Device tree source file for the PPC405 Walnut evaluation board.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Commit 804ace8881 changed the behavior of how compatible nodes are found.
This highlighted a bug on the Bamboo board where it wasn't probing the bus
specified in the DTS file. We fix it by being explicit about which bus to
probe.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbvear.id.au>
The patch below removes the dtc incantation instructions from the
in-kernel DTS files. It's not needed, and is prone to being
out-of-date most of the time.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
The names of STI and CLI macros were derived from i386 arch historically,
but their name are incomprehensible.
So, for easy to understand, rename these macros to ENABLE_INTERRUPTS
and DISABLE_INTERRUPTS, respectively.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Apparently XEN does not keep the contents of the 48-bit gdt_48 data
structure that is passed to lgdt in the XEN machine state. Instead it
appears to save the _address_ of the 48-bit descriptor
somewhere. Unfortunately this data happens to reside on the stack and
is probably no longer availiable at the time of the actual protected
mode jump.
This is Xen bug but given that there is a one-line patch to work
around this problem, the linux kernel should probably do this. My fix
is to make the gdt_48 description in setup_gdt static (in setup_idt
this is already the case). This allows the kernel to boot under
Xen HVM again.
Signed-off-by: Christian Ehrhardt <lk@c--e.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
- Separate sys_call_table from arch/m32r/kernel/entry.S and
move it to arch/m32r/kernel/system_call.S.
- Change sys_call_table section from .data to .rodata.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
If no IRQ request is found in the IRQ check of ei_handler,
we can exit directly by jumping "restore_all", instead of via
"ret_from_intr".
This modification is also likely effective for IPI operations,
because scheduler call never happen at the exit of IPIs.
Signed-off-by: Hitoshi Yamamoto <hitoshiy@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Simplify and clean up messy ei_handler code in arch/m32r/kernel/entry.S.
- Remove ifdef's for CONFIG_CHIP_* configulations.
- Rearrange the M32700 workaround code.
- Remove the messy platform-dependent interrupt check routines and
consolidate them to common INT0/INT1/INT2 check routines for all
platforms with cascaded interrupt controllers.
Signed-off-by: Hitoshi Yamamoto <hitoshiy@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
On some m32r platforms, cascaded ICUs are used.
This patch is required to simplify ei_handler and consolidate platform-
dependent ICU check routines.
platform ICU/INT1 ICU/INT0 ICU/INT2
-------------- -------- -------- --------
m32104ut o - -
m32700ut o o o
opsput o o o
usrv o - -
(others) - - -
Signed-off-by: Hitoshi Yamamoto <hitoshiy@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
After my last patch we have a new header file for HP simulator use.
Here's code to use it for stuff that used to have `extern' statements
inline in the code. Functionality should not change with this patch.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch cleans up the `enable early console for SKI' patch
(471e7a4484), and
1. potentially allows the gensparse_defconfig to work again.
(there are other problems running a generic kernel on Ski)
2. fixes the `console registered twice' problem.
3. Cleans up the code by moving the `extern hpsim_cons' declaration to
a new asm/hpsim.h file.
Thanks to Jes for comments.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When dumping memory via sysrq-m it is possible to take a bogus NMI watchdog
or softlockup watchdog because the dump can take a long time on big memory
systems.
Occasionally tickle the watchdog when doing the dump.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add additional support for CPU disable on SN platforms.
Correctly setup the smp_affinity mask for I/O error IRQs.
Restrict the use of the feature to Altix 4000 and 450 systems
running with a CPU disable capable PROM, and do not allow disabling
of CPU 0.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
vmalloc() returns a void pointer - no need to cast it.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
lguest didn't initialize the kernel stack the way a real i386 kernel
does, and ended up triggering a corner-case in the stack frame checking
that doesn't happen on naive i386, and that the stack dumping didn't
handle quite right.
This makes the frame handling more correct, and tries to clarify the
code at the same time so that it's a bit more obvious what is going on.
Thanks to Rusty Russell for debugging the lguest failure-
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The VESA BIOS is specified to be register-clean. However, we have now
found at least one system which violates that. Thus, be as paranoid
about VESA calls as about everything else.
