Граф коммитов

62 Коммитов

Автор SHA1 Сообщение Дата
Greg Kroah-Hartman 3b8a1f45e1 Merge 5.1-rc6 into tty-next
We want the serial/tty fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-21 23:20:08 +02:00
Guoqing Jiang c53051128b sc16is7xx: put err_spi and err_i2c into correct #ifdef
err_spi is only called within SERIAL_SC16IS7XX_SPI
while err_i2c is called inside SERIAL_SC16IS7XX_I2C.
So we need to put err_spi and err_i2c into each #ifdef
accordingly.

This change fixes ("sc16is7xx: move label 'err_spi'
to correct section").

Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-19 14:09:23 +02:00
Guoqing Jiang e00164a0f0 sc16is7xx: move label 'err_spi' to correct section
err_spi is used when SERIAL_SC16IS7XX_SPI is enabled, so make
the label only available under SERIAL_SC16IS7XX_SPI option.
Otherwise, the below warning appears.

drivers/tty/serial/sc16is7xx.c:1523:1: warning: label ‘err_spi’ defined but not used [-Wunused-label]
 err_spi:
  ^~~~~~~

Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Fixes: ac0cdb3d99 ("sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-16 15:24:38 +02:00
Greg Kroah-Hartman b63d443be4 Merge 5.1-rc3 into tty-next
We want the tty/serial fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-01 07:40:47 +02:00
Andy Shevchenko 6b77908fea serial: sc16is7xx: Drop of_match_ptr() use
There is an ACPI method to enumerate such devices via specific ACPI ID
and use of compatible strings. It will not work for the drivers which
have no OF match ID table present.

Reported-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Tested-By: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-28 00:30:51 +09:00
Andy Shevchenko 00d9f0c654 serial: sc16is7xx: Switch to use device_get_match_data()
Instead of open coded variants, switch to direct use of
device_get_match_data().

Tested-By: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-28 00:30:51 +09:00
Andy Shevchenko 24bc6e68ef serial: sc16is7xx: Respect clock-frequency property
If the property is provided and there are no other possibilities to detect
UART clock frequency, use it as a fallback.

Tested-By: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-28 00:30:50 +09:00
Mao Wenan ac0cdb3d99 sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()
Add the missing uart_unregister_driver() and i2c_del_driver() before return
from sc16is7xx_init() in the error handling case.

Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-19 15:37:44 +01:00
Gustavo A. R. Silva 84f1c5c017 sc16is7xx: Use struct_size() in devm_kzalloc()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    void *entry[];
};

instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);

This code was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-08 16:56:04 +01:00
Phil Elwell 30ec514d44 sc16is7xx: Fix for "Unexpected interrupt: 8"
The SC16IS752 has an Enhanced Feature Register which is aliased at the
same address as the Interrupt Identification Register; accessing it
requires that a magic value is written to the Line Configuration
Register. If an interrupt is raised while the EFR is mapped in then
the ISR won't be able to access the IIR, leading to the "Unexpected
interrupt" error messages.

Avoid the problem by claiming a mutex around accesses to the EFR
register, also claiming the mutex in the interrupt handler work
item (this is equivalent to disabling interrupts to interlock against
a non-threaded interrupt handler).

See: https://github.com/raspberrypi/linux/issues/2529

Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-18 16:07:25 +02:00
Phil Elwell 8344498721 sc16is7xx: Fix for multi-channel stall
The SC16IS752 is a dual-channel device. The two channels are largely
independent, but the IRQ signals are wired together as an open-drain,
active low signal which will be driven low while either of the
channels requires attention, which can be for significant periods of
time until operations complete and the interrupt can be acknowledged.
In that respect it is should be treated as a true level-sensitive IRQ.

The kernel, however, needs to be able to exit interrupt context in
order to use I2C or SPI to access the device registers (which may
involve sleeping).  Therefore the interrupt needs to be masked out or
paused in some way.

