_save() and memalloc_noio_restore() to
force memory allocation with no I/O during runtime_resume/runtime_suspend
callback on device with the flag of 'memalloc_noio' set.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Decotigny <david.decotigny@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Jiri Kosina <jiri.kosina@suse.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce the flag memalloc_noio in 'struct dev_pm_info' to help PM core
to teach mm not allocating memory with GFP_KERNEL flag for avoiding
probable deadlock.
As explained in the comment, any GFP_KERNEL allocation inside
runtime_resume() or runtime_suspend() on any one of device in the path
from one block or network device to the root device in the device tree
may cause deadlock, the introduced pm_runtime_set_memalloc_noio() sets
or clears the flag on device in the path recursively.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Jiri Kosina <jiri.kosina@suse.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Decotigny <david.decotigny@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We remove the memory like this:
1. lock memory hotplug
2. offline a memory block
3. unlock memory hotplug
4. repeat 1-3 to offline all memory blocks
5. lock memory hotplug
6. remove memory(TODO)
7. unlock memory hotplug
All memory blocks must be offlined before removing memory. But we don't
hold the lock in the whole operation. So we should check whether all
memory blocks are offlined before step6. Otherwise, kernel maybe
panicked.
Offlining a memory block and removing a memory device can be two
different operations. Users can just offline some memory blocks without
removing the memory device. For this purpose, the kernel has held
lock_memory_hotplug() in __offline_pages(). To reuse the code for
memory hot-remove, we repeat step 1-3 to offline all the memory blocks,
repeatedly lock and unlock memory hotplug, but not hold the memory
hotplug lock in the whole operation.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's the big USB merge for 3.9-rc1
Nothing major, lots of gadget fixes, and of course, xhci stuff.
All of this has been in linux-next for a while, with the exception of
the last 3 patches, which were reverts of patches in the tree that
caused problems, they went in yesterday.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZ/kACgkQMUfUDdst+ylEhwCgyM0JEOgLuW7M8D+oNcitZn51
g7oAniD0IkLG8RCB8plLj+82AvthalCo
=bHSs
-----END PGP SIGNATURE-----
Merge tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB merge for 3.9-rc1
Nothing major, lots of gadget fixes, and of course, xhci stuff.
All of this has been in linux-next for a while, with the exception of
the last 3 patches, which were reverts of patches in the tree that
caused problems, they went in yesterday."
* tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (190 commits)
Revert "USB: EHCI: make ehci-vt8500 a separate driver"
Revert "USB: EHCI: make ehci-orion a separate driver"
Revert "USB: update host controller Kconfig entries"
USB: update host controller Kconfig entries
USB: EHCI: make ehci-orion a separate driver
USB: EHCI: make ehci-vt8500 a separate driver
USB: usb-storage: unusual_devs update for Super TOP SATA bridge
USB: ehci-omap: Fix autoloading of module
USB: ehci-omap: Don't free gpios that we didn't request
USB: option: add Huawei "ACM" devices using protocol = vendor
USB: serial: fix null-pointer dereferences on disconnect
USB: option: add Yota / Megafon M100-1 4g modem
drivers/usb: add missing GENERIC_HARDIRQS dependencies
USB: storage: properly handle the endian issues of idProduct
testusb: remove all mentions of 'usbfs'
usb: gadget: imx_udc: make it depend on BROKEN
usb: omap_control_usb: fix compile warning
ARM: OMAP: USB: Add phy binding information
ARM: OMAP2: MUSB: Specify omap4 has mailbox
ARM: OMAP: devices: create device for usb part of control module
...
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
- Rework of the ACPI namespace scanning code from Rafael J. Wysocki
with contributions from Bjorn Helgaas, Jiang Liu, Mika Westerberg,
Toshi Kani, and Yinghai Lu.
- ACPI power resources handling and ACPI device PM update from
Rafael J. Wysocki.
- ACPICA update to version 20130117 from Bob Moore and Lv Zheng
with contributions from Aaron Lu, Chao Guan, Jesper Juhl, and
Tim Gardner.
- Support for Intel Lynxpoint LPSS from Mika Westerberg.
- cpuidle update from Len Brown including Intel Haswell support, C1
state for intel_idle, removal of global pm_idle.
- cpuidle fixes and cleanups from Daniel Lezcano.
- cpufreq fixes and cleanups from Viresh Kumar and Fabio Baltieri
with contributions from Stratos Karafotis and Rickard Andersson.
- Intel P-states driver for Sandy Bridge processors from
Dirk Brandewie.
- cpufreq driver for Marvell Kirkwood SoCs from Andrew Lunn.
- cpufreq fixes related to ordering issues between acpi-cpufreq and
powernow-k8 from Borislav Petkov and Matthew Garrett.
- cpufreq support for Calxeda Highbank processors from Mark Langsdorf
and Rob Herring.
- cpufreq driver for the Freescale i.MX6Q SoC and cpufreq-cpu0 update
from Shawn Guo.
- cpufreq Exynos fixes and cleanups from Jonghwan Choi, Sachin Kamat,
and Inderpal Singh.
