Different sdio device IDs are designated to support different intel
wimax silicon sku. The new macro SDIO_DEVICE_ID_IWMC3200_WIMAX_2G5(0x1407)
is added to support iwmc3200 2.5GHz sku. The existing
SDIO_DEVICE_ID_IWMC3200_WIMAX(0x1402) is for iwmc3200 general sku.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Especially with the PM framework, those are quite handy to have in driver
code too.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Normally writes to SDIO function 0 outside the vendor specific CCCR
registers are prohibited.
To support embedded devices that require writes to SDIO function 0 outside
this range (e.g. TI WL127x embedded sdio wifi device),
MMC_QUIRK_LENIENT_FN0 is introduced.
A card quirks field is added to `struct mmc_card' to support non-standard
devices (e.g. embedded sdio devices).
[akpm@linux-foundation.org: code in C, not cpp!]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support to disconnect the pull-up resistor on CD/DAT[3] (pin 1)
of the card. This may be desired on certain setups of boards,
controllers and embedded sdio devices which do not need the card's
pull-up. As a result, card detection is disabled and power is saved.
[akpm@linux-foundation.org: simplify sdio_disable_cd() a bit]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Philip Langdale <philipl@overt.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the standard, the SWITCH command should be followed by a
SEND_STATUS command to check for errors.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the new MMC command SLEEP_AWAKE.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Power can be saved by powering off cards that are not in use. This is
similar to suspend / resume except it is under the control of the driver,
and does not require any power management support. It can only be used
when the driver can monitor whether the card is removed, otherwise it is
unsafe. This is possible because, unlike suspend, the driver still
receives card detect and / or cover switch interrupts.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
eMMC's are not removable, so unsafe resume is OK always.
To permit this a new host capability MMC_CAP_NONREMOVABLE has been added
and suspend / resume updated accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change allows the MMC host to be claimed in situations where the host
may or may not have already been claimed. Also 'mmc_try_claim_host()' is
now exported.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MMC hosts that support power saving can use the 'enable' and 'disable'
methods to exit and enter power saving states. An explanation of their
use is provided in the comments added to include/linux/mmc/host.h.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. add intel's sdio vendor id to sdio_ids.h
2. move iwmc3200 sdio devices' ids to sdio_ids.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sdio: add cards id for sms (Siano Mobile Silicon) MDTV receivers
Add SDIO vendor ID, and multiple device IDs for
various SMS-based MDTV SDIO adapters.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
libertas: add support for Marvell SD8688 chip
Use RxPD->pkt_ptr to locate eth803 header in the packet
received since SD8688/v10 firmware allows a gap between
RxPD and eth803 header.
Set SDIO block size to 256 for CMD53.
The maximum block size for SD8688 WLAN function is set
to 512 in TPLFE_MAX_BLK_SIZE. But using 512 as block size
results upto 2K bytes data (4 blocks) being transferred
and causes buffer overflow in firmware.
Both changes above are backward compatible with earlier
firmware versions for SD8385/SD8686.
The SDIO_DEVICE_IDs for SD8688 chip are added in
include/linux/mmc/sdio_ids.h
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Glue between MMC and regulator stacks ... verified with
some OMAP3 boards using adjustable and configured-as-fixed
regulators on several MMC controllers.
These calls are intended to be used by MMC host adapters
using at least one regulator per host. Examples include
slots with regulators supporting multiple voltages and
ones using multiple voltage rails (e.g. DAT4..DAT7 using a
separate supply, or a split rail chip like certain SDIO
WLAN or eMMC solutions).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This function sets the OCR mask bits according to provided voltage
ranges. Will be used by the mmc_spi OpenFirmware bindings.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
In include/linux/mmc/host.h, it is mentionned that the callback to
know if a card is present or not is get_ro(). But it's get_cd().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
For each card successfully added to the bus, create a subdirectory under
the host's debugfs root with information about the card.
At the moment, only a single file is added to the card directory for
all cards: "state". It reflects the "state" field in struct mmc_card,
indicating whether the card is present, readonly, etc.
For MMC and SD cards (not SDIO), another file is added: "status".
Reading this file will ask the card about its current status and
return it. This can be useful if the card just refuses to respond to
any commands, which might indicate that the card state is not what the
MMC core thinks it is (due to a missing stop command, for example.)
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
When CONFIG_DEBUG_FS is set, create a few files under /sys/kernel/debug
containing information about an mmc host's internal state. Currently,
just a single file is created, "ios", which contains information about
the current operating parameters for the bus (clock speed, bus width,
etc.)