The usual way to manage sleeping from within an interrupt handler
is to use a threaded interrupt handler - a regular interrupt routine
does the minimum amount of work needed to triage the interrupt before
waking the interrupt service thread. If the threaded IRQ is marked as
IRQF_ONESHOT the kernel will automatically mask out the interrupt
until the thread runs to completion. The sc16is7xx driver used to
use a threaded IRQ, but a patch switched to using a kthread_worker
in order to set realtime priorities on the handler thread and for
other optimisations. The end result is non-threaded IRQ that
schedules some work then returns IRQ_HANDLED, making the kernel
think that all IRQ processing has completed.

The work-around to prevent a constant stream of interrupts is to
mark the interrupt as edge-sensitive rather than level-sensitive,
but interpreting an active-low source as a falling-edge source
requires care to prevent a total cessation of interrupts. Whereas
an edge-triggering source will generate a new edge for every interrupt
condition a level-triggering source will keep the signal at the
interrupting level until it no longer requires attention; in other
words, the host won't see another edge until all interrupt conditions
are cleared. It is therefore vital that the interrupt handler does not
exit with an outstanding interrupt condition, otherwise the kernel
will not receive another interrupt unless some other operation causes
the interrupt state on the device to be cleared.

The existing sc16is7xx driver has a very simple interrupt "thread"
(kthread_work job) that processes interrupts on each channel in turn
until there are no more. If both channels are active and the first
channel starts interrupting while the handler for the second channel
is running then it will not be detected and an IRQ stall ensues. This
could be handled easily if there was a shared IRQ status register, or
a convenient way to determine if the IRQ had been deasserted for any
length of time, but both appear to be lacking.

Avoid this problem (or at least make it much less likely to happen)
by reducing the granularity of per-channel interrupt processing
to one condition per iteration, only exiting the overall loop when
both channels are no longer interrupting.

Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-18 16:07:25 +02:00
Stefan Potyra e76785d092 sc16is7xx: Check for an error when the clock is enabled.
When the clock is enabled, check if there is an error. Otherwise
clk_get_rate() can be called without enabled clock.

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 0814e8d5da ("sc16is7xx: enable the clock")
Signed-off-by: Stefan Potyra <Stefan.Potyra@elektrobit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-25 14:56:12 +02:00
Greg Kroah-Hartman 4793f2ebff tty: serial: Remove redundant license text
Now that the SPDX tag is in all tty files, that identifies the license
in a specific and legally-defined manner.  So the extra GPL text wording
can be removed as it is no longer needed at all.

This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text.  And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.

No copyright headers or other non-license-description text was removed.

Cc: Jiri Slaby <jslaby@suse.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-08 13:08:12 +01:00
Greg Kroah-Hartman e3b3d0f549 tty: add SPDX identifiers to all remaining files in drivers/tty/
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.

Update the drivers/tty files files with the correct SPDX license
identifier based on the license text in the file itself.  The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.

This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.

Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-08 13:08:12 +01:00
Ingo Molnar ae7e81c077 sched/headers: Prepare for new header dependencies before moving code to <uapi/linux/sched/types.h>
We are going to move scheduler ABI details to <uapi/linux/sched/types.h>,
which will be used from a number of .c files.

Create empty placeholder header that maps to <linux/types.h>.

Include the new header in the files that are going to need it.

Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2017-03-02 08:42:27 +01:00
Greg Kroah-Hartman 5131dcd781 Merge 4.9-rc3 into tty-next
We want the serial/tty fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-30 06:42:10 -04:00
Francois Berder 03842c1739 sc16is7xx: always write state when configuring GPIO as an output
The regmap_update first reads the IOState register and then triggers
a write if needed. However, GPIOS might be configured as an input so
 the read to IOState on this GPIO is the current state which might
be random.

Signed-off-by: Francois Berder <Francois.Berder@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27 16:42:31 +02:00
Josh Cartwright 04da73803c sc16is7xx: Drop bogus use of IRQF_ONESHOT
The use of IRQF_ONESHOT when registering an interrupt handler with
request_irq() is non-sensical.