Huge thanks to Will Simoneau for reporting, diagnosing, and testing
this out on Dell Inspiron 5150.
Cc: Will Simoneau <simoneau@ele.uri.edu>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
For hugepage mappings, the file offset, like the address and size, needs to
be aligned to the size of a hugepage.
In commit 68589bc353, the check for this was
moved into prepare_hugepage_range() along with the address and size checks.
But since BenH's rework of the get_unmapped_area() paths leading up to
commit 4b1d89290b, prepare_hugepage_range()
is only called for MAP_FIXED mappings, not for other mappings. This means
we're no longer ever checking for an aligned offset - I've confirmed that
mmap() will (apparently) succeed with a misaligned offset on both powerpc
and i386 at least.
This patch restores the check, removing it from prepare_hugepage_range()
and putting it back into hugetlbfs_file_mmap(). I'm putting it there,
rather than in the get_unmapped_area() path so it only needs to go in one
place, than separately in the half-dozen or so arch-specific
implementations of hugetlb_get_unmapped_area().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Adam Litke <agl@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dependencies of CONFIG_SUSPEND and CONFIG_HIBERNATION introduced by commit
296699de6b "Introduce CONFIG_SUSPEND for
suspend-to-Ram and standby" are incorrect, as they don't cover the facts that
(1) not all architectures support suspend and (2) SMP hibernation is only
possible on X86 and PPC64 (if CONFIG_PPC64_SWSUSP is set).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct the name of the spi_txx9 driver (and their in-tree user)
instead of MODULE_ALIAS workaround. This would be preferable in the
long term.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stop UML crashing when trying to dump a process core on x86_64. This is the
minimal fix to stop the crash - more things are broken here, and patches are
forthcoming.
The immediate thing to do is define ELF_CORE_COPY_REGS and
ELF_CORE_COPY_FPREGS. Defining ELF_CORE_COPY_FPREGS allows dump_fpu to go
away. It is defined in terms of save_fp_registers, so that needs to be added.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a class of bugs in the UML linker scripts which caused section boundary
variables to sometimes not line up with their sections.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1) sun4{u,v}_build_msi() have improper return value handling.
We should always return negative error codes, instead of
using the magic value "0" which could in fact be a valid
MSI number.
2) sun4{u,v}_build_msi() should return -ENOMEM instead of
calling prom_prom() halt with kzalloc() of the interrupt
data fails.
3) We 'remembered' the MSI number using a singleton in the
struct device archdata area, this doesn't work for MSI-X
which can cause multiple MSIs assosciated with one device.
Delete that archdata member, and instead store the MSI
number in the IRQ chip data area.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes we were using 32-bit values and the top bits were
getting inadvertantly chopped off. This will matter for the
forthcoming Fire controller MSI support.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] PS3: Fix bug where the major version part is not compared
[POWERPC] Update defconfigs
[POWERPC] spufs: Don't call spu_run_init from spu_reacquire_runnable
[POWERPC] spufs: Fix update of mailbox status register during backed wbox write
[POWERPC] spu_manage: fix spu_unit_number for celleb device tree
[POWERPC] Update defconfigs
[POWERPC] Flush registers to proper task context
Another fallout from the removal of #include <linux/fs.h> from mm.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the bug that the major version part of the firmware version number
is ignored in the comparison done by ps3_compare_firmware_version
because the difference of two 64-bit quantities is returned as an int.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During GPIO testing on PiMX1 board there has been revealed
problem with some pins input functions. The GIUS bit has
to be set for inputs to work reliably too. It is surprising
that input worked on some inputs with incorrect setup before.
DR is not mandatory, but it ensures stable constant level
on internal traces.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a major bug which was happening when a SPU thread advances
its execution right after being restored to a SPU. A potentially
outdated NPC value was being (re)written to the SPU.
So, spu_run_init, in this case, was either not doing anything relevant,
or breaking the execution of the SPU thread.
This fixes a common problem of losing a mailbox write when it was done
to a saved context.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When a process writes into the inbound spu mailbox (wbox) while the
context is saved, we accidentally break the contents of the mb_stat_R
register by clearing other entries of the mailbox status register. This
can cause the user side to hang.
