Rename this variable because it is the Receive indirection
table.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The break statement for the Macronix case is missing and will
fall through to the Winbond case and re-assign the size setting.
Fix this by adding the missing break statement. Also correctly
indent the return statements.
Detected by CoverityScan, CID#1458020 ("Missing break in switch")
Fixes: 96ac18f14a ("cxgb4: Add support for new flash parts")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Collect SGE, PCIE, PM, UP CIM, MA and HMA dumps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Try to access TP indirect registers via firmware first. If this fails,
fallback and access them directly. This ensures that driver and
firmware do not conflict each other while accessing the TP indirect
registers.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Collect firmware mbox and device logs before collecting the rest of
the hardware dumps to snap the firmware state before the mailbox logs
are updated by other hardware dumps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Collect EDC0 and EDC1 memory dump.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add base to collect dump entities. Collect register dump and
update template header accordingly.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement operations to set/get dump data via ethtool. Also add
template header that precedes dump data, which helps in decoding
and extracting the dump data.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today's -next build encountered an error due to a missing definition of
WARN_ON(), caused by some header reorganization removing an implicit
inclusion of linux/bug.h. Fix this with an explicit inclusion.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .set_addr function does nothing, remove the dsa_loop implementation
before getting rid of it completely in DSA.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As for mv88e6xxx, setup the switch from within the mv88e6060 driver with
a random MAC address, and remove the .set_addr implementation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E6060 Ethernet switch always transmits the multicast bit of the
switch MAC address as a zero. It re-uses the corresponding bit 8 of the
register "Switch MAC Address Register Bytes 0 & 1" for "DiffAddr".
If the "DiffAddr" bit is 0, then all ports transmit the same source
address. If it is set to 1, then bit 2:0 are used for the port number.
The mv88e6060 driver is currently wrongly shifting the MAC address byte
0 by 9. To fix this, shift it by 8 as usual and clear its bit 0.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An Ethernet switch may support having a MAC address, which can be used
as the switch's source address in transmitted full-duplex Pause frames.
If a DSA switch supports the related .set_addr operation, the DSA core
sets the master's MAC address on the switch. This won't make sense
anymore in a multi-CPU ports system, because there won't be a unique
master device assigned to a switch tree.
Instead, setup the switch from within the Marvell driver with a random
MAC address, and remove the .set_addr implementation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for direct packet access in TC, note that because
writing the packet will cause the verifier to generate a csum
fixup prologue we won't be able to offload packet writes from
TC, just yet, only the reads will work.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ability to write packet contents using pre-validated
packet pointers (direct packet access).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In direct packet access bound checks are already done, we can
simply dereference the packet pointer.
Verifier/parser logic needs to record pointer type. Note that
although verifier does protect us from CTX vs other pointer
changes we will also want to differentiate between PACKET vs
MAP_VALUE or STACK, so we can add the check already.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move data load into a separate function and separate it from
packet length checks of legacy I/O. This makes the code more
readable and easier to reuse.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sizes of fields in struct xdp_md/xdp_buff and some in sk_buff depend
on target architecture. Take that into account and use struct xdp_buff,
not struct xdp_md.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eBPF is host-endian specific. Translating both BE and LE eBPF
to the NFP is feasible, but would require quite a bit of indirection.
The fact that I don't have access to any BE hosts that would fit
a 25G/40G/100G NIC is also limiting my ability to test big endian.
For now restrict the offload to little endian hosts only.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement byte swaps with rotations, shifts and byte loads.
Remember to clear upper parts of the 64 bit registers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register move operation is encoded as alu no op. This means
that one has to specify number of unused/none parameters to
the emit_alu(). Add a helper.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have BPF assemebler support in LLVM 6 we can easily
test all compare instructions (LLVM 4 didn't generate most of them
from C). Fix the compare to immediates and refactor the order
of compare to regs to make sure they both follow the same pattern.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We optimize comparisons to immediate 0 as if (reg.lo | reg.hi).
The early return statement was missing, however, which means we
would generate two comparisons - optimized one followed by a
normal 2x 32 bit compare.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ld_field instruction has the following format in NFP assembler:
ld_field[dst, 1000, src, <<24]
reoder parameters to emit_ld_field_any() to make it closer to
the familiar assembler order.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control must be disabled for AVB enabled queues and TX
AVB queues must be enabled by setting BIT(2) of TXQEN.
Correct this by passing the queue mode to DMA callbacks
and by checking in these functions wether we are in AVB
performing the necessary adjustments.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we are using all the available fifo size in RQS and
TQS fields. This will not work correctly in multi-queues IP's
because total fifo size must be splitted to the enabled queues.
Correct this by computing the available fifo size per queue and
setting the right value in TQS and RQS fields.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The module clock is used for two purposes:
- Wake-on-LAN (WoL), which is optional,
- gPTP Timer Increment (GTI) configuration, which is mandatory.
As the clock is needed for GTI configuration anyway, WoL is always
available. Hence remove duplication and repeated obtaining of the clock
by making GTI use the stored clock for WoL use.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 4 very similar PHYs:
0x600d84a1: BCM54210E (rev B0)
0x600d84a2: BCM54210E (rev B1)
0x600d84a5: B50212E (rev B0)
0x600d84a6: B50212E (rev B1)
that need setting master mode manually. It's because they run in slave
mode by default with Automatic Slave/Master configuration disabled which
can lead to unreliable connection with massive ping loss.
So far it was reported for a board with BCM47189 SoC and B50212E B1 PHY
connected to the bgmac supported ethernet device. Telling PHY driver to
setup PHY properly solves this issue.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of Broadcom's PHYs run by default in slave mode with Automatic
Slave/Master configuration disabled. It stops them from working properly
with some devices.