Not only that, it also prevents the handler from being threaded when it
otherwise should be w/ IRQ_FORCED_THREADING is enabled.  This causes the
following deadlock observed by Sean Nyekjaer on -rt:

Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[..]
   rt_spin_lock_slowlock from queue_kthread_work
   queue_kthread_work from sc16is7xx_irq
   sc16is7xx_irq [sc16is7xx] from handle_irq_event_percpu
   handle_irq_event_percpu from handle_irq_event
   handle_irq_event from handle_level_irq
   handle_level_irq from generic_handle_irq
   generic_handle_irq from mxc_gpio_irq_handler
   mxc_gpio_irq_handler from mx3_gpio_irq_handler
   mx3_gpio_irq_handler from generic_handle_irq
   generic_handle_irq from __handle_domain_irq
   __handle_domain_irq from gic_handle_irq
   gic_handle_irq from __irq_svc
   __irq_svc from rt_spin_unlock
   rt_spin_unlock from kthread_worker_fn
   kthread_worker_fn from kthread
   kthread from ret_from_fork

Fixes: 9e6f4ca3e5 ("sc16is7xx: use kthread_worker for tx_work and irq")
Reported-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Josh Cartwright <joshc@ni.com>
Cc: linux-rt-users@vger.kernel.org
Cc: Jakub Kicinski <moorray3@wp.pl>
Cc: stable@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27 16:27:24 +02:00
Petr Mladek 3989144f86 kthread: kthread worker API cleanup
A good practice is to prefix the names of functions by the name
of the subsystem.

The kthread worker API is a mix of classic kthreads and workqueues.  Each
worker has a dedicated kthread.  It runs a generic function that process
queued works.  It is implemented as part of the kthread subsystem.

This patch renames the existing kthread worker API to use
the corresponding name from the workqueues API prefixed by
kthread_:

__init_kthread_worker()		-> __kthread_init_worker()
init_kthread_worker()		-> kthread_init_worker()
init_kthread_work()		-> kthread_init_work()
insert_kthread_work()		-> kthread_insert_work()
queue_kthread_work()		-> kthread_queue_work()
flush_kthread_work()		-> kthread_flush_work()
flush_kthread_worker()		-> kthread_flush_worker()

Note that the names of DEFINE_KTHREAD_WORK*() macros stay
as they are. It is common that the "DEFINE_" prefix has
precedence over the subsystem names.

Note that INIT() macros and init() functions use different
naming scheme. There is no good solution. There are several
reasons for this solution:

  + "init" in the function names stands for the verb "initialize"
    aka "initialize worker". While "INIT" in the macro names
    stands for the noun "INITIALIZER" aka "worker initializer".

  + INIT() macros are used only in DEFINE() macros

  + init() functions are used close to the other kthread()
    functions. It looks much better if all the functions
    use the same scheme.

  + There will be also kthread_destroy_worker() that will
    be used close to kthread_cancel_work(). It is related
    to the init() function. Again it looks better if all
    functions use the same naming scheme.

  + there are several precedents for such init() function
    names, e.g. amd_iommu_init_device(), free_area_init_node(),
    jump_label_init_type(),  regmap_init_mmio_clk(),

  + It is not an argument but it was inconsistent even before.

[arnd@arndb.de: fix linux-next merge conflict]
 Link: http://lkml.kernel.org/r/20160908135724.1311726-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/1470754545-17632-3-git-send-email-pmladek@suse.com
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-10-11 15:06:33 -07:00
Florian Vallee 43c51bb573 sc16is7xx: make sure device is in suspend once probed
Previously sc16is7xx_power was called in order to set the device to a
  low power mode.

  However since SC16IS7XX_EFR_ENABLE_BIT was not set beforehand this
  suspend request had not effect.

  Also, soft-reset the device prior to port initialization. It may
  otherwise be in a state (interrupt pending, fifo not empty) which
  prevents it from sleeping.

Signed-off-by: Florian Vallee <fvallee@eukrea.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-31 16:05:26 +02:00
Linus Torvalds e10abc629f TTY and Serial driver update for 4.7-rc1
Here's the large TTY and Serial driver update for 4.7-rc1.
 
 A few new serial drivers are added here, and Peter has fixed a bunch of
 long-standing bugs in the tty layer and serial drivers as normal.  Full
 details in the shortlog.
 