This change fixes the problem by only altering the appropriate bits
of the mailbox status register during a backing-store write.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a regression introduced with 2.6.23-rc4 after on some
confusion about the device tree interfaces.
IBM QS21 device trees provide "physical-id", so we changed the code to
run on that and remain compatible with all IBM machines.
However, the Toshiba Celleb device tree provides the "unit-id" property,
which was in the Linux code, but never used in this way on IBM hardware.
Legacy device tree used the reg property for the physical id of an spe.
This patch fixes find_spu_unit_number to look for the spu id in that order.
The length is checked to avoid misinterpretation in case the attributes
unit-id or reg do not contain the id.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
When we flush register state for FP, Altivec, or SPE in flush_*_to_thread
we need to respect the task_struct that the caller has passed to us.
Most cases we are called with current, however sometimes (ptrace) we may
be passed a different task_struct.
This showed up when using gdbserver debugging a simple program that used
floating point. When gdb tried to show the FP regs they all showed up as
0, because the child's FP registers were never properly flushed to memory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The pending interrupts can be remaining at boot up time on some
platform. This will cause spurious interrupts when interrupt is
enabled for the first time. This patch clears IVR at the CPU
initialization to eliminate such spurious interrupts.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix handling for spurious interrupts not being mapped to any IRQs.
Currently, spurious interrupts that are not mapped to any IRQs are
handled as IRQ 15 (== IA64_SPURIOUS_VECTOR). But it is not proper
because vector != irq. We need special handlings for such spurious
interrupts not being mapped to any IRQs.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
As pointed out by Jrgen, we are overflowing the number of GPIOs
in pxa_init_irq_gpio(). I'm seeing the same problem on my HTC
Universal PXA270 based PDA.
According to Eric, the function argument is the number of GPIOs,
so we should keep the semantics and reduce the number of
iteration by 1.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Jrgen Schindele <linux@schindele.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC32]: Make flush_tlb_kernel_range() an inline function.
[SERIAL]: Fix 32-bit warnings in sunzilog.c and sunsu.c
[SPARC32]: Kill unused vars and macros from prom/console.c
[SPARC32]: Add __cmpdi2() libcall implementation ala. MIPS.
[VIDEO]: Do not prom_halt() in cg3 and bw2 device probe.
[SUNVDC]: Use slice 0xff on VD_DISK_TYPE_DISK.
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix SLB initialization at boot time
[POWERPC] Fix undefined reference to device_power_up/resume
[POWERPC] cell: Update cell_defconfig for 2.6.23
[POWERPC] axonram: Do not delete gendisks queue in error path
[POWERPC] axonram: Module modification for latest firmware API changes
[POWERPC] cell: Support pinhole-reset on IBM cell blades
[POWERPC] spu_manage: Use newer physical-id attribute
[POWERPC] pasemi: Another IOMMU bugfix for 64K PAGE_SIZE
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
[PARISC] Add NOTES section
[PARISC] Use compat_sys_getdents
[PARISC] Do not allow STI_CONSOLE to be modular
[PARISC] Clean up sti_flush
[PARISC] Add dummy isa_(bus|virt)_to_(virt|bus) inlines
[PARISC] Add empty <asm-parisc/vga.h>
Bisected bizarre kernel-space nullptr dereference in udev to commit
18991197b4, adding the NOTES section fixes
it.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
shutdown_bridge_irq disconnects the irq so we need to connect the irq or
requesting the same irq a send time will fail. This used to make
things like ifconfig eth0 down; ifconfig eth0 up fail on IP27.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Certain 32-bit kernel configurations seem to be able to cause references,
this was observed with gcc 4.1.2.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 96bde06a2d several callers of
pcibios_resource_to_bus are no longer marked __devinit resulting in a
pile of modpost warnings if PCI && !HOTPLUG:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x15dde8): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_map_rom' and 'pci_map_rom_copy')
WARNING: vmlinux.o(.text+0x15e140): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_update_resource' and 'pci_claim_resource')
WARNING: vmlinux.o(.text+0x15f0cc): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f0f0): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f114): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f138): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f438): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'pbus_size_mem')
WARNING: vmlinux.o(.text+0x15f4f4): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'pbus_size_mem')
Removing __devinit from pcibios_resource_to_bus make the same necessary
for pcibios_fixup_device_resources as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 96bde06a2d pcibios_fixup_bus's caller
pci_scan_child_bus is no longer marked __devinit resulting in this modpost
warning if PCI && !HOTPLUG:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x158b9c): Section mismatch: reference to .init.text:pcibios_fixup_bus (between 'pci_scan_child_bus' and 'pci_scan_bus_parented')
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The appended patch adds code to update siginfo_t's si_code field. It
fixes e.g. a floating point overflow regression in the SBCL testsuite.