So far it has been verified for BCM54210E and BCM50212E which don't
work well with Intel's I217-LM and I218-LM:
http://ark.intel.com/products/60019/Intel-Ethernet-Connection-I217-LMhttp://ark.intel.com/products/71307/Intel-Ethernet-Connection-I218-LM
I was told there is massive ping loss.
This commit adds support for a new flag which can be set by an ethernet
driver to fixup PHY setup.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the underlying master ever changes its L2 (e.g. bonding device),
then make sure that the IPvlan slaves always emit packets with the
current L2 of the master instead of the stale mac addr which was
copied during the device creation. The problem can be seen with
following script -
#!/bin/bash
# Create a vEth pair
ip link add dev veth0 type veth peer name veth1
ip link set veth0 up
ip link set veth1 up
ip link show veth0
ip link show veth1
# Create an IPvlan device on one end of this vEth pair.
ip link add link veth0 dev ipvl0 type ipvlan mode l2
ip link show ipvl0
# Change the mac-address of the vEth master.
ip link set veth0 address 02:11:22:33:44:55
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete unused channel variables in vxge-traffic.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have established the queue mapping between the switch port
egress queues and the SYSTEMPORT egress queues, we can turn on Advanced
Congestion Buffering (ACB) at the SYSTEMPORT level. This enables the
Ethernet MAC controller to get out of band flow control information
directly from the switch port and queue that it monitors such that its
internal TDMA can be appropriately backpressured.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turn on the out of band Advanced Congestion Buffering (ACB) mechanism at
the switch level now that we have properly established the queue mapping
between the switch egress queues and the SYSTEMPORT egress queues. This
allows the switch to correctly backpressure the host system when one of
its queue drops below the configured thresholds.
This is also helping achieve so called "lossless" behavior by adapting
the TX interrupt pacing to the actual speed and capacity of the switch
port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Establish a queue mapping between the DSA slave network device queues
created that correspond to switch port queues, and the transmit queue
that SYSTEMPORT manages.
We need to configure the SYSTEMPORT transmit queue with the switch port number
and switch port queue number in order for the switch and SYSTEMPORT hardware to
utilize the out of band congestion notification. This hardware mechanism works
by looking at the switch port egress queue and determines whether there is
enough buffers for this queue, with that class of service for a successful
transmission and if not, backpressures the SYSTEMPORT queue that is being used.
For this to work, we implement a notifier which looks at the
DSA_PORT_REGISTER event. When DSA network devices are registered, the
framework calls the DSA notifiers when that happens, extracts the number
of queues for these devices and their associated port number, remembers
that in the driver private structure and linearly maps those queues to
TX rings/queues that we manage.
This scheme works because DSA slave network deviecs always transmit
through SYSTEMPORT so when DSA slave network devices are
destroyed/brought down, the corresponding SYSTEMPORT queues are no
longer used. Also, by design of the DSA framework, the master network
device (SYSTEMPORT) is registered first.
For faster lookups we use an array of up to DSA_MAX_PORTS * number of
queues per port, and then map pointers to bcm_sysport_tx_ring such that
our ndo_select_queue() implementation can just index into that array to
locate the corresponding ring index.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit df1ec1b9d0.
It turns out that memory allocated via dma_alloc_coherent is always
aligned to the size of the buffer, so there's no way the RRD and RFD
can ever be in separate 32-bit regions.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In XDP_TX, some fields in tx_info and tx_desc are constants across
all entries of the different XDP_TX rings.
Assign values to these fields on ring creation time, rather than in
data-path.
Patchset performance tests:
Tested on ConnectX3Pro, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Single queue no-RSS optimization ON.
XDP_TX packet rate:
------------------------------
Before | After | Gain |
13.7 Mpps | 14.0 Mpps | %2.2 |
------------------------------
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function mlx4_en_tx_write_desc() is not optimized to use of XDP xmit.
Use the relevant parts inline instead.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct net_device parameter was passed only to extract
struct mlx4_en_priv out of it.
Here we pass the priv parameter directly.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only user of cls_flower->egress_dev is mlx5. So do the conversion
there alongside with the code originating the call in cls_flower
function fl_hw_replace_filter to the newly introduced egress device
callback infrastucture.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to bridge two devices which can send multiplexing and
aggregation (MAP) data. This is done only when the data itself is
not going to be consumed in the stack but is being passed on to a
different endpoint. This is mainly used for testing.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using a static array, use a hlist to store the muxed
endpoints and use the mux id to query the rmnet_device.
This is useful as usually very few mux ids are used.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rmnet_devices information is already stored in muxed_ep, so
storing this in rmnet_devices[] again is redundant.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The end point is set twice in the local_ep as well as the mux_id and
the real_dev in the rmnet private structure. Remove the local_ep.
While these elements are equivalent, rmnet_endpoint will be
used only as part of the rmnet_port for muxed scenarios in VND mode.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mode information on the real device makes it easier to route packets
to rmnet device or bridged device based on the configuration.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of these constants were used in the initial patchset where
custom netlink configuration was used and hence are no longer relevant.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be rewritten in the following patches.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the error messages that are printed by the interrupt handlers
are poorly written. For example, many don't include a device prefix,
so there's no indication that they are EMAC errors.
Also use rate limiting for all messages that could be printed from
interrupt context.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang
Colin Ian King
Rahul Lakkireddy
Mark Brown
Vivien Didelot
Jakub Kicinski
Jose Abreu
Geert Uytterhoeven
Rafał Miłecki
Mahesh Bandewar
Christos Gkekas
Florian Fainelli
Timur Tabi
Tariq Toukan
Jiri Pirko
Subash Abhinov Kasiviswanathan