 All of these have been in linux-next for a while with no reported issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlc/0/oACgkQMUfUDdst+ynzyQCgsa54VNijdAzU6AA5HEfqmf2M
 cGMAn1boH7hUWlAbJmzzihx4JASoGjYW
 =V5VH
 -----END PGP SIGNATURE-----

Merge tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty and serial driver updates from Greg KH:
 "Here's the large TTY and Serial driver update for 4.7-rc1.

  A few new serial drivers are added here, and Peter has fixed a bunch
  of long-standing bugs in the tty layer and serial drivers as normal.
  Full details in the shortlog.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (88 commits)
  MAINTAINERS: 8250: remove website reference
  serial: core: Fix port mutex assert if lockdep disabled
  serial: 8250_dw: fix wrong logic in dw8250_check_lcr()
  tty: vt, finish looping on duplicate
  tty: vt, return error when con_startup fails
  QE-UART: add "fsl,t1040-ucc-uart" to of_device_id
  serial: mctrl_gpio: Drop support for out1-gpios and out2-gpios
  serial: 8250dw: Add device HID for future AMD UART controller
  Fix OpenSSH pty regression on close
  serial: mctrl_gpio: add IRQ locking
  serial: 8250: Integrate Fintek into 8250_base
  serial: mps2-uart: add support for early console
  serial: mps2-uart: add MPS2 UART driver
  dt-bindings: document the MPS2 UART bindings
  serial: sirf: Use generic uart-has-rtscts DT property
  serial: sirf: Introduce helper variable struct device_node *np
  serial: mxs-auart: Use generic uart-has-rtscts DT property
  serial: imx: Use generic uart-has-rtscts DT property
  doc: DT: Add Generic Serial Device Tree Bindings
  serial: 8250: of: Make tegra_serial_handle_break() static
  ...
2016-05-20 20:57:27 -07:00
Wills Wang e69ef01ff0 sc16is7xx: remove useless "uart_handle_cts_change"
SC16is7xx has feature for auto hardware flow control using RTS/CTS,
so we don't need "uart_handle_cts_change" to invoke "start_tx/stop_tx"
for flow control.

In addition, for software CTS, interrupt "SC16IS7XX_IIR_CTSRTS_SRC"
just report the nCTS change of state from active(low) to inactive(high),
driver don't know when the state of nCTS change from incactive to active,
so can't resume the transmission when a peer device is again ready and
re-assert nRTS signal.

Signed-off-by: Wills Wang <wills.wang@live.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-04-30 09:26:55 -07:00
Linus Walleij dee07cea54 serial: sc16is7xx: use gpiochip data pointer
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-04-26 15:35:39 +02:00
Greg Kroah-Hartman 5f5357335e Revert "sc16is7xx: implemented get_mctrl"
This reverts commit a3f0b77f36.

Maarten writes:
	It appears to be wrong and I don't have a good idea how to fix
	it yet.

Cc: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
2016-03-07 16:10:08 -08:00
Maarten Brock a3f0b77f36 sc16is7xx: implemented get_mctrl
Add support for manual getting the modem control lines.

Signed-off-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-02-14 17:39:36 -08:00
Maarten Brock b7dfdea859 sc16is7xx: implemented set_mctrl
Add support for manual setting the modem control lines.

Signed-off-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-02-14 17:39:36 -08:00
Wills Wang b7ed5161f1 sc16is7xx: fix incorrect register bits macro
In datasheet, Modem Status Register MSR[4-7] reflect the modem pins
CTS/DSR/RI/CD signal state.

Signed-off-by: Wills Wang <wills.wang@live.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-02-06 22:46:17 -08:00
Linus Torvalds 58cf279aca GPIO bulk updates for the v4.5 kernel cycle:
Infrastructural changes:
 
 - In struct gpio_chip, rename the .dev node to .parent to better reflect
   the fact that this is not the GPIO struct device abstraction. We will
   add that soon so this would be totallt confusing.
 
