tag_lan9303.c does check for a NULL dst but that's already checked by
dsa_switch_rcv() one layer above.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
To define the outgoing port and to discover the incoming port a regular
VLAN tag is used by the LAN9303. But its VID meaning is 'special'.
This tag handler/filter depends on some hardware features which must be
enabled in the device to provide and make use of this special VLAN tag
to control the destination and the source of an ethernet packet.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves as is the legacy DSA code from dsa.c to legacy.c,
except the few shared symbols which remain in dsa.c.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All DSA tag receive functions do strictly the same thing after they have located
the originating source port from their tag specific protocol:
- push ETH_HLEN bytes
- set pkt_type to PACKET_HOST
- call eth_type_trans()
- bump up counters
- call netif_receive_skb()
Factor all of that into dsa_switch_rcv(). This also makes us return a pointer to
a sk_buff, which makes us symetric with the xmit function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All DSA tag receive functions need to unshare the skb before mangling it, move
this to the generic dsa_switch_rcv() function which will allow us to make the
tag receive function return their mangled skb without caring about freeing a
NULL skb.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_switch_rcv() already tests for dst == NULL, so there is no need to duplicate
the same check within the tag receive functions.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the support for the 4-bytes tag for DSA port distinguishing inserted
allowing receiving and transmitting the packet via the particular port.
The tag is being added after the source MAC address in the ethernet
header.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 96567d5dac ("net: dsa: dsa2: Add basic support of devlink")
I see the following link error with CONFIG_NET_DSA=y and CONFIG_NET_DEVLINK=m:
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe226b): undefined reference to `devlink_alloc'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe2284): undefined reference to `devlink_register'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe243e): undefined reference to `devlink_port_register'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe24e1): undefined reference to `devlink_port_register'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe24fa): undefined reference to `devlink_port_type_eth_set'
net/built-in.o: In function 'dsa_dst_unapply.part.8':
dsa2.c:(.text.unlikely+0x345): undefined reference to 'devlink_port_unregister'
dsa2.c:(.text.unlikely+0x36c): undefined reference to 'devlink_port_unregister'
dsa2.c:(.text.unlikely+0x38e): undefined reference to 'devlink_port_unregister'
dsa2.c:(.text.unlikely+0x3f2): undefined reference to 'devlink_unregister'
dsa2.c:(.text.unlikely+0x3fb): undefined reference to 'devlink_free'
Fix this by adding a dependency on MAY_USE_DEVLINK so that CONFIG_NET_DSA
get switched to be build as module when CONFIG_NET_DEVLINK=m.
Fixes: 96567d5dac ("net: dsa: dsa2: Add basic support of devlink")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce crosschip_bridge_{join,leave} operations in the dsa_switch_ops
structure, which can be used by switches supporting interconnection.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register the switch and its ports with devlink.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.
Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.
No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I do not hold the copyright of the DSA core and drivers source files,
since these changes have been written as an initiative of my day job.
Fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a DSA switch driver cannot program an ageing time value due to it
being out-of-range, switchdev will raise a stack trace before failing.
To fix this, add ageing_time_min and ageing_time_max members to the
dsa_switch in order for the switch drivers to optionally specify their
supported ageing time limits.
The DSA core will now check for provided ageing time limits and return
-ERANGE from the switchdev prepare phase if the value is out-of-range.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ageing time is defined as unsigned int, so make
dsa_fastest_ageing_time return an unsigned int instead of int.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding switch.o to the list of DSA object files, we essentially
duplicated the previous obj-y line and just added switch.o, remove the
duplicate.
Fixes: f515f192ab ("net: dsa: add switch notifier")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_slave_create() can fail, and dsa_user_port_unapply() will properly check
for the network device not being NULL before attempting to destroy it. We were
not setting the slave network device as NULL if dsa_slave_create() failed, so
we would later on be calling dsa_slave_destroy() on a now free'd and
unitialized network device, causing crashes in dsa_slave_destroy().