Signed-off-By: Thiemo Seufer <ths@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Also removes the while(1); loop by propagating the ATTRIB_NORET of die()
to nmi_exception_handler.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The rtc-rs5c348 SPI driver name doesn't match its module name, which
prevents it from properly hotplugging. There is only one in-tree user
of its driver, which is fixed by this patch too.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/basler/excite/excite_prom.o
arch/mips/basler/excite/excite_prom.c:136:3: #error 64 bit support not implemented
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS doesn't do CPU hotplugging yet but since many of the functions don't
even have an __init let's fix this right.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Leaving these sections is useful to some tools that look at the image, and
none of them are loaded into memory. The .mdebug.abi64 section, in
particular, lets GDB recognize vmlinux.32 as an N64 program instead of
guessing that it is O32.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add generic irq_chip for TX39/TX49 SoCs. This can be replace
jmr3927_irq_irc, tx4927_irq_pic_type and tx4938_irq_pic_type.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is needed since the Sibyte serial driver was exchanged.
Issue report by Imre Kaloz <kaloz@openwrt.org>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (30 commits)
ACPI: work around duplicate name "VID" problem on T61
acpiphp_ibm: add missing '\n' to error message
ACPI: add dump_stack() to trace acpi_format_exception programming errors
make drivers/acpi/scan.c:create_modalias() static
ACPI: Fix a warning of discarding qualifiers from pointer target type
ACPI: "ACPI handle has no context!" should be KERN_DEBUG
ACPI video hotkey: export missing ACPI video hotkey events via input layer
ACPI: Validate XSDT, use RSDT if XSDT fails
ACPI: /proc/acpi/thermal_zone trip points are now read-only, mark them as such
ACPI: fix ia64 allnoconfig build
PNP: remove null pointer checks
PNP: remove MODULE infrastructure
ISAPNP: removed unused isapnp_detected and ISAPNP_DEBUG
PNPACPI: remove unnecessary casts of "void *"
PNPACPI: simplify irq_flags()
PNP: fix up after Lindent
ACPI: enable GPEs before calling _WAK on resume
asus-laptop: Fix rmmod of asus_laptop
sony-laptop: call sonypi_compat_init earlier
sony-laptop: enable Vaio FZ events
...
This partially reverts edd0622bd2.
It turns out that the part of that commit that aimed to ensure that we
created an SLB entry for the kernel stack on secondary CPUs when
starting the CPU didn't achieve its aim, and in fact caused a
regression, because get_paca()->kstack is not initialized at the point
where slb_initialize is called.
This therefore just reverts that part of that commit, while keeping
the change to slb_flush_and_rebolt, which is correct and necessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
On exit do not delete gendisk's queue because this is already done by
del_gendisk(). Doing it twice may cause memory damage.
Signed-off-by: Maximilian <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Firmware would not deliver two interrupt numbers in device-tree any more
but only one, for correctable ECC, because uncorrectable ECC from now
is handled by firmware itself.
Changes in the axonram module are necessary because in the old version, if
it is not allowed to fetch the second interrupt number from device-tree,
it interpretes this as an error case and exits.
Signed-off-by: Maximilian <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Cell Broadband Engine has a method of injecting a
system-reset-exception from an external source into the
operating system, which should trigger the regular behaviour
of entering xmon or kdump.
Unfortunately, the exception handler cannot distinguish it from
other interrupt causes by the SRR1 register, which gets used
for this on Power 6 and others.