 - It was noted that the driver .get_value() callbacks was
   sometimes reporting negative -ERR values to the gpiolib core, expecting
   them to be propagated to consumer gpiod_get_value() and gpio_get_value()
   calls. This was not happening, so as there was a mess of drivers
   returning negative errors and some returning "anything else than zero"
   to indicate that a line was active. As some would have bit 31 set to
   indicate "line active" it clashed with negative error codes. This is
   fixed by the largeish series clamping values in all drivers with
   !!value to [0,1] and then augmenting the code to propagate error codes
   to consumers. (Includes some ACKed patches in other subsystems.)
 
 - Add a void *data pointer to struct gpio_chip. The container_of() design
   pattern is indeed very nice, but we want to reform the struct gpio_chip
   to be a non-volative, stateless business, and keep states internal to
   the gpiolib to be able to hold on to the state when adding a proper
   userspace ABI (character device) further down the road. To achieve this,
   drivers need a handle at the internal state that is not dependent on
   their struct gpio_chip() so we add gpiochip_add_data() and
   gpiochip_get_data() following the pattern of many other subsystems.
   All the "use gpiochip data pointer" patches transforms drivers to this
   scheme.
 
 - The Generic GPIO chip header has been merged into the general
   <linux/gpio/driver.h> header, and the custom header for that removed.
   Instead of having a separate mm_gpio_chip struct for these generic
   drivers, merge that into struct gpio_chip, simplifying the code and
   removing the need for separate and confusing includes.
 
 Misc improvements:
 
 - Stabilize the way GPIOs are looked up from the ACPI legacy
   specification.
 
 - Incremental driver features for PXA, PCA953X, Lantiq (patches from the
   OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
 
 New drivers:
 
 - Add a GPIO chip to the ALSA SoC AC97 driver.
 
 - Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
   the branch is merged here too to account for infrastructural changes).
 
 - The sx150x driver now supports the sx1502.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJWmsZhAAoJEEEQszewGV1ztq0QAJ1KbNOpmf/s3INkOH4r771Z
 WIrNEsmwwLIAryo8gKNOM0H1zCwhRUV7hIE5jYWgD6JvjuAN6vobMlZAq21j6YpB
 pKgqnI5DuoND450xjb8wSwGQ5NTYp1rFXNmwCrtyTjOle6AAW+Kp2cvVWxVr77Av
 uJinRuuBr9GOKW/yYM1Fw/6EPjkvvhVOb+LBguRyVvq0s5Peyw7ZVeY1tjgPHJLn
 oSZ9dmPUjHEn91oZQbtfro3plOObcxdgJ8vo//pgEmyhMeR8XjXES+aUfErxqWOU
 PimrZuMMy4cxnsqWwh3Dyxo7KSWfJKfSPRwnGwc/HgbHZEoWxOZI1ezRtGKrRQtj
 vubxp5dUBA5z66TMsOCeJtzKVSofkvgX2Wr/Y9jKp5oy9cHdAZv9+jEHV1pr6asz
 Tas97MmmO77XuRI/GPDqVHx8dfa15OIz9s92+Gu64KxNzVxTo4+NdoPSNxkbCILO
 FKn7EmU3D0OjmN2NJ9GAURoFaj3BBUgNhaxacG9j2bieyh+euuUHRtyh2k8zXR9y
 8OnY1UOrTUYF8YIq9pXZxMQRD/lqwCNHvEjtI6BqMcNx4MptfTL+FKYUkn/SgCYk
 QTNV6Ui+ety5D5aEpp5q0ItGsrDJ2LYSItsS+cOtMy2ieOxbQav9NWwu7eI3l5ly
 gwYTZjG9p9joPXLW0E3g
 =63rR
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "Here is the bulk of GPIO changes for v4.5.

  Notably there are big refactorings mostly by myself, aimed at getting
  the gpio_chip into a shape that makes me believe I can proceed to
  preserve state for a proper userspace ABI (character device) that has
  already been proposed once, but resulted in the feedback that I need
  to go back and restructure stuff.  So I've been restructuring stuff.
  On the way I ran into brokenness (return code from the get_value()
  callback) and had to fix it.  Also, refactored generic GPIO to be
  simpler.

  Some of that is still waiting to trickle down from the subsystems all
  over the kernel that provide random gpio_chips, I've touched every
  single GPIO driver in the kernel now, oh man I didn't know I was
  responsible for so much...