Fixes: 83c0afaec7 ("net: dsa: Add new binding implementation")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as of
811a919135 ("phy state machine: failsafe leave invalid RUNNING state")
Reported-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow drivers to use the new DSA API with platform data. Most of the
code in net/dsa/dsa2.c does not rely so much on device_nodes and can get
the same information from platform_data instead.
We purposely do not support distributed configurations with platform
data, so drivers should be providing a pointer to a 'struct
dsa_chip_data' structure if they wish to communicate per-port layout.
Multiple CPUs port could potentially be supported and dsa_chip_data is
extended to receive up to one reference to an upstream network device
per port described by a dsa_chip_data structure.
dsa_dev_to_net_device() increments the network device's reference count,
so we intentionally call dev_put() to be consistent with the DT-enabled
path, until we have a generic notifier based solution.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for using this function in net/dsa/dsa2.c, rename the function
to make its scope DSA specific, and export it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A slave device will now notify the switch fabric once its port is
bridged or unbridged, instead of calling directly its switch operations.
This code allows propagating cross-chip bridging events in the fabric.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a notifier block per DSA switch, registered against a notifier head
in the switch fabric they belong to.
This infrastructure will allow to propagate fabric-wide events such as
port bridging, VLAN configuration, etc. If a DSA switch driver cares
about cross-chip configuration, such events can be caught.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scope of the functions inside net/dsa/slave.c must be the slave
net_device pointer. Change to state setter helper accordingly to
simplify callers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an error is returned during the bridging of a port in a
NETDEV_CHANGEUPPER event, net/core/dev.c rolls back the operation.
Be consistent and unassign dp->bridge_dev when this happens.
In the meantime, add comments to document this behavior.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code handling the slave netdevice notifier call by
providing a dsa_slave_changeupper helper for NETDEV_CHANGEUPPER, and so
on (only this event is supported at the moment.)
Return NOTIFY_DONE when we did not care about an event, and NOTIFY_OK
when we were concerned but no error occurred, as the API suggests.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the netdevice notifier block register code in slave.c and provide
helpers for dsa.c to register and unregister it.
At the same time, check for errors since (un)register_netdevice_notifier
may fail.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add necessary plumbing at the slave network device level to have switch
drivers implement ndo_setup_tc() and most particularly the cls_matchall
classifier. We add support for two switch operations:
port_add_mirror and port_del_mirror() which configure, on a per-port
basis the mirror parameters requested from the cls_matchall classifier.
Code is largely borrowed from the Mellanox Spectrum switch driver.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding support for CFP/TCAMP in the bcm_sf2 driver add the
plumbing to call into driver specific {get,set}_rxnfc operations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon reception of the NETDEV_CHANGEUPPER, a leaving port is already
unbridged, so reflect this by assigning the port's bridge_dev pointer to
NULL before calling the port_bridge_leave DSA driver operation.
Now that the bridge_dev pointer is exposed to the drivers, reflecting
the current state of the DSA switch fabric is necessary for the drivers
to adjust their port based VLANs correctly.
Pass the bridge device pointer to the port_bridge_leave operation so
that drivers have all information to re-program their chips properly,
and do not need to cache it anymore.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bridge_dev pointer from dsa_slave_priv to dsa_port so that DSA
drivers can access this information and remove the need to cache it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store a pointer to the dsa_port structure in the dsa_slave_priv
structure, instead of the switch/port index.
This will allow to store more information such as the bridge device,
needed in DSA drivers for multi-chip configuration.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the physical switch instance and port index a DSA port belongs to to
the dsa_port structure.
That can be used later to retrieve information about a physical port
when configuring a switch fabric, or lighten up struct dsa_slave_priv.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_switch structure contains the number of ports. Use it where the
structure is valid instead of the DSA_MAX_PORTS value.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the ports[DSA_MAX_PORTS] array of the dsa_switch structure for a
zero-length array, allocated at the same time as the dsa_switch
structure itself. A dsa_switch_alloc() helper is provided for that.