IBM Blade servers that want to support triggering the
system reset exception using a pinhole button in the front
panel therefore use an extra register to determine the
reset cause.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
--
Signed-off-by: Paul Mackerras <paulus@samba.org>
Legacy device tree used the reg property for the physical id of an
spe. On newer device tree layouts the reg property contains the
"correct" value in the reg attribute. So there has been intoduced the
"physical-id" on newer devicetree layouts. The id is stored by
spu_manage into the spu struct as spe_id. cbe_thermal has been
changed to use the spu->spe_id. There's no need for the thermal code
to check devicetree attributes for itself.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
More fallout from the switch from PAGE_SIZE based IOMMU to the native page
size for the driver. By pure luck it happened to work most of the time, since
we end up invalidating the wrong entries in the TLB.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
[x86 setup] Make sure AH=00h when setting a video mode
[x86 setup] Volatilize asm() statements
Include linux/fs.h to get the prototype for do_pipe().
Build fix.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include linux/fs.h to get the prototype for getname().
Build fix.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Passing a u8 into a register doesn't mean gcc will zero-extend it.
Also, don't depend on thhe register not to change.
Per bug report from Saul Tamari.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
asm() statements need to be volatile when:
a. They have side effects (other than value returned).
b. When the value returned can vary over time.
c. When they have ordering constraints that cannot be expressed to gcc.
In particular, the keyboard and timer reads were violating constraint (b),
which resulted in the keyboard/timeout poll getting
loop-invariant-removed when compiling with gcc 4.2.0.
Thanks to an anonymous bug reporter for pointing this out.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
construct a more or less wall-clock time out of sched_clock(), by
using ACPI-idle's existing knowledge about how much time we spent
idling. This allows the rq clock to work around TSC-stops-in-C2,
TSC-gets-corrupted-in-C3 type of problems.
( Besides the scheduler's statistics this also benefits blktrace and
printk-timestamps as well. )
Furthermore, the precise before-C2/C3-sleep and after-C2/C3-wakeup
callbacks allow the scheduler to get out the most of the period where
the CPU has a reliable TSC. This results in slightly more precise
task statistics.
the ACPI bits were acked by Len.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Len Brown <len.brown@intel.com>
The pins for GPIO should be provided as plain number
build as (GPIO_PORTx + pin_number). But to setup
the output GPIO_GIUS and GPIO_DR have to be specified
in mode to route right value to the pin.
This is a fix, it should go to 2.6.23
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We no longer have any dependancies on include/asm-ppc so we can get ride
of the makefile hacks to include it in the build process.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To build arch/powerpc without including asm-ppc/ we need these files
in asm-powerpc/
Moved some headers under arch/powerpc/platforms if they were only used by
platform or driver files and fixed up the source file includes to match
the new locations
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove includes of files that existed in arch/ppc that we dont need in
arch/powerpc anymore. The following includes were removed:
<asm/amigappc.h>
<asm/bootinfo.h>
<asm/ppcboot.h>
<asm/ppc_sys.h>
<asm/residual.h>
<asm/m8260_pci.h>
This also caused platforms/embedded6xx/mpc7448_hpc2.h to no longer be
needed and thus removed.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Xen i386 xen-head.S fix sections mixup
xen-head.S does not come back to the data section, leaving the text section
as current section. It causes problems with a slightly enhanced DEBUG_RODATA
that supports CONFIG_HOTPLUG and bringing a CPU up after the text has been
marked read-only: reference to early_gdt_descr causes a page fault.
Updates:
- It should be using pushsection/popsection.
- Actually, the push/popsections around the ELFNOTEs are redundant; ELFNOTE()
does its own push/popsection to put things into the appropriate .note* section
anyway.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous patch which limited the number of sectors in a single request
to a COWed device was correct in concept, but the limit was implemented in
the wrong place.
By putting it in ubd_add, it covered the cases where the COWing was
specified on the command line. However, when the command line only has the
COW file specified, the fact that it's a COW file isn't known until it's
opened, so the limit is missed in these cases.
This patch moves the sector limit from ubd_add to ubd_open_dev.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't include RODATA into text segment as it includes the kallsyms data and
can cause spurious link failures (layout differences can change the number of
symbols in kallsyms, i.e. when a symbol is equal to _etext it's not
included).