  Apart from that we're churning along as usual.

  I took some effort to test and retest so it should merge nicely and we
  shook out a couple of bugs in -next.

  Infrastructural changes:

   - In struct gpio_chip, rename the .dev node to .parent to better
     reflect the fact that this is not the GPIO struct device
     abstraction.  We will add that soon so this would be totallt
     confusing.

   - It was noted that the driver .get_value() callbacks was sometimes
     reporting negative -ERR values to the gpiolib core, expecting them
     to be propagated to consumer gpiod_get_value() and gpio_get_value()
     calls.  This was not happening, so as there was a mess of drivers
     returning negative errors and some returning "anything else than
     zero" to indicate that a line was active.  As some would have bit
     31 set to indicate "line active" it clashed with negative error
     codes.  This is fixed by the largeish series clamping values in all
     drivers with !!value to [0,1] and then augmenting the code to
     propagate error codes to consumers.  (Includes some ACKed patches
     in other subsystems.)

   - Add a void *data pointer to struct gpio_chip.  The container_of()
     design pattern is indeed very nice, but we want to reform the
     struct gpio_chip to be a non-volative, stateless business, and keep
     states internal to the gpiolib to be able to hold on to the state
     when adding a proper userspace ABI (character device) further down
     the road.  To achieve this, drivers need a handle at the internal
     state that is not dependent on their struct gpio_chip() so we add
     gpiochip_add_data() and gpiochip_get_data() following the pattern
     of many other subsystems.  All the "use gpiochip data pointer"
     patches transforms drivers to this scheme.

   - The Generic GPIO chip header has been merged into the general
     <linux/gpio/driver.h> header, and the custom header for that
     removed.  Instead of having a separate mm_gpio_chip struct for
     these generic drivers, merge that into struct gpio_chip,
     simplifying the code and removing the need for separate and
     confusing includes.

  Misc improvements:

   - Stabilize the way GPIOs are looked up from the ACPI legacy
     specification.

   - Incremental driver features for PXA, PCA953X, Lantiq (patches from
     the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48

  New drivers:

   - Add a GPIO chip to the ALSA SoC AC97 driver.

   - Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
     but the branch is merged here too to account for infrastructural
     changes).

   - The sx150x driver now supports the sx1502"

* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
  gpio: generic: make bgpio_pdata always visible
  gpiolib: fix chip order in gpio list
  gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
  gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
  gpio: brcmstb: Allow building driver for BMIPS_GENERIC
  gpio: brcmstb: Set endian flags for big-endian MIPS
  gpio: moxart: fix build regression
  gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
  leds: pca9532: use gpiochip data pointer
  leds: tca6507: use gpiochip data pointer
  hid: cp2112: use gpiochip data pointer
  bcma: gpio: use gpiochip data pointer
  avr32: gpio: use gpiochip data pointer
  video: fbdev: via: use gpiochip data pointer
  gpio: pch: Optimize pch_gpio_get()
  Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
  pinctrl: nsp-gpio: use gpiochip data pointer
  pinctrl: vt8500-wmt: use gpiochip data pointer
  pinctrl: exynos5440: use gpiochip data pointer
  pinctrl: at91-pio4: use gpiochip data pointer
  ...
2016-01-17 12:32:01 -08:00
Florian Achleitner ed7a85045d sc16is7xx: Fix TX buffer overrun caused by wrong tx fifo level read-out
We found that our sc16is7xx on spi reported a TX fifo free space value
(TXLVL_REG) of 255 ocassionally, which is obviously wrong, with a
64 byte fifo and caused a buffer overrun and a kernel crash.

To trigger this, a large write to the tty is sufficient. The fifo fills,
TXLVL_REG reads zero, but the handle_tx function does a zero-data-length
write to the TX fifo anyways through sc16is7xx_fifo_write. The next
TXLVL_REG read then yields 255, for unknown reasons. A subsequent read
is ok.

Prevent zero-data-length writes if the TX fifo is full, because they are
pointless, and because they trigger wrong TXLVL read-outs.