This commit brings no functional change yet since we pass DSA_MAX_PORTS
as the number of ports for the moment. Future patches can update the DSA
drivers separately to support dynamic number of ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the assignment of ports in _dsa_register_switch() closer to where
it is checked, no functional change. Re-order declarations to be
preserve the inverted christmas tree style.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it clear that these functions take a device_node structure pointer
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing platform data, and therefore no valid
device_node pointer, make most DSA functions takes a pointer to a
dsa_port structure whenever possible. While at it, introduce a
dsa_port_is_valid() helper function which checks whether port->dn is
NULL or not at the moment.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing dsa_register_switch() to be supplied with
device/platform data, pass down a struct device pointer instead of a
struct device_node.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 448b4482c6 ("net: dsa: Add lockdep class to tx queues to avoid
lockdep splat") removed the netif_device_detach() call done in
dsa_slave_suspend() which is necessary, and paired with a corresponding
netif_device_attach(), bring it back.
Fixes: 448b4482c6 ("net: dsa: Add lockdep class to tx queues to avoid lockdep splat")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We may be able to see invalid Broadcom tags when the hardware and drivers are
misconfigured, or just while exercising the error path. Instead of flooding
the console with messages, flat out drop the packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the wrong !, otherwise we get false positives about having
multiple CPU interfaces.
Fixes: b22de49086 ("net: dsa: store CPU switch structure in the tree")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to check the return value of phy_connect_direct() in
dsa_slave_phy_connect() otherwise we may be continuing the
initialization of a slave network device with a PHY that already
attached somewhere else and which will soon be in error because the PHY
device is in error.
The conditions for such an error to occur are that we have a port of our
switch that is not disabled, and has the same port number as a PHY
address (say both 5) that can be probed using the DSA slave MII bus. We
end-up having this slave network device find a PHY at the same address
as our port number, and we try to attach to it.
A slave network (e.g: port 0) has already attached to our PHY device,
and we try to re-attach it with a different network device, but since we
ignore the error we would end-up initializating incorrect device
references by the time the slave network interface is opened.
The code has been (re)organized several times, making it hard to provide
an exact Fixes tag, this is a bugfix nonetheless.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the Marvell mv88e6xxx DSA driver made use of the HWMON support in
DSA. The temperature sensor registers are actually in the embedded
PHYs, and the PHY driver now supports it. So remove all HWMON support
from DSA and drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the DSA Ethernet switches are true Linux devices, the CPU
switch is not necessarily the first one. If its address is higher than
the second switch on the same MDIO bus, its index will be 1, not 0.
Avoid any confusion by using dst->cpu_switch instead of dst->ds[0].
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store a dsa_switch pointer to the CPU switch in the tree instead of only
its index. This avoids the need to initialize it to -1.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3a543ef479 ("net: dsa:
Implement ndo_get_phys_port_id") since it misuses the purpose of
ndo_get_phys_port_id(). We have ndo_get_phys_port_name() to do the
correct thing for us now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return the physical port number of a DSA created network device using
ndo_get_phys_port_name().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the new DTS bindings for DSA (dsa2), the "ethernet" and "link"
phandles are respectively mandatory and exclusive to CPU port and DSA
link device tree nodes.
Simplify dsa2.c a bit by checking the presence of such phandle instead
of checking the redundant "label" property.
Then the Linux philosophy for Ethernet switch ports is to expose them to
userspace as standard NICs by default. Thus use the standard enumerated
"eth%d" device name if no "label" property is provided for a user port.
This allows to save DTS files from subjective net device names.
If one wants to rename an interface, udev rules can be used as usual.
Of course the current behavior is unchanged, and the optional "label"
property for user ports has precedence over the enumerated name.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli
Juergen Beisert
Vivien Didelot
Sean Wang
Tobias Regnery
Andrew Lunn
David S. Miller