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC32]: Revert f642b26380.
[SPARC64]: Need to clobber global reg vars in switch_to().
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Change atomic_read/set to inline functions with barrier semantics.
[S390] kprobes: fix instruction length calculation
[S390] hypfs: inode corruption due to missing locking
[S390] disassembler: fix b2 opcodes like srst, bsg, and others
[S390] vmur: fix reference counting for vmur device structure
[S390] vmur: fix diag14 exceptions with addresses > 2GB.
[S390] qdio: Refresh buffer states for IQDIO Asynchronous output queue
[S390] qdio: fix EQBS handling on CCQ96
[S390] cio: change confusing message in cmf.
[S390] cio: dont forget to set last slot to NULL in ccw_uevent().
Touching vmalloc memory in the middle of a lazy mode update can generate
a kernel PDE update, which must be flushed immediately. The fix is to
leave lazy mode when doing a vmalloc sync.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Placing a kprobe on "bc" instruction (s390/s390x) can cause an oops.
The instruction length is encoded into the first two bits of the s390
instruction. Kprobe is incorrectly computing the instruction length.
The instruction length is used for determining what type of "fix-up" is
needed for conditional branch instruction. The problem can bee seen by
placing a kprobe on a "bc" instruction that will not branch. The
results is that Kprobe incorrectly computes the new instruction
pointer (psw.addr) after single stepping the instruction. The problem
is corrected with this patch.
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
hypfs removes the whole hypfs directory tree and creates a new one, when a
process triggers an update by writing to the "update" attribute. When removing
and creating files, it is necessary to lock the inode of the parent directory
where the files live. Currently hypfs does not lock the parent inode, which
can lead to inode corruption. This patch:
* Introduces correct locking
* Fixes i_nlink reference counting for inodes, when creating directories
* Adds info printk, when hypfs filesystem has been mounted
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The instruction table for b2 opcodes was missing an opfrag value
for the cpya instruction. All instructions specified after cpya
were not considered by the disassembler. The fix is simple and
obvious - add the opfrag field to the cpya instruction.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
There are several s390 diagnose calls, which must be executed below the
2GB memory boundary. In order to enforce this, those diagnoses must be
compiled into the kernel. Currently diag 14 can be called within the
vmur kernel module from addresses above 2GB. This leads to specification
exceptions. This patch moves diag10, diag14 and diag210 into the new
diag.c file.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The APLLs are most efficiently idled by hardware.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Bugfixes for the OSK led support:
- Fix Kconfig merge glitches: Mistral handles idle and timer leds just fine
- Fix pm_suspend() runtime botch: can't sleep, so can't touch tps65010 leds
Improvements:
- Switch sense of Mistral idle led, so idle == off
Probably the TPS65010 leds should be handled only by the "new led" API.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the OMAP1 version of omap_dm_timer_get_fclk(), and its associated
compile-time warning. It would only BUG() if called, while it's only
called on OMAP2.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Josh Boyer
Valentine Barshak
Hirokazu Takata
Christian Ehrhardt
Linus Torvalds
Peter Chubb
Peter Chubb
Prarit Bhargava
John Keller
Jesper Juhl
Linus Torvalds
H. Peter Anvin
David Gibson
Rafael J. Wysocki
Atsushi Nemoto
Jeff Dike
David S. Miller
Adrian Bunk
Masakazu Mokuno
Pavel Pisa
Paul Mackerras
Andre Detsch
Arnd Bergmann
Christian Krafft
Kumar Gala
Kenji Kaneshige
Samuel
Kyle McMartin
Ralf Baechle
Thiemo Seufer
Nicolas Schichan
Ilpo Järvinen
Yoichi Yuasa
Ralf Baechle
Daniel Jacobowitz
Russell King
Arnd Bergmann
Maxim Shchetynin
Olof Johansson
Len Brown
Greg Ungerer
Ingo Molnar
Mathieu Desnoyers
Roman Zippel
Geert Uytterhoeven
Yoshinori Sato
Zachary Amsden
David Wilder
Michael Holzheu
Christian Borntraeger
Juha Yrjola
Dirk Behme
David Brownell