Furthermore, prevent a TX buffer overrun if the peripheral reports values
larger than the buffer size and thus, don't allow the peripheral to crash
the kernel.

Signed-off-by: Florian Achleitner <achleitner.florian@fronius.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-13 19:59:48 -08:00
Linus Walleij 58383c7842 gpio: change member .dev to .parent
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.

This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:

@@
struct gpio_chip *var;
@@
-var->dev
+var->parent

and:

@@
struct gpio_chip var;
@@
-var.dev
+var.parent

and:

@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent

Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.

This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.

Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-19 09:24:35 +01:00
Linus Torvalds 75f5db39ff spi: Updates for v4.4
Quite a lot of activity in SPI this cycle, almost all of it in drivers
 with a few minor improvements and tweaks in the core.
 
  - Updates to pxa2xx to support Intel Broxton and multiple chip selects.
  - Support for big endian in the bcm63xx driver.
  - Multiple slave support for the mt8173
  - New driver for the auxiliary SPI controller in bcm2835 SoCs.
  - Support for Layerscale SoCs in the Freescale DSPI driver.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
 sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
 iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
 hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
 BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
 TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
 =DgXG
 -----END PGP SIGNATURE-----

Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "Quite a lot of activity in SPI this cycle, almost all of it in drivers
  with a few minor improvements and tweaks in the core.

   - Updates to pxa2xx to support Intel Broxton and multiple chip selects.
   - Support for big endian in the bcm63xx driver.
   - Multiple slave support for the mt8173
   - New driver for the auxiliary SPI controller in bcm2835 SoCs.
   - Support for Layerscale SoCs in the Freescale DSPI driver"

* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
  spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
  spi: pxa2xx: Add support for Intel Broxton
  spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
  spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
  spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
  spi: Add DSPI support for layerscape family
  spi: ti-qspi: improve ->remove() callback
  spi/spi-xilinx: Fix race condition on last word read
  spi: Drop owner assignment from spi_drivers
  spi: Add THIS_MODULE to spi_driver in SPI core
  spi: Setup the master controller driver before setting the chipselect
  spi: dw: replace magic constant by DW_SPI_DR
  spi: mediatek: mt8173 spi multiple devices support
  spi: mediatek: handle controller_data in mtk_spi_setup
  spi: mediatek: remove mtk_spi_config
  spi: mediatek: Update document devicetree bindings to support multiple devices
  spi: fix kernel-doc warnings about missing return desc in spi.c
  spi: fix kernel-doc warnings about missing return desc in spi.h
  spi: pxa2xx: Align a few defines
  spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
  ...
2015-11-05 13:15:12 -08:00
Andrew F. Davis 3821a065f5 spi: Drop owner assignment from spi_drivers
An spi_driver does not need to set an owner, it will be populated by the
driver core.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-10-28 10:30:17 +09:00
Sean Nyekjaer 2b0159d1ec sc16is7xx: null ptr check
If a wrong compatible flag in specified, the of_match_device
returning null.
Implemented check and if NULL then returning -ENODEV.

Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-04 19:14:26 +01:00
Javier Martinez Canillas 20b5af9350 serial: sc16is7xx: Remove unnecessary MODULE_ALIAS()
The driver has a I2C device id table that is used to create the modaliases
and also "sc16is7xx" is not a supported I2C id, so it's never used.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-04 17:44:52 +01:00
Jakub Kicinski 68be64ca7e sc16is7xx: constify devtype
devtype structures are all declared as const.
Compiler does not complain because we cast
their pointers to save them in .driver_data.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:27 -07:00
Jakub Kicinski c64349722d sc16is7xx: support multiple devices
We currently register the uart driver during device probe
which makes it hard to support more than one chip.
Move the driver registration to module init/exit time and
preallocate space for up to 8 lines (4-8 chips).