Host drivers can add additional files and directories under the host's
root directory by passing the debugfs_root field in struct mmc_host as
the 'parent' parameter to debugfs_create_*.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This adds reading and using of enable_timeout from the CIS
Signed-off-by: Benzi Zbit <benzi.zbit@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Relax requirements on host controllers and only require that they do not
report a transfer count than is larger than the actual one (i.e. a lower
value is okay). This is how many other parts of the kernel behaves so
upper layers should already be prepared to handle that scenario. This
gives us a performance boost on MMC cards.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch fixes sdio_io sparse errors.
This fix changes signature of API functions,
changing
unsigned char -> u8
unsigned short -> u16
unsigned long -> u32 - this was probably a bug in 64 bit platforms
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
There are a lot of crappy controllers out there that cannot handle
all the request sizes that the MMC/SD/SDIO specifications require.
In case the card driver can pad the data to overcome the problems,
this commit adds a helper that calculates how much that padding
should be.
A corresponding helper is also added for SDIO, but it can also deal
with all the complexities of splitting up a large transfer efficiently.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Now get_ro() callback must return 0/1 values for its logical states, and
negative errno values in case of error. If particular host instance doesn't
support RO/WP switch, it should return -ENOSYS.
This patch changes some hosts in two ways:
1. Now functions should be smart to not return negative values in
"RO asserted" case (particularly gpio_ calls could return negative
values for the outermost GPIOs).
Also, board code usually passes get_ro() callbacks that directly return
gpioreg & bit result, so at91_mci, imxmmc, pxamci and mmc_spi's get_ro()
handlers need take special care when returning platform's values to the
mmc core.
2. In case of host instance didn't implement get_ro() callback, it should
really return -ENOSYS and let the mmc core decide what to do about it
(mmc core thinks the same way as the hosts, so it isn't functional
change).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some hosts (and boards that use mmc_spi) do not use interrupts on the CD
line, so they can't trigger mmc_detect_change. We want to poll the card
and see if there was a change. 1 second poll interval seems resonable.
This patch also implements .get_cd() host operation, that could be used
by the hosts that are able to report card-detect status without need to
talk MMC.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch removes a CVS tag that wasn't updated for a long time.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This field and corresponding defines are simply never used anywhere
in the code. But its mere presence is enough to confuse some host
driver authors who attempt to rely on it. Let's eliminate the
possibility for confusion and remove it entirely.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add a led trigger for each host controller that indicates if there
is a request active on the controller.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Teach the MMC/SD/SDIO system headers that some hosts use SPI mode
- New host capabilities and status bits
* MMC_CAP_SPI, with mmc_host_is_spi() test
* mmc_host.use_spi_crc flag
- SPI-specific declarations:
* Response types, MMC_RSP_SPI_R*
* Two SPI-only commands
* Status bits used native to SPI: R1_SPI_*, R2_SPI_*
- Fix a few (unrelated) whitespace bugs in the headers.
- Reorder a few mmc_host fields, removing several bytes of padding
None of these changes affect current code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add sdio_f0_readb() and sdio_f0_writeb() functions to reading and
writing function 0 registers. Writes outside the vendor specific CCCR
registers (0xF0 - 0xFF) are not permitted.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Before a driver is probed, set the function's block size to the default so the
driver is sure the block size is something sensible and it needn't explicitly
set it.
The default block size is the largest that's supported by both the card and
the host, with a maximum of 512 to ensure aribitrarily sized transfer use the
optimal (least) number of commands.
See http://lkml.org/lkml/2007/8/7/150 for reasons for the block size choice.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Support the multi-byte transfer operation, including handlers for
common operations like writel()/readl().
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
It is sometimes necessary to give up on trying to claim the host lock,
especially if that happens in a thread that has to be stopped.
While at it, fix the description for mmc_claim_host() which was wrong.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add a more clean separation between global, common CIS information
and the function specific one as we need the common information in
places where no specific function is specified.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This way those tuples that the core cares about are consumed by the core
code, and tuples that only function drivers might make sense of are
available to drivers.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Like many other buses, the devices (functions) on the SDIO bus
must be enabled before they can be used. Add functions that allow
drivers to do so.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
David S. Miller
Cindy H Kao
Alexey Dobriyan
Nicolas Pitre
Ohad Ben-Cohen
Adrian Hunter
Jarkko Lavinen
Tomas Winkler
Uri Shkolnik
Bing Zhao
David Brownell
Anton Vorontsov
Kay Sievers
Thomas Petazzoni
Haavard Skinnemoen
Linus Torvalds
Benzi Zbit
Pierre Ossman
Adrian Bunk
Nicolas Pitre
David Brownell
David Vrabel