We must ensure that the tag is not changed while we aggregate the
requests. Currently the icc_set_tag() is not using any locks and this
may cause the values to be aggregated incorrectly. Fix this by acquiring
the icc_lock while we set the tag.
Link: https://lore.kernel.org/lkml/20191018141750.17032-1-georgi.djakov@linaro.org/
Fixes: 127ab2cc5f ("interconnect: Add support for path tags")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
This is a struct with a trailing zero-length array of icc_node pointers
but it's allocated as if it were a single array of icc_nodes instead.
This allocates too much memory at probe time but shouldn't have any
noticeable effect. Both sdm845 and qcs404 are affected.
Fix by replacing kcalloc with kzalloc and using the "struct_size" macro.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 5e4e6c4d3a ("interconnect: qcom: Add QCS404 interconnect provider driver")
Link: https://lore.kernel.org/linux-pm/a7360abb6561917e30bbfaa6084578449152bf1d.1569348056.git.leonard.crestez@nxp.com/
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
The macro to generate a Bus Controller Manager (BCM) TCS command is used
by the interconnect driver but might also be interesting to other
drivers that need to construct TCS commands for sub processors so move
it out of the sdm845 specific file and into the header.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
There is one compilation error when CONFIG_INTERCONNECT_QCOM_QCS404=y and
CONFIG_INTERCONNECT_QCOM_SMD_RPM=y, as well as CONFIG_COMPILE_TEST=y,
but CONFIG_QCOM_SMD_RPM is not set, logs as below:
drivers/interconnect/qcom/smd-rpm.o: In function `qcom_icc_rpm_smd_send':
smd-rpm.c:(.text+0xe4): undefined reference to `qcom_rpm_smd_write'
Makefile:1071: recipe for target 'vmlinux' failed
make: *** [vmlinux] Error 1
This is because
INTERCONNECT_QCOM_QCS404 depends on QCOM_SMD_RPM || COMPILE_TEST.
Here CONFIG_COMPILE_TEST=y, so CONFIG_INTERCONNECT_QCOM_SMD_RPM
is selected. If CONFIG_QCOM_SMD_RPM is not set, then
qcom_rpm_smd_write() is not defined, and compilation error happen.
Fix this by removing COMPILE_TEST from CONFIG_INTERCONNECT_QCOM_QCS404.
Fixes: 5e4e6c4d3a ("interconnect: qcom: Add QCS404 interconnect provider driver")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add driver for the interconnect buses found in Qualcomm QCS404-based
platforms. The topology consists of three NoCs that are controlled by
a remote processor. This remote processor collects the aggregated
bandwidth for each master-slave pairs.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
On some Qualcomm SoCs, there is a remote processor, which controls some of
the Network-On-Chip interconnect resources. Other CPUs express their needs
by communicating with this processor. Add a driver to handle communication
with this remote processor.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add support for wake and sleep commands by using a tag to indicate
whether or not the aggregate and set requests fall into execution
state specific bucket.
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Introduce an optional callback in interconnect provider drivers. It can be
used for implementing actions, that need to be executed before the actual
aggregation of the bandwidth requests has started.
The benefit of this for now is that it will significantly simplify the code
in provider drivers.
Suggested-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Consumers may have use cases with different bandwidth requirements based
on the system or driver state. The consumer driver can append a specific
tag to the path and pass this information to the interconnect platform
driver to do the aggregation based on this state.
Introduce icc_set_tag() function that will allow the consumers to append
an optional tag to each path. The aggregation of these tagged paths is
platform specific.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
When consumers report their bandwidth needs with icc_set_bw(), it's
possible that the requested amount of bandwidth is not available or just
the new configuration fails to apply on some path. In this case revert to
the previous configuration and propagate the error back to the consumers
to let them know that bandwidth is not available, hardware is busy or
whatever error is returned by the interconnect platform driver.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce Qualcomm SDM845 specific provider driver using the
interconnect framework.
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a functionality to provide information about the current constraints
per each node and provider.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we support only platform data for specifying the interconnect
endpoints. As now the endpoints are hard-coded into the consumer driver
this may lead to complications when a single driver is used by multiple
SoCs, which may have different interconnect topology.
To avoid cluttering the consumer drivers, introduce a translation function
to help us get the board specific interconnect data from device-tree.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces a new API to get requirements and configure the
interconnect buses across the entire chipset to fit with the current
demand.
The API is using a consumer/provider-based model, where the providers are
the interconnect buses and the consumers could be various drivers.
The consumers request interconnect resources (path) between endpoints and
set the desired constraints on this data flow path. The providers receive
requests from consumers and aggregate these requests for all master-slave
pairs on that path. Then the providers configure each node along the path
to support a bandwidth that satisfies all bandwidth requests that cross
through that node. The topology could be complicated and multi-tiered and
is SoC specific.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Brian Masney
Georgi Djakov
Leonard Crestez
Jordan Crouse
Mao Wenan
Bjorn Andersson
David Dai
Thomas Gleixner
Yangtao Li