Reported-by: Michael Allwright <michael.allwright@upb.de>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:27 -07:00
Jakub Kicinski e92a886bf7 sc16is7xx: save and use per-chip line number
In preparation of supporting multiple devices we should save
the per-chip line number (0 or 1), because the uart_port line
will reflect system-wide uart number and will be offseted for
chips other than the first to register.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:27 -07:00
Greg Kroah-Hartman 92311e46ec Merge 4.2-rc4 into tty-next
Other serial driver work wants to build on patches now in 4.2-rc4 so
merge the branch so this can properly happen.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-07-27 11:12:39 -07:00
Krzysztof Kozlowski 7e8af24fbe tty: serial: Drop owner assignment from i2c_driver
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-07-23 18:04:59 -07:00
Bo Svangård dec273ecc1 sc16is7xx: fix FIFO address of secondary UART
Calls to regmap_raw_read/write needed register rewrite in a
similar way as function calls to regmap_read/write already had.
This enables reading/writing the serial datastream to the device.

Signed-off-by: Bo Svangård <bo.svangard@embeddedart.se>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-07-23 15:32:32 -07:00
Jakub Kicinski 478d1051a0 sc16is7xx: use kworker for RS-485 configuration
RS-485 configuration is also done under the spinlock
so no blocking I/O allowed.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:47:27 +09:00
Jakub Kicinski 059d581530 sc16is7xx: use kworker to update ier bits
.stop_rx/tx() are called in atomic context, we cannot use
blocking I/O. While at it correct the name of RX bit and
'*' placement in pointer declarations.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:47:27 +09:00
Jakub Kicinski a010408536 sc16is7xx: use kworker for md_proc
Convert md_proc into general async reconfiguration procedure.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:47:27 +09:00
Jakub Kicinski dbe5a40cba sc16is7xx: move RTS delay to workqueue
Instead of spinning under port->lock let's just sleep
inside the kthread.  It should be equivalent as TX cannot
proceed when thread is blocked.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:47:27 +09:00
Jakub Kicinski 9e6f4ca3e5 sc16is7xx: use kthread_worker for tx_work and irq
Convert workqueue usage to a real-time kworker.  The problem
with workqueues is that we cannot set real-time priorities on
our work and asynchronous reconfiguration can be blocked by
less important tasks.

We need kthread for the interrupt anyway and because we will
now be using single kthread for all TX-related operations we
can get rid of the port mutex.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:47:27 +09:00
Jakub Kicinski 4ae82e5d23 sc16is7xx: use LSR_TEMT_BIT in .tx_empty()
LSR_TEMT_BIT (LSR bit 6) provides us exactly the information
we need to determine if transmission is finished - FIFO level
and shift register empty.  We can save ourselves reading FIFO
level explicitly if we use this bit.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:47:27 +09:00
Jakub Kicinski 4117a60c8e sc16is7xx: add missing compatible strings
Without matching bus-specific strings driver will not be loaded
automatically.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:47:27 +09:00
Jakub Kicinski 5451bb29f7 sc16is7xx: remove RS-485 delay RTS handling
Users of RS-485 can request via ioctl that RTS signals should
be activated selected number of milliseconds before the actual
data transmission or delay reception certain number of milli-
seconds after the transmission is finished.  In sc16is7xx,
however, RTS signalling is handled by the hardware and driver
has no way of providing this feature.

We still try to provide .delay_rts_before_send by delaying
transmission but without actual effect on the RTS line.

Note: this change will make the driver return -EINVAL when the
      feature is requested (.delay_rts_after_send is set).

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:45:28 +09:00
Rama Kiran Kumar Indrakanti 2c837a8a8f sc16is7xx: spi interface is added
spi interface for sc16is7xx is added along with Kconfig flag
to enable spi or i2c, thus in a instance we can have either
spi or i2c or both, in sync to the hw.

Signed-off-by: Rama Kiran Kumar Indrakanti <indrakanti_ram@hotmail.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:45:27 +09:00
Jakub Kicinski f0e381158a sc16is7xx: expose RTS inversion in RS-485 mode
Hardware is capable of inverting RTS signal when working
in RS-485 mode.  Expose this functionality to user space.
Relay on a matching combination of standard flags
(SER_RS485_RTS_ON_SEND and SER_RS485_RTS_AFTER_SEND) to
detect when user space is requesting inverted RTS mode.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-04-10 14:43:48 +02:00