- Support for "lightweight suspend" from Zhang Rui.
- Removal of the deprecated power trace API from Paul Gortmaker.
- Assorted updates from Andreas Fleig, Colin Ian King,
Davidlohr Bueso, Joseph Salisbury, Kees Cook, Li Fei,
Nishanth Menon, ShuoX Liu, Srinivas Pandruvada, Tejun Heo,
Thomas Renninger, and Yasuaki Ishimatsu.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=wijn
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
- Rework of the ACPI namespace scanning code from Rafael J. Wysocki
with contributions from Bjorn Helgaas, Jiang Liu, Mika Westerberg,
Toshi Kani, and Yinghai Lu.
- ACPI power resources handling and ACPI device PM update from Rafael
J Wysocki.
- ACPICA update to version 20130117 from Bob Moore and Lv Zheng with
contributions from Aaron Lu, Chao Guan, Jesper Juhl, and Tim Gardner.
- Support for Intel Lynxpoint LPSS from Mika Westerberg.
- cpuidle update from Len Brown including Intel Haswell support, C1
state for intel_idle, removal of global pm_idle.
- cpuidle fixes and cleanups from Daniel Lezcano.
- cpufreq fixes and cleanups from Viresh Kumar and Fabio Baltieri with
contributions from Stratos Karafotis and Rickard Andersson.
- Intel P-states driver for Sandy Bridge processors from Dirk
Brandewie.
- cpufreq driver for Marvell Kirkwood SoCs from Andrew Lunn.
- cpufreq fixes related to ordering issues between acpi-cpufreq and
powernow-k8 from Borislav Petkov and Matthew Garrett.
- cpufreq support for Calxeda Highbank processors from Mark Langsdorf
and Rob Herring.
- cpufreq driver for the Freescale i.MX6Q SoC and cpufreq-cpu0 update
from Shawn Guo.
- cpufreq Exynos fixes and cleanups from Jonghwan Choi, Sachin Kamat,
and Inderpal Singh.
- Support for "lightweight suspend" from Zhang Rui.
- Removal of the deprecated power trace API from Paul Gortmaker.
- Assorted updates from Andreas Fleig, Colin Ian King, Davidlohr Bueso,
Joseph Salisbury, Kees Cook, Li Fei, Nishanth Menon, ShuoX Liu,
Srinivas Pandruvada, Tejun Heo, Thomas Renninger, and Yasuaki
Ishimatsu.
* tag 'pm+acpi-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (267 commits)
PM idle: remove global declaration of pm_idle
unicore32 idle: delete stray pm_idle comment
openrisc idle: delete pm_idle
mn10300 idle: delete pm_idle
microblaze idle: delete pm_idle
m32r idle: delete pm_idle, and other dead idle code
ia64 idle: delete pm_idle
cris idle: delete idle and pm_idle
ARM64 idle: delete pm_idle
ARM idle: delete pm_idle
blackfin idle: delete pm_idle
sparc idle: rename pm_idle to sparc_idle
sh idle: rename global pm_idle to static sh_idle
x86 idle: rename global pm_idle to static x86_idle
APM idle: register apm_cpu_idle via cpuidle
cpufreq / intel_pstate: Add kernel command line option disable intel_pstate.
cpufreq / intel_pstate: Change to disallow module build
tools/power turbostat: display SMI count by default
intel_idle: export both C1 and C1E
ACPI / hotplug: Fix concurrency issues and memory leaks
...
Seth Jennings
David Jander
Sudeep KarkadaNagesha
Hanjun Guo
Mark Brown
Rafael J. Wysocki
Greg Kroah-Hartman
Ionut Nicu
Philipp Zabel
Viresh Kumar
Lars-Peter Clausen
Shuah Khan
Jingoo Han
David Graham White
Linus Torvalds
Randy Dunlap
Guenter Roeck
Fabio Estevam
Sachin Kamat
Marek Szyprowski
Paul Gortmaker
Alexander Graf
Daniel Mack
Kees Cook
Aneesh Kumar K.V
Maarten Lankhorst
Ming Lei
Sahara
Julius Werner
Mauro Carvalho Chehab
Mark Brown
Linus Walleij
Srinivas Kandagatla
Rob Herring
Bernie Thompson
Thomas Meyer
Nathan Fontenot
Stephen Rothwell
Robert P. J. Day
Libo Chen
Takashi Iwai
Maarten ter Huurne
Toshi Kani
Igor Mammedov
Federico Vaga
dyoung@redhat.com
Dimitris Papastamos
Sumit Semwal
Yasuaki Ishimatsu
Tang Chen
David Rientjes
Andrew Morton
Stephen Warren
Ulf Hansson
Kay Sievers
Nishanth Menon
Stratos Karafotis
Arnd Bergmann
Tejun Heo
Zhang Yanfei
Fabio Porcedda
Dmitry Torokhov
Felipe Balbi
Michal Hocko
Li Fei
John Sheu
Daniel Vetter
Al Viro